On some systems using edge triggered ACPI Event Interrupts, the initial
state at boot is not setup by the firmware, instead relying on the edge
irq event handler running at least once to setup the initial state.
2 known examples of this are:
1) The Surface 3 has its _LID state controlled by an ACPI operation region
triggered by a GPIO event:
Method (_E4C, 0, Serialized) // _Exx: Edge-Triggered GPE
{
If ((HELD == One))
{
^^LID.LIDB = One
}
Else
{
^^LID.LIDB = Zero
Notify (LID, 0x80) // Status Change
}
Notify (^^PCI0.SPI1.NTRG, One) // Device Check
}
Currently, the state of LIDB is wrong until the user actually closes or
open the cover. We need to trigger the GPIO event once to update the
internal ACPI state.
Coincidentally, this also enables the Surface 2 integrated HID sensor hub
which also requires an ACPI gpio operation region to start initialization.
2) Various Bay Trail based tablets come with an external USB mux and
TI T1210B USB phy to enable USB gadget mode. The mux is controlled by a
GPIO which is controlled by an edge triggered ACPI Event Interrupt which
monitors the micro-USB ID pin.
When the tablet is connected to a PC (or no cable is plugged in), the ID
pin is high and the tablet should be in gadget mode. But the GPIO
controlling the mux is initialized by the firmware so that the USB data
lines are muxed to the host controller.
This means that if the user wants to use gadget mode, the user needs to
first plug in a host-cable to force the ID pin low and then unplug it
and connect the tablet to a PC, to get the ACPI event handler to run and
switch the mux to device mode,
This commit fixes both by running the event-handler once on boot.
Note that the running of the event-handler is done from a late_initcall,
this is done because the handler AML code may rely on OperationRegions
registered by other builtin drivers. This avoids errors like these:
[ 0.133026] ACPI Error: No handler for Region [XSCG] ((____ptrval____)) [GenericSerialBus] (20180531/evregion-132)
[ 0.133036] ACPI Error: Region GenericSerialBus (ID=9) has no handler (20180531/exfldio-265)
[ 0.133046] ACPI Error: Method parse/execution failed \_SB.GPO2._E12, AE_NOT_EXIST (20180531/psparse-516)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
[hdegoede: Document BYT USB mux reliance on initial trigger]
[hdegoede: Run event handler from a late_initcall, rather then immediately] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of memcg_online_kmem() failure, memcg_cgroup::id remains hashed
in mem_cgroup_idr even after memcg memory is freed. This leads to leak
of ID in mem_cgroup_idr.
This patch adds removal into mem_cgroup_css_alloc(), which fixes the
problem. For better readability, it adds a generic helper which is used
in mem_cgroup_alloc() and mem_cgroup_id_put_many() as well.
Link: http://lkml.kernel.org/r/152354470916.22460.14397070748001974638.stgit@localhost.localdomain
Fixes 73f576c04b94 ("mm: memcontrol: fix cgroup creation failure after many small jobs") Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current value for a target abort error is 0x010, however, this value
should in fact be 0x002. As it stands, the range of error is 0..7 so
it is currently never being detected. This bug has been in the driver
since the early 2.6.12 days (or before).
Detected by CoverityScan, CID#744290 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously in squashfs_readpage() when copying data into the page
cache, it used the length of the datablock read from the filesystem
(after decompression). However, if the filesystem has been corrupted
this data block may be short, which will leave pages unfilled.
The fix for this is to compute the expected number of bytes to copy
from the inode size, and use this to detect if the block is short.
Delete the old VM_BUG_ON_VMA() from zap_pmd_range(), which asserted
that mmap_sem must be held when splitting an "anonymous" vma there.
Whether that's still strictly true nowadays is not entirely clear,
but the danger of sometimes crashing on the BUG is now fairly clear.
Even with the new stricter rules for anonymous vma marking, the
condition it checks for can possible trigger. Commit 44960f2a7b63
("staging: ashmem: Fix SIGBUS crash when traversing mmaped ashmem
pages") is good, and originally I thought it was safe from that
VM_BUG_ON_VMA(), because the /dev/ashmem fd exposed to the user is
disconnected from the vm_file in the vma, and madvise(,,MADV_REMOVE)
insists on VM_SHARED.
But after I read John's earlier mail, drawing attention to the
vfs_fallocate() in there: I may be wrong, and I don't know if Android
has THP in the config anyway, but it looks to me like an
unmap_mapping_range() from ashmem's vfs_fallocate() could hit precisely
the VM_BUG_ON_VMA(), once it's vma_is_anonymous().
Anatoly continues to find issues with fuzzed squashfs images.
This time, corrupt, missing, or undersized data for the page filling
wasn't checked for, because the squashfs_{copy,read}_cache() functions
did the squashfs_copy_data() call without checking the resulting data
size.
Which could result in the page cache pages being incompletely filled in,
and no error indication to the user space reading garbage data.
So make a helper function for the "fill in pages" case, because the
exact same incomplete sequence existed in two places.
[ I should have made a squashfs branch for these things, but I didn't
intend to start doing them in the first place.
My historical connection through cramfs is why I got into looking at
these issues at all, and every time I (continue to) think it's a
one-off.
