Commit f5775e0b6116 ("x86/xen: discard RAM regions above the maximum
reservation") left host memory not assigned to dom0 as available for
memory hotplug.
Unfortunately this also meant that those regions could be used by
others. Specifically, commit fa564ad96366 ("x86/PCI: Enable a 64bit BAR
on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)") may try to map those
addresses as MMIO.
To prevent this mark unallocated host memory as E820_TYPE_UNUSABLE (thus
effectively reverting f5775e0b6116) and keep track of that region as
a hostmem resource that can be used for the hotplug.
During unload, on mlx5_stop_eqs we move command interface from events
mode to polling mode, but if command interface EQ destroy fail we move
back to events mode.
That's wrong since even if we fail to destroy command interface EQ, we
do release its irq, so no interrupts will be received.
When mlx5_stop_eqs fails to destroy any of the eqs it returns with an error.
In such failure flow the function will return without
releasing all EQs irqs and then pci_free_irq_vectors will fail.
Fix by only warn on destroy EQ failure and continue to release other
EQs and their irqs.
It fixes the following kernel trace:
kernel: kernel BUG at drivers/pci/msi.c:352!
...
...
kernel: Call Trace:
kernel: pci_disable_msix+0xd3/0x100
kernel: pci_free_irq_vectors+0xe/0x20
kernel: mlx5_load_one.isra.17+0x9f5/0xec0 [mlx5_core]
As noted in dwmac4_wrback_get_rx_timestamp_status the timestamp is found
in the context descriptor following the current descriptor. However the
current code looks for the context descriptor in the current
descriptor, which will always fail.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same fix as the patch "ip_gre: remove the incorrect mtu limit for
ipgre tap" is also needed for ip6_gre.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipgre tap driver calls ether_setup(), after commit 61e84623ace3
("net: centralize net_device min/max MTU checking"), the range
of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
It causes the dev mtu of the ipgre tap device to not be greater
than 1500, this limit value is not correct for ipgre tap device.
Besides, it's .change_mtu already does the right check. So this
patch is just to set max_mtu as 0, and leave the check to it's
.change_mtu.
Fixes: 61e84623ace3 ("net: centralize net_device min/max MTU checking") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike ip tunnels, now vxlan doesn't do any pmtu update for
upper dst pmtu, even if it doesn't match the lower dst pmtu
any more.
The problem can be reproduced when reducing the vxlan lower
dev's pmtu when running netperf. In jianlin's testing, the
performance went to 1/7 of the previous.
This patch is to update the upper dst pmtu to match the lower
dst pmtu on tx path so that packets can be sent out even when
lower dev's pmtu has been changed.
It also works for metadata dst.
Note that this patch doesn't process any pmtu icmp packet.
But even in the future, the support for pmtu icmp packets
process of udp tunnels will also needs this.
The same thing will be done for geneve in another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few thousand such pages are usually left around due to the re-use of
L1 tables having been provided by the hypervisor (Dom0) or tool stack
(DomU). Set NX in the direct map variant, which needs to be done in L2
due to the dual use of the re-used L1s.
For x86_configure_nx() to actually do what it is supposed to do, call
get_cpu_cap() first. This was broken by commit 4763ed4d45 ("x86, mm:
Clean up and simplify NX enablement") when switching away from the
direct EFER read.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In trying to add support for drm_hwcomposer to HiKey,
I've needed to utilize the ION CMA heap, and I've noticed
problems with allocations on newer kernels failing.
It seems back with 204f672255c2 ("ion: Use CMA APIs directly"),
the ion_cma_heap code was modified to use the CMA API, but
kept the arguments as buffer lengths rather then number of pages.
This results in errors as we don't have enough pages in CMA to
satisfy the exaggerated requests.
This patch converts the ion_cma_heap CMA API usage to properly
request pages.
It also fixes a minor issue in the allocation where in the error
path, the cma_release is called with the buffer->size value which
hasn't yet been set.
Cc: Laura Abbott <labbott@redhat.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Archit Taneja <architt@codeaurora.org> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Dmitry Shmidt <dimitrysh@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Amit Pundir <amit.pundir@linaro.org> Fixes: 204f672255c2 ("staging: android: ion: Use CMA APIs directly") Acked-by: Laura Abbott <labbott@redhat.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cgroup_migrate_add_task() it checks for PF_EXITING flag of task T.
Task T will not migrate to destination cgroup. css_task_iter_start()
will keep pointing to task T in loop waiting for task T cg_list node
to be removed.
Task T
do_exit()
exit_signals() // sets PF_EXITING
exit_task_namespaces()
switch_task_namespaces()
free_nsproxy()
put_mnt_ns()
drop_collected_mounts()
namespace_unlock()
synchronize_rcu()
_synchronize_rcu_expedited()
schedule_work() // on cpu0 low priority worker pool
wait_event() // waiting for work item to execute
Task T inserted a work item in the worklist of cpu0 low priority
worker pool. It is waiting for expedited grace period work item
to execute. This work item will only be executed once kworker/0:0
complete execution of cpuset_hotplug_workfn().
kworker/0:0 ==> Task T ==>kworker/0:0
In case of PF_EXITING task being migrated from source to destination
cgroup, migrate next available task in source cgroup.
In skylake platform, we hear a loud pop noise(0 dB) at start of
audio capture power up sequence. This patch removes the pop noise
from the recording by adding a delay before enabling ADC.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Radu Pirea <radu.pirea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit, it just reports an empty stack trace.
