Fabio Estevam [Thu, 22 Feb 2024 14:34:49 +0000 (11:34 -0300)]
ARM: dts: imx1-apf9328: Fix Ethernet node name
Per davicom,dm9000.yaml, the Ethernet node name should be 'ethernet'.
Change it to fix the following schema warning:
imx1-apf9328.dtb: eth@4,c00000: $nodename:0: 'eth@4,c00000' does not match '^ethernet(@.*)?$'
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
Fabio Estevam [Thu, 22 Feb 2024 14:01:27 +0000 (11:01 -0300)]
ARM: dts: imx28-evk: Use 'eeprom' as the node name
Per at24.yaml, the node name should be 'eeprom'.
Change it accordingly to fix the following schema warning:
imx28-evk.dtb: at24@51: $nodename:0: 'at24@51' does not match '^eeprom@[0-9a-f]{1,2}$'
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#
Li Yang [Wed, 21 Feb 2024 22:15:09 +0000 (17:15 -0500)]
ARM: dts: ls1021a: Enable usb3-lpm-capable for usb3 node
Enable USB3 HW LPM feature.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michal Vokáč [Wed, 14 Feb 2024 09:03:28 +0000 (10:03 +0100)]
ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michal Vokáč [Wed, 14 Feb 2024 09:03:27 +0000 (10:03 +0100)]
ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch") Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Christoph Niedermaier [Thu, 25 Jan 2024 12:46:21 +0000 (13:46 +0100)]
ARM: dts: imx6ull-dhcom: Remove /omit-if-no-ref/ from node usdhc1-pwrseq
Remove /omit-if-no-ref/ from node usdhc1-pwrseq, because if the compile
flag -@ (include symbols) is used the node will always be there. In this
case, GPIO H is not released and therefore cannot be used. Therefore,
remove this node manually from the corresponding devicetree file and
don't rely on /omit-if-no-ref/.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Hiago De Franco [Wed, 24 Jan 2024 14:13:20 +0000 (11:13 -0300)]
ARM: dts: imx: Add support for Apalis Evaluation Board v1.2
Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.
Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Hiago De Franco <hiago.franco@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Josua Mayer [Thu, 18 Jan 2024 15:01:10 +0000 (16:01 +0100)]
ARM: dts: imx6qdl-hummingboard: Add rtc0 and rtc1 aliases to fix hctosys
HummingBoard has two RTCs, first integrated within SoC that can be used to
wake up from sleep - and a second on the carrier board including back-up
battery which is intended for keeping time during power-off.
Add aliases for both, ensuring that the battery-backed clock is primary
rtc and used by default during boot for restoring system time.
Fixes keeping time across power-cycle observed on Debian,
which sets RTC_HCTOSYS_DEVICE="rtc0".
Frieder Schrempf [Tue, 16 Jan 2024 18:10:28 +0000 (19:10 +0100)]
ARM: dts: imx6dl: Add support for Sielaff i.MX6 Solo board
The Sielaff i.MX6 Solo board is used as controller and user interface
in vending machines. It is based on the i.MX6 Solo SoC and features
the following peripherals and interfaces:
* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC
Christoph Niedermaier [Thu, 21 Dec 2023 16:46:33 +0000 (17:46 +0100)]
ARM: dts: imx6ull-dhcor: Remove 900MHz operating point
Due to CPU lifetime consideration of the SoC manufacturer [1] and
the preferred area of operation in the industrial related
environment, set the maximum frequency for each DHCOM i.MX6ULL to
792MHz, as with the industrial type. This is done by removing the
operating point at 900MHz and set the clock-frequency to 792000000.
Alexander Stein [Mon, 18 Dec 2023 12:54:41 +0000 (13:54 +0100)]
ARM: dts: imx7[d]-mba7: hog Mini PCIe signals
PCIE_DIS & PCIE_RST (correctly named W_DISABLE# & PERST#) affect USB
devices as well. So hog them to make USB devices attached to Mini PCIe
connector available, despite PCIe being disabled.
