According to the IOMUXC_SW_PAD_CTL_PAD_UART2_RXD/TXD register define in
imx8mp RM, bit0 and bit3 are reserved, and the uart2 rx/tx pin should
enable the pull up, so need to set bit8 to 1. The original pinctl value
0x49 is incorrect and needs to be changed to 0x140, same as uart1 and
uart3.
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: d850f3e5d296 ("ARM: meson: Add SMP bringup code for Meson8 and Meson8b") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220512021611.47921-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This ASSERT in xfs_rename is a) incorrect, because
(RENAME_WHITEOUT|RENAME_NOREPLACE) is a valid combination, and
b) unnecessary, because actual invalid flag combinations are already
handled at the vfs level in do_renameat2() before we get called.
So, remove it.
Reported-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Fixes: 7dcf5c3e4527 ("xfs: add RENAME_WHITEOUT support") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Fixes: b4f20130af23 ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe") Fixes: f5d4abea3ce0 ("can: kvaser_usb: Add support for the USBcan-II family") Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.
This regression affects M32C based Leaf devices with non-16MHz clock.
Fixes: 854a2bede1f0 ("can: kvaser_usb: get CAN clock frequency from device") Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform device for the rng must be created much later in boot.
Otherwise it tries to connect to a parent that doesn't yet exist,
resulting in this splat:
This patch fixes the issue by doing the platform device creation inside
of machine_subsys_initcall.
Fixes: f3eac426657d ("powerpc/powernv: wire up rng during setup_arch") Cc: stable@vger.kernel.org Reported-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Sachin Sant <sachinp@linux.ibm.com>
[mpe: Change "of node" to "platform device" in change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220630121654.1939181-1-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the CONFIG_MEMREGION=n case, memregion_free() is meant to be a static
inline. 0day reports:
In file included from drivers/cxl/core/port.c:4:
include/linux/memregion.h:19:6: warning: no previous prototype for
function 'memregion_free' [-Wmissing-prototypes]
Mark memregion_free() static.
Fixes: 33dd70752cd7 ("lib: Uplevel the pmem "region" ida to a global allocator") Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Alison Schofield <alison.schofield@intel.com> Link: https://lore.kernel.org/r/165601455171.4042645.3350844271068713515.stgit@dwillia2-xfh Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of passing an extra bool argument to pm_runtime_release_supplier(),
make its callers take care of triggering a runtime-suspend of the
supplier device as needed.
We need to prevent that users configure a screen size which is smaller than the
currently selected font size. Otherwise rendering chars on the screen will
access memory outside the graphics memory region.
This patch adds a new function fbcon_modechange_possible() which
implements this check and which later may be extended with other checks
if necessary. The new function is called from the FBIOPUT_VSCREENINFO
ioctl handler in fbmem.c, which will return -EINVAL if userspace asked
for a too small screen size.
Prevent that users set a font size which is bigger than the physical screen.
It's unlikely this may happen (because screens are usually much larger than the
fonts and each font char is limited to 32x32 pixels), but it may happen on
smaller screens/LCD displays.
Verify that the fbdev or drm driver correctly adjusted the virtual
screen sizes. On failure report the failing driver and reject the screen
size change.
Notifier calling chain uses priority to determine the execution
order of the notifiers or listeners registered to the chain.
PCI bus device hot add utilizes the notification mechanism.
The current code sets low priority (INT_MIN) to Intel
dmar_pci_bus_notifier and postpones DMAR decoding after adding
new device into IOMMU. The result is that struct device pointer
cannot be found in DRHD search for the new device's DMAR/IOMMU.
Subsequently, the device is put under the "catch-all" IOMMU
instead of the correct one. This could cause system hang when
device TLB invalidation is sent to the wrong IOMMU. Invalidation
timeout error and hard lockup have been observed and data
inconsistency/crush may occur as well.
This patch fixes the issue by setting a positive priority(1) for
dmar_pci_bus_notifier while the priority of IOMMU bus notifier
uses the default value(0), therefore DMAR decoding will be in
advance of DRHD search for a new device to find the correct IOMMU.
Following is a 2-step example that triggers the bug by simulating
PCI device hot add behavior in Intel Sapphire Rapids server.
Add nft_set_pipapo_match_destroy() helper function to release the
elements in the lookup tables.