Because _this_ time is always the last time. Right? - Linus ]
In commit ab123fe071c9 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071c9 ("enic: handle mtu change for vf properly") Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to be able to include <linux/msi.h> when
CONFIG_GENERIC_MSI_IRQ_DOMAIN is enabled. Without this, a build with
CONFIG_GENERIC_MSI_IRQ_DOMAIN fails with:
In file included from drivers//ata/ahci.c:45:0:
>> include/linux/msi.h:226:10: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:230:9: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:239:12: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
msi_alloc_info_t *arg);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:240:22: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*msi_finish)(msi_alloc_info_t *arg, int retval);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:241:20: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
void (*set_desc)(msi_alloc_info_t *arg,
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:316:18: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
include/linux/msi.h:318:29: error: unknown type name 'msi_alloc_info_t'; did you mean 'sg_alloc_fn'?
int virq, int nvec, msi_alloc_info_t *args);
^~~~~~~~~~~~~~~~
sg_alloc_fn
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code that was added to force gcc not to inline any function that isn't
explicitly declared as inline uncovered that init_tick_ops() isn't
marked as "__init". It is only called by __init functions and more
importantly it too calls an __init function which would require it to be
__init as well.
Link: http://lkml.kernel.org/r/201806060444.hdHcKOBy%fengguang.wu@intel.com Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
../arch/arc/mm/cache.c: In function 'flush_anon_page':
../arch/arc/mm/cache.c:1062:55: warning: passing argument 2 of '__flush_dcache_page' makes integer from pointer without a cast [-Wint-conversion]
__flush_dcache_page((phys_addr_t)page_address(page), page_address(page));
^~~~~~~~~~~~~~~~~~
../arch/arc/mm/cache.c:1013:59: note: expected 'long unsigned int' but argument is of type 'void *'
void __flush_dcache_page(phys_addr_t paddr, unsigned long vaddr)
~~~~~~~~~~~~~~^~~~~
Fix build errors in arch/arc/'s delay.h:
- add "extern unsigned long loops_per_jiffy;"
- add <asm-generic/types.h> for "u64"
In file included from ../drivers/infiniband/hw/cxgb3/cxio_hal.c:32:
../arch/arc/include/asm/delay.h: In function '__udelay':
../arch/arc/include/asm/delay.h:61:12: error: 'u64' undeclared (first use in this function)
loops = ((u64) usecs * 4295 * HZ * loops_per_jiffy) >> 32;
^~~
In file included from ../drivers/infiniband/hw/cxgb3/cxio_hal.c:32:
../arch/arc/include/asm/delay.h: In function '__udelay':
../arch/arc/include/asm/delay.h:63:37: error: 'loops_per_jiffy' undeclared (first use in this function)
loops = ((u64) usecs * 4295 * HZ * loops_per_jiffy) >> 32;
^~~~~~~~~~~~~~~
Fix printk format warning in arch/arc/plat-eznps/mtm.c:
In file included from ../include/linux/printk.h:7,
from ../include/linux/kernel.h:14,
from ../include/linux/list.h:9,
from ../include/linux/smp.h:12,
from ../arch/arc/plat-eznps/mtm.c:17:
../arch/arc/plat-eznps/mtm.c: In function 'set_mtm_hs_ctr':
../include/linux/kern_levels.h:5:18: warning: format '%d' expects argument of type 'int', but argument 2 has type 'long int' [-Wformat=]
#define KERN_SOH "\001" /* ASCII Start Of Header */
^~~~~~
../include/linux/kern_levels.h:11:18: note: in expansion of macro 'KERN_SOH'
#define KERN_ERR KERN_SOH "3" /* error conditions */
^~~~~~~~
../include/linux/printk.h:308:9: note: in expansion of macro 'KERN_ERR'
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~
../arch/arc/plat-eznps/mtm.c:166:3: note: in expansion of macro 'pr_err'
pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
^~~~~~
../arch/arc/plat-eznps/mtm.c:166:40: note: format string is defined here
pr_err("** Invalid @nps_mtm_hs_ctr [%d] needs to be [%d:%d] (incl)\n",
~^
%ld
The hs_ctr variable can just be int instead of long, so also change
kstrtol() to kstrtoint() and leave the format string as %d.
Also add 2 header files since they are used in mtm.c and we prefer
not to depend on accidental/indirect #includes.
Cc: linux-snps-arc@lists.infradead.org Cc: Ofer Levi <oferle@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add <linux/types.h> to fix build errors.
Both ctop.h and <soc/nps/common.h> use u32 types and cause many
errors.
Examples:
../include/soc/nps/common.h:71:4: error: unknown type name 'u32'
u32 __reserved:20, cluster:4, core:4, thread:4;
../include/soc/nps/common.h:76:3: error: unknown type name 'u32'
u32 value;
../include/soc/nps/common.h:124:4: error: unknown type name 'u32'
u32 base:8, cl_x:4, cl_y:4,
../include/soc/nps/common.h:127:3: error: unknown type name 'u32'
u32 value;
../arch/arc/plat-eznps/include/plat/ctop.h:83:4: error: unknown type name 'u32'
u32 gen:1, gdis:1, clk_gate_dis:1, asb:1,
../arch/arc/plat-eznps/include/plat/ctop.h:86:3: error: unknown type name 'u32'
u32 value;
../arch/arc/plat-eznps/include/plat/ctop.h:93:4: error: unknown type name 'u32'
u32 csa:22, dmsid:6, __reserved:3, cs:1;
../arch/arc/plat-eznps/include/plat/ctop.h:95:3: error: unknown type name 'u32'
u32 value;
Cc: linux-snps-arc@lists.infradead.org Cc: Ofer Levi <oferle@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type. This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.
Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.
Fixes: 1025351a88a4 ("nfp: add flower app") Signed-off-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As for today we don't setup SMP_CACHE_BYTES and cache_line_size for
ARC, so they are set to L1_CACHE_BYTES by default. L1 line length
(L1_CACHE_BYTES) might be easily smaller than L2 line (which is
usually the case BTW). This breaks code.
For example this breaks ethernet infrastructure on HSDK/AXS103 boards
with IOC disabled, involving manual cache flushes
Functions which alloc and manage sk_buff packet data area rely on
SMP_CACHE_BYTES define. In the result we can share last L2 cache
line in sk_buff linear packet data area between DMA buffer and
some useful data in other structure. So we can lose this data when
we invalidate DMA buffer.
sk_buff linear packet data area
|
|
| skb->end skb->tail
V | |
V V
----------------------------------------------.
packet data | <tail padding> | <useful data in other struct>
----------------------------------------------.
---------------------.--------------------------------------------------.
SLC line | SLC (L2 cache) line (128B) |
---------------------.--------------------------------------------------.
^ ^
| |
These cache lines will be invalidated when we invalidate skb
linear packet data area before DMA transaction starting.
This leads to issues painful to debug as it reproduces only if
(sk_buff->end - sk_buff->tail) < SLC_LINE_SIZE and
if we have some useful data right after sk_buff->end.
Fix that by hardcode SMP_CACHE_BYTES to max line length we may have.
This reverts commit 2a027b47dba6 ("MIPS: BCM47XX: Enable 74K Core
ExternalSync for PCIe erratum").
Enabling ExternalSync caused a regression for BCM4718A1 (used e.g. in
Netgear E3000 and ASUS RT-N16): it simply hangs during PCIe
initialization. It's likely that BCM4717A1 is also affected.
I didn't notice that earlier as the only BCM47XX devices with PCIe I
own are:
1) BCM4706 with 2 x 14e4:4331
2) BCM4706 with 14e4:4360 and 14e4:4331
it appears that BCM4706 is unaffected.
While BCM5300X-ES300-RDS.pdf seems to document that erratum and its
workarounds (according to quotes provided by Tokunori) it seems not even
Broadcom follows them.
According to the provided info Broadcom should define CONF7_ES in their
SDK's mipsinc.h and implement workaround in the si_mips_init(). Checking
both didn't reveal such code. It *could* mean Broadcom also had some
problems with the given workaround.
This fixes the reported family on modern AMD processors (e.g. Ryzen,
which is family 0x17). Previously these processors all showed up as
family 0xf.
See the document
https://support.amd.com/TechDocs/56255_OSRR.pdf
section CPUID_Fn00000001_EAX for how to calculate the family
from the BaseFamily and ExtFamily values.
This matches the code in arch/x86/lib/cpu.c
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/sys/../zswap/stored_pages keeps rising in a zswap test with
"zswap.max_pool_percent=0" parameter. But it should not compress or
store pages any more since there is no space in the compressed pool.
Reproduce steps:
1. Boot kernel with "zswap.enabled=1"
2. Set the max_pool_percent to 0
# echo 0 > /sys/module/zswap/parameters/max_pool_percent
3. Do memory stress test to see if some pages have been compressed
# stress --vm 1 --vm-bytes $mem_available"M" --timeout 60s
4. Watching the 'stored_pages' number increasing or not
The root cause is:
When zswap_max_pool_percent is set to 0 via kernel parameter,
zswap_is_full() will always return true due to zswap_shrink(). But if
the shinking is able to reclain a page successfully the code then
proceeds to compressing/storing another page, so the value of
stored_pages will keep changing.
To solve the issue, this patch adds a zswap_is_full() check again after
zswap_shrink() to make sure it's now under the max_pool_percent, and to
not compress/store if we reached the limit.
Link: http://lkml.kernel.org/r/20180530103936.17812-1-liwang@redhat.com Signed-off-by: Li Wang <liwang@redhat.com> Acked-by: Dan Streetman <ddstreet@ieee.org> Cc: Seth Jennings <sjenning@redhat.com> Cc: Huang Ying <huang.ying.caritas@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for load/store tearing prevention to work, _all_ accesses to
the variable in question need to be done around READ and WRITE_ONCE()
macros. Ensure everyone does so for q->status variable for
semtimedop().
Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we meet a conflicting object that is marked FSCACHE_OBJECT_IS_LIVE in
the active object tree, we have been emitting a BUG after logging
information about it and the new object.
Instead, we should wait for the CACHEFILES_OBJECT_ACTIVE flag to be cleared
on the old object (or return an error). The ACTIVE flag should be cleared
after it has been removed from the active object tree. A timeout of 60s is
used in the wait, so we shouldn't be able to get stuck there.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") Signed-off-by: Kiran Kumar Modukuri <kiran.modukuri@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cachefiles_read_waiter() has the right to access a 'monitor' object by
virtue of being called under the waitqueue lock for one of the pages in its
purview. However, it has no ref on that monitor object or on the
associated operation.
What it is allowed to do is to move the monitor object to the operation's
to_do list, but once it drops the work_lock, it's actually no longer
permitted to access that object. However, it is trying to enqueue the
retrieval operation for processing - but it can only do this via a pointer
in the monitor object, something it shouldn't be doing.
