During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the burst len fixup after setting the generic value for it. This
finally enables the fixup introduced by commit 137bd11090d8 ("dmaengine:
pl330: Align DMA memcpy operations to MFIFO width"), which otherwise was
overwritten by the generic value.
Reported-by: kernel test robot <lkp@intel.com> Fixes: 137bd11090d8 ("dmaengine: pl330: Align DMA memcpy operations to MFIFO width") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20200825064617.16193-1-m.szyprowski@samsung.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba03d ("net: arc_emac: support the phy reset for emac driver") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8eb6 ("net: systemport: Dynamically allocate number of TX rings") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aaf1b ("net: hns: net: hns: enet adds support of acpi") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Note the non-zero upper bits of the first element. It turns out that
nft_immediate doesn't zero the destination register, but this is needed
when the length isn't a multiple of 4.
Furthermore, the zeroing in nft_payload is broken. We can't use
[len / 4] = 0 -- if len is a multiple of 4, index is off by one.
Skip zeroing in this case and use a conditional instead of (len -1) / 4.
Fixes: 49499c3e6e18 ("netfilter: nf_tables: switch registers to 32 bit addressing") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel sends an empty NFTA_SET_USERDATA attribute with no value if
userspace adds a set with no NFTA_SET_USERDATA attribute.
Fixes: e6d8ecac9e68 ("netfilter: nf_tables: Add new attributes into nft_set to store user data.") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initialization done by bmips_cpu_setup() typically affects both
threads of a given core, on 7435 which supports 2 cores and 2 threads,
logical CPU number 2 and 3 would not run this initialization.
Fixes: 738a3f79027b ("MIPS: BMIPS: Add early CPU initialization code") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the BMIPS generic cpu-feature-overrides.h file was introduced,
cpu_has_inclusive_caches/MIPS_CPU_INCLUSIVE_CACHES was not set for
BMIPS5000 CPUs. Correct this when we have initialized the MIPS secondary
cache successfully.
batadv_bla_send_claim() gets called from worker thread context through
batadv_bla_periodic_work(), thus netif_rx_ni needs to be used in that
case. This fixes "NOHZ: local_softirq_pending 08" log messages seen
when batman-adv is enabled.
Fixes: 23721387c409 ("batman-adv: add basic bridge loop avoidance code") Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The own OGM check is currently misplaced and can lead to the following
issues:
For one thing we might receive an aggregated OGM from a neighbor node
which has our own OGM in the first place. We would then not only skip
our own OGM but erroneously also any other, following OGM in the
aggregate.
For another, we might receive an OGM aggregate which has our own OGM in
a place other then the first one. Then we would wrongly not skip this
OGM, leading to populating the orginator and gateway table with ourself.
The gateway client code can try to optimize the delivery of DHCP packets to
avoid broadcasting them through the whole mesh. But also transmissions to
the client can be optimized by looking up the destination via the chaddr of
the DHCP packet.
But the chaddr is currently only done when chaddr is fully inside the
non-paged area of the skbuff. Otherwise it will not be initialized and the
unoptimized path should have been taken.
But the implementation didn't handle this correctly. It didn't retrieve the
correct chaddr but still tried to perform the TT lookup with this
uninitialized memory.
Reported-by: syzbot+ab16e463b903f5a37036@syzkaller.appspotmail.com Fixes: 6c413b1c22a2 ("batman-adv: send every DHCP packet as bat-unicast") Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some architectures (like ARM), virt_to_gfn cannot be used for
vmalloc'd memory because of its reliance on virt_to_phys. This patch
introduces a check for vmalloc'd addresses and obtains the PFN using
vmalloc_to_pfn in that case.
