The fix is to drop of_match_ptr() which is not necessary because DT is
always used for this driver (well, it could in theory support ACPI only,
but CONFIG_OF is always enabled for arm64).
Fixes: a243ecc323b9 ("net: mdio: xgene: Use device_get_match_data()") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202310170832.xnVXw1bb-lkp@intel.com/ Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20231019182345.833136-1-robh@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sabrina Dubroca [Fri, 20 Oct 2023 14:00:55 +0000 (16:00 +0200)]
tls: don't reset prot->aad_size and prot->tail_size for TLS_HW
Prior to commit 1a074f7618e8 ("tls: also use init_prot_info in
tls_set_device_offload"), setting TLS_HW on TX didn't touch
prot->aad_size and prot->tail_size. They are set to 0 during context
allocation (tls_prot_info is embedded in tls_context, kzalloc'd by
tls_ctx_create).
When the RX key is configured, tls_set_sw_offload is called (for both
TLS_SW and TLS_HW). If the TX key is configured in TLS_HW mode after
the RX key has been installed, init_prot_info will now overwrite the
correct values of aad_size and tail_size, breaking SW decryption and
causing -EBADMSG errors to be returned to userspace.
Since TLS_HW doesn't use aad_size and tail_size at all (for TLS1.2,
tail_size is always 0, and aad_size is equal to TLS_HEADER_SIZE +
rec_seq_size), we can simply drop this hunk.
Eric Dumazet [Fri, 20 Oct 2023 12:57:47 +0000 (12:57 +0000)]
tcp: add support for usec resolution in TCP TS values
Back in 2015, Van Jacobson suggested to use usec resolution in TCP TS values.
This has been implemented in our private kernels.
Goals were :
1) better observability of delays in networking stacks.
2) better disambiguation of events based on TSval/ecr values.
3) building block for congestion control modules needing usec resolution.
Back then we implemented a schem based on private SYN options
to negotiate the feature.
For upstream submission, we chose to use a route attribute,
because this feature is probably going to be used in private
networks [1] [2].
ip route add 10/8 ... features tcp_usec_ts
Note that RFC 7323 recommends a
"timestamp clock frequency in the range 1 ms to 1 sec per tick.",
but also mentions
"the maximum acceptable clock frequency is one tick every 59 ns."
[1] Unfortunately RFC 7323 5.5 (Outdated Timestamps) suggests
to invalidate TS.Recent values after a flow was idle for more
than 24 days. This is the part making usec_ts a problem
for peers following this recommendation for long living
idle flows.
Eric Dumazet [Fri, 20 Oct 2023 12:57:40 +0000 (12:57 +0000)]
tcp: replace tcp_time_stamp_raw()
In preparation of usec TCP TS support, remove tcp_time_stamp_raw()
in favor of tcp_clock_ts() helper. This helper will return a suitable
32bit result to feed TS values, depending on a socket field.
Also add tcp_tw_tsval() and tcp_rsk_tsval() helpers to factorize
the details.
We do not yet support usec timestamps.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 20 Oct 2023 12:57:37 +0000 (12:57 +0000)]
tcp: fix cookie_init_timestamp() overflows
cookie_init_timestamp() is supposed to return a 64bit timestamp
suitable for both TSval determination and setting of skb->tstamp.
Unfortunately it uses 32bit fields and overflows after
2^32 * 10^6 nsec (~49 days) of uptime.
Generated TSval are still correct, but skb->tstamp might be set
far away in the past, potentially confusing other layers.
tcp_ns_to_ts() is changed to return a full 64bit value,
ts and ts_now variables are changed to u64 type,
and TSMASK is removed in favor of shifts operations.
While we are at it, change this sequence:
ts >>= TSBITS;
ts--;
ts <<= TSBITS;
ts |= options;
to:
ts -= (1UL << TSBITS);
Fixes: 9a568de4818d ("tcp: switch TCP TS option (RFC 7323) to 1ms clock") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Fri, 20 Oct 2023 11:55:29 +0000 (13:55 +0200)]
vxlan: use generic function for tunnel IPv6 route lookup
The route lookup can be done now via generic function
udp_tunnel6_dst_lookup() to replace the custom implementation in
vxlan6_get_route().
This is similar to what already done for IPv4 in commit 6f19b2c136d9
("vxlan: use generic function for tunnel IPv4 route lookup").
Suggested-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Fri, 20 Oct 2023 11:55:28 +0000 (13:55 +0200)]
geneve: use generic function for tunnel IPv6 route lookup
The route lookup can be done now via generic function
udp_tunnel6_dst_lookup() to replace the custom implementation in
geneve_get_v6_dst().
This is similar to what already done for IPv4 in commit daa2ba7ed1d1
("geneve: use generic function for tunnel IPv4 route lookup").
Suggested-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Fri, 20 Oct 2023 11:55:27 +0000 (13:55 +0200)]
ipv6: add new arguments to udp_tunnel6_dst_lookup()
We want to make the function more generic so that it can be used by
other UDP tunnel implementations such as geneve and vxlan. To do that,
add the following arguments:
- source and destination UDP port;
- ifindex of the output interface, needed by vxlan;
- the tos, because in some cases it is not taken from struct
ip_tunnel_info (for example, when it's inherited from the inner
packet);
- the dst cache, because not all tunnel types (e.g. vxlan) want to
use the one from struct ip_tunnel_info.
With these parameters, the function no longer needs the full struct
ip_tunnel_info as argument and we can pass only the relevant part of
it (struct ip_tunnel_key).
This is similar to what already done for IPv4 in commit 72fc68c6356b
("ipv4: add new arguments to udp_tunnel_dst_lookup()").
Suggested-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Fri, 20 Oct 2023 11:55:26 +0000 (13:55 +0200)]
ipv6: remove "proto" argument from udp_tunnel6_dst_lookup()
The function is now UDP-specific, the protocol is always IPPROTO_UDP.
