A Broadcom AC201 PHY (same entry as 5241) would be flagged by the
Broadcom UniMAC MDIO controller as not completing the turn around
properly since the PHY expects 65 MDC clock cycles to complete a write
cycle, and the MDIO controller was only sending 64 MDC clock cycles as
determined by looking at a scope shot.
This would make the subsequent read fail with the UniMAC MDIO controller
command field having MDIO_READ_FAIL set and we would abort the
brcm_fet_config_init() function and thus not probe the PHY at all.
After issuing a software reset, wait for at least 1ms which is well
above the 1us reset delay advertised by the datasheet and issue a dummy
read to let the PHY turn around the line properly. This read
specifically ignores -EIO which would be returned by MDIO controllers
checking for the line being turned around.
If we have a genuine reaad failure, the next read of the interrupt
status register would pick it up anyway.
If the MAC address A is configured to vport A and then vport B. The MAC
address of vport A in the hardware becomes invalid. If the address of
vport A is changed to MAC address B, the driver needs to delete the MAC
address A of vport A. Due to the MAC address A of vport A has become
invalid in the hardware entry, so "-ENOENT" is returned. In this case, the
"used_umv_size" value recorded in driver is not updated. As a result, the
MAC entry status of the software is inconsistent with that of the hardware.
Therefore, the driver updates the umv size even if the MAC entry cannot be
found. Ensure that the software and hardware status is consistent.
Fixes: ee4bcd3b7ae4 ("net: hns3: refactor the MAC address configure") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
is_xen_pmu() is taking the cpu number as parameter, but it is not using
it. Instead it just tests whether the Xen PMU initialization on the
current cpu did succeed. As this test is done by checking a percpu
pointer, preemption needs to be disabled in order to avoid switching
the cpu while doing the test. While resuming from suspend() this seems
not to be the case:
[ 88.082751] ACPI: PM: Low-level resume complete
[ 88.087933] ACPI: EC: EC started
[ 88.091464] ACPI: PM: Restoring platform NVS memory
[ 88.097166] xen_acpi_processor: Uploading Xen processor PM info
[ 88.103850] Enabling non-boot CPUs ...
[ 88.108128] installing Xen timer for CPU 1
[ 88.112763] BUG: using smp_processor_id() in preemptible [00000000] code: systemd-sleep/7138
[ 88.122256] caller is is_xen_pmu+0x12/0x30
[ 88.126937] CPU: 0 PID: 7138 Comm: systemd-sleep Tainted: G W 5.16.13-2.fc32.qubes.x86_64 #1
[ 88.137939] Hardware name: Star Labs StarBook/StarBook, BIOS 7.97 03/21/2022
[ 88.145930] Call Trace:
[ 88.148757] <TASK>
[ 88.151193] dump_stack_lvl+0x48/0x5e
[ 88.155381] check_preemption_disabled+0xde/0xe0
[ 88.160641] is_xen_pmu+0x12/0x30
[ 88.164441] xen_smp_intr_init_pv+0x75/0x100
Fix that by replacing is_xen_pmu() by a simple boolean variable which
reflects the Xen PMU initialization state on cpu 0.
Modify xen_pmu_init() to return early in case it is being called for a
cpu other than cpu 0 and the boolean variable not being set.
Fixes: bf6dfb154d93 ("xen/PMU: PMU emulation code") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20220325142002.31789-1-jgross@suse.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When registering a clock that doesn't have a recalc_rate implementation,
and doesn't have its parent registered yet, we initialize the clk_core
rate and 'req_rate' fields to 0.
The rate field is later updated when the parent is registered in
clk_core_reparent_orphans_nolock() using __clk_recalc_rates(), but the
'req_rate' field is never updated.
This leads to an issue in clk_set_rate_range() and clk_put(), since
those functions will call clk_set_rate() with the content of 'req_rate'
to provide drivers with the opportunity to change the rate based on the
new boundaries. In this case, we would call clk_set_rate() with a rate
of 0, effectively enforcing the minimum allowed for this clock whenever
we would call one of those two functions, even though the actual rate
might be within range.
Let's fix this by setting 'req_rate' in
clk_core_reparent_orphans_nolock() with the rate field content just
updated by the call to __clk_recalc_rates().
Fixes: aec89f78cf01 ("clk: qcom: Add support for msm8994 global clock controller") Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20220319174940.341137-1-konrad.dybcio@somainline.org Tested-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently kdb_putarea_size() uses copy_from_kernel_nofault() to write *to*
arbitrary kernel memory. This is obviously wrong and means the memory
modify ('mm') command is a serious risk to debugger stability: if we poke
to a bad address we'll double-fault and lose our debug session.
