- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a single IRQ
line and cannot set the affinity of each MSI to a specific CPU core
(Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl, xilinx-xdma, and
xilinx drivers to avoid "IRQ: set affinity failed" warnings (Marek Vasut)
- Initialize leds class earlier (with an unfortunate Makefile ordering
change) so the PCI NPEM driver can use it (Mariusz Tkaczyk)
- Add Native PCIe Enclosure Management (NPEM) support for sysfs control of
NVMe RAID storage indicators (ok/fail/locate/rebuild/etc) (Mariusz
Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which is
functionally similar to NPEM but mediated by platform firmware (Mariusz
Tkaczyk)
* pci/npem:
PCI/NPEM: Add _DSM PCIe SSD status LED management
PCI/NPEM: Add Native PCIe Enclosure Management support
leds: Init leds class earlier
- Clear LBMS bit after a manual link retrain so we don't try to retrain a
link when there's no downstream device anymore (Maciej W. Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance to use
higher speeds (Maciej W. Rozycki)
- Correct interpretation of pcie_retrain_link() return status and update it
to return 0/errno instead of true/false (Maciej W. Rozycki)
* pci/enumeration:
PCI: Use an error code with PCIe failed link retraining
PCI: Correct error reporting with PCIe failed link retraining
PCI: Revert to the original speed after PCIe failed link retraining
PCI: Clear the LBMS bit after a link retrain
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions() (Philipp
Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp Stanner)
* pci/devres:
drm/ast: Request PCI BAR with devres
PCI: Deprecate pcim_iomap_regions() in favor of pcim_iomap_region()
drm/vboxvideo: Add PCI region request
PCI: Make pcim_request_region() a public function
- Wait for device readiness after reset by polling Vendor ID and looking
for Configuration RRS instead of polling the Command register and looking
for non-error completions (Bjorn Helgaas)
- Fix an aardvark issue with emulating Configuration RRS for two-byte reads
of Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
- Rename CRS Completion Status to RRS to match spec usage (Bjorn Helgaas)
* pci/crs:
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
Johan Hovold [Tue, 23 Jul 2024 15:13:28 +0000 (17:13 +0200)]
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
Commit 756485bfbb85 ("dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to
dedicated schema") incorrectly removed 'vddpe-3v3-supply' from the
bindings, which results in DT checker warnings like:
arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dtb: pcie@600000: Unevaluated properties are not allowed ('vddpe-3v3-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/pci/qcom,pcie.yaml#
Note that this property has been part of the Qualcomm PCIe bindings since
2018 and would need to be deprecated rather than simply removed if there is
a desire to replace it with 'vpcie3v3' which is used for some non-Qualcomm
controllers.
Siddharth Vadapalli [Tue, 27 Aug 2024 12:24:22 +0000 (17:54 +0530)]
PCI: dra7xx: Fix error handling when IRQ request fails in probe
Commit d4c7d1a089d6 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089d6 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe") Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com Tested-by: Udit Kumar <u-kumar1@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: stable@vger.kernel.org
Siddharth Vadapalli [Tue, 27 Aug 2024 12:24:21 +0000 (17:54 +0530)]
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
Commit da87d35a6e51 ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e51 ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ") Suggested-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com Reported-by: Udit Kumar <u-kumar1@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: stable@vger.kernel.org
Richard Zhu [Tue, 13 Aug 2024 07:42:20 +0000 (15:42 +0800)]
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
Add reg-name: "dbi2", "atu" for i.MX8M PCIe Endpoint.
For i.MX8M PCIe EP, the dbi2 and atu addresses are pre-defined in the
driver. This method is not good.
In commit b7d67c6130ee ("PCI: imx6: Add iMX95 Endpoint (EP) support"),
Frank suggests to fetch the dbi2 and atu from DT directly. This commit is
preparation to do that for i.MX8M PCIe EP.