This is similar to what already done for IPv4 in commit 78f3655adcb5
("ipv4: remove "proto" argument from udp_tunnel_dst_lookup()").
Suggested-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino Galvani [Fri, 20 Oct 2023 11:55:25 +0000 (13:55 +0200)]
ipv6: rename and move ip6_dst_lookup_tunnel()
At the moment ip6_dst_lookup_tunnel() is used only by bareudp.
Ideally, other UDP tunnel implementations should use it, but to do so
the function needs to accept new parameters that are specific for UDP
tunnels, such as the ports.
Prepare for these changes by renaming the function to
udp_tunnel6_dst_lookup() and move it to file
net/ipv6/ip6_udp_tunnel.c.
This is similar to what already done for IPv4 in commit bf3fcbf7e7a0
("ipv4: rename and move ip_route_output_tunnel()").
Suggested-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Gavrilov Ilia [Fri, 20 Oct 2023 12:21:16 +0000 (12:21 +0000)]
net: atm: Remove redundant check.
Checking the 'adev' variable is unnecessary,
because 'cdev' has already been checked earlier.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: 656d98b09d57 ("[ATM]: basic sysfs support for ATM devices") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 22 Oct 2023 10:41:46 +0000 (11:41 +0100)]
Merge branch 'bnxt_en-next'
Michael Chan says:
====================
bnxt_en: Update for net-next
The first 2 patches are fixes for the recently added hwmon changes.
The next 6 patches are enhancements to support ethtool lanes and
all the proper supported and advertised link modes. Before these
patches, the driver was only supporting the link modes for copper
media.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Fri, 20 Oct 2023 21:27:57 +0000 (14:27 -0700)]
bnxt_en: extend media types to supported and autoneg modes
The current driver code does not accurately report the supported and
advertised link modes. It basically always assumes the media type
is copper for any particular speed. Utilize the recently added link
mode mappings to accurately report fully qualified ethtool link modes for
advertised and supported speeds.
If the media type is known, we will report the supported link modes for
that media only. If the media is not known, we will report all possible
supported link modes. The user can now specify any supported link modes
(including NRZ and PAM4) to advertise for autoneg. It used to only accept
copper NRZ modes.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Fri, 20 Oct 2023 21:27:56 +0000 (14:27 -0700)]
bnxt_en: convert to linkmode_set_bit() API
Barring the BNXT_FW_TO_ETHTOOL speed macros, which will be removed
in the next patch, update code to use the newer API.
No functional change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 20 Oct 2023 21:27:55 +0000 (14:27 -0700)]
bnxt_en: Refactor NRZ/PAM4 link speed related logic
Refactor some NRZ/PAM4 link speed related logic into helper functions.
The NRZ and PAM4 link parameters are stored in separate structure fields.
The driver logic has to check whether it is in NRZ or PAM4 mode and
then use the appropriate field.
Refactor this logic into helper functions for better readability.
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com> Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Fri, 20 Oct 2023 21:27:54 +0000 (14:27 -0700)]
bnxt_en: refactor speed independent ethtool modes
A future patch in this series will change the algorithm used to
determine ethtool speed and media modes. Extract the handling of
the unrelated pause, autoneg modes into an independent function.
Also separate FEC handling out of bnxt_fw_to_ethtool_*_spds().
No functional change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Fri, 20 Oct 2023 21:27:53 +0000 (14:27 -0700)]
bnxt_en: support lane configuration via ethtool
Recent kernels support changing the number of link lanes via ethtool.
This is useful for determining the appropriate signal mode to use when
a given link speed can be achieved using different lane configurations.
Accept the ethtool lanes parameter when configuring forced speed. If
there is no lanes parameter, select a default.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edwin Peer [Fri, 20 Oct 2023 21:27:52 +0000 (14:27 -0700)]
bnxt_en: add infrastructure to lookup ethtool link mode
Add infrastructure to look up the enum ethtool_link_mode_bit_indices
from link information provided by the firmware. The link speed,
signal mode, and media type returned by firmware will be used to
look up the ethtool link mode.
The immediate benefit is that once the link mode is determined, we can
now use ethtool_params_from_link_mode() to fill the basic ethtool
parameters including the number of lanes. Lanes will be fully
supported in the next patch.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Fri, 20 Oct 2023 21:27:51 +0000 (14:27 -0700)]
bnxt_en: Fix invoking hwmon_notify_event
FW sends the async event to the driver when the device temperature goes
above or below the threshold values. Only notify hwmon if the
temperature is increasing to the next alert level, not when it is
decreasing.
Cc: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalesh AP [Fri, 20 Oct 2023 21:27:50 +0000 (14:27 -0700)]
bnxt_en: Do not call sleeping hwmon_notify_event() from NAPI
Defer hwmon_notify_event() to bnxt_sp_task() workqueue because
hwmon_notify_event() can try to acquire a mutex shown in the stack trace
below. Modify bnxt_event_error_report() to return true if we need to
schedule bnxt_sp_task() to notify hwmon.
Cc: Guenter Roeck <linux@roeck-us.net> Fixes: a19b4801457b ("bnxt_en: Event handler for Thermal event") Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Stitt [Thu, 19 Oct 2023 18:21:22 +0000 (18:21 +0000)]
net: wwan: replace deprecated strncpy with strscpy
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect chinfo.name to be NUL-terminated based on its use with format
strings and sprintf:
rpmsg/rpmsg_char.c
165: dev_err(dev, "failed to open %s\n", eptdev->chinfo.name);
368: return sprintf(buf, "%s\n", eptdev->chinfo.name);
... we know other members are zero-initialized. This means no
NUL-padding is required (as any NUL-byte assignments are redundant).