Supply voltages are enabled unconditionally.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 21 Jan 2024 22:01:12 +0000 (14:01 -0800)]
Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs
Pull more bcachefs updates from Kent Overstreet:
"Some fixes, Some refactoring, some minor features:
- Assorted prep work for disk space accounting rewrite
- BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
makes our trigger context more explicit
- A few fixes to avoid excessive transaction restarts on
multithreaded workloads: fstests (in addition to ktest tests) are
now checking slowpath counters, and that's shaking out a few bugs
- Assorted tracepoint improvements
- Starting to break up bcachefs_format.h and move on disk types so
they're with the code they belong to; this will make room to start
documenting the on disk format better.
- A few minor fixes"
* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
bcachefs: Improve inode_to_text()
bcachefs: logged_ops_format.h
bcachefs: reflink_format.h
bcachefs; extents_format.h
bcachefs: ec_format.h
bcachefs: subvolume_format.h
bcachefs: snapshot_format.h
bcachefs: alloc_background_format.h
bcachefs: xattr_format.h
bcachefs: dirent_format.h
bcachefs: inode_format.h
bcachefs; quota_format.h
bcachefs: sb-counters_format.h
bcachefs: counters.c -> sb-counters.c
bcachefs: comment bch_subvolume
bcachefs: bch_snapshot::btime
bcachefs: add missing __GFP_NOWARN
bcachefs: opts->compression can now also be applied in the background
bcachefs: Prep work for variable size btree node buffers
bcachefs: grab s_umount only if snapshotting
...
Linus Torvalds [Sun, 21 Jan 2024 19:14:40 +0000 (11:14 -0800)]
Merge tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers"
* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
clocksource/drivers/ep93xx: Fix error handling during probe
clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
clocksource/timer-riscv: Add riscv_clock_shutdown callback
dt-bindings: timer: Add StarFive JH8100 clint
dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
Kent Overstreet [Tue, 16 Jan 2024 21:20:21 +0000 (16:20 -0500)]
bcachefs: opts->compression can now also be applied in the background
The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Tue, 16 Jan 2024 18:29:59 +0000 (13:29 -0500)]
bcachefs: Prep work for variable size btree node buffers
bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.
And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.
Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
In __bch2_ioctl_subvolume_create(), we grab s_umount unconditionally
and unlock it at the end of the function. There is a comment
"why do we need this lock?" about the lock coming from
commit 42d237320e98 ("bcachefs: Snapshot creation, deletion")
The reason is that __bch2_ioctl_subvolume_create() calls
sync_inodes_sb() which enforce locked s_umount to writeback all dirty
nodes before doing snapshot works.
Fix it by read locking s_umount for snapshotting only and unlocking
s_umount after sync_inodes_sb().
Signed-off-by: Su Yue <glass.su@suse.com> Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Colin Ian King [Tue, 16 Jan 2024 11:07:23 +0000 (11:07 +0000)]
bcachefs: remove redundant variable tmp
The variable tmp is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so tmp can be
removed.
Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the enclosing
expression, the value is never actually read from 'ret'
[deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Tue, 16 Jan 2024 01:37:23 +0000 (20:37 -0500)]
bcachefs: Fix excess transaction restarts in __bchfs_fallocate()
drop_locks_do() should not be used in a fastpath without first trying
the do in nonblocking mode - the unlock and relock will cause excessive
transaction restarts and potentially livelocking with other threads that
are contending for the same locks.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Mon, 15 Jan 2024 22:59:51 +0000 (17:59 -0500)]
bcachefs: Better journal tracepoints
Factor out bch2_journal_bufs_to_text(), and use it in the
journal_entry_full() tracepoint; when we can't get a journal reservation
we need to know the outstanding journal entry sizes to know if the
problem is due to excessive flushing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Mon, 15 Jan 2024 22:56:22 +0000 (17:56 -0500)]
bcachefs: Avoid flushing the journal in the discard path
When issuing discards, we may need to flush the journal if there's too
many buckets that can't be discarded until a journal flush.
But the heuristic was bad; we should be comparing the number of buckets
that need to flushes against the number of free buckets, not the number
of buckets we saw.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Mon, 15 Jan 2024 19:15:26 +0000 (14:15 -0500)]
bcachefs: bch2_kthread_io_clock_wait() no longer sleeps until full amount
Drop t he loop in bch2_kthread_io_clock_wait(): this allows the code
that uses it to be woken up for other reasons, and fixes a bug where
rebalance wouldn't wake up when a scan was requested.