Fix this the (very) obvious way.
Note that there are two Fixes: tags because the API was renamed and this
patch will only trivially backport as far as the rename (and this is
probably enough). Nevertheless Christoph's rename did not introduce this
problem so I wanted to record that!
Fixes: fe557319aa06 ("maccess: rename probe_kernel_{read,write} to copy_{from,to}_kernel_nofault") Fixes: 5d5314d6795f ("kdb: core for kgdb back end (1 of 2)") Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20220128144055.207267-1-daniel.thompson@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not reset IP_CT_TCP_FLAG_BE_LIBERAL flag in out-of-sync scenarios
coming before the TCP window tracking, otherwise such connections will
fail in the window check.
Update tcp_options() to leave this flag in place and add a new helper
function to reset the tcp window state.
Based on patch from Sven Auhagen.
Fixes: c4832c7bbc3f ("netfilter: nf_ct_tcp: improve out-of-sync situation in TCP tracking") Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported divide error in dbNextAG(). The problem was in missing
validation check for malicious image.
Syzbot crafted an image with bmp->db_numag equal to 0. There wasn't any
validation checks, but dbNextAG() blindly use bmp->db_numag in divide
expression
Fix it by validating bmp->db_numag in dbMount() and return an error if
image is malicious
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: syzbot+46f5c25af73eb8330eb6@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When "driver_async_probe=nulltty" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
environment strings, polluting them.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc6
driver_async_probe=nulltty", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
driver_async_probe=nulltty
Change the return value of the __setup function to 1 to indicate
that the __setup option has been handled.
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: 1ea61b68d0f8 ("async: Add cmdline option to specify drivers to be async probed") Cc: Feng Tang <feng.tang@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220301041829.15137-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Google Coreboot implementation requires IOMEM functions
(memmremap, memunmap, devm_memremap), but does not specify this is its
Kconfig. This results in build errors when HAS_IOMEM is not set, such as
on some UML configurations:
/usr/bin/ld: drivers/firmware/google/coreboot_table.o: in function `coreboot_table_probe':
coreboot_table.c:(.text+0x311): undefined reference to `memremap'
/usr/bin/ld: coreboot_table.c:(.text+0x34e): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/memconsole-coreboot.o: in function `memconsole_probe':
memconsole-coreboot.c:(.text+0x12d): undefined reference to `memremap'
/usr/bin/ld: memconsole-coreboot.c:(.text+0x17e): undefined reference to `devm_memremap'
/usr/bin/ld: memconsole-coreboot.c:(.text+0x191): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_section_destroy.isra.0':
vpd.c:(.text+0x300): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_section_init':
vpd.c:(.text+0x382): undefined reference to `memremap'
/usr/bin/ld: vpd.c:(.text+0x459): undefined reference to `memunmap'
/usr/bin/ld: drivers/firmware/google/vpd.o: in function `vpd_probe':
vpd.c:(.text+0x59d): undefined reference to `memremap'
/usr/bin/ld: vpd.c:(.text+0x5d3): undefined reference to `memunmap'
collect2: error: ld returned 1 exit status
Fixes: a28aad66da8b ("firmware: coreboot: Collapse platform drivers into bus core") Acked-By: anton ivanov <anton.ivanov@cambridgegreys.com> Acked-By: Julius Werner <jwerner@chromium.org> Signed-off-by: David Gow <davidgow@google.com> Link: https://lore.kernel.org/r/20220225041502.1901806-1-davidgow@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__setup() handlers should return 1 to indicate that the boot option
has been handled. A return of 0 causes the boot option/value to be
listed as an Unknown kernel parameter and added to init's (limited)
environment strings. So return 1 from kgdbts_option_setup().
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd kgdbts=", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd
kgdbts=
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: e8d31c204e36 ("kgdb: add kgdb internal test suite") Cc: kgdb-bugreport@lists.sourceforge.net Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Douglas Anderson <dianders@chromium.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220308033255.22118-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f165f (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine") Reported-by: Gilles Buloz <gilles.buloz@kontron.com> Tested-by: Gilles Buloz <gilles.buloz@kontron.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
So return 1 from kgdboc_option_setup().
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd kgdbts=", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd
kgdbts=
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Fixes: 1bd54d851f50 ("kgdboc: Passing ekgdboc to command line causes panic") Fixes: f2d937f3bf00 ("consoles: polling support, kgdboc") Cc: He Zhe <zhe.he@windriver.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: kgdb-bugreport@lists.sourceforge.net Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Douglas Anderson <dianders@chromium.org> Cc: linux-serial@vger.kernel.org Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20220309033018.17936-1-rdunlap@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
__setup() handlers should return 1 to indicate that the boot option
has been handled or 0 to indicate that it was not handled.