Considering the above, a suitable replacement is `strscpy` due to the
fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
David S. Miller [Fri, 20 Oct 2023 11:53:06 +0000 (12:53 +0100)]
Merge branch 'ice-vf-resource-tracking'
Jacob Keller says:
====================
Intel Wired LAN Driver Updates 2023-10-19 (ice, igb, ixgbe)
This series contains improvements to the ice driver related to VF MSI-X
resource tracking, as well as other minor cleanups.
Dan fixes code in igb and ixgbe where the conversion to list_for_each_entry
failed to account for logic which assumed a NULL pointer after iteration.
Jacob makes ice_get_pf_c827_idx static, and refactors ice_find_netlist_node
based on feedback that got missed before the function merged.
Michal adds a switch rule to drop all traffic received by an inactive LAG
port. He also implements ops to allow individual control of MSI-X vectors
for SR-IOV VFs.
Przemek removes some unused fields in struct ice_flow_entry, and modifies
the ice driver to cache the VF PCI device inside struct ice_vf rather than
performing lookup at run time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 19 Oct 2023 17:32:27 +0000 (10:32 -0700)]
ixgbe: fix end of loop test in ixgbe_set_vf_macvlan()
The list iterator in a list_for_each_entry() loop can never be NULL.
If the loop exits without hitting a break then the iterator points
to an offset off the list head and dereferencing it is an out of
bounds access.
Before we transitioned to using list_for_each_entry() loops, then
it was possible for "entry" to be NULL and the comments mention
this. I have updated the comments to match the new code.
Fixes: c1fec890458a ("ethernet/intel: Use list_for_each_entry() helper") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 19 Oct 2023 17:32:26 +0000 (10:32 -0700)]
igb: Fix an end of loop test
When we exit a list_for_each_entry() without hitting a break statement,
the list iterator isn't NULL, it just point to an offset off the
list_head. In that situation, it wouldn't be too surprising for
entry->free to be true and we end up corrupting memory.
The way to test for these is to just set a flag.
Fixes: c1fec890458a ("ethernet/intel: Use list_for_each_entry() helper") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 19 Oct 2023 17:32:25 +0000 (10:32 -0700)]
ice: cleanup ice_find_netlist_node
The ice_find_netlist_node function was introduced in commit 8a3a565ff210
("ice: add admin commands to access cgu configuration"). Variations of this
function were reviewed concurrently on both intel-wired-lan[1][2], and
netdev [3][4]
The variant I posted had a few changes due to review feedback which were
never incorporated into the DPLL series:
* Replace the references to ancient and long removed ICE_SUCCESS and
ICE_ERR_DOES_NOT_EXIST status codes in the function comment.
* Return -ENOENT instead of -ENOTBLK, as a more common way to indicate that
an entry doesn't exist.
* Avoid the use of memset() and use simple static initialization for the
cmd variable.
* Use FIELD_PREP to assign the node_type_ctx.
* Remove an unnecessary local variable to keep track of rec_node_handle,
just pass the node_handle pointer directly into ice_aq_get_netlist_node.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 19 Oct 2023 17:32:24 +0000 (10:32 -0700)]
ice: make ice_get_pf_c827_idx static
The ice_get_pf_c827_idx function is only called inside of ice_ptp_hw.c, so
there is no reason to export it. Mark it static and remove the declaration
from ice_ptp_hw.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Swiatkowski [Thu, 19 Oct 2023 17:32:23 +0000 (10:32 -0700)]
ice: manage VFs MSI-X using resource tracking
Track MSI-X for VFs using bitmap, by setting and clearing bitmap during
allocation and freeing.
Try to linearize irqs usage for VFs, by freeing them and allocating once
again. Do it only for VFs that aren't currently running.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Swiatkowski [Thu, 19 Oct 2023 17:32:22 +0000 (10:32 -0700)]
ice: set MSI-X vector count on VF
Implement ops needed to set MSI-X vector count on VF.
sriov_get_vf_total_msix() should return total number of MSI-X that can
be used by the VFs. Return the value set by devlink resources API
(pf->req_msix.vf).
sriov_set_msix_vec_count() will set number of MSI-X on particular VF.
Disable VF register mapping, rebuild VSI with new MSI-X and queues
values and enable new VF register mapping.
For best performance set number of queues equal to number of MSI-X.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Swiatkowski [Thu, 19 Oct 2023 17:32:21 +0000 (10:32 -0700)]
ice: add bitmap to track VF MSI-X usage
Create a bitamp to track MSI-X usage for VFs. The bitmap has the size of
total MSI-X amount on device, because at init time the amount of MSI-X
used by VFs isn't known.
The bitmap is used in follow up patchset to provide a block of
continuous block of MSI-X indexes for each created VF.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Swiatkowski [Thu, 19 Oct 2023 17:32:20 +0000 (10:32 -0700)]
ice: implement num_msix field per VF
Store the amount of MSI-X per VF instead of storing it in pf struct. It
is used to calculate number of q_vectors (and queues) for VF VSI.
This is necessary because with follow up changes the number of MSI-X can
be different between VFs. Use it instead of using pf->vf_msix value in
all cases.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Swiatkowski [Thu, 19 Oct 2023 17:32:18 +0000 (10:32 -0700)]
ice: add drop rule matching on not active lport
Inactive LAG port should not receive any packets, as it can cause adding
invalid FDBs (bridge offload). Add a drop rule matching on inactive lport
in LAG.
Reviewed-by: Simon Horman <horms@kernel.org> Co-developed-by: Marcin Szycik <marcin.szycik@intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Przemek Kitszel [Thu, 19 Oct 2023 17:32:17 +0000 (10:32 -0700)]
ice: remove unused ice_flow_entry fields
Remove ::entry and ::entry_sz fields of &ice_flow_entry,
as they were never set.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 19 Oct 2023 15:28:15 +0000 (08:28 -0700)]
ethtool: untangle the linkmode and ethtool headers
Commit 26c5334d344d ("ethtool: Add forced speed to supported link
modes maps") added a dependency between ethtool.h and linkmode.h.
