With the original commit applied, z3fold_zpool_destroy() may get blocked
on wait_event() for indefinite time. Revert this commit for the time
being to get rid of this problem since the issue the original commit
addresses is less severe.
It turns out that the G502 has some issues with hid-logitech-hidpp:
when plugging it in, the driver tries to contact it but it fails.
So the driver bails out leaving only the mouse event node available.
This timeout is problematic as it introduce a delay in the boot,
and having only the mouse event node means that the hardware
macros keys can not be relayed to the userspace.
Filipe and I just gave a shot at the following devices:
G403 Wireless (0xC082)
G703 (0xC087)
G703 Hero (0xC090)
G903 (0xC086)
G903 Hero (0xC091)
G Pro (0xC088)
Reverting the devices we are not sure that works flawlessly.
Reviewed-by: Filipe Laíns <lains@archlinux.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Cc: <stable@vger.kernel.org> Fixes: ba5625c3e272 ("clk: imx: Add clock driver support for imx8mm") Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Abel Vesa <abel.vesa@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by the OpenWRT team, write requests sometimes fail on some
platforms.
Currently to check the state chip_ready() is used correctly as described by
the flash memory S29GL256P11TFI01 datasheet.
Also chip_good() is used to check if the write is succeeded and it was
implemented by the commit fb4a90bfcd6d8 ("[MTD] CFI-0002 - Improve error
checking").
But actually the write failure is caused on some platforms and also it can
be fixed by using chip_good() to check the state and retry instead.
Also it seems that it is caused after repeated about 1,000 times to retry
the write one word with the reset command.
By using chip_good() to check the state to be done it can be reduced the
retry with reset.
It is depended on the actual flash chip behavior so the root cause is
unknown.
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this one as well.
Ville Viinikka (viinikv) reported and tested the quirk. Link: https://github.com/sriemer/fix-linux-mouse Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de> CC: stable@vger.kernel.org # v4.16+ Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer has reported a pair of problems in the
hidraw_ioctl() function: slab-out-of-bounds read and use-after-free
read. An example of the first:
BUG: KASAN: slab-out-of-bounds in strlen+0x79/0x90 lib/string.c:525
Read of size 1 at addr ffff8881c8035f38 by task syz-executor.4/2833
Before this commit dj_probe would exit with an error if the initial
logi_dj_recv_query_paired_devices fails. The initial call may fail
when the receiver is connected through a kvm and the focus is away.
When the call fails this causes 2 problems:
1) dj_probe calls logi_dj_recv_query_paired_devices after calling
hid_device_io_start() so a HID report may have been received in between
and our delayedwork_callback may be running. It seems that the initial
logi_dj_recv_query_paired_devices failure happening with some KVMs triggers
this exact scenario, causing the work-queue to run on free-ed memory,
leading to:
2) Even if we were to fix 1. by making sure the work is stopped before
failing probe, failing probe is the wrong thing to do, we have
logi_dj_recv_queue_unknown_work to deal with the initial
logi_dj_recv_query_paired_devices failure.
Rather then error-ing out of the probe, causing the receiver to not work at
all we should rely on this, so that the attached devices will get properly
enumerated once the KVM focus is switched back.
Cc: stable@vger.kernel.org Fixes: 74808f9115ce ("HID: logitech-dj: add support for non unifying receivers") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out the fault was caused by a bug in the HID Logitech driver,
which violates the requirement that every pathway calling
hid_hw_start() must also call hid_hw_stop(). This patch fixes the bug
by making sure the requirement is met.
The sony driver is not properly cleaning up from potential failures in
sony_input_configured. Currently it calls hid_hw_stop, while hid_connect
is still running. This is not a good idea, instead hid_hw_stop should
be moved to sony_probe. Similar changes were recently made to Logitech
drivers, which were also doing improper cleanup.
