Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.
The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655e3
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.
It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.
There have been reports of the WFI timing out on some boards, and a
patch was proposed to just remove it. This stuff is rather fragile,
and I believe the WFI might be needed with our FW prior to GM200.
However, we probably should not be touching PMU during init on GPUs
where we depend on NVIDIA FW, outside of limited circumstances, so
this should be a somewhat safer change that achieves the desired
result.
Reported-by: Diego Viola <diego.viola@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Link: https://gitlab.freedesktop.org/drm/nouveau/-/merge_requests/10 Signed-off-by: Sasha Levin <sashal@kernel.org>
I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.
After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.
The issue is that we received a DLM message for a user lock but the
destination lock is a kernel lock. Note that the address which is trying
to derefence is 00000000deadbeef, which is in a kernel lock
lkb->lkb_astparam, this field should never be derefenced by the DLM
kernel stack. In case of a user lock lkb->lkb_astparam is lkb->lkb_ua
(memory is shared by a union field). The struct lkb_ua will be handled
by the DLM kernel stack but on a kernel lock it will contain invalid
data and ends in most likely crashing the kernel.
The MIPS BMC63XX subarch does not provide/support clk_set_parent().
This causes build errors in a few drivers, so add a simple implementation
of that function so that callers of it will build without errors.
Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." ) Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When firmware load failed, kernel report task hung as follows:
INFO: task xrun:5191 blocked for more than 147 seconds.
Tainted: G W 5.16.0-rc5-next-20211220+ #11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:xrun state:D stack: 0 pid: 5191 ppid: 270 flags:0x00000004
Call Trace:
__schedule+0xc12/0x4b50 kernel/sched/core.c:4986
schedule+0xd7/0x260 kernel/sched/core.c:6369 (discriminator 1)
schedule_timeout+0x7aa/0xa80 kernel/time/timer.c:1857
wait_for_completion+0x181/0x290 kernel/sched/completion.c:85
lattice_ecp3_remove+0x32/0x40 drivers/misc/lattice-ecp3-config.c:221
spi_remove+0x72/0xb0 drivers/spi/spi.c:409
lattice_ecp3_remove() wait for signals from firmware loading, but when
load failed, firmware_load() does not send this signal. This cause
device remove hung. Fix it by sending signal even if load failed.
Because of the potential failure of the ioremap(), the buf->area could
be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.
Fixes: f09aecd50f39 ("ASoC: SAMSUNG: Add I2S0 internal dma driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20211228034026.1659385-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out to be possible for hotplugging out a device to reach the
stage of tearing down the device's group and default domain before the
domain's flush queue has drained naturally. At this point, it is then
possible for the timeout to expire just before the del_timer() call
in free_iova_flush_queue(), such that we then proceed to free the FQ
resources while fq_flush_timeout() is still accessing them on another
CPU. Crashes due to this have been observed in the wild while removing
NVMe devices.
Close the race window by using del_timer_sync() to safely wait for any
active timeout handler to finish before we start to free things. We
already avoid any locking in free_iova_flush_queue() since the FQ is
supposed to be inactive anyway, so the potential deadlock scenario does
not apply.
The last driver referencing the slave_id on Marvell PXA and MMP platforms
was the SPI driver, but this stopped doing so a long time ago, so the
TODO from the earlier patch can no be removed.
Fixes: b729bf34535e ("spi/pxa2xx: Don't use slave_id of dma_slave_config") Fixes: 13b3006b8ebd ("dma: mmp_pdma: add filter function") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20211122222203.4103644-7-arnd@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value of device_property_read_u32_array() is not always 0.
To catch the exception in case that devm_kzalloc failed and the
rt5663->imp_table was NULL, which caused the failure of
device_property_read_u32_array.
Fixes: 450f0f6a8fb4 ("ASoC: rt5663: Add the manual offset field to compensate the DC offset") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20211215031550.70702-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, ib_find_gid() will stop searching after encountering the first
empty GID table entry. This behavior is wrong since neither IB nor RoCE
spec enforce tightly packed GID tables.
For example, when a valid GID entry exists at index N, and if a GID entry
is empty at index N-1, ib_find_gid() will fail to find the valid entry.
Fix it by making ib_find_gid() continue searching even after encountering
missing entries.
