These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with phy->symbol_duration in order to get these
values in microseconds.
Drivers are expected to set the PHY current_channel and current_page
according to their default state. The hwsim driver is advertising being
configured on channel 13 by default but that is not reflected in its own
internal pib structure. In order to ensure that this driver consider the
current channel as being 13 internally, we at least need to set the
pib->channel field to 13.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[stefan@datenfreihafen.org: fixed assigment from page to channel] Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20220125121426.848337-2-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This check misses checking for platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.
Fixes: 454fa271bc4e ("spi: Add Meson SPICC driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some case, like after a transfer timeout, master->cur_msg pointer
is NULL which led to a kernel crash when trying to use master->cur_msg->spi.
mtk_spi_can_dma(), pointed by master->can_dma, doesn't use this parameter
avoid the problem by setting NULL as second parameter.
Fixes: a568231f46322 ("spi: mediatek: Add spi bus for Mediatek MT8173") Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Link: https://lore.kernel.org/r/20220131141708.888710-1-benjamin.gaignard@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apply only valid chip select value. This change fixes case where chip
select is set to initial value of '-1' during probe and PM supend and
subsequent resume can try to use the value with undefined behaviour.
Also in case where gpio based chip select, the check in
bcm_qspi_chip_select() shall prevent undefined behaviour on resume.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220127185359.27322-1-kdasu.kdev@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polling loop for the register change in iommu_ga_log_enable() needs
to have a udelay() in it. Otherwise the CPU might be faster than the
IOMMU hardware and wrongly trigger the WARN_ON() further down the code
stream. Use a 10us for udelay(), has there is some hardware where
activation of the GA log can take more than a 100ms.
A future optimization should move the activation check of the GA log
to the point where it gets used for the first time. But that is a
bigger change and not suitable for a fix.
After commit e3beca48a45b ("irqdomain/treewide: Keep firmware node
unconditionally allocated"). For tear down scenario, fn is only freed
after fail to allocate ir_domain, though it also should be freed in case
dmar_enable_qi returns error.
Besides free fn, irq_domain and ir_msi_domain need to be removed as well
if intel_setup_irq_remapping fails to enable queued invalidation.
Improve the rewinding path by add out_free_ir_domain and out_free_fwnode
lables per Baolu's suggestion.
The failure to allocate memory during MLX4_DEV_EVENT_PORT_MGMT_CHANGE
event handler will cause skip the assignment logic, but
ib_dispatch_event() will be called anyway.
Fix it by calling to return instead of break after memory allocation
failure.
Fixes: 00f5ce99dc6e ("mlx4: Use port management change event instead of smp_snoop") Link: https://lore.kernel.org/r/12a0e83f18cfad4b5f62654f141e240d04915e10.1643622264.git.leonro@nvidia.com Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.
An analysis of the code with this patch applied shows:
ret = init_clks(pdev, clk);
if (ret)
return ERR_PTR(ret);
...
for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
struct clk *c = clk[data->clk_id[j]];
Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a6d needs to be
reverted.
Fixes: 9de2b9286a6d ("ASoC: mediatek: Check for error clk pointer") Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn> Cc: Mark Brown <broonie@kernel.org> Cc: James Liao <jamesjj.liao@mediatek.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Matthias Brugger <matthias.bgg@gmail.com Cc: Frank Wunderlich <frank-w@public-files.de> Cc: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/lkml/20220205014755.699603-1-linux@roeck-us.net/ Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 309a62fa3a9e ("bio-integrity: bio_integrity_advance must update
integrity seed") added code to update the integrity seed value when
advancing a bio. However, it failed to take into account that the
integrity interval might be larger than the 512-byte block layer
sector size. This broke bio splitting on PI devices with 4KB logical
blocks.
The seed value should be advanced by bio_integrity_intervals() and not
the number of sectors.
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org> Fixes: 4d4e9907ff572 ("drm/nouveau/bios: guard against out-of-bounds accesses to image") Cc: <stable@vger.kernel.org> # v4.10+ Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit switches the Gigabyte X570 Aorus Xtreme from using the
ALC1220_FIXUP_CLEVO_P950 to the ALC1220_FIXUP_GB_X570 quirk. This fixes
the no-audio after reboot from windows problem.