Stefano Brivio says: "We additionally look for elements pointers in the
cloned matching data if priv->dirty is set, because that means that
cloned data might point to additional elements we did not commit to the
working copy yet (such as the abort path case, but perhaps not limited
to it)."
Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges") Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are UAF bugs caused by rose_t0timer_expiry(). The
root cause is that del_timer() could not stop the timer
handler that is running and there is no synchronization.
One of the race conditions is shown below:
The rose_neigh is deallocated in position [1] and use in
position [2].
The crash trace triggered by POC is like below:
BUG: KASAN: use-after-free in expire_timers+0x144/0x320
Write of size 8 at addr ffff888009b19658 by task swapper/0/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0xbf/0xee
print_address_description+0x7b/0x440
print_report+0x101/0x230
? expire_timers+0x144/0x320
kasan_report+0xed/0x120
? expire_timers+0x144/0x320
expire_timers+0x144/0x320
__run_timers+0x3ff/0x4d0
run_timer_softirq+0x41/0x80
__do_softirq+0x233/0x544
...
This patch changes rose_stop_ftimer() and rose_stop_t0timer()
in rose_remove_neigh() to del_timer_sync() in order that the
timer handler could be finished before the resources such as
rose_neigh and so on are deallocated. As a result, the UAF
bugs could be mitigated.
Kuee reported a corner case where the tnum becomes constant after the call
to __reg_bound_offset(), but the register's bounds are not, that is, its
min bounds are still not equal to the register's max bounds.
This in turn allows to leak pointers through turning a pointer register as
is into an unknown scalar via adjust_ptr_min_max_vals().
What can be seen here is that R3=scalar(umin=32767,umax=32768,var_off=(0x7fff;
0x8000)) after the operation R3 += -32767 results in a 'malformed' constant, that
is, R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)). Intersecting with var_off has
not been done at that point via __update_reg_bounds(), which would have improved
the umax to be equal to umin.
Refactor the tnum <> min/max bounds information flow into a reg_bounds_sync()
helper and use it consistently everywhere. After the fix, bounds have been
corrected to R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) and thus the register
is regarded as a 'proper' constant scalar of 0.
Kuee reported a quirk in the jmp32's jeq/jne simulation, namely that the
register value does not match expectations for the fall-through path. For
example:
As can be seen on line 5 for the branch fall-through path in R2 [*] is that
given condition w2 != 0x8 is false, verifier should conclude that r2 = 8 as
upper 32 bit are known to be zero. However, verifier incorrectly concludes
that r2 = 571 which is far off.
The problem is it only marks false{true}_reg as known in the switch for JE/NE
case, but at the end of the function, it uses {false,true}_{64,32}off to
update {false,true}_reg->var_off and they still hold the prior value of
{false,true}_reg->var_off before it got marked as known. The subsequent
__reg_combine_32_into_64() then propagates this old var_off and derives new
bounds. The information between min/max bounds on {false,true}_reg from
setting the register to known const combined with the {false,true}_reg->var_off
based on the old information then derives wrong register data.
Fix it by detangling the BPF_JEQ/BPF_JNE cases and updating relevant
{false,true}_{64,32}off tnums along with the register marking to known
constant.
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad41b ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Cc: stable@vger.kernel.org Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit d5f9023fa61e ("can: bcm: delay release of struct bcm_op
after synchronize_rcu()") Thadeu Lima de Souza Cascardo introduced two
synchronize_rcu() calls in bcm_release() (only once at socket close)
and in bcm_delete_rx_op() (called on removal of each single bcm_op).
Unfortunately this slow removal of the bcm_op's affects user space
applications like cansniffer where the modification of a filter
removes 2048 bcm_op's which blocks the cansniffer application for
40(!) seconds.
In commit 181d4447905d ("can: gw: use call_rcu() instead of costly
synchronize_rcu()") Eric Dumazet replaced the synchronize_rcu() calls
with several call_rcu()'s to safely remove the data structures after
the removal of CAN ID subscriptions with can_rx_unregister() calls.
This patch adopts Erics approach for the can-bcm which should be
applicable since the removal of tasklet_kill() in bcm_remove_op() and
the introduction of the HRTIMER_MODE_SOFT timer handling in Linux 5.4.