Add a pr_warn() message if the option value is invalid and then
always return 1.
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 1e747e59cc4d ("pinctrl: rockchip: base regmap supplied by a syscon") Fixes: 14dee8677e19 ("pinctrl: rockchip: let pmu registers be supplied by a syscon") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220307120234.28657-1-linmq006@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
mtk_pconf_group_get(), used to read back pingroup pin config state,
simply returns a set of configs saved from a previous invocation of
mtk_pconf_group_set(). This is an unfiltered, unvalidated set passed
in from the pinconf core, which does not match the current hardware
state.
Since the driver library is designed to have one pin per group, pass
through mtk_pconf_group_get() to mtk_pinconf_get(), to read back the
current pin config state of the only pin in the group.
Also drop the assignment of pin config state to the group.
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220308100956.2750295-5-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For mtk_pinconf_get(), the "argument" argument is typically returned by
pinconf_to_config_argument(), which holds the value for a given pinconf
parameter. It certainly should not have the type of "enum pin_config_param",
which describes the type of the pinconf parameter itself.
Change the type to u32, which matches the return type of
pinconf_to_config_argument().
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220308100956.2750295-4-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When reading back pin bias settings, if the pin is not in the
corresponding bias state, the function should return -EINVAL.
Fix this in the mediatek-paris pinctrl library so that the read back
state is not littered with bogus a "input bias disabled" combined with
"pull up" or "pull down" states.
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220308100956.2750295-3-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the GB-PC2 devicetree. Refer to the schematics of the device for more
information.
GB-PC2 devicetree fixes:
- Include mt7621.dtsi instead of gbpc1.dts. Add the missing definitions.
- Remove gpio-leds node as the system LED is not wired to anywhere on
the board and the power LED is directly wired to GND.
- Remove uart3 pin group from gpio-pinmux node as it's not used as GPIO.
- Use reg 7 for the external phy to be on par with
Documentation/devicetree/bindings/net/dsa/mt7530.txt.
- Use the status value "okay".
Add pinctrl properties with rgmii1 & mdio pins under ethernet node which
was wrongfully put under an external phy node.
GMAC1 will start working with this fix.
Fix LED and pinctrl definitions on the GB-PC1 devicetree. Refer to the
schematics of the device for more information.
LED fixes:
- Change GPIO6 LED label from system to power as GPIO6 is connected to
PLED.
- Add default-on default-trigger to power LED.
- Change GPIO8 LED label from status to system as GPIO8 is connected to
SYS_LED.
- Add disk-activity default-trigger to system LED.
- Switch to the color:function naming scheme.
- Remove lan1 and lan2 LEDs as they don't exist.
Pinctrl fixes:
- Claim state_default node under pinctrl node.
- Change pinctrl0 node name to state-default.
- Change gpio node name to gpio-pinmux to respect
Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinmux.yaml.
- Sort pin groups alphabetically.
Misc fixes:
- Fix formatting.
- Use the status value "okay".
- Define hexadecimal addresses in lower case.
- Make hexadecimal addresses for memory easier to read.
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
In preparation for removing BLK aperture support the NVDIMM unit tests
discovered that the default alignment can be set higher than the
capacity of the region. Fall back to PAGE_SIZE in that case.
Given this has not been seen in the wild, elide notifying -stable.
The device_node pointer is returned by of_parse_phandle() or
of_get_child_by_name() with refcount incremented.
We should use of_node_put() on it when done.
This function only call of_node_put(node) when of_address_to_resource
succeeds, missing error cases.
Remove the loaded hisi_dma driver and reload it, the driver fails
to work properly. The following error is reported in the kernel log:
[ 1475.597609] hisi_dma 0000:7b:00.0: Failed to allocate MSI vectors!
[ 1475.604915] hisi_dma: probe of 0000:7b:00.0 failed with error -28
As noted in "The MSI Driver Guide HOWTO"[1], the number of MSI
interrupt must be a power of two. The Kunpeng DMA driver allocates 30
MSI interrupts. As a result, no space left on device is reported
when the driver is reloaded and allocates interrupt vectors from the
interrupt domain.
This patch changes the number of interrupt vectors allocated by
hisi_dma driver to 32 to avoid this problem.
The display pixel clock has a requirement on certain newer platforms to
support M/N as (2/3) and the final D value calculated results in
underflow errors.
As the current implementation does not check for D value is within
the accepted range for a given M & N value. Update the logic to
calculate the final D value based on the range.
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. The
CCGR121 belongs to ECSPI2 and it is not shared.
