In aacraid's ioctl_send_fib() we do two fetches from userspace, one the
get the fib header's size and one for the fib itself. Later we use the
size field from the second fetch to further process the fib. If for some
reason the size from the second fetch is different than from the first
fix, we may encounter an out-of- bounds access in aac_fib_send(). We
also check the sender size to insure it is not out of bounds. This was
reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was
assigned CVE-2016-6480.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Fixes: 7c00ffa31 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)' Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
trace_hardirqs_on_caller() in lockdep.c expects to be called before, not
after interrupts are actually enabled.
The following comment in kernel/locking/lockdep.c substantiates this
claim:
"
/*
* We're enabling irqs and according to our state above irqs weren't
* already enabled, yet we find the hardware thinks they are in fact
* enabled.. someone messed up their IRQ state tracing.
*/
"
An example can be found in include/linux/irqflags.h:
do { trace_hardirqs_on(); raw_local_irq_enable(); } while (0)
Without this change, we hit the following DEBUG_LOCKS_WARN_ON.
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
ARC architecture has 2 instruction sets: ARCompact/ARCv2.
While same gcc supports compiling for either (using appropriate toggles),
we can't use the same toolchain to build kernel because libgcc needs
to be unique and the toolchian (uClibc based) is not multilibed.
uClibc toolchain is convenient since it allows all userspace and
kernel to be built with a single install for an ISA.
This however means 2 gnu installs (with same triplet prefix) are needed
for building for 2 ISA and need to be in PATH.
As developers we keep switching the builds, but would occassionally fail
to update the PATH leading to usage of wrong tools. And this would only
show up at the end of kernel build when linking incompatible libgcc.
So the initial solution was to have gcc define a special preprocessor macro
DEFAULT_CPU_xxx which is unique for default toolchain configuration.
Claudiu proposed using grep for an existing preprocessor macro which is
again uniquely defined per ISA.
Cc: Michal Marek <mmarek@suse.cz> Suggested-by: Claudiu Zissulescu <claziss@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround for bug:
https://bugs.freedesktop.org/show_bug.cgi?id=97460
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When looking up the connector type make sure the index
is valid. Avoids a later crash if we read past the end
of the array.
Workaround for bug:
https://bugs.freedesktop.org/show_bug.cgi?id=97460
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug seems to be present for a very long time.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GART aperture size can be bigger than 4GB. Therefore the offset
used in amdgpu_gart_bind and amdgpu_gart_unbind must be 64-bit.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using CONFIG_DEBUG_ATOMIC_SLEEP, the scheduler nicely points out
that we're calling sleeping primitives within the wait_event loop, which
means we might clobber the task state:
[ 10.831289] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffc00026b610>]
[ 10.845531] ------------[ cut here ]------------
[ 10.850161] WARNING: at kernel/sched/core.c:7630
...
[ 12.164333] ---[ end trace 45409966a9a76438 ]---
[ 12.168942] Call trace:
[ 12.171391] [<ffffffc00024ed44>] __might_sleep+0x64/0x90
[ 12.176699] [<ffffffc000954774>] mutex_lock_nested+0x50/0x3fc
[ 12.182440] [<ffffffc0007b9424>] iio_kfifo_buf_data_available+0x28/0x4c
[ 12.189043] [<ffffffc0007b76ac>] iio_buffer_ready+0x60/0xe0
[ 12.194608] [<ffffffc0007b7834>] iio_buffer_read_first_n_outer+0x108/0x1a8
[ 12.201474] [<ffffffc000370d48>] __vfs_read+0x58/0x114
[ 12.206606] [<ffffffc000371740>] vfs_read+0x94/0x118
[ 12.211564] [<ffffffc0003720f8>] SyS_read+0x64/0xb4
[ 12.216436] [<ffffffc000203cb4>] el0_svc_naked+0x24/0x28
To avoid this, we should (a la https://lwn.net/Articles/628628/) use the
wait_woken() function, which avoids the nested sleeping while still
handling races between waiting / wake-events.
Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
9642d18eee2c ("nohz: Affine unpinned timers to housekeepers")'
intended to affine unpinned timers to housekeepers:
unpinned timers(full dynaticks, idle) => nearest busy housekeepers(otherwise, fallback to any housekeepers)
unpinned timers(full dynaticks, busy) => nearest busy housekeepers(otherwise, fallback to any housekeepers)
unpinned timers(houserkeepers, idle) => nearest busy housekeepers(otherwise, fallback to itself)
However, the !idle_cpu(i) && is_housekeeping_cpu(cpu) check modified the
intention to:
unpinned timers(full dynaticks, idle) => any housekeepers(no mattter cpu topology)
unpinned timers(full dynaticks, busy) => any housekeepers(no mattter cpu topology)
unpinned timers(housekeepers, idle) => any busy cpus(otherwise, fallback to any housekeepers)
This patch fixes it by checking if there are busy housekeepers nearby,
otherwise falls to any housekeepers/itself. After the patch:
unpinned timers(full dynaticks, idle) => nearest busy housekeepers(otherwise, fallback to any housekeepers)
unpinned timers(full dynaticks, busy) => nearest busy housekeepers(otherwise, fallback to any housekeepers)
unpinned timers(housekeepers, idle) => nearest busy housekeepers(otherwise, fallback to itself)
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[ Fixed the changelog. ] Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Fixes: 'commit 9642d18eee2c ("nohz: Affine unpinned timers to housekeepers")' Link: http://lkml.kernel.org/r/1462344334-8303-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The called of_graph_get_next_endpoint() already decrements the refcount
of the prev node, so it is wrong to do it again in the calling function.
Use the for_each_endpoint_of_node() helper to interate through the
endpoint OF nodes, which already does the right thing and simplifies
the code a bit.
Fixes: 8ccd0d0ca041
(of: add helper for getting endpoint node of specific identifiers) Reported-by: David Jander <david@protonic.nl> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is in a status where CIO has killed all I/O by itself the
interrupt for a clear request may not contain an irb to determine the
clear function. Instead it contains an error pointer -EIO.
This was ignored by the DASD int_handler leading to a hanging device
waiting for a clear interrupt.
Handle -EIO error pointer correctly for requests that are clear pending and
treat the clear as successful.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function amd_gpio_irq_enable() and
amd_gpio_direction_input(), remove the code which is setting
the default de-bounce time to 2.75ms.
The driver code shall use the same settings as specified in
BIOS. Any default assignment impacts TouchPad behaviour when
the LevelTrig is set to EDGE FALLING.
The disable_bypass cmdline option changes the SMMUv3 driver to put down
faulting stream table entries by default, as opposed to bypassing
transactions from unconfigured devices.
In this mode of operation, it is entirely expected to see aborting
entries in the stream table if and when we come to installing a valid
translation, so don't trigger a BUG() as a result of misdiagnosing these
entries as stream table corruption.
Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices") Tested-by: Robin Murphy <robin.murphy@arm.com> Reported-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the unlikely event of a global command queue error, the ARM SMMUv3
driver attempts to convert the problematic command into a CMD_SYNC and
resume the command queue. Unfortunately, this code is pretty badly
broken:
1. It uses the index into the error string table as the CMDQ index,
so we probably read the wrong entry out of the queue
2. The arguments to queue_write are the wrong way round, so we end up
writing from the queue onto the stack.
These happily cancel out, so the kernel is likely to stay alive, but
the command queue will probably fault again when we resume.
This patch fixes the error handling code to use the correct queue index
and write back the CMD_SYNC to the faulting entry.
Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices") Reported-by: Diwakar Subraveti <Diwakar.Subraveti@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the limitations of having to wait until we see a device's DMA
restrictions before we know how we want an IOVA domain initialised,
there is a window for error if a DMA ops domain is allocated but later
freed without ever being used. In that case, init_iova_domain() was
never called, so calling put_iova_domain() from iommu_put_dma_cookie()
ends up trying to take an uninitialised lock and crashing.
Make things robust by skipping the call unless the IOVA domain actually
has been initialised, as we probably should have done from the start.
Fixes: 0db2e5d18f76 ("iommu: Implement common IOMMU ops for DMA mapping") Reported-by: Nate Watterson <nwatters@codeaurora.org> Reviewed-by: Nate Watterson <nwatters@codeaurora.org> Tested-by: Nate Watterson <nwatters@codeaurora.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udriver struct allocated by kzalloc() will not be freed
if usb_register() and next calls fail. This patch fixes this
by adding one more step with kfree(udriver) in error path.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values. This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.
