Erick Archer [Sun, 2 Jun 2024 17:23:54 +0000 (19:23 +0200)]
iio: event: use sizeof(*pointer) instead of sizeof(type)
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). At the same time refactor
the NULL comparison.
Julien Stephan [Thu, 30 May 2024 09:22:46 +0000 (11:22 +0200)]
driver: iio: add missing checks on iio_info's callback access
Some callbacks from iio_info structure are accessed without any check, so
if a driver doesn't implement them trying to access the corresponding
sysfs entries produce a kernel oops such as:
[ 2203.527791] Unable to handle kernel NULL pointer dereference at virtual address 00000000 when execute
[...]
[ 2203.783416] Call trace:
[ 2203.783429] iio_read_channel_info_avail from dev_attr_show+0x18/0x48
[ 2203.789807] dev_attr_show from sysfs_kf_seq_show+0x90/0x120
[ 2203.794181] sysfs_kf_seq_show from seq_read_iter+0xd0/0x4e4
[ 2203.798555] seq_read_iter from vfs_read+0x238/0x2a0
[ 2203.802236] vfs_read from ksys_read+0xa4/0xd4
[ 2203.805385] ksys_read from ret_fast_syscall+0x0/0x54
[ 2203.809135] Exception stack(0xe0badfa8 to 0xe0badff0)
[ 2203.812880] dfa0: 00000003b6f10f8000000003b6eab0000002000000000000
[ 2203.819746] dfc0: 00000003b6f10f807ff000000000000300000003000000000002000000000000
[ 2203.826619] dfe0: b6e1bc88bed80958b6e1bc94b6e1bcb0
[ 2203.830363] Code: bad PC value
[ 2203.832695] ---[ end trace 0000000000000000 ]---
Ramona Gradinariu [Tue, 28 May 2024 14:24:09 +0000 (17:24 +0300)]
docs: iio: add documentation for adis16480 driver
Add documentation for adis16480 driver which describes the driver
device files and shows how the user may use the ABI for various
scenarios (configuration, measurement, etc.).
Ramona Gradinariu [Tue, 28 May 2024 14:24:08 +0000 (17:24 +0300)]
docs: iio: add documentation for interfacing tools
Add documentation for IIO interfacing tools describing the available
tools which can be used to retrieve data from IIO sysfs.
Reference this documentation in adis16475.rst
Ramona Gradinariu [Tue, 28 May 2024 14:24:07 +0000 (17:24 +0300)]
iio: adis16480: add support for adis16545/7 families
The ADIS16545 and ADIS16547 are a complete inertial system that
includes a triaxis gyroscope and a triaxis accelerometer.
The serial peripheral interface (SPI) and register structure provide a
simple interface for data collection and configuration control.
These devices are similar to the ones already supported in the driver,
with changes in the scales, timings and the max spi speed in burst
mode.
Also, they support delta angle and delta velocity readings in burst
mode, for which support was added in the trigger handler.
Ramona Gradinariu [Tue, 28 May 2024 14:24:05 +0000 (17:24 +0300)]
iio: imu: adis16480.c: Add delta angle and delta velocity channels
Add support for delta angle and delta velocity raw readings to
adis16480 driver.
The following devices do not support delta readings in burst mode:
ADIS16375, ADIS16480, ADIS16485, ADIS16488, ADIS16490, ADIS16495-1,
ADIS16495-2, ADIS16495-3, ADIS16497-1, ADIS16497-2, ADIS16497-3, thus
they cannot be retrieved via the buffer interface.
For these devices, the delta measurements are retrieved by performing
normal register readings and are made available through the raw
attributes of the specific channels.
Ramona Gradinariu [Tue, 28 May 2024 14:24:04 +0000 (17:24 +0300)]
iio: adis16480: make the burst_max_speed configurable
With this, we can pass the maxixum spi burst speed to the
'ADIS16480_DATA()' macro. This is in preparation to support new devices
that have a different speed than the one used so far.
