Frédéric Danis [Tue, 20 Aug 2024 14:17:16 +0000 (16:17 +0200)]
Bluetooth: hci_ldisc: Use speed set by btattach as oper_speed
Starting a BCM UART controller not defined as a platform device or
a serdev with "btattach -B /dev/ttyS1 -P bcm -S 3000000" works fine
but the serial port remains at the init_speed, i.e. 115200.
The oper_speed is only set if a device is declared in ACPI, device
tree or as a platform device.
This commit copies the serial port speed fixed by hciattach to the
oper_speed on line discipline opening.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Kuan-Wei Chiu [Sat, 10 Aug 2024 14:14:15 +0000 (22:14 +0800)]
Bluetooth: hci_conn: Remove redundant memset after kzalloc
Since kzalloc already zeroes the allocated memory, the subsequent
memset call is unnecessary. This patch removes the redundant memset to
clean up the code and enhance efficiency.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bartosz Golaszewski [Mon, 19 Aug 2024 07:48:01 +0000 (09:48 +0200)]
dt-bindings: bluetooth: bring the HW description closer to reality for wcn6855
Describe the inputs from the PMU that the Bluetooth module on wcn6855
consumes and drop the ones from the host. This breaks the current
contract but the only two users of wcn6855 upstream - sc8280xp based
boards - will be updated in DTS patches sent separately while the
hci_qca driver will remain backwards compatible with older DT sources.
Acked-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Fri, 16 Aug 2024 11:13:09 +0000 (16:43 +0530)]
Bluetooth: btnxpuart: Add support for ISO packets
This enables btnxpuart driver to handle ISO RX packet when DUT is
configured as audio sink.
Tested IW612 on iMX8MMini platform and BlueZ-5.77 as follows:
1) Configured DUT with bap_bcast_sink role in pipewire configuration file.
2) Started pipewire and DUT is able to sync with Broadcast source through
pipewire.
3) ISO data RX is seen in btmon.
4) Audio/Music is heard on audio jack.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Tested-by: Sarveshwar Bajaj <sarveshwar.bajaj@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Mon, 12 Aug 2024 15:01:15 +0000 (11:01 -0400)]
Bluetooth: btusb: Invert LE State flag to set invalid rather then valid
This inverts the LE State flag so by default we assume the controllers
would report valid states rather than invalid so it is inline with the
respective quirk (HCI_QUIRK_BROKEN_LE_STATES).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
ASoC: meson: Remove unused declartion in header file
The declaration of aiu_fifo_hw_free() has been removed since
commit e05cde84eabc ("ASoC: meson: Use managed DMA buffer allocation").
Let's remove the unused declaration.
Fixes: e05cde84eabc ("ASoC: meson: Use managed DMA buffer allocation") Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://patch.msgid.link/20240910122330.70684-1-zhangzekun11@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Li [Fri, 9 Aug 2024 05:42:25 +0000 (13:42 +0800)]
Bluetooth: hci_uart: Add support for Amlogic HCI UART
Add a new HCI protocol HCI_UART_AML for the Amlogic Bluetooth
controller. It works on the standard H4 protocol via a 4-wire UART
interface, with baud rates up to 4 Mbps.
The controller supports two types of commands: the TCI commands and the
vendor command. The former is for initial setup including setting baud
rates, downloading fw, starting chip and etc, while the latter is for
dumping firmware versions and setting public address after firmware
updates and normal startup.
It was verified on board of T602 (S905X4 + W265S2).
dmesg:
..
[ 5.313450] Bluetooth: HCI UART protocol AML registered
[ 6.506052] Bluetooth: hci0: fw_version: date = 42.28, number = 0xb2fd
...
Co-developed-by: Ye He <ye.he@amlogic.com> Signed-off-by: Ye He <ye.he@amlogic.com> Signed-off-by: Yang Li <yang.li@amlogic.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Yang Li [Fri, 9 Aug 2024 05:42:24 +0000 (13:42 +0800)]
dt-bindings: net: bluetooth: Add support for Amlogic Bluetooth
Add binding document for Amlogic Bluetooth chipsets attached over UART.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Yang Li <yang.li@amlogic.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Alexander Hall [Tue, 30 Jul 2024 22:08:25 +0000 (15:08 -0700)]
Bluetooth: btusb: Add MediaTek MT7925-B22M support ID 0x13d3:0x3604
This patch fixes bluetooth support on the MediaTek MT7925 WiFi 7 +
BT 5.3 M.2 chipset that I purchased from aliexpress (and which
arrived today). The PCB states that it is an MT7925B22M.
