Bjorn Andersson [Mon, 18 May 2020 18:44:57 +0000 (11:44 -0700)]
arm64: dts: qcom: sc7180: Fix ETMv4 power management patch
The lack of unique context in '0f1decaa83b7 ("arm64: dts: qcom: sc7180:
Support ETMv4 power management")' caused the patch to be applied
off-by-one. Move the "arm,coresight-loses-context-with-cpu" properties
down one node, so that it applies to the ETMs and not the replicator.
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
arm64: dts: qcom: msm8996: Make GPU node control GPU_GX GDSC
Presumably the GPU node needs to control both the GPU and GPU GX power
domains, but given that GPU GX now depends on the GPU GDSC both can
effectively be controlled by controlling GPU GX. So use this instead.
arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc
Add the SPMI regulator node in the PMI8994, use it to give us VDD_GX
at a fixed max nominal voltage for the db820c and specify this as supply
for the MMSS GPU_GX GDSC.
With the introduction of CPR support the range for VDD_GX should be
expanded.
Stephan Gerhold [Thu, 14 May 2020 11:27:54 +0000 (13:27 +0200)]
arm64: dts: qcom: apq8016-sbc: merge -pins.dtsi into main .dtsi
apq8016-sbc.dtsi is the only remaining device which takes up
4 files since it has its pinctrl split into separate files.
Actually this does not really make the device tree easier to read
(just harder to find nodes). For db820c the files were merged in
commit 88264f1f6bf5 ("arm64: dts: qcom: db820c: Remove pin specific files").
Do the same for apq8016-sbc (db410c) and move the pinctrl definitions
into apq8016-sbc.dtsi.
Stephan Gerhold [Thu, 14 May 2020 11:27:53 +0000 (13:27 +0200)]
arm64: dts: qcom: msm8916: move gpu opp table to gpu node
In msm8916.dtsi the GPU OPP table is defined under the root node,
whereas in msm8996.dtsi/sdm845.dtsi it is a subnode of the gpu device
(which makes it easier to find).
Move it to the gpu device node to make this consistent.
Stephan Gerhold [Thu, 14 May 2020 11:27:52 +0000 (13:27 +0200)]
arm64: dts: qcom: msm8916: avoid using _ in node names
Many nodes in the MSM8916 device trees use '_' in node names
(especially pinctrl), even though (seemingly) '-' is preferred now.
Make this more consistent by replacing '_' with '-' where possible.
Similar naming is used for pinctrl in newer device trees (e.g. sdm845.dtsi).
It's uncertain where the "vreg_s8a_l3a_input" comes from, but the supply
for VDD_L3_L11 on PM8994 should be VREG_S3A_1P3, so correct this - and
drop the vreg_s8a_l3a_input.
The PMI8994 provides 3 SPMS regulators and one boost/bypass regulator.
Define s1 and the boot/bypass and update pm8994 to appropriately
describe the supply from PMI8994.
Michael Srba [Wed, 13 May 2020 18:47:35 +0000 (20:47 +0200)]
arm64: dts: qcom: msm8916: Disable coresight by default
On some msm8916 devices, attempts at initializing coresight cause the boot to
fail. This was fixed by disabling the coresight-related nodes in the board dts
files. However, a cleaner approach was chosen for fixing the same issue on
msm8998: disabling coresight by default, and enabling it in board dts files
where desired.
This patch implements the same solution for msm8916, removes now redundant
overwrites in board specific dts files and and enables coresight in db410c's
board dts in order to keep the current behavior.
Fixes: b1fcc5702a41 ("arm64: dts: qcom: msm8916: Add CTI options") Signed-off-by: Michael Srba <michael.srba@seznam.cz> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lore.kernel.org/r/20200513184735.30104-1-michael.srba@seznam.cz Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
arm64: dts: qcom: sc7180: Support ETMv4 power management
Now that deep idle states are properly supported on SC7180,
we need to add "coresight-loses-context-with-cpu" property
to avoid failure of trace session because of losing context
on entering deep idle states.
