Alexander Stein [Wed, 10 Jan 2024 10:00:48 +0000 (11:00 +0100)]
arm64: dts: imx8mp: reparent MEDIA_MIPI_PHY1_REF to CLK_24M
This is already done in dsi node, introduced in commit eda09fe149df4
("arm64: dts: imx8mp: Add display pipeline components").
This needs to be applied to csi nodes as well or the clock might be busy
if both csi and dsi nodes are enabled.
Fixes error:
clk: failed to reparent media_mipi_phy1_ref to osc_24m: -16
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Philippe Schenker [Tue, 9 Jan 2024 12:16:27 +0000 (13:16 +0100)]
arm64: dts: imx8mp-verdin: Label ldo5 and link to usdhc2
This commit labels LDO5 as `reg_vdd_sdio` in `imx8mp-verdin.dtsi` to
facilitate changing its voltage to 1.8V, necessary for an SDIO
peripheral that requires 1.8V at default and high-speed modes.
Additionally, it links `reg_vdd_sdio` to `&usdhc2`, aligning with the
hardware configuration specified in the datasheet.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DTSI for Variscite VAR-SOM-MX93 System on Module and DTS for Variscite
VAR-SOM-MX93 on Symphony evaluation board.
This version comes with:
- NXP i.MX 93 Dual, 1.7GHz, Cortex-A55 + Cortex-M33
- 2 GB of RAM
- 16GB eMMC
- 802.11ax/ac/a/b/g/n WiFi with 5.3 Bluetooth
- CAN bus
- Audio codec
Fabio Estevam [Wed, 3 Jan 2024 22:59:42 +0000 (19:59 -0300)]
arm64: dts: ls1046a: Remove big-endian from thermal
Per qoriq-thermal.yaml, 'big-endian' is not a valid property.
When the 'little-endian' property is absent, the default is big endian.
Remove it to fix the following schema warning:
tmu@1f00000: 'big-endian' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/thermal/qoriq-thermal.yaml#
Tim Harvey [Wed, 20 Dec 2023 23:30:46 +0000 (15:30 -0800)]
arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx does not have a gpio controlled vbus regulator but it does
require some pinctrl. Remove the regulator and move the valid pinctrl
into the usbotg1 node.
Fixes: bd306fdb4e60 ("arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS") Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Mon, 18 Dec 2023 14:23:12 +0000 (15:23 +0100)]
arm64: dts: imx8qxp: add GPU nodes
Add the DT node for the GPU core found on the i.MX8QXP.
etnaviv-gpu 53100000.gpu: model: GC7000, revision: 6214
[drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frank Li [Thu, 14 Dec 2023 19:46:55 +0000 (14:46 -0500)]
arm64: dts: imx8qm: Correct edma3 power-domains and interrupt numbers
It is eDMA1 at QM, which have the same register with eDMA3 at qxp.
The below commit fix panic problem.
commit b37e75bddc35 ("arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup")
This fixes the IRQ and DMA channel numbers. While QM eDMA1 technically has
32 channels, only 10 channels are likely used for I2C. The exact IRQ
numbers for the remaining channels were unclear in the reference manual.
Fixes: e4d7a330fb7a ("arm64: dts: imx8: add edma[0..3]") Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 14 Dec 2023 15:02:43 +0000 (16:02 +0100)]
arm64: dts: imx8qxp: mba8xx: Add analog audio output on MBa8Xx
Enable SAI1, add the codec to enable LINE_IN and LINE_OUT support on
MBa8Xx on connectors X9 & X10.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 14 Dec 2023 15:02:42 +0000 (16:02 +0100)]
arm64: dts: imx8qxp: Add mclkout clock gates
These clock gates provide a clock output on ACM_MCLK_OUT pads. They are
intended to be used as MCLK for SAI0-3.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 14 Dec 2023 15:02:41 +0000 (16:02 +0100)]
arm64: dts: imx8qxp: Add audio SAI nodes
This adds the sai nodes attached to aips1 bus. These can be shared with
imx8qm as well. Input clock from ACM is always feed to mclk1 only. Others
are unused and are connected to a dummy clock.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 14 Dec 2023 15:02:40 +0000 (16:02 +0100)]
arm64: dts: imx8qxp: Add audio clock mux node
The audio clock mux (ACM) selects the input clock for each attached
consumer, referenced by clock-cell.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 14 Dec 2023 15:02:39 +0000 (16:02 +0100)]
arm64: dts: imx8qxp: Add ACM input clock gates
These clock gates provide input clocks for ACM. They can be selected by
IMX_ADMA_ACM_* macros. As SAI driver does not provide Tx/Rx bitclock
clocks yet, add dummy clocks for the unimplemented inputs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 1 Feb 2024 09:59:46 +0000 (17:59 +0800)]
arm64: dts: freescale: add initial device tree for TQMa8Xx
This adds support for TQMa8XQP and TQMa8XDP modules on MBa8Xx board.