Fixes: d5f9023fa61e ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") # >= 5.4 Link: https://lore.kernel.org/all/20220520183239.19111-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org Cc: Eric Dumazet <edumazet@google.com> Cc: Norbert Slusarek <nslusarek@gmx.net> Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fastpath in slab_alloc_node() assumes that c->slab is stable as long as
the TID stays the same. However, two places in __slab_alloc() currently
don't update the TID when deactivating the CPU slab.
If multiple operations race the right way, this could lead to an object
getting lost; or, in an even more unlikely situation, it could even lead to
an object being freed onto the wrong slab's freelist, messing up the
`inuse` counter and eventually causing a page to be freed to the page
allocator while it still contains slab objects.
(I haven't actually tested these cases though, this is just based on
looking at the code. Writing testcases for this stuff seems like it'd be
a pain...)
The race leading to state inconsistency is (all operations on the same CPU
and kmem_cache):
- task A: begin do_slab_free():
- read TID
- read pcpu freelist (==NULL)
- check `slab == c->slab` (true)
- [PREEMPT A->B]
- task B: begin slab_alloc_node():
- fastpath fails (`c->freelist` is NULL)
- enter __slab_alloc()
- slub_get_cpu_ptr() (disables preemption)
- enter ___slab_alloc()
- take local_lock_irqsave()
- read c->freelist as NULL
- get_freelist() returns NULL
- write `c->slab = NULL`
- drop local_unlock_irqrestore()
- goto new_slab
- slub_percpu_partial() is NULL
- get_partial() returns NULL
- slub_put_cpu_ptr() (enables preemption)
- [PREEMPT B->A]
- task A: finish do_slab_free():
- this_cpu_cmpxchg_double() succeeds()
- [CORRUPT STATE: c->slab==NULL, c->freelist!=NULL]
From there, the object on c->freelist will get lost if task B is allowed to
continue from here: It will proceed to the retry_load_slab label,
set c->slab, then jump to load_freelist, which clobbers c->freelist.
But if we instead continue as follows, we get worse corruption:
- task A: run __slab_free() on object from other struct slab:
- CPU_PARTIAL_FREE case (slab was on no list, is now on pcpu partial)
- task A: run slab_alloc_node() with NUMA node constraint:
- fastpath fails (c->slab is NULL)
- call __slab_alloc()
- slub_get_cpu_ptr() (disables preemption)
- enter ___slab_alloc()
- c->slab is NULL: goto new_slab
- slub_percpu_partial() is non-NULL
- set c->slab to slub_percpu_partial(c)
- [CORRUPT STATE: c->slab points to slab-1, c->freelist has objects
from slab-2]
- goto redo
- node_match() fails
- goto deactivate_slab
- existing c->freelist is passed into deactivate_slab()
- inuse count of slab-1 is decremented to account for object from
slab-2
At this point, the inuse count of slab-1 is 1 lower than it should be.
This means that if we free all allocated objects in slab-1 except for one,
SLUB will think that slab-1 is completely unused, and may free its page,
leading to use-after-free.
Fixes: c17dda40a6a4e ("slub: Separate out kmem_cache_cpu processing from deactivate_slab") Fixes: 03e404af26dc2 ("slub: fast release on full slab") Cc: stable@vger.kernel.org Signed-off-by: Jann Horn <jannh@google.com> Acked-by: Christoph Lameter <cl@linux.com> Acked-by: David Rientjes <rientjes@google.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Link: https://lore.kernel.org/r/20220608182205.2945720-1-jannh@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 30 Jun 2022 09:55:42 +0000 (11:55 +0200)]
clocksource/drivers/ixp4xx: remove EXPORT_SYMBOL_GPL from ixp4xx_timer_setup()
ixp4xx_timer_setup is exported, and so can not be an __init function.
But it does not need to be exported as it is only called from one
in-kernel function, so just remove the EXPORT_SYMBOL_GPL() marking to
resolve the build warning.
This is fixed "properly" in commit 41929c9f628b
("clocksource/drivers/ixp4xx: Drop boardfile probe path") but that can
not be backported to older kernels as the reworking of the IXP4xx
codebase is not suitable for stable releases.
