The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
When resetting the block, the reset line is being driven low and then
high, which means that the line in DTS should be annotated as "active
low". It will become important when wcd9335 driver will be converted
to gpiod API that respects declared line polarities.
The Trogdor Homestar DTSI adds additional GPIO52 pin to secondary I2S pins
("sec_mi2s_active") and configures it to "mi2s_1" function.
The Trogdor DTSI (which is included by Homestar) configures drive
strength and bias for all "sec_mi2s_active" pins, thus the intention was
to apply this configuration also to GPIO52 on Homestar.
Reported-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Fixes: be0416a3f917 ("arm64: dts: qcom: Add sc7180-trogdor-homestar") Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221020225135.31750-2-krzysztof.kozlowski@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled
mode during system suspend") uses read_poll_timeout_atomic() macro
in ti_sci_do_xfer() to wait for completion when the system is
suspending. The break condition of the macro is set to "true" which
will cause it break immediately when evaluated, likely before the
TISCI xfer is completed, and always return 0. We want to poll here
until "done_state == true".
1) Change the break condition of read_poll_timeout_atomic() to
the bool variable "done_state".
2) The read_poll_timeout_atomic() returns 0 if the break condition
is met or -ETIMEDOUT if not. Since our break condition has changed
to "done_state", we also don't have to check for "!done_state" when
evaluating the return value.
Fixes: b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled mode during system suspend") Signed-off-by: Georgi Vlaev <g-vlaev@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Link: https://lore.kernel.org/r/20221021185704.181316-1-g-vlaev@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The WLAN regulator uses 'gpios' property instead of 'gpio' to specify
regulator enable GPIO. While the former is also currently handled by
the Linux kernel regulator-fixed driver, the later is the correct one
per DT bindings. Update the DT to use the later.
The Avenger96 is populated with STM32MP157A DHCOR SoM, drop the
stm32mp15xc.dtsi which should only be included in DTs of devices
which are populated with STM32MP15xC/F SoC as the stm32mp15xc.dtsi
enables CRYP block not present in the STM32MP15xA/D SoC .
Fixes: 7e76f82acd9e1 ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drive strength macros defined for FSD platform is not reflecting actual
names and values as per HW UM. FSD SoC pinctrl has following four levels
of drive-strength and their corresponding values:
Level-1 <-> 0
Level-2 <-> 1
Level-4 <-> 2
Level-6 <-> 3
The commit 684dac402f21 ("arm64: dts: fsd: Add initial pinctrl support")
used drive strength macros defined for Exynos4 SoC family. For some IPs
the macros values of Exynos4 matched and worked well, but Exynos4 SoC
family drive-strength (names and values) is not exactly matching with
FSD SoC.
Fix the drive strength macros to reflect actual names and values given
in FSD HW UM.
MSM8916 was originally using the "qcom,q6v5-pil" compatible for the
MSS remoteproc. Later it was decided to use SoC-specific compatibles
instead, so "qcom,msm8916-mss-pil" is now the preferred compatible.
Commit 60a05ed059a0 ("arm64: dts: qcom: msm8916: Add MSM8916-specific
compatibles to SCM/MSS") updated the MSM8916 device tree to make use of
the new compatible but still kept the old "qcom,q6v5-pil" as fallback.
This is inconsistent with other SoCs and conflicts with the description
in the binding documentation (which says that only one compatible should
be present). Also, it has no functional advantage since older kernels
could not handle this DT anyway (e.g. "power-domains" in the MSS node is
only supported by kernels that also support "qcom,msm8916-mss-pil").
Make this consistent with other SoCs by using only the
"qcom,msm8916-mss-pil" compatible.
Fixes: 60a05ed059a0 ("arm64: dts: qcom: msm8916: Add MSM8916-specific compatibles to SCM/MSS") Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220718140344.1831731-2-stephan.gerhold@kernkonzept.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Adjust MSM8996 cpufreq tables according to tables in msm-3.18. Some of
the frequencies are not supported on speed bins other than 0. Also other
speed bins support intermediate topmost frequencies, not supported on
speed bin 0. Implement all these differencies.
Qualcomm MSM8996 Pro is a variant of MSM8996 with higher frequencies
supported both on CPU and GPU. There are other minor hardware
differencies in the CPU and GPU regulators and bus fabrics.