As the only difference is the mounted SoC, both module and baseboard
files are shared.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 14 Dec 2023 14:23:24 +0000 (15:23 +0100)]
arm64: dts: imx: add imx8dxp support
i.MX 8DualXPlus is a dual (2x) Cortex-A35 processor with powerful
graphic and multimedia features. This patch adds the SoC dtsi, based on
imx8qxp removing the additional CPU cores. Peripherals are identical.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:49:09 +0000 (09:49 +0100)]
arm64: dts: imx8mm-kontron: Refactor devicetree for OSM-S module and board
The OSM spec defines dedicated functions for all pads of the SoM.
Therefore we can assume that carrier board designs stick to these
definitions and extend the SoM devicetree include with matching
default nodes and pinmux settings.
This way we can reduce the overhead and redundancy in the carrier
board devicetrees while still sticking to the policy of separating
board and module description.
Even if the carrier board design deviates slightly from the spec it
can define its own pinmux definitions and use them as necessary or
even disable unused nodes from the SoM devicetree.
Frieder Schrempf [Mon, 8 Jan 2024 08:49:05 +0000 (09:49 +0100)]
arm64: dts: imx8mm-kontron: Fix OSM-S devicetrees to match latest hardware
The current state of the devicetree for the i.MX8MM OSM-S and the BL
baseboard reflects deprecated prototype hardware. Update the board
description to match the latest hardware revision.
As the old hardware is not available anymore, was only produced in
very small quantities and was broken in some ways, we can safely
fixup the original devicetree.
Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:49:03 +0000 (09:49 +0100)]
arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL board
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:49:02 +0000 (09:49 +0100)]
arm64: dts: imx8mm-kontron: Disable pull resistors for SD card signals on BL OSM-S board
Some signals have external pullup resistors on the board and don't need
the internal ones to be enabled. Due to silicon errata ERR050080 let's
disable the internal pull resistors whererever possible and prevent
any unwanted behavior in case they wear out.
Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:49:01 +0000 (09:49 +0100)]
arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL board
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:49:00 +0000 (09:49 +0100)]
arm64: dts: imx8mm-kontron: Disable pullups for onboard UART signals on BL OSM-S board
These signals are actively driven by the SoC or by the onboard
transceiver. There's no need to enable the internal pull resistors
and due to silicon errata ERR050080 let's disable the internal ones
to prevent any unwanted behavior in case they wear out.
Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:48:59 +0000 (09:48 +0100)]
arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on SL/BL i.MX8MM
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Mon, 8 Jan 2024 08:48:58 +0000 (09:48 +0100)]
arm64: dts: imx8mm-kontron: Disable pullups for I2C signals on OSM-S i.MX8MM
There are external pullup resistors on the board and due to silicon
errata ERR050080 let's disable the internal ones to prevent any
unwanted behavior in case they wear out.
Fixes: de9618e84f76 ("arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 21 Jan 2024 22:01:12 +0000 (14:01 -0800)]
Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs
Pull more bcachefs updates from Kent Overstreet:
"Some fixes, Some refactoring, some minor features:
- Assorted prep work for disk space accounting rewrite
- BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
makes our trigger context more explicit
- A few fixes to avoid excessive transaction restarts on
multithreaded workloads: fstests (in addition to ktest tests) are
now checking slowpath counters, and that's shaking out a few bugs
- Assorted tracepoint improvements
- Starting to break up bcachefs_format.h and move on disk types so
they're with the code they belong to; this will make room to start
documenting the on disk format better.