Ramona Gradinariu [Mon, 27 May 2024 14:26:17 +0000 (17:26 +0300)]
dt-bindings: iio: imu: Add ADIS1657X family devices compatibles
Add ADIS1657X family devices compatibles and specify the according
maximum SPI baudrate.
Similarly to other ADIS1650X devices, ADIS1657X supports sync-mode
values [0,2].
Each newly added device has a different angular velocity/linear
acceleration/ delta velocity scale combination, as follows:
Accel dynamic range sensitivity:
- 262144000 LSB/g: ADIS16575
- 52428800 LSB/g: ADIS16576, ADIS16577
Gyro dynamic range sensitivity:
- 2621440 LSB/deg/sec: ADIS1575-2, ADIS1576-2, ADIS1577-2
- 655360 LSB/deg/sec: ADIS1575-3, ADIS1576-3, ADIS1577-3
Delta velocity sensitivity:
- 2^15/100 LSB/m/sec: ADIS16575
- 2^15/125 LSB/m/sec: ADIS16576
- 2^15/400 LSB/m/sec: ADIS16577
Each ADIS1657X device supports FIFO usage and a sample-rate of 4.1KHz,
meanwhile the already existing devices do not support FIFO usage and
have a maximum sample-rate of 2.1KHz.
Ramona Gradinariu [Mon, 27 May 2024 14:26:16 +0000 (17:26 +0300)]
iio: imu: adis16475: Re-define ADIS16475_DATA
Re-define ADIS16475_DATA such that it takes _burst_max_len,
_burst_max_speed_hz and _has_fifo as parameters.
Also, do a preparatory rename operation for ADIS16475_BURST32_MAX_DATA
to ADIS16475_BURST32_MAX_DATA_NO_TS32 to be able to differentiate in
the future between devices which are using 16-bit or 32-bit timestamp
size in burst mode.
Ramona Gradinariu [Mon, 27 May 2024 14:26:15 +0000 (17:26 +0300)]
iio: imu: adis_trigger: Allow level interrupts for FIFO readings
Currently, adis library allows configuration only for edge interrupts,
needed for data ready sampling.
This patch removes the restriction for level interrupts for devices
which have FIFO support.
Furthermore, in case of devices which have FIFO support,
devm_request_threaded_irq is used for interrupt allocation, to avoid
flooding the processor with the FIFO watermark level interrupt, which
is active until enough data has been read from the FIFO.
Ramona Gradinariu [Mon, 27 May 2024 14:26:14 +0000 (17:26 +0300)]
drivers: iio: imu: adis16475: generic computation for sample rate
Currently adis16475 supports a sample rate between 1900 and 2100 Hz.
This patch changes the setting of sample rate from hardcoded values to
a generic computation based on the internal clock frequency.
This is a preparatory patch for adding support for adis1657x family
devices which allow sample rates between 3900 and 4100 Hz.
Ramona Gradinariu [Mon, 27 May 2024 14:26:13 +0000 (17:26 +0300)]
iio: imu: adis16475: Create push single sample API
Create push single sample API reposnsible for pushing a single
sample into the buffer.
This is a preparation patch for FIFO support where more than
one sample has to be pushed in the trigger handler.
Ramona Gradinariu [Mon, 27 May 2024 14:26:12 +0000 (17:26 +0300)]
iio: imu: adis_buffer: Add buffer setup API with buffer attributes
Add new API called devm_adis_setup_buffer_and_trigger_with_attrs() which
also takes buffer attributes as a parameter.
Rewrite devm_adis_setup_buffer_and_trigger() implementation such that it
calls devm_adis_setup_buffer_and_trigger_with_attrs() with buffer
attributes parameter NULL
Ramona Gradinariu [Mon, 27 May 2024 14:26:10 +0000 (17:26 +0300)]
dt-bindings: iio: imu: Add ADIS16501 compatibles
Add ADIS16501 compatible. Similarly to other ADIS1650X devices,
ADIS16501 supports sync-mode values [0,2].
