Andy Yan [Sun, 2 Mar 2025 11:52:25 +0000 (19:52 +0800)]
phy: rockchip: usbdp: Avoid call hpd_event_trigger in dp_phy_init
Function rk_udphy_dp_hpd_event_trigger will set vogrf let it
trigger HPD interrupt to DP by Type-C. This configuration is only
required when the DP work in Alternate Mode, and called by
typec_mux_set. In standard DP mode, such settings will prevent
the DP from receiving HPD interrupts.
Andy Yan [Wed, 12 Mar 2025 08:00:07 +0000 (16:00 +0800)]
phy: rockchip: usbdp: Only verify link rates/lanes/voltage when the corresponding set flags are set
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
Nitin Rawat [Mon, 10 Mar 2025 21:12:30 +0000 (14:12 -0700)]
phy: qcom-qmp-ufs: Add PHY Configuration support for sm8750
Add SM8750 specific register layout and table configs. The serdes
TX RX register offset has changed for SM8750 and hence keep UFS
specific serdes offsets in a dedicated header file.
Stefan Eichenberger [Wed, 5 Mar 2025 14:43:16 +0000 (15:43 +0100)]
phy: freescale: imx8m-pcie: assert phy reset and perst in power off
Ensure the PHY reset and perst is asserted during power-off to
guarantee it is in a reset state upon repeated power-on calls. This
resolves an issue where the PHY may not properly initialize during
subsequent power-on cycles. Power-on will deassert the reset at the
appropriate time after tuning the PHY parameters.
During suspend/resume cycles, we observed that the PHY PLL failed to
lock during resume when the CPU temperature increased from 65C to 75C.
The observed errors were:
phy phy-32f00000.pcie-phy.3: phy poweron failed --> -110
imx6q-pcie 33800000.pcie: waiting for PHY ready timeout!
imx6q-pcie 33800000.pcie: PM: dpm_run_callback(): genpd_resume_noirq+0x0/0x80 returns -110
imx6q-pcie 33800000.pcie: PM: failed to resume noirq: error -110
This resulted in a complete CPU freeze, which is resolved by ensuring
the PHY is in reset during power-on, thus preventing PHY PLL failures.
Cc: stable@vger.kernel.org Fixes: 1aa97b002258 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250305144355.20364-3-eichest@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stefan Eichenberger [Wed, 5 Mar 2025 14:43:15 +0000 (15:43 +0100)]
phy: freescale: imx8m-pcie: cleanup reset logic
Remove the switch statement and base perst release on whether it is
found in the device tree. The probe function fails without the reset
property, making it mandatory. Therefore, always release reset
independent of the variant.
This does not change the behavior of the driver but reduces driver
complexity and allows for easier future modifications.
phy_pm_runtime_allow() and phy_pm_runtime_forbid() were added in 2013
as part of
commit ff764963479a ("drivers: phy: add generic PHY framework")
but have remained unused.
Remove them.
Fix up the (English) docs - I've left the Chinese translation.
The Allwinner A523 SoC contains a USB-2.0 PHY fully compatible to the
one used in the D1/T113s SoCs. This PHY controls the two USB-2.0 ports,
there is a separate and quite different PHY for the USB-3.0 port.
Add the new compatible string, with a fallback to the D1 version.
Nicolas Frattaroli [Thu, 6 Mar 2025 19:29:23 +0000 (20:29 +0100)]
phy: phy-rockchip-samsung-hdptx: Add support for RK3576
Despite the compatible already being listed in the bindings, the PHY
driver never gained explicit support for it. This is especially a
problem because the explicitly listed PHY addresses need to be specified
for each SoC.
To solve this, add the compatible, and a PHY config, with the address
gleaned from rk3576.dtsi.
Krzysztof Kozlowski [Thu, 27 Feb 2025 07:05:18 +0000 (08:05 +0100)]
phy: exynos5-usbdrd: Do not depend on Type-C
Older Exynos designs, like Exynos5422, do not have USB Type-C and the
USB DRD PHY does not really need CONFIG_TYPEC for these devices at all.
Incorrectly added optional dependency on CONFIG_TYPEC caused this driver
to be missing for exynos_defconfig and as result Exynos5422-based boards
like Hardkernel Odroid HC1 failed to probe USB.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org> Closes: https://krzk.eu/#/builders/21/builds/6139 Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Closes: https://lore.kernel.org/all/3c0b77e6-357d-453e-8b63-4757c3231bde@samsung.com/ Fixes: 09dc674295a3 ("phy: exynos5-usbdrd: subscribe to orientation notifier if required") Reviewed-by: André Draszik <andre.draszik@linaro.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20250227070518.5468-1-krzysztof.kozlowski@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
Geert Uytterhoeven [Mon, 20 Jan 2025 14:35:03 +0000 (15:35 +0100)]
phy: PHY_LAN966X_SERDES should depend on SOC_LAN966 || MCHP_LAN966X_PCI
The Microchip LAN966X SerDes PHY is only present on Microchip LAN966x
SoCs. However, when used as a PCI endpoint, all peripherals of the
LAN966x SoC can be accessed by the PCI host. Hence add dependencies on
SOC_LAN966 and MCHP_LAN966X_PCI, to prevent asking the user about this
driver when configuring a kernel without Microchip LAN966x SoC and PCIe
support.
Xu Yang [Wed, 4 Dec 2024 05:09:05 +0000 (13:09 +0800)]
phy: fsl-imx8mq-usb: add tca function driver for imx95
The i.MX95 USB3 phy has a Type-C Assist block (TCA). This block consists
two functional blocks (XBar assist and VBus assist) and one system
access interface using APB.
The primary functionality of XBar assist is:
- switching lane for flip
- moving unused lanes into lower power states.
This info can be get from:
i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
This will add support for TCA block to achieve lane switching and tca
lower power functionality.
Damon Ding [Wed, 5 Feb 2025 10:51:57 +0000 (18:51 +0800)]
phy: phy-rockchip-samsung-hdptx: Add eDP mode support for RK3588
The PHY is based on a Samsung IP block that supports HDMI 2.1, and eDP
1.4b. RK3588 integrates the Analogix eDP 1.3 TX controller IP and the
HDMI/eDP TX Combo PHY to support eDP display.
