Wayne Tung [Mon, 1 Jul 2024 07:32:52 +0000 (15:32 +0800)]
hwmon: (adt7475) Fix default duty on fan is disabled
According to the comments on fan is disabled, we change to manual mode
and set the duty cycle to 0.
For setting the duty cycle part, the register is wrong. Fix it.
Guenter Roeck [Sun, 30 Jun 2024 20:08:40 +0000 (13:08 -0700)]
hwmon: (jc42) Strengthen detect function
Configuration register bit 5 must read 0 for all JC42.4 compliant chips.
Several capability register bits must be set for all TSE2004 compliant
chips. Use that information to strengthen the detect function.
Guenter Roeck [Sun, 30 Jun 2024 16:32:10 +0000 (09:32 -0700)]
hwmon: (jc42) Use common device ID for TSE2004av compliant sensors
TSE2004av standardizes the device ID of compliant temperature sensors to
be 0x22xx, where xx is the device revision. Use a single define for all
TSE2004av compliant temperature sensors, and relax the device id mask to
match the upper 8 bit of the device id register.
Armin Wolf [Fri, 28 Jun 2024 21:47:23 +0000 (23:47 +0200)]
hwmon: (dell-smm) Add Dell OptiPlex 7060 to DMI table
The BIOS on this machine is buggy and will in some cases return
an error when trying to get the fan state, but reading of the
RPM values and the temperature sensors still works.
Guenter Roeck [Fri, 14 Jun 2024 15:27:21 +0000 (08:27 -0700)]
hwmon: (spd5118) Add support for Renesas/ITD SPD5118 hub controllers
The SPD5118 specification says, in its documentation of the page bits
in the MR11 register:
"
This register only applies to non-volatile memory (1024) Bytes) access of
SPD5 Hub device.
For volatile memory access, this register must be programmed to '000'.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"
Renesas/ITD SPD5118 hub controllers take this literally and disable access
to volatile memory if the page selected in MR11 is != 0. Since the BIOS or
ROMMON will access the non-volatile memory and likely select a page != 0,
this means that the driver will not instantiate since it can not identify
the chip. Even if the driver instantiates, access to volatile registers
is blocked after a nvram read operation which selects a page other than 0.
To solve the problem, add initialization code to select page 0 during
probe. Before doing that, use basic validation to ensure that this is
really a SPD5118 device and not some random EEPROM.
Cc: Sasha Kozachuk <skozachuk@google.com> Cc: John Hamrick <johnham@google.com> Cc: Chris Sarra <chrissarra@google.com> Tested-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stanislav Jakubek [Mon, 17 Jun 2024 16:36:29 +0000 (18:36 +0200)]
dt-bindings: hwmon: ti,tmp108: document V+ supply, add short description
TMP108 is powered by its V+ supply, document it. The property is called
"vcc-supply" since the plus sign (+) is not an expected character.
While at it, add a short description with a link to its datasheets.
Amna Waseem [Tue, 11 Jun 2024 09:36:26 +0000 (11:36 +0200)]
hwmon: (ina2xx) Add device tree support to pass alert polarity
The INA230 has an Alert pin which is asserted when the alert
function selected in the Mask/Enable register exceeds the
value programmed into the Alert Limit register. Assertion is based
on the Alert Polarity Bit (APOL, bit 1 of the Mask/Enable register).
It is default set to value 0 i.e Normal (active-low open collector).
However, hardware can be designed in such a way that expects Alert pin
to become active high if a user-defined threshold in Alert limit
register has been exceeded. This patch adds a way to pass alert polarity
value to the driver via device tree.
Add a property to the binding to configure the Alert Polarity.
Alert pin is asserted based on the value of Alert Polarity bit of
Mask/Enable register. It is by default 0 which means Alert pin is
configured to be active low open collector. Value of 1 maps to
Inverted (active high open collector).