Fixes: 8f6d8094b215b57 ("ARM: imx: add imx7d clk tree support") Reported-by: David Wolfe <david.wolfe@nxp.com> Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20220127141052.1900174-2-abel.vesa@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When valid kernel command line parameters
dma_debug=off dma_debug_entries=100
are used, they are reported as Unknown parameters and added to init's
environment strings, polluting it.
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc5
dma_debug=off dma_debug_entries=100", will be passed to user space.
and
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc5
dma_debug=off
dma_debug_entries=100
Return 1 from these __setup handlers to indicate that the command line
option has been handled.
Fixes: 59d3daafa1726 ("dma-debug: add kernel command line parameters") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Joerg Roedel <joro@8bytes.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: iommu@lists.linux-foundation.org Cc: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
The use of mapping_set_error() in conjunction with calls to
filemap_check_errors() is problematic because every error gets reported
as either an EIO or an ENOSPC by filemap_check_errors() in functions
such as filemap_write_and_wait() or filemap_write_and_wait_range().
In almost all cases, we prefer to use the more nuanced wb errors.
Fixes: b8946d7bfb94 ("NFS: Revalidate the file mapping on all fatal writeback errors") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e82303 ("phy: dphy: Add configuration helpers") Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Vinod Koul <vkoul@kernel.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Maxime Ripard <mripard@kernel.org> Cc: Guido Günther <agx@sigxcpu.org> Signed-off-by: Liu Ying <victor.liu@nxp.com> Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use floor ops on SDCC1 APPS clock in order to round down selected clock
frequency and avoid overclocking SD/eMMC cards.
For example, currently HS200 cards were failling tuning as they were
actually being clocked at 384MHz instead of 192MHz.
This caused some boards to disable 1.8V I/O and force the eMMC into the
standard HS mode (50MHz) and that appeared to work despite the eMMC being
overclocked to 96Mhz in that case.
There was a previous commit to use floor ops on SDCC clocks, but it looks
to have only covered SDCC2 clock.
Fixes: 9607f6224b39 ("clk: qcom: ipq8074: add PCIE, USB and SDCC clocks") Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> Signed-off-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220210173100.505128-1-robimarko@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The checker failed to validate all enum IDs in the description of a
register with fixed-width register fields, due to a miscalculation of
the number of described states: each register field of n bits can have
"1 << n" possible states, not "1".
Increase SH_PFC_MAX_ENUMS accordingly, now more enum IDs are checked
(SH-Mobile AG5 has more than 4000 enum IDs defined).
The second video-in channel on RZ/G1C has only 12 data lanes, but the
pin control driver uses the vin_data union, which is meant for 24 data
lanes, thus wasting space.
The bit reversal was wrong for bits 1 and 3 of the 5 bits.
Result is driver failure to probe if you have more than 2 daisy-chained
devices. Discovered via QEMU based device emulation.
Fixes tag is for when this moved from a macro to a function, but it
was broken before that.
The mma8452_driver declares both of_match_table and i2c_driver.id_table
match-tables, but its probe() function only checked for of matches.
Add support for i2c_device_id matches. This fixes the driver not loading
on some x86 tablets (e.g. the Nextbook Ares 8) where the i2c_client is
instantiated by platform code using an i2c_device_id.
Drop of_match_ptr() protection to avoid unused warning.
Fixes: c3cdd6e48e35 ("iio: mma8452: refactor for seperating chip specific data") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220208124336.511884-1-hdegoede@redhat.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix PCI-E clock related kernel oops that are caused by a missing clock
parent.
pcie0_rchng_clk_src has num_parents set to 2 but only one parent is
actually set via parent_hws, it should also have "XO" defined.
This will cause the kernel to panic on a NULL pointer in
clk_core_get_parent_by_index().
So, to fix this utilize clk_parent_data to provide gcc_xo_gpll0 parent
data.
Since there is already an existing static const char * const gcc_xo_gpll0[]
used to provide the same parents via parent_names convert those users to
clk_parent_data as well.
Without this earlycon is needed to even catch the OOPS as it will reset
the board before serial is initialized with the following:
The fuse consists of 64 bits, with this statement we're supposed to get
the upper 32 bits but it actually read out of bounds and got 0 instead
of the desired value which lead to the "PVS bin not set." codepath being
run resetting our pvs value.
Fixes: a8811ec764f9 ("cpufreq: qcom: Add support for krait based socs") Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A struct device can never be devm_alloc()'ed.
Here, it is embedded in "struct fsi_master", and "struct fsi_master" is
embedded in "struct fsi_master_aspeed".
Since "struct device" is embedded, the data structure embedding it must be
released with the release function, as is already done here.