Douglas Anderson [Thu, 7 May 2020 21:35:00 +0000 (14:35 -0700)]
arm64: dts: sdm845: Add "no-hpd" to sn65dsi86 on cheza
We don't have the HPD line hooked up to the bridge chip. Add it as
suggested in the patch ("dt-bindings: drm/bridge: ti-sn65dsi86:
Document no-hpd").
NOTE: this patch isn't expected to have any effect but just keeps us
cleaner for the future. Currently the driver in Linux just assumes
that nobody has HPD hooked up. This change allows us to later
implement HPD support in the driver without messing up sdm845-cheza.
Alex Elder [Mon, 4 May 2020 18:13:50 +0000 (13:13 -0500)]
arm64: dts: sdm845: add IPA iommus property
Add an "iommus" property to the IPA node in "sdm845.dtsi". It is
required because there are two regions of memory the IPA accesses
through an SMMU. The next few patches define and map those regions.
Mike Leach [Wed, 15 Apr 2020 20:12:30 +0000 (21:12 +0100)]
arm64: dts: qcom: msm8916: Add CTI options
Adds system and CPU bound CTI definitions for Qualcom msm8916 platform
(Dragonboard DB410C).
System CTIs 2-11 are omitted as no information available at present.
Signed-off-by: Mike Leach <mike.leach@linaro.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20200415201230.15766-1-mike.leach@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds the initial device tree support for Xiaomi
Redmi Note 7 (codename lavender) phone. It is based on
SDM660 SoC. Currently it can be booted into initrd with
a shell over UART and you can also get kernel boot logs
from a pstore-ramoops.
Amit Kucheria [Mon, 30 Mar 2020 10:06:28 +0000 (15:36 +0530)]
arm64: dts: qcom: msm8998: remove unit name for thermal trip points
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Amit Kucheria [Mon, 30 Mar 2020 10:06:27 +0000 (15:36 +0530)]
arm64: dts: qcom: msm8996: remove unit name for thermal trip points
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Amit Kucheria [Mon, 30 Mar 2020 10:06:26 +0000 (15:36 +0530)]
arm64: dts: qcom: msm8916: remove unit name for thermal trip points
The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Krishna Manikandan [Fri, 20 Mar 2020 13:11:04 +0000 (18:41 +0530)]
arm64: dts: qcom: sc7180: modify assigned clocks for sc7180 target
Add DISP_CC_MDSS_ROT_CLK and DISP_CC_MDSS_AHB_CLK
in the assigned clocks list as these are display
specific clocks and needs to be initialized from
the client side. Adding the default rate of
19.2 mhz for these clocks for sc7180 target.
Evan Green [Tue, 10 Mar 2020 23:16:29 +0000 (16:16 -0700)]
arm64: dts: qcom: sc7180: Include interconnect definitions
Re-introduce the include of the sc7180 interconnect node name
definitions. Though this was part of v5 of the interconnect provider
series [1], it was dropped because the DT changes went through a
different tree than the header. Re-add that now.
Interconnect clients being introduced can reference this patch as a
dependency, rather than racing each other to add the include.
Robert Foss [Tue, 24 Mar 2020 15:58:41 +0000 (16:58 +0100)]
arm64: dts: qcom: sdm845-db845c: Add ov8856 & ov7251 camera nodes
Enable the ov8856 main camera and the ov7251 b/w tracking camera
used on the Qualcomm RB3 kit.
Currently the camera nodes have not yet been attached to an to a
CSI2 endpoint, since no driver currently supports the ISP that the the
SDM845/db845c ships with.
Bjorn Andersson [Wed, 11 Mar 2020 19:15:12 +0000 (19:15 +0000)]
arm64: dts: qcom: qcs404: Add USB devices and PHYs
QCS404 sports HS and SS USB controllers based on dwc3 block with two HS
PHYs and one SS PHY. Add nodes for these devices and enable them for
EVB board.
Ulf Hansson [Thu, 26 Mar 2020 10:39:31 +0000 (11:39 +0100)]
arm64: dts: qcom: msm8916: Conform to the domain-idle-state binding
As the domain-idle-state DT binding got converted to the json-schema, a few
minor changes were introduced. For example, the states needs to be
specified within a separate node, named domain-idle-states. Let's conform
to the updated binding.