Guenter Roeck [Thu, 6 Jun 2024 16:16:40 +0000 (09:16 -0700)]
hwmon: (pmbus/lm25066) Let enum chips start with index 0
Commit ac0c26bae662 ("hwmon: (lm25066) Use i2c_get_match_data()") changed
enum chips to start with 1 instead of 0, under the assumption that
the data pointer in of_device_id must not start with 0 (NULL) if
i2c_get_match_data() is used. However, that is perfectly fine as long as
there is also an i2c_device_id array with the same data which is used
as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Cc: Rob Herring <robh@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Thu, 6 Jun 2024 16:23:44 +0000 (09:23 -0700)]
hwmon: (nct6775) Let enum kinds start with index 0
Commit 10a0575ea09d ("hwmon: (nct6775-i2c) Use i2c_get_match_data()")
introduced calling i2c_get_match_data() to the nct6775 driver. As part
of that commit, enum kinds was changed to start with 1, based on
Adjust the 'kinds' enum to not use 0, so that no match data can be
distinguished from a valid enum value.
The patch had to be fixed later with commit 2792fc8f8c83 ("hwmon:
(nct6775-core) Explicitly initialize nct6775_device_names indexes") and
commit efe86092ab31 ("hwmon: (nct6775-platform) Explicitly initialize
nct6775_sio_names indexes").
Various patches submitted later show that the change from 0 to 1 is
not really necessary. As it turns out, it is perfectly fine as long as
there is an i2c_device_id array with the same data as in the of_device_id
array. This data is used as fallback if the data pointer in struct
of_device_id is NULL (0).
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Guenter Roeck [Thu, 6 Jun 2024 16:36:38 +0000 (09:36 -0700)]
hwmon: (pmbus/mp2856) Let enum chips start with index 0
Earlier it was assumed that the data pointer in of_device_id must not start
with 0 (NULL) if i2c_get_match_data() is used. However, it turns out that
this is perfectly fine as long as there is also an i2c_device_id array with
the same data, which is used as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
While doing that, remove chip_id from struct mp2856_data since it is only
used in the probe function, and typecast the result of i2c_get_match_data()
to kernel_ulong_t to avoid the double typecast.
Cc: Peter Yin <peteryin.openbmc@gmail.com> Cc: Potin Lai <potin.lai.pt@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Fri, 7 Jun 2024 13:32:04 +0000 (06:32 -0700)]
hwmon: (pmbus/max31827) Explain why enum chips must not start with 0
If a driver calls device_get_match_data(), the .data pointer in its id
data structures must not be NULL/0 because device_get_match_data()
returns NULL if an entry is not found. Explain that in a comment to avoid
confusion why this is required in this driver but not in other drivers.
Cc: Daniel Matyas <daniel.matyas@analog.com> Acked-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Mon, 3 Jun 2024 05:31:52 +0000 (22:31 -0700)]
hwmon: (spd5118) Add configuration option for auto-detection
With SPD5118 chip detection for the most part handled by the i2c-smbus
core using DMI information, the spd5118 driver no longer needs to
auto-detect spd5118 compliant chips.
Auto-detection by the driver is still needed on systems with no DMI support
or on systems with more than eight DIMMs and can not be removed entirely.
However, it affects boot time and introduces the risk of mis-identifying
chips. Add configuration option to be able to disable it on systems where
chip detection is handled outside the driver.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Tested-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Sat, 1 Jun 2024 13:44:47 +0000 (06:44 -0700)]
i2c: smbus: Support DDR5 and LPDDR5 SPD EEPROMs
Detect (LP)DDR5 memory and instantiate the SPD5118 driver automatically.
Suggested-by: Thomas Weißschuh <linux@weissschuh.net> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Thu, 30 May 2024 18:44:11 +0000 (11:44 -0700)]
hwmon: (spd5118) Add suspend/resume support
Add suspend/resume support to ensure that limit and configuration
registers are updated and synchronized after a suspend/resume cycle.