If it doesn't enqueue the operation, the operation may not get processed.
If the order is flipped so that the enqueue is first, then it's possible
for the work processor to look at the to_do list before the monitor is
enqueued upon it.
Fix this by getting a ref on the operation so that we can trust that it
will still be there once we've added the monitor to the to_do list and
dropped the work_lock. The op can then be enqueued after the lock is
dropped.
The bug can manifest in one of a couple of ways. The first manifestation
looks like:
FS-Cache:
FS-Cache: Assertion failed
FS-Cache: 6 == 5 is false
------------[ cut here ]------------
kernel BUG at fs/fscache/operation.c:494!
RIP: 0010:fscache_put_operation+0x1e3/0x1f0
...
fscache_op_work_func+0x26/0x50
process_one_work+0x131/0x290
worker_thread+0x45/0x360
kthread+0xf8/0x130
? create_worker+0x190/0x190
? kthread_cancel_work_sync+0x10/0x10
ret_from_fork+0x1f/0x30
This is due to the operation being in the DEAD state (6) rather than
INITIALISED, COMPLETE or CANCELLED (5) because it's already passed through
fscache_put_operation().
Dirk Gouders reported that two consecutive "make" invocations on an
already compiled tree will show alternating behaviors:
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
DATAREL arch/x86/boot/compressed/vmlinux
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
$ make
CALL scripts/checksyscalls.sh
DESCEND objtool
CHK include/generated/compile.h
LD arch/x86/boot/compressed/vmlinux
ZOFFSET arch/x86/boot/zoffset.h
AS arch/x86/boot/header.o
LD arch/x86/boot/setup.elf
OBJCOPY arch/x86/boot/setup.bin
OBJCOPY arch/x86/boot/vmlinux.bin
BUILD arch/x86/boot/bzImage
Setup is 15644 bytes (padded to 15872 bytes).
System is 6663 kB
CRC 3eb90f40
Kernel: arch/x86/boot/bzImage is ready (#48)
Building modules, stage 2.
MODPOST 165 modules
He bisected it back to:
commit 98f78525371b ("x86/boot: Refuse to build with data relocations")
The root cause was the use of the "if_changed" kbuild function multiple
times for the same target. It was designed to only be used once per
target, otherwise it will effectively always trigger, flipping back and
forth between the two commands getting recorded by "if_changed". Instead,
this patch merges the two commands into a single function to get stable
build artifacts (i.e. .vmlinux.cmd), and a single build behavior.
NO_RT_RUNTIME_SHARE feature is used to prevent a CPU borrow enough
runtime with a spin-rt-task.
However, if RT_RUNTIME_SHARE feature is enabled and rt_rq has borrowd
enough rt_runtime at the beginning, rt_runtime can't be restored to
its initial bandwidth rt_runtime after we disable RT_RUNTIME_SHARE.
E.g. on my PC with 4 cores, procedure to reproduce:
1) Make sure RT_RUNTIME_SHARE is enabled
cat /sys/kernel/debug/sched_features
GENTLE_FAIR_SLEEPERS START_DEBIT NO_NEXT_BUDDY LAST_BUDDY
CACHE_HOT_BUDDY WAKEUP_PREEMPTION NO_HRTICK NO_DOUBLE_TICK
LB_BIAS NONTASK_CAPACITY TTWU_QUEUE NO_SIS_AVG_CPU SIS_PROP
NO_WARN_DOUBLE_CLOCK RT_PUSH_IPI RT_RUNTIME_SHARE NO_LB_MIN
ATTACH_AGE_LOAD WA_IDLE WA_WEIGHT WA_BIAS
2) Start a spin-rt-task
./loop_rr &
3) set affinity to the last cpu
taskset -p 8 $pid_of_loop_rr
4) Observe that last cpu have borrowed enough runtime.
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
5) Disable RT_RUNTIME_SHARE
echo NO_RT_RUNTIME_SHARE > /sys/kernel/debug/sched_features
6) Observe that rt_runtime can not been restored
cat /proc/sched_debug | grep rt_runtime
.rt_runtime : 950.000000
.rt_runtime : 900.000000
.rt_runtime : 950.000000
.rt_runtime : 1000.000000
This patch help to restore rt_runtime after we disable
RT_RUNTIME_SHARE.
The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).
Fixes: e7e197edd09c25 ("qmi_wwan: add support for the Dell Wireless 5821e module") Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10162 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(),
isa_virt_to_bus(), or isa_page_to_bus(), which are not available and
thus cause build errors.
../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open':
../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/lance.c: In function 'lance_rx':
../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance':
../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open':
../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD).
atl1c driver provided skb with no headroom, so 14 bytes (ethernet
header) got pulled, but then 16 are copied.
Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb().
Compile tested only; I lack hardware.
Fixes: 7b7017642199 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not expose the address of vmx->nested.current_vmptr to
kvm_write_guest_virt_system() as the resulting __copy_to_user()
call will trigger a WARN when CONFIG_HARDENED_USERCOPY is
enabled.
Opportunistically clean up variable names in handle_vmptrst()
to improve readability, e.g. vmcs_gva is misleading as the
memory operand of VMPTRST is plain memory, not a VMCS.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Tested-by: Peter Shier <pshier@google.com> Reviewed-by: Peter Shier <pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its possible to rename two chains to the same name in one
transaction:
nft add chain t c1
nft add chain t c2
nft 'rename chain t c1 c3;rename chain t c2 c3'
This creates two chains named 'c3'.