This also silence the below errors for msm8916 from of 'make dtbs_check':
idle-states: cluster-retention:compatible:0: 'arm,idle-state' was expected
idle-states: cluster-gdhs:compatible:0: 'arm,idle-state' was expected
This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file. But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.
They are all supposed to be sorted, but people who add new entries don't
always know the alphabet. Plus sometimes the entry names get edited,
and people don't then re-order the entry.
Let's see how painful this will be for merging purposes (the MAINTAINERS
file is often edited in various different trees), but Joe claims there's
relatively few patches in -next that touch this, and doing it just
before -rc1 is likely the best time. Fingers crossed.
Merge tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of three patches to fix the fallout of the newly added split
lock detection feature.
It addressed the case where a KVM guest triggers a split lock #AC and
KVM reinjects it into the guest which is not prepared to handle it.
Add proper sanity checks which prevent the unconditional injection
into the guest and handles the #AC on the host side in the same way as
user space detections are handled. Depending on the detection mode it
either warns and disables detection for the task or kills the task if
the mode is set to fatal"
* tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
KVM: x86: Emulate split-lock access as a write in emulator
x86/split_lock: Provide handle_guest_split_lock()
Merge tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull time(keeping) updates from Thomas Gleixner:
- Fix the time_for_children symlink in /proc/$PID/ so it properly
reflects that it part of the 'time' namespace
- Add the missing userns limit for the allowed number of time
namespaces, which was half defined but the actual array member was
not added. This went unnoticed as the array has an exessive empty
member at the end but introduced a user visible regression as the
output was corrupted.
- Prevent further silent ucount corruption by adding a BUILD_BUG_ON()
to catch half updated data.
* tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ucount: Make sure ucounts in /proc/sys/user don't regress again
time/namespace: Add max_time_namespaces ucount
time/namespace: Fix time_for_children symlink
Merge tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes/updates from Thomas Gleixner:
- Deduplicate the average computations in the scheduler core and the
fair class code.
- Fix a raise between runtime distribution and assignement which can
cause exceeding the quota by up to 70%.
- Prevent negative results in the imbalanace calculation
- Remove a stale warning in the workqueue code which can be triggered
since the call site was moved out of preempt disabled code. It's a
false positive.
- Deduplicate the print macros for procfs
- Add the ucmap values to the SCHED_DEBUG procfs output for completness
* tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Add task uclamp values to SCHED_DEBUG procfs
sched/debug: Factor out printing formats into common macros
sched/debug: Remove redundant macro define
sched/core: Remove unused rq::last_load_update_tick
workqueue: Remove the warning in wq_worker_sleeping()
sched/fair: Fix negative imbalance in imbalance calculation
sched/fair: Fix race between runtime distribution and assignment
sched/fair: Align rq->avg_idle and rq->avg_scan_cost
Merge tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Three fixes/updates for perf:
- Fix the perf event cgroup tracking which tries to track the cgroup
even for disabled events.
- Add Ice Lake server support for uncore events
- Disable pagefaults when retrieving the physical address in the
sampling code"
* tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Disable page faults when getting phys address
perf/x86/intel/uncore: Add Ice Lake server uncore support
perf/cgroup: Correct indirection in perf_less_group_idx()
perf/core: Fix event cgroup tracking
Merge tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Ten cifs/smb fixes:
- five RDMA (smbdirect) related fixes
- add experimental support for swap over SMB3 mounts
- also a fix which improves performance of signed connections"
* tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: enable swap on SMB3 mounts
smb3: change noisy error message to FYI
smb3: smbdirect support can be configured by default
cifs: smbd: Do not schedule work to send immediate packet on every receive
cifs: smbd: Properly process errors on ib_post_send
cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets
cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending
cifs: smbd: Check send queue size before posting a send
cifs: smbd: Merge code to track pending packets
cifs: ignore cached share root handle closing errors
Merge tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- fix an integer truncation in dma_direct_get_required_mask
(Kishon Vijay Abraham)
- fix the display of dma mapping types (Grygorii Strashko)
* tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix displaying of dma allocation type
dma-direct: fix data truncation in dma_direct_get_required_mask()
Merge tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
Xiaoyao Li [Fri, 10 Apr 2020 11:54:02 +0000 (13:54 +0200)]
KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
Two types of #AC can be generated in Intel CPUs:
1. legacy alignment check #AC
2. split lock #AC
Reflect #AC back into the guest if the guest has legacy alignment checks
enabled or if split lock detection is disabled.