These changes wouldn't break driver function. When "dbi2" and "atu"
properties are present, i.MX PCIe driver would fetch the according base
addresses from DT directly. If only two reg properties are provided, i.MX
PCIe driver would fall back to the old method.
Richard Zhu [Mon, 29 Jul 2024 20:18:18 +0000 (16:18 -0400)]
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
Implement i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe Root Complex
(RC) support. While the controller resembles that of i.MX8MP, the PHY
differs significantly. Also, there's a distinction between PCI bus
addresses and CPU addresses.
Introduce IMX_PCIE_FLAG_CPU_ADDR_FIXUP in drvdata::flags to indicate driver
need the cpu_addr_fixup() callback to facilitate CPU address to PCI bus
address conversion according to "ranges" property.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-11-b68ee5ef2b4d@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: check resource_list_first_type() for NULL] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Bjorn Helgaas [Tue, 27 Aug 2024 23:48:48 +0000 (18:48 -0500)]
PCI: Rename CRS Completion Status to RRS
PCIe r6.0 changed the abbreviation for "Configuration Request Retry Status"
Completion Status from "CRS" to "RRS" and uses the terminology of
"Configuration RRS Software Visibility" instead of "CRS Software
Visibility".
Align the Linux usage with the r6.0 spec language. No functional change
intended.
It's confusing to make this change, but I think "RRS" *is* a better
abbreviation because it was easy to interpret "CRS" as "Completion Retry
Status", which really didn't make any sense.
Bjorn Helgaas [Tue, 27 Aug 2024 23:48:47 +0000 (18:48 -0500)]
PCI: aardvark: Correct Configuration RRS checking
Per PCIe r6.0, sec 2.3.2, when a Root Complex handles a Completion with
Request Retry Status for a Configuration Read Request that includes both
bytes of the Vendor ID field, it must complete the Request to the host by
returning 0001h for the Vendor ID and all 1's for any additional bytes.
Previously we only returned the 0001h Vendor ID value if we got an RRS
completion for reads of exactly 4 bytes. A read of 2 bytes would not
qualify, although the spec says it should.
Check for reads of 2 or more bytes including the Vendor ID.
I don't think this will fix any observable problems because RRS only
applies to the first config reads after reset, and those are all currently
dword (4-byte) reads.
Bjorn Helgaas [Tue, 27 Aug 2024 23:48:46 +0000 (18:48 -0500)]
PCI: Wait for device readiness with Configuration RRS
After a device reset, delays are required before the device can
successfully complete config accesses. PCIe r6.0, sec 6.6, specifies some
delays required before software can perform config accesses. Devices that
require more time after those delays may respond to config accesses with
Configuration Request Retry Status (RRS) completions.
Callers of pci_dev_wait() are responsible for delays until the device can
respond to config accesses. pci_dev_wait() waits any additional time until
the device can successfully complete config accesses.
Reading config space of devices that are not present or not ready typically
returns ~0 (PCI_ERROR_RESPONSE). Previously we polled the Command register
until we got a value other than ~0. This is sometimes a problem because
Root Complex handling of RRS completions may include several retries and
implementation-specific behavior that is invisible to software (see sec
2.3.2), so the exponential backoff in pci_dev_wait() may not work as
intended.
Linux enables Configuration RRS Software Visibility on all Root Ports that
support it. If it is enabled, read the Vendor ID instead of the Command
register. RRS completions cause immediate return of the 0x0001 reserved
Vendor ID value, so the pci_dev_wait() backoff works correctly.
When a read of Vendor ID eventually completes successfully by returning a
non-0x0001 value (the Vendor ID or 0xffff for VFs), the device should be
initialized and ready to respond to config requests.
For conventional PCI devices or devices below Root Ports that don't support
Configuration RRS Software Visibility, poll the Command register as before.
This was developed independently, but is very similar to Stanislav
Spassov's previous work at
https://lore.kernel.org/linux-pci/20200223122057.6504-1-stanspas@amazon.com
Rename pcie_offsets_bmips_7425[] to pcie_offsets_bcm7425[] to match BCM7425
pcie_soc_base enum, bcm7425_cfg, and "brcm,bcm7425-pcie" .compatible
string.