However this results in significant differences between 8996 and 8996
Pro CPU OPP tables. Judging from msm-3.18 there are only few common
frequencies supported by both msm8996 and msm8996pro. Rather than
hacking the tables for msm8996, split msm8996pro support into a separate
file. Later this would allow having additional customizations for the
CBF, CPR, retulators, etc.
[DB: dropped all non-CPU-OPP changes]
Fixes: 90173a954a22 ("arm64: dts: qcom: msm8996: Add CPU opps") Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
[DB: Realigned supported-hw to keep compat with current cpufreq driver] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220724140421.1933004-3-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
As serial communication requires a clock signal, the High Speed Serial
Communication Interfaces with FIFO (HSCIF) are clocked by a clock that
is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the HSCIF0 Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car V4H Hardware User's Manual rev. 0.54.
The checks for musb->xceiv and musb->xceiv->set_power duplicate those in
usb_phy_set_power(), so there is no need of them. Moreover, not calling
usb_phy_set_power() results in usb_phy_set_charger_current() not being
called, so current USB config max current is not propagated through USB
charger framework and charger drivers may try to draw more current than
allowed or possible.
Fix that by removing those extra checks and calling usb_phy_set_power()
directly.
The reset line is called PWRST#, annotated as "active low" in the
binding documentation, and is driven low and then high by the driver to
reset the chip. However in device tree for CI20 board it was incorrectly
marked as "active high". Fix it.
Because (as far as I know) the ci20.dts is always built in the kernel I
elected not to also add a quirk to gpiolib to force the polarity there.
Fixes: db49ca38579d ("net: davicom: dm9000: switch to using gpiod API") Reported-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cd3bc044af48 ("KEYS: encrypted: Instantiate key with
user-provided decrypted data") added key instantiation with user
provided decrypted data. The user data is hex-ascii-encoded but was
just memcpy'ed to the binary buffer. Fix this to use hex2bin instead.
Old keys created from user provided decrypted data saved with "keyctl
pipe" are still valid, however if the key is recreated from decrypted
data the old key must be converted to the correct format. This can be
done with a small shell script, e.g.:
However, NEWKEY is still broken: If for BROKENKEY 32 bytes were
specified, a brute force attacker knowing the key properties would only
need to try at most 2^(16*8) keys, as if the key was only 16 bytes long.
The security issue is a result of the combination of limiting the input
range to hex-ascii and using memcpy() instead of hex2bin(). It could
have been fixed either by allowing binary input or using hex2bin() (and
doubling the ascii input key length). This patch implements the latter.
The corresponding test for the Linux Test Project ltp has also been
fixed (see link below).
This is because in scatterwalk_copychunks(), we attempted to write to
a buffer (@sign) that was allocated in the stack (vmalloc area) by
crypt_message() and thus accessing its remaining 8 (x2) bytes ended up
crossing a page boundary.
To simply fix it, we could just pass @sign kmalloc'd from
crypt_message() and then we're done. Luckily, we don't seem to pass
any other vmalloc'd buffers in smb_rqst::rq_iov...
Instead, let's map the correct pages and offsets from vmalloc buffers
as well in cifs_sg_set_buf() and then avoiding such oopses.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can take more than one second to check each connector
when the system is resumed. So if you have, say, eight
connectors, it may take eight seconds for ucsi_resume() to
finish. That's a bit too much.
This will modify ucsi_resume() so that it schedules a work
where the interface is actually resumed instead of checking
the connectors directly. The connections will also be
checked in separate tasks which are queued for each connector
separately.
When a MAC address is not assigned to the VF, that portion of the message
sent to the VF is not set. The memory, however, is allocated from the
stack meaning that information may be leaked to the VM. Initialize the
message buffer to 0 so that no information is passed to the VM in this
case.
Fixes: 6ddbc4cf1f4d ("igb: Indicate failure on vf reset for empty mac address") Reported-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221212190031.3983342-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using an InterTech DMG-02 dongle, the led remains on when the system goes
into standby mode. After wakeup, it's no longer possible to control the
led.
It turned out that the register settings to enable or disable the led were
not correct. They worked for some dongles like the Edimax V2 but not for
others like the InterTech DMG-02.
This patch fixes the register settings. Bit 3 in the led_cfg2 register
controls the led status, bit 5 must always be set to be able to control
the led, bit 6 has no influence on the led. Setting the mac_pinmux_cfg
register is not necessary.
These settings were tested with Edimax V2 and InterTech DMG-02.