If the #AC is not a legacy one and split lock detection is enabled, then
invoke handle_guest_split_lock() which will either warn and disable split
lock detection for this task or force SIGBUS on it.
[ tglx: Switch it to handle_guest_split_lock() and rename the misnamed
helper function. ]
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Link: https://lkml.kernel.org/r/20200410115517.176308876@linutronix.de
Xiaoyao Li [Fri, 10 Apr 2020 11:54:01 +0000 (13:54 +0200)]
KVM: x86: Emulate split-lock access as a write in emulator
Emulate split-lock accesses as writes if split lock detection is on
to avoid #AC during emulation, which will result in a panic(). This
should never occur for a well-behaved guest, but a malicious guest can
manipulate the TLB to trigger emulation of a locked instruction[1].
Thomas Gleixner [Fri, 10 Apr 2020 11:54:00 +0000 (13:54 +0200)]
x86/split_lock: Provide handle_guest_split_lock()
Without at least minimal handling for split lock detection induced #AC,
VMX will just run into the same problem as the VMWare hypervisor, which
was reported by Kenneth.
It will inject the #AC blindly into the guest whether the guest is
prepared or not.
Provide a function for guest mode which acts depending on the host
SLD mode. If mode == sld_warn, treat it like user space, i.e. emit a
warning, disable SLD and mark the task accordingly. Otherwise force
SIGBUS.
[ bp: Add a !CPU_SUP_INTEL stub for handle_guest_split_lock(). ]
- Almost all of the rest of MM (memcg, slab-generic, slab, pagealloc,
gup, hugetlb, pagemap, memremap)
- Various other things (hfs, ocfs2, kmod, misc, seqfile)
* akpm: (34 commits)
ipc/util.c: sysvipc_find_ipc() should increase position index
kernel/gcov/fs.c: gcov_seq_next() should increase position index
fs/seq_file.c: seq_read(): add info message about buggy .next functions
drivers/dma/tegra20-apb-dma.c: fix platform_get_irq.cocci warnings
change email address for Pali Rohár
selftests: kmod: test disabling module autoloading
selftests: kmod: fix handling test numbers above 9
docs: admin-guide: document the kernel.modprobe sysctl
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
kmod: make request_module() return an error when autoloading is disabled
mm/memremap: set caching mode for PCI P2PDMA memory to WC
mm/memory_hotplug: add pgprot_t to mhp_params
powerpc/mm: thread pgprot_t through create_section_mapping()
x86/mm: introduce __set_memory_prot()
x86/mm: thread pgprot_t through init_memory_mapping()
mm/memory_hotplug: rename mhp_restrictions to mhp_params
mm/memory_hotplug: drop the flags field from struct mhp_restrictions
mm/special: create generic fallbacks for pte_special() and pte_mkspecial()
mm/vma: introduce VM_ACCESS_FLAGS
mm/vma: define a default value for VM_DATA_DEFAULT_FLAGS
...
Merge tag 'for-linus-5.7-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs updates from Mike Marshall:
"A fix and two cleanups.
Fix:
- Christoph Hellwig noticed that some logic I added to
orangefs_file_read_iter introduced a race condition, so he sent a
reversion patch. I had to modify his patch since reverting at this
point broke Orangefs.
Cleanups:
- Christoph Hellwig noticed that we were doing some unnecessary work
in orangefs_flush, so he sent in a patch that removed the un-needed
code.
- Al Viro told me he had trouble building Orangefs. Orangefs should
be easy to build, even for Al :-).
I looked back at the test server build notes in orangefs.txt, just
in case that's where the trouble really is, and found a couple of
typos and made a couple of clarifications"
* tag 'for-linus-5.7-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: clarify build steps for test server in orangefs.txt
orangefs: don't mess with I_DIRTY_TIMES in orangefs_flush
orangefs: get rid of knob code...