Add basic support for RBR/HBR/HBR2 link rates, and the voltage swing and
pre-emphasis configurations of each link rate are set according to the
eDP 1.3 requirements.
Damon Ding [Wed, 5 Feb 2025 10:51:54 +0000 (18:51 +0800)]
phy: phy-rockchip-samsung-hdptx: Swap the definitions of LCPLL_REF and ROPLL_REF
According to the datasheet, setting the dig_clk_sel bit of CMN_REG(0097)
to 1'b1 selects LCPLL as the reference clock, while setting it to 1'b0
selects the ROPLL.
Pei Xiao [Sat, 8 Feb 2025 03:44:01 +0000 (11:44 +0800)]
phy: freescale: fsl-samsung-hdmi: Use helper function devm_clk_get_enabled()
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables the clocks for the
whole lifetime of the device. Moreover, it is no longer necessary to
unprepare and disable the clocks explicitly.
Dmitry Baryshkov [Sun, 9 Feb 2025 12:31:45 +0000 (14:31 +0200)]
phy: core: don't require set_mode() callback for phy_get_mode() to work
As reported by Damon Ding, the phy_get_mode() call doesn't work as
expected unless the PHY driver has a .set_mode() call. This prompts PHY
drivers to have empty stubs for .set_mode() for the sake of being able
to get the mode.
Make .set_mode() callback truly optional and update PHY's mode even if
it there is none.
Krzysztof Kozlowski [Sat, 11 Jan 2025 18:54:07 +0000 (19:54 +0100)]
phy: stih407-usb: Use syscon_regmap_lookup_by_phandle_args
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
André Draszik [Fri, 6 Dec 2024 16:31:07 +0000 (16:31 +0000)]
phy: exynos5-usbdrd: allow DWC3 runtime suspend with UDC bound (E850+)
To make USB runtime suspend work when a UDC has been bound, the phy
needs to inform the USBDRD controller (DWC3) that Vbus and bvalid are
gone, so that it can in turn raise the respective gadget interrupt with
event == DWC3_DEVICE_EVENT_DISCONNECT, which will cause the USB stack
to clean up, allowing DWC3 to enter runtime suspend.
On e850 and gs101 this isn't working, as the respective signals are not
directly connected, and instead this driver uses override bits in the
PHY IP to set those signals. It currently forcefully sets them to 'on',
so the above mentioned interrupt will not be raised, preventing runtime
suspend.
To detect that state, update this driver to act on the TCPC's
orientation signal - when orientation == NONE, Vbus is gone and we can
clear the respective bits. Similarly, for other orientation values we
re-enable them.
This makes runtime suspend work on platforms with a TCPC (like Pixel6),
while keeping compatibility with platforms without (e850-96).
With runtime suspend working, USB-C cable orientation detection now
also fully works on such platforms, and the link comes up as Superspeed
as expected irrespective of the cable orientation and whether UDC /
gadget are configured and active.
André Draszik [Fri, 6 Dec 2024 16:31:06 +0000 (16:31 +0000)]
phy: exynos5-usbdrd: subscribe to orientation notifier if required
gs101's SS phy needs to be configured differently based on the
connector orientation, as the SS link can only be established if the
mux is configured correctly.
The code to handle programming of the mux is in place already, this commit
now adds the missing pieces to subscribe to the Type-C orientation
switch event.
Note that for this all to work we rely on the USB controller
re-initialising us. It should invoke our .exit() upon cable unplug, and
during cable plug we'll receive the orientation event after which we
expect our .init() to be called.
Above reinitialisation happens if the DWC3 controller can enter runtime
suspend automatically. For the DWC3 driver, this is an opt-in:
echo auto > /sys/devices/.../11110000.usb/power/control
Once done, things work as long as the UDC is not bound as otherwise it
stays busy because it doesn't cancel / stop outstanding TRBs. For now
we have to manually unbind the UDC in that case:
echo "" > sys/kernel/config/usb_gadget/.../UDC
Note that if the orientation-switch property is missing from the DT,
the code will behave as before this commit (meaning for gs101 it will
work in SS mode in one orientation only). Other platforms are not
affected either way.
André Draszik [Fri, 6 Dec 2024 16:31:05 +0000 (16:31 +0000)]
phy: exynos5-usbdrd: gs101: configure SS lanes based on orientation
USB SS lanes need to be configured based on the connector orientation -
at most two lanes will be in use for USB (and the remaining two for
alternate modes like DP).
For the USB link to come up in SS, the lane configuration registers
have to be programmed accordingly.
While we still need a way to be notified of the actual connector
orientation and then reprogram the registers accordingly (at the moment
the configuration happens just once during phy_init() and never again),
we can prepare the code doing the configuration to take the orientation
into account.
Do so.
Note: the mutex is needed to synchronize this with the upcoming
connector orientation callback.
André Draszik [Fri, 6 Dec 2024 16:31:04 +0000 (16:31 +0000)]
phy: exynos5-usbdrd: fix EDS distribution tuning (gs101)
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
orientation-switch is the standard declaration to inform the Type-C mux
layer that a remote-endpoint is capable of processing orientation
change messages.
The USB PHY on gs101 needs to be configured based on the orientation of
the connector. For that the DTS needs a link between the phy's port and
a TCPCi, and we'll need to inform the phy driver that it should handle
the orientation (register a handler).
Update the schema to enforce that by requiring the orientation-switch
and port properties on gs101 (only). We disallow orientation-switch on
all other supported platforms, since other versions of this phy (or its
system integration) don't currently support or even need it.
Even though this new required gs101 property is an ABI break, the
intention for the driver is to behave as before if it's missing
(meaning for gs101 it will work in SS mode in one orientation only).
Other platforms are not affected.