Cc: stable@vger.kernel.org Fixes: 8cd574e6af54 ("staging: r8188eu: introduce new hal dir for RTL8188eu driver") Suggested-by: Michael Straube <straube.linux@gmail.com> Signed-off-by: Martin Kaiser <martin@kaiser.cx> Tested-by: Michael Straube <straube.linux@gmail.com> # InterTech DMG-02, Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150 Link: https://lore.kernel.org/r/20221015151115.232095-2-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ADL-N systems have the same issue as ADL-P, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to ADL-N as well.
This patch depends on commit 34cd2db408d5 ("xhci: Add quirk to reset
host back to default state at shutdown").
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects ADL-N devices, and ADL-N support was added starting from v5.16.
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
Setup function uvc_function_setup permits control transfer
requests with up to 64 bytes of payload (UVC_MAX_REQUEST_SIZE),
data stage handler for OUT transfer uses memcpy to copy req->actual
bytes to uvc_event->data.data array of size 60. This may result
in an overflow of 4 bytes.
Fixes: cdda479f15cd ("USB gadget: video class function driver") Cc: stable <stable@kernel.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com> Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com> Link: https://lore.kernel.org/r/20221206141301.51305-1-szymon.heidrich@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extending file within last block it can happen that the extent is
already rounded to the blocksize and thus contains the offset we want to
grow up to. In such case we would mistakenly expand the last extent and
make it one block longer than it should be, exposing unallocated block
in a file and causing data corruption. Fix the problem by properly
detecting this case and bailing out.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When preallocation extent is the first one in the extent block, the
code would corrupt extent tree header instead. Fix the problem and use
udf_delete_aext() for deleting extent to avoid some code duplication.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extending file with a hole, we tried to preserve existing
preallocation for the file. However that is not very useful and
complicates code because the previous extent may need to be rounded to
block boundary as well (which we forgot to do thus causing data
corruption for sequence like:
parent is the interrupt parent, not the parent of node. Use
node->parent. This fixes endianness detection on big-endian platforms.
Fixes: 1b00adce8afd ("irqchip/ls-extirq: Fix invalid wait context by avoiding to use regmap") Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221201212807.616191-1-sean.anderson@seco.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_SLUB=y, following commit 6edf2576a6cc ("mm/slub: enable
debugging memory wasting of kmalloc") mt7621 failed to boot very early,
without showing any console messages.
This exposed the pre-existing bug of mt7621.c using kzalloc before normal
memory management was available.
Prior to this slub change, there existed the unintended protection against
"kmem_cache *s" being NULL as slab_pre_alloc_hook() happened to
return NULL and bailed out of slab_alloc_node().
This allowed mt7621 prom_soc_init to fail in the soc_dev_init kzalloc,
but continue booting without the SOC_BUS driver device registered.
Console output from a DEBUG_ZBOOT vmlinuz kernel loading,
with mm/slub modified to warn on kmem_cache zero or null:
zimage at: 80B842A0810B4BC0
Uncompressing Linux at load address 80001000
Copy device tree to address 80B80EE0
Now, booting the kernel...
Allowing soc_device_register to work exposed oops in the mt7621 phy pci,
and pci controller drivers from soc_device_match_attr, due to missing
sentinels in the quirks tables. These were fixed with:
commit 819b885cd886 ("phy: ralink: mt7621-pci: add sentinel to quirks
table")
not yet applied ("PCI: mt7621: add sentinel to quirks table")
Current driver is missing a sentinel in the struct soc_device_attribute
array, which causes an oops when assessed by the
soc_device_match(mt7621_pcie_quirks_match) call.
This was only exposed once the CONFIG_SOC_MT7621 mt7621 soc_dev_attr
was fixed to register the SOC as a device, in:
commit 7c18b64bba3b ("mips: ralink: mt7621: do not use kzalloc too early")
GCC 11.3.0 fails to compile btf_dump.c due to the following error,
which seems to originate in btf_dump_struct_data where the returned
value would be uninitialized if btf_vlen returns zero.
btf_dump.c: In function ‘btf_dump_dump_type_data’:
btf_dump.c:2363:12: error: ‘err’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2363 | if (err < 0)
| ^
Fixes: 920d16af9b42 ("libbpf: BTF dumper support for typed data") Signed-off-by: David Michael <fedora.dm0@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Stanislav Fomichev <sdf@google.com> Acked-by: Alan Maguire <alan.maguire@oracle.com> Link: https://lore.kernel.org/bpf/87zgcu60hq.fsf@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, ld.lld moved from '--undefined-version' to
'--no-undefined-version' as the default, which breaks building the vDSO
when CONFIG_X86_SGX is not set:
ld.lld: error: version script assignment of 'LINUX_2.6' to symbol '__vdso_sgx_enter_enclave' failed: symbol not defined
__vdso_sgx_enter_enclave is only included in the vDSO when
CONFIG_X86_SGX is set. Only export it if it will be present in the final
object, which clears up the error.