The new behavior is actually probably more correct. If the stack
refcount has gone down to zero, then the task has already gone through
do_exit() and isn't going to run anymore. The stack could be freed at
any time and is basically gone, so reporting an empty stack makes sense.
However, save_stack_trace_tsk_reliable() treats such a missing stack
condition as an error. That can cause livepatch transition stalls if
there are any unreaped zombies. Instead, just treat it as a reliable,
empty stack.
Reported-and-tested-by: Miroslav Benes <mbenes@suse.cz> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: live-patching@vger.kernel.org Fixes: af085d9084b4 ("stacktrace/x86: add function for detecting reliable stack traces") Link: http://lkml.kernel.org/r/e4b09e630e99d0c1080528f0821fc9d9dbaeea82.1513631620.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By crafting special packets, it is possible to cause recursion
in our kernel when processing transport-mode packets at levels
that are only limited by packet size.
The easiest one is with DNAT, but an even worse one is where
UDP encapsulation is used in which case you just have to insert
an UDP encapsulation header in between each level of recursion.
This patch avoids this problem by reinjecting tranport-mode packets
through a tasklet.
On my GP107 when I load nouveau after unloading it, for some reason the
GPU stopped sending or the CPU stopped receiving interrupts if MSI was
enabled.
Doing a rearm once before getting any interrupts fixes this.
Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now when reneging events in sctp_ulpq_renege(), the variable freed
could be increased by a __u16 value twice while freed is of __u16
type. It means freed may overflow at the second addition.
This patch is to fix it by using __u32 type for 'freed', while at
it, also to remove 'if (chunk)' check, as all renege commands are
generated in sctp_eat_data and it can't be NULL.
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up to f5caf621ee35 ("x86/asm: Fix inline asm call constraints for Clang")
we were able to use x86 headers to build to the 'bpf' clang target, as
done by the BPF code in tools/perf/.
With that commit, we ended up with following failure for 'perf test LLVM', this
is because "clang ... -target bpf ..." fails since 4.0 does not have bpf inline
asm support and 6.0 does not recognize the register 'esp', fix it by guarding
that part with an #ifndef __BPF__, that is defined by clang when building to
the "bpf" target.
# perf test -v LLVM
37: LLVM search and compile :
37.1: Basic BPF llvm compile :
--- start ---
test child forked, pid 25526
Kernel build dir is set to /lib/modules/4.14.0+/build
set env: KBUILD_DIR=/lib/modules/4.14.0+/build
unset env: KBUILD_OPTS
include option is set to -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: NR_CPUS=4
set env: LINUX_VERSION_CODE=0x40e00
set env: CLANG_EXEC=/usr/local/bin/clang
set env: CLANG_OPTIONS=-xc
set env: KERNEL_INC_OPTIONS= -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: WORKING_DIR=/lib/modules/4.14.0+/build
set env: CLANG_SOURCE=-
llvm compiling command template: echo '/*
* bpf-script-example.c
* Test basic LLVM building
*/
#ifndef LINUX_VERSION_CODE
# error Need LINUX_VERSION_CODE
# error Example: for 4.2 kernel, put 'clang-opt="-DLINUX_VERSION_CODE=0x40200" into llvm section of ~/.perfconfig'
#endif
#define BPF_ANY 0
#define BPF_MAP_TYPE_ARRAY 2
#define BPF_FUNC_map_lookup_elem 1
#define BPF_FUNC_map_update_elem 2
SEC("func=SyS_epoll_wait")
int bpf_func__SyS_epoll_wait(void *ctx)
{
int ind =0;
int *flag = bpf_map_lookup_elem(&flip_table, &ind);
int new_flag;
if (!flag)
return 0;
/* flip flag and store back */
new_flag = !*flag;
bpf_map_update_elem(&flip_table, &ind, &new_flag, BPF_ANY);
return new_flag;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
' | $CLANG_EXEC -D__KERNEL__ -D__NR_CPUS__=$NR_CPUS -DLINUX_VERSION_CODE=$LINUX_VERSION_CODE $CLANG_OPTIONS $KERNEL_INC_OPTIONS -Wno-unused-value -Wno-pointer-sign -working-directory $WORKING_DIR -c "$CLANG_SOURCE" -target bpf -O2 -o -
test child finished with 0
---- end ----
LLVM search and compile subtest 0: Ok
37.2: kbuild searching :
--- start ---
test child forked, pid 25950
Kernel build dir is set to /lib/modules/4.14.0+/build
set env: KBUILD_DIR=/lib/modules/4.14.0+/build
unset env: KBUILD_OPTS
include option is set to -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: NR_CPUS=4
set env: LINUX_VERSION_CODE=0x40e00
set env: CLANG_EXEC=/usr/local/bin/clang
set env: CLANG_OPTIONS=-xc
set env: KERNEL_INC_OPTIONS= -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: WORKING_DIR=/lib/modules/4.14.0+/build
set env: CLANG_SOURCE=-
llvm compiling command template: echo '/*
* bpf-script-test-kbuild.c
* Test include from kernel header
*/
#ifndef LINUX_VERSION_CODE
# error Need LINUX_VERSION_CODE
# error Example: for 4.2 kernel, put 'clang-opt="-DLINUX_VERSION_CODE=0x40200" into llvm section of ~/.perfconfig'
#endif
#define SEC(NAME) __attribute__((section(NAME), used))
SEC("func=vfs_llseek")
int bpf_func__vfs_llseek(void *ctx)
{
return 0;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
' | $CLANG_EXEC -D__KERNEL__ -D__NR_CPUS__=$NR_CPUS -DLINUX_VERSION_CODE=$LINUX_VERSION_CODE $CLANG_OPTIONS $KERNEL_INC_OPTIONS -Wno-unused-value -Wno-pointer-sign -working-directory $WORKING_DIR -c "$CLANG_SOURCE" -target bpf -O2 -o -
In file included from <stdin>:12:
In file included from /home/acme/git/linux/arch/x86/include/uapi/asm/ptrace.h:5:
In file included from /home/acme/git/linux/include/linux/compiler.h:242:
In file included from /home/acme/git/linux/arch/x86/include/asm/barrier.h:5:
In file included from /home/acme/git/linux/arch/x86/include/asm/alternative.h:10:
/home/acme/git/linux/arch/x86/include/asm/asm.h:145:50: error: unknown register name 'esp' in asm
register unsigned long current_stack_pointer asm(_ASM_SP);
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:44:18: note: expanded from macro '_ASM_SP'
#define _ASM_SP __ASM_REG(sp)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:27:32: note: expanded from macro '__ASM_REG'
#define __ASM_REG(reg) __ASM_SEL_RAW(e##reg, r##reg)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:18:29: note: expanded from macro '__ASM_SEL_RAW'
# define __ASM_SEL_RAW(a,b) __ASM_FORM_RAW(a)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:11:32: note: expanded from macro '__ASM_FORM_RAW'
# define __ASM_FORM_RAW(x) #x
^
<scratch space>:4:1: note: expanded from here
"esp"
^
1 error generated.
