Input: cyttsp - set abs params for ABS_MT_TOUCH_MAJOR
The driver is certainly reporting pressure in cyttsp_report_tchdata()
with input_report_abs(input, ABS_MT_TOUCH_MAJOR, tch->z); so we should
also advertise this capability.
When I test to use the CY8CTMA340 with PostmarketOS I don't have any
problem whatsoever in dropping this phys path, it finds and uses the
touchscreen just as well. I suppose it is because userspace is using
modern input libraries.
I challenge the maintainers to point out a valid and still used
userspace that actually need this. I say we drop it.
The data sheet for CY8CTMA340 specifies that the reset pulse shall be at
least 1 ms. Specify 1-2 ms with usleep_range() to cut some slack for the
scheduler.
Curiously the datasheet does not specify how long we have to wait after a
hard reset until the chip is up, but I have found a vendor tree (Samsung
GT-S7710) that has code for this touch screen and there this is set to 5
ms so I use this with the same 1 ms fuzz.
Input: mms114 - convert bindings to YAML and extend
This converts the Melfas MMS114 bindings and extend like this:
- Require nodename touchscreen@ (this seems to be the case for
all in-tree DTS files)
- Add the mms134s and mms136 compatibles
- Add the avdd and vdd power supplies
- Define the I2C clock frequency property
Vincent Knecht [Fri, 9 Apr 2021 20:29:03 +0000 (13:29 -0700)]
Input: add MStar MSG2638 touchscreen driver
Add support for the msg2638 touchscreen IC from MStar.
Firmware handling, wakeup gestures and other specialties are not supported.
This driver reuses zinitix.c structure, while the checksum and irq handler
functions are based on out-of-tree driver for Alcatel Idol 3 (4.7").
Hans de Goede [Sat, 10 Apr 2021 05:29:49 +0000 (22:29 -0700)]
Input: silead - add workaround for x86 BIOS-es which bring the chip up in a stuck state
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
Hans de Goede [Sat, 10 Apr 2021 05:29:07 +0000 (22:29 -0700)]
Input: elants_i2c - do not bind to i2c-hid compatible ACPI instantiated devices
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
Input: gpio-keys - fix crash when disabliing GPIO-less buttons
My brain-damaged adjustments to Paul's patch caused crashes in
gpio_keys_disable_button() when driver is used in GPIO-less (i.e.
purely interrupt-driven) setups, because I mixed together debounce and
release timers when they are in fact separate:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
...
PC is at hrtimer_active+0xc/0x98
LR is at hrtimer_try_to_cancel+0x24/0x140
...
[<c01c43b8>] (hrtimer_active) from [<c01c50f4>] (hrtimer_try_to_cancel+0x24/0x140)
[<c01c50f4>] (hrtimer_try_to_cancel) from [<c01c5224>] (hrtimer_cancel+0x14/0x4c)
[<c01c5224>] (hrtimer_cancel) from [<bf1cae24>] (gpio_keys_attr_store_helper+0x1b8/0x1d8 [gpio_keys])
[<bf1cae24>] (gpio_keys_attr_store_helper [gpio_keys]) from [<bf1cae80>] (gpio_keys_store_disabled_keys+0x18/0x24 [gpio_keys])
[<bf1cae80>] (gpio_keys_store_disabled_keys [gpio_keys]) from [<c038ec7c>] (kernfs_fop_write_iter+0x10c/0x1cc)
[<c038ec7c>] (kernfs_fop_write_iter) from [<c02df858>] (vfs_write+0x2ac/0x404)
[<c02df858>] (vfs_write) from [<c02dfaf4>] (ksys_write+0x64/0xdc)
[<c02dfaf4>] (ksys_write) from [<c0100080>] (ret_fast_syscall+0x0/0x58)
Let's fix it up.
Fixes: c9efb0ba281e ("Input: gpio-keys - use hrtimer for software debounce, if possible") Reported-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/YG1DFFgojSVfdpaz@google.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Barry Song [Thu, 25 Mar 2021 21:43:18 +0000 (14:43 -0700)]
Input: move to use request_irq by IRQF_NO_AUTOEN flag
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
On the other hand, request_irq() after setting IRQ_NOAUTOEN as
below
irq_set_status_flags(irq, IRQ_NOAUTOEN);
request_irq(dev, irq...);
can also be replaced by request_irq() with IRQF_NO_AUTOEN flag.
Linus Walleij [Tue, 23 Mar 2021 03:25:26 +0000 (20:25 -0700)]
Input: cyttsp - verbose error on soft reset
The first thing the Cypress driver does when starting
up is to try a soft reset. This is the first point where
the driver SPI/I2C communication can fail, so put out some
nice debug text:
Jeff LaBundy [Tue, 23 Mar 2021 03:16:40 +0000 (20:16 -0700)]
dt-bindings: input: iqs5xx: Convert to YAML
This patch converts the legacy text-based binding document to YAML
format. Extraneous details and touchscreen properties that weren't
actually supported have been dropped.
The reset GPIO has since been made optional in the driver; this is
now reflected here as well.
Jeff LaBundy [Tue, 23 Mar 2021 03:15:32 +0000 (20:15 -0700)]
Input: iqs5xx - make reset GPIO optional
The device's hardware reset pin is only required if the platform
must be able to update the device's firmware.
As such, demote the reset GPIO to optional in support of devices
that ship with pre-programmed firmware and don't route the reset
pin back to the SoC.
In that case, the 'fw_file' attribute is hidden because there is
no way to open the bootloader. The logic is extended to the case
in which the device does not advertise bootloader support in the
first place.
Last but not least, remove the hardware reset performed at probe
because there is no reason to reset the device manually. A power
on reset function already ensures a clean reset at start-up.
Jeff LaBundy [Mon, 22 Mar 2021 23:43:00 +0000 (16:43 -0700)]
Input: touchscreen - broaden use-cases described in comments
Now that the helper functions have been moved to drivers/input/ so
that all input devices may use them, the introductory comments can
be updated to remove any implication that the helper functions are
solely limited to touchscreens.
This patch also scrubs any remaining use of 'DT' since there isn't
any actual dependency on OF. A minor spelling error is resolved as
well ('setups' -> 'sets up').