This patch adds support for Telit LN920 0x1060 composition
0x1060: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: Carlo Lobrano <c.lobrano@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Fabio Porcedda <fabio.porcedda@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the PV driver life cycle the mappings are added to
the RB-tree by set_foreign_p2m_mapping(), which is called from
gnttab_map_refs() and are removed by clear_foreign_p2m_mapping()
which is called from gnttab_unmap_refs(). As both functions end
up calling __set_phys_to_machine_multi() which updates the RB-tree,
this function can be called concurrently.
There is already a "p2m_lock" to protect against concurrent accesses,
but the problem is that the first read of "phys_to_mach.rb_node"
in __set_phys_to_machine_multi() is not covered by it, so this might
lead to the incorrect mappings update (removing in our case) in RB-tree.
In my environment the related issue happens rarely and only when
PV net backend is running, the xen_add_phys_to_mach_entry() claims
that it cannot add new pfn <-> mfn mapping to the tree since it is
already exists which results in a failure when mapping foreign pages.
But there might be other bad consequences related to the non-protected
root reads such use-after-free, etc.
While at it, also fix the similar usage in __pfn_to_mfn(), so
initialize "struct rb_node *n" with the "p2m_lock" held in both
functions to avoid possible bad consequences.
The commit referenced below moved the invocation past the "next" label,
without any explanation. In fact this allows misbehaving backends undue
control over the domain the frontend runs in, as earlier detected errors
require the skb to not be freed (it may be retained for later processing
via xennet_move_rx_slot(), or it may simply be unsafe to have it freed).
This is CVE-2022-33743 / XSA-405.
Fixes: 6c5aa6fc4def ("xen networking: add basic XDP support for xen-netfront") Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the current bounce buffering logic used with persistent grants
into it's own option, and allow enabling it independently of
persistent grants. This allows to reuse the same code paths to
perform the bounce buffering required to avoid leaking contiguous data
in shared pages not part of the request fragments.
Reporting whether the backend is to be trusted can be done using a
module parameter, or from the xenstore frontend path as set by the
toolstack when adding the device.
Bounce all data on the skbs to be transmitted into zeroed pages if the
backend is untrusted. This avoids leaking data present in the pages
shared with the backend but not part of the skb fragments. This
requires introducing a new helper in order to allocate skbs with a
size multiple of XEN_PAGE_SIZE so we don't leak contiguous data on the
granted pages.
Reporting whether the backend is to be trusted can be done using a
module parameter, or from the xenstore frontend path as set by the
toolstack when adding the device.
Rather than use rseq_get_abi() and pass its result through a register to
the inline assembler, directly access the per-thread rseq area through a
memory reference combining the %gs segment selector, the constant offset
of the field in struct rseq, and the rseq_offset value (in a register).
Rather than use rseq_get_abi() and pass its result through a register to
the inline assembler, directly access the per-thread rseq area through a
memory reference combining the %fs segment selector, the constant offset
of the field in struct rseq, and the rseq_offset value (in a register).
gcc and clang each have their own compiler bugs with respect to asm
goto. Implement a work-around for compiler versions known to have those
bugs.
gcc prior to 4.8.2 miscompiles asm goto.
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
gcc prior to 8.1.0 miscompiles asm goto at O1.
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=103908
clang prior to version 13.0.1 miscompiles asm goto at O2.
https://github.com/llvm/llvm-project/issues/52735
Work around these issues by adding a volatile inline asm with
memory clobber in the fallthrough after the asm goto and at each
label target. Emit this for all compilers in case other similar
issues are found in the future.
The arm and mips work-around for asm goto size guess issues are not
properly documented, and lack reference to specific compiler versions,
upstream compiler bug tracker entry, and reproducer.
I can only find a loosely documented patch in my original LKML rseq post
refering to gcc < 7 on ARM, but it does not appear to be sufficient to
track the exact issue. Also, I am not sure MIPS really has the same
limitation.
Therefore, remove the work-around until we can properly document this.
The semantic of off_t is for file offsets. We mean to use it as an
offset from a pointer. We really expect it to fit in a single register,
and not use a 64-bit type on 32-bit architectures.
Fix runtime issues on ppc32 where the offset is always 0 due to
inconsistency between the argument type (off_t -> 64-bit) and type
expected by the inline assembler (32-bit).
