Xiang Liu [Fri, 21 Mar 2025 12:47:23 +0000 (20:47 +0800)]
drm/amdgpu: Use correct gfx deferred error count
In the case of parsing GFX deferred error from SMU corrected error
channel, the error count should be set to 1 instead of parsing from
MISC0 register, which is 0.
Signed-off-by: Xiang Liu <xiang.liu@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Li [Tue, 11 Mar 2025 13:43:38 +0000 (09:43 -0400)]
drm/amd/display: Actually do immediate vblank disable
[Why]
The `vblank_config.offdelay` field follows the same semantics as the
`drm_vblank_offdelay` parameter. Setting it to 0 will never disable
vblank.
[How]
Set `offdelay` to a positive number.
Fixes: e45b6716de4b ("drm/amd/display: use a more lax vblank enable policy for DCN35+") Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Brendan Tam [Fri, 14 Mar 2025 17:09:13 +0000 (13:09 -0400)]
drm/amd/display: prevent hang on link training fail
[Why]
When link training fails, the phy clock will be disabled. However, in
enable_streams, it is assumed that link training succeeded and the
mux selects the phy clock, causing a hang when a register write is made.
[How]
When enable_stream is hit, check if link training failed. If it did, fall
back to the ref clock to avoid a hang and keep the system in a recoverable
state.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Brendan Tam <Brendan.Tam@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Leo Li [Mon, 10 Mar 2025 16:20:39 +0000 (12:20 -0400)]
drm/amd/display: Increase vblank offdelay for PSR panels
[Why]
Depending on when the HW latching event (vupdate) of double-buffered
registers happen relative to the PSR SDP (signals panel psr enter/exit)
deadline, and how bad the Panel clock has drifted since the last ALPM
off event, there can be up to 3 frames of delay between sending the PSR
exit cmd to DMUB fw, and when the panel starts displaying live frames.
This can manifest as micro-stuttering when userspace commit patterns
cause rapid toggling of the DRM vblank counter, since PSR enter/exit is
hooked up to DRM vblank disable/enable respectively.
In the ideal world, the panel should present the live frame immediately
on PSR exit cmd. But due to HW design and PSR limitations, immediate
exit can only happen by chance, when:
1. PSR exit cmd is ack'd by FW before HW latching (vupdate) event, and
2. Panel's SDP deadline -- determined by it's PSR Start Delay in DPCD
71h -- is after the vupdate event. The PSR exit SDP can then be sent
immediately after HW latches. Otherwise, we have to wait 1 frame. And
3. There is negligible drift between the panel's clock and source clock.
Otherwise, there can be up to 1 frame of drift.
Note that this delay is not expected with Panel Replay.
[How]
Since PSR power savings can be quite substantial, and there are a lot of
systems in the wild with PSR panels, It'll be nice to have a middle
ground that balances user experience with power savings.
A simple way to achieve this is by extending the vblank offdelay, such
that additional PSR exit delays will be less perceivable.
This ensures that `3_frames_ms` will only be experienced as a 20% delay
on top how long the panel has been static, and thus make the delay
less perceivable.
If this ends up being too high of a percentage, it can be dropped
further in a future change.
Fixes: 537ef0f88897 ("drm/amd/display: use new vblank enable policy for DCN35+") Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Denis Arefev [Fri, 21 Mar 2025 10:52:32 +0000 (13:52 +0300)]
drm/amd/pm: Prevent division by zero
The user can set any speed value.