Fixes: 5eb620c81ce3 ("IB/core: Add helpers for uncached GID and P_Key searches") Link: https://lore.kernel.org/r/e55d331b96cecfc2cf19803d16e7109ea966882d.1639055490.git.leonro@nvidia.com Signed-off-by: Avihai Horon <avihaih@nvidia.com> Reviewed-by: Mark Zhang <markzhang@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver data pointer must be set before any callbacks are registered
that use that pointer. Hence move the initialization of that pointer from
after the ufshcd_init() call to inside ufshcd_init().
Link: https://lore.kernel.org/r/20211203231950.193369-7-bvanassche@acm.org Fixes: 3b1d05807a9a ("[SCSI] ufs: Segregate PCI Specific Code") Reported-by: Alexey Dobriyan <adobriyan@gmail.com> Tested-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Table descriptors were being installed without properly formatting the
address using paddr_to_iopte, which does not match up with the
iopte_deref in __arm_lpae_map. This is incorrect for the LPAE pte
format, as it does not handle the high bits properly.
This was found on Apple T6000 DARTs, which require a new pte format
(different shift); adding support for that to
paddr_to_iopte/iopte_to_paddr caused it to break badly, as even <48-bit
addresses would end up incorrect in that case.
Fixes: 6c89928ff7a0 ("iommu/io-pgtable-arm: Support 52-bit physical address") Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20211120031343.88034-1-marcan@marcan.st Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using MKWORD() on a byte-sized variable results in OOB read. Expand the
size of the reserved area so both MKWORD and MKBYTE continue to work
without overflow. Silences this warning on a -Warray-bounds build:
drivers/char/mwave/3780i.h:346:22: error: array subscript 'short unsigned int[0]' is partly outside array bounds of 'DSP_ISA_SLAVE_CONTROL[1]' [-Werror=array-bounds]
346 | #define MKWORD(var) (*((unsigned short *)(&var)))
| ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/char/mwave/3780i.h:356:40: note: in definition of macro 'OutWordDsp'
356 | #define OutWordDsp(index,value) outw(value,usDspBaseIO+index)
| ^~~~~
drivers/char/mwave/3780i.c:373:41: note: in expansion of macro 'MKWORD'
373 | OutWordDsp(DSP_IsaSlaveControl, MKWORD(rSlaveControl));
| ^~~~~~
drivers/char/mwave/3780i.c:358:31: note: while referencing 'rSlaveControl'
358 | DSP_ISA_SLAVE_CONTROL rSlaveControl;
| ^~~~~~~~~~~~~
Fix compile error when OSS_DEBUG is enabled:
sound/core/oss/pcm_oss.c: In function 'snd_pcm_oss_set_trigger':
sound/core/oss/pcm_oss.c:2055:10: error: 'substream' undeclared (first
use in this function); did you mean 'csubstream'?
pcm_dbg(substream->pcm, "pcm_oss: trigger = 0x%x\n", trigger);
^
Commit f37fe2f9987b ("ASoC: uniphier: add support for UniPhier AIO common
driver") adds configs SND_SOC_UNIPHIER_{LD11,PXS2}, which select the
non-existing config SND_SOC_UNIPHIER_AIO_DMA.
Probably, there is actually no further config intended to be selected
here. So, just drop selecting the non-existing config.
Fixes: f37fe2f9987b ("ASoC: uniphier: add support for UniPhier AIO common driver") Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Link: https://lore.kernel.org/r/20211125095158.8394-2-lukas.bulwahn@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
prom_getprop() can return PROM_ERROR. Binary operator can not identify
it.
Fixes: 94d2dde738a5 ("[POWERPC] Efika: prune fixups and make them more carefull") Signed-off-by: Peiwei Hu <jlu.hpw@foxmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/tencent_BA28CC6897B7C95A92EB8C580B5D18589105@qq.com Signed-off-by: Sasha Levin <sashal@kernel.org>
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
A user reported FITRIM ioctl failing for him on ext4 on some devices
without apparent reason. After some debugging we've found out that
these devices (being LVM volumes) report rather large discard
granularity of 42MB and the filesystem had 1k blocksize and thus group
size of 8MB. Because ext4 FITRIM implementation puts discard
granularity into minlen, ext4_trim_fs() declared the trim request as
invalid. However just silently doing nothing seems to be a more
appropriate reaction to such combination of parameters since user did
not specify anything wrong.