Jeff LaBundy [Mon, 22 Mar 2021 23:42:25 +0000 (16:42 -0700)]
Input: touchscreen - move helper functions to core
Some devices outside of drivers/input/touchscreen/ can still make
use of the touchscreen helper functions. Therefore, it was agreed
in [1] to move them outside of drivers/input/touchscreen/ so that
other devices can call them without INPUT_TOUCHSCREEN being set.
As part of this change, 'of' is dropped from the filename because
the helpers no longer actually use OF. No changes are made to the
file contents whatsoever.
Based on the feedback in [2], the corresponding binding documents
(touchscreen.yaml and touchscreen.txt) are left in their original
locations.
Jeff LaBundy [Mon, 22 Mar 2021 04:04:17 +0000 (21:04 -0700)]
Input: iqs5xx - close bootloader using hardware reset
The bootloader can be closed using the 'execute' command (0x02) or
hardware reset. Rather than using the former option for successful
firmware update procedures and reserving the latter for recovering
the device upon failure, simply use hardware reset for all cases.
The post-bootloader initialization delay increases marginally when
triggered by a hardware reset, so increase the wait time to ensure
the device does not subsequently fail to respond.
As part of this change, refactor the return path to avoid an extra
assignment and to make the logic a bit smaller.
The vendor-assigned firmware project number is restricted to the
generic project number (15); however the vendor may assign other
project numbers to specific applications and customers.
These custom project numbers may be based on forwards-compatible
firmware revision 1.x. However, the driver unnecessarily rejects
anything older than firmware revision 2.0.
To support other applications, remove these unnecessarily strict
checks and enter the bootloader only for truly incompatible A000
devices.
Jeff LaBundy [Mon, 22 Mar 2021 04:02:11 +0000 (21:02 -0700)]
Input: iqs5xx - expose firmware revision to user space
Add the read-only 'fw_info' attribute which reports information
about the device's firmware in the following format:
a.b.c.d:e.f
Where:
a = Product number (e.g. 40 for IQS550)
b = Project number (e.g. 15)
c = Firmware revision (major)
d = Firmware revision (minor)
e = Customer-assigned exported file version (major)
f = Customer-assigned exported file version (minor)
As part of the corresponding rework to uses of 'bl_status', the
IQS5XX_BL_STATUS_RESET definition is dropped with 0 used in its
place instead.
Jeff LaBundy [Mon, 22 Mar 2021 04:01:35 +0000 (21:01 -0700)]
Input: iqs5xx - optimize axis definition and validation
Set the maximum ABS_MT_PRESSURE value and use the existing U16_MAX
definition instead of a magic number to validate ABS_MT_POSITION_X
and ABS_MT_POSITION_Y.
Also use input_set_abs_params() rather than input_abs_set_max() to
avoid having to call input_set_capability() separately.
Paul Cercueil [Sun, 21 Mar 2021 23:09:29 +0000 (16:09 -0700)]
Input: gpio-keys - use hrtimer for software debounce, if possible
We want to be able to report the input event as soon as the debounce
delay elapsed. However, the current code does not really ensure that,
as it uses the jiffies-based schedule_delayed_work() API. With a small
enough HZ value (HZ <= 100), this results in some input events being
lost, when a key is quickly pressed then released (on a human's time
scale).
Switching to hrtimers fixes this issue, and will work even on extremely
low HZ values (tested at HZ=24). This is however only possible if
reading the GPIO is possible without sleeping. If this condition is not
met, the previous approach of using a jiffies-based timer is taken.
Paul Cercueil [Sun, 21 Mar 2021 23:06:34 +0000 (16:06 -0700)]
Input: gpio-keys - use hrtimer for release timer
Dealing with input, timing is important; if the button should be
released in one millisecond, then it should be done in one millisecond
and not a hundred milliseconds.
Therefore, the standard timer API is not really suitable for this task.
Convert the gpio-keys driver to use a hrtimer instead of the standard
timer to address this issue.
Note that by using a hard IRQ for the hrtimer callback, we can get rid
of the spin_lock_irqsave() and spin_unlock_irqrestore().
Paul Cercueil [Sun, 21 Mar 2021 23:06:23 +0000 (16:06 -0700)]
Input: gpio-keys - remove extra call to input_sync
The input_sync() function is already called after the loop in
gpio_keys_report_state(), so it does not need to be called after each
iteration within gpio_keys_gpio_report_event().
Uwe Kleine-König [Sun, 21 Mar 2021 22:24:12 +0000 (15:24 -0700)]
Input: max8997 - simplify open coding of a division using up to 64 divisions
The for loop is just a complicate way to express a division. Replace it
by the actual division which is both simpler to understand for a human
and more efficient for a CPU to calculate.
Linus Torvalds [Sun, 21 Mar 2021 21:06:10 +0000 (14:06 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Miscellaneous ext4 bug fixes for v5.12"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: initialize ret to suppress smatch warning
ext4: stop inode update before return
ext4: fix rename whiteout with fast commit
ext4: fix timer use-after-free on failed mount
ext4: fix potential error in ext4_do_update_inode
ext4: do not try to set xattr into ea_inode if value is empty
ext4: do not iput inode under running transaction in ext4_rename()
ext4: find old entry again if failed to rename whiteout
ext4: fix error handling in ext4_end_enable_verity()
ext4: fix bh ref count on error paths
fs/ext4: fix integer overflow in s_log_groups_per_flex
ext4: add reclaim checks to xattr code
ext4: shrink race window in ext4_should_retry_alloc()
Linus Torvalds [Sun, 21 Mar 2021 19:25:54 +0000 (12:25 -0700)]
Merge tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block
Pull io_uring followup fixes from Jens Axboe:
- The SIGSTOP change from Eric, so we properly ignore that for
PF_IO_WORKER threads.
- Disallow sending signals to PF_IO_WORKER threads in general, we're
not interested in having them funnel back to the io_uring owning
task.
- Stable fix from Stefan, ensuring we properly break links for short
send/sendmsg recv/recvmsg if MSG_WAITALL is set.
- Catch and loop when needing to run task_work before a PF_IO_WORKER
threads goes to sleep.