Newer versions of the X570 Master come with a newer revision of the
mainboard chipset - the X570S. These boards have the same ALC1220 codec
but seem to initialize the codec with a different parameter in Coef 0x7
which causes the output audio to be very low. We therefore write a
known-good value to Coef 0x7 to fix that. As the value is the exact same
as on the other X570(non-S) boards the same quirk-function can be shared
between both generations.
This commit adds the Gigabyte X570S Aorus Master to the list of boards
using the ALC1220_FIXUP_GB_X570 quirk. This fixes both, the silent output
and the no-audio after reboot from windows problems.
This work has been tested by the folks over at the level1techs forum here:
https://forum.level1techs.com/t/has-anybody-gotten-audio-working-in-linux-on-aorus-x570-master/154072
The initial commit of the new Gigabyte X570 ALC1220 quirks lacked the
fixup-model entry in alc882_fixup_models[]. It seemed not to cause any ill
effects but for completeness sake this commit makes up for that.
We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.
We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.
We don't currently validate that the values being set are within the range
we advertised to userspace as being valid, do so and reject any values
that are out of range.
When an admin enables audit at early boot via the "audit=1" kernel
command line the audit queue behavior is slightly different; the
audit subsystem goes to greater lengths to avoid dropping records,
which unfortunately can result in problems when the audit daemon is
forcibly stopped for an extended period of time.
This patch makes a number of changes designed to improve the audit
queuing behavior so that leaving the audit daemon in a stopped state
for an extended period does not cause a significant impact to the
system.
- kauditd_send_queue() is now limited to looping through the
passed queue only once per call. This not only prevents the
function from looping indefinitely when records are returned
to the current queue, it also allows any recovery handling in
kauditd_thread() to take place when kauditd_send_queue()
returns.
- Transient netlink send errors seen as -EAGAIN now cause the
record to be returned to the retry queue instead of going to
the hold queue. The intention of the hold queue is to store,
perhaps for an extended period of time, the events which led
up to the audit daemon going offline. The retry queue remains
a temporary queue intended to protect against transient issues
between the kernel and the audit daemon.
- The retry queue is now limited by the audit_backlog_limit
setting, the same as the other queues. This allows admins
to bound the size of all of the audit queues on the system.
- kauditd_rehold_skb() now returns records to the end of the
hold queue to ensure ordering is preserved in the face of
recent changes to kauditd_send_queue().
Cc: stable@vger.kernel.org Fixes: 5b52330bbfe63 ("audit: fix auditd/kernel connection state tracking") Fixes: f4b3ee3c85551 ("audit: improve robustness of the audit queue handling") Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com> Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.
Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.
BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt
write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
fanout_add net/packet/af_packet.c:1791 [inline]
packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000000000000000 -> 0xffff888106f8c000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 47dceb8ecdc1 ("packet: add classic BPF fanout mode") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While looking at one unrelated syzbot bug, I found the replay logic
in __rtnl_newlink() to potentially trigger use-after-free.
It is better to clear master_dev and m_ops inside the loop,
in case we have to replay it.
Fixes: ba7d49b1f0f8 ("rtnetlink: provide api for getting and setting slave info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20220201012106.216495-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There will be BUG_ON() triggered in include/linux/skbuff.h leading to
intermittent kernel panic, when the skb length underflow is detected.
Fix this by dropping the packet if such length underflows are seen
because of inconsistencies in the hardware descriptors.
Fixes: 622c36f143fc ("amd-xgbe: Fix jumbo MTU processing on newer hardware") Suggested-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Link: https://lore.kernel.org/r/20220127092003.2812745-1-Shyam-sundar.S-k@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When rx_buf is allocated we need to account for IPHETH_IP_ALIGN,
which reduces the usable size by 2 bytes. Otherwise we have 1512
bytes usable instead of 1514, and if we receive more than 1512
bytes, ipheth_rcvbulk_callback is called with status -EOVERFLOW,
after which the driver malfunctiones and all communication stops.
In case almost or all available ports are taken, clash resolution can
take a very long time, resulting in soft lockup.
This can happen when many to-be-natted hosts connect to same
destination:port (e.g. a proxy) and all connections pass the same SNAT.