High fidelity images I took of the chip itself for future reference:
https://archive.org/details/MediaTek-MT7925B22M/
Webpage the chip was purchased from, note it is different from the
images taken:
https://web.archive.org/web/20240620021119/https://www.aliexpress.
us/item/3256806821207897.html
Signed-off-by: Alexander Hall <bearodark@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Merge tag 'mvebu-arm-6.12-1' of https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/arm
mvebu arm for 6.12 (part 1)
Fix a few warning error with W=1
Switch orion5x to new sys-off handler API
* tag 'mvebu-arm-6.12-1' of https://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dove: Drop a write-only variable
ARM: orion5x: Switch to new sys-off handler API
ARM: mvebu: Warn about memory chunks too small for DDR training
Merge tag 'trace-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Move declaration of interface_lock outside of CONFIG_TIMERLAT_TRACER
The fix to some locking races moved the declaration of the
interface_lock up in the file, but also moved it into the
CONFIG_TIMERLAT_TRACER #ifdef block, breaking the build when that
wasn't set. Move it further up and out of that #ifdef block.
- Remove unused function run_tracer_selftest() stub
When CONFIG_FTRACE_STARTUP_TEST is not set the stub function
run_tracer_selftest() is not used and clang is warning about it.
Remove the function stub as it is not needed.
* tag 'trace-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Drop unused helper function to fix the build
tracing/osnoise: Fix build when timerlat is not enabled
Leo Li [Thu, 5 Sep 2024 22:45:04 +0000 (18:45 -0400)]
drm/amd/display: Do not reset planes based on crtc zpos_changed
[Why]
drm_normalize_zpos will set the crtc_state->zpos_changed to 1 if any of
it's assigned planes changes zpos, or is removed/added from it.
To have amdgpu_dm request a plane reset on this is too broad. For
example, if only the cursor plane was moved from one crtc to another,
the crtc's zpos_changed will be set to true. But that does not mean that
the underlying primary plane requires a reset.
[How]
Narrow it down so that only the plane that has a change in zpos will
require a reset.
As a future TODO, we can further optimize this by only requiring a reset
on z-order change. Z-order is different from z-pos, since a zpos change
doesn't necessarily mean the z-ordering changed, and DC should only
require a reset if the z-ordering changed.
For example, the following zpos update does not change z-ordering:
Plane A: zpos 2 -> 3
Plane B: zpos 1 -> 2
=> Plane A is still on top of plane B: no reset needed
Whereas this one does change z-ordering:
Plane A: zpos 2 -> 1
Plane B: zpos 1 -> 2
=> Plane A changed from on top, to below plane B: reset needed
Fixes: 38e0c3df6dbd ("drm/amd/display: Move PRIMARY plane zpos higher") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3569 Signed-off-by: Leo Li <sunpeng.li@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
io_uring/rw: drop -EOPNOTSUPP check in __io_complete_rw_common()
A recent change ensured that the necessary -EOPNOTSUPP -> -EAGAIN
transformation happens inline on both the reader and writer side,
and hence there's no need to check for both of these anymore on
the completion handler side.
io_uring/rw: treat -EOPNOTSUPP for IOCB_NOWAIT like -EAGAIN
Some file systems, ocfs2 in this case, will return -EOPNOTSUPP for
an IOCB_NOWAIT read/write attempt. While this can be argued to be
correct, the usual return value for something that requires blocking
issue is -EAGAIN.
A refactoring io_uring commit dropped calling kiocb_done() for
negative return values, which is otherwise where we already do that
transformation. To ensure we catch it in both spots, check it in
__io_read() itself as well.
T.J. Mercier [Mon, 9 Sep 2024 20:53:59 +0000 (20:53 +0000)]
drm/syncobj: Fix syncobj leak in drm_syncobj_eventfd_ioctl
A syncobj reference is taken in drm_syncobj_find, but not released if
eventfd_ctx_fdget or kzalloc fails. Put the reference in these error
paths.
