The default error code in pfkey_msg2xfrm_state() is -ENOBUFS. We
added a new call to security_xfrm_state_alloc() which sets "err" to zero
so there several places where we can return ERR_PTR(0) if kmalloc()
fails. The caller is expecting error pointers so it leads to a NULL
dereference.
Fixes: df71837d5024 ("[LSM-IPSec]: Security association restriction.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_XFRM_SUB_POLICY=y, xfrm_dst stores a copy of the flowi for
that dst. Unfortunately, the code that allocates and fills this copy
doesn't care about what type of flowi (flowi, flowi4, flowi6) gets
passed. In multiple code paths (from raw_sendmsg, from TCP when
replying to a FIN, in vxlan, geneve, and gre), the flowi that gets
passed to xfrm is actually an on-stack flowi4, so we end up reading
stuff from the stack past the end of the flowi4 struct.
Since xfrm_dst->origin isn't used anywhere following commit ca116922afa8 ("xfrm: Eliminate "fl" and "pol" args to
xfrm_bundle_ok()."), just get rid of it. xfrm_dst->partner isn't used
either, so get rid of that too.
Fixes: 9d6ec938019c ("ipv4: Use flowi4 in public route lookup interfaces.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing code that uses vmalloc_to_page() may assume that any address
for which is_vmalloc_addr() returns true may be passed into
vmalloc_to_page() to retrieve the associated struct page.
This is not un unreasonable assumption to make, but on architectures
that have CONFIG_HAVE_ARCH_HUGE_VMAP=y, it no longer holds, and we need
to ensure that vmalloc_to_page() does not go off into the weeds trying
to dereference huge PUDs or PMDs as table entries.
Given that vmalloc() and vmap() themselves never create huge mappings or
deal with compound pages at all, there is no correct answer in this
case, so return NULL instead, and issue a warning.
When reading /proc/kcore on arm64, you will hit an oops as soon as you
hit the huge mappings used for the various segments that make up the
mapping of vmlinux. With this patch applied, you will no longer hit the
oops, but the kcore contents willl be incorrect (these regions will be
zeroed out)
We are fixing this for kcore specifically, so it avoids vread() for
those regions. At least one other problematic user exists, i.e.,
/dev/kmem, but that is currently broken on arm64 for other reasons.
Link: http://lkml.kernel.org/r/20170609082226.26152-1-ard.biesheuvel@linaro.org Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Laura Abbott <labbott@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: zhong jiang <zhongjiang@huawei.com> Cc: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ardb: non-trivial backport to v4.9] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a47b70ea86bd ("ravb: unmap descriptors when freeing rings") has
introduced the issue seen in [1] reproduced on H3ULCB board.
Fix this by relocating the RX skb ringbuffer free operation, so that
swiotlb page unmapping can be done first. Freeing of aligned TX buffers
is not relevant to the issue seen in [1]. Still, reposition TX free
calls as well, to have all kfree() operations performed consistently
_after_ dma_unmap_*()/dma_free_*().
[1] Console screenshot with the problem reproduced:
salvator-x login: root
root@salvator-x:~# ifconfig eth0 up
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: \
attached PHY driver [Micrel KSZ9031 Gigabit PHY] \
(mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=235)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
root@salvator-x:~#
root@salvator-x:~# ifconfig eth0 down
==================================================================
BUG: KASAN: use-after-free in swiotlb_tbl_unmap_single+0xc4/0x35c
Write of size 1538 at addr ffff8006d884f780 by task ifconfig/1649
This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661
1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.
2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.
Commit 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.
Fixes: 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class is non-0") Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6f29a1306131 ("sctp: sctp_addr_id2transport should verify the
addr before looking up assoc") invoked sctp_verify_addr to verify the
addr.
But it didn't check af variable beforehand, once users pass an address
with family = 0 through sockopt, sctp_get_af_specific will return NULL
and NULL pointer dereference will be caused by af->sockaddr_len.
This patch is to fix it by returning NULL if af variable is NULL.
Fixes: 6f29a1306131 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes: acba2420f9d2 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs") Fixes: e0debf9cb50d ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, we allocate memory always with GFP_ATOMIC flag.