Appears to be harmless, both chains can still be deleted both
by name or handle, but, nevertheless, its a bug.
Walk transaction log and also compare vs. the pending renames.
Both chains can still be deleted, but nevertheless it is a bug as
we don't allow to create chains with identical names, so we should
prevent this from happening-by-rename too.
The new name is stored in the transaction metadata, on commit,
the pointers to the old and new names are swapped.
Therefore in abort and commit case we have to free the
pointer in the chain_trans container.
In commit case, the pointer can be used by another cpu that
is currently dumping the renamed chain, thus kfree needs to
happen after waiting for rcu readers to complete.
Fixes: b7263e071a ("netfilter: nf_tables: Allow chain name of up to 255 chars") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of the JITs is allowed to implement exit paths from the BPF
insn mappings other than BPF_JMP | BPF_EXIT. In the BPF core code
we have a couple of rewrites in eBPF (e.g. LD_ABS / LD_IND) and
in eBPF to cBPF translation to retain old existing behavior where
exceptions may occur; they are also tightly controlled by the
verifier where it disallows some of the features such as BPF to
BPF calls when legacy LD_ABS / LD_IND ops are present in the BPF
program. During recent review of all BPF_XADD JIT implementations
I noticed that the ppc64 one is buggy in that it contains two
jumps to exit paths. This is problematic as this can bypass verifier
expectations e.g. pointed out in commit f6b1b3bf0d5f ("bpf: fix
subprog verifier bypass by div/mod by 0 exception"). The first
exit path is obsoleted by the fix in ca36960211eb ("bpf: allow xadd
only on aligned memory") anyway, and for the second one we need to
do a fetch, add and store loop if the reservation from lwarx/ldarx
was lost in the meantime.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Reviewed-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Tested-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GC of set uses call_rcu() to destroy elements.
So that elements would be destroyed after destroying sets and chains.
But, elements should be destroyed before destroying sets and chains.
In order to wait calling call_rcu(), a rcu_barrier() is added.
In order to test correctly, below patch should be applied.
https://patchwork.ozlabs.org/patch/940883/
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbea6 ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b821168 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc7877 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac782 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0d2 ("ACM gadget: fix endianness in notifications")
commit 323ece54e076 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f1072 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tools/usb/ffs-test.c file defines cpu_to_le16/32 by using the C
library htole16/32 function calls. However, cpu_to_le16/32 are used when
initializing structures, i.e in a context where a function call is not
allowed.
It works fine on little endian systems because htole16/32 are defined by
the C library as no-ops. But on big-endian systems, they are actually
doing something, which might involve calling a function, causing build
failures, such as:
ffs-test.c:48:25: error: initializer element is not constant
#define cpu_to_le32(x) htole32(x)
^~~~~~~
ffs-test.c:128:12: note: in expansion of macro ‘cpu_to_le32’
.magic = cpu_to_le32(FUNCTIONFS_DESCRIPTORS_MAGIC_V2),
^~~~~~~~~~~
To solve this, we code cpu_to_le16/32 in a way that allows them to be
used when initializing structures. This fix was imported from
meta-openembedded/android-tools/fix-big-endian-build.patch written by
Thomas Petazzoni <thomas.petazzoni@free-electrons.com>.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
The change protects almost the whole body of u_audio_iso_complete()
function by PCM stream lock, this is mainly sufficient to avoid a race
between USB request completion and stream termination, the change
prevents a possibility of invalid memory access in interrupt context
by memcpy():
Also added a check for potential !runtime condition, commonly it is
done by PCM_RUNTIME_CHECK(substream) in the beginning, however this
does not completely prevent from oopses in u_audio_iso_complete(),
because the proper protection scheme must be implemented in PCM
library functions.