The syzbot fuzzer provoked a general protection fault in the
hid-prodikeys driver:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc5+ #28
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:pcmidi_submit_output_report drivers/hid/hid-prodikeys.c:300 [inline]
RIP: 0010:pcmidi_set_operational drivers/hid/hid-prodikeys.c:558 [inline]
RIP: 0010:pcmidi_snd_initialise drivers/hid/hid-prodikeys.c:686 [inline]
RIP: 0010:pk_probe+0xb51/0xfd0 drivers/hid/hid-prodikeys.c:836
Code: 0f 85 50 04 00 00 48 8b 04 24 4c 89 7d 10 48 8b 58 08 e8 b2 53 e4 fc
48 8b 54 24 20 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f
85 13 04 00 00 48 ba 00 00 00 00 00 fc ff df 49 8b
The problem is caused by the fact that pcmidi_get_output_report() will
return an error if the HID device doesn't provide the right sort of
output report, but pcmidi_set_operational() doesn't bother to check
the return code and assumes the function call always succeeds.
This patch adds the missing check and aborts the probe operation if
necessary.
Andrew Lunn says this should be handled another way.
Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.
This was originally landed in:
commit 10117450735c ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed9f69 ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.
There's a bug in skiboot that causes the OPAL_XIVE_ALLOCATE_IRQ call
to return the 32-bit value 0xffffffff when OPAL has run out of IRQs.
Unfortunatelty, OPAL return values are signed 64-bit entities and
errors are supposed to be negative. If that happens, the linux code
confusingly treats 0xffffffff as a valid IRQ number and panics at some
point.
A fix was recently merged in skiboot:
e97391ae2bb5 ("xive: fix return value of opal_xive_allocate_irq()")
but we need a workaround anyway to support older skiboots already
in the field.
Internally convert 0xffffffff to OPAL_RESOURCE which is the usual error
returned upon resource exhaustion.
[Why]
DRM private objects have no hw_done/flip_done fencing mechanism on their
own and cannot be used to sequence commits accordingly.
When issuing commits that don't touch the same set of hardware resources
like page-flips on different CRTCs we can run into the issue below
because of this:
1. Client requests non-blocking Commit #1, has a new dc_state #1,
state is swapped, commit tail is deferred to work queue
2. Client requests non-blocking Commit #2, has a new dc_state #2,
state is swapped, commit tail is deferred to work queue
3. Commit #2 work starts, commit tail finishes,
atomic state is cleared, dc_state #1 is freed
4. Commit #1 work starts,
commit tail encounters null pointer deref on dc_state #1
In order to change the DC state as in the private object we need to
ensure that we wait for all outstanding commits to finish and that
any other pending commits must wait for the current one to finish as
well.
We do this for MEDIUM and FULL updates. But not for FAST updates, nor
would we want to since it would cause stuttering from the delays.
FAST updates that go through dm_determine_update_type_for_commit always
create a new dc_state and lock the DRM private object if there are
any changed planes.
We need the old state to validate, but we don't actually need the new
state here.
[How]
If the commit isn't a full update then the use after free can be
resolved by simply discarding the new state entirely and retaining
the existing one instead.
With this change the sequence above can be reexamined. Commit #2 will
still free Commit #1's reference, but before this happens we actually
added an additional reference as part of Commit #2.
If an update comes in during this that needs to change the dc_state
it will need to wait on Commit #1 and Commit #2 to finish. Then it'll
swap the state, finish the work in commit tail and drop the last
reference on Commit #2's dc_state.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204181 Fixes: 004b3938e637 ("drm/amd/display: Check scaling info when determing update type") Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: David Francis <david.francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
By passing through the dm_determine_update_type_for_commit for atomic
commits that can be done asynchronously we are incurring a
performance penalty by locking access to the global private object
and holding that access until the end of the programming sequence.
This is also allocating a new large dc_state on every access in addition
to retaining all the references on each stream and plane until the end
of the programming sequence.
[How]
Shift the determination for async update before validation. Return early
if it's going to be an async update.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: David Francis <david.francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
We previously allowed framebuffer swaps as async updates for cursor
planes but had to disable them due to a bug in DRM with async update
handling and incorrect ref counting. The check to block framebuffer
swaps has been added to DRM for a while now, so this check is redundant.
The real fix that allows this to properly in DRM has also finally been
merged and is getting backported into stable branches, so dropping
this now seems to be the right time to do so.
[How]
Drop the redundant check for old_fb != new_fb.
With the proper fix in DRM, this should also fix some cursor stuttering
issues with xf86-video-amdgpu since it double buffers the cursor.