This issue was first discovered and tests were conducted by Jake Lamberson
<jake.lamberson1@gmail.com>, an intern working for Rosie Hall.
This patch fixes an issue that isochronous transfer's data is possible to
be lost as a workaround. Since this driver uses a workqueue to start
the dmac, the transfer is possible to be delayed when system load is high.
This patch fixes an issue that unexpected BRDY interruption happens
when the usb_ep_{enable,disable}() are called with different direction.
In this case, the driver will cause the following message:
This issue causes the followings:
1) A pipe is enabled as transmission
2) The pipe sent a data
3) The pipe is disabled and re-enabled as reception.
4) The pipe got a queue
Since the driver doesn't clear the BRDYSTS flags after 2) above, the issue
happens. If we add such clearing the flags into the driver, the code will
become complicate. So, this patch clears the BRDYSTS flag of reception in
usbhsg_ep_enable() to avoid complicate.
The locking in hub_activate() is not adequate to provide full mutual
exclusion with hub_quiesce(). The subroutine locks the hub's
usb_interface, but the callers of hub_quiesce() (such as
hub_pre_reset() and hub_event()) hold the lock to the hub's
usb_device.
This patch changes hub_activate() to make it acquire the same lock as
those other routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early-exit pathway in hub_activate, added by commit e50293ef9775
("USB: fix invalid memory access in hub_activate()") needs
improvement. It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.
This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine. It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef9775 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
Fixes: e50293ef9775 ("USB: fix invalid memory access in hub_activate()") Reported-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Reported-by: Brian E Rogers <brian.e.rogers@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to generate shared descriptors for AEAD, the authentication size
needs to be known. However, there is no imposed order of calling .setkey,
.setauthsize callbacks.
Thus, in case authentication size is not known at .setkey time, defer it
until .setauthsize is called.
The authsize != 0 check was incorrectly removed when converting the driver
to the new AEAD interface.
Fixes: 479bcc7c5b9e ("crypto: caam - Convert authenc to new AEAD interface") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few things missed by the conversion to the
new AEAD interface:
1 - echainiv(authenc) encrypt shared descriptor
The shared descriptor is incorrect: due to the order of operations,
at some point in time MATH3 register is being overwritten.
2 - buffer used for echainiv(authenc) encrypt shared descriptor
Encrypt and givencrypt shared descriptors (for AEAD ops) are mutually
exclusive and thus use the same buffer in context state: sh_desc_enc.
However, there's one place missed by s/sh_desc_givenc/sh_desc_enc,
leading to errors when echainiv(authenc(...)) algorithms are used:
DECO: desc idx 14: Header Error. Invalid length or parity, or
certain other problems.
While here, also fix a typo: dma_mapping_error() is checking
for validity of sh_desc_givenc_dma instead of sh_desc_enc_dma.
Fixes: 479bcc7c5b9e ("crypto: caam - Convert authenc to new AEAD interface") Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 6de62f15b581 ("crypto: algif_hash - Require setkey before
accept(2)"), the AF_ALG interface requires userspace to provide a key
to any algorithm that has a setkey method. However, the non-HMAC
algorithms are not keyed, so setting a key is unnecessary.
Fix this by removing the setkey method from the non-keyed hash
algorithms.
Fixes: 6de62f15b581 ("crypto: algif_hash - Require setkey before accept(2)") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7c2 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts" Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru> Reported-by: Matthias Prager <linux@matthiasprager.de> Reported-by: Jason Taylor <jason.taylor@simplivity.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: linux-pci@vger.kernel.org Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e41f501d3912 ("vmlinux.lds: account for destructor sections")
added '.text.exit' to EXIT_TEXT which is discarded at link time by default.
This breaks compilation of UML:
`.text.exit' referenced in section `.fini_array' of
/usr/lib/gcc/x86_64-linux-gnu/6/../../../x86_64-linux-gnu/libc.a(sdlerror.o):
defined in discarded section `.text.exit' of
/usr/lib/gcc/x86_64-linux-gnu/6/../../../x86_64-linux-gnu/libc.a(sdlerror.o)
Apparently UML doesn't want to discard exit text, so let's place all EXIT_TEXT
sections in .exit.text.
Fixes: e41f501d3912 ("vmlinux.lds: account for destructor sections") Reported-by: Stefan Traby <stefan@hello-penguin.com> Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 8.4.7.1 section of ACPI 6.1 specification, if the platform
supports CPPC, the _CPC object must exist under all processor objects.