An example of *not fixed* oops due to substream->runtime->*
dereference by snd_pcm_running(substream) from
snd_pcm_period_elapsed(), where substream->runtime is gone while
waiting the substream lock:
Unable to handle kernel paging request at virtual address 6b6b6b6b
pgd = db7e4000
[6b6b6b6b] *pgd=00000000
CPU: 0 PID: 193 Comm: klogd Tainted: G C 3.14.54+ #118
task: db5ac500 ti: db60c000 task.ti: db60c000
PC is at snd_pcm_period_elapsed+0x48/0xd8 [snd_pcm]
LR is at snd_pcm_period_elapsed+0x40/0xd8 [snd_pcm]
pc : [<>] lr : [<>] psr: 60000193
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 2b7e404a DAC: 00000015
Process klogd (pid: 193, stack limit = 0xdb60c238)
[<>] (snd_pcm_period_elapsed [snd_pcm]) from [<>] (udc_irq+0x500/0xbbc)
[<>] (udc_irq) from [<>] (ci_irq+0x280/0x304)
[<>] (ci_irq) from [<>] (handle_irq_event_percpu+0xa4/0x40c)
[<>] (handle_irq_event_percpu) from [<>] (handle_irq_event+0x3c/0x5c)
[<>] (handle_irq_event) from [<>] (handle_fasteoi_irq+0xc4/0x110)
[<>] (handle_fasteoi_irq) from [<>] (generic_handle_irq+0x20/0x30)
[<>] (generic_handle_irq) from [<>] (handle_IRQ+0x80/0xc0)
[<>] (handle_IRQ) from [<>] (gic_handle_irq+0x3c/0x60)
[<>] (gic_handle_irq) from [<>] (__irq_svc+0x44/0x78)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
[erosca: W/o this patch, with minimal instrumentation [1], I can
consistently reproduce BUG: KASAN: use-after-free [2]]
[1] Instrumentation to reproduce issue [2]:
# diff --git a/drivers/usb/gadget/function/u_audio.c b/drivers/usb/gadget/function/u_audio.c
# index a72295c953bb..bd0b308024fe 100644
# --- a/drivers/usb/gadget/function/u_audio.c
# +++ b/drivers/usb/gadget/function/u_audio.c
# @@ -16,6 +16,7 @@
# #include <sound/core.h>
# #include <sound/pcm.h>
# #include <sound/pcm_params.h>
# +#include <linux/delay.h>
#
# #include "u_audio.h"
#
# @@ -147,6 +148,8 @@ static void u_audio_iso_complete(struct usb_ep *ep, struct usb_request *req)
#
# spin_unlock_irqrestore(&prm->lock, flags);
#
# + udelay(500); //delay here to increase probability of parallel activities
# +
# /* Pack USB load in ALSA ring buffer */
# pending = prm->dma_bytes - hw_ptr;
[2] After applying [1], below BUG occurs on Rcar-H3-Salvator-X board:
==================================================================
BUG: KASAN: use-after-free in u_audio_iso_complete+0x24c/0x520 [u_audio]
Read of size 8 at addr ffff8006cafcc248 by task swapper/0/0
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb460839 ("usb: gadget: Add Audio Class 2.0 Driver") Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In u_audio_iso_complete, the runtime hw_ptr is updated before the
data is actually copied over to/from the buffer/dma area. When
ALSA uses this hw_ptr, the data may not actually be available to
be used. This causes trash/stale audio to play/record. This
patch updates the hw_ptr after the data has been copied to avoid
this.
Fix below smatch (v0.5.0-4443-g69e9094e11c1) warnings:
drivers/usb/gadget/function/u_audio.c:607 g_audio_setup() warn: strcpy() 'pcm_name' of unknown size might be too large for 'pcm->name'
drivers/usb/gadget/function/u_audio.c:614 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->driver'
drivers/usb/gadget/function/u_audio.c:615 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->shortname'
Below commits performed a similar 's/strcpy/strlcpy/' rework:
* v2.6.31 commit 8372d4980fbc ("ALSA: ctxfi - Fix PCM device naming")
* v4.14 commit 003d3e70dbeb ("ALSA: ad1848: fix format string overflow warning")
* v4.14 commit 6d8b04de87e1 ("ALSA: cs423x: fix format string overflow warning")
If usb_ep_autoconfig() fails (i.e. returns a null endpoint descriptor),
we expect afunc_bind() to fail (i.e. return a negative error code).
However, due to v4.10-rc1 commit f1d3861d63a5 ("usb: gadget: f_uac2: fix
error handling at afunc_bind"), afunc_bind() returns zero, telling the
caller that it succeeded. This then generates NULL pointer dereference
in below scenario on Rcar H3-ES20-Salvator-X target:
After this patch is applied, the issue is fixed:
rcar-gen3:/home/root# modprobe g_audio
[ 59.217127] g_audio gadget: afunc_bind:565 Error!
[ 59.222329] g_audio ee020000.usb: failed to start g_audio: -19
modprobe: ERROR: could not insert 'g_audio': No such device
rcar-gen3:/home/root# modprobe -r g_audio
rcar-gen3:/home/root#
If the server or network is misbehaving and we get an unexpected reply
we can sometimes miss the request not being started and wait on a
request and never get a response, or even double complete the same
request. Fix this by replacing the send_complete completion with just a
per command lock. Add a per command cookie as well so that we can know
if we're getting a double completion for a previous event. Also check
to make sure we dont have REQUEUED set as that means we raced with the
timeout handler and need to just let the retry occur.
We can race with the snd timeout and the per-request timeout and end up
requeuing the same request twice. We can't use the send_complete
completion to tell if everything is ok because we hold the tx_lock
during send, so the timeout stuff will block waiting to mark the socket
dead, and we could be marked complete and still requeue. Instead add a
flag to the socket so we know whether we've been requeued yet.
The LVDS signal integrity is only guaranteed when the correct enable
sequence (first IPU DI, then LDB) is used. If the LDB display output was
active before the imx-drm driver is loaded (like when a bootsplash was
active) the DI will be disabled by the full IPU reset we do when loading
the driver. The LDB control registers are not part of the IPU range and
thus will remain unchanged.
This leads to the LDB still being active when the DI is getting enabled,
effectively reversing the required enable sequence. Fix this by also
disabling the LDB on driver bind.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transport drivers allocate memory for iSCSI hdr in alloc_pdu() and assign
it to task->hdr. In case of TMF task->hdr will be NULL resulting in NULL
pointer dereference.
2. ISCSI_OP_SCSI_DATA_OUT - In this case transport driver can free the
memory for iSCSI hdr after transmitting the pdu so task->hdr can be NULL or
invalid.
This patch fixes this issue by removing task->hdr->opcode from the printk
statement.