IGT tests that swap framebuffers (-varying-size for example) should
also pass again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: David Francis <david.francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 36f1031c51a2 ("ibmvnic: Do not process reset during or after
device removal") made the change to exit reset if the driver has been
removed, but does not free reset work items of the adapter from queue.
Ensure all reset work items are freed when breaking out of the loop early.
Fixes: 36f1031c51a2 ("ibmnvic: Do not process reset during or after device removal”) Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Despite extensive testing of commit 885bd765963b ("phy: qcom-qmp: Correct
READY_STATUS poll break condition") I failed to conclude that the
PHYSTATUS bit of the PCS_STATUS register used in PCIe and USB3 falls as
the PHY gets ready. Similar to the prior bug with UFS the code will
generally get past the check before the transition and thereby
"succeed".
Correct the name of the register used PCIe and USB3 PHYs, replace
mask_pcs_ready with a constant expression depending on the type of the
PHY and check for the appropriate ready state.
Cc: stable@vger.kernel.org Cc: Vivek Gautam <vivek.gautam@codeaurora.org> Cc: Evan Green <evgreen@chromium.org> Cc: Niklas Cassel <niklas.cassel@linaro.org> Reported-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Fixes: 885bd765963b ("phy: qcom-qmp: Correct READY_STATUS poll break condition") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
readl_poll_timeout() calls usleep_range() to sleep between reads.
usleep_range() doesn't work efficiently for tiny values.
Raise the polling delay in qcom_qmp_phy_enable() to bring it in line
with the delay in qcom_qmp_phy_com_init().
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An earlier patch "CIFS: fix deadlock in cached root handling"
did not completely address the deadlock in open_shroot. This
patch addresses the deadlock.
In testing the recent patch:
smb3: improve handling of share deleted (and share recreated)
we were able to reproduce the open_shroot deadlock to one
of the target servers in unmount in a delete share scenario.
Fixes: 7e5a70ad88b1e ("CIFS: fix deadlock in cached root handling")
This is version 2 of this patch. An earlier version of this
patch "smb3: fix unmount hang in open_shroot" had a problem
found by Dan.
Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
Fix an overput in which filename_lookup() unconditionally drops a ref to
the filename it was given, but this isn't taken account of in the caller,
fs_lookup_param().
Addresses-Coverity-ID: 1443811 ("Use after free") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once upon a time, commit 2cac0c00a6cd ("ovl: get exclusive ownership on
upper/work dirs") in v4.13 added some sanity checks on overlayfs layers.
This change caused a docker regression. The root cause was mount leaks
by docker, which as far as I know, still exist.
To mitigate the regression, commit 85fdee1eef1a ("ovl: fix regression
caused by exclusive upper/work dir protection") in v4.14 turned the
mount errors into warnings for the default index=off configuration.
Recently, commit 146d62e5a586 ("ovl: detect overlapping layers") in
v5.2, re-introduced exclusive upper/work dir checks regardless of
index=off configuration.
This changes the status quo and mount leak related bug reports have
started to re-surface. Restore the status quo to fix the regressions.
To clarify, index=off does NOT relax overlapping layers check for this
ovelayfs mount. index=off only relaxes exclusive upper/work dir checks
with another overlayfs mount.
To cover the part of overlapping layers detection that used the
exclusive upper/work dir checks to detect overlap with self upper/work
dir, add a trap also on the work base dir.
Commit 24fe1b0efad4fcdd ("arm64: Remove unnecessary ISBs from
set_{pte,pmd,pud}") removed ISB instructions immediately following updates
to the page table, on the grounds that they are not required by the
architecture and a DSB alone is sufficient to ensure that subsequent data
accesses use the new translation:
DDI0487E_a, B2-128:
| ... no instruction that appears in program order after the DSB
| instruction can alter any state of the system or perform any part of
| its functionality until the DSB completes other than:
|
| * Being fetched from memory and decoded
| * Reading the general-purpose, SIMD and floating-point,
| Special-purpose, or System registers that are directly or indirectly
| read without causing side-effects.