ERROR: unable to compile -
Hint: Check error message shown above.
Hint: You can also pre-compile it into .o using:
clang -target bpf -O2 -c -
with proper -I and -D options.
Failed to compile test case: 'kbuild searching'
test child finished with -1
---- end ----
LLVM search and compile subtest 1: FAILED!
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David Ahern <dsahern@gmail.com> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wang Nan <wangnan0@huawei.com> Cc: Yonghong Song <yhs@fb.com> Link: https://lkml.kernel.org/r/20171128175948.GL3298@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An additional 'ip' will be pushed to the stack, for restoring the
DACR later, if CONFIG_CPU_SW_DOMAIN_PAN defined.
However, the fixup still get the err_ptr by add #8*4 to sp, which
results in the fact that the code area pointed by the LR will be
overwritten, or the kernel will crash if CONFIG_DEBUG_RODATA is enabled.
In testing, I found that the thread stack can be 16 kB when using an irq
stack. Without it, the thread stack needs to be 32 kB. Currently, the irq
stack is 32 kB. While it probably could be 16 kB, I would prefer to leave it
as is for safety.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One example of when an ICMPv6 packet is required to be looped back is
when a host acts as both a Multicast Listener and a Multicast Router.
A Multicast Router will listen on address ff02::16 for MLDv2 messages.
Currently, MLDv2 messages originating from a Multicast Listener running
on the same host as the Multicast Router are not being delivered to the
Multicast Router. This is due to dst.input being assigned the default
value of dst_discard.
This results in the packet being looped back but discarded before being
delivered to the Multicast Router.
This patch sets dst.input to ip6_input to ensure a looped back packet
is delivered to the Multicast Router.
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A negative return value of brcmstb_nand_verify_erased_page() indicates a
real bitflip error of an erased page, and other return values (>= 0) show
the corrected bitflip number. Zero return value means no bitflip, but the
current driver code treats it as an error, and eventually leads to
falsely reported ECC error.
Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflip") Signed-off-by: Albert Hsieh <wen.hsieh@broadcom.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When erased subpages are read then the BCH decoder returns STATUS_ERASED
if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips.
When there are bitflips, we have to set these bits again to show the
upper layers a completely erased page. When a bitflip happens in the
exact byte where the bad block marker is, then this byte is swapped
with another byte in block_mark_swapping(). The correction code then
detects a bitflip in another subpage and no longer corrects the bitflip
where it really happens.
Correct this behaviour by calling block_mark_swapping() after the
bitflips have been corrected.
In our case UBIFS failed with this bug because it expects erased
pages to be really empty:
UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735
UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed
UBIFS error (pid 187): do_commit: commit failed, error -117
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems with large MRRS on device (2K, 4K) with high data rates and/or
large MTU, atlantic observes DMA packet buffer overflow. On some systems
that causes PCIe transaction errors, hardware NMIs or datapath freeze.
This patch
1) Limits MRRS from device side to 2K (thats maximum our hardware supports)
2) Limit maximum size of outstanding TX DMA data read requests. This makes
hardware buffers running fine.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices with IDs matching the "stripe" quirk don't actually have
this quirk, and don't have an MDTS value. When MDTS is not set, the
driver sets the max sectors to UINT_MAX, which is not a power of 2,
hitting a BUG_ON from blk_queue_chunk_sectors. This patch skips setting
chunk sectors for such devices.
Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two put references in the failure case of initial
create_association. The first put actually frees the controller, thus the
second put references freed memory.
Remove the unnecessary 2nd put.
Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_get_irq_byname() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq_byname() error
checking for zero is not correct.
Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support") Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.
To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.
In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.
Found by Linux Driver Verification project (linuxtesting.org).
"FIB_CONTEXT_FLAG_TIMEDOUT" flag is set in aac_eh_abort to indicate
command timeout. Using the same flag in reset handler causes the command
to time out and the I/Os were dropped.
Define a new flag "FIB_CONTEXT_FLAG_EH_RESET" to make sure I/O is
properly handled in eh_reset handler.