Linus Torvalds [Sun, 11 Dec 2022 01:10:52 +0000 (17:10 -0800)]
Merge tag 'mm-hotfixes-stable-2022-12-10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Nine hotfixes.
Six for MM, three for other areas. Four of these patches address
post-6.0 issues"
* tag 'mm-hotfixes-stable-2022-12-10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
memcg: fix possible use-after-free in memcg_write_event_control()
MAINTAINERS: update Muchun Song's email
mm/gup: fix gup_pud_range() for dax
mmap: fix do_brk_flags() modifying obviously incorrect VMAs
mm/swap: fix SWP_PFN_BITS with CONFIG_PHYS_ADDR_T_64BIT on 32bit
tmpfs: fix data loss from failed fallocate
kselftests: cgroup: update kmem test precision tolerance
mm: do not BUG_ON missing brk mapping, because userspace can unmap it
mailmap: update Matti Vaittinen's email address
Tejun Heo [Thu, 8 Dec 2022 02:53:15 +0000 (16:53 -1000)]
memcg: fix possible use-after-free in memcg_write_event_control()
memcg_write_event_control() accesses the dentry->d_name of the specified
control fd to route the write call. As a cgroup interface file can't be
renamed, it's safe to access d_name as long as the specified file is a
regular cgroup file. Also, as these cgroup interface files can't be
removed before the directory, it's safe to access the parent too.
Prior to 347c4a874710 ("memcg: remove cgroup_event->cft"), there was a
call to __file_cft() which verified that the specified file is a regular
cgroupfs file before further accesses. The cftype pointer returned from
__file_cft() was no longer necessary and the commit inadvertently dropped
the file type check with it allowing any file to slip through. With the
invarients broken, the d_name and parent accesses can now race against
renames and removals of arbitrary files and cause use-after-free's.
Fix the bug by resurrecting the file type check in __file_cft(). Now that
cgroupfs is implemented through kernfs, checking the file operations needs
to go through a layer of indirection. Instead, let's check the superblock
and dentry type.
Link: https://lkml.kernel.org/r/Y5FRm/cfcKPGzWwl@slm.duckdns.org Fixes: 347c4a874710 ("memcg: remove cgroup_event->cft") Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Jann Horn <jannh@google.com> Acked-by: Roman Gushchin <roman.gushchin@linux.dev> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> [3.14+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
John Starks [Wed, 7 Dec 2022 06:00:53 +0000 (22:00 -0800)]
mm/gup: fix gup_pud_range() for dax
For dax pud, pud_huge() returns true on x86. So the function works as long
as hugetlb is configured. However, dax doesn't depend on hugetlb.
Commit 414fd080d125 ("mm/gup: fix gup_pmd_range() for dax") fixed
devmap-backed huge PMDs, but missed devmap-backed huge PUDs. Fix this as
well.
Add more sanity checks to the VMA that do_brk_flags() will expand. Ensure
the VMA matches basic merge requirements within the function before
calling can_vma_merge_after().
Drop the duplicate checks from vm_brk_flags() since they will be enforced
later.
The old code would expand file VMAs on brk(), which is functionally
wrong and also dangerous in terms of locking because the brk() path
isn't designed for file VMAs and therefore doesn't lock the file
mapping. Checking can_vma_merge_after() ensures that new anonymous
VMAs can't be merged into file VMAs.
See https://lore.kernel.org/linux-mm/CAG48ez1tJZTOjS_FjRZhvtDA-STFmdw8PEizPDwMGFd_ui0Nrw@mail.gmail.com/
Link: https://lkml.kernel.org/r/20221205192304.1957418-1-Liam.Howlett@oracle.com Fixes: 2e7ce7d354f2 ("mm/mmap: change do_brk_flags() to expand existing VMA and add do_brk_munmap()") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Suggested-by: Jann Horn <jannh@google.com> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: SeongJae Park <sj@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
David Hildenbrand [Mon, 5 Dec 2022 15:08:57 +0000 (16:08 +0100)]
mm/swap: fix SWP_PFN_BITS with CONFIG_PHYS_ADDR_T_64BIT on 32bit
We use "unsigned long" to store a PFN in the kernel and phys_addr_t to
store a physical address.