Since commit a21ee6055c30 ("lockdep: Change hardirq{s_enabled,_context}
to per-cpu variables") the lockdep code itself uses percpu variables. This
leads to recursions because the percpu macros are calling preempt_enable()
which might call trace_preempt_on().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Marco Elver <elver@google.com> Link: https://lkml.kernel.org/r/20200821085348.251340558@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Leases don't currently work correctly on kcephfs, as they are not broken
when caps are revoked. They could eventually be implemented similarly to
how we did them in libcephfs, but for now don't allow them.
[ idryomov: no need for simple_nosetlease() in ceph_dir_fops and
ceph_snapdir_fops ]
clang static analysis reports this representative problem
applesmc.c:758:10: warning: 1st function call argument is an
uninitialized value
left = be16_to_cpu(*(__be16 *)(buffer + 6)) >> 2;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
buffer is filled by the earlier call
ret = applesmc_read_key(LIGHT_SENSOR_LEFT_KEY, ...
This problem is reported because a goto skips the status check.
Other similar problems use data from applesmc_read_key before checking
the status. So move the checks to before the use.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Henrik Rydberg <rydberg@bitmath.org> Link: https://lore.kernel.org/r/20200820131932.10590-1-trix@redhat.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Define shutdown callback for display drm driver,
so as to disable all the CRTCS when shutdown
notification is received by the driver.
This change will turn off the timing engine so
that no display transactions are requested
while mmu translations are getting disabled
during reboot sequence.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Changes in v2:
- Remove NULL check from msm_pdev_shutdown (Stephen Boyd)
- Change commit text to reflect when this issue
was uncovered (Sai Prakash Ranjan)
Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booting with heavily modularized config, the serial console
may not be able to load until after init when modules that
satisfy needed dependencies have time to load.
Unfortunately, as qcom_geni_console_setup is marked as __init,
the function may have been freed before we get to run it,
causing boot time crashes such as:
(scatter|gather)_data_area() need to flush dcache after writing data to or
before reading data from a page in uio data area. The two routines are
able to handle data transfer to/from such a page in fragments and flush the
cache after each fragment was copied by calling the wrapper
tcmu_flush_dcache_range().
That means:
1) flush_dcache_page() can be called multiple times for the same page.
2) Calling flush_dcache_page() indirectly using the wrapper does not make
sense, because each call of the wrapper is for one single page only and
the calling routine already has the correct page pointer.
Change (scatter|gather)_data_area() such that, instead of calling
tcmu_flush_dcache_range() before/after each memcpy, it now calls
flush_dcache_page() before unmapping a page (when writing is complete for
that page) or after mapping a page (when starting to read the page).
After this change only calls to tcmu_flush_dcache_range() for addresses in
vmalloc'ed command ring are left over.
The patch was tested on ARM with kernel 4.19.118 and 5.7.2
Link: https://lore.kernel.org/r/20200618131632.32748-2-bstroesser@ts.fujitsu.com Tested-by: JiangYu <lnsyyj@hotmail.com> Tested-by: Daniel Meyerholt <dxm523@gmail.com> Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) If remaining ring space before the end of the ring is smaller then the
next cmd to write, tcmu writes a padding entry which fills the remaining
space at the end of the ring.
Then tcmu calls tcmu_flush_dcache_range() with the size of struct
tcmu_cmd_entry as data length to flush. If the space filled by the
padding was smaller then tcmu_cmd_entry, tcmu_flush_dcache_range() is
called for an address range reaching behind the end of the vmalloc'ed
ring.
tcmu_flush_dcache_range() in a loop calls
flush_dcache_page(virt_to_page(start)); for every page being part of the
range. On x86 the line is optimized out by the compiler, as
flush_dcache_page() is empty on x86.
But I assume the above can cause trouble on other architectures that
really have a flush_dcache_page(). For paddings only the header part of
an entry is relevant due to alignment rules the header always fits in
the remaining space, if padding is needed. So tcmu_flush_dcache_range()
can safely be called with sizeof(entry->hdr) as the length here.
