Merge tag 'tegra-for-6.1-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v6.1-rc1
These changes enable PCI, Ethernet and HDA support on Jetson AGX Orin.
DMA support is enabled for I2C on a number of SoC generations and the
Google Pixel C (a.k.a. Smaug) device receives Bluetooth and Wi-Fi
support.
Other than that this also contains some minor cleanups and fixes.
* tag 'tegra-for-6.1-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add GPCDMA support for Tegra I2C
arm64: tegra: Add iommus for HDA on Tegra234
arm64: tegra: Enable HDA node for Jetson AGX Orin
arm64: tegra: Add context isolation domains on Tegra234
arm64: tegra: Fixup iommu-map property formatting
arm64: dts: tegra: smaug: Add Wi-Fi node
arm64: dts: tegra: smaug: Add Bluetooth node
arm64: tegra: Enable MGBE on Jetson AGX Orin Developer Kit
arm64: tegra: Add MGBE nodes on Tegra234
arm64: tegra: Fix up compatible for Tegra234 GPCDMA
arm64: tegra: Enable PCIe slots in P3737-0000 board
arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT
arm64: tegra: Add regulators required for PCIe
Merge tag 'tegra-for-6.1-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v6.1-rc1
Adds device tree bindings for the MGBE found on Tegra234 SoCs, as well
as stream IDs for the shared host1x context devices.
* tag 'tegra-for-6.1-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Add Host1x context stream IDs on Tegra234
dt-bindings: net: Add Tegra234 MGBE
Merge tag 'at91-dt-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT for v6.1 #2
It contains:
- new SAMA5D3 based board, namely SAMA5D3-EDS
- adjustments to pass the DT binding validations
- disable AES on some LAN966 based boards as they are reserverd by
secure OS
* tag 'at91-dt-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
spi: dt-bindings: atmel,at91rm9200-spi: Add DMA related properties
ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
ARM: dts: at91: sam9x60ek: Add DBGU compatibles to uart1
ARM: dts: at91: sama7g5: Swap rx and tx for spi11
dts: arm: at91: Add SAMA5D3-EDS Board
dt-bindings: arm: at91: Add info on SAMA5D3-EDS
ARM: dts: lan966x: disable aes
spi: dt-bindings: atmel,at91rm9200-spi: Add DMA related properties
The DT nodes of the SPI IP's may contain DMA related properties so
make sure that the binding is able to properly validate those as
well by making it aware of these optional properties.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220913142205.162399-5-sergiu.moga@microchip.com
ARM: dts: at91: sam9x60ek: Add DBGU compatibles to uart1
Maintain consistency among the compatibles of the serial nodes of
sam9x60ek and highlight the incremental characteristic of its serial
IP's by making sure that all serial nodes contain both the sam9x60
and sam9260 usart/dbgu compatibles.
Merge tag 'arm-soc/for-6.1/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoC Device Tree updates
for 6.1, please pull the following:
- Rafal improves the BCM5301X PCIe DT nodes schema validation by
flagging the PCIe controller with a missing "device_type" property
- William merges BCM4908 within BCMBCA since this chip is part of the
Broadcom Broadband Carrier Access group and follows the architecture of
those chips
Mikko Perttunen [Wed, 7 Sep 2022 08:38:44 +0000 (11:38 +0300)]
arm64: tegra: Add context isolation domains on Tegra234
Add Host1x context isolation domains on Tegra234. On Tegra234 we have
two IOMMUs that are connected to Host1x-channel programmed engines,
so we have to include domains for each of them.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
arm64: tegra: Enable PCIe slots in P3737-0000 board
Enable PCIe controller nodes to enable respective PCIe slots on
P3737-0000 board. Following is the ownership of slots by different
PCIe controllers.
Controller-1 : On-board Broadcom WiFi controller
Controller-4 : M.2 Key-M slot
Controller-5 : CEM form-factor x8 slot
arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT
Add P2U (PIPE to UPHY) and PCIe controller nodes to device tree.
