Add helper rdev_to_drm(rdev), similar to amdgpu, most function should
access the "drm_device" with "rdev_to_drm(rdev)" instead, where amdgpu has
"adev_to_drm(adev)". It also makes changing from "*drm_device" to "drm_device"
in "radeon_devicce" later on easier.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Tested-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Wu Hoi Pok <wuhoipok@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Remove unnecessary DSC power gating for DCN401
[Why]
In some cases during topology changes, a pipe that was used to drive a
stream being removed can be re-assigned to drive a different stream. In
these cases, DSC power gating is not handled properly, leading to
situations where DSC is being setup while power gated.
[How]
- remove enable_stream_gating and disable_stream_gating for DCN401
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Joshua Aberback <joshua.aberback@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Duncan Ma [Thu, 27 Jun 2024 16:11:58 +0000 (12:11 -0400)]
drm/amd/display: Add visual confirm for Idle State
[Why]
Visual Confirm would tell us if it ever
entered idle state.
[How]
Add debug option for IPS visual confirm
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Duncan Ma <duncan.ma@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel Sa [Thu, 4 Jul 2024 17:41:15 +0000 (13:41 -0400)]
drm/amd/display: Set Cursor Matrix to bypass instead of Input Plane
why:
When the cursor disappears/reappears on fullscreen video, there is a
short transitional period where the cursor's color matrix is using the
same format as the video plane. This sets the cursor to the wrong color
momentarily before the UI plane appears, correcting the color.
how:
Instead of defaulting to using the color space from the input plane,
default to bypass mode.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Daniel Sa <daniel.sa@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Check stream pointer is initialized before accessing
[why & how]
We calculate static screen wait frames based
on the current timing info in the active stream.
If stream is not initialized, then we should skip
the calculation and go with the default values.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Export additional FAMS2 global configuration options from DML
[WHY&HOW]
Some global configuration options were previously hardcoded in DC, now they are
exported by DML and sent to FW.
Reviewed-by: Martin Leung <martin.leung@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Dillon Varone <dillon.varone@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Refactoring DWB related files from dcn30 Files
[Why]
To refactor DWB related files from dcn30 Files
[How]
Moved DWB related files from dcn30 to specific DWB folder and
updated Makefiles to fix Compilation.
Reviewed-by: Martin Leung <martin.leung@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Mudimela <lmudimel@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Wed, 3 Jul 2024 16:50:35 +0000 (10:50 -0600)]
drm/amd/display: Increase array size of dummy_boolean
[WHY]
dml2_core_shared_mode_support and dml_core_mode_support access the third
element of dummy_boolean, i.e. hw_debug5 = &s->dummy_boolean[2], when
dummy_boolean has size of 2. Any assignment to hw_debug5 causes an
OVERRUN.
[HOW]
Increase dummy_boolean's array size to 3.
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Tue, 25 Jun 2024 16:37:35 +0000 (10:37 -0600)]
drm/amd/display: Check null pointers before multiple uses
[WHAT & HOW]
Poniters, such as stream_enc and dc->bw_vbios, are null checked previously
in the same function, so Coverity warns "implies that stream_enc and
dc->bw_vbios might be null". They are used multiple times in the
subsequent code and need to be checked.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Tue, 25 Jun 2024 16:35:52 +0000 (10:35 -0600)]
drm/amd/display: Check null pointers before used
[WHAT & HOW]
Poniters, such as dc->clk_mgr, are null checked previously in the same
function, so Coverity warns "implies that "dc->clk_mgr" might be null".
As a result, these pointers need to be checked when used again.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Thu, 27 Jun 2024 22:45:39 +0000 (16:45 -0600)]
drm/amd/display: Check link_res->hpo_dp_link_enc before using it
[WHAT & HOW]
Functions dp_enable_link_phy and dp_disable_link_phy can pass link_res
without initializing hpo_dp_link_enc and it is necessary to check for
null before dereferencing.