Reported-by: Xingyu Jin <xingyuj@google.com> Fixes: c7a472297169 ("drm/syncobj: add IOCTL to register an eventfd") Signed-off-by: T.J. Mercier <tjmercier@google.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by. Christian König <christian.koenig@amd.com> CC: stable@vger.kernel.org # 6.6+ Link: https://patchwork.freedesktop.org/patch/msgid/20240909205400.3498337-1-tjmercier@google.com Signed-off-by: Christian König <christian.koenig@amd.com>
btrfs: only unlock the to-be-submitted ranges inside a folio
[SUBPAGE COMPRESSION LIMITS]
Currently inside writepage_delalloc(), if a delalloc range is going to
be submitted asynchronously (inline or compression, the page
dirty/writeback/unlock are all handled in at different time, not at the
submission time), then we return 1 and extent_writepage() will skip the
submission.
This is fine if every sector matches page size, but if a sector is
smaller than page size (aka, subpage case), then it can be very
problematic, for example for the following 64K page:
0 16K 32K 48K 64K
|/| |///////| |/|
| |
4K 52K
Where |/| is the dirty range we need to submit.
In the above case, we need the following different handling for the 3
ranges:
- [0, 4K) needs to be submitted for regular write
A single sector cannot be compressed.
- [16K, 32K) needs to be submitted for compressed write
- [48K, 52K) needs to be submitted for regular write.
Above, if we try to submit [16K, 32K) for compressed write, we will
return 1 and immediately, and without submitting the remaining
[48K, 52K) range.
Furthermore, since extent_writepage() will exit without unlocking any
sectors, the submitted range [0, 4K) will not have sector unlocked.
That's the reason why for now subpage is only allowed for full page
range.
[ENHANCEMENT]
- Introduce a submission bitmap at btrfs_bio_ctrl::submit_bitmap
This records which sectors will be submitted by extent_writepage_io().
This allows us to track which sectors needs to be submitted thus later
to be properly unlocked.
For asynchronously submitted range (inline/compression), the
corresponding bits will be cleared from that bitmap.
- Only return 1 if no sector needs to be submitted in
writepage_delalloc()
- Only submit sectors marked by submission bitmap inside
extent_writepage_io()
So we won't touch the asynchronously submitted part.
- Introduce btrfs_folio_end_writer_lock_bitmap() helper
This will only unlock the involved sectors specified by @bitmap
parameter, to avoid touching the range asynchronously submitted.
Please note that, since subpage compression is still limited to page
aligned range, this change is only a preparation for future sector
perfect compression support for subpage.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: merge btrfs_folio_unlock_writer() into btrfs_folio_end_writer_lock()
The function btrfs_folio_unlock_writer() is already calling
btrfs_folio_end_writer_lock() to do the heavy lifting work, the only
missing 0 writer check.
Thus there is no need to keep two different functions, move the 0 writer
check into btrfs_folio_end_writer_lock(), and remove
btrfs_folio_unlock_writer().
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Leo Martins [Tue, 3 Sep 2024 18:19:05 +0000 (11:19 -0700)]
btrfs: DEFINE_FREE for struct btrfs_path
Add a DEFINE_FREE for struct btrfs_path. This defines a function that
can be called using the __free attribute. Define a macro
BTRFS_PATH_AUTO_FREE to make the declaration of an auto freeing path
very clear.
The intended use is to define the auto free of path in cases where the
path is allocated somewhere at the beginning and freed either on all
error paths or at the end of the function.
int func() {
BTRFS_PATH_AUTO_FREE(path);
if (...)
return -ERROR;
path = alloc_path();
...
if (...)
return -ERROR;
...
return 0;
}
Signed-off-by: Leo Martins <loemra.dev@gmail.com>
[ update changelog ] Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 30 Aug 2024 07:18:20 +0000 (16:48 +0930)]
btrfs: remove btrfs_folio_end_all_writers()
The function btrfs_folio_end_all_writers() is only utilized in
extent_writepage() as a way to unlock all subpage range (for both
successful submission and error handling).
Meanwhile we have a similar function, btrfs_folio_end_writer_lock().
The difference is, btrfs_folio_end_writer_lock() expects a range that is
a subset of the already locked range.
This limit on btrfs_folio_end_writer_lock() is a little overkilled,
preventing it from being utilized for error paths.
So here we enhance btrfs_folio_end_writer_lock() to accept a superset of
the locked range, and only end the locked subset.