If cpc_desc_ptr pointer is invalid on any CPUs, acpi_get_psd_map()
should return error and CPPC cpufreq driver can not be registered.
Signed-off-by: Hoan Tran <hotran@apm.com> Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Baytrail eMMC/SD/SDIO host controllers have been known to
hang. A change to a hardware setting has been found to
reduce the occurrence of such hangs. This patch ensures
the correct setting.
This patch applies cleanly to v4.4+. It could go to
earlier kernels also, so I will send backports to the
stable list in due course.
Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI
config space addresses above 0x600 can cause the NFP to generate PCIe
completion timeouts.
Limit the NFP4000's PF's config space size to 0x600 bytes as is already
done for the NFP6000.
The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
If a device quirk modifies the pci_dev->cfg_size to be less than
PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256),
the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE.
Allow sysfs access to config space up to cfg_size, even if the device
doesn't support the entire 4096-byte PCIe config space.
Note that pci_read_config() and pci_write_config() limit access to
dev->cfg_size even though pcie_config_attr contains 4096 (the maximum
size).
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com>
[bhelgaas: more changelog edits] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unmapping the registers on reset or shutdown is not necessary. Keeping
the mapping simplifies reset handling.
This was backported to 4.4 stable tree because it prevents a race
between the reset_work and the shutdown hook, that may provoke the Oops
below, in the nvme_wait_ready function.
The Oops is easily reproducible on systems that will kexec/reboot
immediately after booting, which is actually the common use case for
kexec based bootloaders, like Petitboot. This patch removes the
unnecessary early unmapping of the PCI configuration in the shutdown
hook, allowing a proper handling of the reset work.
For SKL and later Intel chips, we control the power well per codec
basis via link_power callback since the commit [03b135cebc47: ALSA:
hda - remove dependency on i915 power well for SKL].
However, there are a few exceptional cases where the gfx registers are
accessed from the audio driver: namely the wakeup override bit
toggling at (both system and runtime) resume. This seems causing a
kernel warning when accessed during the power well down (and likely
resulting in the bogus register accesses).
This patch puts the proper power up / down sequence around the resume
code so that the wakeup bit is fiddled properly while the power is
up. (The other callback, sync_audio_rate, is used only in the PCM
callback, so it's guaranteed in the power-on.)
Also, by this proper power up/down, the instantaneous flip of wakeup
bit in the resume callback that was introduced by the commit
[033ea349a7cd: ALSA: hda - Fix Skylake codec timeout] becomes
superfluous, as snd_hdac_display_power() already does it. So we can
clean it up together.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214 Fixes: 03b135cebc47 ('ALSA: hda - remove dependency on i915 power well for SKL') Cc: <stable@vger.kernel.org> # v4.2+ Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...defines the layout of the block window status register. For the July
2016 version of the spec linked to above, this happens in Figure 4 on
page 26.
The only bits defined in this spec are bits 31, 5, 4, 2, 1 and 0. The
rest of the bits in the status register are reserved, and there is a
warning following the diagram that says:
Note: The driver cannot assume the value of the RESERVED bits in the
status register are zero. These reserved bits need to be masked off, and
the driver must avoid checking the state of those bits.
This change ensures that for hardware implementations that set these
reserved bits in the status register, the driver won't incorrectly fail the
block I/Os.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to successfully decode Intel PT traces, context switch events
are needed from the moment the trace starts. Currently that is ensured
by using the 'immediate' flag which enables the switch event when it is
opened.
However, since commit 86c2786994bd ("perf intel-pt: Add support for
PERF_RECORD_SWITCH") that might not always happen. When tracing
system-wide the context switch event is added to the tracking event
which was not set as 'immediate'. Change that so it is.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Fixes: 86c2786994bd ("perf intel-pt: Add support for PERF_RECORD_SWITCH") Link: http://lkml.kernel.org/r/1471245784-22580-1-git-send-email-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple cases in vfio_pci_set_ctx_trigger_single() where
we assume we can safely read from our data pointer without actually
checking whether the user has passed any data via the count field.
VFIO_IRQ_SET_DATA_NONE in particular is entirely broken since we
attempt to pull an int32_t file descriptor out before even checking
the data type. The other data types assume the data pointer contains
one element of their type as well.