So use kzalloc() instead of devm_kzalloc() when allocating "aspeed" and
update all error handling branches accordingly.
This prevent a potential double free().
This also fix another issue if opb_readl() fails. Instead of a direct
return, it now jumps in the error handling path.
When a driver calls pwmchip_add() it has to be prepared to immediately
get its callbacks called. So move allocation of driver data and hardware
initialization before the call to pwmchip_add().
This fixes a potential NULL pointer exception and a race condition on
register writes.
When LSR is 0xff in ->activate() (rather unlike), we return an error.
Provided ->shutdown() is not called when ->activate() fails, nothing
actually frees the buffer in this case.
Fix this by properly freeing the buffer in a designated label. We jump
there also from the "!info->type" if now too.
In the timer callback function tipc_sk_timeout(), we're trying to
reschedule another timeout to retransmit a setup request if destination
link is congested. But we use the incorrect timeout value
(msecs_to_jiffies(100)) instead of (jiffies + msecs_to_jiffies(100)),
so that the timer expires immediately, it's irrelevant for original
description.
In this commit we correct the timeout value in sk_reset_timer()
Fixes: 6787927475e5 ("tipc: buffer overflow handling in listener socket") Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Link: https://lore.kernel.org/r/20220321042229.314288-1-hoang.h.le@dektech.com.au Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since 5d50aa83e2c8 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
After recent fixes to ICMPv6 PTB handling we started dropping
PMTU updates higher than tp->mss_cache. Because of the stale
tp->mss_cache value PMTU updates during TFO are always dropped.
Thanks to Wei for helping zero in on the problem and the fix!
Fixes: c7bb4b89033b ("ipv6: tcp: drop silly ICMPv6 packet too big messages") Reported-by: Andre Nash <alnash@fb.com> Reported-by: Neil Spring <ntspring@fb.com> Reviewed-by: Wei Wang <weiwan@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220321165957.1769954-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC12 appears to be much smarter about its dependency tracking and is
aware that the relaxed variants are just normal loads and stores and
this is causing problems like:
The assumption when these were relaxed seems to be that device memory
would be mapped non reordering, and that other constructs
(spinlocks/etc) would provide the barriers to assure that packet data
and in memory rings/queues were ordered with respect to device
register reads/writes. This itself seems a bit sketchy, but the real
problem with GCC12 is that it is moving the actual reads/writes around
at will as though they were independent operations when in truth they
are not, but the compiler can't know that. When looking at the
assembly dumps for many of these routines its possible to see very
clean, but not strictly in program order operations occurring as the
compiler would be free to do if these weren't actually register
reads/write operations.
Its possible to suppress the timeout with a liberal bit of dma_mb()'s
sprinkled around but the device still seems unable to reliably
send/receive data. A better plan is to use the safer readl/writel
everywhere.
Since this partially reverts an older commit, which notes the use of
the relaxed variants for performance reasons. I would suggest that
any performance problems with this commit are targeted at relaxing only
the performance critical code paths after assuring proper barriers.
Fixes: 69d2ea9c79898 ("net: bcmgenet: Use correct I/O accessors") Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Acked-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220310045358.224350-1-jeremy.linton@arm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some ATI SB600 USB adapters advertise MSI, but if INTx is disabled by
setting PCI_COMMAND_INTX_DISABLE, MSI doesn't work either. The PCI/PCIe
specs do not require software to set PCI_COMMAND_INTX_DISABLE when enabling
MSI, but Linux has done that for many years.
Mick reported that 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI
devices") broke these devices. Prior to 306c54d0edb6, they used INTx.
Starting with 306c54d0edb6, they use MSI, and and the fact that Linux sets
PCI_COMMAND_INTX_DISABLE means both INTx and MSI are disabled on these
devices.
Avoid this SB600 defect by disabling MSI so we use INTx as before.
When test_lirc_mode2_user exec failed, the test report failed but still
exit with 0. Fix it by exiting with an error code.
Another issue is for the LIRCDEV checking. With bash -n, we need to quote
the variable, or it will always be true. So if test_lirc_mode2_user was
not run, just exit with skip code.
Fixes: 6bdd533cee9a ("bpf: add selftest for lirc_mode2 type program") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220321024149.157861-1-liuhangbin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d44 ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa490 ("i2c: meson: set clock divider in probe instead of setting it for each transfer") Signed-off-by: Lucas Tanure <tanure@linux.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a netlink message is received, netlink_recvmsg() fills in the address
of the sender. One of the fields is the 32-bit bitfield nl_groups, which
carries the multicast group on which the message was received. The least
significant bit corresponds to group 1, and therefore the highest group
that the field can represent is 32. Above that, the UB sanitizer flags the
out-of-bounds shift attempts.