- A few minor fixes"
* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
bcachefs: Improve inode_to_text()
bcachefs: logged_ops_format.h
bcachefs: reflink_format.h
bcachefs; extents_format.h
bcachefs: ec_format.h
bcachefs: subvolume_format.h
bcachefs: snapshot_format.h
bcachefs: alloc_background_format.h
bcachefs: xattr_format.h
bcachefs: dirent_format.h
bcachefs: inode_format.h
bcachefs; quota_format.h
bcachefs: sb-counters_format.h
bcachefs: counters.c -> sb-counters.c
bcachefs: comment bch_subvolume
bcachefs: bch_snapshot::btime
bcachefs: add missing __GFP_NOWARN
bcachefs: opts->compression can now also be applied in the background
bcachefs: Prep work for variable size btree node buffers
bcachefs: grab s_umount only if snapshotting
...
Linus Torvalds [Sun, 21 Jan 2024 19:14:40 +0000 (11:14 -0800)]
Merge tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers"
* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
clocksource/drivers/ep93xx: Fix error handling during probe
clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
clocksource/timer-riscv: Add riscv_clock_shutdown callback
dt-bindings: timer: Add StarFive JH8100 clint
dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
Kent Overstreet [Tue, 16 Jan 2024 21:20:21 +0000 (16:20 -0500)]
bcachefs: opts->compression can now also be applied in the background
The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Tue, 16 Jan 2024 18:29:59 +0000 (13:29 -0500)]
bcachefs: Prep work for variable size btree node buffers
bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.
And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.
Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
In __bch2_ioctl_subvolume_create(), we grab s_umount unconditionally
and unlock it at the end of the function. There is a comment
"why do we need this lock?" about the lock coming from
commit 42d237320e98 ("bcachefs: Snapshot creation, deletion")
The reason is that __bch2_ioctl_subvolume_create() calls
sync_inodes_sb() which enforce locked s_umount to writeback all dirty
nodes before doing snapshot works.
Fix it by read locking s_umount for snapshotting only and unlocking
s_umount after sync_inodes_sb().
Signed-off-by: Su Yue <glass.su@suse.com> Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Colin Ian King [Tue, 16 Jan 2024 11:07:23 +0000 (11:07 +0000)]
bcachefs: remove redundant variable tmp
The variable tmp is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so tmp can be
removed.
Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the enclosing
expression, the value is never actually read from 'ret'
[deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Tue, 16 Jan 2024 01:37:23 +0000 (20:37 -0500)]
bcachefs: Fix excess transaction restarts in __bchfs_fallocate()
drop_locks_do() should not be used in a fastpath without first trying
the do in nonblocking mode - the unlock and relock will cause excessive
transaction restarts and potentially livelocking with other threads that
are contending for the same locks.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Mon, 15 Jan 2024 22:59:51 +0000 (17:59 -0500)]
bcachefs: Better journal tracepoints
Factor out bch2_journal_bufs_to_text(), and use it in the
journal_entry_full() tracepoint; when we can't get a journal reservation
we need to know the outstanding journal entry sizes to know if the
problem is due to excessive flushing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Mon, 15 Jan 2024 22:56:22 +0000 (17:56 -0500)]
bcachefs: Avoid flushing the journal in the discard path
When issuing discards, we may need to flush the journal if there's too
many buckets that can't be discarded until a journal flush.
But the heuristic was bad; we should be comparing the number of buckets
that need to flushes against the number of free buckets, not the number
of buckets we saw.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Mon, 15 Jan 2024 19:15:26 +0000 (14:15 -0500)]
bcachefs: bch2_kthread_io_clock_wait() no longer sleeps until full amount
Drop t he loop in bch2_kthread_io_clock_wait(): this allows the code
that uses it to be woken up for other reasons, and fixes a bug where
rebalance wouldn't wake up when a scan was requested.
