Li Yang [Thu, 15 Sep 2022 23:34:31 +0000 (18:34 -0500)]
arm64: dts: ls1046a-qds: add mmio based mdio-mux nodes for FPGA
There is mmio based mdio mux function in the FPGA device on ls1046a-qds
board. Add the mmio based mdio-mux nodes to ls1043a-qds boards and
add simple-mfd as a compatbile for the FPGA node to reflect the
multi-function nature of it.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: ls1046a: use a pseudo-bus to constrain usb and sata dma size
Wrap the usb and sata controllers in an intermediate simple-bus and use
it to constrain the dma address size of these usb controllers to the 40
bits that they generate toward the interconnect. This is required
because the SoC uses 48 bits address sizes and this mismatch would lead
to smmu context faults because the usb generates 40-bit addresses while
the smmu page tables are populated with 48-bit wide addresses.
Suggested-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Thu, 15 Sep 2022 23:34:28 +0000 (18:34 -0500)]
arm64: dts: ls1046a: make dma-coherent global to the SoC
These SoCs are really completely dma coherent in their entirety so add
the dma-coherent property at the soc level in the device tree and drop
the instances where it's specifically added to a few select devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These chips have a 48-bit address size so make sure that the dma-ranges
reflects this. Otherwise the linux kernel's dma sub-system will set
the default dma masks to full 64-bit, badly breaking dmas.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Wed, 14 Sep 2022 21:47:02 +0000 (16:47 -0500)]
arm64: dts: ls1043a-qds: add mmio based mdio-mux support
There is mmio based mdio mux function in the FPGA device on ls1043a-qds
board. Add the mmio based mdio-mux nodes to ls1043a-qds boards and
add simple-mfd as a compatbile for the FPGA node to reflect the
multi-function nature of it. Also connect the ethernet interfaces to
these phy interfaces.
Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: ls1043a: use a pseudo-bus to constrain usb and sata dma size
Wrap the usb and sata controllers in an intermediate simple-bus and use
it to constrain the dma address size of these usb controllers to the 40
bits that they generate toward the interconnect. This is required
because the SoC uses 48 bits address sizes and this mismatch would lead
to smmu context faults because the usb generates 40-bit addresses while
the smmu page tables are populated with 48-bit wide addresses.
Suggested-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Wed, 14 Sep 2022 21:46:59 +0000 (16:46 -0500)]
arm64: dts: ls1043a: make dma-coherent global to the SoC
ls1043a is really completely dma coherent in their entirety so add the
dma-coherent property at the soc level in the device tree and drop the
instances where it's specifically added to a few select devices.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1043a has a 48-bit address size so make sure that the dma-ranges
reflects this. Otherwise the linux kernel's dma sub-system will set the
default dma masks to full 64-bit, badly breaking dmas.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Li Yang [Wed, 14 Sep 2022 21:46:55 +0000 (16:46 -0500)]
arm64: dts: ls1043a: use pcie aer/pme interrupts
After the binding has been updated to include more specific interrupt
definition, update the dts to use the more specific interrupt names.
Signed-off-by: Po Liu <po.liu@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: ls208x: remove NXP Erratum A008585 from LS2088A.
NXP Erratum A008585 affects A57 core cluster used in LS2085 rev1.
However this problem has been fixed in A72 core cluster used in LS2088.
Therefore remove the erratum from LS2088A. Keeping it only in LS2085.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Reviewed-by: Sandeep Malik <sandeep.malik@nxp.com> Acked-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Biwen Li [Wed, 14 Sep 2022 21:15:37 +0000 (16:15 -0500)]
arm64: dts: ls208xa-rdb: fix errata E-00013
Specify a channel zero in idle state to avoid enterring tri-stated state
for PCA9547.
Some information about E-00013:
- Description: I2C1 and I2C3 buses are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus will float.
This makes the I2C bus and its associated downstream devices
inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1 and resistors
R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
driver(PCA954x always on enable status, specify a channel zero in dts to
fix the errata E-00013).
Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
arm64: dts: ls2081a-rdb: Add DTS for NXP LS2081ARDB
This patch adds support for NXP LS2081ARDB board which has LS2081A SoC.
LS2081A SoC is 40-pin derivative of LS2088A SoC. From functional
perspective both are same. Hence, LS2088a SoC dtsi file is included
from LS2081ARDB dts.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Tao Yang <b31903@freescale.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shenwei Wang [Wed, 14 Sep 2022 13:58:48 +0000 (08:58 -0500)]
arm64: dts: freescale: add support for i.MX8DXL EVK board
This is to support the EVK (Evaluation Kit Board) for the i.MX8DXL.
The patch has enabled the serial console, SD/EMMC interface, and
the eqos and fec ethernet network.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shenwei Wang [Wed, 14 Sep 2022 13:58:47 +0000 (08:58 -0500)]
arm64: dts: freescale: add i.MX8DXL SoC support
i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.
This patch adds the basic support for i.MX8DXL SoC.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 12 Sep 2022 18:18:19 +0000 (11:18 -0700)]
arm64: dts: imx: Add i.mx8mm Gateworks gw7904 dts support
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 12 Sep 2022 18:08:36 +0000 (11:08 -0700)]
arm64: dts: imx8mp-venice-gw74xx: add WiFi/BT module support
The GW74xx supports an on-board Laird Connectivity Sterling LWB5+ module
which uses a Cypress CYW4373W chip to provide 1x1 802.11 a/b/g/n/ac +
Bluetooth 5.2.
Add the proper device-tree nodes for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Thu, 8 Sep 2022 15:42:27 +0000 (08:42 -0700)]
arm64: dts: imx8mp-venice-gw74xx: add USB DR support
Add support for USB DR on USB1 interface. Host/Device detection is done
using the usb-role-switch connector with a GPIO as USB1_OTG_ID is not
connected internally.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Oltean [Mon, 5 Sep 2022 21:24:58 +0000 (00:24 +0300)]
arm64: dts: ls1028a-rdb: add more ethernet aliases
Commit "arm64: dts: ls1028a: enable swp5 and eno3 for all boards" which
Shawn declared as applied, but for which I can't find a sha1sum, has
enabled a new Ethernet port on the LS1028A-RDB (&enetc_port3), but
U-Boot, which passes a MAC address to Linux' device tree through the
/aliases node, fails to do this for this newly enabled port.
Fix that by adding more ethernet aliases in the only
backwards-compatible way possible: at the end of the current list.
And since it is possible to very easily convert either swp4 or swp5 to
DSA user ports now (which have a MAC address of their own), using these
U-Boot commands:
it would be good if those DSA user ports (swp4, swp5) gained a valid MAC
address from U-Boot as well. In order for that to work properly,
provision two more ethernet aliases for &mscc_felix_port{4,5} as well.
The resulting ordering is slightly unusual, but to me looks more natural
than eno0, eno2, swp0, swp1, swp2, swp3, eno3, swp4, swp5.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Clark Wang [Wed, 31 Aug 2022 14:25:52 +0000 (22:25 +0800)]
arm64: dts: imx8ulp: increase the clock speed of LPSPI
LPSPI transfer max speed is half of the root clock.
Increase the root clock speed to support faster data transmission.
And update the parent clock of all i2c/spi with IMX8ULP_CLK_FROSC_DIV2
which could produce accurate clock for i2c/spi usage.
Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Properties are not documented so lead to the following error:
'#address-cells', '#size-cells', 'interrupts' do not match any of the regexes: 'pinctrl-[0-9]+'
Fix this by removing unneeded properties.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sebastian Krzyszkowiak [Fri, 2 Sep 2022 08:42:13 +0000 (10:42 +0200)]
arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply
This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the RGB notification leds on the Librem 5 phone.
Use the common defines so we're sure to adhere to the common patterns,
use predefined led colors and functions so we're being warned in case
of deprecations.