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com> Tested-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Archit Taneja <architt@codeaurora.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was looking at usually suppressed gcc warnings,
[-Wimplicit-fallthrough=] in this case:
The code definitely looks like a break is missing here.
However I am not able to test the NL80211_IFTYPE_MESH_POINT,
nor do I actually know what might be :)
So please use this patch with caution and only if you are
able to do some testing.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
[johannes: looks obvious enough to apply as is, interesting
though that it never seems to have been a problem] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, when an MMP-protected file system is remounted read-only,
the kmmpd thread would exit the next time it woke up (a few seconds
later), without resetting the MMP sequence number back to
EXT4_MMP_SEQ_CLEAN.
Fix this by explicitly killing the MMP thread when the file system is
remounted read-only.
As part of hw reconfig, only stations linked to AP interfaces are added
back to the driver ignoring those which are tied to AP_VLAN interfaces.
It is true that there could be stations tied to the AP_VLAN interface while
serving 4addr clients or when using AP_VLAN for VLAN operations; we should
be adding these stations back to the driver as part of hw reconfig, failing
to do so can cause functional issues.
In the case of ath10k driver, the following errors were observed.
This ought to be an omission in e6194923237 ("esp: Fix memleaks on error
paths."). The memleak on error path in esp6_input is similar to esp_input
of esp4.
Fixes: e6194923237 ("esp: Fix memleaks on error paths.") Fixes: 3f29770723f ("ipsec: check return value of skb_to_sgvec always") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix missing dst_release() when local broadcast or multicast traffic is
xfrm policy blocked.
For IPv4 this results to dst leak: ip_route_output_flow() allocates
dst_entry via __ip_route_output_key() and passes it to
xfrm_lookup_route(). xfrm_lookup returns ERR_PTR(-EPERM) that is
propagated. The dst that was allocated is never released.
IPv4 local broadcast testcase:
ping -b 192.168.1.255 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 192.168.1.255/32 dir out action block
IPv4 multicast testcase:
ping 224.0.0.1 &
sleep 1
ip xfrm policy add src 0.0.0.0/0 dst 224.0.0.1/32 dir out action block
For IPv6 the missing dst_release() causes trouble e.g. when used in netns:
ip netns add TEST
ip netns exec TEST ip link set lo up
ip link add dummy0 type dummy
ip link set dev dummy0 netns TEST
ip netns exec TEST ip addr add fd00::1111 dev dummy0
ip netns exec TEST ip link set dummy0 up
ip netns exec TEST ping -6 -c 5 ff02::1%dummy0 &
sleep 1
ip netns exec TEST ip xfrm policy add src ::/0 dst ff02::1 dir out action block
wait
ip netns del TEST
After netns deletion we see:
[ 258.239097] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 268.279061] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 278.367018] unregister_netdevice: waiting for lo to become free. Usage count = 2
[ 288.375259] unregister_netdevice: waiting for lo to become free. Usage count = 2
Fixes: ac37e2515c1a ("xfrm: release dst_orig in case of error in xfrm_lookup()") Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- When a buffer size is supplied to reiserfs_listxattr() such that each
individual name fits, but the concatenation of all names doesn't fit,
reiserfs_listxattr() overflows the supplied buffer. This leads to a
kernel heap overflow (verified using KASAN) followed by an out-of-bounds
usercopy and is therefore a security bug.
- When a buffer size is supplied to reiserfs_listxattr() such that a
name doesn't fit, -ERANGE should be returned. But reiserfs instead just
truncates the list of names; I have verified that if the only xattr on a
file has a longer name than the supplied buffer length, listxattr()
incorrectly returns zero.
With my patch applied, -ERANGE is returned in both cases and the memory
corruption doesn't happen anymore.
Credit for making me clean this code up a bit goes to Al Viro, who pointed
out that the ->actor calling convention is suboptimal and should be
changed.
Link: http://lkml.kernel.org/r/20180802151539.5373-1-jannh@google.com Fixes: 48b32a3553a5 ("reiserfs: use generic xattr handlers") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: Jeff Mahoney <jeffm@suse.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.
This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug
events for a device") iterates over the devices on a hotplug port's
subordinate bus in pciehp's IRQ handler without acquiring pci_bus_sem.
It is thus possible for a user to cause a crash by concurrently
manipulating the device list, e.g. by disabling slot power via sysfs
on a different CPU or by initiating a remove/rescan via sysfs.
This can't be fixed by acquiring pci_bus_sem because it may sleep.
The simplest fix is to avoid the list iteration altogether and just
check the ignore_hotplug flag on the port itself. This works because
pci_ignore_hotplug() sets the flag both on the device as well as on its
parent bridge.
We do lose the ability to print the name of the device blocking hotplug
in the debug message, but that's probably bearable.
Fixes: b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device") Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
PCIe r4.0, sec 9.3.5.4, "Device Control Register", shows both
Max_Payload_Size (MPS) and Max_Read_request_Size (MRRS) to be 'RsvdP' for
VFs. Just prior to the table it states:
"PF and VF functionality is defined in Section 7.5.3.4 except where
noted in Table 9-16. For VF fields marked 'RsvdP', the PF setting
applies to the VF."