[mkp: tweaked commit message]
Signed-off-by: Prasad B Munirathnam <prasad.munirathnam@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-8 warns about using strncpy() with the source size as the limit:
fs/exec.c:1223:32: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
This is indeed slightly suspicious, as it protects us from source
arguments without NUL-termination, but does not guarantee that the
destination is terminated.
This keeps the strncpy() to ensure we have properly padded target
buffer, but ensures that we use the correct length, by passing the
actual length of the destination buffer as well as adding a build-time
check to ensure it is exactly TASK_COMM_LEN.
There are only 23 callsites which I all reviewed to ensure this is
currently the case. We could get away with doing only the check or
passing the right length, but it doesn't hurt to do both.
The POSIX specification defines that relative CLOCK_REALTIME timers are not
affected by clock modifications. Those timers have to use CLOCK_MONOTONIC
to ensure POSIX compliance.
The introduction of the additional HRTIMER_MODE_PINNED mode broke this
requirement for pinned timers.
There is no user space visible impact because user space timers are not
using pinned mode, but for consistency reasons this needs to be fixed.
Check whether the mode has the HRTIMER_MODE_REL bit set instead of
comparing with HRTIMER_MODE_ABS.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keescook@chromium.org Fixes: 597d0275736d ("timers: Framework for identifying pinned timers") Link: http://lkml.kernel.org/r/20171221104205.7269-7-anna-maria@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Mike Galbraith <efault@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building an allmodconfig kernel fails horribly because of
endian mismatch. It turns out that the -mlittle-endian
switch was not honored at all as we were using the wrong
Kconfig symbol and failing to apply CPUFLAGS to the CFLAGS.
Finally, the linker flags did not get set right.
This addresses all three of those issues, which now lets
me build both big-endian and little-endian kernels for
testing.
Fixes: 428dbf156cc5 ("arch: change default endian for microblaze") Fixes: 206d3642d8ee ("arch/microblaze: add choice for endianness and update Makefile") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The m32r Kconfig provides both CPU_BIG_ENDIAN and CPU_LITTLE_ENDIAN
configuration options. As they are user-selectable and independent,
this allows invalid configurations:
- All m32r defconfigs build a big endian kernel, but CPU_BIG_ENDIAN is
not set, causing compiler warnings like:
- Since commit 5bdfca6435b82944 ("m32r: define CPU_BIG_ENDIAN"),
building an allmodconfig or allyesconfig enables both
CONFIG_CPU_BIG_ENDIAN and CONFIG_CPU_LITTLE_ENDIAN.
While this did get rid of the warning above, both options are
obviously mutually exclusive.
Fix this by making only CPU_LITTLE_ENDIAN configurable by the user, as
before, and by making sure exactly one of CPU_BIG_ENDIAN and
CPU_LITTLE_ENDIAN is always enabled.
When a request is preempted, it is unsubmitted from the HW queue and
removed from the active list of breadcrumbs. In the process, this
however triggers the signaler and it may see the clear rbtree with the
old, and still valid, seqno, or it may match the cleared seqno with the
now zero rq->global_seqno. This confuses the signaler into action and
signaling the fence.
Add quirks for handling PX/HG systems. In this case, add
a quirk for a weston dGPU that only seems to properly power
down using ATPX power control rather than HG (_PR3).
v2: append a new weston XT
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> (v2) Reviewed-and-Tested-by: Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During eviction, the driver may free more than one hole in the drm_mm
due to the side-effects in evicting the scanned nodes. However,
drm_mm_scan_color_evict() expects that the scan result is the first
available hole (in the mru freed hole_stack list):
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle") Cc: <stable@vger.kernel.org> # v3.19+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2bfa0719ac2a ("usb: gadget: function: f_fs: pass
companion descriptor along") there is a pointer arithmetic
bug where the comp_desc is obtained as follows:
Since ds is a pointer to usb_endpoint_descriptor, adding
7 to it ends up going out of bounds (7 * sizeof(struct
usb_endpoint_descriptor), which is actually 7*9 bytes) past
the SS descriptor. As a result the maxburst value will be
read incorrectly, and the UDC driver will also get a garbage
comp_desc (assuming it uses it).
Since Felipe wrote, "Eventually, f_fs.c should be converted
to use config_ep_by_speed() like all other functions, though",
let's finally do it. This allows the other usb_ep fields to
be properly populated, such as maxpacket and mult. It also
eliminates the awkward speed-based descriptor lookup since
config_ep_by_speed() does that already using the ones found
in struct usb_function.
During _ffs_func_bind(), the received descriptors are evaluated
to prepare for binding with the gadget in order to allocate
endpoints and optionally set up OS descriptors. However, the
high- and super-speed descriptors are only parsed based on
whether the gadget_is_dualspeed() and gadget_is_superspeed()
calls are true, respectively.
This is a problem in case a userspace program always provides
all of the {full,high,super,OS} descriptors when configuring a
function. Then, for example if a gadget device is not capable
of SuperSpeed, the call to ffs_do_descs() for the SS descriptors
is skipped, resulting in an incorrect offset calculation for
the vla_ptr when moving on to the OS descriptors that follow.
This causes ffs_do_os_descs() to fail as it is now looking at
the SS descriptors' offset within the raw_descs buffer instead.
_ffs_func_bind() should evaluate the descriptors unconditionally,
so remove the checks for gadget speed.
Fixes: f0175ab51993 ("usb: gadget: f_fs: OS descriptors support") Cc: stable@vger.kernel.org Co-Developed-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Mayank Rana <mrana@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbac5d07d13e ("usb: musb: host: don't start next rx urb if current one failed")
along with commit b5801212229f ("usb: musb: host: clear rxcsr error bit if set")
try to solve the issue described in [1], but the latter alone is
sufficient, and the former causes the issue as in [2], so now revert it.