Building the rseq basic test with
gcc version 5.4.0 20160609 (Ubuntu 5.4.0-6ubuntu1~16.04.12)
Target: powerpc-linux-gnu
leads to these errors:
/tmp/ccieEWxU.s: Assembler messages:
/tmp/ccieEWxU.s:118: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:118: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:121: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:121: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:626: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:626: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:629: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:629: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:735: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:735: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:738: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:738: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:741: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:741: Error: junk at end of line: `,8'
Makefile:581: recipe for target 'basic_percpu_ops_test.o' failed
Based on discussion with Linux powerpc maintainers and review of
the use of the "m" operand in powerpc kernel code, add the missing
%Un%Xn (where n is operand number) to the lwz, stw, ld, and std
instructions when used with "m" operands.
Using "WORD" to mean either a 32-bit or 64-bit type depending on
the architecture is misleading. The term "WORD" really means a
32-bit type in both 32-bit and 64-bit powerpc assembler. The intent
here is to wrap load/store to intptr_t into common macros for both
32-bit and 64-bit.
Rename the macros with a RSEQ_ prefix, and use the terms "INT"
for always 32-bit type, and "LONG" for architecture bitness-sized
type.
glibc-2.35 (upcoming release date 2022-02-01) exposes the rseq per-thread
data in the TCB, accessible at an offset from the thread pointer, rather
than through an actual Thread-Local Storage (TLS) variable, as the
Linux kernel selftests initially expected.
The __rseq_abi TLS and glibc-2.35's ABI for per-thread data cannot
actively coexist in a process, because the kernel supports only a single
rseq registration per thread.
Here is the scheme introduced to ensure selftests can work both with an
older glibc and with glibc-2.35+:
- librseq exposes its own "rseq_offset, rseq_size, rseq_flags" ABI.
- librseq queries for glibc rseq ABI (__rseq_offset, __rseq_size,
__rseq_flags) using dlsym() in a librseq library constructor. If those
are found, copy their values into rseq_offset, rseq_size, and
rseq_flags.
- Else, if those glibc symbols are not found, handle rseq registration
from librseq and use its own IE-model TLS to implement the rseq ABI
per-thread storage.
This is done in preparation for the selftest uplift to become compatible
with glibc-2.35.
glibc-2.35 exposes the rseq per-thread data in the TCB, accessible
at an offset from the thread pointer.
The toolchains do not implement accessing the thread pointer on all
architectures. Provide thread pointer getters for ppc and x86 which
lack (or lacked until recently) toolchain support.
This is done in preparation for the selftest uplift to become compatible
with glibc-2.35.
glibc-2.35 exposes the rseq per-thread data in the TCB, accessible
at an offset from the thread pointer, rather than through an actual
Thread-Local Storage (TLS) variable, as the kernel selftests initially
expected.
Introduce a rseq_get_abi() helper, initially using the __rseq_abi
TLS variable, in preparation for changing this userspace ABI for one
which is compatible with glibc-2.35.
Note that the __rseq_abi TLS and glibc-2.35's ABI for per-thread data
cannot actively coexist in a process, because the kernel supports only
a single rseq registration per thread.
This is done in preparation for the selftest uplift to become compatible
with glibc-2.35.
All accesses to the __rseq_abi fields are volatile, but remove the
volatile from the TLS variable declaration, otherwise we are stuck with
volatile for the upcoming rseq_get_abi() helper.
The Linux kernel rseq uapi header has a broken layout for the
rseq_cs.ptr field on 32-bit little endian architectures. The entire
rseq_cs.ptr field is planned for removal, leaving only the 64-bit
rseq_cs.ptr64 field available.
Both glibc and librseq use their own copy of the Linux kernel uapi
header, where they introduce proper union fields to access to the 32-bit
low order bits of the rseq_cs pointer on 32-bit architectures.
Introduce a copy of the Linux kernel uapi headers in the Linux kernel
selftests.
ARRAY_SIZE is defined in several selftests. Remove definitions from
individual test files and include header file for the define instead.
ARRAY_SIZE define is added in a separate patch to prepare for this
change.
Remove ARRAY_SIZE from rseq tests and pickup the one defined in
kselftest.h.