Cc: Armin Wolf <W_Armin@gmx.de> Cc: Stephen Horvath <s.horvath@outlook.com.au> Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Tested-by: Stephen Horvath <s.horvath@outlook.com.au> Tested-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Mon, 27 May 2024 17:49:10 +0000 (10:49 -0700)]
hwmon: Add support for SPD5118 compliant temperature sensors
Add support for SPD5118 (Jedec JESD300) compliant temperature
sensors. Such sensors are typically found on DDR5 memory modules.
Cc: René Rebe <rene@exactcode.de> Cc: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Thomas Weißschuh <linux@weissschuh.net> Tested-by: Thomas Weißschuh <linux@weissschuh.net> Tested-by: Stephen Horvath <s.horvath@outlook.com.au> Tested-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Jeff Johnson [Fri, 7 Jun 2024 22:27:59 +0000 (15:27 -0700)]
hwmon: add missing MODULE_DESCRIPTION() macros
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/asus_atk0110.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/corsair-cpro.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/mr75203.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
Javier Carrasco [Thu, 4 Apr 2024 11:13:28 +0000 (13:13 +0200)]
hwmon: (gsc-hwmon) use device_for_each_child_node_scoped()
Switch to the _scoped() version introduced in commit 365130fd47af
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Javier Carrasco [Thu, 4 Apr 2024 11:13:27 +0000 (13:13 +0200)]
hwmon: (ltc2991) use device_for_each_child_node_scoped()
Switch to the _scoped() version introduced in commit 365130fd47af
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Andrew Davis [Wed, 3 Apr 2024 20:36:33 +0000 (15:36 -0500)]
hwmon: (w83795): Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:32 +0000 (15:36 -0500)]
hwmon: (w83781d) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:31 +0000 (15:36 -0500)]
hwmon: (tmp464) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:30 +0000 (15:36 -0500)]
hwmon: (tmp421) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:29 +0000 (15:36 -0500)]
hwmon: (tmp401) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:28 +0000 (15:36 -0500)]
hwmon: (thmc50) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:27 +0000 (15:36 -0500)]
hwmon: (shtc1) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:26 +0000 (15:36 -0500)]
hwmon: (sht3x) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:25 +0000 (15:36 -0500)]
hwmon: (powr1220) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:24 +0000 (15:36 -0500)]
hwmon: (mcp3021) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:23 +0000 (15:36 -0500)]
hwmon: (max6697) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:22 +0000 (15:36 -0500)]
hwmon: (max1668) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:21 +0000 (15:36 -0500)]
hwmon: (max16065) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:20 +0000 (15:36 -0500)]
hwmon: (lm95234) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:19 +0000 (15:36 -0500)]
hwmon: (lm90) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:18 +0000 (15:36 -0500)]
hwmon: (lm85) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:17 +0000 (15:36 -0500)]
hwmon: (lm83) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:16 +0000 (15:36 -0500)]
hwmon: (lm78) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:15 +0000 (15:36 -0500)]
hwmon: (lm75) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:14 +0000 (15:36 -0500)]
hwmon: (lm63) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:13 +0000 (15:36 -0500)]
hwmon: (ina2xx) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:12 +0000 (15:36 -0500)]
hwmon: (fschmd) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:11 +0000 (15:36 -0500)]
hwmon: (f75375s) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:10 +0000 (15:36 -0500)]
hwmon: (ds1621) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:09 +0000 (15:36 -0500)]
hwmon: (dme1737) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:08 +0000 (15:36 -0500)]
hwmon: (aht10) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:07 +0000 (15:36 -0500)]
hwmon: (adt7475) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:06 +0000 (15:36 -0500)]
hwmon: (ads7828) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:05 +0000 (15:36 -0500)]
hwmon: (adm1031) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:04 +0000 (15:36 -0500)]
hwmon: (adm1021) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Andrew Davis [Wed, 3 Apr 2024 20:36:03 +0000 (15:36 -0500)]
hwmon: (ad7418) Remove use of i2c_match_id()
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Krzysztof Kozlowski [Thu, 6 Jun 2024 14:25:15 +0000 (16:25 +0200)]
hwmon: lm70: simplify with spi_get_device_match_data()
Use spi_get_device_match_data() helper to simplify a bit the driver.