If speed is greater than UINT_MAX/8, division by zero is possible.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b64625a303de ("drm/amd/pm: correct the address of Arcturus fan related registers") Signed-off-by: Denis Arefev <arefev@swemel.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Asad Kamal [Mon, 17 Mar 2025 12:07:06 +0000 (20:07 +0800)]
drm/amd/pm: Update feature list for smu_v13_0_6
Update feature list for smu_v13_0_6 to show vcn & smu deep
sleep feature enable status
Signed-off-by: Asad Kamal <asad.kamal@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Srinivasan Shanmugam [Fri, 21 Mar 2025 01:23:47 +0000 (06:53 +0530)]
drm/amdgpu: Add parameter documentation for amdgpu_sync_fence
The 'flags' parameter, which specifies memory allocation behavior while
creating a sync entry,
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/amdgpu_sync.c:162: warning: Function parameter or struct member 'flags' not described in 'amdgpu_sync_fence'
Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 11 Mar 2025 22:00:57 +0000 (18:00 -0400)]
drm/amdgpu/discovery: optionally use fw based ip discovery
On chips without native IP discovery support, use the fw binary
if available, otherwise we can continue without it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Flora Cui <flora.cui@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Flora Cui <flora.cui@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Flora Cui [Thu, 27 Feb 2025 02:39:27 +0000 (10:39 +0800)]
drm/amdgpu/discovery: check ip_discovery fw file available
Signed-off-by: Flora Cui <flora.cui@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jesse.zhang@amd.com [Thu, 27 Feb 2025 11:33:19 +0000 (19:33 +0800)]
drm/amdgpu/sdma_v4_4_2: update VM flush implementation for SDMA
This commit updates the VM flush implementation for the SDMA engine.
- Added a new function `sdma_v4_4_2_get_invalidate_req` to construct the VM_INVALIDATE_ENG0_REQ
register value for the specified VMID and flush type. This function ensures that all relevant
page table cache levels (L1 PTEs, L2 PTEs, and L2 PDEs) are invalidated.
- Modified the `sdma_v4_4_2_ring_emit_vm_flush` function to use the new `sdma_v4_4_2_get_invalidate_req`
function. The updated function emits the necessary register writes and waits to perform a VM flush
for the specified VMID. It updates the PTB address registers and issues a VM invalidation request
using the specified VM invalidation engine.
- Included the necessary header file `gc/gc_9_0_sh_mask.h` to provide access to the required register
definitions.
v2: vm flush by the vm inalidation packet (Lijo)
v3: code stle and define thh macro for the vm invalidation packet (Christian)
v4: Format definition sdma vm invalidate packet (Lijo)
Jesse.zhang@amd.com [Tue, 25 Feb 2025 07:25:00 +0000 (15:25 +0800)]
drm/amdgpu: Optimize VM invalidation engine allocation and synchronize GPU TLB flush
- Modify the VM invalidation engine allocation logic to handle SDMA page rings.
SDMA page rings now share the VM invalidation engine with SDMA gfx rings instead of
allocating a separate engine. This change ensures efficient resource management and
avoids the issue of insufficient VM invalidation engines.
- Add synchronization for GPU TLB flush operations in gmc_v9_0.c.
Use spin_lock and spin_unlock to ensure thread safety and prevent race conditions
during TLB flush operations. This improves the stability and reliability of the driver,
especially in multi-threaded environments.
v2: replace the sdma ring check with a function `amdgpu_sdma_is_page_queue`
to check if a ring is an SDMA page queue.(Lijo)
v3: Add GC version check, only enabled on GC9.4.3/9.4.4/9.5.0
v4: Fix code style and add more detailed description (Christian)
v5: Remove dependency on vm_inv_eng loop order, explicitly lookup shared inv_eng(Christian/Lijo)
v6: Added search shared ring function amdgpu_sdma_get_shared_ring (Lijo)
Jesse.zhang@amd.com [Fri, 28 Feb 2025 08:18:32 +0000 (16:18 +0800)]
drm/amd/amdgpu: Increase max rings to enable SDMA page ring
Increase the maximum number of rings supported by the AMDGPU driver from 133 to 149.
This change is necessary to enable support for the SDMA page ring.
Xiang Liu [Wed, 19 Mar 2025 09:02:49 +0000 (17:02 +0800)]
drm/amdgpu: Decode deferred error type in gfx aca bank parser
In the case of injecting uncorrected error with background workload,
the deferred error among uncorrected errors need to be specified
by checking the deferred and poison bits of status register.
v2: refine checking for deferred error
v2: log possiable DEs among CEs
v2: generate CPER records for DEs among UEs
Signed-off-by: Xiang Liu <xiang.liu@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Srinivasan Shanmugam [Thu, 20 Mar 2025 16:01:35 +0000 (21:31 +0530)]
drm/amdgpu/gfx11: Add Cleaner Shader Support for GFX11.5 GPUs
Enable the cleaner shader for GFX11.5.0/11.5.1 GPUs to provide data
isolation between GPU workloads. The cleaner shader is responsible for
clearing the Local Data Store (LDS), Vector General Purpose Registers
(VGPRs), and Scalar General Purpose Registers (SGPRs), which helps
prevent data leakage and ensures accurate computation results.