2) After it has written a command to cmd ring, tcmu calls
tcmu_flush_dcache_range() using the size of a struct tcmu_cmd_entry as
data length to flush. But if a command needs many iovecs, the real size
of the command may be bigger then tcmu_cmd_entry, so a part of the
written command is not flushed then.
Link: https://lore.kernel.org/r/20200528193108.9085-1-bstroesser@ts.fujitsu.com Acked-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Event modifiers are not mentioned in the perf record or perf stat
manpages. Add them to orient new users more effectively by pointing
them to the perf list manpage for details.
Fixes: 2055fdaf8703 ("perf list: Document precise event sampling for AMD IBS") Signed-off-by: Kim Phillips <kim.phillips@amd.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul Clarke <pc@us.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Tony Jones <tonyj@suse.de> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20200901215853.276234-1-kim.phillips@amd.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling into hid_map_usage(), the passed event code is
blindly stored as is, even if it doesn't fit in the associated bitmap.
This event code can come from a variety of sources, including devices
masquerading as input devices, only a bit more "programmable".
Instead of taking the event code at face value, check that it actually
fits the corresponding bitmap, and if it doesn't:
- spit out a warning so that we know which device is acting up
- NULLify the bitmap pointer so that we catch unexpected uses
Code paths that can make use of untrusted inputs can now check
that the mapping was indeed correct and bail out if not.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that a ReportSize value of zero is legal, even if a bit
non-sensical. Most of the HID code seems to handle that gracefully,
except when computing the total size in bytes. When fed as input to
memset, this leads to some funky outcomes.
Detect the corner case and correctly compute the size.
Cc: stable@vger.kernel.org Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org Reported-by: Stefan Berger <stefanb@linux.ibm.com> Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
With my new locking code dbench is so much faster that I tripped over a
transaction abort from ENOSPC. This turned out to be because
btrfs_del_dir_entries_in_log was checking for ret == -ENOSPC, but this
function sets err on error, and returns err. So instead of properly
marking the inode as needing a full commit, we were returning -ENOSPC
and aborting in __btrfs_unlink_inode. Fix this by checking the proper
variable so that we return the correct thing in the case of ENOSPC.
The ENOENT needs to be checked, because btrfs_lookup_dir_item_index()
can return -ENOENT if the dir item isn't in the tree log (which would
happen if we hadn't fsync'ed this guy). We actually handle that case in
__btrfs_unlink_inode, so it's an expected error to get back.
Fixes: 4a500fd178c8 ("Btrfs: Metadata ENOSPC handling for tree log") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add note and comment about ENOENT ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Brooke Basile <brookebasile@gmail.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Brooke Basile <brookebasile@gmail.com> Acked-by: Felipe Balbi <balbi@kernel.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com> Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Cyril Roelandt <tipecaml@gmail.com> Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
There's another Raydium touchscreen needs the no-lpm quirk:
[ 1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[ 1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.339151] usb 1-9: Product: Raydium Touch System
[ 1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[ 6.450497] usb 1-9: can't set config #1, error -110
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:
The values for "se_num" and "sh_num" come from the user in the ioctl.
They can be in the 0-255 range but if they're more than
AMDGPU_GFX_MAX_SE (4) or AMDGPU_GFX_MAX_SH_PER_SE (2) then it results in
an out of bounds read.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc4461e7 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain") Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org # v4.18+ Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.
The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027fffff799 ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.
Add a check for the cpumask being empty to prevent this.
When the primary firmware node pointer is removed from a
device (set to NULL) the secondary firmware node pointer,
when it exists, is made the primary node for the device.
However, the secondary firmware node pointer of the original
primary firmware node is never cleared (set to NULL).
To avoid situation where the secondary firmware node pointer
is pointing to a non-existing object, clearing it properly
when the primary node is removed from a device in
set_primary_fwnode().
Fixes: 97badf873ab6 ("device property: Make it possible to use secondary firmware nodes") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been reported that system-wide suspend may be aborted in the
absence of any wakeup events due to unforseen interactions of it with
the runtume PM framework.