Also kernel_ulong_t type is preferred for kernel code over uintptr_t
(needed for the cast).
Christian Marangi [Tue, 4 Jun 2024 16:43:43 +0000 (18:43 +0200)]
hwmon: g672: add support for g761
Add support for g761 PWM Fan Controller.
The g761 is a copy of the g763 with the only difference of supporting
and internal clock. The internal clock is used if no clocks property is
defined in device node and in such case the required bit is enabled and
clock handling is skipped.
Guenter Roeck [Tue, 28 May 2024 20:33:29 +0000 (13:33 -0700)]
hwmon: Add PEC attribute support to hardware monitoring core
Several hardware monitoring chips optionally support Packet Error Checking
(PEC). For some chips, PEC support can be enabled simply by setting
I2C_CLIENT_PEC in the i2c client data structure. Others require chip
specific code to enable or disable PEC support.
Introduce hwmon_chip_pec and HWMON_C_PEC to simplify adding configurable
PEC support for hardware monitoring drivers. A driver can set HWMON_C_PEC
in its chip information data to indicate PEC support. If a chip requires
chip specific code to enable or disable PEC support, the driver only needs
to implement support for the hwmon_chip_pec attribute to its write
function.
Packet Error Checking is only supported for SMBus devices. HWMON_C_PEC
must therefore only be set by a driver if the parent device is an I2C
device. Attempts to set HWMON_C_PEC on any other device type is not
supported and rejected.
The code calls i2c_check_functionality() to check if PEC is supported
by the I2C/SMBus controller. This function is only available if CONFIG_I2C
is enabled and reachable. For this reason, the added code needs to depend
on reachability of CONFIG_I2C.
Cc: Radu Sabau <radu.sabau@analog.com> Acked-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Aleksandr Mezin [Fri, 24 May 2024 00:39:58 +0000 (03:39 +0300)]
hwmon: (nzxt-smart2) Add support for another version of NZXT RGB & Fan Controller
Add support for NZXT RGB & Fan Controller with USB ID 1e71:2020.
Fan speed control reported to be working with existing userspace (hidraw)
software, so it should be compatible. Fan channel count is the same.
No known differences from already supported devices, at least regarding
fan speed control and initialization.
Wilken Gottwalt [Fri, 24 May 2024 04:38:11 +0000 (04:38 +0000)]
hwmon: corsair-psu: add USB id of HX1200i Series 2023 psu
Add the usb id of the HX1200i Series 2023. Update the documentation
accordingly. Also fix the version comments, there are no Series 2022
products. That are legacy or first version products going back many
many years.
Kent Overstreet [Fri, 24 May 2024 15:42:09 +0000 (11:42 -0400)]
mm: percpu: Include smp.h in alloc_tag.h
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Linus Torvalds [Sun, 26 May 2024 16:54:26 +0000 (09:54 -0700)]
Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com> Cc: Ethan Adams <j.ethan.adams@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Tycho Andersen <tycho@tycho.pizza> Cc: Yang Jihong <yangjihong@bytedance.com> Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Sun, 26 May 2024 05:33:10 +0000 (22:33 -0700)]
Merge tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
Linus Torvalds [Sat, 25 May 2024 22:10:33 +0000 (15:10 -0700)]
Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
Linus Torvalds [Sat, 25 May 2024 21:48:40 +0000 (14:48 -0700)]
Merge tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
Linus Torvalds [Sat, 25 May 2024 21:40:09 +0000 (14:40 -0700)]
Merge tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
crypto: x86/aes-xts - switch to new Intel CPU model defines
x86/topology: Handle bogus ACPI tables correctly
x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
Linus Torvalds [Sat, 25 May 2024 21:23:58 +0000 (14:23 -0700)]
Merge tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A series from Xiubo that adds support for additional access checks
based on MDS auth caps which were recently made available to clients.
This is needed to prevent scenarios where the MDS quietly discards
updates that a UID-restricted client previously (wrongfully) acked to
the user.