* tag 'io_uring-5.12-2021-03-21' of git://git.kernel.dk/linux-block:
io_uring: call req_set_fail_links() on short send[msg]()/recv[msg]() with MSG_WAITALL
io-wq: ensure task is running before processing task_work
signal: don't allow STOP on PF_IO_WORKER threads
signal: don't allow sending any signals to PF_IO_WORKER threads
Linus Torvalds [Sun, 21 Mar 2021 18:54:04 +0000 (11:54 -0700)]
Merge tag 'staging-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Some small staging and IIO driver fixes:
- MAINTAINERS changes for the move of the staging mailing list
- comedi driver fixes to get request_irq() to work correctly
- counter driver fixes for reported issues with iio devices
- tiny iio driver fixes for reported issues.
All of these have been in linux-next with no reported problems"
* tag 'staging-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt665x: fix alignment constraints
staging: comedi: cb_pcidas64: fix request_irq() warn
staging: comedi: cb_pcidas: fix request_irq() warn
MAINTAINERS: move the staging subsystem to lists.linux.dev
MAINTAINERS: move some real subsystems off of the staging mailing list
iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
iio: hid-sensor-temperature: Fix issues of timestamp channel
iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
counter: stm32-timer-cnt: fix ceiling write max value
counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
iio: adc: ab8500-gpadc: Fix off by 10 to 3
iio:adc:stm32-adc: Add HAS_IOMEM dependency
iio: adis16400: Fix an error code in adis16400_initial_setup()
iio: adc: adi-axi-adc: add proper Kconfig dependencies
iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
iio: hid-sensor-prox: Fix scale not correct issue
iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel
Linus Torvalds [Sun, 21 Mar 2021 18:49:16 +0000 (11:49 -0700)]
Merge tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt driver fixes from Greg KH:
"Here are some small Thunderbolt and USB driver fixes for some reported
issues:
- thunderbolt fixes for minor problems
- typec fixes for power issues
- usb-storage quirk addition
- usbip bugfix
- dwc3 bugfix when stopping transfers
- cdnsp bugfix for isoc transfers
- gadget use-after-free fix
All have been in linux-next this week with no reported issues"
* tag 'usb-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tcpm: Skip sink_cap query only when VDM sm is busy
usb: dwc3: gadget: Prevent EP queuing while stopping transfers
usb: typec: tcpm: Invoke power_supply_changed for tcpm-source-psy-
usb: typec: Remove vdo[3] part of tps6598x_rx_identity_reg struct
usb-storage: Add quirk to defeat Kindle's automatic unload
usb: gadget: configfs: Fix KASAN use-after-free
usbip: Fix incorrect double assignment to udc->ud.tcp_rx
usb: cdnsp: Fixes incorrect value in ISOC TRB
thunderbolt: Increase runtime PM reference count on DP tunnel discovery
thunderbolt: Initialize HopID IDAs in tb_switch_alloc()
Linus Torvalds [Sun, 21 Mar 2021 18:34:24 +0000 (11:34 -0700)]
Merge tag 'irq-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"A change to robustify force-threaded IRQ handlers to always disable
interrupts, plus a DocBook fix.
The force-threaded IRQ handler change has been accelerated from the
normal schedule of such a change to keep the bad pattern/workaround of
spin_lock_irqsave() in handlers or IRQF_NOTHREAD as a kludge from
spreading"
* tag 'irq-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Disable interrupts for force threaded handlers
genirq/irq_sim: Fix typos in kernel doc (fnode -> fwnode)
Linus Torvalds [Sun, 21 Mar 2021 18:26:21 +0000 (11:26 -0700)]
Merge tag 'perf-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Boundary condition fixes for bugs unearthed by the perf fuzzer"
* tag 'perf-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix unchecked MSR access error caused by VLBR_EVENT
perf/x86/intel: Fix a crash caused by zero PEBS status
Linus Torvalds [Sun, 21 Mar 2021 18:11:22 +0000 (11:11 -0700)]
Merge tag 'efi-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
- another missing RT_PROP table related fix, to ensure that the
efivarfs pseudo filesystem fails gracefully if variable services
are unsupported
- use the correct alignment for literal EFI GUIDs
- fix a use after unmap issue in the memreserve code
* tag 'efi-urgent-2021-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: use 32-bit alignment for efi_guid_t literals
firmware/efi: Fix a use after bug in efi_mem_reserve_persistent
efivars: respect EFI_UNSUPPORTED return from firmware
Linus Torvalds [Sun, 21 Mar 2021 18:04:20 +0000 (11:04 -0700)]
Merge tag 'x86_urgent_for_v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"The freshest pile of shiny x86 fixes for 5.12:
- Add the arch-specific mapping between physical and logical CPUs to
fix devicetree-node lookups
- Restore the IRQ2 ignore logic
- Fix get_nr_restart_syscall() to return the correct restart syscall
number. Split in a 4-patches set to avoid kABI breakage when
backporting to dead kernels"
* tag 'x86_urgent_for_v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/of: Fix CPU devicetree-node lookups
x86/ioapic: Ignore IRQ2 again
x86: Introduce restart_block->arch_data to remove TS_COMPAT_RESTART
x86: Introduce TS_COMPAT_RESTART to fix get_nr_restart_syscall()
x86: Move TS_COMPAT back to asm/thread_info.h
kernel, fs: Introduce and use set_restart_fn() and arch_set_restart_data()
Linus Torvalds [Sun, 21 Mar 2021 17:57:35 +0000 (10:57 -0700)]
Merge tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a possible stack corruption and subsequent DLPAR failure in the
rpadlpar_io PCI hotplug driver
- Two build fixes for uncommon configurations
Thanks to Christophe Leroy and Tyrel Datwyler.
* tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
PCI: rpadlpar: Fix potential drc_name corruption in store functions
powerpc: Force inlining of cpu_has_feature() to avoid build failure
powerpc/vdso32: Add missing _restgpr_31_x to fix build failure
Jens Axboe [Sun, 21 Mar 2021 13:06:56 +0000 (07:06 -0600)]
io-wq: ensure task is running before processing task_work
Mark the current task as running if we need to run task_work from the
io-wq threads as part of work handling. If that is the case, then return
as such so that the caller can appropriately loop back and reset if it
was part of a going-to-sleep flush.