André Draszik [Fri, 6 Dec 2024 16:31:01 +0000 (16:31 +0000)]
dt-bindings: phy: samsung,usb3-drd-phy: add blank lines between DT properties
In [1], Rob pointed out that we should really be separating properties
with blank lines in between, which is universal style. Only where
properties are booleans, empty lines are not required.
Rob Herring (Arm) [Tue, 31 Dec 2024 16:31:20 +0000 (10:31 -0600)]
phy: Use (of|device)_property_present() for non-boolean properties
The use of (of|device)_property_read_bool() for non-boolean properties
is deprecated in favor of (of|device)_property_present() when testing
for property presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20241231163121.241543-1-robh@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rob Herring (Arm) [Mon, 3 Feb 2025 18:54:21 +0000 (12:54 -0600)]
phy: can-transceiver: Drop unnecessary "mux-states" property presence check
It doesn't matter whether "mux-states" is not present or there is some
other issue parsing it causing an error. Drop the presence check and
rework the error handling to ignore anything other than deferred probe.
Konrad Dybcio [Mon, 3 Feb 2025 14:43:22 +0000 (15:43 +0100)]
phy: qcom: qmp-pcie: Add X1P42100 Gen4x4 PHY
Add a new, common configuration for Gen4x4 V6 PHYs without an init
sequence.
The bootloader configures the hardware once and the OS retains that
configuration by using the NOCSR reset line (which doesn't drop
register state on assert) in place of the "full reset" one.
Use this new configuration for X1P42100's Gen4x4 PHY.
Konrad Dybcio [Mon, 3 Feb 2025 14:43:21 +0000 (15:43 +0100)]
dt-bindings: phy: qcom,qmp-pcie: Drop reset number constraints
(Almost?) all QMP PHYs come with both a "full reset" ("phy") and a
"retain certain registers" one ("phy_nocsr").
Drop the maxItems=1 constraint for resets and reset_names as we go
ahead and straighten out the DT usage. After that's done (which
will involve modifying some clock drivers etc.), we may set
*min*Items to 2, bar some possible exceptions.
Heiko Stuebner [Fri, 6 Dec 2024 10:34:01 +0000 (11:34 +0100)]
phy: phy-rockchip-samsung-hdptx: Don't use dt aliases to determine phy-id
The phy needs to know its identity in the system (phy0 or phy1 on rk3588)
for some actions and the driver currently contains code abusing of_alias
for that.
Devicetree aliases are always optional and should not be used for core
device functionality, so instead keep a list of phys on a soc in the
of_device_data and find the phy-id by comparing against the mapped
register-base.
The variant of the driver in the vendor-tree contained those handy
comments in the regmap register callback. Having the different ranges
describe what they are looks helpful.
Linus Torvalds [Sun, 2 Feb 2025 18:49:13 +0000 (10:49 -0800)]
Merge tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Linus Torvalds [Sun, 2 Feb 2025 18:40:27 +0000 (10:40 -0800)]
Merge tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Len Brown [Sun, 2 Feb 2025 16:43:02 +0000 (10:43 -0600)]
tools/power turbostat: version 2025.02.02
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Linus Torvalds [Sat, 1 Feb 2025 23:07:56 +0000 (15:07 -0800)]
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
Linus Torvalds [Sat, 1 Feb 2025 19:30:41 +0000 (11:30 -0800)]
Merge tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Linus Torvalds [Sat, 1 Feb 2025 18:04:29 +0000 (10:04 -0800)]
Merge tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
Linus Torvalds [Sat, 1 Feb 2025 17:49:20 +0000 (09:49 -0800)]
Merge tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Linus Torvalds [Sat, 1 Feb 2025 17:15:01 +0000 (09:15 -0800)]
Merge tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
Update .mailmap to reflect my new (and final) primary email address,
carlos.bilbao@kernel.org. Also update contact information in files
Documentation/translations/sp_SP/index.rst and MAINTAINERS.
Link: https://lkml.kernel.org/r/20250130012248.1196208-1-carlos.bilbao@kernel.org Signed-off-by: Carlos Bilbao <carlos.bilbao@kernel.org> Cc: Carlos Bilbao <bilbao@vt.edu> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Mattew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
gather_bootmem_prealloc() assumes the start nid as 0 and size as
num_node_state(N_MEMORY). That means in case if memory attached numa
nodes are interleaved, then gather_bootmem_prealloc_parallel() will fail
to scan few of these nodes.
Since memory attached numa nodes can be interleaved in any fashion, hence
ensure that the current code checks for all numa node ids
(.size = nr_node_ids). Let's still keep max_threads as N_MEMORY, so that
it can distributes all nr_node_ids among the these many no. threads.
Zhaoyang Huang [Tue, 21 Jan 2025 02:01:59 +0000 (10:01 +0800)]
mm: gup: fix infinite loop within __get_longterm_locked
We can run into an infinite loop in __get_longterm_locked() when
collect_longterm_unpinnable_folios() finds only folios that are isolated
from the LRU or were never added to the LRU. This can happen when all
folios to be pinned are never added to the LRU, for example when
vm_ops->fault allocated pages using cma_alloc() and never added them to
the LRU.
Fix it by simply taking a look at the list in the single caller, to see if
anything was added.
[zhaoyang.huang@unisoc.com: move definition of local] Link: https://lkml.kernel.org/r/20250122012604.3654667-1-zhaoyang.huang@unisoc.com Link: https://lkml.kernel.org/r/20250121020159.3636477-1-zhaoyang.huang@unisoc.com Fixes: 67e139b02d99 ("mm/gup.c: refactor check_and_migrate_movable_pages()") Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: David Hildenbrand <david@redhat.com> Suggested-by: David Hildenbrand <david@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Aijun Sun <aijun.sun@unisoc.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Kairui Song [Thu, 30 Jan 2025 11:51:31 +0000 (19:51 +0800)]
mm, swap: fix reclaim offset calculation error during allocation
There is a code error that will cause the swap entry allocator to reclaim
and check the whole cluster with an unexpected tail offset instead of the
part that needs to be reclaimed. This may cause corruption of the swap
map, so fix it.