This raises the possibility of spurious wakeups, but callers should
always be able to handle that reasonably well.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Thu, 11 Jan 2024 04:47:04 +0000 (23:47 -0500)]
bcachefs: Reduce would_deadlock restarts
We don't have to take locks in any particular ordering - we'll make
forward progress just fine - but if we try to stick to an ordering, it
can help to avoid excessive would_deadlock transaction restarts.
This tweaks the reflink path to take extents btree locks in the right
order.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Kent Overstreet [Thu, 11 Jan 2024 04:08:30 +0000 (23:08 -0500)]
bcachefs: Don't log errors if BCH_WRITE_ALLOC_NOWAIT
Previously, we added logging in the write path to ensure that any
unexpected errors getting reported to userspace have a log message; but
BCH_WRITE_ALLOC_NOWAIT is a special case, it's used for promotes where
errors are expected and not reported out to userspace - so we need to
silence those.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
- retry (reconnect) improvement including new retrans mount parm, and
handling of two additional return codes that need to be retried on
- two minor cleanup patches and another to remove duplicate query
info code
- two documentation cleanup, and one reviewer email correction"
* tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update iface_last_update on each query-and-update
cifs: handle servers that still advertise multichannel after disabling
cifs: new mount option called retrans
cifs: reschedule periodic query for server interfaces
smb: client: don't clobber ->i_rdev from cached reparse points
smb: client: get rid of smb311_posix_query_path_info()
smb: client: parse owner/group when creating reparse points
smb: client: fix parsing of SMB3.1.1 POSIX create context
cifs: update known bugs mentioned in kernel docs for cifs
cifs: new nt status codes from MS-SMB2
cifs: pick channel for tcon and tdis
cifs: open_cached_dir should not rely on primary channel
smb3: minor documentation updates
Update MAINTAINERS email address
cifs: minor comment cleanup
smb3: show beginning time for per share stats
cifs: remove redundant variable tcon_exist
Linus Torvalds [Sat, 20 Jan 2024 23:03:25 +0000 (15:03 -0800)]
Merge tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- Loongson LS2X APB DMA controller
- sf-pdma: mpfs-pdma support
- Qualcomm X1E80100 GPI dma controller support
Updates:
- Xilinx XDMA updates to support interleaved DMA transfers
- TI PSIL threads for AM62P and J722S and cfg register regions
description
- axi-dmac Improving the cyclic DMA transfers
- Tegra Support dma-channel-mask property
- Remaining platform remove callback returning void conversions
Driver fixes for:
- Xilinx xdma driver operator precedence and initialization fix
- Excess kernel-doc warning fix in imx-sdma xilinx xdma drivers
- format-overflow warning fix for rz-dmac, sh usb dmac drivers
- 'output may be truncated' fix for shdma, fsl-qdma and dw-edma
drivers"
* tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (58 commits)
dmaengine: dw-edma: increase size of 'name' in debugfs code
dmaengine: fsl-qdma: increase size of 'irq_name'
dmaengine: shdma: increase size of 'dev_id'
dmaengine: xilinx: xdma: Fix kernel-doc warnings
dmaengine: usb-dmac: Avoid format-overflow warning
dmaengine: sh: rz-dmac: Avoid format-overflow warning
dmaengine: imx-sdma: fix Excess kernel-doc warnings
dmaengine: xilinx: xdma: Fix initialization location of desc in xdma_channel_isr()
dmaengine: xilinx: xdma: Fix operator precedence in xdma_prep_interleaved_dma()
dmaengine: xilinx: xdma: statify xdma_prep_interleaved_dma
dmaengine: xilinx: xdma: Workaround truncation compilation error
dmaengine: pl330: issue_pending waits until WFP state
dmaengine: xilinx: xdma: Implement interleaved DMA transfers
dmaengine: xilinx: xdma: Prepare the introduction of interleaved DMA transfers
dmaengine: xilinx: xdma: Add transfer error reporting
dmaengine: xilinx: xdma: Add error checking in xdma_channel_isr()
dmaengine: xilinx: xdma: Rework xdma_terminate_all()
dmaengine: xilinx: xdma: Ease dma_pool alignment requirements
dmaengine: xilinx: xdma: Add necessary macro definitions
dmaengine: xilinx: xdma: Get rid of unused code
...