The Tegra234 SoC contains 10 PCIe controllers and 24 P2U instances
grouped into three different PHY bricks namely High-Speed IO (HSIO-8 P2Us)
NVIDIA High Speed (NVHS-8 P2Us) and Gigabit Ethernet (GBE-8 P2Us)
respectively.
Mikko Perttunen [Wed, 7 Sep 2022 08:38:43 +0000 (11:38 +0300)]
dt-bindings: Add Host1x context stream IDs on Tegra234
Add defines for stream IDs used for Host1x context isolation
on Tegra234. The same stream IDs are used for both NISO0 and
NISO1 SMMUs since Host1x's stream ID protection tables don't
make a distinction between the two.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
Jerry Ray [Fri, 9 Sep 2022 16:30:22 +0000 (11:30 -0500)]
dts: arm: at91: Add SAMA5D3-EDS Board
The SAMA5D3-EDS board is an Ethernet Development Platform allowing for
evaluating many Microchip ethernet switch and PHY products. Various
daughter cards can connect via an RGMII connector or an RMII connector.
The EDS board is not intended for stand-alone use and has no ethernet
capabilities when no daughter board is connected. As such, this device
tree is intended to be used with a DT overlay defining the add-on board.
To better ensure consistency, some items are defined here as a form of
documentation so that all add-on overlays will use the same terms.
Disable AES node on lan966x pcb8290, pcb891 and pcb8309 because these
boards have lan966x that uses secure OS which reserves the AES block.
Therefore it can't be exposed to non-secure world.
Merge tag 'stm32-dt-for-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v6.1, round 1
Highlights:
----------
- MPU:
- General:
- Add I2C support (5 instances) on STM32MP13.
- Add SPI support (5 instabces) on STM32MP13.
- Add timer interrupts support on STM32MP15.
- ST boards:
- Enable I2C1 and I2C5 on stm32mp135f-dk board.
- Add SPI5 on stm32mp135f-dk board but disabled as only available on
the GPIO expansion connector.
- ARGON:
- Remove spidev node as not used by the code.
* tag 'stm32-dt-for-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: argon: remove spidev node
ARM: dts: stm32: Create separate pinmux for qspi cs pin in stm32mp15-pinctrl.dtsi
ARM: dts: stm32: Fix typo in license text for Engicam boards
ARM: dts: stm32: Add timer interrupts on stm32mp15
ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk
ARM: dts: stm32: add spi nodes into stm32mp131.dtsi
ARM: dts: stm32: enable i2c1 and i2c5 on stm32mp135f-dk.dts
ARM: dts: stm32: add i2c nodes into stm32mp131.dtsi
Merge tag 'v6.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New boards the Anberic RG353P and RG503, Radxa Rock4c+ (variant with
different display outputs), Pine64 Pinephone Pro, Open AI Lab EAIDK-610.
New components of the rk356x (Video encoder/decoder, pcie, CSI dphy).
New board-peripherals for rock3a (pcie, i2c, regulators, rtc), quartz64-b
(pcie, analog audio) and BPI-R2-Pro (pcie), ROCK Pi (leds), Odroid Go (charger)
Usage of the new-ish bclk special handling for audio on rk3399.