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.
Cc: stable@vger.kernel.org Fixes: c2da2ff00606 ("usb: dwc3: ep0: don't use ep0in for transfers") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
commit a8c06e407ef9 ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407ef9 ("usb: separate out sysdev pointer from usb_bus") Signed-off-by: Peter Chen <peter.chen@nxp.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit e10aec652f31 ("drm/edid: Add 6 bpc quirk for display
AEO model 0."), the EDID reports "DFP 1.x compliant TMDS" but it support
6bpc instead of 8 bpc.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Stop printing a (ratelimited) kernel message for each instance of an
unimplemented syscall being called. Userland making an unimplemented
syscall is not necessarily misbehaviour and to be expected with a
current userland running on an older kernel. Also, the current message
looks scary to users but does not actually indicate a real problem nor
help them narrow down the cause. Just rely on sys_ni_syscall() to return
-ENOSYS.
Cc: <stable@vger.kernel.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Weiser <michael.weiser@gmx.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc6031 ("USB: OHCI: don't lose track of EDs when a controller dies") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Aman Deep <aman.deep@samsung.com> Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com> Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff88 ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794ca1 ("cxgb4: Set VPD size so we can read both VPD structures") Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Reviewed-by: Paul Burton <paul.burton@mips.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org Acked-by: Will Deacon <will.deacon@arm.com>, Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported by Sergey Senozhatsky that if THP (Transparent Huge
Page) and frontswap (via zswap) are both enabled, when memory goes low
so that swap is triggered, segfault and memory corruption will occur in
random user space applications as follow,
After bisection, it was found the first bad commit is bd4c82c22c36 ("mm,
THP, swap: delay splitting THP after swapped out").
The root cause is as follows:
When the pages are written to swap device during swapping out in
swap_writepage(), zswap (fontswap) is tried to compress the pages to
improve performance. But zswap (frontswap) will treat THP as a normal
page, so only the head page is saved. After swapping in, tail pages
will not be restored to their original contents, causing memory
corruption in the applications.
This is fixed by refusing to save page in the frontswap store functions
if the page is a THP. So that the THP will be swapped out to swap
device.
Another choice is to split THP if frontswap is enabled. But it is found
that the frontswap enabling isn't flexible. For example, if
CONFIG_ZSWAP=y (cannot be module), frontswap will be enabled even if
zswap itself isn't enabled.
Frontswap has multiple backends, to make it easy for one backend to
enable THP support, the THP checking is put in backend frontswap store
functions instead of the general interfaces.
Link: http://lkml.kernel.org/r/20180209084947.22749-1-ying.huang@intel.com Fixes: bd4c82c22c367e068 ("mm, THP, swap: delay splitting THP after swapped out") Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Suggested-by: Minchan Kim <minchan@kernel.org> [put THP checking in backend] Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Seth Jennings <sjenning@redhat.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Shaohua Li <shli@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Shakeel Butt <shakeelb@google.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: <stable@vger.kernel.org> [4.14] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC-8 shows a warning for the x86 oprofile code that copies per-CPU
data from CPU 0 to all other CPUs, which when building a non-SMP
kernel turns into a memcpy() with identical source and destination
pointers:
arch/x86/oprofile/nmi_int.c: In function 'mux_clone':
arch/x86/oprofile/nmi_int.c:285:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
memcpy(per_cpu(cpu_msrs, cpu).multiplex,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
per_cpu(cpu_msrs, 0).multiplex,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(struct op_msr) * model->num_virt_counters);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/x86/oprofile/nmi_int.c: In function 'nmi_setup':
arch/x86/oprofile/nmi_int.c:466:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
arch/x86/oprofile/nmi_int.c:470:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
I have analyzed a number of such warnings now: some are valid and the
GCC warning is welcome. Others turned out to be false-positives, and
GCC was changed to not warn about those any more. This is a corner case
that is a false-positive but the GCC developers feel it's better to keep
warning about it.
In this case, it seems best to work around it by telling GCC
a little more clearly that this code path is never hit with
an IS_ENABLED() configuration check.
Cc:stable as we also want old kernels to build cleanly with GCC-8.
Build testing with LTO found a couple of files that get compiled
differently depending on whether asm/byteorder.h gets included early
enough or not. In particular, include/asm-generic/qrwlock_types.h is
affected by this, but there are probably others as well.