This means we can replace btrfs_folio_end_all_writers() with
btrfs_folio_end_writer_lock() instead.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Wed, 26 Jun 2024 21:39:11 +0000 (23:39 +0200)]
btrfs: constify more pointer parameters
Continue adding const to parameters. This is for clarity and minor
addition to safety. There are some minor effects, in the assembly code
and .ko measured on release config.
David Sterba [Wed, 5 Jun 2024 00:28:30 +0000 (02:28 +0200)]
btrfs: rework BTRFS_I as macro to preserve parameter const
Currently BTRFS_I is a static inline function that takes a const inode
and returns btrfs inode, dropping the 'const' qualifier. This can break
assumptions of compiler though it seems there's no real case.
To make the parameter and return type consistent regardint const we can
use the container_of_const() that preserves it. However this would not
check the parameter type. To fix that use the same _Generic construct
but implement only the two expected types.
Filipe Manana [Thu, 29 Aug 2024 18:03:52 +0000 (19:03 +0100)]
btrfs: add and use helper to verify the calling task has locked the inode
We have a few places that check if we have the inode locked by doing:
ASSERT(inode_is_locked(vfs_inode));
This actually proved to be useful several times as if assertions are
enabled (and by default they are in many distros) it immediately triggers
a crash which is impossible for users to miss.
However that doesn't check if the lock is held by the calling task, so
the check passes if some other task locked the inode.
Using one of the lockdep functions to check the lock is held, like
lockdep_assert_held() for example, does check that the calling task
holds the lock, and if that's not the case it produces a warning and
stack trace in dmesg. However, despite the misleading "assert" in the
name of the lockdep helpers, it does not trigger a crash/BUG_ON(), just
a warning and splat in dmesg, which is easy to get unnoticed by users
who may have lockdep enabled.
So add a helper that does the ASSERT() and calls lockdep_assert_held()
immediately after and use it every where we check the inode is locked.
Like this if the lock is held by some other task we get the warning
in dmesg which is caught by fstests, very helpful during development,
and may also be occassionaly noticed by users with lockdep enabled.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:08 +0000 (02:29 +0800)]
btrfs: convert copy_inline_to_page() to use folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Moreover find_or_create_page() is compatible API, and it can
replaced with __filemap_get_folio(). Some interfaces have been converted
to use folio before, so the conversion operation from page can be
eliminated here.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:07 +0000 (02:29 +0800)]
btrfs: convert btrfs_decompress() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Based on the previous patch, the compression path can be
directly used in folio without converting to page.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:06 +0000 (02:29 +0800)]
btrfs: convert zstd_decompress() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. And memcpy_to_page() can be replaced with memcpy_to_folio().
But there is no memzero_folio(), but it can be replaced equivalently by
folio_zero_range().
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:05 +0000 (02:29 +0800)]
btrfs: convert lzo_decompress() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. And memcpy_to_page() can be replaced with memcpy_to_folio().
But there is no memzero_folio(), but it can be replaced equivalently by
folio_zero_range().
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:04 +0000 (02:29 +0800)]
btrfs: convert zlib_decompress() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. And memcpy_to_page() can be replaced with memcpy_to_folio().
But there is no memzero_folio(), but it can be replaced equivalently by
folio_zero_range().
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:03 +0000 (02:29 +0800)]
btrfs: convert try_release_extent_mapping() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. And page_to_inode() can be replaced with folio_to_inode() now.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:02 +0000 (02:29 +0800)]
btrfs: convert try_release_extent_state() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Moreover, use folio_pos() instead of page_offset(),
which is more consistent with folio usage.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:01 +0000 (02:29 +0800)]
btrfs: convert submit_eb_page() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:29:00 +0000 (02:29 +0800)]
btrfs: convert submit_eb_subpage() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Moreover, use folio_pos() instead of page_offset(),
which is more consistent with folio usage.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:28:59 +0000 (02:28 +0800)]
btrfs: convert read_key_bytes() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Moreover, use kmap_local_folio() instead of kmap_local_page(),
which is more consistent with folio usage.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:28:58 +0000 (02:28 +0800)]
btrfs: convert try_release_extent_buffer() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:28:57 +0000 (02:28 +0800)]
btrfs: convert try_release_subpage_extent_buffer() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. And use folio_pos instead of page_offset, which is more
consistent with folio usage. At the same time, folio_test_private() can
handle folio directly without converting from page to folio first.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:28:56 +0000 (02:28 +0800)]
btrfs: convert get_next_extent_buffer() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Use folio_pos instead of page_offset, which is more
consistent with folio usage.