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes: 8808a793f052 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
CC: Denis Efremov <efremov@linux.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: kernel test robot <lkp@intel.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In qoriq_cpufreq_probe(), of_find_matching_node() will return a
node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Fixes: 157f527639da ("cpufreq: qoriq: convert to a platform driver")
[ Viresh: Fixed Author's name in commit log ] Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
unmap_grant_pages() currently waits for the pages to no longer be used.
In https://github.com/QubesOS/qubes-issues/issues/7481, this lead to a
deadlock against i915: i915 was waiting for gntdev's MMU notifier to
finish, while gntdev was waiting for i915 to free its pages. I also
believe this is responsible for various deadlocks I have experienced in
the past.
Avoid these problems by making unmap_grant_pages async. This requires
making it return void, as any errors will not be available when the
function returns. Fortunately, the only use of the return value is a
WARN_ON(), which can be replaced by a WARN_ON when the error is
detected. Additionally, a failed call will not prevent further calls
from being made, but this is harmless.
Because unmap_grant_pages is now async, the grant handle will be sent to
INVALID_GRANT_HANDLE too late to prevent multiple unmaps of the same
handle. Instead, a separate bool array is allocated for this purpose.
This wastes memory, but stuffing this information in padding bytes is
too fragile. Furthermore, it is necessary to grab a reference to the
map before making the asynchronous call, and release the reference when
the call returns.
It is also necessary to guard against reentrancy in gntdev_map_put(),
and to handle the case where userspace tries to map a mapping whose
contents have not all been freed yet.
Fixes: 745282256c75 ("xen/gntdev: safely unmap grants in case they are still in use") Cc: stable@vger.kernel.org Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220622022726.2538-1-demi@invisiblethingslab.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the third packet of 3WHS connection establishment
contains payload, it is added into socket receive queue
without the XFRM check and the drop of connection tracking
context.
This means that if the data is left unread in the socket
receive queue, conntrack module can not be unloaded.
As most applications usually reads the incoming data
immediately after accept(), bug has been hiding for
quite a long time.
Commit 68822bdf76f1 ("net: generalize skb freeing
deferral to per-cpu lists") exposed this bug because
even if the application reads this data, the skb
with nfct state could stay in a per-cpu cache for
an arbitrary time, if said cpu no longer process RX softirqs.
Many thanks to Ilya Maximets for reporting this issue,
and for testing various patches:
https://lore.kernel.org/netdev/20220619003919.394622-1-i.maximets@ovn.org/
Note that I also added a missing xfrm4_policy_check() call,
although this is probably not a big issue, as the SYN
packet should have been dropped earlier.
The final parameter of filemap_write_and_wait_range is the end of the
range to flush, not the length of the range to flush.
Fixes: 46afb0628b86 ("xfs: only flush the unshared range in xfs_reflink_unshare") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the mount superblock counters up to date for !lazysbcount
filesystems so that when we log the superblock they do not need
updating in any way because they are already correct.
It's found by what Zorro reported:
1. mkfs.xfs -f -l lazy-count=0 -m crc=0 $dev
2. mount $dev $mnt
3. fsstress -d $mnt -p 100 -n 1000 (maybe need more or less io load)
4. umount $mnt
5. xfs_repair -n $dev
and I've seen no problem with this patch.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reported-by: Zorro Lang <zlang@redhat.com> Reviewed-by: Gao Xiang <hsiangkao@redhat.com> Signed-off-by: Gao Xiang <hsiangkao@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removal of kmem_zone_init wrappers accidentally changed a slab cache
name from "xfs_trans" to "xf_trans". Fix this so that userspace
consumers of /proc/slabinfo and /sys/kernel/slab can find it again.
Fixes: b1231760e443 ("xfs: Remove slab init wrappers") Signed-off-by: Anthony Iliopoulos <ailiop@suse.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the BUILD_BUG_ON to xfs_errortag_add() in order to make sure that
the length of xfs_errortag_random_default matches XFS_ERRTAG_MAX when
building.
Signed-off-by: Gao Xiang <hsiangkao@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Skip the warnings about mount option being deprecated if we are
remounting and deprecated option state is not changing.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211605 Fix-suggested-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Pavel Reichl <preichl@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename mp variable to parsisng_mp so it is easy to distinguish
between current mount point handle and handle for mount point
which mount options are being parsed.