The symptom is a series of LTO link time warnings, including these:
net/netlabel/netlabel_unlabeled.h:223: error: type of 'netlbl_unlhsh_add' does not match original declaration [-Werror=lto-type-mismatch]
int netlbl_unlhsh_add(struct net *net,
net/netlabel/netlabel_unlabeled.c:377: note: 'netlbl_unlhsh_add' was previously declared here
include/net/ipv6.h:360: error: type of 'ipv6_renew_options_kern' does not match original declaration [-Werror=lto-type-mismatch]
ipv6_renew_options_kern(struct sock *sk,
net/ipv6/exthdrs.c:1162: note: 'ipv6_renew_options_kern' was previously declared here
net/core/dev.c:761: note: 'dev_get_by_name_rcu' was previously declared here
struct net_device *dev_get_by_name_rcu(struct net *net, const char *name)
net/core/dev.c:761: note: code may be misoptimized unless -fno-strict-aliasing is used
drivers/gpu/drm/i915/i915_drv.h:3377: error: type of 'i915_gem_object_set_to_wc_domain' does not match original declaration [-Werror=lto-type-mismatch]
i915_gem_object_set_to_wc_domain(struct drm_i915_gem_object *obj, bool write);
drivers/gpu/drm/i915/i915_gem.c:3639: note: 'i915_gem_object_set_to_wc_domain' was previously declared here
include/linux/debugfs.h:92:9: error: type of 'debugfs_attr_read' does not match original declaration [-Werror=lto-type-mismatch]
ssize_t debugfs_attr_read(struct file *file, char __user *buf,
fs/debugfs/file.c:318: note: 'debugfs_attr_read' was previously declared here
include/linux/rwlock_api_smp.h:30: error: type of '_raw_read_unlock' does not match original declaration [-Werror=lto-type-mismatch]
void __lockfunc _raw_read_unlock(rwlock_t *lock) __releases(lock);
kernel/locking/spinlock.c:246:26: note: '_raw_read_unlock' was previously declared here
include/linux/fs.h:3308:5: error: type of 'simple_attr_open' does not match original declaration [-Werror=lto-type-mismatch]
int simple_attr_open(struct inode *inode, struct file *file,
fs/libfs.c:795: note: 'simple_attr_open' was previously declared here
All of the above are caused by include/asm-generic/qrwlock_types.h
failing to include asm/byteorder.h after commit e0d02285f16e
("locking/qrwlock: Use 'struct qrwlock' instead of 'struct __qrwlock'")
in linux-4.15.
Similar bugs may or may not exist in older kernels as well, but there is
no easy way to test those with link-time optimizations, and kernels
before 4.14 are harder to fix because they don't have Babu's patch
series
We had similar issues with CONFIG_ symbols in the past and ended up
always including the configuration headers though linux/kconfig.h. This
works around the issue through that same file, defining either
__BIG_ENDIAN or __LITTLE_ENDIAN depending on CONFIG_CPU_BIG_ENDIAN,
which is now always set on all architectures since commit 4c97a0c8fee3
("arch: define CPU_BIG_ENDIAN for all fixed big endian archs").
The adis_probe_trigger() creates a new IIO trigger and requests an
interrupt associated with the trigger. The interrupt uses the generic
iio_trigger_generic_data_rdy_poll() function as its interrupt handler.
Currently the driver initializes some fields of the trigger structure after
the interrupt has been requested. But an interrupt can fire as soon as it
has been requested. This opens up a race condition.
iio_trigger_generic_data_rdy_poll() will access the trigger data structure
and dereference the ops field. If the ops field is not yet initialized this
will result in a NULL pointer deref.
It is not expected that the device generates an interrupt at this point, so
typically this issue did not surface unless e.g. due to a hardware
misconfiguration (wrong interrupt number, wrong polarity, etc.).
But some newer devices from the ADIS family start to generate periodic
interrupts in their power-on reset configuration and unfortunately the
interrupt can not be masked in the device. This makes the race condition
much more visible and the following crash has been observed occasionally
when booting a system using the ADIS16460.
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = c0004000
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-04126-gf9739f0-dirty #257
Hardware name: Xilinx Zynq Platform
task: ef04f640 task.stack: ef050000
PC is at iio_trigger_notify_done+0x30/0x68
LR is at iio_trigger_generic_data_rdy_poll+0x18/0x20
pc : [<c042d868>] lr : [<c042d924>] psr: 60000193
sp : ef051bb8 ip : 00000000 fp : ef106400
r10: c081d80a r9 : ef3bfa00 r8 : 00000087
r7 : ef051bec r6 : 00000000 r5 : ef3bfa00 r4 : ee92ab00
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : ee97e400
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xef050210)
[<c042d868>] (iio_trigger_notify_done) from [<c0065b10>] (__handle_irq_event_percpu+0x88/0x118)
[<c0065b10>] (__handle_irq_event_percpu) from [<c0065bbc>] (handle_irq_event_percpu+0x1c/0x58)
[<c0065bbc>] (handle_irq_event_percpu) from [<c0065c30>] (handle_irq_event+0x38/0x5c)
[<c0065c30>] (handle_irq_event) from [<c0068e28>] (handle_level_irq+0xa4/0x130)
[<c0068e28>] (handle_level_irq) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c021ab7c>] (zynq_gpio_irqhandler+0xb8/0x13c)
[<c021ab7c>] (zynq_gpio_irqhandler) from [<c0064e74>] (generic_handle_irq+0x24/0x34)
[<c0064e74>] (generic_handle_irq) from [<c0065370>] (__handle_domain_irq+0x5c/0xb4)
[<c0065370>] (__handle_domain_irq) from [<c000940c>] (gic_handle_irq+0x48/0x8c)
[<c000940c>] (gic_handle_irq) from [<c0013e8c>] (__irq_svc+0x6c/0xa8)
To fix this make sure that the trigger is fully initialized before
requesting the interrupt.
Fixes: ccd2b52f4ac6 ("staging:iio: Add common ADIS library") Reported-by: Robin Getz <Robin.Getz@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no iio buffer has been set up and poll is called return 0.
Without this check there will be a null pointer dereference when
calling poll on a iio driver without an iio buffer.
Cc: stable@vger.kernel.org Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt@axis.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions for triggered buffer support are needed by this module.
If they are not defined accidentally by another driver, there's an error
thrown out while linking.
Add a select of IIO_BUFFER and IIO_TRIGGERED_BUFFER in the Kconfig file.
Error handling in stm32h7_adc_enable routine doesn't unwind enable
sequence correctly. ADEN can only be cleared by hardware (e.g. by
writing one to ADDIS).