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Li Zetao [Wed, 28 Aug 2024 18:28:55 +0000 (02:28 +0800)]
btrfs: convert clear_page_extent_mapped() to take a folio
The old page API is being gradually replaced and converted to use folio
to improve code readability and avoid repeated conversion between page
and folio. Now clear_page_extent_mapped() can deal with a folio
directly, so change its name to clear_folio_extent_mapped().
Signed-off-by: Li Zetao <lizetao1@huawei.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 29 May 2024 07:33:47 +0000 (17:03 +0930)]
btrfs: make compression path to be subpage compatible
Currently btrfs compression path is not really subpage compatible, every
thing is still done in page unit.
That's fine for regular sector size and subpage routine. As even for
subpage routine compression is only enabled if the whole range is page
aligned, so reading the page cache in page unit is totally fine.
However in preparation for the future subpage perfect compression
support, we need to change the compression routine to properly handle a
subpage range.
This patch would prepare both zlib and zstd to only read the subpage
range for compression.
Lzo is already doing subpage aware read, as lzo's on-disk format is
already sectorsize dependent.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Sat, 24 Aug 2024 10:06:43 +0000 (19:36 +0930)]
btrfs: merge btrfs_orig_bbio_end_io() into btrfs_bio_end_io()
There are only two differences between the two functions:
- btrfs_orig_bbio_end_io() does extra error propagation
This is mostly to allow tolerance for write errors.
- btrfs_orig_bbio_end_io() does extra pending_ios check
This check can handle both the original bio, or the cloned one.
(All accounting happens in the original one).
This makes btrfs_orig_bbio_end_io() a much safer call.
In fact we already had a double freeing error due to usage of
btrfs_bio_end_io() in the error path of btrfs_submit_chunk().
So just move the whole content of btrfs_orig_bbio_end_io() into
btrfs_bio_end_io().
For normal paths this brings no change, because they are already calling
btrfs_orig_bbio_end_io() in the first place.
For error paths (not only inside bio.c but also external callers), this
change will introduce extra checks, especially for external callers, as
they will error out without submitting the btrfs bio.
But considering it's already in the error path, such slower but much
safer checks are still an overall win.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Fri, 16 Aug 2024 19:16:24 +0000 (15:16 -0400)]
btrfs: do not hold the extent lock for entire read
Historically we've held the extent lock throughout the entire read.
There's been a few reasons for this, but it's mostly just caused us
problems. For example, this prevents us from allowing page faults
during direct io reads, because we could deadlock. This has forced us
to only allow 4k reads at a time for io_uring NOWAIT requests because we
have no idea if we'll be forced to page fault and thus have to do a
whole lot of work.
On the buffered side we are protected by the page lock, as long as we're
reading things like buffered writes, punch hole, and even direct IO to a
certain degree will get hung up on the page lock while the page is in
flight.
On the direct side we have the dio extent lock, which acts much like the
way the extent lock worked previously to this patch, however just for
direct reads. This protects direct reads from concurrent direct writes,
while we're protected from buffered writes via the inode lock.
Now that we're protected in all cases, narrow the extent lock to the
part where we're getting the extent map to submit the reads, no longer
holding the extent lock for the entire read operation. Push the extent
lock down into do_readpage() so that we're only grabbing it when looking
up the extent map. This portion was contributed by Goldwyn.
Co-developed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Mon, 19 Aug 2024 20:50:01 +0000 (16:50 -0400)]
btrfs: take the dio extent lock during O_DIRECT operations
Currently we hold the extent lock for the entire duration of a read.
This isn't really necessary in the buffered case, we're protected by the
page lock, however it's necessary for O_DIRECT.
For O_DIRECT reads, if we only locked the extent for the part where we
get the extent, we could potentially race with an O_DIRECT write in the
same region. This isn't really a problem, unless the read is delayed so
much that the write does the COW, unpins the old extent, and some other
application re-allocates the extent before the read is actually able to
be submitted. At that point at best we'd have a checksum mismatch, but
at worse we could read data that doesn't belong to us.
To address this potential race we need to make sure we don't have
overlapping, concurrent direct io reads and writes.