Which bits end up being set in such case is implementation defined, but
it's either going to be a wrong non-zero value, or zero, which is at least
not misleading. Make the latter choice deterministic by always setting to 0
for higher-numbered multicast groups.
To get information about membership in groups >= 32, userspace is expected
to use nl_pktinfo control messages[0], which are enabled by NETLINK_PKTINFO
socket option.
[0] https://lwn.net/Articles/147608/
The way to trigger this issue is e.g. through monitoring the BRVLAN group:
# bridge monitor vlan &
# ip link add name br type bridge
Which produces the following citation:
UBSAN: shift-out-of-bounds in net/netlink/af_netlink.c:162:19
shift exponent 32 is too large for 32-bit type 'int'
The PMTU update and ICMP redirect helper functions initialise their fl4
variable with either __build_flow_key() or build_sk_flow_key(). These
initialisation functions always set ->flowi4_scope with
RT_SCOPE_UNIVERSE and might set the ECN bits of ->flowi4_tos. This is
not a problem when the route lookup is later done via
ip_route_output_key_hash(), which properly clears the ECN bits from
->flowi4_tos and initialises ->flowi4_scope based on the RTO_ONLINK
flag. However, some helpers call fib_lookup() directly, without
sanitising the tos and scope fields, so the route lookup can fail and,
as a result, the ICMP redirect or PMTU update aren't taken into
account.
Fix this by extracting the ->flowi4_tos and ->flowi4_scope sanitisation
code into ip_rt_fix_tos(), then use this function in handlers that call
fib_lookup() directly.
Note 1: We can't sanitise ->flowi4_tos and ->flowi4_scope in a central
place (like __build_flow_key() or flowi4_init_output()), because
ip_route_output_key_hash() expects non-sanitised values. When called
with sanitised values, it can erroneously overwrite RT_SCOPE_LINK with
RT_SCOPE_UNIVERSE in ->flowi4_scope. Therefore we have to be careful to
sanitise the values only for those paths that don't call
ip_route_output_key_hash().
Note 2: The problem is mostly about sanitising ->flowi4_tos. Having
->flowi4_scope initialised with RT_SCOPE_UNIVERSE instead of
RT_SCOPE_LINK probably wasn't really a problem: sockets with the
SOCK_LOCALROUTE flag set (those that'd result in RTO_ONLINK being set)
normally shouldn't receive ICMP redirects or PMTU updates.
That happened because hdev->power_on is already called before
sdio_set_drvdata which btmtksdio_interrupt handler relies on is not
properly set up.
The details are shown as the below: hci_register_dev would run
queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI
workqueue_struct to complete the power-on sequeunce and thus hci_power_on
may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable
the interrupt and thus it is possible that btmtksdio_interrupt is being
called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled
, the kernel oops is going to happen because btmtksdio_interrupt access an
uninitialized pointer.
Fixes: 9aebfd4a2200 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Reviewed-by: Mark Chen <markyawenchen@gmail.com> Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Yake Yang <yake.yang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hci_le_conn_failed function's documentation says that the caller must
hold hdev->lock. The only callsite that does not hold that lock is
hci_le_conn_failed. The other 3 callsites hold the hdev->lock very
locally. The solution is to hold the lock during the call to
hci_le_conn_failed.
The helper macro that records an error in BPF programs that exercise sock
fields access has been inadvertently broken by adaptation work that
happened in commit b18c1f0aa477 ("bpf: selftest: Adapt sock_fields test to
use skel and global variables").
BPF_NOEXIST flag cannot be used to update BPF_MAP_TYPE_ARRAY. The operation
always fails with -EEXIST, which in turn means the error never gets
recorded, and the checks for errors always pass.
Revert the change in update flags.
Fixes: b18c1f0aa477 ("bpf: selftest: Adapt sock_fields test to use skel and global variables") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20220317113920.1068535-2-jakub@cloudflare.com Signed-off-by: Sasha Levin <sashal@kernel.org>
bareudp_create_sock() use AF_INET6 by default if IPv6 CONFIG enabled.
But if user start kernel with ipv6.disable=1, the bareudp sock will
created failed, which cause the interface open failed even with ethertype
ip. e.g.
# ip link add bareudp1 type bareudp dstport 2 ethertype ip
# ip link set bareudp1 up
RTNETLINK answers: Address family not supported by protocol
Fix it by using ipv6_mod_enabled() to check if IPv6 enabled. There is
no need to check IS_ENABLED(CONFIG_IPV6) as ipv6_mod_enabled() will
return false when CONFIG_IPV6 no enabled in include/linux/ipv6.h.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20220315062618.156230-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When providing the MSG_TRUNC flag via recvmsg() syscall the return value
provides the real length of the packet or datagram, even when it was longer
than the passed buffer.