It's also better to clear ADRDY just after it's been set by hardware.
Fixes: 95e339b6e85d ("iio: adc: stm32: add support for STM32H7") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
==================================================================
BUG: KASAN: use-after-free in copy_ah_attr_from_uverbs+0x6f2/0x8c0
Read of size 4 at addr ffff88006476a198 by task syzkaller697701/265
There is no matching lock for this mutex. Git history suggests this is
just a missed remnant from an earlier version of the function before
this locking was moved into uverbs_free_xrcd.
Originally this lock was protecting the xrcd_table_delete()
=====================================
WARNING: bad unlock balance detected!
4.15.0+ #87 Not tainted
-------------------------------------
syzkaller223405/269 is trying to release lock (&uverbs_dev->xrcd_tree_mutex) at:
[<00000000b8703372>] ib_uverbs_close_xrcd+0x195/0x1f0
but there are no more locks to release!
other info that might help us debug this:
1 lock held by syzkaller223405/269:
#0: (&uverbs_dev->disassociate_srcu){....}, at: [<000000005af3b960>] ib_uverbs_write+0x265/0xef0
The command number is not bounds checked against the command mask before it
is shifted, resulting in an ubsan hit. This does not cause malfunction since
the command number is eventually bounds checked, but we can make this ubsan
clean by moving the bounds check to before the mask check.
The race is between lookup_get_idr_uobject and
uverbs_idr_remove_uobj -> uverbs_uobject_put.
We deliberately do not call sychronize_rcu after the idr_remove in
uverbs_idr_remove_uobj for performance reasons, instead we call
kfree_rcu() during uverbs_uobject_put.
However, this means we can obtain pointers to uobj's that have
already been released and must protect against krefing them
using kref_get_unless_zero.
==================================================================
BUG: KASAN: use-after-free in copy_ah_attr_from_uverbs.isra.2+0x860/0xa00
Read of size 4 at addr ffff88005fda1ac8 by task syz-executor2/441
Memory state around the buggy address: ffff88005fda1980: fc fc fb fb fb fb fc fc fb fb fb fb fc fc fb fb ffff88005fda1a00: fb fb fc fc fb fb fb fb fc fc 00 00 00 00 fc fc ffff88005fda1a80: fb fb fb fb fc fc fb fb fb fb fc fc fb fb fb fb ffff88005fda1b00: fc fc 00 00 00 00 fc fc fb fb fb fb fc fc fb fb ffff88005fda1b80: fb fb fc fc fb fb fb fb fc fc fb fb fb fb fc fc
==================================================================@
Cc: syzkaller <syzkaller@googlegroups.com> Cc: <stable@vger.kernel.org> # 4.11 Fixes: 3832125624b7 ("IB/core: Add support for idr types") Reported-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some other drivers may be waiting for our extcon to show-up, exiting their
probe methods with -EPROBE_DEFER until we show up.
These drivers will typically get the cable state directly after getting
the extcon, this commit changes the int3496 code to wait for the initial
processing of the id-pin to complete before exiting probe() with 0, which
will cause devices waiting on the defered probe to get reprobed.
This fixes a race where the initial work might still be running while other
drivers were already calling extcon_get_state().
If there is a blacklisted certificate in a SignerInfo's certificate
chain, then pkcs7_verify_sig_chain() sets sinfo->blacklisted and returns
0. But, pkcs7_verify() fails to handle this case appropriately, as it
actually continues on to the line 'actual_ret = 0;', indicating that the
SignerInfo has passed verification. Consequently, PKCS#7 signature
verification ignores the certificate blacklist.
Fix this by not considering blacklisted SignerInfos to have passed
verification.
Also fix the function comment with regards to when 0 is returned.
When pkcs7_verify_sig_chain() is building the certificate chain for a
SignerInfo using the certificates in the PKCS#7 message, it is passing
the wrong arguments to public_key_verify_signature(). Consequently,
when the next certificate is supposed to be used to verify the previous
certificate, the next certificate is actually used to verify itself.
An attacker can use this bug to create a bogus certificate chain that
has no cryptographic relationship between the beginning and end.
Fortunately I couldn't quite find a way to use this to bypass the
overall signature verification, though it comes very close. Here's the
reasoning: due to the bug, every certificate in the chain beyond the
first actually has to be self-signed (where "self-signed" here refers to
the actual key and signature; an attacker might still manipulate the
certificate fields such that the self_signed flag doesn't actually get
set, and thus the chain doesn't end immediately). But to pass trust
validation (pkcs7_validate_trust()), either the SignerInfo or one of the
certificates has to actually be signed by a trusted key. Since only
self-signed certificates can be added to the chain, the only way for an
attacker to introduce a trusted signature is to include a self-signed
trusted certificate.
But, when pkcs7_validate_trust_one() reaches that certificate, instead
of trying to verify the signature on that certificate, it will actually
look up the corresponding trusted key, which will succeed, and then try
to verify the *previous* certificate, which will fail. Thus, disaster
is narrowly averted (as far as I could tell).
Fixes: 6c2dc5ae4ab7 ("X.509: Extract signature digest and make self-signed cert checks earlier") Cc: <stable@vger.kernel.org> # v4.7+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The asymmetric key type allows an X.509 certificate to be added even if
its signature's hash algorithm is not available in the crypto API. In
that case 'payload.data[asym_auth]' will be NULL. But the key
restriction code failed to check for this case before trying to use the
signature, resulting in a NULL pointer dereference in
key_or_keyring_common() or in restrict_link_by_signature().