CC: Lukas Czerner <lczerner@redhat.com> Fixes: 5c2ed62fd447 ("ext4: Adjust minlen with discard_granularity in the FITRIM ioctl") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20211112152202.26614-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com Fixes: 2a36d7083438 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to set TASK_INTERRUPTIBLE before calling kthread_should_stop().
Otherwise, kthread_stop() might see that the pccardd thread is still
in TASK_RUNNING state and fail to wake it up.
Additionally, we only need to set the state back to TASK_RUNNING if
kthread_should_stop() breaks the loop.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Fixes: d3046ba809ce ("pcmcia: fix a boot time warning in pcmcia cs code") Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de Fixes: 03fd3cf5a179 ("can: add driver for Softing card") Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Locality is not appropriately requested before writing the int mask.
Add the missing boilerplate.
Fixes: e6aef069b6e9 ("tpm_tis: convert to using locality callbacks") Signed-off-by: Chen Jun <chenjun102@huawei.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for meson_spifc_probe.
Fixes: c3e4bc5434d2 ("spi: meson: Add support for Amlogic Meson SPIFC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220107075424.7774-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
As the possible failure of the allocation, the devm_ioremap() may return
NULL pointer.
Take tgec_initialization() as an example.
If allocation fails, the params->base_addr will be NULL pointer and will
be assigned to tgec->regs in tgec_config().
Then it will cause the dereference of NULL pointer in set_mac_address(),
which is called by tgec_init().
Therefore, it should be better to add the sanity check after the calling
of the devm_ioremap().
Fixes: 3933961682a3 ("fsl/fman: Add FMan MAC driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the possible alloc failure of devm_kcalloc(), it could return null
pointer.
Therefore, 'strings' should be checked and return NULL if alloc fails to
prevent the dereference of the NULL pointer.
Also, the caller should also deal with the return value of the
gb_generate_enum_strings() and return -ENOMEM if returns NULL.
Moreover, because the memory allocated with devm_kzalloc() will be
freed automatically when the last reference to the device is dropped,
the 'gbe' in gbaudio_tplg_create_enum_kctl() and
gbaudio_tplg_create_enum_ctl() do not need to free manually.
But the 'control' in gbaudio_tplg_create_widget() and
gbaudio_tplg_process_kcontrols() has a specially error handle to
cleanup.
So it should be better to cleanup 'control' when fails.
The issue takes place in one error path of clusterip_tg_check(). When
memcmp() returns nonzero, the function simply returns the error code,
forgetting to decrease the reference count of a clusterip_config
object, which is bumped earlier by clusterip_config_find_get(). This
may incur reference count leak.
Fix this issue by decrementing the refcount of the object in specific
error path.
Fixes: 06aa151ad1fc74 ("netfilter: ipt_CLUSTERIP: check MAC address when duplicate config is set") Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In nonstatic_find_mem_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In __nonstatic_find_io_region(), pcmcia_make_resource() is assigned to
res and used in pci_bus_alloc_resource(). There is a dereference of res
in pci_bus_alloc_resource(), which could lead to a NULL pointer
dereference on failure of pcmcia_make_resource().
Fix this bug by adding a check of res.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_PCCARD_NONSTATIC=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 49b1153adfe1 ("pcmcia: move all pcmcia_resource_ops providers into one module") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
[linux@dominikbrodowski.net: Fix typo in commit message] Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoC") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20211217202717.10041-3-s.shtylyov@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In msi001_probe(), if the creation of control for bandwidth_auto
fails, there will be a null-ptr-deref issue when it is used in
v4l2_ctrl_auto_cluster().
Check dev->hdl.error before v4l2_ctrl_auto_cluster() to fix this bug.
Link: https://lore.kernel.org/linux-media/20211026112348.2878040-1-wanghai38@huawei.com Fixes: 93203dd6c7c4 ("[media] msi001: Mirics MSi001 silicon tuner driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dvb_usb_device_init stores parts of properties at d->props
and d->desc and uses it on dvb_usb_device_exit.
Free of properties on module probe leads to use after free.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204597
The patch makes properties static instead of allocated on heap to prevent
memleak and use after free.
Also fixes s421_properties.devices initialization to have 2 element
instead of 6 copied from p7500_properties.