To accomplish this use the new EXTENT_DIO_LOCKED bit in the direct IO
case in the same spot as the current extent lock. The writes will take
this while they're creating the ordered extent, which is also used to
make sure concurrent buffered reads or concurrent direct reads are not
allowed to occur, and drop it after the ordered extent is taken. For
reads it will act as the current read behavior for the EXTENT_LOCKED
bit, we set it when we're starting the read, we clear it in the end_io
to allow other direct writes to continue.
This still has the drawback of disallowing concurrent overlapping direct
reads from occurring, but that exists with the current extent locking.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Mon, 19 Aug 2024 18:15:52 +0000 (14:15 -0400)]
btrfs: introduce EXTENT_DIO_LOCKED
In order to support dropping the extent lock during a read we need a way
to make sure that direct reads and direct writes for overlapping ranges
are protected from each other. To accomplish this introduce another
lock bit specifically for direct io. Subsequent patches will utilize
this to protect direct IO operations.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 27 Aug 2024 02:26:51 +0000 (04:26 +0200)]
btrfs: always pass readahead state to defrag
Defrag ioctl passes readahead from the file, but autodefrag does not
have a file so the readahead state is allocated when needed.
The autodefrag loop in cleaner thread iterates over inodes so we can
simply provide an on-stack readahead state and will not need to allocate
it in btrfs_defrag_file(). The size is 32 bytes which is acceptable.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 27 Aug 2024 02:10:11 +0000 (04:10 +0200)]
btrfs: return void from btrfs_add_inode_defrag()
The potential memory allocation failure is not a fatal error, skipping
autodefrag is fine and the caller inode_should_defrag() does not care
about the errors. Further writes can attempt to add the inode back to
the defragmentation list again.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 27 Aug 2024 02:05:48 +0000 (04:05 +0200)]
btrfs: clear defragmented inodes using postorder in btrfs_cleanup_defrag_inodes()
btrfs_cleanup_defrag_inodes() is not called frequently, only in remount
or unmount, but the way it frees the inodes in fs_info->defrag_inodes
is inefficient. Each time it needs to locate first node, remove it,
potentially rebalance tree until it's done. This allows to do a
conditional reschedule.
For cleanups the rbtree_postorder_for_each_entry_safe() iterator is
convenient but we can't reschedule and restart iteration because some of
the tree nodes would be already freed.
The cleanup operation is kmem_cache_free() which will likely take the
fast path for most objects so rescheduling should not be necessary.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 14 Aug 2024 01:20:21 +0000 (10:50 +0930)]
btrfs: remove the nr_ret parameter from __extent_writepage_io()
The parameter @nr_ret is used to tell the caller how many sectors have
been submitted for IO.
Then callers check @nr_ret value to determine if we need to manually
clear the PAGECACHE_TAG_DIRTY, as if we submitted no sector (e.g. all
sectors are beyond i_size) there is no folio_start_writeback() called thus
PAGECACHE_TAG_DIRTY tag will not be cleared.
Remove this parameter by:
- Moving the btrfs_folio_clear_writeback() call into
__extent_writepage_io()
So that if we didn't submit any IO, then manually call
btrfs_folio_set_writeback() to clear PAGECACHE_TAG_DIRTY when
the page is no longer dirty.
- Use a bool to record if we have submitted any sector
Instead of an int.
- Use subpage compatible helpers to end folio writeback.
This brings no change to the behavior, just for the sake of consistency.
As for the call site inside __extent_writepage(), we're always called
for the whole page, so the existing full page helper
folio_(start|end)_writeback() is totally fine.
For the call site inside extent_write_locked_range(), although we can
have subpage range, folio_start_writeback() will only clear
PAGECACHE_TAG_DIRTY if the page is no longer dirty, and the full folio
will still be dirty if there is any subpage dirty range.
Only when the last dirty subpage sector is cleared, the
folio_start_writeback() will clear PAGECACHE_TAG_DIRTY.
So no matter if we call the full page or subpage helper, the result
is still the same, then just use the subpage helpers for consistency.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Junchao Sun [Fri, 7 Jun 2024 14:30:21 +0000 (22:30 +0800)]
btrfs: qgroup: use xarray to track dirty extents in transaction
Use xarray to track dirty extents to reduce the size of the struct
btrfs_qgroup_extent_record from 64 bytes to 40 bytes. The xarray is
more cache line friendly, it also reduces the complexity of insertion
and search code compared to rb tree.