In part this is good news because we were previously restricted from
doing much sanitization of parameters because it was missed in the
past and we didn't want to break existing users. Clearly DATA_NONE
is completely broken, so it must not have any users and we can fix
it up completely. For DATA_BOOL and DATA_EVENTFD, we'll just
protect ourselves, returning error when count is zero since we
previously would have oopsed.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Reported-by: Chris Thompson <the_cartographer@hotmail.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the indirect buffers feature, 'desc' is allocated in
virtqueue_add() but isn't freed before leaving on a ring full error,
causing a memory leak.
For example, it seems rather clear that this can trigger
with virtio net if mergeable buffers are not used.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for arm64 at all even though ARCH_DLINFO will contain one NEW_AUX_ENT
for the VDSO address.
This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which arm64 doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.
Fixes: f668cd1673aa ("arm64: ELF definitions") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VF0610 does not support reading the sample rate which leads to many
lines of "cannot get freq at ep 0x82". This patch adds the USB ID
(0x041E:4080) to snd_usb_get_sample_rate_quirk() list.
In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.
At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.
On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.
On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.
Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.
Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to have simultaneous upcalls for the same UIDs but
different GSS service. In that case, we need to allow for the
upcall to gssd to proceed so that not the same context is used
by two different GSS services. Some servers lock the use of context
to the GSS service.
If the connect attempt immediately fails with an EADDRNOTAVAIL error, then
that means our choice of source port number was bad.
This error is expected when we set the SO_REUSEPORT socket option and we
have 2 sockets sharing the same source and destination address and port
combinations.
The unit tests crash when hotplug races the previous probe. This race
requires that the loading of the nfit_test module be terminated with
SIGTERM, and the module to be unloaded while the ars scan is still
running.
In contrast to the normal nfit driver, the unit test calls
acpi_nfit_init() twice to simulate hotplug, whereas the nominal case
goes through the acpi_nfit_notify() event handler. The
acpi_nfit_notify() path is careful to flush the previous region
registration before servicing the hotplug event. The unit test was
missing this guarantee.
Since instruction decoder now supports EVEX-encoded instructions, two fixes
are needed to correctly handle them in uprobes.
Extended bits for MODRM.rm field need to be sanitized just like we do it
for VEX3, to avoid encoding wrong register for register-relative access.
EVEX has _two_ extended bits: b and x. Theoretically, EVEX.x should be
ignored by the CPU (since GPRs go only up to 15, not 31), but let's be
paranoid here: proper encoding for register-relative access
should have EVEX.x = 1.
Secondly, we should fetch vex.vvvv for EVEX too.
This is now super easy because instruction decoder populates
vex_prefix.bytes[2] for all flavors of (e)vex encodings, even for VEX2.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jim Keniston <jkenisto@us.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: linux-kernel@vger.kernel.org Fixes: 8a764a875fe3 ("x86/asm/decoder: Create artificial 3rd byte for 2-byte VEX") Link: http://lkml.kernel.org/r/20160811154521.20469-1-dvlasenk@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usually current->mm (and therefore mm->pgd) stays the same during the
lifetime of a task so it does not matter if a task gets preempted during
the read and write of the CR3.
But then, there is this scenario on x86-UP:
TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by:
At this point current->mm is NULL but current->active_mm still points to
the "old" mm.
Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its
own mm so CR3 has changed.
Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's
mm and so CR3 remains unchanged. Once taskA gets active it continues
where it was interrupted and that means it writes its old CR3 value
back. Everything is fine because userland won't need its memory
anymore.
Now the fun part:
Let's preempt taskA one more time and get back to taskB. This
time switch_mm() won't do a thing because oldmm (->active_mm)
is the same as mm (as per context_switch()). So we remain
with a bad CR3 / PGD and return to userland.
The next thing that happens is handle_mm_fault() with an address for
the execution of its code in userland. handle_mm_fault() realizes that
it has a PTE with proper rights so it returns doing nothing. But the
CPU looks at the wrong PGD and insists that something is wrong and
faults again. And again. And one more time…
This pagefault circle continues until the scheduler gets tired of it and
puts another task on the CPU. It gets little difficult if the task is a
RT task with a high priority. The system will either freeze or it gets
fixed by the software watchdog thread which usually runs at RT-max prio.