There are two differences between ADIS16501 and ADIS16477-2:
- ADIS16501 does not support pulse sync mode
- the delta velocity scale value is different
Julien Stephan [Thu, 30 May 2024 15:14:12 +0000 (10:14 -0500)]
iio: adc: ad7380: add oversampling support
ad7380x(-4) parts are able to do oversampling to increase accuracy.
This chips supports a normal oversampling mode and a rolling mode and
also allows enabling and disabling extra resolution bits when
oversampling is enabled.
We have intentionally left out the rolling mode for now as there is not
a compelling use case for it. User can process a captured data buffer
to get the same effect.
We are also currently not supporting changing the oversampling mode
independently of the resolution bits. The resolution boost feature
can only be enabled when oversampling is enabled and oversampling is
not as useful without the resolution boost. So for now we consider the
features tightly coupled. When oversampling is enabled, the resolution
boost is enabled and when oversampling is disabled, the resolution
boost is disabled.
Since the resolution boost feature causes 16-bit chips to now have
18-bit data which means the storagebits has to change from 16 to 32
bits, we use the new ext_scan_type feature to allow changing the
scan_type at runtime based on if the resolution boost is enabled or
not.
SPI message optimization has to be moved since now some of the xfer
parameters change based on the resolution boost mode.
A few neighboring comments are also fixed up while we are touching this
code.
David Lechner [Thu, 30 May 2024 15:14:11 +0000 (10:14 -0500)]
iio: adc: ad7380: use spi_optimize_message()
This changes the AD7380 to use spi_optimize_message() to optimize
buffered reads.
This changes both direct reads and buffered reads to use the same
spi_message. This has some (welcome) side effects. The first is that
in buffered reads, the timestamp will now correspond to the same sample
rather than the previous sample. The second is that direct reads now
use the same SPI bus speed as buffered reads.
This reduces CPU usage of the IRQ thread from around 25% to around 20%
when sampling at 10 kHz on a ZedBoard.
David Lechner [Thu, 30 May 2024 15:14:10 +0000 (10:14 -0500)]
iio: add support for multiple scan types per channel
This adds new fields to the iio_channel structure to support multiple
scan types per channel. This is useful for devices that support multiple
resolution modes or other modes that require different data formats of
the raw data.
To make use of this, drivers need to implement the new callback
get_current_scan_type() to resolve the scan type for a given channel
based on the current state of the driver. There is a new scan_type_ext
field in the iio_channel structure that should be used to store the
scan types for any channel that has more than one. There is also a new
flag has_ext_scan_type that acts as a type discriminator for the
scan_type/ext_scan_type union. A union is used so that we don't grow
the size of the iio_channel structure and also makes it clear that
scan_type and ext_scan_type are mutually exclusive.
The buffer code is the only code in the IIO core code that is using the
scan_type field. This patch updates the buffer code to use the new
iio_channel_validate_scan_type() function to ensure it is returning the
correct scan type for the current state of the device when reading the
sysfs attributes. The buffer validation code is also update to validate
any additional scan types that are set in the scan_type_ext field. Part
of that code is refactored to a new function to avoid duplication.
Some userspace tools may need to be updated to re-read the scan type
after writing any other attribute. During testing, we noticed that we
had to restart iiod to get it to re-read the scan type after enabling
oversampling on the ad7380 driver.
Julien Stephan [Tue, 28 May 2024 14:20:32 +0000 (16:20 +0200)]
iio: adc: ad7380: prepare for parts with more channels
The current driver supports only parts with 2 channels.
In order to prepare the support of new compatible ADCs with more
channels, this commit:
- defines MAX_NUM_CHANNEL to specify the maximum number of
channels currently supported by the driver
- adds available_scan_mask member in ad7380_chip_info structure
- fixes spi xfer struct len depending on number of channels
- fixes scan_data.raw buffer size to handle more channels
- adds a timing specifications structure in ad7380_chip_info structure
David Lechner [Tue, 28 May 2024 14:20:31 +0000 (16:20 +0200)]
iio: adc: ad7380: add support for pseudo-differential parts
Add support for AD7383, AD7384 pseudo-differential compatible parts.