One failing scenario is when there are multiple devices sharing an
ACPI power resource and runtime-resume needs to be carried out for
one of them during system-wide suspend (for example, because it needs
to be reconfigured before the whole system goes to sleep). In that
case, the runtime-resume of that device involves turning the ACPI
power resource "on" which in turn causes runtime-resume requests
to be queued up for all of the other devices sharing it. Those
requests go to the runtime PM workqueue which is frozen during
system-wide suspend, so they are not actually taken care of until
the resume of the whole system, but the pm_runtime_barrier()
call in __device_suspend() sees them and triggers system wakeup
events for them which then cause the system-wide suspend to be
aborted if wakeup source objects are in active use.
Of course, the logic that leads to triggering those wakeup events is
questionable in the first place, because clearly there are cases in
which a pending runtime resume request for a device is not connected
to any real wakeup events in any way (like the one above). Moreover,
it is racy, because the device may be resuming already by the time
the pm_runtime_barrier() runs and so if the driver doesn't take care
of signaling the wakeup event as appropriate, it will be lost.
However, if the driver does take care of that, the extra
pm_wakeup_event() call in the core is redundant.
Accordingly, drop the conditional pm_wakeup_event() call fron
__device_suspend() and make the latter call pm_runtime_barrier()
alone. Also modify the comment next to that call to reflect the new
code and extend it to mention the need to avoid unwanted interactions
between runtime PM and system-wide device suspend callbacks.
Fixes: 1e2ef05bb8cf8 ("PM: Limit race conditions between runtime PM and system sleep (v2)") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com> Tested-by: Utkarsh H Patel <utkarsh.h.patel@intel.com> Tested-by: Pengfei Xu <pengfei.xu@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
handler data is meant for interrupt handlers and not for storing irq chip
specific information as some devices require handler data to store internal
per interrupt information, e.g. pinctrl/GPIO chained interrupt handlers.
This obviously creates a conflict of interests and crashes the machine
because the XEN pointer is overwritten by the driver pointer.
As the XEN data is not handler specific it should be stored in
irqdesc::irq_data::chip_data instead.
A simple sed s/irq_[sg]et_handler_data/irq_[sg]et_chip_data/ cures that.
Cc: stable@vger.kernel.org Reported-by: Roman Shaposhnik <roman@zededa.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Roman Shaposhnik <roman@zededa.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/87lfi2yckt.fsf@nanos.tec.linutronix.de Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are processing writeback for sync(2), move_expired_inodes()
didn't set any inode expiry value (older_than_this). This can result in
writeback never completing if there's steady stream of inodes added to
b_dirty_time list as writeback rechecks dirty lists after each writeback
round whether there's more work to be done. Fix the problem by using
sync(2) start time is inode expiry value when processing b_dirty_time
list similarly as for ordinarily dirtied inodes. This requires some
refactoring of older_than_this handling which simplifies the code
noticeably as a bonus.
Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") CC: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inode's i_io_list list head is used to attach inode to several different
lists - wb->{b_dirty, b_dirty_time, b_io, b_more_io}. When flush worker
prepares a list of inodes to writeback e.g. for sync(2), it moves inodes
to b_io list. Thus it is critical for sync(2) data integrity guarantees
that inode is not requeued to any other writeback list when inode is
queued for processing by flush worker. That's the reason why
writeback_single_inode() does not touch i_io_list (unless the inode is
completely clean) and why __mark_inode_dirty() does not touch i_io_list
if I_SYNC flag is set.
However there are two flaws in the current logic:
1) When inode has only I_DIRTY_TIME set but it is already queued in b_io
list due to sync(2), concurrent __mark_inode_dirty(inode, I_DIRTY_SYNC)
can still move inode back to b_dirty list resulting in skipping
writeback of inode time stamps during sync(2).