The dependency in the opposite direction already exists so the
new code was inserted in an awkward place.
The reason for ethtool.h to include linkmode.h, is that
ethtool_forced_speed_maps_init() is a static inline helper.
That's not really necessary.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Paul Greenwalt <paul.greenwalt@intel.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heng Guo [Thu, 19 Oct 2023 01:20:53 +0000 (09:20 +0800)]
net: fix IPSTATS_MIB_OUTPKGS increment in OutForwDatagrams.
Reproduce environment:
network with 3 VM linuxs is connected as below:
VM1<---->VM2(latest kernel 6.5.0-rc7)<---->VM3
VM1: eth0 ip: 192.168.122.207 MTU 1500
VM2: eth0 ip: 192.168.122.208, eth1 ip: 192.168.123.224 MTU 1500
VM3: eth0 ip: 192.168.123.240 MTU 1500
Reproduce:
VM1 send 1400 bytes UDP data to VM3 using tools scapy with flags=0.
scapy command:
send(IP(dst="192.168.123.240",flags=0)/UDP()/str('0'*1400),count=1,
inter=1.000000)
Result:
Before IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails
FragOKs FragFails FragCreates
Ip: 1 64 11 0 3 4 0 0 4 7 0 0 0 0 0 0 0 0 0
......
----------------------------------------------------------------------
After IP data is sent.
----------------------------------------------------------------------
root@qemux86-64:~# cat /proc/net/snmp
Ip: Forwarding DefaultTTL InReceives InHdrErrors InAddrErrors
ForwDatagrams InUnknownProtos InDiscards InDelivers OutRequests
OutDiscards OutNoRoutes ReasmTimeout ReasmReqds ReasmOKs ReasmFails
FragOKs FragFails FragCreates
Ip: 1 64 12 0 3 5 0 0 4 8 0 0 0 0 0 0 0 0 0
......
----------------------------------------------------------------------
"ForwDatagrams" increase from 4 to 5 and "OutRequests" also increase
from 7 to 8.
Issue description and patch:
IPSTATS_MIB_OUTPKTS("OutRequests") is counted with IPSTATS_MIB_OUTOCTETS
("OutOctets") in ip_finish_output2().
According to RFC 4293, it is "OutOctets" counted with "OutTransmits" but
not "OutRequests". "OutRequests" does not include any datagrams counted
in "ForwDatagrams".
ipSystemStatsOutOctets OBJECT-TYPE
DESCRIPTION
"The total number of octets in IP datagrams delivered to the
lower layers for transmission. Octets from datagrams
counted in ipIfStatsOutTransmits MUST be counted here.
ipSystemStatsOutRequests OBJECT-TYPE
DESCRIPTION
"The total number of IP datagrams that local IP user-
protocols (including ICMP) supplied to IP in requests for
transmission. Note that this counter does not include any
datagrams counted in ipSystemStatsOutForwDatagrams.
So do patch to define IPSTATS_MIB_OUTPKTS to "OutTransmits" and add
IPSTATS_MIB_OUTREQUESTS for "OutRequests".
Add IPSTATS_MIB_OUTREQUESTS counter in __ip_local_out() for ipv4 and add
IPSTATS_MIB_OUT counter in ip6_finish_output2() for ipv6.
Signed-off-by: Heng Guo <heng.guo@windriver.com> Reviewed-by: Kun Song <Kun.Song@windriver.com> Reviewed-by: Filip Pudak <filip.pudak@windriver.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Oct 2023 10:50:46 +0000 (11:50 +0100)]
Merge branch 'ksz886x-forced-link-modes'
Oleksij Rempel says:
====================
fix forced link mode for KSZ886X switches
changes v3:
- squash patch 1 and 2
- use genphy_config_aneg() instead of genphy_setup_forced()
changes v2:
- address kernel test robot warning
- change comment explaining clearing of KSZ886X_CTRL_FORCE_LINK bit
- s/PHY we create/PHY will create/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Thu, 19 Oct 2023 11:14:59 +0000 (13:14 +0200)]
net: phy: micrel: Fix forced link mode for KSZ886X switches
Address a link speed detection issue in KSZ886X PHY driver when in
forced link mode. Previously, link partners like "ASIX AX88772B"
with KSZ8873 could fall back to 10Mbit instead of configured 100Mbit.
The issue arises as KSZ886X PHY continues sending Fast Link Pulses (FLPs)
even with autonegotiation off, misleading link partners in autoneg mode,
leading to incorrect link speed detection.
Now, when autonegotiation is disabled, the driver sets the link state
forcefully using KSZ886X_CTRL_FORCE_LINK bit. This action, beyond just
disabling autonegotiation, makes the PHY state more reliably detected by
link partners using parallel detection, thus fixing the link speed
misconfiguration.
With autonegotiation enabled, link state is not forced, allowing proper
autonegotiation process participation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Divya Koppera <divya.koppera@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Thu, 19 Oct 2023 11:14:58 +0000 (13:14 +0200)]
net: dsa: microchip: ksz8: Enable MIIM PHY Control reg access
Provide access to MIIM PHY Control register (Reg. 31) through
ksz8_r_phy_ctrl() and ksz8_w_phy_ctrl() functions. Necessary for
upcoming micrel.c patch to address forced link mode configuration.
Closes: https://lore.kernel.org/oe-kbuild-all/202310112224.iYgvjBUy-lkp@intel.com/ Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Oct 2023 10:47:51 +0000 (11:47 +0100)]
Merge branch 'mlxsw-lag-table-allocation'
Petr Machata says:
====================
mlxsw: Move allocation of LAG table to the driver
PGT is an in-HW table that maps addresses to sets of ports. Then when some
HW process needs a set of ports as an argument, instead of embedding the
actual set in the dynamic configuration, what gets configured is the
address referencing the set. The HW then works with the appropriate PGT
entry.