Pseudo differential parts require common mode voltage supplies so add
the support for them and add the support of IIO_CHAN_INFO_OFFSET to
retrieve the offset
David Lechner [Tue, 28 May 2024 14:20:29 +0000 (16:20 +0200)]
iio: adc: ad7380: new driver for AD7380 ADCs
This adds a new driver for the AD7380 family ADCs.
The driver currently implements basic support for the AD7380, AD7381,
2-channel differential ADCs. Support for additional single-ended,
pseudo-differential and 4-channel chips that use the same register map
as well as additional features of the chip will be added in future patches.
[Julien Stephan: fix rx/tx buffer for regmap access]
[Julien Stephan: fix scale issue]
[Julien Stephan: use the new iio_device_claim_direct_scoped
instead of iio_device_claim_direct_mode]
Co-developed-by: Stefan Popa <stefan.popa@analog.com> Signed-off-by: Stefan Popa <stefan.popa@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: David Lechner <dlechner@baylibre.com>
[Julien Stephan: add datasheet links of supported parts] Signed-off-by: Julien Stephan <jstephan@baylibre.com> Link: https://lore.kernel.org/r/20240528-adding-new-ad738x-driver-v7-2-4cd70a4c12c8@baylibre.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nuno Sa [Fri, 31 May 2024 09:41:55 +0000 (11:41 +0200)]
iio: adc: adi-axi-adc: make sure DRP is locked on enable
When enabling the core, make sure DRP (Dynamic Reconfiguration Port)
is locked. Most of the designs don't really use it but we still get the
lock bit set. So let's do it all the time so the code is generic.
While at it reduce the timeout time to 1 microsecond as it seems to be
enough and goes in line with what we have on the similar DAC core
(adi-axi-dac).
Denis Benato [Thu, 23 May 2024 17:47:36 +0000 (19:47 +0200)]
iio: imu: bmi323: Use iio read_acpi_mount_matrix() helper
bmi150-accel and bmi323-imu are declared in an almost identical way in the ACPI and in some devices such as the Asus RC71L the "ROTM" property can be found: parse and use the ACPI-defined mount-matrix.
Co-developed-by: Luke D. Jones <luke@ljones.dev> Co-developed-by: Jonathan LoBue <jlobue10@gmail.com> Signed-off-by: Denis Benato <benato.denis96@gmail.com> Link: https://lore.kernel.org/r/20240523174736.16692-2-benato.denis96@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
David Lechner [Thu, 23 May 2024 19:24:10 +0000 (14:24 -0500)]
iio: adc: sort Makefile
The Makefile for IIO ADC drivers is intended to be sorted alphabetically.
I can be tricky to keep it sorted when adding new drivers when not all
of the existing drivers are sorted. So let's sort everything now to make
it easier to keep it sorted in the future.
Angelo Dureghello [Wed, 22 May 2024 15:01:40 +0000 (17:01 +0200)]
iio: dac: ad3552r: change AD3552R_NUM_CH define name
After model data and num_hw_channles introduction, we have:
ad3552r_desc, num_ch: used to keep channel number set in fdt,
ad35xxr_model_data, num_hw_channels: for max channel checks,
AD3552R_NUM_CH: just actually used to define the max array size
on allocated arrays.
Renaming AD3552R_NUM_CH to a more consistent name, as AD3552R_MAX_CH.
Angelo Dureghello [Wed, 22 May 2024 15:01:38 +0000 (17:01 +0200)]
iio: dac: ad3552r: add model data structure
Add a "model data" structure to keep useful hardware-related
information as from datasheet, avoiding id-based conditional
choices later on.
Removed id-based checks and filled model-specific structures
with device specific features, In particular, num_hw_channels
is introduced to keep the number of hardware implemented
channels, since 1-channel versions of the DACs are added
in this same patchset.
Angelo Dureghello [Wed, 22 May 2024 15:01:36 +0000 (17:01 +0200)]
dt-bindings: iio: dac: fix ad3552r gain parameter names
The adi,gain-scaling-p/n values are an inverted log2,
so initial naming was set correctly, but the driver uses just
adi,gain-scaling-p/n, and if fdt is created accordingly with
the fdt bindings documentation, driver fails the probe.