[mchehab: fix function call alignments] Link: https://lore.kernel.org/linux-media/20190822104147.4420-1-vasilyev@ispras.ru Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru> Fixes: 299c7007e936 ("media: dw2102: Fix memleak on sequence of probes") Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
copy_user_offload() will actually push a struct struct xfrm_user_offload,
which is different than (struct xfrm_state *)->xso
(struct xfrm_state_offload)
When rt_runtime is modified from -1 to a valid control value, it may
cause the task to be throttled all the time. Operations like the following
will trigger the bug. E.g:
1. echo -1 > /proc/sys/kernel/sched_rt_runtime_us
2. Run a FIFO task named A that executes while(1)
3. echo 950000 > /proc/sys/kernel/sched_rt_runtime_us
When rt_runtime is -1, The rt period timer will not be activated when task
A enqueued. And then the task will be throttled after setting rt_runtime to
950,000. The task will always be throttled because the rt period timer is
not activated.
Fixes: d0b27fa77854 ("sched: rt-group: synchonised bandwidth period") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Li Hua <hucool.lihua@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20211203033618.11895-1-hucool.lihua@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit e955f959ac52 ("media: si2157: Better check for running tuner in
init") completely broke the "warm" tuner detection of the si2157 driver
due to a simple endian error: The Si2157 CRYSTAL_TRIM property code is
0x0402 and needs to be transmitted LSB first. However, it was inserted
MSB first, causing the warm detection to always fail and spam the kernel
log with tuner initialization messages each time the DVB frontend
device was closed and reopened:
[ 312.215682] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 312.264334] si2157 16-0060: firmware version: 3.0.5
[ 342.248593] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 342.295743] si2157 16-0060: firmware version: 3.0.5
[ 372.328574] si2157 16-0060: found a 'Silicon Labs Si2157-A30'
[ 372.385035] si2157 16-0060: firmware version: 3.0.5
Also, the reinitializations were observed disturb _other_ tuners on
multi-tuner cards such as the Hauppauge WinTV-QuadHD, leading to missed
or errored packets when one of the other DVB frontend devices on that
card was opened.
Fix the order of the property code bytes to make the warm detection work
again, also reducing the tuner initialization message in the kernel log
to once per power-on, as well as fixing the interference with other
tuners.
In mxb_attach(dev, info), saa7146_vv_init() is called to allocate a
new memory for dev->vv_data. saa7146_vv_release() will be called on
failure of mxb_probe(dev). There is a dereference of dev->vv_data
in saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init().
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_MXB=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 03b1930efd3c ("V4L/DVB: saa7146: fix regression of the av7110/budget-av driver") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dib8000_init(), the variable fe is not freed or passed out on the
failure of dib8000_identify(&state->i2c), which could lead to a memleak.
Fix this bug by adding a kfree of fe in the error path.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DVB_DIB8000=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 77e2c0f5d471 ("V4L/DVB (12900): DiB8000: added support for DiBcom ISDB-T/ISDB-Tsb demodulator DiB8000") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the watchdog detects a disk change, it calls cancel_activity(),
which in turn tries to cancel the fd_timer delayed work.
In the above scenario, fd_timer_fn is set to fd_watchdog(), meaning
it is trying to cancel its own work.
This results in a hang as cancel_delayed_work_sync() is waiting for the
watchdog (itself) to return, which never happens.
This can be reproduced relatively consistently by attempting to read a
broken floppy, and ejecting it while IO is being attempted and retried.
To resolve this, this patch calls cancel_delayed_work() instead, which
cancels the work without waiting for the watchdog to return and finish.
Before this regression was introduced, the code in this section used
del_timer(), and not del_timer_sync() to delete the watchdog timer.
Link: https://lore.kernel.org/r/399e486c-6540-db27-76aa-7a271b061f76@tasossah.com Fixes: 070ad7e793dc ("floppy: convert to delayed work and single-thread wq") Signed-off-by: Tasos Sahanidis <tasos@tasossah.com> Signed-off-by: Denis Efremov <efremov@linux.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()") the
function devm_ioremap() called from pl011_setup_port() was replaced with
devm_ioremap_resource(). Since this function not only remaps but also
requests the ports io memory region it now collides with the .config_port()
callback which requests the same region at uart port registration.
Since devm_ioremap_resource() already claims the memory successfully, the
request in .config_port() fails.
Later at uart port deregistration the attempt to release the unclaimed
memory also fails. The failure results in a “Trying to free nonexistent
resource" warning.
Fix these issues by removing the callbacks that implement the redundant
memory allocation/release. Also make sure that changing the drivers io
memory base address via TIOCSSERIAL is not allowed any more.