Rename pcie_offset_bcm7278[] to pcie_offsets_bcm7278[] to match other
"pcie_offsets" names.
Rename pcie_offset_bcm7712[] to pcie_offsets_bcm7712[] to match other
"pcie_offsets" names.
Sort pcie_offsets_*[] by SoC name, move them all together, indent values
for easy reading.
Frank Li [Mon, 29 Jul 2024 20:18:17 +0000 (16:18 -0400)]
PCI: imx6: Call common PHY API to set mode, speed, and submode
Invoke the common PHY API to configure mode, speed, and submode. While
these functions are optional in the PHY interface, they are necessary for
certain PHY drivers. Lack of support for these functions in a PHY driver
does not cause harm.
Frank Li [Mon, 29 Jul 2024 20:18:13 +0000 (16:18 -0400)]
PCI: imx6: Simplify switch-case logic by involve core_reset callback
Instead of using the switch case statement to assert/dassert the core
reset handled by this driver itself, let's introduce a new callback
core_reset() and define it for platforms that require it.
Frank Li [Mon, 29 Jul 2024 20:18:12 +0000 (16:18 -0400)]
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
Instead of using the switch case statement to enable/disable the
reference clock handled by this driver itself, let's introduce a new
callback enable_ref_clk() and define it for platforms that require it.
Frank Li [Mon, 29 Jul 2024 20:18:10 +0000 (16:18 -0400)]
PCI: imx6: Fix missing call to phy_power_off() in error handling
Fix missing call to phy_power_off() in the error path of
imx6_pcie_host_init(). Remove unnecessary check for imx6_pcie->phy
as the PHY API already handles NULL pointers.
Fixes: cbcf8722b523 ("phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()") Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: <stable@vger.kernel.org> # 6.1+
Correct occasional MSI triggering failures in i.MX8MP PCIe EP by applying
the correct hardware outbound alignment requirement.
The i.MX platform has a restriction about outbound address translation. The
pci-epc-mem uses page_size to manage it. Set the correct page_size for i.MX
platform to meet the hardware requirement, which is the same as inbound
address alignment.
Thus, align it with epc_features::align.
Fixes: 1bd0d43dcf3b ("PCI: imx6: Clean up addr_space retrieval code") Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-2-b68ee5ef2b4d@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Jason Liu <jason.hui.liu@nxp.com> Cc: <stable@vger.kernel.org> # 6.9+
Richard Zhu [Mon, 29 Jul 2024 20:18:08 +0000 (16:18 -0400)]
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
Add IMX6_PCIE_FLAG_HAS_APP_RESET flag to IMX8MM_EP and IMX8MP_EP drvdata.
This flag was overlooked during code restructuring. It is crucial to
release the app-reset from the System Reset Controller before initiating
LTSSM to rectify the issue.
Fixes: 0c9651c21f2a ("PCI: imx6: Simplify reset handling by using *_FLAG_HAS_*_RESET") Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-1-b68ee5ef2b4d@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: <stable@vger.kernel.org> # 6.9+
Maciej W. Rozycki [Fri, 9 Aug 2024 13:25:02 +0000 (14:25 +0100)]
PCI: Use an error code with PCIe failed link retraining
Given how the call place in pcie_wait_for_link_delay() got structured now,
and that pcie_retrain_link() returns a potentially useful error code,
convert pcie_failed_link_retrain() to return an error code rather than a
boolean status, fixing handling at the call site mentioned. Update the
other call site accordingly.
Maciej W. Rozycki [Fri, 9 Aug 2024 13:24:56 +0000 (14:24 +0100)]
PCI: Correct error reporting with PCIe failed link retraining
Only return successful completion status from pcie_failed_link_retrain() if
retraining has actually been done, preventing excessive delays from being
triggered at call sites in a hope that communication will finally be
established with the downstream device where in fact nothing has been done
about the link in question that would justify such a hope.