Within the PGT is placed a LAG table. That is a contiguous block of PGT
memory where each entry describes which ports are members of the
corresponding LAG port.
The PGT is split to two parts: one managed by the FW, and one managed by
the driver. Historically, the FW part included also the LAG table, referred
to as FW LAG mode. Giving the responsibility for placement of the LAG table
to the driver, referred to as SW LAG mode, makes the whole system more
flexible. The FW currently supports both FW and SW LAG modes. To shed
complexity, the FW should in the future only support SW LAG mode.
Hence this patchset, where support for placement of LAG is added to mlxsw.
There are FW versions out there that do not support SW LAG mode, and on
Spectrum-1 in particular, there is no plan to support it at all. mlxsw will
therefore have to support both modes of operation.
Another aspect is that at least on Spectrum-1, there are FW versions out
there that claim to support driver-placed LAG table, but then reject or
ignore configurations enabling the same. The driver thus has to have a say
in whether an attempt to configure SW LAG mode should even be done.
The feature is therefore expressed in terms of "does the driver prefer SW
LAG mode?", and "what LAG mode the PCI module managed to configure the FW
with". This is unlike current flood mode configuration, where the driver
can give a strict value, and that's what gets configured. But it gives a
chance to the driver to determine whether LAG mode should be enabled at
all.
The "does the driver prefer SW LAG mode?" bit is expressed as a boolean
lag_mode_prefer_sw. The reason for this is largely another feature that
will be introduced in a follow-up patchset: support for CFF flood mode. The
driver currently requires that the FW be configured with what is called
controlled flood mode. But on capable systems, CFF would be preferred. So
there are two values in flight: the preferred flood mode, and the fallback.
This could be expressed with an array of flood modes ordered by preference,
but that looks like an overkill in comparison. This flag/value model is
then reused for LAG mode as well, except the fallback value is absent and
implied to be FW, because there are no other values to choose from.
The patchset progresses as follows:
- Patches #1 to #5 adjust reg.h and cmd.h with new register fields,
constants and remarks.
- Patches #6 and #7 add the ability to request SW LAG mode and to query the
LAG mode that was actually negotiated. This is where the abovementioned
lag_mode_prefer_sw flag is added.
- Patches #7 to #9 generalize PGT allocations to make it possible to
allocate the LAG table, which is done in patch #10.
- In patch #11, toggle lag_mode_prefer_sw on Spectrum-2 and above, which
makes the newly-added code live.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:20 +0000 (12:27 +0200)]
mlxsw: spectrum: Set SW LAG mode on Spectrum>1
On Spectrum-2, Spectrum-3 and Spectrum-4 machines, request SW
responsibility for placement of the LAG table.
On Spectrum-1, some FW versions claim to support lag_mode field despite
quietly ignoring any settings made to that field. Thus refrain from
attempting to configure lag_mode on those systems at all.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:19 +0000 (12:27 +0200)]
mlxsw: spectrum: Allocate LAG table when in SW LAG mode
In this patch, if the LAG mode is SW, allocate the LAG table and configure
SGCR to indicate where it was allocated.
We use the default "DDD" (for dynamic data duplication) layout of the LAG
table. In the DDD mode, the membership information for each LAG is copied
in 8 PGT entries. This is done for performance reasons. The LAG table then
needs to be allocated on an address aligned to 8. Deal with this by
moving the LAG init ahead so that the LAG table is allocated at address 0.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:18 +0000 (12:27 +0200)]
mlxsw: spectrum_pgt: Generalize PGT allocation
PGT blocks are allocated through the function
mlxsw_sp_pgt_mid_alloc_range(). The interface assumes that the caller knows
which piece of PGT exactly they want to get. That was fine while the FID
code was the only client allocating blocks of PGT. However for SW-allocated
LAG table, there will be an additional client: mlxsw_sp_lag_init(). The
interface should therefore be changed to not require particular
coordinates, but to take just the requested size, allocate the block
wherever, and give back the PGT address.
In this patch, change the interface accordingly. Initialize FID family's
pgt_base from the result of the PGT allocation (note that mlxsw makes a
copy of the family structure, so what gets initialized is not actually the
global structure). Drop the now-unnecessary pgt_base initializations and
the corresponding defines.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:17 +0000 (12:27 +0200)]
mlxsw: spectrum_fid: Allocate PGT for the whole FID family in one go
PGT blocks are allocated through the function
mlxsw_sp_pgt_mid_alloc_range(). The interface assumes that the caller knows
which piece of PGT exactly they want to get. That was fine while the FID
code was the only client allocating blocks of PGT. However for SW-allocated
LAG table, there will be an additional client: mlxsw_sp_lag_init(). The
interface should therefore be changed to not require particular
coordinates, but to take just the requested size, allocate the block
wherever, and give back the PGT address.
The current FID mode has one place where PGT address can be stored: the FID
family's pgt_base. The allocation scheme should therefore be changed from
allocating a block per FID flood table, to allocating a block per FID
family.
Do just that in this patch.
The per-family allocation is going to be useful for another related feature
as well: the CFF mode.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:16 +0000 (12:27 +0200)]
mlxsw: pci: Permit toggling LAG mode
Add to struct mlxsw_config_profile a field lag_mode_prefer_sw for the
driver to indicate that SW LAG mode should be configured if possible. Add
to the PCI module code to set lag_mode as appropriate.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:15 +0000 (12:27 +0200)]
mlxsw: core, pci: Add plumbing related to LAG mode
lag_mode describes where the responsibility for LAG table placement lies:
SW or FW. The bus module determines whether LAG is supported, can configure
it if it is, and knows what (if any) configuration has been applied.
Therefore add a bus callback to determine the configured LAG mode. Also add
to core an API to query it.