This fixes 2 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add P-State Keepout to dcn401 Global Sync
[WHY&HOW]
OTG has new functionality to allow P-State relative to VStartup. Keepout region
for this should be configured based on DML outputs same as other global sync
params.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Dillon Varone <dillon.varone@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Samson Tam [Wed, 3 Jul 2024 16:23:02 +0000 (12:23 -0400)]
drm/amd/display: remove dc dependencies from SPL library
[Why]
Make SPL library dc-independent so it can be reused by other
components
[How]
Create separate set of fixed31_32 calls in SPL
Make all inputs and outputs to SPL use primitive types
For ratios and inits, return as uint32 from SPL. So
add conversion from uint32 back to fixed point in
SPL-to-dc translate function
Reviewed-by: Relja Vojvodic <relja.vojvodic@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Samson Tam <samson.tam@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Issue with 3 or more mcaches per surface
[Why & How]
Current logic in mcache admissibility check has flaw if
calculated number of maches are 3 or more per surface,
so sometimes the check may pass when it should fail,
and sometimes may fail when it should pass, fix the
issue and also adding additional check to make sure that
required number of mcaches per surface cannot be
higher than number of pipes + 1, used on that surface.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Nevenko Stupar <nevenko.stupar@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Wed, 3 Jul 2024 15:36:34 +0000 (11:36 -0400)]
drm/amd/display: Calculate ODM width using odm slice rect, not recout
[Description]
There are scenarios where ODM4:1 is used but the
surface is entirely outside of the first and last
ODM slice. In this case the recout.width for the
first and last slice is 0 because there's no overlap
with the surface and that ODM slice, but this causes
the x_pos for the cursor in this scenario to be
calculated incorrectly. Instead we should use the
ODM slice width instead of the recout width.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add blanked streams override to DML2.1
[WHY]
DML2.1 currently has no concept of a "blanked" stream. For cases like DPMS off,
things like UCLK p-state is always allowed, so PMO is not required to optimize
for it.
[HOW]
Add flag to DML2.1 display configuration to indicate all streams are blanked,
so certain operations and optimizations can be skipped for optimal programming
when displays are blanked.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Dillon Varone <dillon.varone@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tom Chung [Wed, 3 Jul 2024 08:47:57 +0000 (16:47 +0800)]
drm/amd/display: Fix VRR cannot enable
[Why]
Sometimes the VRR cannot enable after login to the desktop.
User space may call the DRM_IOCTL_MODE_GETCONNECTOR right after
the DRM_IOCTL_MODE_RMFB.
After calling DRM_IOCTL_MODE_RMFB to remove all the frame buffer
and it will cause the driver to disable the crtc and disable the
link while calling the link_set_dpms_off().
It will cause the dpcd read failed in amdgpu_dm_update_freesync_caps()
while try to get the DP_MSA_TIMING_PAR_IGNORED capability and think
the sink side does not support VRR.
[How]
Use the dpcd_caps.allow_invalid_MSA_timing_param flag instead of
reading from dpcd directly.
dpcd_caps.allow_invalid_MSA_timing_param flag is updated during HPD.
It is safe to replace the original method.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mounika Adhuri [Wed, 26 Jun 2024 13:21:04 +0000 (18:51 +0530)]
drm/amd/display: Refactoring MPC
[Why]
To refactor MPC files
[How]
Moved MPC files to respective folders and
updated makefiles appropriately.
Reviewed-by: Martin Leung <martin.leung@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Mounika Adhuri <moadhuri@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Do 1-to-1 mapping between OPP and DSC in DML2
[why]
To determine which block instance to power-gate,
we look at the available pipe resource for both plane
and stream. On MPO, DSC3 was falsely powered on even
though only 1 stream path was enabled because
the resource mapping was not done correctly.
[how]
Acquire the correct DSC instance to power on / off based
on the instance of OPP which determines the backend
pipe index.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Moved mmhubbub files from dcn20 to /mmhubbub/ folder and
update makefile to fix compilation.
Reviewed-by: Martin Leung <martin.leung@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Revalla Hari Krishna <harikrishna.revalla@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chris Park [Fri, 28 Jun 2024 19:09:06 +0000 (15:09 -0400)]
drm/amd/display: Deallocate DML memory if allocation fails
[Why]
When DC state create DML memory allocation fails, memory is not
deallocated subsequently, resulting in uninitialized structure
that is not NULL.