2) When inode is on b_dirty_time list and writeback_single_inode() races
with __mark_inode_dirty() like:
writeback_single_inode() __mark_inode_dirty(inode, I_DIRTY_PAGES)
inode->i_state |= I_SYNC
__writeback_single_inode()
inode->i_state |= I_DIRTY_PAGES;
if (inode->i_state & I_SYNC)
bail
if (!(inode->i_state & I_DIRTY_ALL))
- not true so nothing done
We end up with I_DIRTY_PAGES inode on b_dirty_time list and thus
standard background writeback will not writeback this inode leading to
possible dirty throttling stalls etc. (thanks to Martijn Coenen for this
analysis).
Fix these problems by tracking whether inode is queued in b_io or
b_more_io lists in a new I_SYNC_QUEUED flag. When this flag is set, we
know flush worker has queued inode and we should not touch i_io_list.
On the other hand we also know that once flush worker is done with the
inode it will requeue the inode to appropriate dirty list. When
I_SYNC_QUEUED is not set, __mark_inode_dirty() can (and must) move inode
to appropriate dirty list.
Reported-by: Martijn Coenen <maco@android.com> Reviewed-by: Martijn Coenen <maco@android.com> Tested-by: Martijn Coenen <maco@android.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, operations on inode->i_io_list are protected by
wb->list_lock. In the following patches we'll need to maintain
consistency between inode->i_state and inode->i_io_list so change the
code so that inode->i_lock protects also all inode's i_io_list handling.
Reviewed-by: Martijn Coenen <maco@android.com> Reviewed-by: Christoph Hellwig <hch@lst.de> CC: stable@vger.kernel.org # Prerequisite for "writeback: Avoid skipping inode writeback" Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f12e ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f12e ("serial: pl011: add console matching function") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.10+ Cc: Aleksey Makarov <amakarov@marvell.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Christopher Covington <cov@codeaurora.org> Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl
to save struct vc_data values that are modified and restore the original
values in case of error.
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Add a check to fbcon_resize() to ensure that a possible change to user font
height or user font width will not allow a font data out-of-bounds access.
NOTE: must use original charcount in calculation as font charcount can
change and cannot be used to determine the font data allocated size.
If a transaction aborts it can cause a memory leak of the pages array of
a block group's io_ctl structure. The following steps explain how that can
happen:
1) Transaction N is committing, currently in state TRANS_STATE_UNBLOCKED
and it's about to start writing out dirty extent buffers;
2) Transaction N + 1 already started and another task, task A, just called
btrfs_commit_transaction() on it;
3) Block group B was dirtied (extents allocated from it) by transaction
N + 1, so when task A calls btrfs_start_dirty_block_groups(), at the
very beginning of the transaction commit, it starts writeback for the
block group's space cache by calling btrfs_write_out_cache(), which
allocates the pages array for the block group's io_ctl with a call to
io_ctl_init(). Block group A is added to the io_list of transaction
N + 1 by btrfs_start_dirty_block_groups();
4) While transaction N's commit is writing out the extent buffers, it gets
an IO error and aborts transaction N, also setting the file system to
RO mode;
5) Task A has already returned from btrfs_start_dirty_block_groups(), is at
btrfs_commit_transaction() and has set transaction N + 1 state to
TRANS_STATE_COMMIT_START. Immediately after that it checks that the
filesystem was turned to RO mode, due to transaction N's abort, and
jumps to the "cleanup_transaction" label. After that we end up at
btrfs_cleanup_one_transaction() which calls btrfs_cleanup_dirty_bgs().
That helper finds block group B in the transaction's io_list but it
never releases the pages array of the block group's io_ctl, resulting in
a memory leak.