Observing that:
- the Linux driver is the only consumer,
- there are no upstreamed dts nodes related to ad3552r,
the fix to the documentation side is preferred and less-risk.
Fixes: b0a96c5f599e ("dt-bindings: iio: dac: Add adi,ad3552r.yaml") Signed-off-by: Angelo Dureghello <adureghello@baylibre.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20240522150141.1776196-2-adureghello@baylibre.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nuno Sa [Wed, 22 May 2024 12:54:06 +0000 (14:54 +0200)]
iio: adc: ad9467: change struct members padding
Using tabs and maintaining the start of the variables aligned is a pain and
may lead to lot's of unrelated changes when adding new members. Hence,
let's change things now and just have a simple space.
Nuno Sa [Wed, 22 May 2024 12:54:05 +0000 (14:54 +0200)]
iio: adc: ad9467: use DMA safe buffer for spi
Make sure we use a DMA safe buffer (IIO_DMA_MINALIGN) for all the spi
transfers. Only relevant for writes since for reads
spi_write_then_read() is used which does not require DMA safe buffers.
Also note that for consistency, ad9467_spi_read() is also taking struct
ad9467_state as a parameter (even if not really needed).
Barnabás Czémán [Tue, 21 May 2024 15:34:51 +0000 (17:34 +0200)]
iio: light: stk3310: relax failure to match id
Relax failure to match ID to a warning rather than probe fail.
This add abilty to use other compatible variants when chip id
is not defined in the driver.
Devices that have both single-ended channels and differential channels
cause a bit of confusion when the channels are configured in the
devicetree.
Clarify difference between these two types of channels for such devices
by adding single-channel property alongside diff-channels. They should
be mutually exclusive.
Devices that have only single-ended channels can still use reg property
to reference a channel like before.
Suggested-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20240514120222.56488-5-alisa.roman@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alisa-Dariana Roman [Tue, 14 May 2024 12:02:19 +0000 (15:02 +0300)]
iio: adc: ad7192: Add aincom supply
AINCOM should actually be a supply. AINx inputs are referenced to AINCOM
in pseudo-differential operation mode. AINCOM voltage represents the
offset of corresponding channels.
Alisa-Dariana Roman [Tue, 14 May 2024 12:02:18 +0000 (15:02 +0300)]
dt-bindings: iio: adc: ad7192: Add aincom supply
AINCOM should actually be a supply. AINx inputs are referenced to AINCOM
in pseudo-differential operation mode. AINCOM voltage represents the
offset of corresponding channels.
For BMP18x, BMP28x, BME280, BMP38x the reading of the pressure
value requires an update of the t_fine variable which happens
through reading the temperature value.
So all the bmpxxx_read_press() functions of the above sensors
are internally calling the equivalent bmpxxx_read_temp() function
in order to update the t_fine value. By just looking at the code
this functionality is a bit hidden and is not easy to understand
why those channels are not independent.
This commit tries to clear these things a bit by splitting the
bmpxxx_{read/compensate}_{temp/press/humid}() to the following:
i. bmpxxx_read_{temp/press/humid}_adc(): read the raw value from
the sensor.
ii. bmpxx_calc_t_fine(): calculate the t_fine variable.
iii. bmpxxx_get_t_fine(): get the t_fine variable.
iv. bmpxxx_compensate_{temp/press/humid}(): compensate the adc
values and return the calculated value.
v. bmpxxx_read_{temp/press/humid}(): combine calls of the
aforementioned functions to return the requested value.
Vasileios Amoiridis [Wed, 8 May 2024 16:52:02 +0000 (18:52 +0200)]
iio: pressure: bmp280: Use unsigned data types for raw sensor data
The raw sensor data that have not been compensated yet cannot be
signed values, so use unsigned ones. Also, compensated pressure
values cannot be negative so use unsigned also there.
Also, drop redundant cast of data->t_fine variable from s32 to s32.