The base address of uartlite registers could be 64 bit address which is from
device resource. When ulite_probe() calls ulite_assign(), this 64 bit
address is casted to 32-bit. The fix is to replace "u32" type with
"phys_addr_t" type for the base address in ulite_assign() argument list.
Fixes: 8fa7b6100693 ("[POWERPC] Uartlite: Separate the bus binding from the driver proper") Signed-off-by: Lizhi Hou <lizhi.hou@xilinx.com> Link: https://lore.kernel.org/r/20211129202302.1319033-1-lizhi.hou@xilinx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In radeon_driver_open_kms(), radeon_vm_bo_add() is assigned to
vm->ib_bo_va and passes and used in radeon_vm_bo_set_addr(). In
radeon_vm_bo_set_addr(), there is a dereference of vm->ib_bo_va,
which could lead to a NULL pointer dereference on failure of
radeon_vm_bo_add().
Fix this bug by adding a check of vm->ib_bo_va.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_RADEON=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: cc9e67e3d700 ("drm/radeon: fix VM IB handling") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In amdgpu_connector_lcd_native_mode(), the return value of
drm_mode_duplicate() is assigned to mode, and there is a dereference
of it in amdgpu_connector_lcd_native_mode(), which will lead to a NULL
pointer dereference on failure of drm_mode_duplicate().
Fix this bug add a check of mode.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_AMDGPU=m show no new warnings, and
our static analyzer no longer warns about this code.
Change sdhcN aliases to mmcN to make them actually work. Currently the
board uses non-standard aliases sdhcN, which do not work, resulting in
mmc0 and mmc1 hosts randomly changing indices between boots.
This makes 'bridge-nf-filter-pppoe-tagged' sysctl work for
bridged traffic.
Looking at the original commit it doesn't appear this ever worked:
static unsigned int br_nf_post_routing(unsigned int hook, struct sk_buff **pskb,
[..]
if (skb->protocol == htons(ETH_P_8021Q)) {
skb_pull(skb, VLAN_HLEN);
skb->network_header += VLAN_HLEN;
+ } else if (skb->protocol == htons(ETH_P_PPP_SES)) {
+ skb_pull(skb, PPPOE_SES_HLEN);
+ skb->network_header += PPPOE_SES_HLEN;
}
[..]
NF_HOOK(... POST_ROUTING, ...)
... but the adjusted offsets are never restored.
The alternative would be to rip this code out for good,
but otoh we'd have to keep this anyway for the vlan handling
(which works because vlan tag info is in the skb, not the packet
payload).
The func v4l2_m2m_ctx_release waits for currently running jobs
to finish and then stop streaming both queues and frees the buffers.
All this should be done before the call to mtk_vcodec_enc_release
which frees the encoder handler. This fixes null-pointer dereference bug:
hsfreqrange should be chosen based on the calculated mbps which
is closer to the default bit rate and within the range as per
table[1]. But current calculation always selects first value which
is greater than or equal to the calculated mbps which may lead
to chosing a wrong range in some cases.
For example for 360 mbps for H3/M3N
Existing logic selects
Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]
This hsfreqrange is out of range.
The logic is changed to get the default value which is closest to the
calculated value [1]
Calculated value 360Mbps : Default 350Mbps Range [320.625 -380.625 mpbs]
The driver wrongly assummed that tx_submit() will start the transfer,
which is not the case, now that the at_xdmac driver is fixed. tx_submit
is supposed to push the current transaction descriptor to a pending queue,
waiting for issue_pending to be called. issue_pending must start the
transfer, not tx_submit.
The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.
When dvb_register_device() in dvb_dmxdev_init() fails, dvb_dmxdev_init()
does not return a failure, and the memory pointed to by dvbdev or
dvr_dvbdev is invalid at this point. If they are used subsequently, it
will result in UFA or null-ptr-deref.
If dvb_register_device() in dvb_dmxdev_init() fails, fix the bug by making
dvb_dmxdev_init() return an error as well.
Link: https://lore.kernel.org/linux-media/20211015085741.1203283-1-wanghai38@huawei.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prior to this patch was teedev_close_context() calling tee_device_put()
before teedev_ctx_put() leading to teedev_ctx_release() accessing
ctx->teedev just after the reference counter was decreased on the
teedev. Fix this by calling teedev_ctx_put() before tee_device_put().
Fixes: 217e0250cccb ("tee: use reference counting for tee_context") Reviewed-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported slab-out-of-bounds read in hci_le_adv_report_evt(). The
problem was in missing validaion check.