This raises the possibility of spurious wakeups, but callers should
always be able to handle that reasonably well.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Thu, 11 Jan 2024 04:47:04 +0000 (23:47 -0500)]
bcachefs: Reduce would_deadlock restarts
We don't have to take locks in any particular ordering - we'll make
forward progress just fine - but if we try to stick to an ordering, it
can help to avoid excessive would_deadlock transaction restarts.
This tweaks the reflink path to take extents btree locks in the right
order.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Thu, 11 Jan 2024 04:08:30 +0000 (23:08 -0500)]
bcachefs: Don't log errors if BCH_WRITE_ALLOC_NOWAIT
Previously, we added logging in the write path to ensure that any
unexpected errors getting reported to userspace have a log message; but
BCH_WRITE_ALLOC_NOWAIT is a special case, it's used for promotes where
errors are expected and not reported out to userspace - so we need to
silence those.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
- retry (reconnect) improvement including new retrans mount parm, and
handling of two additional return codes that need to be retried on
- two minor cleanup patches and another to remove duplicate query
info code
- two documentation cleanup, and one reviewer email correction"
* tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update iface_last_update on each query-and-update
cifs: handle servers that still advertise multichannel after disabling
cifs: new mount option called retrans
cifs: reschedule periodic query for server interfaces
smb: client: don't clobber ->i_rdev from cached reparse points
smb: client: get rid of smb311_posix_query_path_info()
smb: client: parse owner/group when creating reparse points
smb: client: fix parsing of SMB3.1.1 POSIX create context
cifs: update known bugs mentioned in kernel docs for cifs
cifs: new nt status codes from MS-SMB2
cifs: pick channel for tcon and tdis
cifs: open_cached_dir should not rely on primary channel
smb3: minor documentation updates
Update MAINTAINERS email address
cifs: minor comment cleanup
smb3: show beginning time for per share stats
cifs: remove redundant variable tcon_exist
Linus Torvalds [Sat, 20 Jan 2024 23:03:25 +0000 (15:03 -0800)]
Merge tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- Loongson LS2X APB DMA controller
- sf-pdma: mpfs-pdma support
- Qualcomm X1E80100 GPI dma controller support
Updates:
- Xilinx XDMA updates to support interleaved DMA transfers
- TI PSIL threads for AM62P and J722S and cfg register regions
description
- axi-dmac Improving the cyclic DMA transfers
- Tegra Support dma-channel-mask property
- Remaining platform remove callback returning void conversions
Driver fixes for:
- Xilinx xdma driver operator precedence and initialization fix
- Excess kernel-doc warning fix in imx-sdma xilinx xdma drivers
- format-overflow warning fix for rz-dmac, sh usb dmac drivers
- 'output may be truncated' fix for shdma, fsl-qdma and dw-edma
drivers"
* tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (58 commits)
dmaengine: dw-edma: increase size of 'name' in debugfs code
dmaengine: fsl-qdma: increase size of 'irq_name'
dmaengine: shdma: increase size of 'dev_id'
dmaengine: xilinx: xdma: Fix kernel-doc warnings
dmaengine: usb-dmac: Avoid format-overflow warning
dmaengine: sh: rz-dmac: Avoid format-overflow warning
dmaengine: imx-sdma: fix Excess kernel-doc warnings
dmaengine: xilinx: xdma: Fix initialization location of desc in xdma_channel_isr()
dmaengine: xilinx: xdma: Fix operator precedence in xdma_prep_interleaved_dma()
dmaengine: xilinx: xdma: statify xdma_prep_interleaved_dma
dmaengine: xilinx: xdma: Workaround truncation compilation error
dmaengine: pl330: issue_pending waits until WFP state
dmaengine: xilinx: xdma: Implement interleaved DMA transfers
dmaengine: xilinx: xdma: Prepare the introduction of interleaved DMA transfers
dmaengine: xilinx: xdma: Add transfer error reporting
dmaengine: xilinx: xdma: Add error checking in xdma_channel_isr()
dmaengine: xilinx: xdma: Rework xdma_terminate_all()
dmaengine: xilinx: xdma: Ease dma_pool alignment requirements
dmaengine: xilinx: xdma: Add necessary macro definitions
dmaengine: xilinx: xdma: Get rid of unused code
...