Maciej W. Rozycki [Fri, 9 Aug 2024 13:24:51 +0000 (14:24 +0100)]
PCI: Revert to the original speed after PCIe failed link retraining
When `pcie_failed_link_retrain' has failed to retrain the link by hand
it leaves the link speed restricted to 2.5GT/s, which will then affect
any device that has been plugged in later on, which may not suffer from
the problem that caused the speed restriction to have been attempted.
Consequently such a downstream device will suffer from an unnecessary
communication throughput limitation and therefore performance loss.
Remove the speed restriction then and revert the Link Control 2 register
to its original state if link retraining with the speed restriction in
place has failed. Retrain the link again afterwards so as to remove any
residual state, waiting on LT rather than DLLLA to avoid an excessive
delay and ignoring the result as this training is supposed to fail
anyway.
Maciej W. Rozycki [Fri, 9 Aug 2024 13:24:46 +0000 (14:24 +0100)]
PCI: Clear the LBMS bit after a link retrain
The LBMS bit, where implemented, is set by hardware either in response
to the completion of retraining caused by writing 1 to the Retrain Link
bit or whenever hardware has changed the link speed or width in attempt
to correct unreliable link operation. It is never cleared by hardware
other than by software writing 1 to the bit position in the Link Status
register and we never do such a write.
We currently have two places, namely apply_bad_link_workaround() and
pcie_failed_link_retrain() in drivers/pci/controller/dwc/pcie-tegra194.c
and drivers/pci/quirks.c respectively where we check the state of the LBMS
bit and neither is interested in the state of the bit resulting from the
completion of retraining, both check for a link fault.
And in particular pcie_failed_link_retrain() causes issues consequently, by
trying to retrain a link where there's no downstream device anymore and the
state of 1 in the LBMS bit has been retained from when there was a device
downstream that has since been removed.
Clear the LBMS bit then at the conclusion of pcie_retrain_link(), so that
we have a single place that controls it and that our code can track link
speed or width changes resulting from unreliable link operation.
Jim Quinlan [Thu, 15 Aug 2024 22:57:23 +0000 (18:57 -0400)]
PCI: brcmstb: Refactor for chips with many regular inbound windows
Provide support for new chips with multiple inbound windows while
keeping the legacy support for the older chips.
In existing chips there are three inbound windows with fixed purposes:
the first was for mapping SoC internal registers, the second was for
memory, and the third was for memory but with the endian swapped.
Typically, only one window was used.
Complicating the inbound window usage was the fact that the PCIe HW
would do a baroque internal mapping of system memory, and concatenate
the regions of multiple memory controllers.
Newer chips such as the 7712 and Cable Modem SoCs take a step forward
and drop the internal mapping while providing for multiple inbound
windows. This works in concert with the dma-ranges property, where each
provided range becomes an inbound window.
The PCIe SSD Status LED Management _DSM defined in PCI Firmware Spec r3.3
sec 4.7 provides a way to manage LEDs via ACPI.
The design is similar to NPEM defined in PCIe Base Specification r6.1 sec
6.28:
- Both standards are indication oriented,
- _DSM supported bits correspond to NPEM capability register bits,
- _DSM control bits correspond to NPEM control register bits.
_DSM does not support enclosure-specific indications or the special NPEM
commands NPEM_ENABLE and NPEM_RESET.
_DSM is implemented as a second backend in NPEM driver. The backend used is
logged with info priority. The same sysfs interface is used for both NPEM
and _DSM.
According to spec, _DSM has higher priority, and availability of _DSM in
not limited to devices with NPEM support.
The Dell implementation of DSM uses acpi ipmi, which may not be available
immediately (in fact it may take up to 10s for this interface to be
available). It can determine if DSM is supported (GET_SUPPORTED_STATES_DSM
is working) but it cannot serve GET_STATE_DSM or SET_STATE_DSM commands in
this time.