This update extends cleaner shader support to GFX11.5.0/11.5.1 GPUs,
previously available for GFX11.0.3. It enhances security by clearing GPU
memory between processes and maintains a consistent GPU state across KGD
and KFD workloads.
Cc: Mario Sopena-Novales <mario.novales@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 14 Mar 2025 23:23:46 +0000 (19:23 -0400)]
drm/amdgpu/sdma: fix engine reset handling
Move the kfd suspend/resume code into the caller. That
is where the KFD is likely to detect a reset so on the KFD
side there is no need to call them. Also add a mutex to
lock the actual reset sequence.
v2: make the locking per instance
Fixes: bac38ca8c475 ("drm/amdkfd: implement per queue sdma reset for gfx 9.4+") Reviewed-by: Jesse Zhang <jesse.zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 18 Mar 2025 14:43:41 +0000 (15:43 +0100)]
drm/amdgpu: remove invalid usage of sched.ready
I can't count how often I had to remove this nonsense.
Probably doesn't need an explanation any more.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 6 Feb 2025 13:26:30 +0000 (14:26 +0100)]
drm/amdgpu: add cleaner shader trace point
Note when the cleaner shader is executed.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 6 Feb 2025 13:16:06 +0000 (14:16 +0100)]
drm/amdgpu: add isolation trace point
Note when we switch from one isolation owner to another.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 27 Jan 2025 15:27:51 +0000 (16:27 +0100)]
drm/amdgpu: stop reserving VMIDs to enforce isolation
That was quite troublesome for gang submit. Completely drop this
approach and enforce the isolation separately.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 15 Jan 2025 12:44:26 +0000 (13:44 +0100)]
drm/amdgpu: rework how isolation is enforced v2
Limiting the number of available VMIDs to enforce isolation causes some
issues with gang submit and applying certain HW workarounds which
require multiple VMIDs to work correctly.
So instead start to track all submissions to the relevant engines in a
per partition data structure and use the dma_fences of the submissions
to enforce isolation similar to what a VMID limit does.
v2: use ~0l for jobs without isolation to distinct it from kernel
submissions which uses NULL for the owner. Add some warning when we
are OOM.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 23 Jan 2025 13:59:01 +0000 (14:59 +0100)]
drm/amdgpu: overwrite signaled fence in amdgpu_sync
This allows using amdgpu_sync even without peeking into the fences for a
long time.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 15 Jan 2025 14:10:13 +0000 (15:10 +0100)]
drm/amdgpu: use GFP_NOWAIT for memory allocations
In the critical submission path memory allocations can't wait for
reclaim since that can potentially wait for submissions to finish.
Finally clean that up and mark most memory allocations in the critical
path with GFP_NOWAIT. The only exception left is the dma_fence_array()
used when no VMID is available, but that will be cleaned up later on.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reason for revert: this causes some tests fail with call trace.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Acked-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jonathan Kim [Fri, 14 Mar 2025 15:08:21 +0000 (11:08 -0400)]
drm/amdkfd: set precise mem ops caps to disabled for gfx 11 and 12
Clause instructions with precise memory enabled currently hang the
shader so set capabilities flag to disabled since it's unsafe to use
for debugging.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com> Tested-by: Lancelot Six <lancelot.six@amd.com> Reviewed-by: Harish Kasiviswanathan <harish.kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lijo Lazar [Fri, 7 Mar 2025 05:41:23 +0000 (11:11 +0530)]
drm/amd/pm: Add debug bit for smu pool allocation
In certain cases, it's desirable to avoid PMFW log transactions to
system memory. Add a mask bit to decide whether to allocate smu pool in
device memory or system memory.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 14 Mar 2025 13:45:51 +0000 (09:45 -0400)]
drm/amdgpu/vcn: adjust workload profile handling
No need to make the workload profile setup dependent
on the results of cancelling the delayed work thread.