The LAG mode is for now kept at the default value of 0 for FW-managed. The
code to actually toggle it will be added later.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:13 +0000 (12:27 +0200)]
mlxsw: cmd: Add CONFIG_PROFILE.{set_, }lag_mode
Add CONFIG_PROFILE.lag_mode, which serves for moving responsibility for
placement of the LAG table from FW to SW. Whether lag_mode should be
configured is determined by CONFIG_PROFILE.set_lag_mode, which also add.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:12 +0000 (12:27 +0200)]
mlxsw: cmd: Fix omissions in CONFIG_PROFILE field names in comments
A number of CONFIG_PROFILE fields' comments refer to a field named like
cmd_mbox_config_* instead of cmd_mbox_config_profile_*. Correct these
omissions.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:11 +0000 (12:27 +0200)]
mlxsw: reg: Add SGCR.lag_lookup_pgt_base
Add SGCR.lag_lookup_pgt_base, which is used for configuring the base
address of the LAG table within the PGT table for cases when the driver
is responsible for the table placement.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 19 Oct 2023 10:27:10 +0000 (12:27 +0200)]
mlxsw: reg: Drop SGCR.llb
SGCR, Switch General Configuration Register, has not been used since commit b0d80c013b04 ("mlxsw: Remove Mellanox SwitchX-2 ASIC support"). We will
need the register again shortly, so instead of dropping it and
reintroducing again, just drop the sole unused field.
Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Oct 2023 10:43:36 +0000 (11:43 +0100)]
Merge branch 'netlink-auto-integers'
Jakub Kicinski says:
====================
netlink: add variable-length / auto integers
Add netlink support for "common" / variable-length / auto integers
which are carried at the message level as either 4B or 8B depending
on the exact value. This saves space and will hopefully decrease
the number of instances where we realize that we needed more bits
after uAPI is set is stone. It also loosens the alignment requirements,
avoiding the need for padding.
This mini-series is a fuller version of the previous RFC:
https://lore.kernel.org/netdev/20121204.130914.1457976839967676240.davem@davemloft.net/
No user included here. I have tested (and will use) it
in the upcoming page pool API but the assumption is that
it will be widely applicable. So sending without a user.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 18 Oct 2023 21:39:21 +0000 (14:39 -0700)]
netlink: specs: add support for auto-sized scalars
Support uint / sint types in specs and YNL.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 18 Oct 2023 21:39:20 +0000 (14:39 -0700)]
netlink: add variable-length / auto integers
We currently push everyone to use padding to align 64b values
in netlink. Un-padded nla_put_u64() doesn't even exist any more.
The story behind this possibly start with this thread:
https://lore.kernel.org/netdev/20121204.130914.1457976839967676240.davem@davemloft.net/
where DaveM was concerned about the alignment of a structure
containing 64b stats. If user space tries to access such struct
directly:
lack of alignment may become problematic for some architectures.
These days we most often put every single member in a separate
attribute, meaning that the code above would use a helper like
nla_get_u64(), which can deal with alignment internally.
Even for arches which don't have good unaligned access - access
aligned to 4B should be pretty efficient.
Kernel and well known libraries deal with unaligned input already.
Padded 64b is quite space-inefficient (64b + pad means at worst 16B
per attr vs 32b which takes 8B). It is also more typing:
if (nla_put_u64_pad(rsp, NETDEV_A_SOMETHING_SOMETHING,
value, NETDEV_A_SOMETHING_PAD))
Create a new attribute type which will use 32 bits at netlink
level if value is small enough (probably most of the time?),
and (4B-aligned) 64 bits otherwise. Kernel API is just:
if (nla_put_uint(rsp, NETDEV_A_SOMETHING_SOMETHING, value))
Calling this new type "just" sint / uint with no specific size
will hopefully also make people more comfortable with using it.
Currently telling people "don't use u8, you may need the bits,
and netlink will round up to 4B, anyway" is the #1 comment
we give to newcomers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Oct 2023 10:34:51 +0000 (11:34 +0100)]
Merge branch 'devlink-errors-fmsg'
Przemek Kitszel says:
====================
devlink: retain error in struct devlink_fmsg
Extend devlink fmsg to retain error (patch 1),
so drivers could omit error checks after devlink_fmsg_*() (patches 2-10),
and finally enforce future uses to follow this practice by change to
return void (patch 11)
Przemek Kitszel [Wed, 18 Oct 2023 20:26:47 +0000 (22:26 +0200)]
devlink: convert most of devlink_fmsg_*() to return void
Since struct devlink_fmsg retains error by now (see 1st patch of this
series), there is no longer need to keep returning it in each call.
This is a separate commit to allow per-driver conversion to stop using
those return values.
Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Przemek Kitszel [Wed, 18 Oct 2023 20:26:46 +0000 (22:26 +0200)]
staging: qlge: devlink health: use retained error fmsg API
Drop unneeded error checking.
devlink_fmsg_*() family of functions is now retaining errors,
so there is no need to check for them after each call.
Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Przemek Kitszel [Wed, 18 Oct 2023 20:26:45 +0000 (22:26 +0200)]
qed: devlink health: use retained error fmsg API
Drop unneeded error checking.
devlink_fmsg_*() family of functions is now retaining errors,
so there is no need to check for them after each call.
Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Przemek Kitszel [Wed, 18 Oct 2023 20:26:39 +0000 (22:26 +0200)]
pds_core: devlink health: use retained error fmsg API
Drop unneeded error checking.
devlink_fmsg_*() family of functions is now retaining errors,
so there is no need to check for them after each call.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Przemek Kitszel [Wed, 18 Oct 2023 20:26:38 +0000 (22:26 +0200)]
netdevsim: devlink health: use retained error fmsg API
Drop unneeded error checking.
devlink_fmsg_*() family of functions is now retaining errors,
so there is no need to check for them after each call.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Przemek Kitszel [Wed, 18 Oct 2023 20:26:37 +0000 (22:26 +0200)]
devlink: retain error in struct devlink_fmsg
Retain error value in struct devlink_fmsg, to relieve drivers from
checking it after each call.