From userspace application perspective (primarily configured by systemd
service) it is better to have not working but configured interface rather
than have it available after few seconds.
For that reason, npem->active_indications cache is now loaded lazily, i.e.
any GET or SET request want cache to be updated if it is not done yet.
Link: https://lore.kernel.org/r/20240904104848.23480-4-mariusz.tkaczyk@linux.intel.com Suggested-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com> Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
PCI/NPEM: Add Native PCIe Enclosure Management support
Native PCIe Enclosure Management (NPEM, PCIe r6.1 sec 6.28) allows managing
LEDs in storage enclosures. NPEM is indication oriented and it does not
give direct access to LEDs. Although each indication *could* represent an
individual LED, multiple indications could also be represented as a single,
multi-color LED or a single LED blinking in a specific interval. The
specification leaves that open.
Each enabled indication (capability register bit on) is represented as a
ledclass_dev which can be controlled through sysfs. For every ledclass
device only 2 brightness states are allowed: LED_ON (1) or LED_OFF (0).
This corresponds to the NPEM control register (Indication bit on/off).
Ledclass devices appear in sysfs as child devices (subdirectory) of PCI
device which has an NPEM Extended Capability and indication is enabled in
NPEM capability register. For example, these are LEDs created for pcieport
"10000:02:05.0" on my setup:
They can be also found in "/sys/class/leds" directory. The parent PCIe
device domain/bus/device/function address is used to guarantee uniqueness
across leds subsystem.
To enable/disable a "fail" indication, the "brightness" file can be edited:
PCIe r6.1, sec 7.9.19.2 defines the possible indications.
Multiple indications for same parent PCIe device can conflict and hardware
may update them when processing new request. To avoid issues, driver
refresh all indications by reading back control register.
This driver expects to be the exclusive NPEM extended capability manager.
It waits up to 1 second after imposing new request, it doesn't verify if
controller is busy before write, and it assumes the mutex lock gives
protection from concurrent updates.
If _DSM LED management is available, we assume the platform may be using
NPEM for its own purposes (see PCI Firmware Spec r3.3 sec 4.7), so the
driver does not use NPEM. A future patch will add _DSM support; an info
message notes whether NPEM or _DSM is being used.
NPEM is a PCIe extended capability so it should be registered in
pcie_init_capabilities() but it is not possible due to LED dependency. The
parent pci_device must be added earlier for led_classdev_register() to be
successful. NPEM does not require configuration on kernel side, so it is
safe to register LED devices later.
Link: https://lore.kernel.org/r/20240904104848.23480-3-mariusz.tkaczyk@linux.intel.com Suggested-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
NPEM driver will require leds class, there is an init-order conflict.
Make sure that LEDs initialization happens first and add comment.
Link: https://lore.kernel.org/r/20240904104848.23480-2-mariusz.tkaczyk@linux.intel.com Suggested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Previous commit to this bindings, commit 756485bfbb85 ("dt-bindings:
PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema"), updated the
bindings to specify one interrupt only, as the devicetree at that time
did not describe the hardware fully.
The devicetree for SC7280 now specifies eight interrupts, following the
commit b8ba66b40da3 ("arm64: dts: qcom: sc7280: Add additional MSI
interrupts").
Frank Li [Mon, 1 Jul 2024 22:16:12 +0000 (18:16 -0400)]
dt-bindings: PCI: layerscape-pci: Change property 'fsl,pcie-scfg' type
The fsl,pcie-scfg requires an argument when there are more than one PCIe
instances.
Thus, change it to the phandle-array type and use items to describe
what each field means.
This also fixes the following warning:
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dtb: pcie@3400000: fsl,pcie-scfg:0: [22, 0] is too long from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie.yaml#
Properties with variable number of items per each device are expected to
have widest constraints in top-level "properties:" block and further
customized (narrowed) in "if:then:".