Other than that, just a documentation fixup"
* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
doc: ceph: update userspace command to get CephFS metadata
ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
ceph: check the cephx mds auth access for async dirop
ceph: check the cephx mds auth access for open
ceph: check the cephx mds auth access for setattr
ceph: add ceph_mds_check_access() helper
ceph: save cap_auths in MDS client when session is opened
Linus Torvalds [Sat, 25 May 2024 21:19:01 +0000 (14:19 -0700)]
Merge tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"Fixes:
- reusing of the file index (could cause the file to be trimmed)
- infinite dir enumeration
- taking DOS names into account during link counting
- le32_to_cpu conversion, 32 bit overflow, NULL check
- some code was refactored
Changes:
- removed max link count info display during driver init
Remove:
- atomic_open has been removed for lack of use"
* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Break dir enumeration if directory contents error
fs/ntfs3: Fix case when index is reused during tree transformation
fs/ntfs3: Mark volume as dirty if xattr is broken
fs/ntfs3: Always make file nonresident on fallocate call
fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
fs/ntfs3: Use variable length array instead of fixed size
fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
fs/ntfs3: Check 'folio' pointer for NULL
fs/ntfs3: Missed le32_to_cpu conversion
fs/ntfs3: Remove max link count info display during driver init
fs/ntfs3: Taking DOS names into account during link counting
fs/ntfs3: remove atomic_open
fs/ntfs3: use kcalloc() instead of kzalloc()
Linus Torvalds [Sat, 25 May 2024 21:15:39 +0000 (14:15 -0700)]
Merge tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Two ksmbd server fixes, both for stable"
* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: ignore trailing slashes in share paths
ksmbd: avoid to send duplicate oplock break notifications
Linus Torvalds [Sat, 25 May 2024 20:33:53 +0000 (13:33 -0700)]
Merge tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is one new driver and then most of the changes are the device
tree bindings conversions to yaml.
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support"
* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
pcf8563: add wakeup-source support
rtc: rx8111: handle VLOW flag
rtc: rx8111: demote warnings to debug level
rtc: rx6110: Constify struct regmap_config
dt-bindings: rtc: convert trivial devices into dtschema
dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
dt-bindings: rtc: pxa-rtc: convert to dtschema
rtc: Add driver for Epson RX8111
dt-bindings: rtc: Add Epson RX8111
rtc: mcp795: drop unneeded MODULE_ALIAS
rtc: nuvoton: Modify part number value
rtc: test: Split rtc unit test into slow and normal speed test
dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
dt-bindings: rtc: armada-380-rtc: convert to dtschema
rtc: cros-ec: provide ID table for avoiding fallback match
Linus Torvalds [Sat, 25 May 2024 20:28:29 +0000 (13:28 -0700)]
Merge tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Runtime PM (power management) is improved and hot-join support has
been added to the dw controller driver.
Core:
- Allow device driver to trigger controller runtime PM
Drivers:
- dw: hot-join support
- svc: better IBI handling"
* tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: dw: Add hot-join support.