[How]
Deallocate memory if DML memory allocation fails.
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Chris Park <chris.park@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Fri, 28 Jun 2024 02:05:14 +0000 (20:05 -0600)]
drm/amd/display: Check stream before comparing them
[WHAT & HOW]
amdgpu_dm can pass a null stream to dc_is_stream_unchanged. It is
necessary to check for null before dereferencing them.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Thu, 27 Jun 2024 23:38:16 +0000 (17:38 -0600)]
drm/amd/display: Check null pointers before using them
[WHAT & HOW]
These pointers are null checked previously in the same function,
indicating they might be null as reported by Coverity. As a result,
they need to be checked when used again.
This fixes 3 FORWARD_NULL issue reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Thu, 27 Jun 2024 17:51:27 +0000 (11:51 -0600)]
drm/amd/display: Pass non-null to dcn20_validate_apply_pipe_split_flags
[WHAT & HOW]
"dcn20_validate_apply_pipe_split_flags" dereferences merge, and thus it
cannot be a null pointer. Let's pass a valid pointer to avoid null
dereference.
This fixes 2 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Fri, 21 Jun 2024 02:23:41 +0000 (20:23 -0600)]
drm/amd/display: Check phantom_stream before it is used
dcn32_enable_phantom_stream can return null, so returned value
must be checked before used.
This fixes 1 NULL_RETURNS issue reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Thu, 27 Jun 2024 23:34:18 +0000 (17:34 -0600)]
drm/amd/display: Check null-initialized variables
[WHAT & HOW]
drr_timing and subvp_pipe are initialized to null and they are not
always assigned new values. It is necessary to check for null before
dereferencing.
This fixes 2 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com> Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Tue, 18 Jun 2024 20:05:08 +0000 (14:05 -0600)]
drm/amd/display: Initialize denominators' default to 1
[WHAT & HOW]
Variables used as denominators and maybe not assigned to other values,
should not be 0. Change their default to 1 so they are never 0.
This fixes 10 DIVIDE_BY_ZERO issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Gabe Teeger [Fri, 28 Jun 2024 20:05:36 +0000 (16:05 -0400)]
drm/amd/display: Fix DP-DVI dongle hotplug
[why]
Hotplugging with a DVI-DP dongle on pre-rdna embedded platform
working about half the time. The regression was found to be the
setting of link->type here.
[what]
Reverts fix besides the logging added.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Gabe Teeger <gabe.teeger@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Thu, 27 Jun 2024 15:56:47 +0000 (11:56 -0400)]
drm/amd/display: Disable subvp based on HW cursor requirement
[Description]
- There are situations where HW cursor is required
- In these scenarios we should disable subvp based on the HW cursor
requirement
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Thu, 27 Jun 2024 14:42:26 +0000 (10:42 -0400)]
drm/amd/display: When resync fifo ensure to use correct pipe ctx
We resync the FIFO after each pipe update in apply_ctx_to_hw.
However, this means that some pipes (in hardware) are based on the
new context and some are based on the current_state (since the pipes
are updated on at a time). In this case we must ensure to use the
pipe_ctx that's currently still configured in hardware when turning
off / on OTG's and reconfiguring ODM during the resync.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sridevi Arvindekar [Thu, 27 Jun 2024 13:39:33 +0000 (09:39 -0400)]
drm/amd/display: Add option to allow transition when odm is forced
Added option to allow transition for forced odm.
Add the variation to the nightly run.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Sridevi Arvindekar <sarvinde@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jingwen Zhu [Tue, 25 Jun 2024 08:20:58 +0000 (16:20 +0800)]
drm/amd/display: avoid disable otg when dig was disabled
[Why]
This is a workaround for an dcn3.1 hang that happens if otg dispclk
is ramped while otg is on and stream enc is off.
But this w/a should not trigger when we have a dig active.