Fixes: 3bfe6106693b ("io-wq: fork worker threads from original task") Signed-off-by: Jens Axboe <axboe@kernel.dk>
Eric W. Biederman [Sun, 21 Mar 2021 15:37:48 +0000 (09:37 -0600)]
signal: don't allow STOP on PF_IO_WORKER threads
Just like we don't allow normal signals to IO threads, don't deliver a
STOP to a task that has PF_IO_WORKER set. The IO threads don't take
signals in general, and have no means of flushing out a stop either.
Longer term, we may want to look into allowing stop of these threads,
as it relates to eg process freezing. For now, this prevents a spin
issue if a SIGSTOP is delivered to the parent task.
Reported-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Jens Axboe [Sat, 20 Mar 2021 01:25:13 +0000 (19:25 -0600)]
signal: don't allow sending any signals to PF_IO_WORKER threads
They don't take signals individually, and even if they share signals with
the parent task, don't allow them to be delivered through the worker
thread. Linux does allow this kind of behavior for regular threads, but
it's really a compatability thing that we need not care about for the IO
threads.
Reported-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Harshad Shirwadkar [Tue, 16 Mar 2021 22:19:21 +0000 (15:19 -0700)]
ext4: fix rename whiteout with fast commit
This patch adds rename whiteout support in fast commits. Note that the
whiteout object that gets created is actually char device. Which
imples, the function ext4_inode_journal_mode(struct inode *inode)
would return "JOURNAL_DATA" for this inode. This has a consequence in
fast commit code that it will make creation of the whiteout object a
fast-commit ineligible behavior and thus will fall back to full
commits. With this patch, this can be observed by running fast commits
with rename whiteout and seeing the stats generated by ext4_fc_stats
tracepoint as follows:
ext4_fc_stats: dev 254:32 fc ineligible reasons:
XATTR:0, CROSS_RENAME:0, JOURNAL_FLAG_CHANGE:0, NO_MEM:0, SWAP_BOOT:0,
RESIZE:0, RENAME_DIR:0, FALLOC_RANGE:0, INODE_JOURNAL_DATA:16;
num_commits:6, ineligible: 6, numblks: 3
So in short, this patch guarantees that in case of rename whiteout, we
fall back to full commits.
Amir mentioned that instead of creating a new whiteout object for
every rename, we can create a static whiteout object with irrelevant
nlink. That will make fast commits to not fall back to full
commit. But until this happens, this patch will ensure correctness by
falling back to full commits.
Jan Kara [Mon, 15 Mar 2021 16:59:06 +0000 (17:59 +0100)]
ext4: fix timer use-after-free on failed mount
When filesystem mount fails because of corrupted filesystem we first
cancel the s_err_report timer reminding fs errors every day and only
then we flush s_error_work. However s_error_work may report another fs
error and re-arm timer thus resulting in timer use-after-free. Fix the
problem by first flushing the work and only after that canceling the
s_err_report timer.
Reported-by: syzbot+628472a2aac693ab0fcd@syzkaller.appspotmail.com Fixes: 2d01ddc86606 ("ext4: save error info to sb through journal if available") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210315165906.2175-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu>
zhangyi (F) [Fri, 5 Mar 2021 12:05:08 +0000 (20:05 +0800)]
ext4: do not try to set xattr into ea_inode if value is empty
Syzbot report a warning that ext4 may create an empty ea_inode if set
an empty extent attribute to a file on the file system which is no free
blocks left.
Now, ext4 try to store extent attribute into an external inode if
ext4_xattr_block_set() return -ENOSPC, but for the case of store an
empty extent attribute, store the extent entry into the extent
attribute block is enough. A simple reproduce below.
zhangyi (F) [Wed, 3 Mar 2021 13:17:03 +0000 (21:17 +0800)]
ext4: do not iput inode under running transaction in ext4_rename()
In ext4_rename(), when RENAME_WHITEOUT failed to add new entry into
directory, it ends up dropping new created whiteout inode under the
running transaction. After commit <9b88f9fb0d2> ("ext4: Do not iput inode
under running transaction"), we follow the assumptions that evict() does
not get called from a transaction context but in ext4_rename() it breaks
this suggestion. Although it's not a real problem, better to obey it, so
this patch add inode to orphan list and stop transaction before final
iput().
zhangyi (F) [Wed, 3 Mar 2021 13:17:02 +0000 (21:17 +0800)]
ext4: find old entry again if failed to rename whiteout
If we failed to add new entry on rename whiteout, we cannot reset the
old->de entry directly, because the old->de could have moved from under
us during make indexed dir. So find the old entry again before reset is
needed, otherwise it may corrupt the filesystem as below.
/dev/sda: Entry '00000001' in ??? (12) has deleted/unused inode 15. CLEARED.
/dev/sda: Unattached inode 75
/dev/sda: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
Dmitry Osipenko [Sun, 21 Mar 2021 02:23:44 +0000 (19:23 -0700)]
Input: atmel_mxt_ts - support wakeup methods
According to datasheets, chips like mXT1386 have a WAKE line, it is used
to wake the chip up from deep sleep mode before communicating with it via
the I2C-compatible interface.
If the WAKE line is connected to a GPIO line, the line must be asserted
25 ms before the host attempts to communicate with the controller. If the
WAKE line is connected to the SCL pin, the controller will send a NACK on
the first attempt to address it, the host must then retry 25 ms later.
Implement the wake-up methods in the driver. Touchscreen now works
properly on devices like Acer A500 tablet, fixing problems like this:
Dmitry Osipenko [Sun, 21 Mar 2021 02:19:58 +0000 (19:19 -0700)]
dt-bindings: input: atmel_mxt_ts: Document atmel,wakeup-method and WAKE line GPIO
Some Atmel touchscreen controllers have a WAKE line that needs to be
asserted low in order to wake up controller from a deep sleep. Document
the wakeup methods and the new GPIO properties.