Martin Kepplinger [Fri, 2 Sep 2022 08:42:11 +0000 (10:42 +0200)]
arm64: dts: imx8mq-librem5: describe the voice coil motor for focus control
Describe the focus motor that will be used for the rear camera - even
though the rear camera sensor driver is not yet in the mainline. The
focus motor is a separate device and can be controlled already.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Oltean [Wed, 31 Aug 2022 16:01:24 +0000 (19:01 +0300)]
arm64: dts: ls1028a: enable swp5 and eno3 for all boards
In order for the LS1028A based boards to benefit from support for
multiple CPU ports, the second DSA master and its associated CPU port
must be enabled in the device trees. This does not change the default
CPU port from the current port 4.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Michael Walle <michael@walle.cc> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Oltean [Wed, 31 Aug 2022 16:01:22 +0000 (19:01 +0300)]
arm64: dts: ls1028a: move DSA CPU port property to the common SoC dtsi
Since the CPU port 4 of the switch is hardwired inside the SoC to go to
the enetc port 2, this shouldn't be something that the board files need
to set (but whether that CPU port is used or not is another discussion).
So move the DSA "ethernet" property to the common dtsi.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Michael Walle <michael@walle.cc> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Richard Zhu [Fri, 2 Sep 2022 08:58:02 +0000 (16:58 +0800)]
arm64: dts: imx8mp-evk: Add PCIe support
Add PCIe support on i.MX8MP EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Richard Leitner <richard.leitner@skidata.com> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Richard Zhu [Fri, 2 Sep 2022 08:58:01 +0000 (16:58 +0800)]
arm64: dts: imx8mp: Add iMX8MP PCIe support
Add i.MX8MP PCIe support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Tested-by: Marek Vasut <marex@denx.de> Tested-by: Richard Leitner <richard.leitner@skidata.com> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Martyn Welch [Tue, 23 Aug 2022 14:01:22 +0000 (15:01 +0100)]
arm64: dts: imx8mp-msc-sm2s: Add device trees for MSC SM2S-IMX8PLUS SoM and carrier board
Add device trees for one of a number of MSC's (parent company, Avnet)
variants of the SM2S-IMX8PLUS system on module along with the compatible
SM2S-SK-AL-EP1 carrier board. As the name suggests, this family of SoMs use
the NXP i.MX8MP SoC and provide the SMARC module interface.
Frieder Schrempf [Mon, 22 Aug 2022 08:03:51 +0000 (10:03 +0200)]
arm64: dts: imx8mm-kontron: Remove low DDRC operating point
For some reason there is a problem with finding a DDR configuration
that works on all operating points and all LPDDR4 types used on the
SoM. Therefore the bootloader currently doesn't configure the lowest
of the three operating points. Let's also skip this in the kernel
devicetree to make sure it isn't used.
Frieder Schrempf [Mon, 22 Aug 2022 08:03:50 +0000 (10:03 +0200)]
arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO voltage
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Frieder Schrempf [Mon, 22 Aug 2022 08:03:49 +0000 (10:03 +0200)]
arm64: dts: imx8mm-kontron: Adjust compatibles, file names and model strings
The official naming includes "SL" (SoM-Line) or "BL" (Board-Line).
By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.
Shenwei Wang [Wed, 14 Sep 2022 13:58:45 +0000 (08:58 -0500)]
dt-bindings: arm: imx: update fsl.yaml for imx8dxl
i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Martyn Welch [Tue, 23 Aug 2022 14:01:21 +0000 (15:01 +0100)]
dt-bindings: arm: fsl: Add MSC SM2S-IMX8PLUS SoM and SM2-MB-EP1 Carrier
Add DT compatible strings for a combination of the 14N0600E variant of
the Avnet (MSC branded) SM2S-IMX8PLUS SoM on it's own and in combination
with the SM2-MB-EP1 carrier board.
projects / users / jedix / linux-maple.git / log