Linus Torvalds [Sat, 20 Jan 2024 22:20:34 +0000 (14:20 -0800)]
Merge tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccinelle updates from Julia Lawall:
"Updates to the device_attr_show semantic patch to reflect the new
guidelines of the Linux kernel documentation.
The problem was identified by Li Zhijian <lizhijian@fujitsu.com>, who
proposed an initial fix"
* tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
coccinelle: device_attr_show: simplify patch case
coccinelle: device_attr_show: Adapt to the latest Documentation/filesystems/sysfs.rst
Aurelien Jarno [Sat, 13 Jan 2024 18:33:31 +0000 (19:33 +0100)]
media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)
This patch replaces max(a, min(b, c)) by clamp(b, a, c) in the solo6x10
driver. This improves the readability and more importantly, for the
solo6x10-p2m.c file, this reduces on my system (x86-64, gcc 13):
- the preprocessed size from 121 MiB to 4.5 MiB;
- the build CPU time from 46.8 s to 1.6 s;
- the build memory from 2786 MiB to 98MiB.
In fine, this allows this relatively simple C file to be built on a
32-bit system.
Reported-by: Jiri Slaby <jirislaby@gmail.com> Closes: https://lore.kernel.org/lkml/18c6df0d-45ed-450c-9eda-95160a2bbb8e@gmail.com/ Cc: <stable@vger.kernel.org> # v6.7+ Suggested-by: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: David Laight <David.Laight@ACULAB.COM> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 9 Jan 2024 00:43:04 +0000 (16:43 -0800)]
execve: open the executable file before doing anything else
No point in allocating a new mm, counting arguments and environment
variables etc if we're just going to return ENOENT.
This patch does expose the fact that 'do_filp_open()' that execve() uses
is still unnecessarily expensive in the failure case, because it
allocates the 'struct file *' early, even if the path lookup (which is
heavily optimized) fails.
So that remains an unnecessary cost in the "no such executable" case,
but it's a separate issue. Regardless, I do not want to do _both_ a
filename_lookup() and a later do_filp_open() like the origin patch by
Josh Triplett did in [1].
Linus Torvalds [Sat, 20 Jan 2024 19:06:04 +0000 (11:06 -0800)]
Merge tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
Linus Torvalds [Sat, 20 Jan 2024 17:42:32 +0000 (09:42 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Final round of fixes that came in too late to send in the first
request.
It's nine bug fixes and one version update (because of a bug fix) and
one set of PCI ID additions. There's one bug fix in the core which is
really a one liner (except that an additional sdev pointer was added
for convenience) and the rest are in drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Add TMF to tmr_list handling
scsi: core: Kick the requeue list after inserting when flushing
scsi: fnic: unlock on error path in fnic_queuecommand()
scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
scsi: smartpqi: Bump driver version to 2.1.26-030
scsi: smartpqi: Fix logical volume rescan race condition
scsi: smartpqi: Add new controller PCI IDs
scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
scsi: ufs: core: Simplify power management during async scan
Linus Torvalds [Sat, 20 Jan 2024 17:24:06 +0000 (09:24 -0800)]
Merge tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Since the large patch series to convert arch/sh to device tree support
has not been finalized yet due to various maintainers still asking for
changes to the series, this ended up being rather small consisting of
just two fixes.
The first patch by Geert Uytterhoeven addresses a build failure in the
EcoVec platform code. And the second patch by Masahiro Yamada removes
an unnecessary $(foreach ...) found in a Makefile of the vsyscall
code.
- Rename missed backlight field from fbdev to dev
- Remove unnecessary $(foreach ...)"
* tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: vsyscall: Remove unnecessary $(foreach ...)
sh: ecovec24: Rename missed backlight field from fbdev to dev
Linus Torvalds [Sat, 20 Jan 2024 17:14:04 +0000 (09:14 -0800)]
Merge tag 'fbdev-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fix from Helge Deller:
"There were various reports from people without any graphics output on
the screen and it turns out one commit triggers the problem.
- Revert 'firmware/sysfb: Clear screen_info state after consuming it'"
* tag 'fbdev-for-6.8-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
Revert "firmware/sysfb: Clear screen_info state after consuming it"
projects / users / jedix / linux-maple.git / log