Thomas Gleixner [Wed, 17 Mar 2021 14:38:52 +0000 (15:38 +0100)]
genirq: Disable interrupts for force threaded handlers
With interrupt force threading all device interrupt handlers are invoked
from kernel threads. Contrary to hard interrupt context the invocation only
disables bottom halfs, but not interrupts. This was an oversight back then
because any code like this will have an issue:
This has been triggered with networking (NAPI vs. hrtimers) and console
drivers where printk() happens from an interrupt which interrupted the
force threaded handler.
Now people noticed and started to change the spin_lock() in the handler to
spin_lock_irqsave() which affects performance or add IRQF_NOTHREAD to the
interrupt request which in turn breaks RT.
Fix the root cause and not the symptom and disable interrupts before
invoking the force threaded handler which preserves the regular semantics
and the usefulness of the interrupt force threading as a general debugging
tool.
For not RT this is not changing much, except that during the execution of
the threaded handler interrupts are delayed until the handler
returns. Vs. scheduling and softirq processing there is no difference.
For RT kernels there is no issue.
Fixes: 8d32a307e4fa ("genirq: Provide forced interrupt threading") Reported-by: Johan Hovold <johan@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Johan Hovold <johan@kernel.org> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20210317143859.513307808@linutronix.de
Linus Torvalds [Sat, 20 Mar 2021 18:01:54 +0000 (11:01 -0700)]
Merge tag 'riscv-for-linus-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of fixes for 5.12:
- fix the SBI remote fence numbers for hypervisor fences, which had
been transcribed in the wrong order in Linux. These fences are only
used with the KVM patches applied.
- fix a whole host of build warnings, these should have no functional
change.
- fix init_resources() to prevent an off-by-one error from causing an
out-of-bounds array reference. This was manifesting during boot on
vexriscv.
- ensure the KASAN mappings are visible before proceeding to use
them"
* tag 'riscv-for-linus-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Correct SPARSEMEM configuration
RISC-V: kasan: Declare kasan_shallow_populate() static
riscv: Ensure page table writes are flushed when initializing KASAN vmalloc
RISC-V: Fix out-of-bounds accesses in init_resources()
riscv: Fix compilation error with Canaan SoC
ftrace: Fix spelling mistake "disabed" -> "disabled"
riscv: fix bugon.cocci warnings
riscv: process: Fix no prototype for arch_dup_task_struct
riscv: ftrace: Use ftrace_get_regs helper
riscv: process: Fix no prototype for show_regs
riscv: syscall_table: Reduce W=1 compilation warnings noise
riscv: time: Fix no prototype for time_init
riscv: ptrace: Fix no prototype warnings
riscv: sbi: Fix comment of __sbi_set_timer_v01
riscv: irq: Fix no prototype warning
riscv: traps: Fix no prototype warnings
RISC-V: correct enum sbi_ext_rfence_fid
Linus Torvalds [Sat, 20 Mar 2021 18:00:25 +0000 (11:00 -0700)]
Merge tag '5.12-rc3-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five cifs/smb3 fixes - three for stable, including an important ACL
fix and security signature fix"
* tag '5.12-rc3-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix allocation size on newly created files
cifs: warn and fail if trying to use rootfs without the config option
fs/cifs/: fix misspellings using codespell tool
cifs: Fix preauth hash corruption
cifs: update new ACE pointer after populate_new_aces.
Linus Torvalds [Sat, 20 Mar 2021 17:57:10 +0000 (10:57 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight fixes, all in drivers, all fairly minor either being fixes in
error legs, memory leaks on teardown, context errors or semantic
problems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: Do not use GFP_KERNEL in atomic context
scsi: ufs: ufs-mediatek: Correct operator & -> &&
scsi: sd_zbc: Update write pointer offset cache
scsi: lpfc: Fix some error codes in debugfs
scsi: qla2xxx: Fix broken #endif placement
scsi: st: Fix a use after free in st_open()
scsi: myrs: Fix a double free in myrs_cleanup()
scsi: ibmvfc: Free channel_setup_buf during device tear down
Linus Torvalds [Sat, 20 Mar 2021 00:32:30 +0000 (17:32 -0700)]
Merge tag 'zonefs-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fixes from Damien Le Moal:
- fix inode write open reference count (Chao)
- Fix wrong write offset for asynchronous O_APPEND writes (me)
- Prevent use of sequential zone file as swap files (me)
* tag 'zonefs-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: fix to update .i_wr_refcnt correctly in zonefs_open_zone()
zonefs: Fix O_APPEND async write handling
zonefs: prevent use of seq files as swap file
Linus Torvalds [Sat, 20 Mar 2021 00:07:10 +0000 (17:07 -0700)]
Merge tag 'block-5.12-2021-03-19' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Just an NVMe pull request this week:
- fix tag allocation for keep alive
- fix a unit mismatch for the Write Zeroes limits
- various TCP transport fixes (Sagi Grimberg, Elad Grupi)
- fix iosqes and iocqes validation for discovery controllers (Sagi Grimberg)"
* tag 'block-5.12-2021-03-19' of git://git.kernel.dk/linux-block:
nvmet-tcp: fix kmap leak when data digest in use
nvmet: don't check iosqes,iocqes for discovery controllers
nvme-rdma: fix possible hang when failing to set io queues
nvme-tcp: fix possible hang when failing to set io queues
nvme-tcp: fix misuse of __smp_processor_id with preemption enabled
nvme-tcp: fix a NULL deref when receiving a 0-length r2t PDU
nvme: fix Write Zeroes limitations
nvme: allocate the keep alive request using BLK_MQ_REQ_NOWAIT
nvme: merge nvme_keep_alive into nvme_keep_alive_work
nvme-fabrics: only reserve a single tag
Linus Torvalds [Sat, 20 Mar 2021 00:01:09 +0000 (17:01 -0700)]
Merge tag 'io_uring-5.12-2021-03-19' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Quieter week this time, which was both expected and desired. About
half of the below is fixes for this release, the other half are just
fixes in general. In detail:
- Fix the freezing of IO threads, by making the freezer not send them
fake signals. Make them freezable by default.
- Like we did for personalities, move the buffer IDR to xarray. Kills
some code and avoids a use-after-free on teardown.