Pick a random offset in the acceptable range, then try ever smaller
number of adjacent port numbers, until either the limit is reached or a
useable port was found. This results in at most 248 attempts
(128 + 64 + 32 + 16 + 8, i.e. 4 restarts with new search offset)
instead of 64000+,
This is a leftover from days where single-cpu systems were common:
Store last port used to resolve a clash to use it as a starting point when
the next conflict needs to be resolved.
When we have parallel attempt to connect to same address:port pair,
its likely that both cores end up computing the same "available" port,
as both use same starting port, and newly used ports won't become
visible to other cores until the conntrack gets confirmed later.
One of the cores then has to drop the packet at insertion time because
the chosen new tuple turns out to be in use after all.
Lets simplify this: remove port rover and use a pseudo-random starting
point.
Note that this doesn't make netfilter default to 'fully random' mode;
the 'rover' was only used if NAT could not reuse source port as-is.
In commit 431280eebed9 ("ipv4: tcp: send zero IPID for RST and
ACK sent in SYN-RECV and TIME-WAIT state") we took care of some
ctl packets sent by TCP.
It turns out we need to use a similar strategy for SYNACK packets.
By default, they carry IP_DF and IPID==0, but there are ways
to ask them to use the hashed IP ident generator and thus
be used to build off-path attacks.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
One of this way is to force (before listener is started)
echo 1 >/proc/sys/net/ipv4/ip_no_pmtu_disc
Another way is using forged ICMP ICMP_FRAG_NEEDED
with a very small MTU (like 68) to force a false return from
ip_dont_fragment()
In this patch, ip_build_and_send_pkt() uses the following
heuristics.
1) Most SYNACK packets are smaller than IPV4_MIN_MTU and therefore
can use IP_DF regardless of the listener or route pmtu setting.
2) In case the SYNACK packet is bigger than IPV4_MIN_MTU,
we use prandom_u32() generator instead of the IPv4 hashed ident one.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Ray Che <xijiache@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Cc: Geoff Alexander <alexandg@cs.unm.edu> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For some reason, raw_bind() forgot to lock the socket.
BUG: KCSAN: data-race in __ip4_datagram_connect / raw_bind
write to 0xffff8881170d4308 of 4 bytes by task 5466 on cpu 0:
raw_bind+0x1b0/0x250 net/ipv4/raw.c:739
inet_bind+0x56/0xa0 net/ipv4/af_inet.c:443
__sys_bind+0x14b/0x1b0 net/socket.c:1697
__do_sys_bind net/socket.c:1708 [inline]
__se_sys_bind net/socket.c:1706 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1706
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881170d4308 of 4 bytes by task 5468 on cpu 1:
__ip4_datagram_connect+0xb7/0x7b0 net/ipv4/datagram.c:39
ip4_datagram_connect+0x2a/0x40 net/ipv4/datagram.c:89
inet_dgram_connect+0x107/0x190 net/ipv4/af_inet.c:576
__sys_connect_file net/socket.c:1900 [inline]
__sys_connect+0x197/0x1b0 net/socket.c:1917
__do_sys_connect net/socket.c:1927 [inline]
__se_sys_connect net/socket.c:1924 [inline]
__x64_sys_connect+0x3d/0x50 net/socket.c:1924
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x0003007f
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 5468 Comm: syz-executor.5 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 0781168e23a2 ("yam: fix a missing-check bug") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ibmvnic_tasklet() continuously spins waiting for responses to all
capability requests. It does this to avoid encountering an error
during initialization of the vnic. However if there is a bug in the
VIOS and we do not receive a response to one or more queries the
tasklet ends up spinning continuously leading to hard lock ups.
If we fail to receive a message from the VIOS it is reasonable to
timeout the login attempt rather than spin indefinitely in the tasklet.
Fixes: 249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We use ->running_cap_crqs to determine when the ibmvnic_tasklet() should
send out the next protocol message type. i.e when we get back responses
to all our QUERY_CAPABILITY CRQs we send out REQUEST_CAPABILITY crqs.
Similiary, when we get responses to all the REQUEST_CAPABILITY crqs, we
send out the QUERY_IP_OFFLOAD CRQ.
We currently increment ->running_cap_crqs as we send out each CRQ and
have the ibmvnic_tasklet() send out the next message type, when this
running_cap_crqs count drops to 0.