Link: https://lkml.kernel.org/r/20250130115131.37777-1-ryncsn@gmail.com Fixes: 3b644773eefd ("mm, swap: reduce contention on device lock") Signed-off-by: Kairui Song <kasong@tencent.com> Cc: Chris Li <chrisl@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Marco Elver [Fri, 24 Jan 2025 12:01:38 +0000 (13:01 +0100)]
kfence: skip __GFP_THISNODE allocations on NUMA systems
On NUMA systems, __GFP_THISNODE indicates that an allocation _must_ be on
a particular node, and failure to allocate on the desired node will result
in a failed allocation.
Skip __GFP_THISNODE allocations if we are running on a NUMA system, since
KFENCE can't guarantee which node its pool pages are allocated on.
Link: https://lkml.kernel.org/r/20250124120145.410066-1-elver@google.com Fixes: 236e9f153852 ("kfence: skip all GFP_ZONEMASK allocations") Signed-off-by: Marco Elver <elver@google.com> Reported-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: Alexander Potapenko <glider@google.com> Cc: Chistoph Lameter <cl@linux.com> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Nikita Zhandarovich [Fri, 24 Jan 2025 22:20:53 +0000 (07:20 +0900)]
nilfs2: fix possible int overflows in nilfs_fiemap()
Since nilfs_bmap_lookup_contig() in nilfs_fiemap() calculates its result
by being prepared to go through potentially maxblocks == INT_MAX blocks,
the value in n may experience an overflow caused by left shift of blkbits.
While it is extremely unlikely to occur, play it safe and cast right hand
expression to wider type to mitigate the issue.
Found by Linux Verification Center (linuxtesting.org) with static analysis
tool SVACE.
yangge [Sat, 25 Jan 2025 06:53:57 +0000 (14:53 +0800)]
mm: compaction: use the proper flag to determine watermarks
There are 4 NUMA nodes on my machine, and each NUMA node has 32GB of
memory. I have configured 16GB of CMA memory on each NUMA node, and
starting a 32GB virtual machine with device passthrough is extremely slow,
taking almost an hour.
Long term GUP cannot allocate memory from CMA area, so a maximum of 16 GB
of no-CMA memory on a NUMA node can be used as virtual machine memory.
There is 16GB of free CMA memory on a NUMA node, which is sufficient to
pass the order-0 watermark check, causing the __compaction_suitable()
function to consistently return true.
For costly allocations, if the __compaction_suitable() function always
returns true, it causes the __alloc_pages_slowpath() function to fail to
exit at the appropriate point. This prevents timely fallback to
allocating memory on other nodes, ultimately resulting in excessively long
virtual machine startup times.
Call trace:
__alloc_pages_slowpath
if (compact_result == COMPACT_SKIPPED ||
compact_result == COMPACT_DEFERRED)
goto nopage; // should exit __alloc_pages_slowpath() from here
We could use the real unmovable allocation context to have
__zone_watermark_unusable_free() subtract CMA pages, and thus we won't
pass the order-0 check anymore once the non-CMA part is exhausted. There
is some risk that in some different scenario the compaction could in fact
migrate pages from the exhausted non-CMA part of the zone to the CMA part
and succeed, and we'll skip it instead. But only __GFP_NORETRY
allocations should be affected in the immediate "goto nopage" when
compaction is skipped, others will attempt with DEF_COMPACT_PRIORITY
anyway and won't fail without trying to compact-migrate the non-CMA
pageblocks into CMA pageblocks first, so it should be fine.
After this fix, it only takes a few tens of seconds to start a 32GB
virtual machine with device passthrough functionality.
Liam R. Howlett [Mon, 27 Jan 2025 17:02:21 +0000 (12:02 -0500)]
kernel: be more careful about dup_mmap() failures and uprobe registering
If a memory allocation fails during dup_mmap(), the maple tree can be left
in an unsafe state for other iterators besides the exit path. All the
locks are dropped before the exit_mmap() call (in mm/mmap.c), but the
incomplete mm_struct can be reached through (at least) the rmap finding
the vmas which have a pointer back to the mm_struct.
Up to this point, there have been no issues with being able to find an
mm_struct that was only partially initialised. Syzbot was able to make
the incomplete mm_struct fail with recent forking changes, so it has been
proven unsafe to use the mm_struct that hasn't been initialised, as
referenced in the link below.
Although 8ac662f5da19f ("fork: avoid inappropriate uprobe access to
invalid mm") fixed the uprobe access, it does not completely remove the
race.
This patch sets the MMF_OOM_SKIP to avoid the iteration of the vmas on the
oom side (even though this is extremely unlikely to be selected as an oom
victim in the race window), and sets MMF_UNSTABLE to avoid other potential
users from using a partially initialised mm_struct.
When registering vmas for uprobe, skip the vmas in an mm that is marked
unstable. Modifying a vma in an unstable mm may cause issues if the mm
isn't fully initialised.
Link: https://lore.kernel.org/all/6756d273.050a0220.2477f.003d.GAE@google.com/ Link: https://lkml.kernel.org/r/20250127170221.1761366-1-Liam.Howlett@oracle.com Fixes: d24062914837 ("fork: use __mt_dup() to duplicate maple tree in dup_mmap()") Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Jann Horn <jannh@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Peng Zhang <zhangpeng.00@bytedance.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Bruno Faccini [Mon, 27 Jan 2025 17:16:23 +0000 (09:16 -0800)]
mm/fake-numa: handle cases with no SRAT info
Handle more gracefully cases where no SRAT information is available, like
in VMs with no Numa support, and allow fake-numa configuration to complete
successfully in these cases
Link: https://lkml.kernel.org/r/20250127171623.1523171-1-bfaccini@nvidia.com Fixes: 63db8170bf34 (“mm/fake-numa: allow later numa node hotplug”) Signed-off-by: Bruno Faccini <bfaccini@nvidia.com> Cc: David Hildenbrand <david@redhat.com> Cc: Hyeonggon Yoo <hyeonggon.yoo@sk.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Len Brown <lenb@kernel.org> Cc: "Mike Rapoport (IBM)" <rppt@kernel.org> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Zi Yan <ziy@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Catalin Marinas [Mon, 27 Jan 2025 18:42:33 +0000 (18:42 +0000)]
mm: kmemleak: fix upper boundary check for physical address objects
Memblock allocations are registered by kmemleak separately, based on their
physical address. During the scanning stage, it checks whether an object
is within the min_low_pfn and max_low_pfn boundaries and ignores it
otherwise.