In fact at the point when we are at btrfs_cleanup_dirty_bgs(), the pages
array points to pages that were already released by us at
__btrfs_write_out_cache() through the call to io_ctl_drop_pages(). We end
up freeing the pages array only after waiting for the ordered extent to
complete through btrfs_wait_cache_io(), which calls io_ctl_free() to do
that. But in the transaction abort case we don't wait for the space cache's
ordered extent to complete through a call to btrfs_wait_cache_io(), so
that's why we end up with a memory leak - we wait for the ordered extent
to complete indirectly by shutting down the work queues and waiting for
any jobs in them to complete before returning from close_ctree().
We can solve the leak simply by freeing the pages array right after
releasing the pages (with the call to io_ctl_drop_pages()) at
__btrfs_write_out_cache(), since we will never use it anymore after that
and the pages array points to already released pages at that point, which
is currently not a problem since no one will use it after that, but not a
good practice anyway since it can easily lead to use-after-free issues.
So fix this by freeing the pages array right after releasing the pages at
__btrfs_write_out_cache().
This issue can often be reproduced with test case generic/475 from fstests
and kmemleak can detect it and reports it with the following trace:
SCHED_RESTART code path is relied to re-run queue for dispatch requests
in hctx->dispatch. Meantime the SCHED_RSTART flag is checked when adding
requests to hctx->dispatch.
memory barriers have to be used for ordering the following two pair of OPs:
1) adding requests to hctx->dispatch and checking SCHED_RESTART in
blk_mq_dispatch_rq_list()
2) clearing SCHED_RESTART and checking if there is request in hctx->dispatch
in blk_mq_sched_restart().
Without the added memory barrier, either:
1) blk_mq_sched_restart() may miss requests added to hctx->dispatch meantime
blk_mq_dispatch_rq_list() observes SCHED_RESTART, and not run queue in
dispatch side
or
2) blk_mq_dispatch_rq_list still sees SCHED_RESTART, and not run queue
in dispatch side, meantime checking if there is request in
hctx->dispatch from blk_mq_sched_restart() is missed.
IO hang in ltp/fs_fill test is reported by kernel test robot:
https://lkml.org/lkml/2020/7/26/77
Turns out it is caused by the above out-of-order OPs. And the IO hang
can't be observed any more after applying this patch.
Fixes: bd166ef183c2 ("blk-mq-sched: add framework for MQ capable IO schedulers") Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Cc: David Jeffery <djeffery@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this commit i2c_hid_parse() consists of the following steps:
1. Send power on cmd
2. usleep_range(1000, 5000)
3. Send reset cmd
4. Wait for reset to complete (device interrupt, or msleep(100))
5. Send power on cmd
6. Try to read HID descriptor
Notice how there is an usleep_range(1000, 5000) after the first power-on
command, but not after the second power-on command.
Testing has shown that at least on the BMAX Y13 laptop's i2c-hid touchpad,
not having a delay after the second power-on command causes the HID
descriptor to read as all zeros.
In case we hit this on other devices too, the descriptor being all zeros
can be recognized by the following message being logged many, many times:
hid-generic 0018:0911:5288.0002: unknown main item tag 0x0
At the same time as the BMAX Y13's touchpad issue was debugged,
Kai-Heng was working on debugging some issues with Goodix i2c-hid
touchpads. It turns out that these need a delay after a PWR_ON command
too, otherwise they stop working after a suspend/resume cycle.
According to Goodix a delay of minimal 60ms is needed.
Having multiple cases where we need a delay after sending the power-on
command, seems to indicate that we should always sleep after the power-on
command.
This commit fixes the mentioned issues by moving the existing 1ms sleep to
the i2c_hid_set_power() function and changing it to a 60ms sleep.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208247 Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reported-and-tested-by: Andrea Borgia <andrea@borgia.bo.it> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of block device backend, if the backend supports write zeros, the
loop device will set queue flag of QUEUE_FLAG_DISCARD. However,
limits.discard_granularity isn't setup, and this way is wrong,
see the following description in Documentation/ABI/testing/sysfs-block:
A discard_granularity of 0 means that the device does not support
discard functionality.