On a 64bit system, both are 64bit wide. However, on a 32bit system, the
latter might be 64bit wide. This is, for example, the case on x86 with
PAE: phys_addr_t and PTEs are 64bit wide, while "unsigned long" only spans
32bit.
The current definition of SWP_PFN_BITS without MAX_PHYSMEM_BITS misses
that case, and assumes that the maximum PFN is limited by an 32bit
phys_addr_t. This implies, that SWP_PFN_BITS will currently only be able
to cover 4 GiB - 1 on any 32bit system with 4k page size, which is wrong.
Let's rely on the number of bits in phys_addr_t instead, but make sure to
not exceed the maximum swap offset, to not make the BUILD_BUG_ON() in
is_pfn_swap_entry() unhappy. Note that swp_entry_t is effectively an
unsigned long and the maximum swap offset shares that value with the swap
type.
For example, on an 8 GiB x86 PAE system with a kernel config based on
Debian 11.5 (-> CONFIG_FLATMEM=y, CONFIG_X86_PAE=y), we will currently
fail removing migration entries (remove_migration_ptes()), because
mm/page_vma_mapped.c:check_pte() will fail to identify a PFN match as
swp_offset_pfn() wrongly masks off PFN bits. For example,
split_huge_page_to_list()->...->remap_page() will leave migration entries
in place and continue to unlock the page.
Later, when we stumble over these migration entries (e.g., via
/proc/self/pagemap), pfn_swap_entry_to_page() will BUG_ON() because these
migration entries shouldn't exist anymore and the page was unlocked.
Hugh Dickins [Mon, 5 Dec 2022 00:51:50 +0000 (16:51 -0800)]
tmpfs: fix data loss from failed fallocate
Fix tmpfs data loss when the fallocate system call is interrupted by a
signal, or fails for some other reason. The partial folio handling in
shmem_undo_range() forgot to consider this unfalloc case, and was liable
to erase or truncate out data which had already been committed earlier.
It turns out that none of the partial folio handling there is appropriate
for the unfalloc case, which just wants to proceed to removal of whole
folios: which find_get_entries() provides, even when partially covered.
Michal Hocko [Fri, 2 Dec 2022 08:50:26 +0000 (09:50 +0100)]
kselftests: cgroup: update kmem test precision tolerance
1813e51eece0 ("memcg: increase MEMCG_CHARGE_BATCH to 64") has changed
the batch size while this test case has been left behind. This has led
to a test failure reported by test bot:
not ok 2 selftests: cgroup: test_kmem # exit=1
Update the tolerance for the pcp charges to reflect the
MEMCG_CHARGE_BATCH change to fix this.
[akpm@linux-foundation.org: update comments, per Roman] Link: https://lkml.kernel.org/r/Y4m8Unt6FhWKC6IH@dhcp22.suse.cz Fixes: 1813e51eece0a ("memcg: increase MEMCG_CHARGE_BATCH to 64") Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: kernel test robot <yujie.liu@intel.com> Link: https://lore.kernel.org/oe-lkp/202212010958.c1053bd3-yujie.liu@intel.com Acked-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <roman.gushchin@linux.dev> Tested-by: Yujie Liu <yujie.liu@intel.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "Michal Koutný" <mkoutny@suse.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Linus Torvalds [Fri, 9 Dec 2022 18:45:51 +0000 (10:45 -0800)]
Merge tag 'media/v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A v4l-core fix related to validating DV timings related to video
blanking values"
* tag 'media/v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: v4l2-dv-timings.c: fix too strict blanking sanity checks
Linus Torvalds [Fri, 9 Dec 2022 00:58:31 +0000 (16:58 -0800)]
Merge tag 'drm-fixes-2022-12-09' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Last set of fixes for final, scattered bunch of fixes, two amdgpu, one
vmwgfx, and some misc others.