- SQPOLL cleanups and fixes (Pavel)
- Fix linked timeout race (Pavel)
- Fix potential completion post use-after-free (Pavel)
- Cleanup and move internal structures outside of general kernel view
(Stefan)
- Use MSG_SIGNAL for send/recv from io_uring (Stefan)"
* tag 'io_uring-5.12-2021-03-19' of git://git.kernel.dk/linux-block:
io_uring: don't leak creds on SQO attach error
io_uring: use typesafe pointers in io_uring_task
io_uring: remove structures from include/linux/io_uring.h
io_uring: imply MSG_NOSIGNAL for send[msg]()/recv[msg]() calls
io_uring: fix sqpoll cancellation via task_work
io_uring: add generic callback_head helpers
io_uring: fix concurrent parking
io_uring: halt SQO submission on ctx exit
io_uring: replace sqd rw_semaphore with mutex
io_uring: fix complete_post use ctx after free
io_uring: fix ->flags races by linked timeouts
io_uring: convert io_buffer_idr to XArray
io_uring: allow IO worker threads to be frozen
kernel: freezer should treat PF_IO_WORKER like PF_KTHREAD for freezing
Johan Hovold [Fri, 12 Mar 2021 09:20:33 +0000 (10:20 +0100)]
x86/apic/of: Fix CPU devicetree-node lookups
Architectures that describe the CPU topology in devicetree and do not have
an identity mapping between physical and logical CPU ids must override the
default implementation of arch_match_cpu_phys_id().
Failing to do so breaks CPU devicetree-node lookups using of_get_cpu_node()
and of_cpu_device_node_get() which several drivers rely on. It also causes
the CPU struct devices exported through sysfs to point to the wrong
devicetree nodes.
On x86, CPUs are described in devicetree using their APIC ids and those
do not generally coincide with the logical ids, even if CPU0 typically
uses APIC id 0.
Add the missing implementation of arch_match_cpu_phys_id() so that CPU-node
lookups work also with SMP.
Apart from fixing the broken sysfs devicetree-node links this likely does
not affect current users of mainline kernels on x86.
Linus Torvalds [Fri, 19 Mar 2021 21:10:07 +0000 (14:10 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Fixes for kvm on x86:
- new selftests
- fixes for migration with HyperV re-enlightenment enabled
- fix RCU/SRCU usage
- fixes for local_irq_restore misuse false positive"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
documentation/kvm: additional explanations on KVM_SET_BOOT_CPU_ID
x86/kvm: Fix broken irq restoration in kvm_wait
KVM: X86: Fix missing local pCPU when executing wbinvd on all dirty pCPUs
KVM: x86: Protect userspace MSR filter with SRCU, and set atomically-ish
selftests: kvm: add set_boot_cpu_id test
selftests: kvm: add _vm_ioctl
selftests: kvm: add get_msr_index_features
selftests: kvm: Add basic Hyper-V clocksources tests
KVM: x86: hyper-v: Don't touch TSC page values when guest opted for re-enlightenment
KVM: x86: hyper-v: Track Hyper-V TSC page status
KVM: x86: hyper-v: Prevent using not-yet-updated TSC page by secondary CPUs
KVM: x86: hyper-v: Limit guest to writing zero to HV_X64_MSR_TSC_EMULATION_STATUS
KVM: x86/mmu: Store the address space ID in the TDP iterator
KVM: x86/mmu: Factor out tdp_iter_return_to_root
KVM: x86/mmu: Fix RCU usage when atomically zapping SPTEs
KVM: x86/mmu: Fix RCU usage in handle_removed_tdp_mmu_page
Linus Torvalds [Fri, 19 Mar 2021 21:07:19 +0000 (14:07 -0700)]
Merge tag 'gpio-fixes-for-v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"Two fixes for the GPIO subsystem. Both address issues in the core GPIO
code:
- fix the return value in error path in gpiolib_dev_init()
- fix the 'gpio-line-names' property handling correctly this time"
* tag 'gpio-fixes-for-v5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: Assign fwnode to parent's if no primary one provided
gpiolib: Fix error return code in gpiolib_dev_init()
Linus Torvalds [Fri, 19 Mar 2021 18:39:28 +0000 (11:39 -0700)]
Merge tag 's390-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- disable preemption when accessing local per-cpu variables in the new
counter set driver
- fix by a factor of four increased steal time due to missing
cputime_to_nsecs() conversion
- fix PCI device structure leak
* tag 's390-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix leak of PCI device structure
s390/vtime: fix increased steal time accounting
s390/cpumf: disable preemption when accessing per-cpu variable
Linus Torvalds [Fri, 19 Mar 2021 17:06:30 +0000 (10:06 -0700)]
Merge tag 'trace-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull workqueue tracing fix from Steven Rostedt:
"Fix workqueue trace event unsafe string reference
After adding a verifier to test all strings printed in trace events to
make sure they either point to a string on the ring buffer, or to read
only core kernel memory, it triggered on a workqueue trace event. The
trace event workqueue_queue_work references the allocated name of the
workqueue in the output. If the workqueue is freed before the trace is
read, then the trace will dereference freed memory.
Update the trace event to use the __string(), __assign_str(), and
__get_str() helpers to handle such cases"
* tag 'trace-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
workqueue/tracing: Copy workqueue name to buffer in trace event
Linus Torvalds [Fri, 19 Mar 2021 17:00:10 +0000 (10:00 -0700)]
Merge tag 'pm-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Revert two problematic commits.
Specifics:
- Revert ACPI PM commit that attempted to improve reboot handling on
some systems, but it caused other systems to panic() during reboot
(Josef Bacik)
- Revert PM-runtime commit that attempted to improve the handling of
suppliers during PM-runtime suspend of a consumer device, but it
introduced a race condition potentially leading to unexpected
behavior (Rafael Wysocki)"
* tag 'pm-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM: runtime: Update device status before letting suppliers suspend"
Revert "PM: ACPI: reboot: Use S5 for reboot"
Linus Torvalds [Fri, 19 Mar 2021 16:56:04 +0000 (09:56 -0700)]
Merge tag 'iommu-fixes-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Three AMD IOMMU patches to fix a boot crash on AMD Stoney systems and
every other AMD IOMMU system booted with 'amd_iommu=off'.
This is a v5.11 regression.