Note that fmsg is an in-memory builder/buffer of formatted message,
so it's not the case that half baked message was sent somewhere.
We could find following scheme in multiple drivers:
err = devlink_fmsg_obj_nest_start(fmsg);
if (err)
return err;
err = devlink_fmsg_string_pair_put(fmsg, "src", src);
if (err)
return err;
err = devlink_fmsg_something(fmsg, foo, bar);
if (err)
return err;
// and so on...
err = devlink_fmsg_obj_nest_end(fmsg);
With retaining error API that translates to:
devlink_fmsg_obj_nest_start(fmsg);
devlink_fmsg_string_pair_put(fmsg, "src", src);
devlink_fmsg_something(fmsg, foo, bar);
// and so on...
devlink_fmsg_obj_nest_end(fmsg);
What means we check error just when is time to send.
Possible error scenarios are developer error (API misuse) and memory
exhaustion, both cases are good candidates to choose readability
over fastest possible exit.
Note that this patch keeps returning errors, to allow per-driver conversion
to the new API, but those are not needed at this point already.
This commit itself is an illustration of benefits for the dev-user,
more of it will be in separate commits of the series.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tools: ynl-gen: support full range of min/max checks
YNL code gen currently supports only very simple range checks
within the range of s16. Add support for full range of u64 / s64
which is good to have, and will be even more important with uint / sint.
====================
Jakub Kicinski [Wed, 18 Oct 2023 16:39:16 +0000 (09:39 -0700)]
tools: ynl-gen: support full range of min/max checks for integer values
Extend the support to full range of min/max checks.
None of the existing YNL families required complex integer validation.
The support is less than trivial, because we try to keep struct nla_policy
tiny the min/max members it holds in place are s16. Meaning we can only
express checks in range of s16. For larger ranges we need to define
a structure and link it in the policy.
Jakub Kicinski [Wed, 18 Oct 2023 16:39:15 +0000 (09:39 -0700)]
tools: ynl-gen: track attribute use
For range validation we'll need to know if any individual
attribute is used on input (i.e. whether we will generate
a policy for it). Track this information.
Linus Torvalds [Thu, 19 Oct 2023 19:08:18 +0000 (12:08 -0700)]
Merge tag 'net-6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, netfilter, WiFi.
Feels like an up-tick in regression fixes, mostly for older releases.
The hfsc fix, tcp_disconnect() and Intel WWAN fixes stand out as
fairly clear-cut user reported regressions. The mlx5 DMA bug was
causing strife for 390x folks. The fixes themselves are not
particularly scary, tho. No open investigations / outstanding reports
at the time of writing.
Current release - regressions:
- eth: mlx5: perform DMA operations in the right locations, make
devices usable on s390x, again
- sched: sch_hfsc: upgrade 'rt' to 'sc' when it becomes a inner
curve, previous fix of rejecting invalid config broke some scripts
- rfkill: reduce data->mtx scope in rfkill_fop_open, avoid deadlock
- revert "ethtool: Fix mod state of verbose no_mask bitset", needs
more work
Current release - new code bugs:
- tcp: fix listen() warning with v4-mapped-v6 address
Previous releases - regressions:
- tcp: allow tcp_disconnect() again when threads are waiting, it was
denied to plug a constant source of bugs but turns out .NET depends
on it
- eth: mlx5: fix double-free if buffer refill fails under OOM
- revert "net: wwan: iosm: enable runtime pm support for 7560", it's
causing regressions and the WWAN team at Intel disappeared
- tcp: tsq: relax tcp_small_queue_check() when rtx queue contains a
single skb, fix single-stream perf regression on some devices
Previous releases - always broken:
- Bluetooth:
- fix issues in legacy BR/EDR PIN code pairing
- correctly bounds check and pad HCI_MON_NEW_INDEX name
- netfilter:
- more fixes / follow ups for the large "commit protocol" rework,
which went in as a fix to 6.5
- fix null-derefs on netlink attrs which user may not pass in
- tcp: fix excessive TLP and RACK timeouts from HZ rounding (bless
Debian for keeping HZ=250 alive)
- net: more strict VIRTIO_NET_HDR_GSO_UDP_L4 validation, prevent
letting frankenstein UDP super-frames from getting into the stack
- net: fix interface altnames when ifc moves to a new namespace
- eth: qed: fix the size of the RX buffers
- mptcp: avoid sending RST when closing the initial subflow"
* tag 'net-6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
Revert "ethtool: Fix mod state of verbose no_mask bitset"
selftests: mptcp: join: no RST when rm subflow/addr
mptcp: avoid sending RST when closing the initial subflow
mptcp: more conservative check for zero probes
tcp: check mptcp-level constraints for backlog coalescing
selftests: mptcp: join: correctly check for no RST
net: ti: icssg-prueth: Fix r30 CMDs bitmasks
selftests: net: add very basic test for netdev names and namespaces
net: move altnames together with the netdevice
net: avoid UAF on deleted altname
net: check for altname conflicts when changing netdev's netns
net: fix ifname in netlink ntf during netns move
net: ethernet: ti: Fix mixed module-builtin object
net: phy: bcm7xxx: Add missing 16nm EPHY statistics
ipv4: fib: annotate races around nh->nh_saddr_genid and nh->nh_saddr
tcp_bpf: properly release resources on error paths
net/sched: sch_hfsc: upgrade 'rt' to 'sc' when it becomes a inner curve
net: mdio-mux: fix C45 access returning -EIO after API change
tcp: tsq: relax tcp_small_queue_check() when rtx queue contains a single skb
octeon_ep: update BQL sent bytes before ringing doorbell
...