This assumes that all the CRQs of the current type were sent out before
the count drops to 0. However it is possible that we send out say 6 CRQs,
get preempted and receive all the 6 responses before we send out the
remaining CRQs. This can result in ->running_cap_crqs count dropping to
zero before all messages of the current type were sent and we end up
sending the next protocol message too early.
Instead initialize the ->running_cap_crqs upfront so the tasklet will
only send the next protocol message after all responses are received.
Use the cap_reqs local variable to also detect any discrepancy (either
now or in future) in the number of capability requests we actually send.
Currently only send_query_cap() is affected by this behavior (of sending
next message early) since it is called from the worker thread (during
reset) and from application thread (during ->ndo_open()) and they can be
preempted. send_request_cap() is only called from the tasklet which
processes CRQ responses sequentially, is not be affected. But to
maintain the existing symmtery with send_query_capability() we update
send_request_capability() also.
Fixes: 249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Renaming a file is required by POSIX to update the file ctime, so
ensure that the file data is synced to disk so that we don't clobber the
updated ctime by writing back after creating the hard link.
Fixes: f2c2c552f119 ("NFS: Move delegation recall into the NFSv4 callback for rename_setup()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Creating a hard link is required by POSIX to update the file ctime, so
ensure that the file data is synced to disk so that we don't clobber the
updated ctime by writing back after creating the hard link.
Fixes: 9f7682728728 ("NFS: Move the delegation return down into nfs4_proc_link()") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 15701 Comm: syz-executor.2 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
The Fixes tag I chose is probably arbitrary, I do not think
we need to backport this patch to older kernels.
Fixes: c5cff8561d2d ("ipv6: add rcu grace period before freeing fib6_node") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20220120174112.1126644-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit:7866a621043f ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.
Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:
Before:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
After:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
ALL ens192 tpacket_rcv
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
v1 -> v2:
- fix the regression rather than adding new /proc API as
suggested by Stephen Hemminger.
Fixes: 7866a621043f ("dev: add per net_device packet type chains") Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the application sets the O_DIRECTORY flag, and tries to open a
regular file, nfs_atomic_open() will punt to doing a regular lookup.
If the server then returns a regular file, we will happily return a
file descriptor with uninitialised open state.
The fix is to return the expected ENOTDIR error in these cases.
According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.
Fixes: ae544f64cc7b ("hwmon: (lm90) Add support for GMT G781") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.
As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.
Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT
Fixes: 73f156a6e8c1 ("inetpeer: get rid of ip_id_count") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reported-by: Ray Che <xijiache@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
the selftests 'router_broadcast.sh' will fail, as such command
# ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b
can't receive the response skb by the PING socket. It's caused by mismatch
of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket,
as dif is vrf-h1 if dif's master was set to vrf-h1.
This patch is to fix this regression by also checking the sk_bound_dev_if
against sdif so that the packets can stil be received even if the socket
is not bound to the vrf device but to the real iif.
Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In one net namespace, after creating a packet socket without binding
it to a device, users in other net namespaces can observe the new
`packet_type` added by this packet socket by reading `/proc/net/ptype`
file. This is minor information leakage as packet socket is
namespace aware.
Add a net pointer in `packet_type` to keep the net namespace of
of corresponding packet socket. In `ptype_seq_show`, this net pointer
must be checked when it is not NULL.
Fixes: 2feb27dbe00c ("[NETNS]: Minor information leak via /proc/net/ptype file.") Signed-off-by: Congyu Liu <liu3101@purdue.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bnx2fc_destroy() functions are removing the interface before calling
destroy_work. This results multiple WARNings from sysfs_remove_group() as
the controller rport device attributes are removed too early.
Replace the fcoe_port's destroy_work queue. It's not needed.
The problem is easily reproducible with the following steps.
struct rpmsg_eptdev contains a struct cdev. The current code frees
the rpmsg_eptdev struct in rpmsg_eptdev_destroy(), but the cdev is
a managed object, therefore its release is not predictable and the
rpmsg_eptdev could be freed before the cdev is entirely released.
The cdev_device_add/del() API was created to address this issue
(see commit '233ed09d7fda ("chardev: add helper function to register
char devs with a struct device")'), use it instead of cdev add/del().
Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.2.Idde68b05b88d4a2e6e54766c653f3a6d9e419ce6@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct rpmsg_ctrldev contains a struct cdev. The current code frees
the rpmsg_ctrldev struct in rpmsg_ctrldev_release_device(), but the
cdev is a managed object, therefore its release is not predictable
and the rpmsg_ctrldev could be freed before the cdev is entirely
released, as in the backtrace below.
The cdev_device_add/del() API was created to address this issue (see
commit '233ed09d7fda ("chardev: add helper function to register char
devs with a struct device")'), use it instead of cdev add/del().
Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Signed-off-by: Sujit Kautkar <sujitka@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.1.Iaac908f3e3149a89190ce006ba166e2d3fd247a3@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.
Fix this by always allocating last queue in PF queue pile
for a flow director VSI.
Fixes: 41c445ff0f48 ("i40e: main driver core") Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.
Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.
Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"
Fixes: 7daa6bf3294e ("i40e: driver core headers") Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.
Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.
Fixes: 1fa51a650e1d ("i40e: Add delay after EMP reset for firmware to recover") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by: David S. Miller <davem@davemloft.net>
[ backport to 4.19 ] Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.
Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org> Reported-by: DocMAX <mail@vacharakis.de> Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.) Cc: stable <stable@vger.kernel.org> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes") Cc: stable@vger.kernel.org Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Reviewed-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:
Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com> CC: stable@vger.kernel.org Fixes: 52ebea749aae ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we fail to expand inode from inline format to a normal format, we
restore inode to contain the original inline formatting but we forgot to
set i_lenAlloc back. The mismatch between i_lenAlloc and i_size was then
causing further problems such as warnings and lost data down the line.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com> CC: stable@vger.kernel.org Fixes: 7e49b6f2480c ("udf: Convert UDF to new truncate calling sequence") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") Cc: <stable@vger.kernel.org> #2.6.32+ Suggested-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if z/VM guest is allowed to retrieve hypervisor performance
data globally for all guests (privilege class B) the query is formed in a
way to include all guests but the group name is left empty. This leads to
that z/VM guests which have access control group set not being included
in the results (even local vm).
Change the query group identifier from empty to "any" to retrieve
information about all guests from any groups (or without a group set).
Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.
Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.
A task can end up indefinitely sleeping in do_select() ->
poll_schedule_timeout() when the following race happens:
TASK1 (thread1) TASK2 TASK1 (thread2)
do_select()
setup poll_wqueues table
with 'fd'
write data to 'fd'
pollwake()
table->triggered = 1
closes 'fd' thread1 is
waiting for
poll_schedule_timeout()
- sees table->triggered
table->triggered = 0
return -EINTR
loop back in do_select()
But at this point when TASK1 loops back, the fdget() in the setup of
poll_wqueues fails. So now so we never find 'fd' is ready for reading
and sleep in poll_schedule_timeout() indefinitely.
Treat an fd that got closed as a fd on which some event happened. This
makes sure cannot block indefinitely in do_select().
Another option would be to return -EBADF in this case but that has a
potential of subtly breaking applications that excercise this behavior
and it happens to work for them. So returning fd as active seems like a
safer choice.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to clear all of the bridge private skb variables as they can be
stale due to the packet being recirculated through the stack and then
transmitted through the bridge device. Similar memset is already done on
bridge's input. We've seen cases where proxyarp_replied was 1 on routed
multicast packets transmitted through the bridge to ports with neigh
suppress which were getting dropped. Same thing can in theory happen with
the port isolation bit as well.
Fixes: 821f1b21cabb ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Huang Guobin <huangguobin4@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5d069dbe8aaf ("fuse: fix bad inode") replaced make_bad_inode()
in fuse_iget() with a private implementation fuse_make_bad().
The private implementation fails to remove the bad inode from inode
cache, so the retry loop with iget5_locked() finds the same bad inode
and marks it bad forever.
Jan Kara's analysis of the syzbot report (edited):
The reproducer opens a directory on FUSE filesystem, it then attaches
dnotify mark to the open directory. After that a fuse_do_getattr() call
finds that attributes returned by the server are inconsistent, and calls
make_bad_inode() which, among other things does:
inode->i_mode = S_IFREG;
This then confuses dnotify which doesn't tear down its structures
properly and eventually crashes.
Avoid calling make_bad_inode() on a live inode: switch to a private flag on
the fuse inode. Also add the test to ops which the bad_inode_ops would
have caught.