* tag 'v6.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
arm64: dts: rockchip: use BCLK to GPIO switch on rk3399
arm64: dts: rockchip: Add Hantro encoder node to rk356x
arm64: dts: rockchip: Add VPU support for RK3568/RK3566
arm64: dts: rockchip: Enable PCIe controller on rock3a
arm64: dts: rockchip: add rtc to rock3a
arm64: dts: rockchip: Add PCIe 2 nodes to quartz64-b
arm64: dts: rockchip: add Anbernic RG353P and RG503
dt-bindings: arm: rockchip: Add Anbernic RG353P and RG503
dt-bindings: vendor-prefixes: add Anbernic
arm64: dts: rockchip: Add regulator suffix to BPI-R2-Pro
arm64: dts: rockchip: add LEDs for ROCK 4C+
arm64: dts: rockchip: add LED for ROCK Pi 4A/B/C/A+/B+
arm64: dts: rockchip: add rk817 chg to Odroid Go Advance
arm64: dts: rockchip: Fix SD card controller probe on Pinephone Pro
arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
arm64: dts: rockchip: Add RK3399-T OPP table
dt-bindings: arm: rockchip: Document Radxa ROCK 4C+
arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
dt-bindings: arm: rockchip: Add PinePhone Pro bindings
arm64: dts: rockchip: Add dts for a rk3399 based board EAIDK-610
...
Wolfram Sang [Wed, 24 Aug 2022 08:21:28 +0000 (10:21 +0200)]
ARM: dts: stm32: argon: remove spidev node
Commit 956b200a846e ("spi: spidev: Warn loudly if instantiated from DT
as "spidev"") states that there should not be spidev nodes in DTs.
Remove this non-HW description. There won't be a regression because it
won't bind since 2015 anyhow.
Fixes: 16e3e44c5b87 ("ARM: dts: stm32: Add support for the emtrion emSBC-Argon") Cc: Reinhold Mueller <reinhold.mueller@emtrion.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Patrice Chotard [Tue, 23 Aug 2022 07:58:49 +0000 (09:58 +0200)]
ARM: dts: stm32: Create separate pinmux for qspi cs pin in stm32mp15-pinctrl.dtsi
Create a separate pinmux for qspi chip select in stm32mp15-pinctrl.dtsi.
In the case we want to use transfer_one() API to communicate with a SPI
device, chip select signal must be driven individually.
Uwe Kleine-König [Thu, 19 May 2022 16:28:38 +0000 (18:28 +0200)]
ARM: dts: stm32: Add timer interrupts on stm32mp15
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk
Add pinctrl information and a disabled spi5 node within
stm32mp135f-dk.dts in order to use the spi5 bus which is
available via the GPIO expansion pins of the STM32MP135 Discovery board.
arm64: dts: rockchip: use BCLK to GPIO switch on rk3399
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.
In order to:
1. prevent BCLK from turning on by other component.
2. keep BCLK and LRCLK being present at the same time
This patch adjusts the device tree to allow BCLK to switch
to GPIO func before LRCLK output, and switch back during
LRCLK is output.
Nicolas Frattaroli [Sun, 12 Jun 2022 15:53:46 +0000 (17:53 +0200)]
arm64: dts: rockchip: Add Hantro encoder node to rk356x
The RK3566 and RK3568 come with a dedicated Hantro instance solely for
encoding. This patch adds a node for this to the device tree, along with
a node for its MMU.
The Linux kernel has no logic to decide which driver to probe first.
To prevent race conditions remove the rk3036 emac node
fall back compatible string.
Chris Morgan [Tue, 6 Sep 2022 21:03:24 +0000 (16:03 -0500)]
arm64: dts: rockchip: add Anbernic RG353P and RG503
Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices
from Anbernic.
Both devices have:
- 2 SDMMC slots.
- A Realtek rtl8821cs WiFi/Bluetooth adapter.
- A mini HDMI port.
- A USB C host port and a USB C otg port (currently only working as
device).
- Multiple GPIO buttons and a single ADC button.
- Dual analog joysticks controlled via a GPIO mux.
- A headphone jack with amplified stereo speakers via a SGM4865 amp.
- A PWM based vibrator for force feedback.
The RG353P has:
- 2GB LPDDR4 RAM.
- A 32GB eMMC.
- A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
controlled touchscreen (touchscreen is a Hynitron CST340).
The RG503 has:
- 1GB LPDDR4 RAM.
- A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
with part number ams495qa04. Data for this panel is provided via the
DSI interface, however commands are sent via a 9-bit 3-wire SPI
interface. The MISO pin of SPI3 of the SOC is wired to the input of
the panel, so it must be bitbanged.