We have all of the necessary checking in place for the
workload profile reference counting, so separate the
two. As it is now, we can theoretically end up with
the call from begin_use happening while the worker
thread is executing which would result in the profile
not getting set for that submission. It should not
affect the reference counting.
v2: bail early if the the profile is already active (Lijo)
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 14 Mar 2025 13:29:59 +0000 (09:29 -0400)]
drm/amdgpu/gfx: adjust workload profile handling
No need to make the workload profile setup dependent
on the results of cancelling the delayed work thread.
We have all of the necessary checking in place for the
workload profile reference counting, so separate the
two. As it is now, we can theoretically end up with
the call from begin_use happening while the worker
thread is executing which would result in the profile
not getting set for that submission. It should not
affect the reference counting.
v2: bail early if the the profile is already active (Lijo)
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 12 Mar 2025 13:48:47 +0000 (09:48 -0400)]
drm/amdgpu/vcn: fix ref counting for ring based profile handling
We need to make sure the workload profile ref counts are
balanced. This isn't currently the case because we can
increment the count on submissions, but the decrement may
be delayed as work comes in. Track when we enable the
workload profile so the references are balanced.
v2: switch to a mutex and active flag
v3: fix mutex init
Fixes: 1443dd3c67f6 ("drm/amd/pm: fix and simplify workload handling") Cc: Yang Wang <kevinyang.wang@amd.com> Cc: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 12 Mar 2025 13:44:19 +0000 (09:44 -0400)]
drm/amdgpu/gfx: fix ref counting for ring based profile handling
We need to make sure the workload profile ref counts are
balanced. This isn't currently the case because we can
increment the count on submissions, but the decrement may
be delayed as work comes in. Track when we enable the
workload profile so the references are balanced.
v2: switch to a mutex and active flag
v3: fix mutex init
Fixes: 8fdb3958e396 ("drm/amdgpu/gfx: add ring helpers for setting workload profile") Cc: Yang Wang <kevinyang.wang@amd.com> Cc: Kenneth Feng <kenneth.feng@amd.com> Tested-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Harish Kasiviswanathan [Fri, 14 Mar 2025 16:03:53 +0000 (12:03 -0400)]
drm/amdkfd: Fix bug in config_dequeue_wait_counts
For certain ASICs where dequeue_wait_count don't need to be initialized,
pm_config_dequeue_wait_counts_v9 return without filling in the packet
information. However, the calling function interprets this as a success
and sends the uninitialized packet to firmware causing hang.
Fix the above bug by not calling pm_config_dequeue_wait_counts_v9 for
ASICs that don't need the value to be initialized.
v2: Removed redudant code.
Tidy up code based on review comments
v3: Don't call pm_config_dequeue_wait_counts_v9 for certain ASICs
Fixes: ed962f8d0603 ("drm/amdkfd: Add pm_config_dequeue_wait_counts API") Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Reviewed-by: Jonathan Kim <jonathan.kim@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 14 Jan 2025 12:51:39 +0000 (13:51 +0100)]
drm/amdgpu: grab an additional reference on the gang fence v2
We keep the gang submission fence around in adev, make sure that it
stays alive.
v2: fix memory leak on retry
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jesse.zhang@amd.com [Mon, 17 Mar 2025 01:14:36 +0000 (09:14 +0800)]
drm/amdgpu: Fix SDMA engine reset logic
The scheduler should restart only if the reset operation
succeeds This ensures that new tasks are only submitted
to the queues after a successful reset.
Fixes: 4c02f7301657 ("drm/amdgpu: Introduce conditional user queue suspension for SDMA resets") Suggested-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jesse.Zhang <Jesse.zhang@amd.com> Reviewed-by: Tim Huang <tim.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tomasz Pakuła [Tue, 11 Mar 2025 21:38:33 +0000 (22:38 +0100)]
drm/amdgpu/pm: Handle SCLK offset correctly in overdrive for smu 14.0.2
Currently, it seems like the code was carried over from RDNA3 because
it assumes two possible values to set. RDNA4, instead of having:
0: min SCLK
1: max SCLK
only has
0: SCLK offset
This change makes it so it only reports current offset value instead of
showing possible min/max values and their indices. Moreover, it now only
accepts the offset as a value, without the indice index.