Especially 9b15d109a6b2 ("block: improve discard bio alignment in
__blkdev_issue_discard()") starts to take q->limits.discard_granularity
for computing max discard sectors. And zero discard granularity may cause
kernel oops, or fail discard request even though the loop queue claims
discard support via QUEUE_FLAG_DISCARD.
Fix the issue by setup discard granularity and alignment.
Fixes: c52abf563049 ("loop: Better discard support for block devices") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Coly Li <colyli@suse.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Xiao Ni <xni@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Evan Green <evgreen@chromium.org> Cc: Gwendal Grignou <gwendal@chromium.org> Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Performance monitor interrupt handler checks if any counter has
overflown and calls record_and_restart() in core-book3s which invokes
perf_event_overflow() to record the sample information. Apart from
creating sample, perf_event_overflow() also does the interrupt and
period checks via perf_event_account_interrupt().
Currently we record information only if the SIAR (Sampled Instruction
Address Register) valid bit is set (using siar_valid() check) and
hence the interrupt check.
But it is possible that we do sampling for some events that are not
generating valid SIAR, and hence there is no chance to disable the
event if interrupts are more than max_samples_per_tick. This leads to
soft lockup.
Fix this by adding perf_event_account_interrupt() in the invalid SIAR
code path for a sampling event. ie if SIAR is invalid, just do
interrupt check and don't record the sample information.
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.
iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:
# ip link add link eth0 name macvlan0 type macvlan mode source
# ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
RTNETLINK answers: Cannot assign requested address
# ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
# ip -d link show macvlan0
5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...
With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
FCoE adapter initialization failed for ISP8021 with the following patch
applied. In addition, reproduction of the issue the patch originally tried
to address has been unsuccessful.
NVMEAsync command is being submitted to QLA while the same NVMe controller
is in the middle of reset. The reset path has deleted the association and
freed aen_op->fcp_req.private. Add a check for this private pointer before
issuing the command.
OS boot during Boot from SAN was stuck at dracut emergency shell after
enabling NVMe driver parameter. For non-MQ support the driver was enabling
MQ. Add a check to confirm if FW supports MQ.
If somehow no interrupt notification is raised for a completed request and
its doorbell bit is cleared by host, UFS driver needs to cleanup its
outstanding bit in ufshcd_abort(). Otherwise, system may behave abnormally
in the following scenario:
After ufshcd_abort() returns, this request will be requeued by SCSI layer
with its outstanding bit set. Any future completed request will trigger
ufshcd_transfer_req_compl() to handle all "completed outstanding bits". At
this time the "abnormal outstanding bit" will be detected and the "requeued
request" will be chosen to execute request post-processing flow. This is
wrong because this request is still "alive".
Link: https://lore.kernel.org/r/20200811141859.27399-2-huobean@gmail.com Reviewed-by: Can Guo <cang@codeaurora.org> Acked-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ufshcd_suspend(), after clk-gating is suspended and link is set
as Hibern8 state, ufshcd_hold() is still possibly invoked before
ufshcd_suspend() returns. For example, MediaTek's suspend vops may
issue UIC commands which would call ufshcd_hold() during the command
issuing flow.
Now if UFSHCD_CAP_HIBERN8_WITH_CLK_GATING capability is enabled,
then ufshcd_hold() may enter infinite loops because there is no
clk-ungating work scheduled or pending. In this case, ufshcd_hold()
shall just bypass, and keep the link as Hibern8 state.
Link: https://lore.kernel.org/r/20200809050734.18740-1-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Co-developed-by: Andy Teng <andy.teng@mediatek.com> Signed-off-by: Andy Teng <andy.teng@mediatek.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ixgbe_fcoe_ddp_setup() can be called from the main I/O path and is called
with a spin_lock held, so we have to use GFP_ATOMIC allocation instead of
GFP_KERNEL.