This devicetree enables the following hardware:
- HDMI (plus audio).
- Analog audio, including speakers.
- All buttons.
- All SDMMC/eMMC/SDIO controllers.
- The ADC joysticks (note a pending patch is required to use them).
- WiFi/Bluetooth (note out of tree drivers are required).
- The PWM based vibrator motor.
The following hardware is not enabled:
- The display panels (drivers are being written and there are issues
with the upstream DSI and VOP2 subsystems).
- Battery (driver pending).
- Touchscreen on the RG353P (note the i2c2 bus is enabled for it).
Chris Morgan [Sat, 27 Aug 2022 02:16:23 +0000 (21:16 -0500)]
arm64: dts: rockchip: add rk817 chg to Odroid Go Advance
Add the new rk817 charger driver to the Odroid Go Advance. Create a
monitored battery node as well for the charger to use. All values
from monitored battery are gathered from the BSP kernel for the
Odroid Go Advance provided by HardKernel.
Ondrej Jirman [Sun, 4 Sep 2022 23:36:47 +0000 (01:36 +0200)]
arm64: dts: rockchip: Fix SD card controller probe on Pinephone Pro
Voltage constraints on vccio_sd are invalid. They don't match the voltages
that LDO9 can generate, and this causes rk808-regulator driver to fail
to probe with -EINVAL when it tries to apply the constraints during boot.
Fix the constraints to something that LDO9 can be actually configured for.
Fixes: 78a21c7d5952 ("arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro") Signed-off-by: Ondrej Jirman <megi@xff.cz> Reviewed-by: Caleb Connolly <kc@postmarketos.org> Reviewed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Tested-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Link: https://lore.kernel.org/r/20220904233652.3197885-1-megi@xff.cz Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jagan Teki [Fri, 2 Sep 2022 06:50:57 +0000 (12:20 +0530)]
arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
Add support for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Jagan Teki [Fri, 2 Sep 2022 06:50:55 +0000 (12:20 +0530)]
dt-bindings: arm: rockchip: Document Radxa ROCK 4C+
Document the dt-bindings for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Martijn Braam <martijn@brixit.nl> Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted] Co-developed-by: Ondrej Jirman <megi@xff.cz> Signed-off-by: Ondrej Jirman <megi@xff.cz> Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk> Reviewed-by: Caleb Connolly <kc@postmarketos.org> Reviewed-by: NÃcolas F. R. A. Prado <n@nfraprado.net> Tested-by: NÃcolas F. R. A. Prado <n@nfraprado.net> Link: https://lore.kernel.org/r/20220829050040.17330-2-tom@tom-fitzhenry.me.uk Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Merge tag 'renesas-dt-bindings-for-v6.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v6.1
- Document support for the R-Car H3Ne-1.7G SoC on the Salvator-XS and
ULCB development boards,
- Document system controller support for the RZ/Five SoC,
- Document support for the R-Car V3H2 SoC and the Condor-I development
board.