When the system is under memory pressure and a user tries to send,
the send fails due to low memory. However, the user application
can wait for free memory if we allocate it using GFP_KERNEL flag.
In this commit, we use allocate memory with GFP_KERNEL for all user
allocation.
Reported-by: Rune Torgersen <runet@innovsys.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to show correct locations for events on modules by relocating given
address instead of retrying after failure.
This happens when the module text size is big enough, bigger than
sh_addr, because the original code retries with given address + sh_addr
if it failed to find CU DIE at the given address.
Any address smaller than sh_addr always fails and it retries with the
correct address, but addresses bigger than sh_addr will get a CU DIE
which is on the given address (not adjusted by sh_addr).
In my environment(x86-64), the sh_addr of ".text" section is 0x10030.
Since i915 is a huge kernel module, we can see this issue as below.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | sort | head -n1 ffffffffc0270000 t i915_switcheroo_can_switch [i915]
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | grep -B1 ^ffffffffc028\
| head -n 2 ffffffffc027ff80 t haswell_init_clock_gating [i915] ffffffffc0280110 t valleyview_init_clock_gating [i915]
So setup probes on both function and see what happen.
$ sudo ./perf probe -m i915 -a haswell_init_clock_gating \
-a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on i915_vga_set_decode:4@gpu/drm/i915/i915_drv.c in i915)
As you can see, haswell_init_clock_gating is correctly shown,
but valleyview_init_clock_gating is not.
With this patch, both events are shown correctly.
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
Committer notes:
In my case:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on i915_getparam+432@gpu/drm/i915/i915_drv.c in i915)
probe:valleyview_init_clock_gating (on __i915_printk+240@gpu/drm/i915/i915_drv.c in i915)
#
# readelf -SW /lib/modules/4.9.0+/build/vmlinux | egrep -w '.text|Name'
[Nr] Name Type Address Off Size ES Flg Lk Inf Al
[ 1] .text PROGBITS ffffffff81000000 200000 822fd3 00 AX 0 0 4096
#
So both are b0rked, now with the fix:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
#
Both looks correct.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/148411436777.9978.1440275861947194930.stgit@devbox Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Ivan Vecera <cera@cera.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Ivan Vecera <cera@cera.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.
We have quite a lot of code that depends on the order of the
__ctl_load inline assemby and subsequent memory accesses, like
e.g. disabling lowcore protection and the writing to lowcore.
Since the __ctl_load macro does not have memory barrier semantics, nor
any other dependencies the compiler is, theoretically, free to shuffle
code around. Or in other words: storing to lowcore could happen before
lowcore protection is disabled.
In order to avoid this class of potential bugs simply add a full
memory barrier to the __ctl_load macro.
If the last section of a core file ends with an unmapped or zero page,
the size of the file does not correspond with the last dump_skip() call.
gdb complains that the file is truncated and can be confusing to users.
After all of the vma sections are written, make sure that the file size
is no smaller than the current file position.
This problem can be demonstrated with gdb's bigcore testcase on the
sparc architecture.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is problem with installing an event in a task that is 'stuck' on
an offline CPU.
Blocked tasks are not dis-assosciated from offlined CPUs, after all, a
blocked task doesn't run and doesn't require a CPU etc.. Only on
wakeup do we ammend the situation and place the task on a available
CPU.
If we hit such a task with perf_install_in_context() we'll loop until
either that task wakes up or the CPU comes back online, if the task
waking depends on the event being installed, we're stuck.
While looking into this issue, I also spotted another problem, if we
hit a task with perf_install_in_context() that is in the middle of
being migrated, that is we observe the old CPU before sending the IPI,
but run the IPI (on the old CPU) while the task is already running on
the new CPU, things also go sideways.
Rework things to rely on task_curr() -- outside of rq->lock -- which
is rather tricky. Imagine the following scenario where we're trying to
install the first event into our task 't':
CPU0 CPU1 CPU2
(current == t)
t->perf_event_ctxp[] = ctx;
smp_mb();
cpu = task_cpu(t);
switch(t, n);
migrate(t, 2);
switch(p, t);
ctx = t->perf_event_ctxp[]; // must not be NULL
smp_function_call(cpu, ..);
generic_exec_single()
func();
spin_lock(ctx->lock);
if (task_curr(t)) // false
add_event_to_ctx();
spin_unlock(ctx->lock);
perf_event_context_sched_in();
spin_lock(ctx->lock);
// sees event
So its CPU0's store of t->perf_event_ctxp[] that must not go 'missing'.