[How]
Avoid disable otg when dig FE/BE FIFO was not switched.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Jingwen Zhu <jingwen.zhu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Relja Vojvodic [Thu, 27 Jun 2024 21:41:36 +0000 (17:41 -0400)]
drm/amd/display: Implement bias and scale pre scl
why:
New scaler needs the input to be full range color space. This will also fix
issues that come up due to not having a predefined limited color space matrix
for certain color spaces
how:
Use bias and scale HW to expand the range of limited color spaces to full
before the scaler
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Fri, 31 May 2024 15:37:15 +0000 (11:37 -0400)]
drm/amd/display: apply vmin optimization even if it doesn't reach vmin level
[why]
Based on power measurement result, in most cases when display clock is higher
than Vmin display clock, lowering display clock using dynamic ODM will improve
overall power consumption by 0 to 4 watts even if we can't reach Vmin.
[how]
Allow vmin optimization applied even if dispclk can't reach Vmin.
Reviewed-by: Jun Lei <jun.lei@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Tue, 25 Jun 2024 19:22:25 +0000 (15:22 -0400)]
drm/amd/display: fix dscclk programming sequence on DCN401
[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Reviewed-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It happens when LTTPRs fail to increment dpcd repeater count.
We have a recovery action in place for such cases.
Assert is misleading, an indicative error in dmesg is more useful.
[How]
Remove ASSERT and use DC_LOG_ERROR instead.
Reviewed-by: Michael Strauss <michael.strauss@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ryan Seto [Wed, 26 Jun 2024 18:53:26 +0000 (14:53 -0400)]
drm/amd/display: Added logging for automated DPM testing
[Why]
Added clock logs to automate DPM testing
[How]
Added logs and helper functions to output clocks
Co-authored-by: Ryan Seto <ryanseto@amd.com> Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Ryan Seto <ryanseto@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Tue, 25 Jun 2024 20:40:51 +0000 (16:40 -0400)]
drm/amd/display: Don't consider cursor for no plane case in DML1
[Description]
For no plane scenarios we should not consider cursor as there cannot
be any cursor if there's no planes. This fixes an issue where
dc_commit_streams fails due to prefetch bandwidth requirements
(the display config + dummy planes + cursor causes the prefetch
bandwidth to exceed what is possible).
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Samson Tam [Thu, 20 Jun 2024 19:42:45 +0000 (15:42 -0400)]
drm/amd/display: quality improvements for EASF and ISHARP
[Why]
Update coefficients and LUT tables for scaler and sharpener
to improve quality and support different use cases (SDR/HDR)
[How]
Move scaler coefficients to new file dc_spl_scl_easf_filters.c
Remove older coefficients file dc_sp_scl_filters_old.c
Update default taps for EASF support
Update LLS policy for DON'T CARE case
Update cositing offset from 0.5 to 0.25
Add support to adjust sharpness based on level, use case,
and scaling ratio ( using discrete levels )
Apply sharpness to all RGB surfaces and both NV12 and P010
video ( in fullscreen only ). Upscale and 1:1 ratios only
Enable scaler when sharpening 1:1 ratios
Add support for coefficients that are in S1.10 format
(convert to S1.12 format)
Reviewed-by: Jun Lei <jun.lei@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Samson Tam <samson.tam@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Tue, 12 Sep 2023 18:51:47 +0000 (14:51 -0400)]
drm/amd/display: Disable HBR audio for DP2 for certain ASICs
[Description]
Due to a HW bug, HBR audio is not supported for
DP2 encoders for certain ASICs.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tom Chung [Wed, 26 Jun 2024 08:14:24 +0000 (16:14 +0800)]
drm/amd/display: Disable replay if VRR capability is false
[Why]
The VRR need to be supported for panel replay feature.
If VRR capability is false, panel replay capability also
need to be disabled.
[How]
After update the vrr capability, the panel replay capability
also need to be check if need.
Reviewed-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Matthew Brost [Tue, 16 Jul 2024 06:39:01 +0000 (23:39 -0700)]
drm/xe: Wedge the entire device
Wedge the entire device, not just GT which may have triggered the wedge.