Vasileios Amoiridis [Wed, 8 May 2024 16:52:01 +0000 (18:52 +0200)]
iio: pressure: bmp280: Make error checks consistent
The form 'if (ret)' is used in this driver in order to check
for returned error values. There are also some places that
'if (ret < 0)' is used but for no specific reason. Change
them to 'if (ret)' to make the driver more consistent.
Uwe Kleine-König [Wed, 8 May 2024 07:29:27 +0000 (09:29 +0200)]
iio: Drop explicit initialization of struct i2c_device_id::driver_data to 0
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
iio: pressure: bmp280: Add more intuitive name for bmp180_measure()
The bmp180_measure() function essentially waits for the end of the
current conversion in order to read the values from the sensors. The
name bmp180_measure() could be misinterpreted because it could be
translated as "measure sensor values" even though it was probably
trying to say "measure time for eoc". Give a more intuitive name
to this function to be less confusing.
iio: pressure: bmp280: Use BME prefix for BME280 specifics
Change the rest of the defines and function names that are
used specifically by the BME280 humidity sensor to BME280
as it is done for the rest of the BMP{0,1,3,5}80 sensors.
Matti Vaittinen [Tue, 30 Apr 2024 12:45:21 +0000 (15:45 +0300)]
iio: test: gts: test available times and gains sorting
The iio_gts helpers build available times and scales tables based on the
times and gains arrays given from the driver. The driver should be able
to list all valid register values so that conversion from register valu
to correct gain/time works for all supported register values.
It might be more convenient for drivers to list these times and gains in
the order where they're listed in the data-sheet than ascending order.
However, for user who requests the supported scales / times it is more
convenient to get the results in asscending order. Also, listing
duplicated values is not meaning for the user.
Hence the GTS heler should do sorting and deduplication of the scales
and times when it builds the tables listing the available times/scales.
Note, currently duplicated gain values aren't handled by GTS-helpers.
Unsort the gain and time arrays in the test code, and add duplicates to
time array in order to test the sorting and deduplicating works.
Chenyuan Yang [Tue, 30 Apr 2024 12:44:53 +0000 (15:44 +0300)]
iio: Fix the sorting functionality in iio_gts_build_avail_time_table
The sorting in iio_gts_build_avail_time_table is not working as intended.
It could result in an out-of-bounds access when the time is zero.
Here are more details:
1. When the gts->itime_table[i].time_us is zero, e.g., the time
sequence is `3, 0, 1`, the inner for-loop will not terminate and do
out-of-bound writes. This is because once `times[j] > new`, the value
`new` will be added in the current position and the `times[j]` will be
moved to `j+1` position, which makes the if-condition always hold.
Meanwhile, idx will be added one, making the loop keep running without
termination and out-of-bound write.
2. If none of the gts->itime_table[i].time_us is zero, the elements
will just be copied without being sorted as described in the comment
"Sort times from all tables to one and remove duplicates".
For more details, please refer to
https://lore.kernel.org/all/6dd0d822-046c-4dd2-9532-79d7ab96ec05@gmail.com.
Reported-by: Chenyuan Yang <chenyuan0y@gmail.com> Suggested-by: Matti Vaittinen <mazziesaccount@gmail.com> Fixes: 38416c28e168 ("iio: light: Add gain-time-scale helpers") Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com> Co-developed-by: Matti Vaittinen <mazziesaccount@gmail.com> Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://lore.kernel.org/r/d501ade8c1f7b202d34c6404eda423489cab1df5.1714480171.git.mazziesaccount@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Danila Tikhonov [Sun, 5 May 2024 05:36:54 +0000 (07:36 +0200)]
iio: imu: bmi160: add support for bmi120
Add support for bmi120 low power variant of bmi160.
Relax failure to match ID to a warning rather than probe fail.
This allows for fallback compatibles, whilst retaining a useful
debugging message if they turn out not to be so compatible due to
badly behaved firmware.