Fix this by returning -ENOPKG when the signature is unsupported.
Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled and
keyctl has support for the 'restrict_keyring' command:
Fixes: a511e1af8b12 ("KEYS: Move the point of trust determination to __key_link()") Cc: <stable@vger.kernel.org> # v4.7+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The X.509 parser mishandles the case where the certificate's signature's
hash algorithm is not available in the crypto API. In this case,
x509_get_sig_params() doesn't allocate the cert->sig->digest buffer;
this part seems to be intentional. However,
public_key_verify_signature() is still called via
x509_check_for_self_signed(), which triggers the 'BUG_ON(!sig->digest)'.
Fix this by making public_key_verify_signature() return -ENOPKG if the
hash buffer has not been allocated.
Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled:
We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
net/mac80211/cfg.c: In function 'cfg80211_beacon_dup':
net/mac80211/cfg.c:2896:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
From the context, I conclude that we want to copy from beacon into
new_beacon, as we do in the rest of the function.
MIPS' struct compat_flock doesn't match the 32-bit struct flock, as it
has an extra short __unused before pad[4], which combined with alignment
increases the size to 40 bytes compared with struct flock's 36 bytes.
Since commit 8c6657cb50cb ("Switch flock copyin/copyout primitives to
copy_{from,to}_user()"), put_compat_flock() writes the full compat_flock
struct to userland, which results in corruption of the userland word
after the struct flock when running 32-bit userlands on 64-bit kernels.
This was observed to cause a bus error exception when starting Firefox
on Debian 8 (Jessie).
Reported-by: Peter Mamonov <pmamonov@gmail.com> Signed-off-by: James Hogan <jhogan@kernel.org> Tested-by: Peter Mamonov <pmamonov@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.13+
Patchwork: https://patchwork.linux-mips.org/patch/18646/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fcp_rsp_info structure as defined in the FC spec has an initial 3
bytes reserved field. The ibmvfc driver mistakenly defined this field as
4 bytes resulting in the rsp_code field being defined in what should be
the start of the second reserved field and thus always being reported as
zero by the driver.
Ideally, we should wire ibmvfc up with libfc for the sake of code
deduplication, and ease of maintaining standardized structures in a
single place. However, for now simply fixup the definition in ibmvfc for
backporting to distros on older kernels. Wiring up with libfc will be
done in a followup patch.
Cc: <stable@vger.kernel.org> Reported-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xtensa memory initialization code frees high memory pages without
checking whether they are in the reserved memory regions or not. That
results in invalid value of totalram_pages and duplicate page usage by
CMA and highmem. It produces a bunch of BUGs at startup looking like
this:
The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.
The failure was:
Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
FATAL ERROR: Unable to parse input tree
/usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
/usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com> Fixes: 28128c61e08e ("kconfig.h: Include compiler types to avoid missed struct attributes") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header files for some structures could get included in such a way
that struct attributes (specifically __randomize_layout from path.h) would
be parsed as variable names instead of attributes. This could lead to
some instances of a structure being unrandomized, causing nasty GPFs, etc.
This patch makes sure the compiler_types.h header is included in
kconfig.h so that we've always got types and struct attributes defined,
since kconfig.h is included from the compiler command line.
Reported-by: Patrick McLean <chutzpah@gentoo.org> Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Fixes: 3859a271a003 ("randstruct: Mark various structs for randomization") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ard Biesheuvel [Fri, 23 Feb 2018 18:29:02 +0000 (18:29 +0000)]
arm64: mm: don't write garbage into TTBR1_EL1 register
Stable backport commit 173358a49173 ("arm64: kpti: Add ->enable callback
to remap swapper using nG mappings") of upstream commit f992b4dfd58b did
not survive the backporting process unscathed, and ends up writing garbage
into the TTBR1_EL1 register, rather than pointing it to the zero page to
disable translations. Fix that.
Cc: <stable@vger.kernel.org> #v4.14 Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Syzbot reported a possible deadlock in the netfilter area caused by
rtnl lock, xt lock and socket lock being acquired with a different order
on different code paths, leading to the following backtrace: Reviewed-by: Xin Long <lucien.xin@gmail.com>
======================================================
WARNING: possible circular locking dependency detected
4.15.0+ #301 Not tainted
------------------------------------------------------
syzkaller233489/4179 is trying to acquire lock:
(rtnl_mutex){+.+.}, at: [<0000000048e996fd>] rtnl_lock+0x17/0x20
net/core/rtnetlink.c:74
but task is already holding lock:
(&xt[i].mutex){+.+.}, at: [<00000000328553a2>]
xt_find_table_lock+0x3e/0x3e0 net/netfilter/x_tables.c:1041
which lock already depends on the new lock.
===
Since commit 3f34cfae1230 ("netfilter: on sockopt() acquire sock lock
only in the required scope"), we already acquire the socket lock in
the innermost scope, where needed. In such commit I forgot to remove
the outer-most socket lock from the getsockopt() path, this commit
addresses the issues dropping it now.
v1 -> v2: fix bad subj, added relavant 'fixes' tag
Fixes: 22265a5c3c10 ("netfilter: xt_TEE: resolve oif using netdevice notifiers") Fixes: 202f59afd441 ("netfilter: ipt_CLUSTERIP: do not hold dev") Fixes: 3f34cfae1230 ("netfilter: on sockopt() acquire sock lock only in the required scope") Reported-by: syzbot+ddde1c7b7ff7442d7f2d@syzkaller.appspotmail.com Suggested-by: Florian Westphal <fw@strlen.de> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log