With the recent addition of __percpu pointer leak detection (commit 6c99d4eb7c5e ("kmemleak: enable tracking for percpu pointers")), kmemleak
started reporting leaks in setup_zone_pageset() and
setup_per_cpu_pageset(). These were caused by the node_data[0] object
(initialised in alloc_node_data()) ending on the PFN_PHYS(max_low_pfn)
boundary. The non-strict upper boundary check introduced by commit 84c326299191 ("mm: kmemleak: check physical address when scan") causes the
pg_data_t object to be ignored (not scanned) and the __percpu pointers it
contains to be reported as leaks.
Make the max_low_pfn upper boundary check strict when deciding whether to
ignore a physical address object and not scan it.
Link: https://lkml.kernel.org/r/20250127184233.2974311-1-catalin.marinas@arm.com Fixes: 84c326299191 ("mm: kmemleak: check physical address when scan") Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Jakub Kicinski <kuba@kernel.org> Tested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Cc: Patrick Wang <patrick.wang.shcn@gmail.com> Cc: <stable@vger.kernel.org> [6.0.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Hamza Mahfooz [Mon, 20 Jan 2025 20:56:59 +0000 (15:56 -0500)]
mailmap: add an entry for Hamza Mahfooz
Map my previous work email to my current one.
Link: https://lkml.kernel.org/r/20250120205659.139027-1-hamzamahfooz@linux.microsoft.com Signed-off-by: Hamza Mahfooz <hamzamahfooz@linux.microsoft.com> Cc: David S. Miller <davem@davemloft.net> Cc: Hans verkuil <hverkuil@xs4all.nl> Cc: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Li Zhijian [Fri, 10 Jan 2025 12:21:32 +0000 (20:21 +0800)]
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
In shrink_folio_list(), demote_folio_list() can be called 2 times.
Currently stat->nr_demoted will only store the last nr_demoted( the later
nr_demoted is always zero, the former nr_demoted will get lost), as a
result number of demoted pages is not accurate.
Accumulate the nr_demoted count across multiple calls to
demote_folio_list(), ensuring accurate reporting of demotion statistics.
[lizhijian@fujitsu.com: introduce local nr_demoted to fix nr_reclaimed double counting] Link: https://lkml.kernel.org/r/20250111015253.425693-1-lizhijian@fujitsu.com Link: https://lkml.kernel.org/r/20250110122133.423481-1-lizhijian@fujitsu.com Fixes: f77f0c751478 ("mm,memcg: provide per-cgroup counters for NUMA balancing operations") Signed-off-by: Li Zhijian <lizhijian@fujitsu.com> Acked-by: Kaiyang Zhao <kaiyang2@cs.cmu.edu> Tested-by: Donet Tom <donettom@linux.ibm.com> Reviewed-by: Donet Tom <donettom@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Heming Zhao [Tue, 21 Jan 2025 11:22:03 +0000 (19:22 +0800)]
ocfs2: fix incorrect CPU endianness conversion causing mount failure
Commit 23aab037106d ("ocfs2: fix UBSAN warning in ocfs2_verify_volume()")
introduced a regression bug. The blksz_bits value is already converted to
CPU endian in the previous code; therefore, the code shouldn't use
le32_to_cpu() anymore.
Link: https://lkml.kernel.org/r/20250121112204.12834-1-heming.zhao@suse.com Fixes: 23aab037106d ("ocfs2: fix UBSAN warning in ocfs2_verify_volume()") Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Hyeonggon Yoo [Mon, 27 Jan 2025 23:16:31 +0000 (08:16 +0900)]
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
Commit c1b3bb73d55e ("mm/zsmalloc: use zpdesc in
trylock_zspage()/lock_zspage()") introduces is_first_zpdesc() function.
However, the function is only used when CONFIG_DEBUG_VM=y.
When building with LLVM=1 and W=1 option, the following warning is
generated:
$ make -j12 W=1 LLVM=1 mm/zsmalloc.o
mm/zsmalloc.c:455:20: error: function 'is_first_zpdesc' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
455 | static inline bool is_first_zpdesc(struct zpdesc *zpdesc)
| ^~~~~~~~~~~~~~~
1 error generated.
Fix the warning by adding __maybe_unused attribute to the function.
No functional change intended.
Link: https://lkml.kernel.org/r/20250127231631.4363-1-42.hyeyoo@gmail.com Fixes: c1b3bb73d55e ("mm/zsmalloc: use zpdesc in trylock_zspage()/lock_zspage()") Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202501240958.4ILzuBrH-lkp@intel.com/ Cc: Alex Shi <alexs@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
liuye [Tue, 19 Nov 2024 06:08:42 +0000 (14:08 +0800)]
mm/vmscan: fix hard LOCKUP in function isolate_lru_folios
This fixes the following hard lockup in isolate_lru_folios() during memory
reclaim. If the LRU mostly contains ineligible folios this may trigger
watchdog.
watchdog: Watchdog detected hard LOCKUP on cpu 173
RIP: 0010:native_queued_spin_lock_slowpath+0x255/0x2a0
Call Trace:
_raw_spin_lock_irqsave+0x31/0x40
folio_lruvec_lock_irqsave+0x5f/0x90
folio_batch_move_lru+0x91/0x150
lru_add_drain_per_cpu+0x1c/0x40
process_one_work+0x17d/0x350
worker_thread+0x27b/0x3a0
kthread+0xe8/0x120
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1b/0x30
Scenario:
User processe are requesting a large amount of memory and keep page active.
Then a module continuously requests memory from ZONE_DMA32 area.
Memory reclaim will be triggered due to ZONE_DMA32 watermark alarm reached.