Kent Overstreet [Fri, 24 May 2024 15:42:09 +0000 (11:42 -0400)]
mm: percpu: Include smp.h in alloc_tag.h
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Linus Torvalds [Sun, 26 May 2024 16:54:26 +0000 (09:54 -0700)]
Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com> Cc: Ethan Adams <j.ethan.adams@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Tycho Andersen <tycho@tycho.pizza> Cc: Yang Jihong <yangjihong@bytedance.com> Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Sun, 26 May 2024 05:33:10 +0000 (22:33 -0700)]
Merge tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
Linus Torvalds [Sat, 25 May 2024 22:10:33 +0000 (15:10 -0700)]
Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
Linus Torvalds [Sat, 25 May 2024 21:48:40 +0000 (14:48 -0700)]
Merge tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
Linus Torvalds [Sat, 25 May 2024 21:40:09 +0000 (14:40 -0700)]
Merge tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
crypto: x86/aes-xts - switch to new Intel CPU model defines
x86/topology: Handle bogus ACPI tables correctly
x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
Linus Torvalds [Sat, 25 May 2024 21:23:58 +0000 (14:23 -0700)]
Merge tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A series from Xiubo that adds support for additional access checks
based on MDS auth caps which were recently made available to clients.
This is needed to prevent scenarios where the MDS quietly discards
updates that a UID-restricted client previously (wrongfully) acked to
the user.
Other than that, just a documentation fixup"
* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
doc: ceph: update userspace command to get CephFS metadata
ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
ceph: check the cephx mds auth access for async dirop
ceph: check the cephx mds auth access for open
ceph: check the cephx mds auth access for setattr
ceph: add ceph_mds_check_access() helper
ceph: save cap_auths in MDS client when session is opened
Linus Torvalds [Sat, 25 May 2024 21:19:01 +0000 (14:19 -0700)]
Merge tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"Fixes:
- reusing of the file index (could cause the file to be trimmed)
- infinite dir enumeration
- taking DOS names into account during link counting
- le32_to_cpu conversion, 32 bit overflow, NULL check
- some code was refactored
Changes:
- removed max link count info display during driver init
Remove:
- atomic_open has been removed for lack of use"
* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Break dir enumeration if directory contents error
fs/ntfs3: Fix case when index is reused during tree transformation
fs/ntfs3: Mark volume as dirty if xattr is broken
fs/ntfs3: Always make file nonresident on fallocate call
fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
fs/ntfs3: Use variable length array instead of fixed size
fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
fs/ntfs3: Check 'folio' pointer for NULL
fs/ntfs3: Missed le32_to_cpu conversion
fs/ntfs3: Remove max link count info display during driver init
fs/ntfs3: Taking DOS names into account during link counting
fs/ntfs3: remove atomic_open
fs/ntfs3: use kcalloc() instead of kzalloc()
Linus Torvalds [Sat, 25 May 2024 21:15:39 +0000 (14:15 -0700)]
Merge tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Two ksmbd server fixes, both for stable"
* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: ignore trailing slashes in share paths
ksmbd: avoid to send duplicate oplock break notifications
Linus Torvalds [Sat, 25 May 2024 20:33:53 +0000 (13:33 -0700)]
Merge tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is one new driver and then most of the changes are the device
tree bindings conversions to yaml.
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support"
* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
pcf8563: add wakeup-source support
rtc: rx8111: handle VLOW flag
rtc: rx8111: demote warnings to debug level
rtc: rx6110: Constify struct regmap_config
dt-bindings: rtc: convert trivial devices into dtschema
dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
dt-bindings: rtc: pxa-rtc: convert to dtschema
rtc: Add driver for Epson RX8111
dt-bindings: rtc: Add Epson RX8111
rtc: mcp795: drop unneeded MODULE_ALIAS
rtc: nuvoton: Modify part number value
rtc: test: Split rtc unit test into slow and normal speed test
dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
dt-bindings: rtc: armada-380-rtc: convert to dtschema
rtc: cros-ec: provide ID table for avoiding fallback match
Linus Torvalds [Sat, 25 May 2024 20:28:29 +0000 (13:28 -0700)]
Merge tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Runtime PM (power management) is improved and hot-join support has
been added to the dw controller driver.