All of which implies that with respect to Max_Payload_Size Supported
(MPSS), MPS, and MRRS values, we should not be paying any attention to the
VF's fields, but rather only to the PF's. Only looking at the PF's fields
also logically makes sense as it's the sole physical interface to the PCIe
bus.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527 Fixes: 27d868b5e6cf ("PCI: Set MPS to match upstream bridge") Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org # 4.3+ Cc: Keith Busch <keith.busch@intel.com> Cc: Sinan Kaya <okaya@kernel.org> Cc: Dongdong Liu <liudongdong3@huawei.com> Cc: Jon Mason <jdmason@kudzu.us> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If addition of sysfs files fails on registration of a hotplug slot, the
struct pci_slot as well as the entry in the slot_list is leaked. The
issue has been present since the hotplug core was introduced in 2002:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Perhaps the idea was that even though sysfs addition fails, the slot
should still be usable. But that's not how drivers use the interface,
they abort probe if a non-zero value is returned.
Now that mb() is an instruction barrier, it will slow performance if we issue
unnecessary barriers.
The spinlock defines have a number of unnecessary barriers. The __ldcw()
define is both a hardware and compiler barrier. The mb() barriers in the
routines using __ldcw() serve no purpose.
The only barrier needed is the one in arch_spin_unlock(). We need to ensure
all accesses are complete prior to releasing the lock.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 4.0+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoking shutdown for a socket in state SMC_LISTEN does not make
sense. Nevertheless programs like syzbot fuzzing the kernel may
try to do this. For SMC this means a socket refcounting problem.
This patch makes sure a shutdown call for an SMC socket in state
SMC_LISTEN simply returns with -ENOTCONN.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.") Fixes: eb73190f4fbe ("net/packet: refine check for priv area size") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When first DCCP packet is SYNC or SYNCACK, we insert a new conntrack
that has an un-initialized timeout value, i.e. such entry could be
reaped at any time.
Mark them as INVALID and only ignore SYNC/SYNCACK when connection had
an old state.
Now that we use a sync prior to releasing the locks in syscall.S, we don't need
the PA 2.0 ordered stores used to release some locks. Using an ordered store,
potentially slows the release and subsequent code.
There are a number of other ordered stores and loads that serve no purpose. I
have converted these to normal stores.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 4.0+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IMPORTANT: if you fix the bug, please add the following tag to the commit: Reported-by: syzbot+bf9253040425feb155ad@syzkaller.appspotmail.com
It will help syzbot understand when the bug is fixed. See footer for details.
If you forward the report, please keep this part and the footer.
A comment warning against this bug is there, but the code is not doing what
the comment says. Therefore it is possible that an EPOLLHUP races against
irq_bypass_register_consumer. The EPOLLHUP handler schedules irqfd_shutdown,
and if that runs soon enough, you get a use-after-free.
The old code in nvme_user_cmd() passed the userspace virtual address
from nvme_passthru_cmd.metadata as the length of the metadata buffer
as well as the address to nvme_submit_user_cmd().
Fixes: 63263d60 ("nvme: Use metadata for passthrough commands") Signed-off-by: Roland Dreier <roland@purestorage.com> Reviewed-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
The ec_no_wakeup matcher added for Thinkpad X1 Carbon 6th gen systems
beyond matched only a single DMI model (20KGS3JF01), that didn't cover
my laptop (20KH002JUS). Change to match based on DMI product family to
cover all X1 6th gen systems.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPC registers are NOT continuous, some registers are
reserved and accessing them from userspace will trigger
external abort, add regmap register access table to
avoid below abort:
root@imx6slevk:~# cat /sys/kernel/debug/regmap/20dc000.gpc/registers
[ 108.480477] Unhandled fault: imprecise external abort (0x1406) at 0xb6db5004
[ 108.487985] pgd = 42b54bfd
[ 108.490741] [b6db5004] *pgd=ba1b7831
[ 108.494386] Internal error: : 1406 [#1] SMP ARM
[ 108.498943] Modules linked in:
[ 108.502043] CPU: 0 PID: 389 Comm: cat Not tainted 4.18.0-rc1-00074-gc9f1f60-dirty #482
[ 108.509982] Hardware name: Freescale i.MX6 SoloLite (Device Tree)
[ 108.516123] PC is at regmap_mmio_read32le+0x20/0x24
[ 108.521031] LR is at regmap_mmio_read+0x40/0x60
[ 108.525586] pc : [<c059cf74>] lr : [<c059d1ac>] psr: 20060093
[ 108.531875] sp : eccf1d98 ip : eccf1da8 fp : eccf1da4
[ 108.537122] r10: ec2d3800 r9 : eccf1f60 r8 : ecfc0000
[ 108.542370] r7 : eccf1e2c r6 : eccf1e2c r5 : 00000028 r4 : ec338e00
[ 108.548920] r3 : 00000000 r2 : eccf1e2c r1 : f0980028 r0 : 00000000
[ 108.555474] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
[ 108.562720] Control: 10c5387d Table: acf4004a DAC: 00000051
[ 108.568491] Process cat (pid: 389, stack limit = 0xd4318a65)
[ 108.574174] Stack: (0xeccf1d98 to 0xeccf2000)
Fixes: 721cabf6c660 ("soc: imx: move PGC handling to a new GPC driver") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempt to make cryptic TCP seq number error messages clearer by
(1) identifying the source of the message as "TCP", (2) identifying the
errors as "seq # bug", and (3) grouping the field identifiers and values
by separating them with commas.
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases the probing fails the log level of the messages should
be an error.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log