Additionally, the lower bound was printed as %u by mistake.
Setting this offset:
Old: "s 1 <offset>"
New: "s <offset>"
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4036 Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Taimur Hassan [Sun, 9 Mar 2025 08:57:46 +0000 (04:57 -0400)]
drm/amd/display: 3.2.325
This version brings along following fixes:
- Use DPM table clk setting for dml2 soc dscclk
- Update static soc table
- Fix incorrect fw_state address in dmub_srv
- Use HW lock mgr for PSR1 when only one eDP
- Revert "Support for reg inbox0 for host->DMUB CMDs"
- Change notification of link BW allocation
- Fix message for support_edp0_on_dp1
- Guard against setting dispclk low for dcn31x
- Prevent VStartup Overflow
- Check pipe->stream before passing it to a function
Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Charlene Liu [Fri, 28 Feb 2025 13:02:20 +0000 (08:02 -0500)]
drm/amd/display: Use DPM table clk setting for dml2 soc dscclk
[WHY]
Not like dppclk/dispclk, dml2 will calculate the minimum required clocks.
For dscclk, it is used for pure comparision.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Charlene Liu <Charlene.Liu@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Charlene Liu [Fri, 7 Mar 2025 23:24:56 +0000 (18:24 -0500)]
drm/amd/display: Update static soc table
[WHY]
Update the static soc table dcn3_5_soc.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Charlene Liu <Charlene.Liu@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lo-an Chen [Mon, 10 Mar 2025 06:52:22 +0000 (14:52 +0800)]
drm/amd/display: Fix incorrect fw_state address in dmub_srv
[WHY]
The fw_state in dmub_srv was assigned with wrong address.
The address was pointed to the firmware region.
[HOW]
Fix the firmware state by using DMUB_DEBUG_FW_STATE_OFFSET
in dmub_cmd.h.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Lo-an Chen <lo-an.chen@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Limonciello [Fri, 7 Mar 2025 21:55:20 +0000 (15:55 -0600)]
drm/amd/display: Use HW lock mgr for PSR1 when only one eDP
[WHY]
DMUB locking is important to make sure that registers aren't accessed
while in PSR. Previously it was enabled but caused a deadlock in
situations with multiple eDP panels.
[HOW]
Detect if multiple eDP panels are in use to decide whether to use
lock. Refactor the function so that the first check is for PSR-SU
and then replay is in use to prevent having to look up number
of eDP panels for those configurations.
Fixes: f245b400a223 ("Revert "drm/amd/display: Use HW lock mgr for PSR1"") Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3965 Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cruise Hung [Tue, 25 Feb 2025 15:03:29 +0000 (23:03 +0800)]
drm/amd/display: Change notification of link BW allocation
[WHY & HOW]
The response of DP BW allocation is handled in Outbox ISR.
When it failed to request the DP BW allocation, it sent another
DPCD request in Outbox ISR immediately. The DP AUX reply also
uses the Outbox ISR. So, no AUX reply happened in this case.
Change to use HPD IRQ for the notification.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com> Signed-off-by: Cruise Hung <Cruise.Hung@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jing Zhou [Tue, 4 Mar 2025 15:15:56 +0000 (23:15 +0800)]
drm/amd/display: Guard against setting dispclk low for dcn31x
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Chris Park <chris.park@amd.com> Reviewed-by: Eric Yang <eric.yang@amd.com> Signed-off-by: Jing Zhou <Jing.Zhou@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ryan Seto [Fri, 28 Feb 2025 20:52:42 +0000 (15:52 -0500)]
drm/amd/display: Prevent VStartup Overflow
[WHY & HOW]
Fixed Overflow issue by clamping VStartup to max value of register.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Ryan Seto <ryanseto@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kenneth Feng [Tue, 11 Mar 2025 08:46:39 +0000 (16:46 +0800)]
drm/amd/amdgpu: shorten the gfx idle worker timeout
Shorten the gfx idle worker timeout. This is to sync with
DAL when there is no activity on the screen. Original 1
second can not sync with DAL, so DAL can not apply MALL
when the workload type is not bootup default.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move to probe so we can check the PCI device type and
only apply the drm_firmware_drivers_only() check for
PCI DISPLAY classes. Also add a module parameter to
override the nomodeset kernel parameter as a workaround
for platforms that have this hardcoded on their kernel
command lines.