Add missing top-level constraints for clock-names and reset-names.
Properties with variable number of items per each device are expected to
have widest constraints in top-level "properties:" block and further
customized (narrowed) in "if:then:".
Add missing top-level constraints for clocks and clock-names.
Properties with variable number of items per each device are expected to
have widest constraints in top-level "properties:" block and further
customized (narrowed) in "if:then:".
Add missing top-level constraints for clock-names and reset-names.
Jim Quinlan [Thu, 15 Aug 2024 22:57:22 +0000 (18:57 -0400)]
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
Add a "has_phy" field indicating that the internal PHY has SW control
that requires configuration. Some previous chips only required the
firing of the "rescal" reset controller.
This change requires us to give the 7216 SoC its own cfg_data structure.
Jim Quinlan [Thu, 15 Aug 2024 22:57:17 +0000 (18:57 -0400)]
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
Refactor the error handling in the bottom half of the probe function
for readability.
The invocation of clk_prepare_enable() is moved lower in the function
and this simplifies a couple of return paths. The dev_err_probe() is
also used when it is apt.
Add description for the 7712 SoC, a Broadcom STB sibling chip
of the Raspberry Pi 5.
The 7712 uses three reset controllers: rescal, for PHY reset
calibration; bridge, for the bridge between the PCIe bus and
the memory bus; and swinit, which is a "soft" initialization
of the PCIe HW.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-4-james.quinlan@broadcom.com Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Jim Quinlan [Thu, 15 Aug 2024 22:57:14 +0000 (18:57 -0400)]
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
Change maintainer: Nicolas has not been active for a while. It also
makes sense for a Broadcom employee to be the maintainer as many of the
details are privy to Broadcom.
Also, alphabetize the compatible strings.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-2-james.quinlan@broadcom.com Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log] Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
PCI: cadence: Drop excess cdns_pcie_rc.dev kerneldoc description
Struct cdns_pcie_rc once had a .dev member, but it was removed by bd22885aa188 ("PCI: cadence: Refactor driver to use as a core library").
Drop the extra kerneldoc for it.
Ilpo Järvinen [Thu, 8 Aug 2024 12:17:07 +0000 (15:17 +0300)]
PCI: Wait for Link before restoring Downstream Buses
__pci_reset_bus() calls pci_bridge_secondary_bus_reset() to perform the
reset and also waits for the Secondary Bus to become again accessible.
__pci_reset_bus() then calls pci_bus_restore_locked() that restores the PCI
devices connected to the bus, and if necessary, recursively restores also
the subordinate buses and their devices.
The logic in pci_bus_restore_locked() does not take into account that after
restoring a device on one level, there might be another Link Downstream
that can only start to come up after restore has been performed for its
Downstream Port device. That is, the Link may require additional wait until
it becomes accessible.
Similarly, pci_slot_restore_locked() lacks wait.
Amend pci_bus_restore_locked() and pci_slot_restore_locked() to wait for
the Secondary Bus before recursively performing the restore of that bus.
Philipp Stanner [Wed, 7 Aug 2024 08:30:20 +0000 (10:30 +0200)]
drm/ast: Request PCI BAR with devres
ast currently ioremaps two PCI BARs using pcim_iomap(). It does not perform
a request on the regions, however, which would make the driver a bit more
robust.
PCI now offers pcim_iomap_region(), a managed function which both requests
and ioremaps a BAR.
Replace pcim_iomap() with pcim_iomap_region().
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://lore.kernel.org/r/20240807083018.8734-4-pstanner@redhat.com Signed-off-by: Philipp Stanner <pstanner@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Acked-by: Dave Airlie <airlied@redhat.com>
Philipp Stanner [Wed, 7 Aug 2024 08:30:18 +0000 (10:30 +0200)]
PCI: Deprecate pcim_iomap_regions() in favor of pcim_iomap_region()
pcim_iomap_regions() is a complicated function that uses a bit mask to
determine the BARs the user wishes to request and ioremap. Almost all users
only ever set a single bit in that mask, making that mechanism
questionable.
pcim_iomap_region() is now available as a more simple replacement.