- A Fix for the Tegra IOMMU driver to make sure it detects all IOMMUs
* tag 'iommu-fixes-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/tegra-smmu: Make tegra_smmu_probe_device() to handle all IOMMU phandles
iommu/amd: Keep track of amd_iommu_irq_remap state
iommu/amd: Don't call early_amd_iommu_init() when AMD IOMMU is disabled
iommu/amd: Move Stoney Ridge check to detect_ivrs()
Linus Torvalds [Fri, 19 Mar 2021 16:53:32 +0000 (09:53 -0700)]
Merge tag 'sound-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The majority of changes are various ASoC device/platform-specific
small fixes (including a removal of stale file) while the only common
change is a clk management fix in ASoC simple-card driver.
The rest are the usual HD-audio quirks"
* tag 'sound-5.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (44 commits)
ALSA: usb-audio: Fix unintentional sign extension issue
ALSA: hda/realtek: fix mute/micmute LEDs for HP 850 G8
ASoC: dt-bindings: fsl_spdif: Add compatible string for new platforms
ASoC: rt711: add snd_soc_component remove callback
ASoC: rt5659: Update MCLK rate in set_sysclk()
ASoC: simple-card-utils: Do not handle device clock
ALSA: hda/realtek: fix mute/micmute LEDs for HP 440 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP 840 G8
ALSA: hda/realtek: apply pin quirk for XiaomiNotebook Pro
ALSA: hda/realtek: Apply headset-mic quirks for Xiaomi Redmibook Air
ASoC: mediatek: mt8192: fix tdm out data is valid on rising edge
ALSA: dice: fix null pointer dereference when node is disconnected
ALSA: hda: generic: Fix the micmute led init state
ASoC: qcom: lpass-cpu: Fix lpass dai ids parse
spi: cadence: set cqspi to the driver_data field of struct device
ASoC: SOF: intel: fix wrong poll bits in dsp power down
ASoC: codecs: wcd934x: add a sanity check in set channel map
ASoC: qcom: sdm845: Fix array out of range on rx slim channels
ASoC: qcom: sdm845: Fix array out of bounds access
ASoC: remove remnants of sirf prima/atlas audio codec
...
Steve French [Fri, 19 Mar 2021 05:05:48 +0000 (00:05 -0500)]
cifs: fix allocation size on newly created files
Applications that create and extend and write to a file do not
expect to see 0 allocation size. When file is extended,
set its allocation size to a plausible value until we have a
chance to query the server for it. When the file is cached
this will prevent showing an impossible number of allocated
blocks (like 0). This fixes e.g. xfstests 614 which does
1) create a file and set its size to 64K
2) mmap write 64K to the file
3) stat -c %b for the file (to query the number of allocated blocks)
It was failing because we returned 0 blocks. Even though we would
return the correct cached file size, we returned an impossible
allocation size.
Signed-off-by: Steve French <stfrench@microsoft.com> CC: <stable@vger.kernel.org> Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Rafael J. Wysocki [Fri, 19 Mar 2021 14:47:25 +0000 (15:47 +0100)]
Revert "PM: runtime: Update device status before letting suppliers suspend"
Revert commit 44cc89f76464 ("PM: runtime: Update device status
before letting suppliers suspend") that introduced a race condition
into __rpm_callback() which allowed a concurrent rpm_resume() to
run and resume the device prematurely after its status had been
changed to RPM_SUSPENDED by __rpm_callback().
Fixes: 44cc89f76464 ("PM: runtime: Update device status before letting suppliers suspend") Link: https://lore.kernel.org/linux-pm/24dfb6fc-5d54-6ee2-9195-26428b7ecf8a@intel.com/ Reported-by: Adrian Hunter <adrian.hunter@intel.com> Cc: 4.10+ <stable@vger.kernel.org> # 4.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Ingo Molnar [Fri, 19 Mar 2021 13:23:46 +0000 (14:23 +0100)]
Merge tag 'efi-urgent-for-v5.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/urgent
Pull EFI fixes from Ard Biesheuvel:
"- another missing RT_PROP table related fix, to ensure that the efivarfs
pseudo filesystem fails gracefully if variable services are unsupported
- use the correct alignment for literal EFI GUIDs
- fix a use after unmap issue in the memreserve code"
Jens Axboe [Fri, 19 Mar 2021 12:40:47 +0000 (06:40 -0600)]
Merge tag 'nvme-5.12-20210319' of git://git.infradead.org/nvme into block-5.12
Pull NVMe updates from Christoph:
"nvme fixes for 5.12
- fix tag allocation for keep alive
- fix a unit mismatch for the Write Zeroes limits
- various TCP transport fixes (Sagi Grimberg, Elad Grupi)
- fix iosqes and iocqes validation for discovery controllers (Sagi Grimberg)"
* tag 'nvme-5.12-20210319' of git://git.infradead.org/nvme:
nvmet-tcp: fix kmap leak when data digest in use
nvmet: don't check iosqes,iocqes for discovery controllers
nvme-rdma: fix possible hang when failing to set io queues
nvme-tcp: fix possible hang when failing to set io queues
nvme-tcp: fix misuse of __smp_processor_id with preemption enabled
nvme-tcp: fix a NULL deref when receiving a 0-length r2t PDU
nvme: fix Write Zeroes limitations
nvme: allocate the keep alive request using BLK_MQ_REQ_NOWAIT
nvme: merge nvme_keep_alive into nvme_keep_alive_work
nvme-fabrics: only reserve a single tag
Sites that match init_section_contains() get marked as INIT. For
built-in code init_sections contains both __init and __exit text. OTOH
kernel_text_address() only explicitly includes __init text (and there
are no __exit text markers).
Match what jump_label already does and ignore the warning for INIT
sites. Also see the excellent changelog for commit: 8f35eaa5f2de
("jump_label: Don't warn on __exit jump entries")
The intent is to avoid writing init code after init (because the text
might have been freed). The code is needlessly different between
jump_label and static_call and not obviously correct.
The existing code relies on the fact that the module loader clears the
init layout, such that within_module_init() always fails, while
jump_label relies on the module state which is more obvious and
matches the kernel logic.