To implement this, cleanup the layering so xe_device_declare_wedged()
calls into the lower layers (GT) to ensure entire device is wedged.
While we are here, also signal any pending GT TLB invalidations upon
wedging device.
Lastly, short circuit reset wait if device is wedged.
v2:
- Short circuit reset wait if device is wedged (Local testing)
Michal Wajdeczko [Thu, 11 Jul 2024 19:23:19 +0000 (21:23 +0200)]
drm/xe/pf: Limit fair VF LMEM provisioning
Due to the current design of the BO and VRAM manager, any object
with XE_BO_FLAG_PINNED flag, which the PF driver uses during VF
LMEM provisionining, is created with the TTM_PL_FLAG_CONTIGUOUS
flag, which may cause VRAM fragmentation that prevents subsequent
allocations of larger objects, like fair VF LMEM provisioning.
To avoid such failures, round down fair VF LMEM provisioning size
to next power of two size, to compensate what xe_ttm_vram_mgr is
doing to achieve contiguous allocations.
Documentation/gpu/amdgpu/display/display-manager:134:
drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:3: WARNING: Duplicate C
declaration, also defined at gpu/amdgpu/display/dcn-blocks:101.
Declaration is '.. c:struct:: mpcc_blnd_cfg'.
Documentation/gpu/amdgpu/display/display-manager:146:
drivers/gpu/drm/amd/display/dc/inc/hw/mpc.h:3: WARNING: Duplicate C
declaration, also defined at gpu/amdgpu/display/dcn-blocks:3.
Declaration is '.. c:enum:: mpcc_alpha_blend_mode'.
To address the above warnings, this commit uses the 'no-identifiers'
option in the dcn-blocks to avoid duplication with the previous use of
this function doc in the display-manager file. Finally, replaces the
deprecated ':function:' in favor of ':identifiers:'.
Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Documentation/gpu: Remove undocumented files from dcn-blockshubbub.h
The dchubbub.h and hubp.h do not have any meaningful documentation; for
this reason, this commit removes those files from the dcn-blocks
documentation.
Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Add simple struct doc to remove doc build warning
This commit is a part of a series that addresses the following build
warning for opp:
./drivers/gpu/drm/amd/display/dc/inc/hw/opp.h:1: warning: no structured
comments found
./drivers/gpu/drm/amd/display/dc/inc/hw/dpp.h:1: warning: no structured
comments found
This commit fixes this issue by adding a simple kernel-doc to a struct
in the opp.h and the dpp.h files.
Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building the kernel-doc, it has the following complaints:
Documentation/gpu/amdgpu/display/dcn-blocks:23:
drivers/gpu/drm/amd/display/dc/inc/hw/hubp.h:3: WARNING: Duplicate C
declaration, also defined at gpu/amdgpu/display/dcn-blocks:3.
Declaration is '.. c:struct:: surface_flip_registers'.
Documentation/gpu/amdgpu/display/dcn-blocks:35:
drivers/gpu/drm/amd/display/dc/inc/hw/hubp.h:3: WARNING: Duplicate C
declaration, also defined at gpu/amdgpu/display/dcn-blocks:3.
Declaration is '.. c:struct:: surface_flip_registers'.
This error happened due to a copy-and-paste where the same file path was
duplicated multiple times to a different set of blocks. This commit
addresses this issue by using the correct file path.
Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Documentation/gpu: Remove ':export:' option from DCN documentation
This commit reduces, but does not fix, all the occurrences and some of
the documentation warnings related to the 'no structured comments.' This
was caused by the wrong use of the ':export:' option in the DCN
kernel-doc, so this commit drops the usage of those options.
Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Move DIO documentation to the right place
When building the kernel-doc, it complains with the below warning:
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
This warning was caused by the wrong use of the ':export:' and the lack
of function documentation in the file pointed under the ':internal:'.
This commit addresses those issues by relocating the overview
documentation to the correct C file, removing the ':export:' options,
and adding two simple kernel-doc to ensure that ':internal:' does not
have any warning.