Suggested-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Pavel Reichl <preichl@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the iomap code using PF_MEMALLOC_NOFS to detect transaction
recursion in XFS is just wrong. Remove it from the iomap code and
replace it with XFS specific internal checks using
current->journal_info instead.
[djwong: This change also realigns the lifetime of NOFS flag changes to
match the incore transaction, instead of the inconsistent scheme we have
now.]
Fixes: 9070733b4efa ("xfs: abstract PF_FSTRANS to PF_MEMALLOC_NOFS") Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric reports that syzbot made short work out of my speculative
fix. Indeed when queue gets detached its tfile->tun remains,
so we would try to stop NAPI twice with a detach(), close()
sequence.
Alternative fix would be to move tun_napi_disable() to
tun_detach_all() and let the NAPI run after the queue
has been detached.
Fixes: a8fc8cb5692a ("net: tun: stop NAPI when detaching queues") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220629181911.372047-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently added debug in commit f9aefd6b2aa3 ("net: warn if mac header
was not set") caught a bug in skb_tunnel_check_pmtu(), as shown
in this syzbot report [1].
In ndo_start_xmit() paths, there is really no need to use skb->mac_header,
because skb->data is supposed to point at it.
Fixes: 4cb47a8644cc ("tunnels: PMTU discovery support for directly bridged IP packets") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All other opcodes correctly check if this is set and -EINVAL if it is
and they don't support that field, for some reason the these were
forgotten.
This was unified a bit differently in the upstream tree, but had the
same effect as making sure we error on this field. Rather than have
a painful backport of the upstream commit, just fixup the mentioned
opcodes.
epic_close() calls epic_rx() and uses dma buffer, but in epic_remove_one()
we already freed the dma buffer. To fix this issue, reorder function calls
like in the .probe function.
It was caused by the 'l' passed into tipc_bcast_rcv() is NULL. When it
creates a node in tipc_node_check_dest(), after inserting the new node
into hashtable in tipc_node_create(), it creates the bc link. However,
there is a gap between this insert and bc link creation, a bc packet
may come in and get the node from the hashtable then try to dereference
its bc link, which is NULL.
This patch is to fix it by moving the bc link creation before inserting
into the hashtable.
Note that for a preliminary node becoming "real", the bc link creation
should also be called before it's rehashed, as we don't create it for
preliminary nodes.
Fixes: 4cbf8ac2fe5a ("tipc: enable creating a "preliminary" node") Reported-by: Shuang Li <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are packets which doesn't have a payload. In that case, the second
i2c_master_read() will have a zero length. But because the NFC
controller doesn't have any data left, it will NACK the I2C read and
-ENXIO will be returned. In case there is no payload, just skip the
second i2c master read.
Fixes: 6be88670fc59 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0622cab0341c ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit 0622cab0341c ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
If during an action flush operation one of the actions is still being
referenced, the flush operation is aborted and the kernel returns to
user space with an error. However, if the kernel was able to flush, for
example, 3 actions and failed on the fourth, the kernel will not notify
user space that it deleted 3 actions before failing.
This patch fixes that behaviour by notifying user space of how many
actions were deleted before flush failed and by setting extack with a
message describing what happened.
Fixes: 55334a5db5cd ("net_sched: act: refuse to remove bound action outside") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Element already exists in the hashtable.
- Another packet won race to insert an entry in the hashtable.
In both cases, new() has already bumped the counter via atomic_add_unless(),
therefore, decrement the set element counter.
Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
This function only calls of_node_put() in normal path,
missing it in error paths.
Add missing of_node_put() to avoid refcount leak.
We currently depend on probe() calling virtio_device_ready() -
which happens after netdev
registration. Since ndo_open() can be called immediately
after register_netdev, this means there exists a race between
ndo_open() and virtio_device_ready(): the driver may start to use the
device (e.g. TX) before DRIVER_OK which violates the spec.
Fix this by switching to use register_netdevice() and protect the
virtio_device_ready() with rtnl_lock() to make sure ndo_open() can
only be called after virtio_device_ready().