i3c: master: Enable runtime PM for master controller
i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
i3c: master: svc: change ENXIO to EAGAIN when IBI occurs during start frame
i3c: Add comment for -EAGAIN in i3c_device_do_priv_xfers()
Linus Torvalds [Sat, 25 May 2024 20:23:42 +0000 (13:23 -0700)]
Merge tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull jffs2 updates from Richard Weinberger:
- Fix illegal memory access in jffs2_free_inode()
- Kernel-doc fixes
- print symbolic error names
* tag 'jffs2-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: Fix potential illegal address access in jffs2_free_inode
jffs2: Simplify the allocation of slab caches
jffs2: nodemgmt: fix kernel-doc comments
jffs2: print symbolic error name instead of error code
Linus Torvalds [Sat, 25 May 2024 20:17:48 +0000 (13:17 -0700)]
Merge tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML updates from Richard Weinberger:
- Fixes for -Wmissing-prototypes warnings and further cleanup
- Remove callback returning void from rtc and virtio drivers
- Fix bash location
* tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: (26 commits)
um: virtio_uml: Convert to platform remove callback returning void
um: rtc: Convert to platform remove callback returning void
um: Remove unused do_get_thread_area function
um: Fix -Wmissing-prototypes warnings for __vdso_*
um: Add an internal header shared among the user code
um: Fix the declaration of kasan_map_memory
um: Fix the -Wmissing-prototypes warning for get_thread_reg
um: Fix the -Wmissing-prototypes warning for __switch_mm
um: Fix -Wmissing-prototypes warnings for (rt_)sigreturn
um: Stop tracking host PID in cpu_tasks
um: process: remove unused 'n' variable
um: vector: remove unused len variable/calculation
um: vector: fix bpfflash parameter evaluation
um: slirp: remove set but unused variable 'pid'
um: signal: move pid variable where needed
um: Makefile: use bash from the environment
um: Add winch to winch_handlers before registering winch IRQ
um: Fix -Wmissing-prototypes warnings for __warp_* and foo
um: Fix -Wmissing-prototypes warnings for text_poke*
um: Move declarations to proper headers
...
Linus Torvalds [Sat, 25 May 2024 00:28:02 +0000 (17:28 -0700)]
Merge tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
David Howells [Fri, 24 May 2024 14:23:36 +0000 (15:23 +0100)]
cifs: Fix missing set of remote_i_size
Occasionally, the generic/001 xfstest will fail indicating corruption in
one of the copy chains when run on cifs against a server that supports
FSCTL_DUPLICATE_EXTENTS_TO_FILE (eg. Samba with a share on btrfs). The
problem is that the remote_i_size value isn't updated by cifs_setsize()
when called by smb2_duplicate_extents(), but i_size *is*.
This may cause cifs_remap_file_range() to then skip the bit after calling
->duplicate_extents() that sets sizes.
Fix this by calling netfs_resize_file() in smb2_duplicate_extents() before
calling cifs_setsize() to set i_size.
This means we don't then need to call netfs_resize_file() upon return from
->duplicate_extents(), but we also fix the test to compare against the pre-dup
inode size.
[Note that this goes back before the addition of remote_i_size with the
netfs_inode struct. It should probably have been setting cifsi->server_eof
previously.]
Fixes: cfc63fc8126a ("smb3: fix cached file size problems in duplicate extents (reflink)") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev Signed-off-by: Steve French <stfrench@microsoft.com>
David Howells [Wed, 22 May 2024 08:38:48 +0000 (09:38 +0100)]
cifs: Fix smb3_insert_range() to move the zero_point
Fix smb3_insert_range() to move the zero_point over to the new EOF.
Without this, generic/147 fails as reads of data beyond the old EOF point
return zeroes.
Fixes: 3ee1a1fc3981 ("cifs: Cut over to using netfslib") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev Signed-off-by: Steve French <stfrench@microsoft.com>
Chengming Zhou [Mon, 13 May 2024 03:07:56 +0000 (11:07 +0800)]
mm/ksm: fix possible UAF of stable_node
The commit 2c653d0ee2ae ("ksm: introduce ksm_max_page_sharing per page
deduplication limit") introduced a possible failure case in the
stable_tree_insert(), where we may free the new allocated stable_node_dup
if we fail to prepare the missing chain node.
Then that kfolio return and unlock with a freed stable_node set... And
any MM activities can come in to access kfolio->mapping, so UAF.
Fix it by moving folio_set_stable_node() to the end after stable_node
is inserted successfully.
Link: https://lkml.kernel.org/r/20240513-b4-ksm-stable-node-uaf-v1-1-f687de76f452@linux.dev Fixes: 2c653d0ee2ae ("ksm: introduce ksm_max_page_sharing per page deduplication limit") Signed-off-by: Chengming Zhou <chengming.zhou@linux.dev> Acked-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Stefan Roesch <shr@devkernel.io> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
projects / linux.git / log