* tag 'renesas-dt-bindings-for-v6.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Document Renesas R-Car V3H2 SoC and board
dt-bindings: soc: renesas: renesas,rzg2l-sysc: Document RZ/Five SoC
dt-bindings: arm: renesas: Document R-Car H3Ne-1.7G SoC and boards
Merge tag 'renesas-arm-dt-for-v6.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v6.1
- SDHI and eMMC support for the R-Car S4-8 SoC and the Spider
development board,
- Timer (CMT and TMU) and SPI (MSIOF) support for the R-Car S4-8 SoC,
- External and GPIO interrupt support for the RZ/G2L and RZ/V2L SoCs,
- Initial support for the R-Car H3Ne-1.7G (R8A779MB) SoC,
- SPI DMA support for the RZ/G2UL, RZ/G2L, and RZ/V2L SoCs,
- Pin control and I2C support for the RZ/V2M SoC and the RZ/V2M
Evaluation Kit,
- initial support for the R-Car V3H2 (R8A77980A) SoC and the Condor-I
development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v6.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (33 commits)
arm64: dts: renesas: Add V3H2 Condor-I board support
arm64: dts: renesas: Add r8a77980a.dtsi
arm64: dts: renesas: Add condor-common.dtsi
arm64: dts: renesas: Drop clock-names property from RPC node
arm64: dts: renesas: r8a779f0: Add MSIOF nodes
arm64: dts: renesas: r8a774a1: Put I2C aliases to board files
arm64: dts: renesas: r8a774e1: Rename i2c_dvfs to iic_pmic
arm64: dts: renesas: r8a779a0: Put I2C aliases to board files
arm64: dts: renesas: r8a77990: Put I2C aliases to board files
arm64: dts: renesas: r8a77980: Put I2C aliases to board files
arm64: dts: renesas: r8a77970: Put I2C aliases to board files
arm64: dts: renesas: r8a779{51|60|65}: Put I2C aliases to board files
arm64: dts: renesas: rzv2m evk: Enable i2c
arm64: dts: renesas: r9a09g011: Add i2c nodes
arm64: dts: renesas: r9a09g011: Add pinctrl node
arm64: dts: renesas: r9a07g043: Fix SCI{Rx,Tx} interrupt types
arm64: dts: renesas: r9a07g054: Fix SCI{Rx,Tx} interrupt types
arm64: dts: renesas: r9a07g044: Fix SCI{Rx,Tx} interrupt types
arm64: dts: renesas: r9a07g043: Fix audio clk node names
arm64: dts: renesas: r9a07g054: Add DMA support to RSPI
...
Merge tag 'at91-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT for v6.1
It contains:
- one new LAN966X based board, namely lan966x-pcb8290
- gpio leds support for lan966x-pcb8291 and lan966x-pcb8309
- a cleanup for sam9x60ek to avoid DT compilation warning due to regulators
* tag 'at91-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: lan966x: add led configuration
ARM: dts: at91: sam9x60ek: remove simple-bus for regulators
ARM: dts: lan966x: add support for pcb8290
Lad Prabhakar [Mon, 29 Aug 2022 21:51:28 +0000 (22:51 +0100)]
arm64: dts: renesas: Drop clock-names property from RPC node
With 'unevaluatedProperties' support implemented, there are a number of
warnings when running dtbs_check:
arch/arm64/boot/dts/renesas/r8a774b1-hihope-rzg2n-rev2-ex-idk-1110wr.dtb: spi@ee200000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml
The main problem is that the DT bindings do not allow clock-names.
So just drop the clock-names properties from the SoC DTSI files.
Claudiu Beznea [Fri, 26 Aug 2022 08:39:27 +0000 (11:39 +0300)]
ARM: dts: at91: sam9x60ek: remove simple-bus for regulators
Keep regulators as individual devices. There is no need to have them
under simple bus. This will throw compilation warnings like:
- unnecessary #address-cells/#size-cells without "ranges" or child "reg"
property.
- node has a unit name, but no reg or ranges property.
While at it move it down a bit in the file to keep entries sorted
alphabetically.
Michael Riesch [Tue, 12 Jul 2022 13:32:04 +0000 (15:32 +0200)]
arm64: dts: rockchip: specify pinctrl for i2c adapters on rock-3a
On the Radxa ROCK3 Model A the I2C adapters related to the MIPI DSI
connector and the M.2/NGFF connector use the non-default pins.
Specify the correct pinctrl but leave the adapters disabled (as
they are supposed to be activated by overlays that describe the
external hardware).
Michael Riesch [Tue, 12 Jul 2022 13:32:03 +0000 (15:32 +0200)]
arm64: dts: rockchip: add vcc_mipi regulator to rock-3a
The Radxa ROCK3 Model A features a voltage regulator that provides
a 3V3 supply to the MIPI DSI connector. Add this regulator to the
device tree of the board.