Another change introduced is about error handling. Before this patch,
the result of btrfs_qgroup_trace_extent_nolock() is always a success. In
this patch, because of this function calls the function xa_store() which
has the possibility to fail, so mark qgroup as inconsistent if error
happened and then free preallocated memory. Also we preallocate memory
before spin_lock(), if memory preallcation failed, error handling is the
same the existing code.
Suggested-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Junchao Sun <sunjunchao2870@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 7 Aug 2024 05:01:54 +0000 (14:31 +0930)]
btrfs: refactor __extent_writepage_io() to do sector-by-sector submission
Unlike the bitmap usage inside raid56, for __extent_writepage_io() we
handle the subpage submission not sector-by-sector, but for each dirty
range we found.
This is not a big deal normally, as the subpage complex code is already
mostly optimized out by the compiler for x86_64.
However for the sake of consistency and for the future of subpage
sector-perfect compression support, this patch does:
- Extract the sector submission code into submit_one_sector()
- Add the needed code to extract the dirty bitmap for subpage case
There is a small pitfall for non-subpage case, as we cleared page
dirty before starting writeback, so we have to manually set
the default dirty_bitmap to 1 for such case.
- Use bitmap_and() to calculate the target sectors we need to submit
This is done for both subpage and non-subpage cases, and will later
be expanded to skip inline/compression ranges.
For x86_64, the dirty bitmap will be fixed to 1, with the length of 1,
so we're still doing the same workload per sector.
For larger page sizes, the overhead will be a little larger, as previous
we only need to do one extent_map lookup per-dirty-range, but now it
will be one extent_map lookup per-sector.
But that is the same frequency as x86_64, so we're just aligning the
behavior to x86_64.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 30 Aug 2024 07:05:48 +0000 (16:35 +0930)]
btrfs: subpage: fix the bitmap dump which can cause bitmap corruption
In commit 75258f20fb70 ("btrfs: subpage: dump extra subpage bitmaps for
debug") an internal macro GET_SUBPAGE_BITMAP() is introduced to grab the
bitmap of each attribute.
But that commit is using bitmap_cut() which will do the left shift of
the larger bitmap, causing incorrect values.
Thankfully this bitmap_cut() is only called for debug usage, and so far
it's not yet causing problem.
Fix it to use bitmap_read() to only grab the desired sub-bitmap.
Fixes: 75258f20fb70 ("btrfs: subpage: dump extra subpage bitmaps for debug") CC: stable@vger.kernel.org # 6.6+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Tue, 13 Aug 2024 11:36:40 +0000 (13:36 +0200)]
btrfs: reduce chunk_map lookups in btrfs_map_block()
Currently we're calling btrfs_num_copies() before btrfs_get_chunk_map() in
btrfs_map_block(). But btrfs_num_copies() itself does a chunk map lookup
to be able to calculate the number of copies.
So split out the code getting the number of copies from btrfs_num_copies()
into a helper called btrfs_chunk_map_num_copies() and directly call it
from btrfs_map_block() and btrfs_num_copies().
This saves us one rbtree lookup per btrfs_map_block() invocation.
Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Wed, 7 Aug 2024 16:13:58 +0000 (17:13 +0100)]
btrfs: directly wake up cleaner kthread in the BTRFS_IOC_SYNC ioctl
The BTRFS_IOC_SYNC ioctl wants to wake up the cleaner kthread so that it
does any pending work (subvolume deletion, delayed iputs, etc), however
it is waking up the transaction kthread, which in turn wakes up the
cleaner. Since we don't have any transaction to commit, as any ongoing
transaction was already committed when it called btrfs_sync_fs() and
the goal is just to wake up the cleaner thread, directly wake up the
cleaner instead of the transaction kthread.
Reviewed-by: Boris Burkov <boris@bur.io> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 5 Aug 2024 05:32:54 +0000 (15:02 +0930)]
btrfs: make btrfs_is_subpage() to return false directly for 4K page size
Btrfs only supports sectorsize 4K, 8K, 16K, 32K, 64K for now, thus for
systems with 4K page size, there is no way the fs is subpage (sectorsize
< PAGE_SIZE).