This bug goes back to the initial merge of fuse in 2.6.14...
Reported-by: syzbot+f427adf9324b92652ccc@syzkaller.appspotmail.com Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Jan Kara <jack@suse.cz> Cc: <stable@vger.kernel.org>
[bwh: Backported to 4.19:
- Drop changes in fuse_dir_fsync(), fuse_readahead(), fuse_evict_inode()
- In fuse_get_link(), return ERR_PTR(-EIO) for bad inodes
- Convert some additional calls to is_bad_inode()
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 24 Jan 2022 15:11:18 +0000 (16:11 +0100)]
mips,s390,sh,sparc: gup: Work around the "COW can break either way" issue
In Linux 4.14 and 4.19 these architectures still have their own
implementations of get_user_pages_fast(). These also need to force
the write flag on when taking the fast path.
Fixes: 407faed92b4a ("gup: document and work around "COW can break either way" issue") Fixes: 5e24029791e8 ("gup: document and work around "COW can break either way" issue") Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
[<miquel.raynal@bootlin.com>: Fixed the title] Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Link: https://lore.kernel.org/linux-mtd/774a92693f311e7de01e5935e720a179fb1b2468.1616635406.git.ytc-mb-yfuruyama7@kioxia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns negative error number instead 0 on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
Fixes: 115978859272 ("i825xx: Move the Intel 82586/82593/82596 based drivers") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dtx_diff suggests to use <(...) syntax to pipe two inputs into it, but
this has never worked: The /proc/self/fds/... paths passed by the shell
will fail the `[ -f "${dtx}" ] && [ -r "${dtx}" ]` check in compile_to_dts,
but even with this check removed, the function cannot work: hexdump will
eat up the DTB magic, making the subsequent dtc call fail, as a pipe
cannot be rewound.
Simply remove this broken example, as there is already an alternative one
that works fine.
Fixes: 10eadc253ddf ("dtc: create tool to diff device trees") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Frank Rowand <frank.rowand@sony.com> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220113081918.10387-1-matthias.schiffer@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq_optional()'s
call and blithely passes the negative error codes to devm_request_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL.
Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8562056f267d ("net: bcmgenet: request Wake-on-LAN interrupt") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b765b79e9a ("htb: improved accuracy at high rates") broke
"overhead X", "linklayer atm" and "mpu X" attributes.
"overhead X" and "linklayer atm" have already been fixed. This restores
the "mpu X" handling, as might be used by DOCSIS or Ethernet shaping:
tc class add ... htb rate X overhead 4 mpu 64
The code being fixed is used by htb, tbf and act_police. Cake has its
own mpu handling. qdisc_calculate_pkt_len still uses the size table
containing values adjusted for mpu by user space.
iproute2 tc has always passed mpu into the kernel via a tc_ratespec
structure, but the kernel never directly acted on it, merely stored it
so that it could be read back by `tc class show`.
Rather, tc would generate length-to-time tables that included the mpu
(and linklayer) in their construction, and the kernel used those tables.
Since v3.7, the tables were no longer used. Along with "mpu", this also
broke "overhead" and "linklayer" which were fixed in 01cb71d2d47b
("net_sched: restore "overhead xxx" handling", v3.10) and 8a8e3d84b171
("net_sched: restore "linklayer atm" handling", v3.11).
"overhead" was fixed by simply restoring use of tc_ratespec::overhead -
this had originally been used by the kernel but was initially omitted
from the new non-table-based calculations.
"linklayer" had been handled in the table like "mpu", but the mode was
not originally passed in tc_ratespec. The new implementation was made to
handle it by getting new versions of tc to pass the mode in an extended
tc_ratespec, and for older versions of tc the table contents were analysed
at load time to deduce linklayer.
As "mpu" has always been given to the kernel in tc_ratespec,
accompanying the mpu-based table, we can restore system functionality
with no userspace change by making the kernel act on the tc_ratespec
value.
Fixes: 56b765b79e9a ("htb: improved accuracy at high rates") Signed-off-by: Kevin Bracey <kevin@bracey.fi> Cc: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Vimalkumar <j.vimal@gmail.com> Link: https://lore.kernel.org/r/20220112170210.1014351-1-kevin@bracey.fi Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware channel next descriptor view structure contains just
fields of 32 bits, while dma_addr_t can be of type u64 or u32
depending on CONFIG_ARCH_DMA_ADDR_T_64BIT. Force u32 to comply with
what the hardware expects.