We should check if data is not malicious and we can read next data block.
If we won't check ptr validness, code can read a way beyond skb->end and
it can cause problems, of course.
The absence of this binding appears to be harmless in Linux but it breaks
Ethernet support in mainline u-boot. So add the binding (which is present
in all other u-boot supported GXBB device-trees).
Fixes: fb72c03e0e32 ("ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211012052522.30873-3-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver, once it found a divider, tries to round it up by increasing
the least significant bit of the fractional part by one when the
round_up argument is set and there's a remainder.
However, since it increases the divider it will actually reduce the
clock rate below what we were asking for, leading to issues with
clk_set_min_rate() that will complain that our rounded clock rate is
below the minimum of the rate.
Since the dividers are fairly precise already, let's remove that part so
that we can have clk_set_min_rate() working.
This is effectively a revert of 9c95b32ca093 ("clk: bcm2835: add a round
up ability to the clock divisor").
Fixes: 9c95b32ca093 ("clk: bcm2835: add a round up ability to the clock divisor") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality Tested-by: Michael Stapelberg <michael@stapelberg.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-3-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
If cmtp_init_sockets() in cmtp_init() fails, cmtp_init() still returns
success. This will cause a kernel bug when accessing uncreated ctmp
related data when the module exits.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we fail to attach (e.g., because 1 of 2 dual-DSI controllers aren't
ready), we leave a dangling drm_panel reference to freed memory. Clean
that up on failure.
This problem exists since the driver's introduction, but is especially
relevant after refactored for dual-DSI variants.
Image there are 3 items in the local list (@list). In the first
traversal, A is not deleted from @list.
1) A->B->C
^
|
pos (leave)
In the second traversal, B is deleted from @list. Concurrently, A is
deleted from @list through shmem_evict_inode() since last reference
counter of inode is dropped by other thread. Then the @list is corrupted.
2) A->B->C
^ ^
| |
evict pos (drop)
We should make sure the inode is either on the global list or deleted from
any local list before iput().
Fixed by moving inodes back to global list before we put them.
[akpm@linux-foundation.org: coding style fixes]
Link: https://lkml.kernel.org/r/20211125064502.99983-1-ligang.bdlg@bytedance.com Fixes: 779750d20b93 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by: Gang Li <ligang.bdlg@bytedance.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work Reported-by: Sam Bingner <sam@bingner.com> Tested-by: Sam Bingner <sam@bingner.com> Tested-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a04 ("can: add driver for Softing card") Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org Cc: stable@vger.kernel.org # 2.6.38 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a problem where closing the tuner would leave it in a state
where it would not tune to any channel when reopened. This problem was
discovered as part of https://github.com/hselasky/webcamd/issues/16.
Since adap->id is 0 or 1, this bit-shift overflows, which is undefined
behavior. The driver still worked in practice as the overflow would in
most environments result in 0, which rendered the line a no-op. When
running the driver as part of webcamd however, the overflow could lead
to 0xff due to optimizations by the compiler, which would, in the end,
improperly shut down the tuner.
The bug is a regression introduced in the commit referenced below. The
present patch causes identical behavior to before that commit for
adap->id equal to 0 or 1. The driver does not contain support for
dib0700 devices with more adapters, assuming such even exist.
Tests have been performed with the Xbox One Digital TV Tuner on amd64.
Not all dib0700 devices are expected to be affected by the regression;
this code path is only taken by those with incorrect endpoint numbers.
Reading from the CMOS involves writing to the index register and then
reading from the data register. Therefore access to the CMOS has to be
serialized with rtc_lock. This invocation of CMOS_READ was not
serialized, which could cause trouble when other code is accessing CMOS
at the same time.
Use spin_lock_irq() like the rest of the function.
Nothing in kernel modifies the RTC_DM_BINARY bit, so there could be a
separate pair of spin_lock_irq() / spin_unlock_irq() before doing the
math.
"Stolen memory" is memory set aside for use by an Intel integrated GPU.
The intel_graphics_quirks() early quirk reserves this memory when it is
called for a GPU that appears in the intel_early_ids[] table of integrated
GPUs.
Previously intel_graphics_quirks() was marked as QFLAG_APPLY_ONCE, so it
was called only for the first Intel GPU found. If a discrete GPU happened
to be enumerated first, intel_graphics_quirks() was called for it but not
for any integrated GPU found later. Therefore, stolen memory for such an
integrated GPU was never reserved.