Because if CPU2's load of that variable were to observe NULL, it would
not try to schedule the ctx and we'd have a task running without its
counter, which would be 'bad'.
As long as we observe !NULL, we'll acquire ctx->lock. If we acquire it
first and not see the event yet, then CPU0 must observe task_curr()
and retry. If the install happens first, then we must see the event on
sched-in and all is well.
I think we can translate the first part (until the 'must not be NULL')
of the scenario to a litmus test like:
Where:
x is perf_event_ctxp[],
y is our tasks's CPU, and
z is our task being placed on the rq of CPU2.
The P0 smp_mb() is the one added by this patch, ordering the store to
perf_event_ctxp[] from find_get_context() and the load of task_cpu()
in task_function_call().
The smp_store_release/smp_load_acquire model the RCpc locking of the
rq->lock and the smp_mb() of P2 is the context switch switching from
whatever CPU2 was running to our task 't'.
ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.
This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.
Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.
Reported-by: Elektra Wagenrad <onelektra@gmx.net> Signed-off-by: Felix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read_pmem() function uses memcpy_mcsafe() on x86 where an EFAULT
error code indicates a failed read. Block I/O should use EIO to
indicate failure. Other pmem code paths (like bad blocks) already use
EIO so let's be consistent.
This fixes compatibility with consumers like btrfs that try to parse the
specific error code rather than treat all errors the same.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when vce idle, set vce clock gate, so the clock
in vce domain will be disabled.
when need to encode, disable vce clock gate,
enable the clocks to vce engine.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While probing BGX we requesting appropriate QLM for it's configuration
and get LMAC count by that request. Then, while reading configured
MAC values from SSDT table we need to save them in proper mapping:
BGX[i]->lmac[j].mac = <MAC value>
to later provide for initialization stuff. In order to fill
such mapping properly we need to add lmac index to be used while
acpi initialization since at this moment bgx->lmac_count already contains
actual value.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_RANDOMIZE_MODULE_REGION_FULL=y, the offset between loaded
modules and the core kernel may exceed 4 GB, putting symbols exported
by the core kernel out of the reach of the ordinary adrp/add instruction
pairs used to generate relative symbol references. So make the adr_l
macro emit a movz/movk sequence instead when executing in module context.
While at it, remove the pointless special case for the stack pointer.
Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to
NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset()
attempts to free the memory again.
Signed-off-by: Roberto Sassu <rsassu@suse.de> Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for the Asus Touchpad was recently added. It turns out this
device can fail initialisation (and become unusable) when the RESET
command is sent too soon after the POWER ON command.
Unfortunately the i2c-hid specification does not specify the need for
a delay between these two commands. But it was discovered the Windows
driver has a 1ms delay.
As a result, this patch modifies the i2c-hid module to add a sleep
inbetween the POWER ON and RESET commands which lasts between 1ms and 5ms.
See https://github.com/vlasenko/hid-asus-dkms/issues/24 for further
details.
When an associated station changes its VHT operating mode this
can/will affect the bandwidth it's using, and consequently we
must recalculate the minimum bandwidth we need to use. Failure
to do so can lead to one of two scenarios:
1) we use a too high bandwidth, this is benign
2) we use a too narrow bandwidth, causing rate control and
actual PHY configuration to be out of sync, which can in
turn cause problems/crashes
When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the
fiber page is used for the SGMII host-side connection. The PHY driver
notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page
for the link status, and ends up reading the MAC-side status instead of
the outgoing (copper) link. This leads to incorrect results reported
via ethtool.
If the PHY is connected via SGMII to the host, ignore the fiber page.
However, continue to allow the existing power management code to
suspend and resume the fiber page.
Fixes: 6cfb3bcc0641 ("Marvell phy: check link status in case of fiber link.") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hswep_uncore_cpu_init() uses a hardcoded physical package id 0 for the boot
cpu. This works as long as the boot CPU is actually on the physical package
0, which is normaly the case after power on / reboot.