Linus Torvalds [Sat, 20 Jan 2024 22:20:34 +0000 (14:20 -0800)]
Merge tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccinelle updates from Julia Lawall:
"Updates to the device_attr_show semantic patch to reflect the new
guidelines of the Linux kernel documentation.
The problem was identified by Li Zhijian <lizhijian@fujitsu.com>, who
proposed an initial fix"
* tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
coccinelle: device_attr_show: simplify patch case
coccinelle: device_attr_show: Adapt to the latest Documentation/filesystems/sysfs.rst
Aurelien Jarno [Sat, 13 Jan 2024 18:33:31 +0000 (19:33 +0100)]
media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)
This patch replaces max(a, min(b, c)) by clamp(b, a, c) in the solo6x10
driver. This improves the readability and more importantly, for the
solo6x10-p2m.c file, this reduces on my system (x86-64, gcc 13):
- the preprocessed size from 121 MiB to 4.5 MiB;
- the build CPU time from 46.8 s to 1.6 s;
- the build memory from 2786 MiB to 98MiB.
In fine, this allows this relatively simple C file to be built on a
32-bit system.
Reported-by: Jiri Slaby <jirislaby@gmail.com> Closes: https://lore.kernel.org/lkml/18c6df0d-45ed-450c-9eda-95160a2bbb8e@gmail.com/ Cc: <stable@vger.kernel.org> # v6.7+ Suggested-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: David Laight <David.Laight@ACULAB.COM> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 9 Jan 2024 00:43:04 +0000 (16:43 -0800)]
execve: open the executable file before doing anything else
No point in allocating a new mm, counting arguments and environment
variables etc if we're just going to return ENOENT.
This patch does expose the fact that 'do_filp_open()' that execve() uses
is still unnecessarily expensive in the failure case, because it
allocates the 'struct file *' early, even if the path lookup (which is
heavily optimized) fails.
So that remains an unnecessary cost in the "no such executable" case,
but it's a separate issue. Regardless, I do not want to do _both_ a
filename_lookup() and a later do_filp_open() like the origin patch by
Josh Triplett did in [1].
Linus Torvalds [Sat, 20 Jan 2024 19:06:04 +0000 (11:06 -0800)]
Merge tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
Linus Torvalds [Sat, 20 Jan 2024 17:42:32 +0000 (09:42 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Final round of fixes that came in too late to send in the first
request.
It's nine bug fixes and one version update (because of a bug fix) and
one set of PCI ID additions. There's one bug fix in the core which is
really a one liner (except that an additional sdev pointer was added
for convenience) and the rest are in drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Add TMF to tmr_list handling
scsi: core: Kick the requeue list after inserting when flushing
scsi: fnic: unlock on error path in fnic_queuecommand()
scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
scsi: smartpqi: Bump driver version to 2.1.26-030
scsi: smartpqi: Fix logical volume rescan race condition
scsi: smartpqi: Add new controller PCI IDs
scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
scsi: ufs: core: Simplify power management during async scan
Linus Torvalds [Sat, 20 Jan 2024 17:24:06 +0000 (09:24 -0800)]
Merge tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Since the large patch series to convert arch/sh to device tree support
has not been finalized yet due to various maintainers still asking for
changes to the series, this ended up being rather small consisting of
just two fixes.
The first patch by Geert Uytterhoeven addresses a build failure in the
EcoVec platform code. And the second patch by Masahiro Yamada removes
an unnecessary $(foreach ...) found in a Makefile of the vsyscall
code.
- Rename missed backlight field from fbdev to dev
- Remove unnecessary $(foreach ...)"
* tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: vsyscall: Remove unnecessary $(foreach ...)
sh: ecovec24: Rename missed backlight field from fbdev to dev
Linus Torvalds [Sat, 20 Jan 2024 17:14:04 +0000 (09:14 -0800)]
Merge tag 'fbdev-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fix from Helge Deller:
"There were various reports from people without any graphics output on
the screen and it turns out one commit triggers the problem.