Philipp Stanner [Mon, 29 Jul 2024 09:36:27 +0000 (11:36 +0200)]
drm/vboxvideo: Add PCI region request
vboxvideo currently does not reserve its PCI BAR through a region request.
Implement the request through the managed function pcim_request_region().
Link: https://lore.kernel.org/r/20240729093625.17561-5-pstanner@redhat.com Signed-off-by: Philipp Stanner <pstanner@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
Philipp Stanner [Mon, 29 Jul 2024 09:36:26 +0000 (11:36 +0200)]
PCI: Make pcim_request_region() a public function
pcim_request_region() is the managed counterpart of pci_request_region().
It is currently only used internally for PCI.
It can be useful for a number of drivers and exporting it is a step towards
deprecating more complicated functions.
Make pcim_request_region() a public function.
Link: https://lore.kernel.org/r/20240729093625.17561-4-pstanner@redhat.com Signed-off-by: Philipp Stanner <pstanner@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
Lukas Wunner [Mon, 5 Aug 2024 15:24:05 +0000 (17:24 +0200)]
s390/pci: Stop usurping pdev->dev.groups
Bjorn suggests using pdev->dev.groups for attribute_groups constructed on
PCI device enumeration:
"Is it feasible to build an attribute group in pci_doe_init() and
add it to dev->groups so device_add() will automatically add them?"
https://lore.kernel.org/r/20231019165829.GA1381099@bhelgaas
Unfortunately on s390, pcibios_device_add() usurps pdev->dev.groups for
arch-specific attribute_groups, preventing its use for anything else.
Introduce an ARCH_PCI_DEV_GROUPS macro which arches can define in
<asm/pci.h>. The macro is visible in drivers/pci/pci-sysfs.c through the
inclusion of <linux/pci.h>, which in turn includes <asm/pci.h>.
On s390, define the macro to the three attribute_groups previously assigned
to pdev->dev.groups. Thereby pdev->dev.groups is made available for use by
the PCI core.
As a side effect, arch/s390/pci/pci_sysfs.c no longer needs to be compiled
into the kernel if CONFIG_SYSFS=n.
weiyufeng [Tue, 6 Aug 2024 06:50:50 +0000 (14:50 +0800)]
PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Remove the hpc_ops struct from shpchp. This struct is unnecessary and no
other hotplug controller implements it. A similar thing has already been
done in pciehp with 82a9e79ef132 ("PCI: pciehp: remove hpc_ops").
Marek Vasut [Tue, 23 Jul 2024 13:27:01 +0000 (15:27 +0200)]
genirq/msi: Silence 'set affinity failed' warning
Various PCI controllers that mux MSIs onto a single IRQ line produce these
"IRQ%d: set affinity failed" warnings when entering suspend. This has been
discussed before [1] [2] and an example test case is included at the end of
this commit message.
Controller drivers that create MSI IRQ domain with
MSI_FLAG_USE_DEF_CHIP_OPS and do not override the .irq_set_affinity()
irqchip callback get assigned the default msi_domain_set_affinity()
callback. That is not desired on controllers where it is not possible to
set affinity of each MSI IRQ line to a specific CPU core due to hardware
limitation.
Introduce flag MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset
if the controller driver did not assign it. This way, migrate_one_irq()
can exit right away, without printing the warning. The .irq_set_affinity()
implementations which only return -EINVAL can be removed from multiple
controller drivers.
Merge tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts,
which is an error with the latest Clang
* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix '-S -c' in x86 stack protector scripts
kbuild: rpm-pkg: ghost modules.weakdep file
kbuild: rpm-pkg: Fix C locale setup
minmax: simplify and clarify min_t()/max_t() implementation
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3a7e02c040b1 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
projects / users / jedix / linux-maple.git / log