But it fails with a NULL pointer dereference when a kdump kernel is started
on a secondary socket which has a different physical package id because the
locigal package translation for physical package 0 does not exist.
Use the logical package id of the boot cpu instead of hard coded 0.
[ tglx: Rewrote changelog once more ]
Fixes: cf6d445f6897 ("perf/x86/uncore: Track packages, not per CPU data") Signed-off-by: Prarit Bhargava <prarit@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@suse.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Harish Chegondi <harish.chegondi@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1483628965-2890-1-git-send-email-prarit@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After rollover of the IOVA space, we want to get a low IOVA address,
otherwise the the games we play by remembering the last IOVA are
pointless. When we search for a free hole with DRM_MM_SEARCH_DEFAULT,
drm_mm will pop the next entry from the free holes stack, which will
likely be a high IOVA. By using DRM_MM_SEARCH_BELOW we can trick
drm_mm into reversing the search and provide us with a low IOVA.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Wladimir van der Laan <laanwj@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: John Crispin <john@phrozen.org> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head
(or skb->data), or risk use after free.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I don't have any guests with PAGE_SIZE > 64k but the
code seems to be clearly broken in that case
as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need
more than 8 bit and so the code in mergeable_ctx_to_buf_address
does not give us the actual true size.
Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mlxsw_sp_nexthop_group_mac_update() is called in one of two cases:
1) When the MAC of a nexthop needs to be updated
2) When the size of a nexthop group has changed
In the second case the adjacency entries for the nexthop group need to
be reallocated from the adjacency table. In this case we must write to
the entries the MAC addresses of all the nexthops that should be
offloaded and not only those whose MAC changed. Otherwise, these entries
would be filled with garbage data, resulting in packet loss.
Fixes: a7ff87acd995 ("mlxsw: spectrum_router: Implement next-hop routing") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recently added mediated VFIO driver doesn't know about powerpc iommu.
It thus doesn't register a struct iommu_table_group in the iommu group
upon device creation. The iommu_data pointer hence remains null.
This causes a kernel oops when userspace tries to set the iommu type of a
container associated with a mediated device to VFIO_SPAPR_TCE_v2_IOMMU.
Return success when the ring is properly initialized, otherwise return
failure.
Tonga SRIOV VF doesn't have UVD and VCE engines, the initialization of
these IPs is bypassed. The system crashes if application submit IB to
their rings which are not ready to use. It could be a common issue if
IP having ring buffer is disabled for some reason on specific ASIC, so
it should check the ring being ready to use.
Bug: amdgpu_test crashes system on Tonga VF.
Signed-off-by: Ding Pixel <Pixel.Ding@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check the return value of phy_connect_direct() in
dsa_slave_phy_connect() otherwise we may be continuing the
initialization of a slave network device with a PHY that already
attached somewhere else and which will soon be in error because the PHY
device is in error.
The conditions for such an error to occur are that we have a port of our
switch that is not disabled, and has the same port number as a PHY
address (say both 5) that can be probed using the DSA slave MII bus. We
end-up having this slave network device find a PHY at the same address
as our port number, and we try to attach to it.
A slave network (e.g: port 0) has already attached to our PHY device,
and we try to re-attach it with a different network device, but since we
ignore the error we would end-up initializating incorrect device
references by the time the slave network interface is opened.
The code has been (re)organized several times, making it hard to provide
an exact Fixes tag, this is a bugfix nonetheless.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Ideapad laptops, ACPI event 1 is currently not handled. Many models
log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while
running on battery power. Some convertible laptops receive this event
when switching in and out of tablet mode.
This adds and additional case for event 1 in ideapad_acpi_notify to call
ideapad_input_report(priv, vpc_bit), so that the event is reported to
userspace and we avoid unnecessary logging.
A recent firmware change seems to have enabled thermal zones on the
iwlwifi driver. Unfortunately, my device fails when registering the
thermal zone. This doesn't stop the driver from attempting to unregister
the thermal zone at unload time, triggering a NULL pointer deference in
strlen() off the thermal_zone_device_unregister() path.
Don't unregister if name is NULL, for that case we failed registering.