- Revert 'firmware/sysfb: Clear screen_info state after consuming it'"
* tag 'fbdev-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
Revert "firmware/sysfb: Clear screen_info state after consuming it"
Linus Torvalds [Fri, 19 Jan 2024 22:25:23 +0000 (14:25 -0800)]
Merge tag 'perf-tools-for-v6.8-1-2024-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools updates from Arnaldo Carvalho de Melo:
"Add Namhyung Kim as tools/perf/ co-maintainer, we're taking turns
processing patches, switching roles from perf-tools to perf-tools-next
at each Linux release.
Data profiling:
- Associate samples that identify loads and stores with data
structures. This uses events available on Intel, AMD and others and
DWARF info:
# To get memory access samples in kernel for 1 second (on Intel)
$ perf mem record -a -K --ldlat=4 -- sleep 1
# Similar for the AMD (but it requires 6.3+ kernel for BPF filters)
$ perf mem record -a --filter 'mem_op == load || mem_op == store, ip > 0x8000000000000000' -- sleep 1
Then, amongst several modes of post processing, one can do things like:
This uses the existing annotate code, calling objdump to do the
disassembly, with improvements to avoid having this take too long,
but longer term a switch to a disassembler library, possibly
reusing code in the kernel will be pursued.
This is the initial implementation, please use it and report
impressions and bugs. Make sure the kernel-debuginfo packages match
the running kernel. The 'perf report' phase for non short perf.data
files may take a while.
There is a great article about it on LWN:
https://lwn.net/Articles/955709/ - "Data-type profiling for perf"
One last test I did while writing this text, on a AMD Ryzen 5950X,
using a distro kernel, while doing a simple 'find /' on an
otherwise idle system resulted in:
- Add s390 raw data interpretation for PAI (Processor Activity
Instrumentation) counters.
perf archive:
- Add new option '--all' to pack perf.data with DSOs.
- Add new option '--unpack' to expand tarballs.
Initialization speedups:
- Lazily initialize zstd streams to save memory when not using it.
- Lazily allocate/size mmap event copy.
- Lazy load kernel symbols in 'perf record'.
- Be lazier in allocating lost samples buffer in 'perf record'.
- Don't synthesize BPF events when disabled via the command line
(perf record --no-bpf-event).
Assorted improvements:
- Show note on AMD systems that the :p, :pp, :ppp and :P are all the
same, as IBS (Instruction Based Sampling) is used and it is
inherentely precise, not having levels of precision like in Intel
systems.
- When 'cycles' isn't available, fall back to the "task-clock" event
when not system wide, not to 'cpu-clock'.
- Add --debug-file option to redirect debug output, e.g.:
$ perf --debug-file /tmp/perf.log record -v true
- Shrink 'struct map' to under one cacheline by avoiding function
pointers for selecting if addresses are identity or DSO relative,
and using just a byte for some boolean struct members.
- Resolve the arch specific strerrno just once to use in
perf_env__arch_strerrno().
- Reduce memory for recording PERF_RECORD_LOST_SAMPLES event.
Assorted fixes:
- Fix the default 'perf top' usage on Intel hybrid systems, now it
starts with a browser showing the number of samples for Efficiency
(cpu_atom/cycles/P) and Performance (cpu_core/cycles/P). This
behaviour is similar on ARM64, with its respective set of
big.LITTLE processors.
- Fix segfault on build_mem_topology() error path.
- Fix 'perf mem' error on hybrid related to availability of mem event
in a PMU.
- Fix missing reference count gets (map, maps) in the db-export code.
- Avoid recursively taking env->bpf_progs.lock in the 'perf_env'
code.
- Use the newly introduced maps__for_each_map() to add missing
locking around iteration of 'struct map' entries.
- Parse NOTE segments until the build id is found, don't stop on the
first one, ELF files may have several such NOTE segments.
- Remove 'egrep' usage, its deprecated, use 'grep -E' instead.
- Warn first about missing libelf, not libbpf, that depends on
libelf.
- Use alternative to 'find ... -printf' as this isn't supported in
busybox.
- Address python 3.6 DeprecationWarning for string scapes.
- Fix memory leak in uniq() in libsubcmd.