amdgpu:
- S0ix fix
- DCN 3.2 array out of bounds fix
shmem:
- Fixes to shmem-helper error paths
bridge:
- Fix polarity bug in bridge/ti-sn65dsi86
dw-hdmi:
- Prefer 8-bit RGB fallback before any YUV mode in dw-hdmi, since
some panels lie about YUV support
vmwgfx:
- Stop using screen objects when SEV is active"
* tag 'drm-fixes-2022-12-09' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: fix array index out of bound error in DCN32 DML
drm/amdgpu/sdma_v4_0: turn off SDMA ring buffer in the s2idle suspend
drm/vmwgfx: Don't use screen objects when SEV is active
drm/shmem-helper: Avoid vm_open error paths
drm/shmem-helper: Remove errant put in error path
drm: bridge: dw_hdmi: fix preference of RGB modes over YUV420
drm/bridge: ti-sn65dsi86: Fix output polarity setting bug
drm/vmwgfx: Fix race issue calling pin_user_pages
Dave Airlie [Fri, 9 Dec 2022 00:11:05 +0000 (10:11 +1000)]
Merge tag 'drm-misc-fixes-2022-12-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v6.1 final?:
- Fix polarity bug in bridge/ti-sn65dsi86.
- Prefer 8-bit RGB fallback before any YUV mode in dw-hdmi, since some
panels lie about YUV support.
- Fixes to shmem-helper error paths.
- Small vmwgfx to stop using screen objects when SEV is active.
Linus Torvalds [Thu, 8 Dec 2022 23:32:13 +0000 (15:32 -0800)]
Merge tag 'net-6.1-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, can and netfilter.
Current release - new code bugs:
- bonding: ipv6: correct address used in Neighbour Advertisement
parsing (src vs dst typo)
- fec: properly scope IRQ coalesce setup during link up to supported
chips only
Previous releases - regressions:
- Bluetooth fixes for fake CSR clones (knockoffs):
- re-add ERR_DATA_REPORTING quirk
- fix crash when device is replugged
- Bluetooth:
- silence a user-triggerable dmesg error message
- L2CAP: fix u8 overflow, oob access
- correct vendor codec definition
- fix support for Read Local Supported Codecs V2
- ti: am65-cpsw: fix RGMII configuration at SPEED_10
- mana: fix race on per-CQ variable NAPI work_done
Previous releases - always broken:
- af_unix: diag: fetch user_ns from in_skb in unix_diag_get_exact(),
avoid null-deref
- af_can: fix NULL pointer dereference in can_rcv_filter
- can: slcan: fix UAF with a freed work
- can: can327: flush TX_work on ldisc .close()
- macsec: add missing attribute validation for offload
- ipv6: avoid use-after-free in ip6_fragment()
- nft_set_pipapo: actually validate intervals in fields after the
first one
- mvneta: prevent oob access in mvneta_config_rss()
- ipv4: fix incorrect route flushing when table ID 0 is used, or when
source address is deleted
- phy: mxl-gpy: add workaround for IRQ bug on GPY215B and GPY215C"
* tag 'net-6.1-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
s390/qeth: fix use-after-free in hsci
macsec: add missing attribute validation for offload
net: mvneta: Fix an out of bounds check
net: thunderbolt: fix memory leak in tbnet_open()
ipv6: avoid use-after-free in ip6_fragment()
net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
net: phy: mxl-gpy: add MDINT workaround
net: dsa: mv88e6xxx: accept phy-mode = "internal" for internal PHY ports
xen/netback: don't call kfree_skb() under spin_lock_irqsave()
dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove()
ethernet: aeroflex: fix potential skb leak in greth_init_rings()
tipc: call tipc_lxc_xmit without holding node_read_lock
can: esd_usb: Allow REC and TEC to return to zero
can: can327: flush TX_work on ldisc .close()
can: slcan: fix freed work crash
can: af_can: fix NULL pointer dereference in can_rcv_filter
net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()
ipv4: Fix incorrect route flushing when table ID 0 is used
ipv4: Fix incorrect route flushing when source address is deleted
...