Do the same for the cooling zone.
Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally. Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed. Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.
However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host. The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.
That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either. The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there. The
calling sequence provides a bit of distinction for us:
A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two. But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully. The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):
I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com> Reviewed-by: Fam Zheng <famz@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During an OOM scenario, request slots could not be created as skb
allocation fails. So the netback cannot pass in packets and netfront
wrongly assumes that there is no more work to be done and it disables
polling. This causes Rx to stall.
The issue is with the retry logic which schedules the timer if the
created slots are less than NET_RX_SLOTS_MIN. The count of new request
slots to be pushed are calculated as a difference between new req_prod
and rsp_cons which could be more than the actual slots, if there are
unconsumed responses.
The fix is to calculate the count of newly created slots as the
difference between new req_prod and old req_prod.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original
page is not suitable, we swap it for another page from the swiotlb
pool.
In these cases, we don't update the previously calculated dma address
for the page before calling xen_dma_map_page. Thus, we end up calling
xen_dma_map_page passing the wrong dev_addr, resulting in
xen_dma_map_page mistakenly assuming that the page is foreign when it is
local.
Fix the bug by updating dev_addr appropriately.
This change has no effect on x86, because xen_dma_map_page is a stub
there.
Using control_work instead of config_work as the 3rd argument to
container_of results in an invalid portdev pointer. Indeed, the work
structure is initialized as below:
It leads to a crash when portdev->vdev is dereferenced later. This
bug
is triggered when the guest uses a virtio-console without multiport
feature and receives a config_changed virtio interrupt.
Signed-off-by: G. Campana <gcampana@quarkslab.com> Reviewed-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In NO_HOLES mode, we don't have the [hole] extent any more.
Commit c1aa45759e90 ("Btrfs: fix shrinking truncate when the no_holes feature is enabled")
fixed disk isize not being updated in NO_HOLES mode when data is not flushed.
However, even if data has been flushed, we can still have trouble
in updating disk isize since we updated disk isize to 'start' of
the last evicted extent.
Reviewed-by: Chris Mason <clm@fb.com> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following deadlock is seen when executing generic/113 test,
---------------------------------------------------------+----------------------------------------------------
Direct I/O task Fast fsync task
---------------------------------------------------------+----------------------------------------------------
btrfs_direct_IO
__blockdev_direct_IO
do_blockdev_direct_IO
do_direct_IO
btrfs_get_blocks_direct
while (blocks needs to written)
get_more_blocks (first iteration)
btrfs_get_blocks_direct
btrfs_create_dio_extent
down_read(&BTRFS_I(inode) >dio_sem)
Create and add extent map and ordered extent
up_read(&BTRFS_I(inode) >dio_sem)
btrfs_sync_file
btrfs_log_dentry_safe
btrfs_log_inode_parent
btrfs_log_inode
btrfs_log_changed_extents
down_write(&BTRFS_I(inode) >dio_sem)
Collect new extent maps and ordered extents
wait for ordered extent completion
get_more_blocks (second iteration)
btrfs_get_blocks_direct
btrfs_create_dio_extent
down_read(&BTRFS_I(inode) >dio_sem)
--------------------------------------------------------------------------------------------------------------
In the above description, Btrfs direct I/O code path has not yet started
submitting bios for file range covered by the initial ordered
extent. Meanwhile, The fast fsync task obtains the write semaphore and
waits for I/O on the ordered extent to get completed. However, the
Direct I/O task is now blocked on obtaining the read semaphore.
To resolve the deadlock, this commit modifies the Direct I/O code path
to obtain the read semaphore before invoking
__blockdev_direct_IO(). The semaphore is then given up after
__blockdev_direct_IO() returns. This allows the Direct I/O code to
complete I/O on all the ordered extents it creates.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds two helpers, bpf_map_area_alloc() and bpf_map_area_free(),
that are to be used for map allocations. Using kmalloc() for very large
allocations can cause excessive work within the page allocator, so i) fall
back earlier to vmalloc() when the attempt is considered costly anyway,
and even more importantly ii) don't trigger OOM killer with any of the
allocators.