But waiting for the watchdog will increase the latency of the RT task
which is no good.
Fix this by disabling preemption across the critical code section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de
[ Prettified the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. If a module signing key is used for
multiple ABI-incompatible kernels, the modules need to include enough
version information to distinguish them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signing a module should only make it trusted by the specific kernel it
was built for, not anything else. Loading a signed module meant for a
kernel with a different ABI could have interesting effects.
Therefore, treat all signatures as invalid when a module is
force-loaded.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
As per code flow s3c_rtc_setfreq() will get called with rtc clock disabled
and in set_freq we perform h/w registers read/write, which results in a
kernel crash on exynos7 platform while probing rtc driver.
Below is code flow:
s3c_rtc_probe()
clk_prepare_enable(info->rtc_clk) // rtc clock enabled
s3c_rtc_gettime() // will enable clk if not done, and disable it upon exit
s3c_rtc_setfreq() //then this will be called with clk disabled
This patch take cares of such issue by adding s3c_rtc_{enable/disable}_clk in
s3c_rtc_setfreq().
The lpfc_sli4_scmd_to_wqidx_distr() function expects the scsi_cmnd
'lpfc_cmd->pCmd' not to be null, and point to the midlayer command.
That's not true in the .eh_(device|target|bus)_reset_handler path,
because lpfc_send_taskmgmt() sends commands not from the midlayer, so
does not set 'lpfc_cmd->pCmd'.
That is true in the .queuecommand path because lpfc_queuecommand()
stores the scsi_cmnd from midlayer in lpfc_cmd->pCmd; and lpfc_cmd is
stored by lpfc_scsi_prep_cmnd() in piocbq->context1 -- which is passed
to lpfc_sli4_scmd_to_wqidx_distr() as lpfc_cmd parameter.
This problem can be hit on SCSI EH, and immediately with sg_reset.
These 2 test-cases demonstrate the problem/fix with next-20160601.
Fixes: 8b0dff14164d ("lpfc: Add support for using block multi-queue") Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this commit, using system workqueue causes that the maximum parallel
executions of _Qxx can exceed 255. This violates the method reentrancy
limit in ACPICA and generates the following error log:
ACPI Error: Method reached maximum reentrancy limit (255) (20150818/dsmethod-341)
This patch creates a seperate workqueue and limits the number of parallel
_Qxx evaluations down to a configurable value (can be tuned against number
of online CPUs).
Since EC events are handled after driver probe, we can create the workqueue
in acpi_ec_init().
Fixes: 02b771b64b73 (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations) Link: https://bugzilla.kernel.org/show_bug.cgi?id=135691 Reported-and-tested-by: Helen Buus <ubuntu@hbuus.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Merrifield platform several PCI devices have a bogus configuration,
i.e. the IRQ0 had been assigned to few of them. These are PCI root bridge,
eMMC0, HS UART common registers, PWM, and HDMI. The actual interrupt line can
be allocated to one device exclusively, in our case to eMMC0, the rest should
cope without it and basically known drivers for them are not using interrupt
line at all.
Rework IRQ0 workaround, which was previously done to avoid conflict between
eMMC0 and HS UART common registers, to behave differently based on the device
in question, i.e. allocate interrupt line to eMMC0, but silently skip interrupt
allocation for the rest except HS UART common registers which are not used
anyway. With this rework IOSF MBI driver in particular would be used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 39d9b77b8deb ("x86/pci/intel_mid_pci: Work around for IRQ0 assignment") Link: http://lkml.kernel.org/r/1465842481-136852-1-git-send-email-andriy.shevchenko@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At first, we prefer to use mips clockevent device, so we decrease the
rating of hpet clockevent device.
For hpet, if HPET_MIN_PROG_DELTA (minimum delta of hpet programming) is
too small and HPET_MIN_CYCLES (threshold of -ETIME checking) is too
large, then hpet_next_event() can easily return -ETIME. After commit c6eb3f70d44828 ("hrtimer: Get rid of hrtimer softirq") this will cause
a RCU stall.
So, HPET_MIN_PROG_DELTA must be sufficient that we don't re-trip the
-ETIME check -- if we do, we will return -ETIME, forward the next event
time, try to set it, return -ETIME again, and basically lock the system
up. Meanwhile, HPET_MIN_CYCLES doesn't need to be too large, 16 cycles
is enough.