Reviewed-by: Kent Russell <kent.russell@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 13 Mar 2025 20:57:50 +0000 (16:57 -0400)]
drm/amdgpu: drop drm_firmware_drivers_only()
There are a number of systems and cloud providers out there
that have nomodeset hardcoded in their kernel parameters
to block nouveau for the nvidia driver. This prevents the
amdgpu driver from loading. Unfortunately the end user cannot
easily change this. The preferred way to block modules from
loading is to use modprobe.blacklist=<driver>. That is what
providers should be using to block specific drivers.
Drop the check to allow the driver to load even when nomodeset
is specified on the kernel command line.
Reviewed-by: Kent Russell <kent.russell@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Fri, 14 Mar 2025 04:28:39 +0000 (14:28 +1000)]
Merge tag 'mediatek-drm-next-6.15-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 6.15
1. HDMI fixup and refinement
2. Move to devm_platform_ioremap_resource() usage
3. Add MT8188 dsc compatible
4. Fix config_updating flag never false when no mbox channel
5. dp: drm_err => dev_err in HPD path to avoid NULL ptr
6. Add dpi power-domains example
7. Add MT8365 SoC support
8. Fix error codes in mtk_dsi_host_transfer()
David Belanger [Tue, 2 Jul 2024 21:56:41 +0000 (17:56 -0400)]
drm/amdgpu: Restore uncached behaviour on GFX12
Always use MTYPE_UC if UNCACHED flag is specified.
This makes kernarg region uncached and it restores
usermode cache disable debug flag functionality.
Do not set MTYPE_UC for COHERENT flag, on GFX12 coherence is handled by
shader code.
Signed-off-by: David Belanger <david.belanger@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wentao Liang [Wed, 12 Mar 2025 06:31:06 +0000 (14:31 +0800)]
drm/amdgpu/gfx12: correct cleanup of 'me' field with gfx_v12_0_me_fini()
In gfx_v12_0_cp_gfx_load_me_microcode_rs64(), gfx_v12_0_pfp_fini() is
incorrectly used to free 'me' field of 'gfx', since gfx_v12_0_pfp_fini()
can only release 'pfp' field of 'gfx'. The release function of 'me' field
should be gfx_v12_0_me_fini().
Fixes: 52cb80c12e8a ("drm/amdgpu: Add gfx v12_0 ip block support (v6)") Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes: b5c764d6ed55 ("drm/amd/display: Use HW lock mgr for PSR1") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Cc: Sun peng Li <sunpeng.li@amd.com> Cc: Tom Chung <chiahsuan.chung@amd.com> Cc: Daniel Wheeler <daniel.wheeler@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com> Reviewed-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Amber Lin [Thu, 13 Mar 2025 01:14:43 +0000 (21:14 -0400)]
drm/amdkfd: Correct F8_MODE for gfx950
Correct F8_MODE setting for gfx950 that was removed
Fixes: 61972cd93af7 ("drm/amdkfd: Set per-process flags only once for gfx9/10/11/12") Signed-off-by: Amber Lin <Amber.Lin@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviwanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jay Cornwall [Fri, 7 Feb 2025 21:40:34 +0000 (16:40 -0500)]
drm/amdkfd: Fix instruction hazard in gfx12 trap handler
VALU instructions with SGPR source need wait states to avoid hazard
with SALU using different SGPR.
v2: Eliminate some hazards to reduce code explosion
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com> Reviewed-by: Lancelot Six <lancelot.six@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Hung [Tue, 11 Mar 2025 17:10:17 +0000 (11:10 -0600)]
drm/amd/display: Remove incorrect macro guard
This macro guard "__cplusplus" is unnecessary and should not be there.
Signed-off-by: Alex Hung <alex.hung@amd.com> Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lijo Lazar [Thu, 6 Feb 2025 12:10:42 +0000 (17:40 +0530)]
drm/amdgpu: Calculate IP specific xgmi bandwidth
Use IP version specific xgmi speed/width for bandwidth calculation.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Jonathan Kim <jonathan.kim@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / users / hch / misc.git / log