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove
at_xdmac_start_xfer() from at_xdmac_tx_submit(). Clients of at_xdmac that
assume that tx_submit() starts the transfer must be updated and call
dma_async_issue_pending() if they miss to call it (one example is
atmel_serial).
As the at_xdmac_start_xfer() is now called only from
at_xdmac_advance_work() when !at_xdmac_chan_is_enabled(), the
at_xdmac_chan_is_enabled() check is no longer needed in
at_xdmac_start_xfer(), thus remove it.
Mask the ECN bits before calling ip_route_output_ports(). The tos
variable might be passed directly from an IPv4 header, so it may have
the last ECN bit set. This interferes with the route lookup process as
ip_route_output_key_hash() interpretes this bit specially (to restrict
the route scope).
When under stress, cleanup_net() can have to dismantle
netns in big numbers. ops_exit_list() currently calls
many helpers [1] that have no schedule point, and we can
end up with soft lockups, particularly on hosts
with many cpus.
Even for moderate amount of netns processed by cleanup_net()
this patch avoids latency spikes.
[1] Some of these helpers like fib_sync_up() and fib_sync_down_dev()
are very slow because net/ipv4/fib_semantics.c uses host-wide hash tables,
and ifindex is used as the only input of two hash functions.
ifindexes tend to be the same for all netns (lo.ifindex==1 per instance)
This will be fixed in a separate patch.
Fixes: 72ad937abd0a ("net: Add support for batching network namespace cleanups") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the latest stable kernel versions the rtc on the PXA based
Zaurus does not work, when booting I see the following kernel messages:
pxa-rtc pxa-rtc: failed to find rtc clock source
pxa-rtc pxa-rtc: Unable to init SA1100 RTC sub-device
pxa-rtc: probe of pxa-rtc failed with error -2
hctosys: unable to open rtc device (rtc0)
I think this is because commit f2997775b111 ("rtc: sa1100: fix possible
race condition") moved the allocation of the rtc_device struct out of
sa1100_rtc_init and into sa1100_rtc_probe. This means that pxa_rtc_probe
also needs to do allocation for the rtc_device struct, otherwise
sa1100_rtc_init will try to dereference a null pointer. This patch adds
that allocation by copying how sa1100_rtc_probe in
drivers/rtc/rtc-sa1100.c does it; after the IRQs are set up a managed
rtc_device is allocated.
I've tested this patch with `qemu-system-arm -machine akita` and with a
real Zaurus SL-C1000 applied to 4.19, 5.4, and 5.10.
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252dca9 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_unix_gc() reads unix_tot_inflight & gc_in_progress
without synchronization.
Adds READ_ONCE()/WRITE_ONCE() and their associated comments
to better document the intent.
BUG: KCSAN: data-race in unix_inflight / wait_for_unix_gc
write to 0xffffffff86e2b7c0 of 4 bytes by task 9380 on cpu 0:
unix_inflight+0x1e8/0x260 net/unix/scm.c:63
unix_attach_fds+0x10c/0x1e0 net/unix/scm.c:121
unix_scm_to_skb net/unix/af_unix.c:1674 [inline]
unix_dgram_sendmsg+0x679/0x16b0 net/unix/af_unix.c:1817
unix_seqpacket_sendmsg+0xcc/0x110 net/unix/af_unix.c:2258
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2549
__do_sys_sendmmsg net/socket.c:2578 [inline]
__se_sys_sendmmsg net/socket.c:2575 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2575
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffffffff86e2b7c0 of 4 bytes by task 9375 on cpu 1:
wait_for_unix_gc+0x24/0x160 net/unix/garbage.c:196
unix_dgram_sendmsg+0x8e/0x16b0 net/unix/af_unix.c:1772
unix_seqpacket_sendmsg+0xcc/0x110 net/unix/af_unix.c:2258
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2549
__do_sys_sendmmsg net/socket.c:2578 [inline]
__se_sys_sendmmsg net/socket.c:2575 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2575
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000002 -> 0x00000004
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 9375 Comm: syz-executor.1 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
projects / users / dwmw2 / linux.git / log