However pages in the LRU(active_anon) list are mostly from
the ZONE_NORMAL area.
About the Fixes:
Why did it take eight years to be discovered?
The problem requires the following conditions to occur:
1. The device memory should be large enough.
2. Pages in the LRU(active_anon) list are mostly from the ZONE_NORMAL area.
3. The memory in ZONE_DMA32 needs to reach the watermark.
If the memory is not large enough, or if the usage design of ZONE_DMA32
area memory is reasonable, this problem is difficult to detect.
notes:
The problem is most likely to occur in ZONE_DMA32 and ZONE_NORMAL,
but other suitable scenarios may also trigger the problem.
Link: https://lkml.kernel.org/r/20241119060842.274072-1-liuye@kylinos.cn Fixes: b2e18757f2c9 ("mm, vmscan: begin reclaiming pages on a per-node basis") Signed-off-by: liuye <liuye@kylinos.cn> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Yang Shi <yang@os.amperecomputing.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Geert Uytterhoeven [Fri, 24 Jan 2025 08:39:19 +0000 (09:39 +0100)]
sh: boards: Use imply to enable hardware with complex dependencies
If CONFIG_I2C=n:
WARNING: unmet direct dependencies detected for SND_SOC_AK4642
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && I2C [=n]
Selected by [y]:
- SH_7724_SOLUTION_ENGINE [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
WARNING: unmet direct dependencies detected for SND_SOC_DA7210
Depends on [n]: SOUND [=y] && SND [=y] && SND_SOC [=y] && SND_SOC_I2C_AND_SPI [=n]
Selected by [y]:
- SH_ECOVEC [=y] && CPU_SUBTYPE_SH7724 [=y] && SND_SIMPLE_CARD [=y]
Fix this by replacing select by imply, instead of adding a dependency on
I2C.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202501240836.OvXqmANX-lkp@intel.com/ Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Masahiro Yamada [Sun, 22 Dec 2024 00:32:07 +0000 (09:32 +0900)]
sh: Migrate to the generic rule for built-in DTB
Commit 654102df2ac2 ("kbuild: add generic support for built-in
boot DTBs") introduced generic support for built-in DTBs.
Select GENERIC_BUILTIN_DTB when built-in DTB support is enabled.
To keep consistency across architectures, this commit also renames
CONFIG_USE_BUILTIN_DTB to CONFIG_BUILTIN_DTB, and
CONFIG_BUILTIN_DTB_SOURCE to CONFIG_BUILTIN_DTB_NAME.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
David Wang [Sat, 30 Nov 2024 13:49:09 +0000 (21:49 +0800)]
sh: irq: Use seq_put_decimal_ull_width() for decimal values
On a system with n CPUs and m interrupts, there will be n*m decimal
values yielded via seq_printf(.."%10u "..) which has significant costs
parsing format string and is less efficient than seq_put_decimal_ull_width().
Stress reading /proc/interrupts indicates ~30% performance improvement with
this patch.
Signed-off-by: David Wang <00107082@163.com> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
* tag 'for-linus-hexagon-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/bcain/linux:
MAINTAINERS: Update my email address
hexagon: Fix unbalanced spinlock in die()
hexagon: Fix warning comparing pointer to 0
hexagon: Move kernel prototypes out of uapi/asm/setup.h header
hexagon: time: Remove redundant null check for resource
hexagon: fix using plain integer as NULL pointer warning in cmpxchg
Linus Torvalds [Sat, 1 Feb 2025 03:49:17 +0000 (19:49 -0800)]
Remove stale generated 'genheaders' file
This bogus stale file was added in commit 101971298be2 ("riscv: add a
warning when physical memory address overflows"). It's the old location
for what is now 'security/selinux/genheaders'.
It looks like it got incorrectly committed back when that file was in
the old location, and then rebasing kept the bogus file alive.
Reported-by: Eric Biggers <ebiggers@kernel.org> Link: https://lore.kernel.org/linux-riscv/20250201020003.GA77370@sol.localdomain/ Fixes: 101971298be2 ("riscv: add a warning when physical memory address overflows") Cc: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 1 Feb 2025 01:10:26 +0000 (17:10 -0800)]
Merge tag 'hardening-v6.14-rc1-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
"This is a fix for the soon to be released GCC 15 which has regressed
its initialization of unions when performing explicit initialization
(i.e. a general problem, not specifically a hardening problem; we're
just carrying the fix).