Linus Torvalds [Thu, 8 Dec 2022 20:37:42 +0000 (12:37 -0800)]
Merge tag 'for-linus-2022120801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
"A regression fix for handling Logitech HID++ devices and memory
corruption fixes:
- regression fix (revert) for catch-all handling of Logitech HID++
Bluetooth devices; there are devices that turn out not to work with
this, and the root cause is yet to be properly understood. So we
are dropping it for now, and it will be revisited for 6.2 or 6.3
(Benjamin Tissoires)
- memory corruption fix in HID core (ZhangPeng)
- memory corruption fix in hid-lg4ff (Anastasia Belova)
- Kconfig fix for I2C_HID (Benjamin Tissoires)
- a few device-id specific quirks that piggy-back on top of the
important fixes above"
* tag 'for-linus-2022120801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Revert "HID: logitech-hidpp: Enable HID++ for all the Logitech Bluetooth devices"
Revert "HID: logitech-hidpp: Remove special-casing of Bluetooth devices"
HID: usbhid: Add ALWAYS_POLL quirk for some mice
HID: core: fix shift-out-of-bounds in hid_report_raw_event
HID: uclogic: Add HID_QUIRK_HIDINPUT_FORCE quirk
HID: fix I2C_HID not selected when I2C_HID_OF_ELAN is
HID: hid-lg4ff: Add check for empty lbuf
HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10
HID: uclogic: Fix frame templates for big endian architectures
As reported in [0], hid-logitech-hidpp now binds on all bluetooth mice,
but there are corner cases where hid-logitech-hidpp just gives up on
the mouse. This leads the end user with a dead mouse.
Given that we are at -rc8, we are definitively too late to find a proper
fix. We already identified 2 issues less than 24 hours after the bug
report. One in that ->match() was never designed to be used anywhere else
than in hid-generic, and the other that hid-logitech-hidpp has corner
cases where it gives up on devices it is not supposed to.
So we have no choice but postpone this patch to the next kernel release.
We need to revert commit 532223c8ac57 ("HID: logitech-hidpp: Enable HID++
for all the Logitech Bluetooth devices") because that commit might make
hid-logitech-hidpp bind on mice that are not well enough supported by
hid-logitech-hidpp, and the end result is that the probe of those mice
is now returning -ENODEV, leaving the end user with a dead mouse.
Given that commit 8544c812e43a ("HID: logitech-hidpp: Remove special-casing
of Bluetooth devices") is a direct dependency of 532223c8ac57, revert it
too.
Note that this also adapt according to commit 908d325e1665 ("HID:
logitech-hidpp: Detect hi-res scrolling support") to re-add support of
the devices that were removed from that commit too.
I have locally an MX Master and I tested this device with that revert,
ensuring we still have high-res scrolling.
Reported-by: Rafael J . Wysocki <rjw@rjwysocki.net> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Thu, 8 Dec 2022 19:16:15 +0000 (11:16 -0800)]
Merge tag 'loongarch-fixes-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Export smp_send_reschedule() for modules use, fix a huge page entry
update issue, and add documents for booting description"
* tag 'loongarch-fixes-6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
docs/zh_CN: Add LoongArch booting description's translation
docs/LoongArch: Add booting description
LoongArch: mm: Fix huge page entry update for virtual machine
LoongArch: Export symbol for function smp_send_reschedule()
Linus Torvalds [Thu, 8 Dec 2022 18:46:52 +0000 (10:46 -0800)]
Merge tag 'ata-6.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fix from Damien Le Moal:
- Avoid a NULL pointer dereference in the libahci platform code that
can happen on initialization when a device tree does not specify
names for the adapter clocks (from Anders)
* tag 'ata-6.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libahci_platform: ahci_platform_find_clk: oops, NULL pointer
Tejun Heo [Thu, 8 Dec 2022 02:53:15 +0000 (16:53 -1000)]
memcg: Fix possible use-after-free in memcg_write_event_control()
memcg_write_event_control() accesses the dentry->d_name of the specified
control fd to route the write call. As a cgroup interface file can't be
renamed, it's safe to access d_name as long as the specified file is a
regular cgroup file. Also, as these cgroup interface files can't be
removed before the directory, it's safe to access the parent too.
Prior to 347c4a874710 ("memcg: remove cgroup_event->cft"), there was a
call to __file_cft() which verified that the specified file is a regular
cgroupfs file before further accesses. The cftype pointer returned from
__file_cft() was no longer necessary and the commit inadvertently
dropped the file type check with it allowing any file to slip through.
With the invarients broken, the d_name and parent accesses can now race
against renames and removals of arbitrary files and cause
use-after-free's.
Fix the bug by resurrecting the file type check in __file_cft(). Now
that cgroupfs is implemented through kernfs, checking the file
operations needs to go through a layer of indirection. Instead, let's
check the superblock and dentry type.
Radu Nicolae Pirea (OSS) [Wed, 7 Dec 2022 13:23:47 +0000 (15:23 +0200)]
net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f2287 ("net: dsa: sja1105: configure the multicast policers, if present") CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Emeel Hakim [Wed, 7 Dec 2022 10:16:18 +0000 (12:16 +0200)]
macsec: add missing attribute validation for offload
Add missing attribute validation for IFLA_MACSEC_OFFLOAD
to the netlink policy.