Since this is based on a user space request, for example, when creating
maps with element pre-allocation, we really want such requests to fail
instead of killing other user space processes.
Also, don't spam the kernel log with warnings should any of the allocations
fail under pressure. Given that, we can make backend selection in
bpf_map_area_alloc() generic, and convert all maps over to use this API
for spots with potentially large allocation requests.
Note, replacing the one kmalloc_array() is fine as overflow checks happen
earlier in htab_map_alloc(), since it must also protect the multiplication
for vmalloc() should kmalloc_array() fail.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the TPA GRO code path, initialize the tcp_opt_len variable to 0 so
that it will be correct for packets without TCP timestamps. The bug
caused the SKB fields to be incorrectly set up for packets without
TCP timestamps, leading to these packets being rejected by the stack.
Reported-by: Andy Gospodarek <andrew.gospodarek@broadocm.com> Acked-by: Andy Gospodarek <andrew.gospodarek@broadocm.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vif->lock is used to protect statistics gathering agents from using the
queue structure during cleaning.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate memory leaks introduced several years ago by cleaning the
queue resources which are allocated on XenBus connection event. Namely, queue
structure array and pages used for IO rings.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ethtool channels respond struct was uninitialized when querying device
channel boundaries settings. As a result, unreported fields by the driver
hold garbage. This may cause sending unsupported params to driver.
Fixes: 8bf368620486 ('ethtool: ensure channel counts are within bounds ...') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> CC: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We give up recovery on permanent error, simply shutdown the affected
devices and remove them. If the devices can't be put into quiet state,
they spew more traffic that is likely to cause another unexpected EEH
error. This was observed on "p8dtu2u" machine:
On P8 PowerNV platform, the IO path is frozen when shutdowning the
devices, meaning the memory registers are inaccessible. It is why
the devices can't be put into quiet state before removing them.
This fixes the issue by enabling IO path prior to putting the devices
into quiet state.
Commit beb0babfb77e ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes: beb0babfb77e ("korina: disable napi on close and restart") Reported-by: Alexandros C. Couloumbis <alex@ozo.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPU hotplug function intel_pmu_cpu_starting() sets
cpu_hw_events.excl_thread_id unconditionally to 1 when the shared exclusive
counters data structure is already availabe for the sibling thread.
This works during the boot process because the first sibling gets threadid
0 assigned and the second sibling which shares the data structure gets 1.
But when the first thread of the core is offlined and onlined again it
shares the data structure with the second thread and gets exclusive thread
id 1 assigned as well.
Prevent this by checking the threadid of the already online thread.
need to clear bit31-29 in GRBM_GFX_INDEX,
then the program can be valid.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corrupted ATIO is defined as length of fcp_header & fcp_cmd
payload is less than 0x38. It's the minimum size for a frame to
carry 8..16 bytes SCSI CDB. The exchange will be dropped or
terminated if corrupted.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch title ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value. This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt. Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt. It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zoned block devices force the use of READ/WRITE(16) commands by setting
sdkp->use_16_for_rw and clearing sdkp->use_10_for_rw. This result in
DPOFUA always being disabled for these drives as the assumed use of
the deprecated READ/WRITE(6) commands only looks at sdkp->use_10_for_rw.
Strenghten the test by also checking that sdkp->use_16_for_rw is false.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
emulator_fix_hypercall() replaces hypercall with vmcall instruction,
but it does not handle GP exception properly when writes the new instruction.
It can return X86EMUL_PROPAGATE_FAULT without setting exception information.
This leads to incorrect emulation and triggers
WARN_ON(ctxt->exception.vector > 0x1f) in x86_emulate_insn()
as discovered by syzkaller fuzzer:
The be structure must not be freed when freeing the blkif structure
isn't done. Otherwise a use-after-free of be when unmapping the ring
used for communicating with the frontend will occur in case of a
late call of xenblk_disconnect() (e.g. due to an I/O still active
when trying to disconnect).
Signed-off-by: Juergen Gross <jgross@suse.com> Tested-by: Steven Haigh <netwiz@crc.id.au> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OdroidC2 GbE link breaks under heavy tx transfer. This happens even if the
MAC does not enable Energy Efficient Ethernet (No Low Power state Idle on
the Tx path). The problem seems to come from the phy Rx path, entering the
LPI state.