Thomas Gleixner [Thu, 18 Mar 2021 19:26:47 +0000 (20:26 +0100)]
x86/ioapic: Ignore IRQ2 again
Vitaly ran into an issue with hotplugging CPU0 on an Amazon instance where
the matrix allocator claimed to be out of vectors. He analyzed it down to
the point that IRQ2, the PIC cascade interrupt, which is supposed to be not
ever routed to the IO/APIC ended up having an interrupt vector assigned
which got moved during unplug of CPU0.
The underlying issue is that IRQ2 for various reasons (see commit af174783b925 ("x86: I/O APIC: Never configure IRQ2" for details) is treated
as a reserved system vector by the vector core code and is not accounted as
a regular vector. The Amazon BIOS has an routing entry of pin2 to IRQ2
which causes the IO/APIC setup to claim that interrupt which is granted by
the vector domain because there is no sanity check. As a consequence the
allocation counter of CPU0 underflows which causes a subsequent unplug to
fail with:
[ ... ] CPU 0 has 4294967295 vectors, 589 available. Cannot disable CPU
There is another sanity check missing in the matrix allocator, but the
underlying root cause is that the IO/APIC code lost the IRQ2 ignore logic
during the conversion to irqdomains.
For almost 6 years nobody complained about this wreckage, which might
indicate that this requirement could be lifted, but for any system which
actually has a PIC IRQ2 is unusable by design so any routing entry has no
effect and the interrupt cannot be connected to a device anyway.
Due to that and due to history biased paranoia reasons restore the IRQ2
ignore logic and treat it as non existent despite a routing entry claiming
otherwise.
Fixes: d32932d02e18 ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces") Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210318192819.636943062@linutronix.de
Ard Biesheuvel [Wed, 10 Mar 2021 07:33:19 +0000 (08:33 +0100)]
efi: use 32-bit alignment for efi_guid_t literals
Commit 494c704f9af0 ("efi: Use 32-bit alignment for efi_guid_t") updated
the type definition of efi_guid_t to ensure that it always appears
sufficiently aligned (the UEFI spec is ambiguous about this, but given
the fact that its EFI_GUID type is defined in terms of a struct carrying
a uint32_t, the natural alignment is definitely >= 32 bits).
However, we missed the EFI_GUID() macro which is used to instantiate
efi_guid_t literals: that macro is still based on the guid_t type,
which does not have a minimum alignment at all. This results in warnings
such as
In file included from drivers/firmware/efi/mokvar-table.c:35:
include/linux/efi.h:1093:34: warning: passing 1-byte aligned argument to
4-byte aligned parameter 2 of 'get_var' may result in an unaligned pointer
access [-Walign-mismatch]
status = get_var(L"SecureBoot", &EFI_GLOBAL_VARIABLE_GUID, NULL, &size,
^
include/linux/efi.h:1101:24: warning: passing 1-byte aligned argument to
4-byte aligned parameter 2 of 'get_var' may result in an unaligned pointer
access [-Walign-mismatch]
get_var(L"SetupMode", &EFI_GLOBAL_VARIABLE_GUID, NULL, &size, &setupmode);
The distinction only matters on CPUs that do not support misaligned loads
fully, but 32-bit ARM's load-multiple instructions fall into that category,
and these are likely to be emitted by the compiler that built the firmware
for loading word-aligned 128-bit GUIDs from memory
So re-implement the initializer in terms of our own efi_guid_t type, so that
the alignment becomes a property of the literal's type.
Fixes: 494c704f9af0 ("efi: Use 32-bit alignment for efi_guid_t") Reported-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Link: https://github.com/ClangBuiltLinux/linux/issues/1327 Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Linus Torvalds [Fri, 19 Mar 2021 00:57:34 +0000 (17:57 -0700)]
Merge tag 'drm-fixes-2021-03-19' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular fixes pull, pretty small set of fixes, a couple of i915 and
amdgpu, one ttm, one nouveau and one omap. Probably smaller than usual
for this time, so we'll see if something pops up next week or if this
will continue to stay small.
Summary:
ttm:
- Make ttm_bo_unpin() not wraparound on too many unpins
i915:
- Workaround async flip + VT-d frame corruption on HSW/BDW
- Fix NMI watchdog crash due to uninitialized OA buffer use on gen12+
nouveau:
- workaround oops with bo syncing"
* tag 'drm-fixes-2021-03-19' of git://anongit.freedesktop.org/drm/drm:
nouveau: Skip unvailable ttm page entries
drm/amd/display: Remove MPC gamut remap logic for DCN30
drm/amd/display: Correct algorithm for reversed gamma
drm/omap: dsi: fix unsigned expression compared with zero
i915/perf: Start hrtimer only if sampling the OA buffer
drm/i915: Workaround async flip + VT-d corruption on HSW/BDW
drm/amd/display: Copy over soc values before bounding box creation
drm/ttm: make ttm_bo_unpin more defensive
The underlying problem is not introduced by the commit, yet it uncovered the
underlying issue. The cited commit relies on valid pages. This is not given for
due to some bugs. For now, just warn and work around the issue by just ignoring
the bad ttm objects.
Below is some debug info gathered while debugging this issue:
nouveau 0000:01:00.0: DRM: ttm_dma->num_pages: 2048
nouveau 0000:01:00.0: DRM: ttm_dma->pages is NULL
nouveau 0000:01:00.0: DRM: ttm_dma: 00000000e96058e7
nouveau 0000:01:00.0: DRM: ttm_dma->page_flags:
nouveau 0000:01:00.0: DRM: ttm_dma: Populated: 1
nouveau 0000:01:00.0: DRM: ttm_dma: No Retry: 0
nouveau 0000:01:00.0: DRM: ttm_dma: SG: 256
nouveau 0000:01:00.0: DRM: ttm_dma: Zero Alloc: 0
nouveau 0000:01:00.0: DRM: ttm_dma: Swapped: 0
Dave Airlie [Fri, 19 Mar 2021 00:33:32 +0000 (10:33 +1000)]
Merge tag 'drm-intel-fixes-2021-03-18' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.12-rc4:
- Workaround async flip + VT-d frame corruption on HSW/BDW
- Fix NMI watchdog crash due to uninitialized OA buffer use on gen12+
projects / users / jedix / linux-maple.git / log