When reading from an unbound can-isotp socket the syscall blocked
indefinitely. As unbound sockets (without given CAN address information)
do not make sense anyway we directly return -EADDRNOTAVAIL on read()
analogue to the known behavior from sendmsg().
The rts51x_read_mem() function should return negative error codes.
Currently if the kmalloc() fails it returns USB_STOR_TRANSPORT_ERROR (3)
which is treated as success by the callers.
Fixes: 065e60964e29 ("ums_realtek: do not use stack memory for DMA") Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220304073504.GA26464@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running xdpsock for a fix duration of time before terminating
using --duration=<n>, there is a race condition that may cause xdpsock
to terminate immediately.
When running for a fixed duration of time the check to determine when to
terminate execution is in is_benchmark_done() and is being executed in
the context of the poller thread,
if (opt_duration > 0) {
unsigned long dt = (get_nsecs() - start_time);
if (dt >= opt_duration)
benchmark_done = true;
}
However start_time is only set after the poller thread have been
created. This leaves a small window when the poller thread is starting
and calls is_benchmark_done() for the first time that start_time is not
yet set. In that case start_time have its initial value of 0 and the
duration check fails as it do not correlate correctly for the
applications start time and immediately sets benchmark_done which in
turn terminates the xdpsock application.
Fix this by setting start_time before creating the poller thread.
Fixes: d3f11b018f6c ("samples/bpf: xdpsock: Add duration option to specify how long to run") Signed-off-by: Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220315102948.466436-1-niklas.soderlund@corigine.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The mem of msg has been uncharged in tcp_bpf_send_verdict() by
sk_msg_return(), and would be uncharged by sk_msg_free() again. When psock
is null, we can simply returning an error code, this would then trigger
the sk_msg_free_nocharge in the error path of __SK_REDIRECT and would have
the side effect of throwing an error up to user space. This would be a
slight change in behavior from user side but would look the same as an
error if the redirect on the socket threw an error.
This issue can cause the following info:
WARNING: CPU: 0 PID: 2136 at net/ipv4/af_inet.c:155 inet_sock_destruct+0x13c/0x260
Call Trace:
<TASK>
__sk_destruct+0x24/0x1f0
sk_psock_destroy+0x19b/0x1c0
process_one_work+0x1b3/0x3c0
worker_thread+0x30/0x350
? process_one_work+0x3c0/0x3c0
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20220304081145.2037182-5-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If tcp_bpf_sendmsg() is running while sk msg is full. When sk_msg_alloc()
returns -ENOMEM error, tcp_bpf_sendmsg() goes to wait_for_memory. If partial
memory has been alloced by sk_msg_alloc(), that is, msg_tx->sg.size is
greater than osize after sk_msg_alloc(), memleak occurs. To fix we use
sk_msg_trim() to release the allocated memory, then goto wait for memory.
Other call paths of sk_msg_alloc() have the similar issue, such as
tls_sw_sendmsg(), so handle sk_msg_trim logic inside sk_msg_alloc(),
as Cong Wang suggested.
This issue can cause the following info:
WARNING: CPU: 3 PID: 7950 at net/core/stream.c:208 sk_stream_kill_queues+0xd4/0x1a0
Call Trace:
<TASK>
inet_csk_destroy_sock+0x55/0x110
__tcp_close+0x279/0x470
tcp_close+0x1f/0x60
inet_release+0x3f/0x80
__sock_release+0x3d/0xb0
sock_close+0x11/0x20
__fput+0x92/0x250
task_work_run+0x6a/0xa0
do_exit+0x33b/0xb60
do_group_exit+0x2f/0xa0
get_signal+0xb6/0x950
arch_do_signal_or_restart+0xac/0x2a0
exit_to_user_mode_prepare+0xa9/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
</TASK>
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Co-developed-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
pgd page is freed by generic implementation pgd_free() since commit f9cb654cb550 ("asm-generic: pgalloc: provide generic pgd_free()"),
however, there are scenarios that the system uses more than one page as
the pgd table, in such cases the generic implementation pgd_free() won't
be applicable anymore. For example, when PAGE_SIZE_4KB is enabled and
MIPS_VA_BITS_48 is not enabled in a 64bit system, the macro "PGD_ORDER"
will be set as "1", which will cause allocating two pages as the pgd
table. Well, at the same time, the generic implementation pgd_free()
just free one pgd page, which will result in the memory leak.