Disabling EEE advertisement on the phy prevent this feature to be
negociated with the link partner and solve the issue.
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In genphy_config_eee_advert, the return value of phy_read_mmd_indirect is
checked to know if the register could be accessed but the result is
assigned to a 'u32'.
Changing to 'int' to correctly get errors from phy_read_mmd_indirect.
Fixes: d853d145ea3e ("net: phy: add an option to disable EEE advertisement") Reported-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Yegor Yefremov <yegorslists@googlemail.com> Tested-by: Andreas Färber <afaerber@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduce support for 2500BaseT and 5000BaseT link modes.
These modes are included in the new IEEE 802.3bz standard.
Signed-off-by: Pavel Belous <pavel.s.belous@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error queues use a non-zero first word to detect if the queues are full.
Using pages that have not been zeroed may result in false positive
overflow events. These queues are set up once during boot so zeroing
all mondo and error queue pages is safe.
Note that the false positive overflow does not always occur because the
page allocation for these queues is so early in the boot cycle that
higher number CPUs get fresh pages. It is only when traps are serviced
with lower number CPUs who were given already used pages that this issue
is exposed.
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User processes trying to access an invalid memory address via PIO will
receive a SIGBUS signal instead of causing a panic. Memory errors will
receive a SIGKILL since a SIGBUS may result in a coredump which may
attempt to repeat the faulting access.
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by
waiting until the pmd is unlocked before we return and retry. However,
we can race with migrate_misplaced_transhuge_page():
// do_huge_pmd_numa_page // migrate_misplaced_transhuge_page()
// Holds 0 refs on page // Holds 2 refs on page
vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
/* ... */
if (pmd_trans_migrating(*vmf->pmd)) {
page = pmd_page(*vmf->pmd);
spin_unlock(vmf->ptl);
ptl = pmd_lock(mm, pmd);
if (page_count(page) != 2)) {
/* roll back */
}
/* ... */
mlock_migrate_page(new_page, page);
/* ... */
spin_unlock(ptl);
put_page(page);
put_page(page); // page freed here
wait_on_page_locked(page);
goto out;
}
This can result in the freed page having its waiters flag set
unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the
page alloc/free functions. This has been observed on arm64 KVM guests.
We can avoid this by having do_huge_pmd_numa_page() take a reference on
the page before dropping the pmd lock, mirroring what we do in
__migration_entry_wait().
When we hit the race, migrate_misplaced_transhuge_page() will see the
reference and abort the migration, as it may do today in other cases.
Fixes: b8916634b77bffb2 ("mm: Prevent parallel splits during THP migration") Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.com Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Steve Capper <steve.capper@arm.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of l2tp_nl_session_find() need to hold a reference on the
returned session since there's no guarantee that it isn't going to
disappear from under them.
Relying on the fact that no l2tp netlink message may be processed
concurrently isn't enough: sessions can be deleted by other means
(e.g. by closing the PPPOL2TP socket of a ppp pseudowire).
l2tp_nl_cmd_session_delete() is a bit special: it runs a callback
function that may require a previous call to session->ref(). In
particular, for ppp pseudowires, the callback is l2tp_session_delete(),
which then calls pppol2tp_session_close() and dereferences the PPPOL2TP
socket. The socket might already be gone at the moment
l2tp_session_delete() calls session->ref(), so we need to take a
reference during the session lookup. So we need to pass the do_ref
variable down to l2tp_session_get() and l2tp_session_get_by_ifname().
Since all callers have to be updated, l2tp_session_find_by_ifname() and
l2tp_nl_session_find() are renamed to reflect their new behaviour.
Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2tp_session_find() doesn't take any reference on the returned session.
Therefore, the session may disappear while sending the notification.
Use l2tp_session_get() instead and decrement session's refcount once
the notification is sent.
Fixes: 33f72e6f0c67 ("l2tp : multicast notification to the registered listeners") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2tp_session_create() relies on its caller for checking for duplicate
sessions. This is racy since a session can be concurrently inserted
after the caller's verification.