- Fix man page formatting for 'perf lock'
- Fix some spelling mistakes.
perf tests:
- Fail shell tests that needs some symbol in perf itself if it is
stripped. These tests check if a symbol is resolved, if some hot
function is indeed detected by profiling, etc.
- The 'perf test sigtrap' test is currently failing on PREEMPT_RT,
skip it if sleeping spinlocks are detected (using BTF) and point to
the mailing list discussion about it. This test is also being
skipped on several architectures (powerpc, s390x, arm and aarch64)
due to other pending issues with intruction breakpoints.
- Adjust test case perf record offcpu profiling tests for s390.
- Fix 'Setup struct perf_event_attr' fails on s390 on z/VM guest,
addressing issues caused by the fallback from cycles to task-clock
done in this release.
- Fix mask for VG register in the user-regs test.
- Use shellcheck on 'perf test' shell scripts automatically to make
sure changes don't introduce things it flags as problematic.
- Add option to change objdump binary and allow it to be set via
'perf config'.
- Add basic 'perf script', 'perf list --json" and 'perf diff' tests.
- Basic branch counter support.
- Make DSO tests a suite rather than individual.
- Remove atomics from test_loop to avoid test failures.
- Fix call chain match on powerpc for the record+probe_libc_inet_pton
test.
- Improve Intel hybrid tests.
Vendor event files (JSON):
powerpc:
- Update datasource event name to fix duplicate events on IBM's
Power10.
- Add PVN for HX-C2000 CPU with Power8 Architecture.
Intel:
- Alderlake/rocketlake metric fixes.
- Update emeraldrapids events to v1.02.
- Update icelakex events to v1.23.
- Update sapphirerapids events to v1.17.
- Add skx, clx, icx and spr upi bandwidth metric.
AMD:
- Add Zen 4 memory controller events.
RISC-V:
- Add StarFive Dubhe-80 and Dubhe-90 JSON files.
https://www.starfivetech.com/en/site/cpu-u
Linus Torvalds [Fri, 19 Jan 2024 21:49:16 +0000 (13:49 -0800)]
Merge tag 'strlcpy-removal-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull strlcpy removal from Kees Cook:
"As promised, this is 'part 2' of the hardening tree, late in -rc1 now
that all the other trees with strlcpy() removals have landed. One new
user appeared (in bcachefs) but was a trivial refactor. The kernel is
now free of the strlcpy() API!
- Remove of the final (very recent) user of strlcpy() (in bcachefs)
- Remove the strlcpy() API. Long live strscpy()"
* tag 'strlcpy-removal-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
string: Remove strlcpy()
bcachefs: Replace strlcpy() with strscpy()
Linus Torvalds [Fri, 19 Jan 2024 21:36:15 +0000 (13:36 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"I think the main one is fixing the dynamic SCS patching when full LTO
is enabled (clang was silently getting this horribly wrong), but it's
all good stuff.
Rob just pointed out that the fix to the workaround for erratum
#2966298 might not be necessary, but in the worst case it's harmless
and since the official description leaves a little to be desired here,
I've left it in.
Summary:
- Fix shadow call stack patching with LTO=full
- Fix voluntary preemption of the FPSIMD registers from assembly code
- Fix workaround for A520 CPU erratum #2966298 and extend to A510
- Fix SME issues that resulted in corruption of the register state
- Minor fixes (missing includes, formatting)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix silcon-errata.rst formatting
arm64/sme: Always exit sme_alloc() early with existing storage
arm64/fpsimd: Remove spurious check for SVE support
arm64/ptrace: Don't flush ZA/ZT storage when writing ZA via ptrace
arm64: entry: simplify kernel_exit logic
arm64: entry: fix ARM64_WORKAROUND_SPECULATIVE_UNPRIV_LOAD
arm64: errata: Add Cortex-A510 speculative unprivileged load workaround
arm64: Rename ARM64_WORKAROUND_2966298
arm64: fpsimd: Bring cond_yield asm macro in line with new rules
arm64: scs: Work around full LTO issue with dynamic SCS
arm64: irq: include <linux/cpumask.h>
Linus Torvalds [Fri, 19 Jan 2024 21:30:49 +0000 (13:30 -0800)]
Merge tag 'loongarch-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Raise minimum clang version to 18.0.0
- Enable initial Rust support for LoongArch
- Add built-in dtb support for LoongArch
- Use generic interface to support crashkernel=X,[high,low]
- Some bug fixes and other small changes
- Update the default config file.