Cc: Alex Deucher <alexander.deucher@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Link: https://lore.kernel.org/dri-devel/20240715085918.68f5ecc9@canb.auug.org.au/ Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Li Ma <li.ma@amd.com> Reviewed-by: Tim Huang <tim.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tim Huang [Fri, 12 Jul 2024 03:05:07 +0000 (11:05 +0800)]
drm/amd/pm: early return if disabling DPMS for GFX IP v11.5.2
This was intended to add support for GFX IP v11.5.2, but it needs
to be applied to all GFX11 and subsequent APUs. Therefore the code
should be revised to accommodate this.
Signed-off-by: Tim Huang <tim.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roman Li [Mon, 15 Jul 2024 20:45:46 +0000 (16:45 -0400)]
drm/amd/display: Add function banner for idle_workqueue
[Why]
htmldocs warning:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h: warning:
Function parameter or struct member 'idle_workqueue' not described in
'amdgpu_display_manager'.
[How]
Add comment section for idle_workqueue with param description.
Imre Deak [Mon, 8 Jul 2024 19:00:25 +0000 (22:00 +0300)]
drm/i915/dp: Don't switch the LTTPR mode on an active link
Switching to transparent mode leads to a loss of link synchronization,
so prevent doing this on an active link. This happened at least on an
Intel N100 system / DELL UD22 dock, the LTTPR residing either on the
host or the dock. To fix the issue, keep the current mode on an active
link, adjusting the LTTPR count accordingly (resetting it to 0 in
transparent mode).
v2: Adjust code comment during link training about reiniting the LTTPRs.
(Ville)
Fixes: 7b2a4ab8b0ef ("drm/i915: Switch to LTTPR transparent mode link training") Reported-and-tested-by: Gareth Yu <gareth.yu@intel.com> Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/10902 Cc: <stable@vger.kernel.org> # v5.15+ Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-3-imre.deak@intel.com
(cherry picked from commit 211ad49cf8ccfdc798a719b4d1e000d0a8a9e588) Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Imre Deak [Mon, 8 Jul 2024 19:00:24 +0000 (22:00 +0300)]
drm/i915/dp: Reset intel_dp->link_trained before retraining the link
Regularly retraining a link during an atomic commit happens with the
given pipe/link already disabled and hence intel_dp->link_trained being
false. Ensure this also for retraining a DP SST link via direct calls to
the link training functions (vs. an actual commit as for DP MST). So far
nothing depended on this, however the next patch will depend on
link_trained==false for changing the LTTPR mode to non-transparent.
Increase the KMS minor version to indicate GFX12 DCC support since this
contains a major change in how DCC is managed across IPs like GFX, DCN
etc. This will be used mainly by userspace like Mesa to figure out
DCC support on GFX12 hardware.
v2: fix version number (Alex)
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Marek Olšák <marek.olsak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/v3d: Fix Indirect Dispatch configuration for V3D 7.1.6 and later
`args->cfg[4]` is configured in Indirect Dispatch using the number of
batches. Currently, for all V3D tech versions, `args->cfg[4]` equals the
number of batches subtracted by 1. But, for V3D 7.1.6 and later, we must not
subtract 1 from the number of batches.
Implement the fix by checking the V3D tech version and revision.
Fixes several `dEQP-VK.synchronization*` CTS tests related to Indirect Dispatch.