Fixes: 791bb3fcafce ("net: macsec: add support for specifying offload upon link creation") Signed-off-by: Emeel Hakim <ehakim@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Link: https://lore.kernel.org/r/20221207101618.989-1-ehakim@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Wed, 7 Dec 2022 07:06:31 +0000 (10:06 +0300)]
net: mvneta: Fix an out of bounds check
In an earlier commit, I added a bounds check to prevent an out of bounds
read and a WARN(). On further discussion and consideration that check
was probably too aggressive. Instead of returning -EINVAL, a better fix
would be to just prevent the out of bounds read but continue the process.
Background: The value of "pp->rxq_def" is a number between 0-7 by default,
or even higher depending on the value of "rxq_number", which is a module
parameter. If the value is more than the number of available CPUs then
it will trigger the WARN() in cpu_max_bits_warn().
Fixes: e8b4fc13900b ("net: mvneta: Prevent out of bounds read in mvneta_config_rss()") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/Y5A7d1E5ccwHTYPf@kadam Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 7 Dec 2022 01:50:01 +0000 (09:50 +0800)]
net: thunderbolt: fix memory leak in tbnet_open()
When tb_ring_alloc_rx() failed in tbnet_open(), ida that allocated in
tb_xdomain_alloc_out_hopid() is not released. Add
tb_xdomain_release_out_hopid() to the error path to release ida.
Fixes: 180b0689425c ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20221207015001.1755826-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It introduced a boot regression on colibri-imx7, and potentially any
other i.MX7 boards with MTD partition list generated into the fdt by
U-Boot.
While the commit we are reverting here is not obviously wrong, it fixes
only a dt binding checker warning that is non-functional, while it
introduces a boot regression and there is no obvious fix ready.
Huacai Chen [Thu, 8 Dec 2022 06:59:15 +0000 (14:59 +0800)]
LoongArch: mm: Fix huge page entry update for virtual machine
In virtual machine (guest mode), the tlbwr instruction can not write the
last entry of MTLB, so we need to make it non-present by invtlb and then
write it by tlbfill. This also simplify the whole logic.
Signed-off-by: Rui Wang <wangrui@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Bibo Mao [Thu, 8 Dec 2022 06:59:15 +0000 (14:59 +0800)]
LoongArch: Export symbol for function smp_send_reschedule()
Function smp_send_reschedule() is standard kernel API, which is defined
in header file include/linux/smp.h. However, on LoongArch it is defined
as an inline function, this is confusing and kernel modules can not use
this function.
Now we define smp_send_reschedule() as a general function, and add a
EXPORT_SYMBOL_GPL on this function, so that kernel modules can use it.
Signed-off-by: Bibo Mao <maobibo@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Eric Dumazet [Tue, 6 Dec 2022 10:13:51 +0000 (10:13 +0000)]
ipv6: avoid use-after-free in ip6_fragment()
Blamed commit claimed rcu_read_lock() was held by ip6_fragment() callers.
It seems to not be always true, at least for UDP stack.
syzbot reported:
BUG: KASAN: use-after-free in ip6_dst_idev include/net/ip6_fib.h:245 [inline]
BUG: KASAN: use-after-free in ip6_fragment+0x2724/0x2770 net/ipv6/ip6_output.c:951
Read of size 8 at addr ffff88801d403e80 by task syz-executor.3/7618
The buggy address belongs to the object at ffff88801d403dc0
which belongs to the cache ip6_dst_cache of size 240
The buggy address is located 192 bytes inside of
240-byte region [ffff88801d403dc0, ffff88801d403eb0)
Fixes: 1758fd4688eb ("ipv6: remove unnecessary dst_hold() in ip6_fragment()") Reported-by: syzbot+8c0ac31aa9681abb9e2d@syzkaller.appspotmail.com Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/r/20221206101351.2037285-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yang Yingliang [Wed, 7 Dec 2022 01:53:10 +0000 (09:53 +0800)]
net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()
It is not allowed to call kfree_skb() or consume_skb() from
hardware interrupt context or with interrupts being disabled.
So replace kfree_skb/dev_kfree_skb() with dev_kfree_skb_irq()
and dev_consume_skb_irq() under spin_lock_irq().
projects / users / jedix / linux-maple.git / log