* tag 'loongarch-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: (22 commits)
MAINTAINERS: Add BPF JIT for LOONGARCH entry
LoongArch: Update Loongson-3 default config file
LoongArch: BPF: Prevent out-of-bounds memory access
LoongArch: BPF: Support 64-bit pointers to kfuncs
LoongArch: Fix definition of ftrace_regs_set_instruction_pointer()
LoongArch: Use generic interface to support crashkernel=X,[high,low]
LoongArch: Fix and simplify fcsr initialization on execve()
LoongArch: Let cores_io_master cover the largest NR_CPUS
LoongArch: Change SHMLBA from SZ_64K to PAGE_SIZE
LoongArch: Add a missing call to efi_esrt_init()
LoongArch: Parsing CPU-related information from DTS
LoongArch: dts: DeviceTree for Loongson-2K2000
LoongArch: dts: DeviceTree for Loongson-2K1000
LoongArch: dts: DeviceTree for Loongson-2K0500
LoongArch: Allow device trees be built into the kernel
dt-bindings: interrupt-controller: loongson,liointc: Fix dtbs_check warning for interrupt-names
dt-bindings: interrupt-controller: loongson,liointc: Fix dtbs_check warning for reg-names
dt-bindings: loongarch: Add Loongson SoC boards compatibles
dt-bindings: loongarch: Add CPU bindings for LoongArch
LoongArch: Enable initial Rust support
...
Jens Axboe reported a regression that his machine is failing to show a
console, or in fact anything, on current -git. There's no output and no
console after:
Loading Linux 6.7.0+ ...
Loading initial ramdisk ...
Linus Torvalds [Fri, 19 Jan 2024 21:00:45 +0000 (13:00 -0800)]
Merge tag 'devicetree-for-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree header detangling from Rob Herring:
"Remove the circular including of of_device.h and of_platform.h along
with all of their implicit includes.
This is the culmination of several kernel cycles worth of fixing
implicit DT includes throughout the tree"
* tag 'devicetree-for-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Stop circularly including of_device.h and of_platform.h
clk: qcom: gcc-x1e80100: Replace of_device.h with explicit includes
thermal: loongson2: Replace of_device.h with explicit includes
net: can: Use device_get_match_data()
sparc: Use device_get_match_data()
Li Zhijian [Fri, 19 Jan 2024 06:20:57 +0000 (14:20 +0800)]
coccinelle: device_attr_show: Adapt to the latest Documentation/filesystems/sysfs.rst
Adapt description, warning message and MODE=patch according to the latest
Documentation/filesystems/sysfs.rst:
> show() should only use sysfs_emit() or sysfs_emit_at() when formatting
> the value to be returned to user space.
After this patch:
When MODE=report,
$ make coccicheck COCCI=scripts/coccinelle/api/device_attr_show.cocci M=drivers/hid/hid-picolcd_core.c MODE=report
<...snip...>
drivers/hid/hid-picolcd_core.c:304:8-16: WARNING: please use sysfs_emit or sysfs_emit_at
drivers/hid/hid-picolcd_core.c:259:9-17: WARNING: please use sysfs_emit or sysfs_emit_at
CC: Julia Lawall <Julia.Lawall@inria.fr> CC: Nicolas Palix <nicolas.palix@imag.fr> CC: cocci@inria.fr Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Linus Torvalds [Fri, 19 Jan 2024 20:50:09 +0000 (12:50 -0800)]
Merge tag 'spi-fix-v6.8-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"One simple fix for the device unbind path in the Coldfire driver.
A conversion to use a combined get/enable helper missed removing a
disable"
* tag 'spi-fix-v6.8-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: coldfire-qspi: Remove an erroneous clk_disable_unprepare() from the remove function
projects / users / hch / block.git / log