For example, this problem occurs in this Alderlake-P (integrated) + DG2
(discrete) topology where the DG2 is found first, but stolen memory is
associated with the integrated GPU:
Remove the QFLAG_APPLY_ONCE flag and call intel_graphics_quirks() for every
Intel GPU. Reserve stolen memory for the first GPU that appears in
intel_early_ids[].
[bhelgaas: commit log, add code comment, squash in
https://lore.kernel.org/r/20220118190558.2ququ4vdfjuahicm@ldmartin-desk2] Link: https://lore.kernel.org/r/20220114002843.2083382-1-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot detected a NULL pointer dereference of nfc_llcp_sock->dev pointer
(which is a 'struct nfc_dev *') with calls to llcp_sock_sendmsg() after
a failed llcp_sock_bind(). The message being sent is a SOCK_DGRAM.
KASAN report:
BUG: KASAN: null-ptr-deref in nfc_alloc_send_skb+0x2d/0xc0
Read of size 4 at addr 00000000000005c8 by task llcp_sock_nfc_a/899
The issue was visible only with multiple simultaneous calls to bind() and
sendmsg(), which resulted in most of the bind() calls to fail. The
bind() was failing on checking if there is available WKS/SDP/SAP
(respective bit in 'struct nfc_llcp_local' fields). When there was no
available WKS/SDP/SAP, the bind returned error but the sendmsg() to such
socket was able to trigger mentioned NULL pointer dereference of
nfc_llcp_sock->dev.
The code looks simply racy and currently it protects several paths
against race with checks for (!nfc_llcp_sock->local) which is NULL-ified
in error paths of bind(). The llcp_sock_sendmsg() did not have such
check but called function nfc_llcp_send_ui_frame() had, although not
protected with lock_sock().
Therefore the race could look like (same socket is used all the time):
CPU0 CPU1
==== ====
llcp_sock_bind()
- lock_sock()
- success
- release_sock()
- return 0
llcp_sock_sendmsg()
- lock_sock()
- release_sock()
llcp_sock_bind(), same socket
- lock_sock()
- error
- nfc_llcp_send_ui_frame()
- if (!llcp_sock->local)
- llcp_sock->local = NULL
- nfc_put_device(dev)
- dereference llcp_sock->dev
- release_sock()
- return -ERRNO
The nfc_llcp_send_ui_frame() checked llcp_sock->local outside of the
lock, which is racy and ineffective check. Instead, its caller
llcp_sock_sendmsg(), should perform the check inside lock_sock().
Reported-and-tested-by: syzbot+7f23bcddf626e0593a39@syzkaller.appspotmail.com Fixes: b874dec21d1c ("NFC: Implement LLCP connection less Tx path") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fuzzed image, SSA table may indicate that a data block belongs to
invalid node, which node ID is out-of-range (0, 1, 2 or max_nid), in
order to avoid migrating inconsistent data in such corrupted image,
let's do sanity check anyway before data block migration.
If we ever see a touch report with contact count data we initialize
several variables used to read the contact count in the pre-report
phase. These variables are never reset if we process a report which
doesn't contain a contact count, however. This can cause the pre-
report function to trigger a read of arbitrary memory (e.g. NULL
if we're lucky) and potentially crash the driver.
This commit restores resetting of the variables back to default
"none" values that were used prior to the commit mentioned
below.
AES hardware may internally re-classify a contact that it thought was
intentional as a palm. Intentional contacts are reported as "down" with
the confidence bit set. When this re-classification occurs, however, the
state transitions to "up" with the confidence bit cleared. This kind of
transition appears to be legal according to Microsoft docs, but we do
not handle it correctly. Because the confidence bit is clear, we don't
call `wacom_wac_finger_slot` and update userspace. This causes hung
touches that confuse userspace and interfere with pen arbitration.
This commit adds a special case to ignore the confidence flag if a contact
is reported as removed. This ensures we do not leave a hung touch if one
of these re-classification events occured. Ideally we'd have some way to
also let userspace know that the touch has been re-classified as a palm
and needs to be canceled, but that's not possible right now :)
Link: https://github.com/linuxwacom/input-wacom/issues/288 Fixes: 7fb0413baa7f (HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts) CC: stable@vger.kernel.org Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Ping Cheng <ping.cheng@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log