Michael Riesch [Tue, 12 Jul 2022 13:32:02 +0000 (15:32 +0200)]
arm64: dts: rockchip: add vcc_cam regulator to rock-3a
The Radxa ROCK3 Model A features a voltage regulator that provides
a 3V3 supply to the MIPI CSI connector. Add this regulator to the
device tree of the board.
Arnd Bergmann [Mon, 29 Aug 2022 09:13:46 +0000 (11:13 +0200)]
Merge tag 'gemini-dts-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Gemini DTS updates for kernel v6.1:
- Enable Gigabit ethernet on SSI1328 and NS2502
- Modify NS2502 us use RedBoot partition parsing
* tag 'gemini-dts-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Let Gemini NS2502 parse redboot partitions
ARM: dts: gemini: ssi1328: permit to use gigabit
ARM: dts: gemini: ns2502: permit to use gigabit
Geert Uytterhoeven [Fri, 26 Aug 2022 14:49:48 +0000 (16:49 +0200)]
arm64: dts: renesas: r8a774e1: Rename i2c_dvfs to iic_pmic
As RZ/G2 SoCs do not support DVFS, the "iic-dvfs" module was renamed to
"iic-pmic" in the RZ/G Series, 2nd Generation User’s Manual: Hardware
Rev. 1.00.
See also commit a636d8037ef6028a ("arm64: dts: renesas: rzg2: Rename
i2c_dvfs to iic_pmic"), which apparently forgot to update RZ/G2H.
Linus Torvalds [Sun, 28 Aug 2022 21:49:59 +0000 (14:49 -0700)]
Merge tag 'mm-hotfixes-stable-2022-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more hotfixes from Andrew Morton:
"Seventeen hotfixes. Mostly memory management things.
Ten patches are cc:stable, addressing pre-6.0 issues"
* tag 'mm-hotfixes-stable-2022-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
.mailmap: update Luca Ceresoli's e-mail address
mm/mprotect: only reference swap pfn page if type match
squashfs: don't call kmalloc in decompressors
mm/damon/dbgfs: avoid duplicate context directory creation
mailmap: update email address for Colin King
asm-generic: sections: refactor memory_intersects
bootmem: remove the vmemmap pages from kmemleak in put_page_bootmem
ocfs2: fix freeing uninitialized resource on ocfs2_dlm_shutdown
Revert "memcg: cleanup racy sum avoidance code"
mm/zsmalloc: do not attempt to free IS_ERR handle
binder_alloc: add missing mmap_lock calls when using the VMA
mm: re-allow pinning of zero pfns (again)
vmcoreinfo: add kallsyms_num_syms symbol
mailmap: update Guilherme G. Piccoli's email addresses
writeback: avoid use-after-free after removing device
shmem: update folio if shmem_replace_page() updates the page
mm/hugetlb: avoid corrupting page->mapping in hugetlb_mcopy_atomic_pte
Linus Torvalds [Sun, 28 Aug 2022 21:36:27 +0000 (14:36 -0700)]
Merge tag 'bitmap-6.0-rc3' of github.com:/norov/linux
Pull bitmap fixes from Yury Norov:
"Fix the reported issues, and implements the suggested improvements,
for the version of the cpumask tests [1] that was merged with commit c41e8866c28c ("lib/test: introduce cpumask KUnit test suite").
These changes include fixes for the tests, and better alignment with
the KUnit style guidelines"
* tag 'bitmap-6.0-rc3' of github.com:/norov/linux:
lib/cpumask_kunit: add tests file to MAINTAINERS
lib/cpumask_kunit: log mask contents
lib/test_cpumask: follow KUnit style guidelines
lib/test_cpumask: fix cpu_possible_mask last test
lib/test_cpumask: drop cpu_possible_mask full test
projects / users / jedix / linux-maple.git / log