Details in the final patch, Acked by Masahiro, with updated selftests
to validate the fix"
* tag 'hardening-v6.14-rc1-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
kbuild: Use -fzero-init-padding-bits=all
stackinit: Add union initialization to selftests
stackinit: Add old-style zero-init syntax to struct tests
* tag 'drm-next-2025-02-01' of https://gitlab.freedesktop.org/drm/kernel:
drm/amd/display: restore invalid MSA timing check for freesync
drm/amdkfd: only flush the validate MES contex
drm/amd/display: Correct register address in dcn35
drm/amd/pm: Mark MM activity as unsupported
drm/amd/amdgpu: change the config of cgcg on gfx12
drm/amdkfd: Block per-queue reset when halt_if_hws_hang=1
Linus Torvalds [Fri, 31 Jan 2025 23:39:50 +0000 (15:39 -0800)]
Merge tag 'pci-v6.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Save the original INTX_DISABLE bit at the first pcim_intx() call and
restore that at devres cleanup instead of restoring the opposite of
the most recent enable/disable pcim_intx() argument, which was wrong
when a driver called pcim_intx() multiple times or with the already
enabled state (Takashi Iwai)
* tag 'pci-v6.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Restore original INTX_DISABLE bit by pcim_intx()
Linus Torvalds [Fri, 31 Jan 2025 23:13:25 +0000 (15:13 -0800)]
Merge tag 'riscv-for-linus-6.14-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- The PH1520 pinctrl and dwmac drivers are enabeled in defconfig
- A redundant AQRL barrier has been removed from the futex cmpxchg
implementation
- Support for the T-Head vector extensions, which includes exposing
these extensions to userspace on systems that implement them
- Some more page table information is now printed on die() and systems
that cause PA overflows
* tag 'riscv-for-linus-6.14-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: add a warning when physical memory address overflows
riscv/mm/fault: add show_pte() before die()
riscv: Add ghostwrite vulnerability
selftests: riscv: Support xtheadvector in vector tests
selftests: riscv: Fix vector tests
riscv: hwprobe: Document thead vendor extensions and xtheadvector extension
riscv: hwprobe: Add thead vendor extension probing
riscv: vector: Support xtheadvector save/restore
riscv: Add xtheadvector instruction definitions
riscv: csr: Add CSR encodings for CSR_VXRM/CSR_VXSAT
RISC-V: define the elements of the VCSR vector CSR
riscv: vector: Use vlenb from DT for thead
riscv: Add thead and xtheadvector as a vendor extension
riscv: dts: allwinner: Add xtheadvector to the D1/D1s devicetree
dt-bindings: cpus: add a thead vlen register length property
dt-bindings: riscv: Add xtheadvector ISA extension description
RISC-V: Mark riscv_v_init() as __init
riscv: defconfig: drop RT_GROUP_SCHED=y
riscv/futex: Optimize atomic cmpxchg
riscv: defconfig: enable pinctrl and dwmac support for TH1520
Tomasz has reported that his device, Generalplus Technology Inc. 808 Camera,
with ID 1b3f:2002, stopped being detected:
$ ls -l /dev/video*
zsh: no matches found: /dev/video*
[ 7.230599] usb 3-2: Found multiple Units with ID 5
This particular device is non-compliant, having both the Output Terminal
and Processing Unit with ID 5. uvc_scan_fallback, though, is able to build
a chain. However, when media elements are added and uvc_mc_create_links
call uvc_entity_by_id, it will get the incorrect entity,
media_create_pad_link will WARN, and it will fail to register the entities.
In order to reinstate support for such devices in a timely fashion,
reverting the fix for these warnings is appropriate. A proper fix that
considers the existence of such non-compliant devices will be submitted in
a later development cycle.
Reported-by: Tomasz Sikora <sikora.tomus@gmail.com> Fixes: 3dd075fe8ebb ("media: uvcvideo: Require entities to have a non-zero unique ID") Cc: stable@vger.kernel.org Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ricardo Ribalda <ribalda@chromium.org> Link: https://lore.kernel.org/r/20250114200045.1401644-1-cascardo@igalia.com Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Linus Torvalds [Fri, 31 Jan 2025 20:07:07 +0000 (12:07 -0800)]
Merge tag 'kbuild-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Support multiple hook locations for maint scripts of Debian package
- Remove 'cpio' from the build tool requirement
- Introduce gendwarfksyms tool, which computes CRCs for export symbols
based on the DWARF information
- Support CONFIG_MODVERSIONS for Rust
- Resolve all conflicts in the genksyms parser
- Fix several syntax errors in genksyms
* tag 'kbuild-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (64 commits)
kbuild: fix Clang LTO with CONFIG_OBJTOOL=n
kbuild: Strip runtime const RELA sections correctly
kconfig: fix memory leak in sym_warn_unmet_dep()
kconfig: fix file name in warnings when loading KCONFIG_DEFCONFIG_LIST
genksyms: fix syntax error for attribute before init-declarator
genksyms: fix syntax error for builtin (u)int*x*_t types
genksyms: fix syntax error for attribute after 'union'
genksyms: fix syntax error for attribute after 'struct'
genksyms: fix syntax error for attribute after abstact_declarator
genksyms: fix syntax error for attribute before nested_declarator
genksyms: fix syntax error for attribute before abstract_declarator
genksyms: decouple ATTRIBUTE_PHRASE from type-qualifier
genksyms: record attributes consistently for init-declarator
genksyms: restrict direct-declarator to take one parameter-type-list
genksyms: restrict direct-abstract-declarator to take one parameter-type-list
genksyms: remove Makefile hack
genksyms: fix last 3 shift/reduce conflicts
genksyms: fix 6 shift/reduce conflicts and 5 reduce/reduce conflicts
genksyms: reduce type_qualifier directly to decl_specifier
genksyms: rename cvar_qualifier to type_qualifier
...
Linus Torvalds [Fri, 31 Jan 2025 19:49:30 +0000 (11:49 -0800)]
Merge tag 'block-6.14-20250131' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Song:
- Fix a md-cluster regression introduced
- More sysfs race fixes
- Mark anything inside queue freezing as not being able to do IO for
memory allocations
- Fix for a regression introduced in loop in this merge window
- Fix for a regression in queue mapping setups introduced in this merge
window
- Fix for the block dio fops attempting an iov_iter revert upton
getting -EIOCBQUEUED on the read side. This one is going to stable as
well
* tag 'block-6.14-20250131' of git://git.kernel.dk/linux:
block: force noio scope in blk_mq_freeze_queue
block: fix nr_hw_queue update racing with disk addition/removal
block: get rid of request queue ->sysfs_dir_lock
loop: don't clear LO_FLAGS_PARTSCAN on LOOP_SET_STATUS{,64}
md/md-bitmap: Synchronize bitmap_get_stats() with bitmap lifetime
blk-mq: create correct map for fallback case
block: don't revert iter for -EIOCBQUEUED
Linus Torvalds [Fri, 31 Jan 2025 19:29:23 +0000 (11:29 -0800)]
Merge tag 'io_uring-6.14-20250131' of git://git.kernel.dk/linux
Pull more io_uring updates from Jens Axboe:
- Series cleaning up the alloc cache changes from this merge window,
and then another series on top making it better yet.