Linus Torvalds [Thu, 19 Oct 2023 18:02:28 +0000 (11:02 -0700)]
Merge tag 'loongarch-fixes-6.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai ChenL
"Fix 4-level pagetable building, disable WUC for pgprot_writecombine()
like ioremap_wc(), use correct annotation for exception handlers, and
a trivial cleanup"
* tag 'loongarch-fixes-6.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: Disable WUC for pgprot_writecombine() like ioremap_wc()
LoongArch: Replace kmap_atomic() with kmap_local_page() in copy_user_highpage()
LoongArch: Export symbol invalid_pud_table for modules building
LoongArch: Use SYM_CODE_* to annotate exception handlers
Linus Torvalds [Thu, 19 Oct 2023 17:53:31 +0000 (10:53 -0700)]
Merge tag 'slab-fixes-for-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fix from Vlastimil Babka:
- stable fix to prevent kernel warnings with KASAN_HW_TAGS on arm64
due to improperly resolved kmalloc alignment restrictions (Catalin
Marinas)
* tag 'slab-fixes-for-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm: slab: Do not create kmalloc caches smaller than arch_slab_minalign()
Linus Torvalds [Thu, 19 Oct 2023 16:37:41 +0000 (09:37 -0700)]
Merge tag 'v6.6-rc7.vfs.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fix from Christian Brauner:
"An openat() call from io_uring triggering an audit call can apparently
cause the refcount of struct filename to be incremented from multiple
threads concurrently during async execution, triggering a refcount
underflow and hitting a BUG_ON(). That bug has been lurking around
since at least v5.16 apparently.
Switch to an atomic counter to fix that. The underflow check is
downgraded from a BUG_ON() to a WARN_ON_ONCE() but we could easily
remove that check altogether tbh"
* tag 'v6.6-rc7.vfs.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
audit,io_uring: io_uring openat triggers audit reference count underflow
It was reported that this fix breaks the possibility to remove existing WoL
flags. For example:
~$ ethtool lan2
...
Supports Wake-on: pg
Wake-on: d
...
~$ ethtool -s lan2 wol gp
~$ ethtool lan2
...
Wake-on: pg
...
~$ ethtool -s lan2 wol d
~$ ethtool lan2
...
Wake-on: pg
...
This worked correctly before this commit because we were always updating
a zero bitmap (since commit 6699170376ab ("ethtool: fix application of
verbose no_mask bitset"), that is) so that the rest was left zero
naturally. But now the 1->0 change (old_val is true, bit not present in
netlink nest) no longer works.
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de> Reported-by: Michal Kubecek <mkubecek@suse.cz> Closes: https://lore.kernel.org/netdev/20231019095140.l6fffnszraeb6iiw@lion.mk-sys.cz/ Cc: stable@vger.kernel.org Fixes: 108a36d07c01 ("ethtool: Fix mod state of verbose no_mask bitset") Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Link: https://lore.kernel.org/r/20231019-feature_ptp_bitset_fix-v1-1-70f3c429a221@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 19 Oct 2023 16:10:18 +0000 (09:10 -0700)]
Merge tag 'ntfs3_for_6.6' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 fixes from Konstantin Komarov:
- memory leak
- some logic errors, NULL dereferences
- some code was refactored
- more sanity checks
* tag 'ntfs3_for_6.6' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Avoid possible memory leak
fs/ntfs3: Fix directory element type detection
fs/ntfs3: Fix possible null-pointer dereference in hdr_find_e()
fs/ntfs3: Fix OOB read in ntfs_init_from_boot
fs/ntfs3: fix panic about slab-out-of-bounds caused by ntfs_list_ea()
fs/ntfs3: Fix NULL pointer dereference on error in attr_allocate_frame()
fs/ntfs3: Fix possible NULL-ptr-deref in ni_readpage_cmpr()
fs/ntfs3: Do not allow to change label if volume is read-only
fs/ntfs3: Add more info into /proc/fs/ntfs3/<dev>/volinfo
fs/ntfs3: Refactoring and comments
fs/ntfs3: Fix alternative boot searching
fs/ntfs3: Allow repeated call to ntfs3_put_sbi
fs/ntfs3: Use inode_set_ctime_to_ts instead of inode_set_ctime
fs/ntfs3: Fix shift-out-of-bounds in ntfs_fill_super
fs/ntfs3: fix deadlock in mark_as_free_ex
fs/ntfs3: Add more attributes checks in mi_enum_attr()
fs/ntfs3: Use kvmalloc instead of kmalloc(... __GFP_NOWARN)
fs/ntfs3: Write immediately updated ntfs state
fs/ntfs3: Add ckeck in ni_update_parent()
Geliang Tang [Wed, 18 Oct 2023 18:23:55 +0000 (11:23 -0700)]
mptcp: avoid sending RST when closing the initial subflow
When closing the first subflow, the MPTCP protocol unconditionally
calls tcp_disconnect(), which in turn generates a reset if the subflow
is established.
That is unexpected and different from what MPTCP does with MPJ
subflows, where resets are generated only on FASTCLOSE and other edge
scenarios.
We can't reuse for the first subflow the same code in place for MPJ
subflows, as MPTCP clean them up completely via a tcp_close() call,
while must keep the first subflow socket alive for later re-usage, due
to implementation constraints.
This patch adds a new helper __mptcp_subflow_disconnect() that
encapsulates, a logic similar to tcp_close, issuing a reset only when
the MPTCP_CF_FASTCLOSE flag is set, and performing a clean shutdown
otherwise.
Fixes: c2b2ae3925b6 ("mptcp: handle correctly disconnect() failures") Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matttbe@kernel.org> Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Link: https://lore.kernel.org/r/20231018-send-net-20231018-v1-4-17ecb002e41d@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / users / hch / misc.git / log