So here we define btrfs_is_subpage() different according to the
PAGE_SIZE:
- PAGE_SIZE > 4K
We may hit real subpage cases, define btrfs_is_subpage() as a regular
function and do the usual checks.
- PAGE_SIZE == 4K (no smaller PAGE_SIZE support AFAIK)
There is no way the fs is subpage, so just define btrfs_is_subpage()
as an inline function which always return false.
This saves about 7K bytes for x86_64 debug builds:
text data bss dec hex filename
Before: 1484452 168693 25776 1678921 199e49 fs/btrfs/btrfs.ko
After: 1476605 168445 25776 1670826 197eaa fs/btrfs/btrfs.ko
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Wed, 31 Jul 2024 20:43:07 +0000 (22:43 +0200)]
btrfs: change RST lookup error message level to debug
Now that RAID stripe-tree lookup failures are not treated as a fatal issue
any more, change the RAID stripe-tree lookup error message to debug level.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Wed, 31 Jul 2024 20:43:06 +0000 (22:43 +0200)]
btrfs: don't readahead the relocation inode on RST
On relocation we're doing readahead on the relocation inode, but if the
filesystem is backed by a RAID stripe tree we can get ENOENT (e.g. due to
preallocated extents not being mapped in the RST) from the lookup.
But readahead doesn't handle the error and submits invalid reads to the
device, causing an assertion in the scatter-gather list code:
So in case of a relocation on a RAID stripe-tree based file system, skip
the readahead.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Wed, 31 Jul 2024 20:43:04 +0000 (22:43 +0200)]
btrfs: rename btrfs_io_stripe::is_scrub to rst_search_commit_root
Rename 'btrfs_io_stripe::is_scrub' to 'rst_search_commit_root'. While
'is_scrub' describes the state of the io_stripe (it is a stripe submitted
by scrub) it does not describe the purpose, namely looking at the commit
root when searching RAID stripe-tree entries.
Renaming the stripe to rst_search_commit_root describes this purpose.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Johannes Thumshirn [Wed, 31 Jul 2024 20:43:03 +0000 (22:43 +0200)]
btrfs: don't dump stripe-tree on lookup error
This just creates unnecessary noise and doesn't provide any insights into
debugging RAID stripe-tree related issues.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Boris Burkov [Wed, 31 Jul 2024 19:41:06 +0000 (12:41 -0700)]
btrfs: add comment about locking in cow_file_range_inline()
Add a comment to document the complicated locked_page unlock logic in
cow_file_range_inline. The specifically tricky part is that a caller
just up the stack converts ret == 0 to ret == 1 and then another
caller far up the callstack handles ret == 1 as a success, AND returns
without cleanup in that case, both of which "feel" unnatural and led to
the original bug.
Try to document that somewhat specific callstack logic here to explain
the weird un-setting of locked_folio on success.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Thu, 25 Jul 2024 10:48:10 +0000 (11:48 +0100)]
btrfs: more efficient chunk map iteration when device replace finishes
When iterating the chunk maps when a device replace finishes we are doing
a full rbtree search for each chunk map, which is not the most efficient
thing to do, wasting CPU time. As we are holding a write lock on the tree
during the whole iteration, we can simply start from the first node in the
tree and then move to the next chunk map by doing a rb_next() call - the
only exception is when we need to reschedule, in which case we have to do
a full rbtree search since we dropped the write lock and the tree may have
changed (chunk maps may have been removed and the tree got rebalanced).
So just do that.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Thu, 25 Jul 2024 09:46:01 +0000 (10:46 +0100)]
btrfs: reschedule when updating chunk maps at the end of a device replace
At the end of a device replace we must go over all the chunk maps and
update their stripes to point to the target device instead of the source
device. We iterate over the chunk maps while holding a write lock and
we never reschedule, which can result in monopolizing a CPU for too long
and blocking readers for too long (it's a rw lock, non-blocking).
So improve on this by rescheduling if necessary. This is safe because at
this point we are holding the chunk mutex, which means no new chunks can
be allocated and therefore we don't risk missing a new chunk map that
covers a range behind the last one we processed before rescheduling.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Thu, 25 Jul 2024 00:22:32 +0000 (20:22 -0400)]
btrfs: convert btrfs_set_range_writeback() to use a folio
We already use a lot of functions here that use folios, update the
function to use __filemap_get_folio instead of find_get_page and then
use the folio directly.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
projects / users / willy / xarray.git / log