Signed-off-by: Leo Li <sunpeng.li@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit dc1000bf463d1d89f66d6b5369cf76603f32c4d3)
Nathan Chancellor [Thu, 20 Jun 2024 15:48:16 +0000 (08:48 -0700)]
drm/omap: Restrict compile testing to PAGE_SIZE less than 64KB
Prior to commit dc6fcaaba5a5 ("drm/omap: Allow build with
COMPILE_TEST=y"), it was only possible to build the omapdrm driver with
a 4KB page size. After that change, when the PAGE_SIZE is 64KB or
larger, clang points out that the driver has some assumptions around the
page size implicitly by passing PAGE_SIZE to a parameter with a type of
u16:
drivers/gpu/drm/omapdrm/omap_gem.c:758:7: error: implicit conversion from 'unsigned long' to 'u16' (aka 'unsigned short') changes value from 65536 to 0 [-Werror,-Wconstant-conversion]
757 | block = tiler_reserve_2d(fmt, omap_obj->width, omap_obj->height,
| ~~~~~~~~~~~~~~~~
758 | PAGE_SIZE);
| ^~~~~~~~~
arch/powerpc/include/asm/page.h:25:34: note: expanded from macro 'PAGE_SIZE'
25 | #define PAGE_SIZE (ASM_CONST(1) << PAGE_SHIFT)
| ~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/gpu/drm/omapdrm/omap_gem.c:1504:44: error: implicit conversion from 'unsigned long' to 'u16' (aka 'unsigned short') changes value from 65536 to 0 [-Werror,-Wconstant-conversion]
1504 | block = tiler_reserve_2d(fmts[i], w, h, PAGE_SIZE);
| ~~~~~~~~~~~~~~~~ ^~~~~~~~~
arch/powerpc/include/asm/page.h:25:34: note: expanded from macro 'PAGE_SIZE'
25 | #define PAGE_SIZE (ASM_CONST(1) << PAGE_SHIFT)
| ~~~~~~~~~~~~~^~~~~~~~~~~~~
2 errors generated.
As there is a lot of use of a u16 type throughout this driver and it
will only ever be run on hardware that has a 4KB page size, just
restrict compile testing to when the page size is less than 64KB (as no
other issues have been discussed and it keeps compile testing relatively
more available).
Dave Airlie [Fri, 12 Jul 2024 00:42:16 +0000 (10:42 +1000)]
Merge tag 'drm-misc-next-fixes-2024-07-11' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
A fix for fbdev on big endian systems, a condition fix for a sharp panel
at removal, and a fix for qxl to prevent unpinned buffer access under
certain conditions.
Matthew Brost [Mon, 8 Jul 2024 21:10:08 +0000 (14:10 -0700)]
drm/xe: Drop trace_xe_hw_fence_free
fence->ctx may be stale memory when trace_xe_hw_fence_free is called
resuling UAF bug when deriving the device name. This tracepoint is not
all that useful, so just drop it.
Fixes: 501c4255c409 ("drm/xe/trace: Print device_id in xe_trace events") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240708211008.956384-1-matthew.brost@intel.com
(cherry picked from commit caaf1f44a6a27bae33eee189842c4d8fc21c3b02) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Ashutosh Dixit [Wed, 3 Jul 2024 16:48:01 +0000 (09:48 -0700)]
drm/xe/uapi: Rename xe perf layer as xe observation layer
In Xe, the perf layer allows capture of HW counter streams. These HW
counters are generally performance related but don't have to be necessarily
so. Also, the name "perf" is a carryover from i915 and is not preferred.
Here we propose the name "observation" for this common layer which allows
capture of different types of these counter streams.
v2: Rename observability layer to observation layer (Lucas/Rodrigo)
v3: Rename sysctl file to "observation_paranoid" (Jose)
Fixes: 52c2e956dceb ("drm/xe/perf/uapi: "Perf" layer to support multiple perf counter stream types") Fixes: fe8929bdf835 ("drm/xe/perf/uapi: Add perf_stream_paranoid sysctl") Acked-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Acked-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240703164801.2561423-1-ashutosh.dixit@intel.com
(cherry picked from commit 8169b2097d88d99d7e4a72e20e4b549efe9eb8d7) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
drm/amdgpu: timely save bad pages to eeprom after gpu ras reset is completed
The problem case is as follows:
1. GPU A triggers a gpu ras reset, and GPU A drives
GPU B to also perform a gpu ras reset.
2. After gpu B ras reset started, gpu B queried a DE
data. Since the DE data was queried in the ras reset
thread instead of the page retirement thread, bad
page retirement work would not be triggered. Then
even if all gpu resets are completed, the bad pages
will be cached in RAM until GPU B's bad page retirement
work is triggered again and then saved to eeprom.
This patch can save the bad pages to eeprom in time after gpu
ras reset is completed.
v2:
1. Add the above description to code comments.
2. Reuse existing function.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / nvme.git / log