Fix this by letting l2tp_session_create() verify sessions uniqueness
upon insertion. Callers need to be adapted to check for
l2tp_session_create()'s return code instead of calling
l2tp_session_find().
pppol2tp_connect() is a bit special because it has to work on existing
sessions (if they're not connected) or to create a new session if none
is found. When acting on a preexisting session, a reference must be
held or it could go away on us. So we have to use l2tp_session_get()
instead of l2tp_session_find() and drop the reference before exiting.
Fixes: d9e31d17ceba ("l2tp: Add L2TP ethernet pseudowire support") Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Holding a reference on session is required before calling
pppol2tp_session_ioctl(). The session could get freed while processing the
ioctl otherwise. Since pppol2tp_session_ioctl() uses the session's socket,
we also need to take a reference on it in l2tp_session_get().
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Taking a reference on sessions in l2tp_recv_common() is racy; this
has to be done by the callers.
To this end, a new function is required (l2tp_session_get()) to
atomically lookup a session and take a reference on it. Callers then
have to manually drop this reference.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system try to close /dev/usb-ffs/adb/ep0 on one core, at the same
time another core try to attach new UDC, which will cause deadlock as
below scenario. Thus we should release ffs lock before issuing
unregister_gadget_item().
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Moyer reported that on his system with two memory regions 0~64G and
1T~1T+192G, and kernel option "memmap=192G!1024G" added, enabling KASLR
will make the system hang intermittently during boot. While adding 'nokaslr'
won't.
This crash happens because the for loop count calculation in sync_global_pgds()
is not correct. When a mapping area crosses PGD entries, we should
calculate the starting address of region which next PGD covers and assign
it to next for loop count, but not add PGDIR_SIZE directly. The old
code works right only if the mapping area is an exact multiple of PGDIR_SIZE,
otherwize the end region could be skipped so that it can't be synchronized
to all other processes from kernel PGD init_mm.pgd.
In Jeff's system, emulated pmem area [1024G, 1216G) is smaller than
PGDIR_SIZE. While 'nokaslr' works because PAGE_OFFSET is 1T aligned, it
makes this area be mapped inside one PGD entry. With KASLR enabled,
this area could cross two PGD entries, then the next PGD entry won't
be synced to all other processes. That is why we saw empty PGD.
Fix it.
Reported-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Baoquan He <bhe@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dave Young <dyoung@redhat.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jinbum Park <jinb.park7@gmail.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yasuaki Ishimatsu <yasu.isimatu@gmail.com> Cc: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/1493864747-8506-1-git-send-email-bhe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dm_pool_inc_data_range() fails, dm thin aborts current metadata
transaction and marks pool as PM_READ_ONLY. Memory for thin mapping
is released as well. However, current thin mapping will be queued
onto next stage as part of queue_passdown_pt2() or passdown_endio().
This dangling thin mapping memory when processed and accessed in
next stage will lead to device mapper crashing.
Code flow without fix:
-> process_prepared_discard_passdown_pt1(m)
-> dm_thin_remove_range()
-> discard passdown
--> passdown_endio(m) queues m onto next stage
-> dm_pool_inc_data_range() fails, frees memory m
but does not remove it from next stage queue
-> process_prepared_discard_passdown_pt2(m)
-> processes freed memory m and crashes
The fix is to first take the block ref count for discarded block and
then do a passdown discard of this block. If block ref count fails,
then bail out aborting current metadata transaction, mark pool as
PM_READ_ONLY and also free current thin mapping memory (existing error
handling code) without queueing this thin mapping onto next stage of
processing. If block ref count succeeds, then passdown discard of this
block. Discard callback of passdown_endio() will queue this thin mapping
onto next stage of processing.
Code flow with fix:
-> process_prepared_discard_passdown_pt1(m)
-> dm_thin_remove_range()
-> dm_pool_inc_data_range()
--> if fails, free memory m and bail out
-> discard passdown
--> passdown_endio(m) queues m onto next stage
The hash table created during vmw_cmdbuf_res_man_create was
never freed. This causes memory leak in context creation.
Added the corresponding drm_ht_remove in vmw_cmdbuf_res_man_destroy.
Tested for memory leak by running piglit overnight and kernel
memory is not inflated which earlier was.
projects / users / dwmw2 / linux.git / log