The memory leak can be easily detected by executing shell command:
"while true; do ls > /dev/null; grep MemFree /proc/meminfo; done"
Fixes: f9cb654cb550 ("asm-generic: pgalloc: provide generic pgd_free()") Signed-off-by: Yaliang Wang <Yaliang.Wang@windriver.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) argument or environment
strings. Also, error return codes don't mean anything to
obsolete_checksetup() -- only non-zero (usually 1) or zero.
So return 1 from setup_kmac().
Fixes: 9e21c7e40b7e ("MIPS: RB532: Replace parse_mac_addr() with mac_pton().") Fixes: 73b4390fb234 ("[MIPS] Routerboard 532: Support for base system") Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
From: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Phil Sutter <n0-1@freewrt.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Daniel Walter <dwalter@google.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
This function only calls of_node_put() in the regular path.
And it will cause refcount leak in error path.
Fixes: 727fec790ead ("ath10k: Setup the msa resources before qmi init") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220308070238.19295-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The vxcan driver provides a pair of virtual CAN interfaces to exchange
CAN traffic between different namespaces - analogue to veth.
In opposite to the vcan driver the local sent CAN traffic on this interface
is not echo'ed back but only sent to the remote peer. This is unusual and
can be easily fixed by removing IFF_ECHO from the netdevice flags that
are set for vxcan interfaces by default at startup.
Without IFF_ECHO set on driver level, the local sent CAN frames are echo'ed
in af_can.c in can_send(). This patch makes vxcan interfaces adopt the
same local echo behavior and procedures as known from the vcan interfaces.
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)") Link: https://lore.kernel.org/all/20220309120416.83514-5-socketcan@hartkopp.net Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
mpc8xx_pic_init() should return -ENOMEM instead of 0 when
irq_domain_add_linear() return NULL. This cause mpc8xx_pics_init to continue
executing even if mpc8xx_pic_host is NULL.
In test_lwt_ip_encap, the ingress IPv6 encap test failed from time to
time. The failure occured when an IPv4 ping through the IPv6 GRE
encapsulation did not receive a reply within the timeout. The IPv4 ping
and the IPv6 ping in the test used different timeouts (1 sec for IPv4
and 6 sec for IPv6), probably taking into account that IPv6 might need
longer to successfully complete. However, when IPv4 pings (with the
short timeout) are encapsulated into the IPv6 tunnel, the delays of IPv6
apply.
The actual reason for the long delays with IPv6 was that the IPv6
neighbor discovery sometimes did not complete in time. This was caused
by the outgoing interface only having a tentative link local address,
i.e., not having completed DAD for that lladdr. The ND was successfully
retried after 1 sec but that was too late for the ping timeout.
The IPv6 addresses for the test were already added with nodad. However,
for the lladdrs, DAD was still performed. We now disable DAD in the test
netns completely and just assume that the two lladdrs on each veth pair
do not collide. This removes all the delays for IPv6 traffic in the
test.
Without the delays, we can now also reduce the delay of the IPv6 ping to
1 sec. This makes the whole test complete faster because we don't need
to wait for the excessive timeout for each IPv6 ping that is supposed
to fail.
xsk_umem__create() does mmap for fill/comp rings, but xsk_umem__delete()
doesn't do the unmap. This works fine for regular cases, because
xsk_socket__delete() does unmap for the rings. But for the case that
xsk_socket__create_shared() fails, umem rings are not unmapped.
fill_save/comp_save are checked to determine if rings have already be
unmapped by xsk. If fill_save and comp_save are NULL, it means that the
rings have already been used by xsk. Then they are supposed to be
unmapped by xsk_socket__delete(). Otherwise, xsk_umem__delete() does the
unmap.
Fixes: 2f6324a3937f ("libbpf: Support shared umems between queues and devices") Signed-off-by: Cheng Li <lic121@chinatelecom.cn> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220301132623.GA19995@vscode.7~ Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value of the
mc13xxx_irq_request() and return error if fails.
Fixes: 8e00593557c3 ("mfd: Add mc13892 support to mc13xxx") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20220224022331.3208275-1-jiasheng@iscas.ac.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
Include the DECstation interrupt handler in opting out of
FPU support.
Fixes a linker error:
mips-linux-ld: arch/mips/dec/int-handler.o: in function `fpu':
(.text+0x148): undefined reference to `handle_fpe_int'
Fixes: 183b40f992c8 ("MIPS: Allow FP support to be disabled") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Maciej W. Rozycki <macro@orcam.me.uk> Cc: linux-mips@vger.kernel.org Acked-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.
If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.
This failure mode has not actually been observed, but was found as part
of other driver updates.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log