Core:
- Allow device driver to trigger controller runtime PM
Drivers:
- dw: hot-join support
- svc: better IBI handling"
* tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: dw: Add hot-join support.
i3c: master: Enable runtime PM for master controller
i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
i3c: master: svc: change ENXIO to EAGAIN when IBI occurs during start frame
i3c: Add comment for -EAGAIN in i3c_device_do_priv_xfers()
Linus Torvalds [Sat, 25 May 2024 20:23:42 +0000 (13:23 -0700)]
Merge tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull jffs2 updates from Richard Weinberger:
- Fix illegal memory access in jffs2_free_inode()
- Kernel-doc fixes
- print symbolic error names
* tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: Fix potential illegal address access in jffs2_free_inode
jffs2: Simplify the allocation of slab caches
jffs2: nodemgmt: fix kernel-doc comments
jffs2: print symbolic error name instead of error code
Linus Torvalds [Sat, 25 May 2024 20:17:48 +0000 (13:17 -0700)]
Merge tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML updates from Richard Weinberger:
- Fixes for -Wmissing-prototypes warnings and further cleanup
- Remove callback returning void from rtc and virtio drivers
- Fix bash location
* tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: (26 commits)
um: virtio_uml: Convert to platform remove callback returning void
um: rtc: Convert to platform remove callback returning void
um: Remove unused do_get_thread_area function
um: Fix -Wmissing-prototypes warnings for __vdso_*
um: Add an internal header shared among the user code
um: Fix the declaration of kasan_map_memory
um: Fix the -Wmissing-prototypes warning for get_thread_reg
um: Fix the -Wmissing-prototypes warning for __switch_mm
um: Fix -Wmissing-prototypes warnings for (rt_)sigreturn
um: Stop tracking host PID in cpu_tasks
um: process: remove unused 'n' variable
um: vector: remove unused len variable/calculation
um: vector: fix bpfflash parameter evaluation
um: slirp: remove set but unused variable 'pid'
um: signal: move pid variable where needed
um: Makefile: use bash from the environment
um: Add winch to winch_handlers before registering winch IRQ
um: Fix -Wmissing-prototypes warnings for __warp_* and foo
um: Fix -Wmissing-prototypes warnings for text_poke*
um: Move declarations to proper headers
...
Linus Torvalds [Sat, 25 May 2024 00:28:02 +0000 (17:28 -0700)]
Merge tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
David Howells [Fri, 24 May 2024 14:23:36 +0000 (15:23 +0100)]
cifs: Fix missing set of remote_i_size
Occasionally, the generic/001 xfstest will fail indicating corruption in
one of the copy chains when run on cifs against a server that supports
FSCTL_DUPLICATE_EXTENTS_TO_FILE (eg. Samba with a share on btrfs). The
problem is that the remote_i_size value isn't updated by cifs_setsize()
when called by smb2_duplicate_extents(), but i_size *is*.
This may cause cifs_remap_file_range() to then skip the bit after calling
->duplicate_extents() that sets sizes.
Fix this by calling netfs_resize_file() in smb2_duplicate_extents() before
calling cifs_setsize() to set i_size.
This means we don't then need to call netfs_resize_file() upon return from
->duplicate_extents(), but we also fix the test to compare against the pre-dup
inode size.
[Note that this goes back before the addition of remote_i_size with the
netfs_inode struct. It should probably have been setting cifsi->server_eof
previously.]
Fixes: cfc63fc8126a ("smb3: fix cached file size problems in duplicate extents (reflink)") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev Signed-off-by: Steve French <stfrench@microsoft.com>
David Howells [Wed, 22 May 2024 08:38:48 +0000 (09:38 +0100)]
cifs: Fix smb3_insert_range() to move the zero_point
Fix smb3_insert_range() to move the zero_point over to the new EOF.
Without this, generic/147 fails as reads of data beyond the old EOF point
return zeroes.
Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev Signed-off-by: Steve French <stfrench@microsoft.com>
projects / users / jedix / linux-maple.git / log