The driver supports WM1811, WM8994, WM8958 devices but according to
documentation and the regmap definitions the WM8958_DSP2_* registers
are only available on WM8958. In current code these registers are
being accessed as if they were available on all the three chips.
When starting playback on WM1811 CODEC multiple errors like:
"wm8994-codec wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5"
can be seen, which is caused by attempts to read an unavailable
WM8958_DSP2_PROGRAM register. The issue has been uncovered by recent
commit "e2329ee ASoC: soc-component: add soc_component_err()".
This patch adds a check in wm8958_aif_ev() callback so the DSP2 handling
is only done for WM8958.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200731173834.23832-1-s.nawrocki@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
If a device is hot-removed --- for example, when a physical device is
unplugged from pcie slot or a nbd device's network is shutdown ---
this can result in a BUG_ON() crash in submit_bh_wbc(). This is
because the when the block device dies, the buffer heads will have
their Buffer_Mapped flag get cleared, leading to the crash in
submit_bh_wbc.
We had attempted to work around this problem in commit a17712c8
("ext4: check superblock mapped prior to committing"). Unfortunately,
it's still possible to hit the BUG_ON(!buffer_mapped(bh)) if the
device dies between when the work-around check in ext4_commit_super()
and when submit_bh_wbh() is finally called:
Code path:
ext4_commit_super
judge if 'buffer_mapped(sbh)' is false, return <== commit a17712c8
lock_buffer(sbh)
...
unlock_buffer(sbh)
__sync_dirty_buffer(sbh,...
lock_buffer(sbh)
judge if 'buffer_mapped(sbh))' is false, return <== added by this patch
submit_bh(...,sbh)
submit_bh_wbc(...,sbh,...)
When remounting filesystem fails late during remount handling and
block_validity mount option is also changed during the remount, we fail
to restore system zone information to a state matching the mount option.
This is mostly harmless, just the block validity checking will not match
the situation described by the mount option. Make sure these two are always
consistent.
Fix it by applying the SB_LAZYTIME and SB_I_VERSION flags from *flags to
s_flags before we parse the option and use the resulting state of the
same flags in *flags at the end of successful remount.
If we free a metadata buffer which has been failed to async write out
in the background, the jbd2 checkpoint procedure will not detect this
failure in jbd2_log_do_checkpoint(), so it may lead to filesystem
inconsistency after cleanup journal tail. This patch abort the journal
if free a buffer has write_io_error flag to prevent potential further
inconsistency.
Ext4 uses blkdev_get_by_dev() to get the block_device for journal device
which does check to see if the read-only block device was opened
read-only.
As a result ext4 will hapily proceed mounting the file system with
external journal on read-only device. This is bad as we would not be
able to use the journal leading to errors later on.
Instead of simply failing to mount file system in this case, treat it in
a similar way we treat internal journal on read-only device. Allow to
mount with -o noload in read-only mode.
A customer has reported a BUG_ON in ext4_clear_journal_err() hitting
during an LTP testing. Either this has been caused by a test setup
issue where the filesystem was being overwritten while LTP was mounting
it or the journal replay has overwritten the superblock with invalid
data. In either case it is preferable we don't take the machine down
with a BUG_ON. So handle the situation of unexpectedly missing
has_journal feature more gracefully. We issue warning and fail the mount
in the cases where the race window is narrow and the failed check is
most likely a programming error. In cases where fs corruption is more
likely, we do full ext4_error() handling before failing mount / remount.
Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200710140759.18031-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Callers of __jbd2_journal_unfile_buffer() and
__jbd2_journal_refile_buffer() assume that the b_transaction is set. In
fact if it's not, we can end up with journal_head refcounting errors
leading to crash much later that might be very hard to track down. Add
asserts to make sure that is the case.
We also make sure that b_next_transaction is NULL in
__jbd2_journal_unfile_buffer() since the callers expect that as well and
we should not get into that stage in this state anyway, leading to
problems later on if we do.
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log