This also solves an issue with KASAN_EXTRA_INFO, by making io_uring
resilient to KASAN using parts of the freed struct for storage
- Cleanups and simplications to buffer cloning and io resource node
management
- Fix an issue introduced in this merge window where READ/WRITE_ONCE
was used on an atomic_t, which made some archs complain
- Fix for an errant connect retry when the socket has been shut down
- Fix for multishot and provided buffers
* tag 'io_uring-6.14-20250131' of git://git.kernel.dk/linux:
io_uring/net: don't retry connect operation on EPOLLERR
io_uring/rw: simplify io_rw_recycle()
io_uring: remove !KASAN guards from cache free
io_uring/net: extract io_send_select_buffer()
io_uring/net: clean io_msg_copy_hdr()
io_uring/net: make io_net_vec_assign() return void
io_uring: add alloc_cache.c
io_uring: dont ifdef io_alloc_cache_kasan()
io_uring: include all deps for alloc_cache.h
io_uring: fix multishots with selected buffers
io_uring/register: use atomic_read/write for sq_flags migration
io_uring/alloc_cache: get rid of _nocache() helper
io_uring: get rid of alloc cache init_once handling
io_uring/uring_cmd: cleanup struct io_uring_cmd_data layout
io_uring/uring_cmd: use cached cmd_op in io_uring_cmd_sock()
io_uring/msg_ring: don't leave potentially dangling ->tctx pointer
io_uring/rsrc: Move lockdep assert from io_free_rsrc_node() to caller
io_uring/rsrc: remove unused parameter ctx for io_rsrc_node_alloc()
io_uring: clean up io_uring_register_get_file()
io_uring/rsrc: Simplify buffer cloning by locking both rings
Masahiro Yamada [Fri, 31 Jan 2025 14:04:01 +0000 (23:04 +0900)]
kbuild: fix Clang LTO with CONFIG_OBJTOOL=n
Since commit bede169618c6 ("kbuild: enable objtool for *.mod.o and
additional kernel objects"), Clang LTO builds do not perform any
optimizations when CONFIG_OBJTOOL is disabled (e.g., for ARCH=arm64).
This is because every LLVM bitcode file is immediately converted to
ELF format before the object files are linked together.
This commit fixes the breakage.
Fixes: bede169618c6 ("kbuild: enable objtool for *.mod.o and additional kernel objects") Reported-by: Yonghong Song <yonghong.song@linux.dev> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Yonghong Song <yonghong.song@linux.dev>
Due to the fact that runtime const ELF sections are named without a
leading period or double underscore, the RSTRIP logic that removes the
static RELA sections from vmlinux fails to identify them. This results
in a situation like below, where some sections that were supposed to get
removed are left behind.
So tweak the match expression to strip all sections starting with .rel.
While at it, consolidate the logic used by RISC-V, s390 and x86 into a
single shared Makefile library command.
Linus Torvalds [Fri, 31 Jan 2025 19:07:56 +0000 (11:07 -0800)]
Merge tag 'ata-6.14-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull more ata updates from Niklas Cassel:
- Add ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives (Daniel)
- Ensure that PIO transfers using libata-sff cannot write outside the
allocated buffer (me)
* tag 'ata-6.14-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-sff: Ensure that we cannot write outside the allocated buffer
ata: libata-core: Add ATA_QUIRK_NOLPM for Samsung SSD 870 QVO drives
cifs: Fix parsing native symlinks directory/file type
As SMB protocol distinguish between symlink to directory and symlink to
file, add some mechanism to disallow resolving incompatible types.
When SMB symlink is of the directory type, ensure that its target path ends
with slash. This forces Linux to not allow resolving such symlink to file.
And when SMB symlink is of the file type and its target path ends with
slash then returns an error as such symlink is unresolvable. Such symlink
always points to invalid location as file cannot end with slash.
As POSIX server does not distinguish between symlinks to file and symlink
directory, do not apply this change for symlinks from POSIX SMB server. For
POSIX SMB servers, this change does nothing.
This mimics Windows behavior of native SMB symlinks.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
This change implements support for creating new symlink in WSL-style by
Linux cifs client when -o reparse=wsl mount option is specified. WSL-style
symlink uses reparse point with tag IO_REPARSE_TAG_LX_SYMLINK and symlink
target location is stored in reparse buffer in UTF-8 encoding prefixed by
32-bit flags. Flags bits are unknown, but it was observed that WSL always
sets flags to value 0x02000000. Do same in Linux cifs client.
New symlinks would be created in WSL-style only in case the mount option
-o reparse=wsl is specified, which is not by default. So default CIFS
mounts are not affected by this change.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Tue, 28 Jan 2025 07:04:23 +0000 (01:04 -0600)]
smb3: add support for IAKerb
There are now more servers which advertise support for IAKerb (passthrough
Kerberos authentication via proxy). IAKerb is a public extension industry
standard Kerberos protocol that allows a client without line-of-sight
to a Domain Controller to authenticate. There can be cases where we
would fail to mount if the server only advertises the OID for IAKerb
in SPNEGO/GSSAPI. Add code to allow us to still upcall to userspace
in these cases to obtain the Kerberos ticket.
Signed-off-by: Steve French <stfrench@microsoft.com>
Pali Rohár [Sun, 29 Dec 2024 14:31:05 +0000 (15:31 +0100)]
cifs: Fix struct FILE_ALL_INFO
struct FILE_ALL_INFO for level 263 (0x107) used by QPathInfo does not have
any IndexNumber, AccessFlags, IndexNumber1, CurrentByteOffset, Mode or
AlignmentRequirement members. So remove all of them.
Also adjust code in move_cifs_info_to_smb2() function which converts struct
FILE_ALL_INFO to struct smb2_file_all_info.
Fixed content of struct FILE_ALL_INFO was verified that is correct against:
* [MS-CIFS] section 2.2.8.3.10 SMB_QUERY_FILE_ALL_INFO
* Samba server implementation of trans2 query file/path for level 263
* Packet structure tests against Windows SMB servers
This change fixes CIFSSMBQFileInfo() and CIFSSMBQPathInfo() functions which
directly copy received FILE_ALL_INFO network buffers into kernel structures
of FILE_ALL_INFO type.
struct FILE_ALL_INFO is the response structure returned by the SMB server.
So the incorrect definition of this structure can lead to returning bogus
information in stat() call.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
projects / users / jedix / linux-maple.git / log