Fixes: 0d2e1a2926b18 ("caif_virtio: Introduce caif over virtio") Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220620051115.3142-3-jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit 5801f064e351 ("net: ipv6: unexport __init-annotated seg6_hmac_init()"),
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
This remove the EXPORT_SYMBOL to fix modpost warning:
WARNING: modpost: vmlinux.o(___ksymtab+seg6_hmac_net_init+0x0): Section mismatch in reference from the variable __ksymtab_seg6_hmac_net_init to the function .init.text:seg6_hmac_net_init()
The symbol seg6_hmac_net_init is exported and annotated __init
Fix this by removing the __init annotation of seg6_hmac_net_init or drop the export.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20220628033134.21088-1-yuehaibing@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbnet provides some helper functions that are also used in
the context of reset() operations. During a reset the other
drivers on a device are unable to operate. As that can be block
drivers, a driver for another interface cannot use paging
in its memory allocations without risking a deadlock.
Use GFP_NOIO in the helpers.
Make sure to save the passed QP timeout attribute when the QP gets modified,
so when calling query QP the right value is reported and not the
converted value that is required by the firmware. This issue was found
while running the pyverbs tests.
Fixes: cecbcddf6461 ("qedr: Add support for QP verbs") Link: https://lore.kernel.org/r/20220525132029.84813-1-kamalheib1@gmail.com Signed-off-by: Kamal Heib <kamalheib1@gmail.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some RX errors, notably when disconnecting the cable, increase the RCSR
register. Once half full (0x7fff), an interrupt flood is generated. I
measured ~3k/s interrupts even after the RX errors transfer was
stopped.
Since we don't read and clear the RCSR register, we should disable this
interrupt.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission") Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unplugging an Ethernet cable, false carrier events were produced by
the PHY at a very high rate. Once the false carrier counter full, an
interrupt was triggered every few clock cycles until the cable was
replugged. This resulted in approximately 10k/s interrupts.
Since the false carrier counter (FCSCR) is never used, we can safely
disable this interrupt.
In addition to improving performance, this also solved MDIO read
timeouts I was randomly encountering with an i.MX8 fec MAC because of
the interrupt flood. The interrupt count and MDIO timeout fix were
tested on a v5.4.110 kernel.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission") Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While looking at a syzbot report I noticed the NAPI only gets
disabled before it's deleted. I think that user can detach
the queue before destroying the device and the NAPI will never
be stopped.
Fixes: 943170998b20 ("tun: enable NAPI for TUN/TAP driver") Acked-by: Petar Penkov <ppenkov@aviatrix.com> Link: https://lore.kernel.org/r/20220623042105.2274812-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot found a race between tun file and device destruction.
NAPIs live in struct tun_file which can get destroyed before
the netdev so we have to del them explicitly. The current
code is missing deleting the NAPI if the queue was detached
first.
Fixes: 943170998b20 ("tun: enable NAPI for TUN/TAP driver") Reported-by: syzbot+b75c138e9286ac742647@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20220623042039.2274708-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.
We currently call virtio_device_ready() after netdev
registration. Since ndo_open() can be called immediately
after register_netdev, this means there exists a race between
ndo_open() and virtio_device_ready(): the driver may start to use the
device before DRIVER_OK which violates the spec.
Fix this by switching to use register_netdevice() and protect the
virtio_device_ready() with rtnl_lock() to make sure ndo_open() can
only be called after virtio_device_ready().
Fixes: 4baf1e33d0842 ("virtio_net: enable VQs early") Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220617072949.30734-1-jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 57bc3d3ae8c1 ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup") Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Signed-off-by: Jose Alonso <joalonsof@gmail.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are UAF bugs in rose_heartbeat_expiry(), rose_timer_expiry()
and rose_idletimer_expiry(). The root cause is that del_timer()
could not stop the timer handler that is running and the refcount
of sock is not managed properly.
This patch adds refcount of sock when we use functions
such as rose_start_heartbeat() and so on to start timer,
and decreases the refcount of sock when timer is finished
or deleted by functions such as rose_stop_heartbeat()
and so on. As a result, the UAF bugs could be mitigated.
Looks like there are still cases when "space_left - frag1bytes" can
legitimately exceed PAGE_SIZE. Ensure that xdr->end always remains
within the current encode buffer.
Reported-by: Bruce Fields <bfields@fieldses.org> Reported-by: Zorro Lang <zlang@redhat.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216151 Fixes: 6c254bf3b637 ("SUNRPC: Fix the calculation of xdr->end in xdr_get_next_encode_buffer()") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log