This solution is similar to commit f9eccf24615672 ("clocksource/drivers
/vt8500: Increase the minimum delta").
By the way, this patch ensures hpet count/compare to be 32-bit long.
Some ASUS laptops were shipped with touchpads that require to be woken up
first, before trying to switch them into absolute reporting mode, otherwise
touchpad would fail to work while flooding the logs with:
elan_i2c i2c-ELAN1000:00: invalid report id data (1)
Among affected devices are Asus E202SA, N552VW, X456UF, UX305CA, and
others. We detect such devices by checking the IC type and product ID
numbers and adjusting order of operations accordingly.
If a Simple command is sent with a failure, target_setup_cmd_from_cdb
returns with TCM_UNSUPPORTED_SCSI_OPCODE or TCM_INVALID_CDB_FIELD.
So in the cases where target_setup_cmd_from_cdb returns an error, we
never get far enough to call target_execute_cmd to increment simple_cmds.
Since simple_cmds isn't incremented, the result of the failure from
target_setup_cmd_from_cdb causes transport_generic_request_failure to
decrement simple_cmds, due to call to transport_complete_task_attr.
With this dev->simple_cmds or dev->dev_ordered_sync is now -1, not 0.
So when a subsequent command with an Ordered Task is sent, it causes
a hang, since dev->simple_cmds is at -1.
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
max_discard_sectors only 32bits, and some non scsi backend
devices will set this to the max 0xffffffff, so we can end up
overflowing during the max_unmap_lba_count calculation.
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
which can result in extra discards being sent to due the overflow
causing max_unmap_lba_count to be smaller than what the backing
device can actually support.
Signed-off-by: Mike Christie <mchristi@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a race in iscsit_release_commands_from_conn() ->
iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1,
where CMD_T_FABRIC_STOP could end up being set after the final
kref_put() is called from core_tmr_abort_task() context.
This results in transport_generic_free_cmd() blocking indefinately
on se_cmd->cmd_wait_comp, because the target_release_cmd_kref()
check for CMD_T_FABRIC_STOP returns false.
To address this bug, make iscsit_release_commands_from_conn()
do list_splice and set CMD_T_FABRIC_STOP early while holding
iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only
remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been
set.
Finally in target_release_cmd_kref(), only honor fabric_stop
if CMD_T_ABORTED has been set.
Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During transport_generic_free_cmd() with a concurrent TMR
ABORT_TASK and shutdown CMD_T_FABRIC_STOP bit set, the
caller will be blocked on se_cmd->cmd_wait_stop completion
until the final kref_put() -> target_release_cmd_kref()
has been invoked to call complete().
However, when ABORT_TASK is completed with FUNCTION_COMPLETE
in core_tmr_abort_task(), the aborted se_cmd will have already
been removed from se_sess->sess_cmd_list via list_del_init().
This results in target_release_cmd_kref() hitting the
legacy list_empty() == true check, invoking ->release_cmd()
but skipping complete() to wakeup se_cmd->cmd_wait_stop
blocked earlier in transport_generic_free_cmd() code.
To address this bug, it's safe to go ahead and drop the
original list_empty() check so that fabric_stop invokes
the complete() as expected, since list_del_init() can
safely be used on a empty list.
Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command with a Simple task attribute is failed due to a Unit
Attention, then a subsequent command with an Ordered task attribute
will hang forever. The reason for this is that the Unit Attention
status is checked for in target_setup_cmd_from_cdb, before the call
to target_execute_cmd, which calls target_handle_task_attr, which
in turn increments dev->simple_cmds.
However, transport_generic_request_failure still calls
transport_complete_task_attr, which will decrement dev->simple_cmds.
In this case, simple_cmds is now -1. So when a command with the
Ordered task attribute is sent, target_handle_task_attr sees that
dev->simple_cmds is not 0, so it decides it can't execute the
command until all the (nonexistent) Simple commands have completed.
Reported-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Tested-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the volume resize operation shrinks a volume,
LEBs will be unmapped. Since unmapping will not erase these
LEBs immediately we have to wait for that operation to finish.
Otherwise in case of a power cut right after writing the new
volume table the UBI attach process can find more LEBs than the
volume table knows. This will render the UBI image unattachable.
Fix this issue by waiting for erase to complete and write the new
volume table afterward.
Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log