Merge tag 'xtensa-20200410' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtensa updates from Max Filippov:
- replace setup_irq() by request_irq()
- cosmetic fixes in xtensa Kconfig and boot/Makefile
* tag 'xtensa-20200410' of git://github.com/jcmvbkbc/linux-xtensa:
arch/xtensa: fix grammar in Kconfig help text
xtensa: remove meaningless export ccflags-y
xtensa: replace setup_irq() by request_irq()
Merge tag 'for-linus-5.7-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- two cleanups
- fix a boot regression introduced in this merge window
- fix wrong use of memory allocation flags
* tag 'for-linus-5.7-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: fix booting 32-bit pv guest
x86/xen: make xen_pvmmu_arch_setup() static
xen/blkfront: fix memory allocation flags in blkfront_setup_indirect()
xen: Use evtchn_type_t as a type for event channels
fs/seq_file.c: seq_read(): add info message about buggy .next functions
Patch series "seq_file .next functions should increase position index".
In Aug 2018 NeilBrown noticed commit 1f4aace60b0e ("fs/seq_file.c:
simplify seq_file iteration code and interface")
"Some ->next functions do not increment *pos when they return NULL...
Note that such ->next functions are buggy and should be fixed. A simple
demonstration is dd if=/proc/swaps bs=1000 skip=1 Choose any block size
larger than the size of /proc/swaps. This will always show the whole
last line of /proc/swaps"
Described problem is still actual. If you make lseek into middle of
last output line following read will output end of last line and whole
last line once again.
$ dd if=/proc/swaps bs=1 # usual output
Filename Type Size Used Priority
/dev/dm-0 partition 4194812 97536 -2
104+0 records in
104+0 records out
104 bytes copied
$ dd if=/proc/swaps bs=40 skip=1 # last line was generated twice
dd: /proc/swaps: cannot skip to specified offset
v/dm-0 partition 4194812 97536 -2
/dev/dm-0 partition 4194812 97536 -2
3+1 records in
3+1 records out
131 bytes copied
There are lot of other affected files, I've found 30+ including
/proc/net/ip_tables_matches and /proc/sysvipc/*
I've sent patches into maillists of affected subsystems already, this
patch-set fixes the problem in files related to pstore, tracing, gcov,
sysvipc and other subsystems processed via linux-kernel@ mailing list
directly
Eric Biggers [Fri, 10 Apr 2020 21:33:53 +0000 (14:33 -0700)]
selftests: kmod: fix handling test numbers above 9
get_test_count() and get_test_enabled() were broken for test numbers
above 9 due to awk interpreting a field specification like '$0010' as
octal rather than decimal. Fix it by stripping the leading zeroes.
Eric Biggers [Fri, 10 Apr 2020 21:33:50 +0000 (14:33 -0700)]
docs: admin-guide: document the kernel.modprobe sysctl
Document the kernel.modprobe sysctl in the same place that all the other
kernel.* sysctls are documented. Make sure to mention how to use this
sysctl to completely disable module autoloading, and how this sysctl
relates to CONFIG_STATIC_USERMODEHELPER.
Eric Biggers [Fri, 10 Apr 2020 21:33:47 +0000 (14:33 -0700)]
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
After request_module(), nothing is stopping the module from being
unloaded until someone takes a reference to it via try_get_module().
The WARN_ONCE() in get_fs_type() is thus user-reachable, via userspace
running 'rmmod' concurrently.
Since WARN_ONCE() is for kernel bugs only, not for user-reachable
situations, downgrade this warning to pr_warn_once().
Keep it printed once only, since the intent of this warning is to detect
a bug in modprobe at boot time. Printing the warning more than once
wouldn't really provide any useful extra information.
Fixes: 41124db869b7 ("fs: warn in case userspace lied about modprobe return") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Jessica Yu <jeyu@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jeff Vander Stoep <jeffv@google.com> Cc: Jessica Yu <jeyu@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: NeilBrown <neilb@suse.com> Cc: <stable@vger.kernel.org> [4.13+] Link: http://lkml.kernel.org/r/20200312202552.241885-3-ebiggers@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / users / jedix / linux-maple.git / log