However, the same document also states the following:
DDI0487E_a, B2-125:
| DMB and DSB instructions affect reads and writes to the memory system
| generated by Load/Store instructions and data or unified cache
| maintenance instructions being executed by the PE. Instruction fetches
| or accesses caused by a hardware translation table access are not
| explicit accesses.
which appears to claim that the DSB alone is insufficient. Unfortunately,
some CPU designers have followed the second clause above, whereas in Linux
we've been relying on the first. This means that our mapping sequence:
MOV X0, <valid pte>
STR X0, [Xptep] // Store new PTE to page table
DSB ISHST
LDR X1, [X2] // Translates using the new PTE
can actually raise a translation fault on the load instruction because the
translation can be performed speculatively before the page table update and
then marked as "faulting" by the CPU. For user PTEs, this is ok because we
can handle the spurious fault, but for kernel PTEs and intermediate table
entries this results in a panic().
Revert the offending commit to reintroduce the missing barriers.
Cc: <stable@vger.kernel.org> Fixes: 24fe1b0efad4fcdd ("arm64: Remove unnecessary ISBs from set_{pte,pmd,pud}") Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the conversion to lock-less dma-api call the
increase_address_space() function can be called without any
locking. Multiple CPUs could potentially race for increasing
the address space, leading to invalid domain->mode settings
and invalid page-tables. This has been happening in the wild
under high IO load and memory pressure.
Fix the race by locking this operation. The function is
called infrequently so that this does not introduce
a performance regression in the dma-api path again.
Reported-by: Qian Cai <cai@lca.pw> Fixes: 256e4621c21a ('iommu/amd: Make use of the generic IOVA allocator') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When devices are attached to the amd_iommu in a kdump kernel, the old device
table entries (DTEs), which were copied from the crashed kernel, will be
overwritten with a new domain number. When the new DTE is written, the IOMMU
is told to flush the DTE from its internal cache--but it is not told to flush
the translation cache entries for the old domain number.
Without this patch, AMD systems using the tg3 network driver fail when kdump
tries to save the vmcore to a network system, showing network timeouts and
(sometimes) IOMMU errors in the kernel log.
This patch will flush IOMMU translation cache entries for the old domain when
a DTE gets overwritten with a new domain number.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com> Fixes: 3ac3e5ee5ed5 ('iommu/amd: Copy old trans table from old kernel') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a request_key authentication token key gets revoked, there's a window in
which request_key_auth_describe() can see it with a NULL payload - but it
makes no check for this and something like the following oops may occur:
The commit 20c169aceb45 ("dmaengine: rcar-dmac: clear pertinence
number of channels") forgets to clear the last channel by
DMACHCLR in rcar_dmac_init() (and doesn't need to clear the first
channel) if iommu is mapped to the device. So, this patch fixes it
by using "channels_mask" bitfield.
Note that the hardware and driver don't support more than 32 bits
in DMACHCLR register anyway, so this patch should reject more than
32 channels in rcar_dmac_parse_of().
For the Spreadtrum DMA link-list mode, when the DMA engine got a slave
hardware request, which will trigger the DMA engine to load the DMA
configuration from the link-list memory automatically. But before the
slave hardware request, the slave will get an incorrect residue due
to the first node used to trigger the link-list was configured as the
last source address and destination address.
Thus we should make sure the first node was configured the start source
address and destination address, which can fix this issue.
Global pages support is removed from VT-d spec 3.0. Since global pages G
flag only affects first-level paging structures and because DMA request
with PASID are only supported by VT-d spec. 3.0 and onward, we can
safely remove global pages support.
For kernel shared virtual address IOTLB invalidation, PASID
granularity and page selective within PASID will be used. There is
no global granularity supported. Without this fix, IOTLB invalidation
will cause invalid descriptor error in the queued invalidation (QI)
interface.
Fixes: 1c4f88b7f1f9 ("iommu/vt-d: Shared virtual address in scalable mode") Reported-by: Sanjay K Kumar <sanjay.k.kumar@intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the 'start' parameter is >= 0xFF000000 on 32-bit
systems, or >= 0xFFFFFFFF'FF000000 on 64-bit systems,
fill_gva_list() gets into an infinite loop.
With such inputs, 'cur' overflows after adding HV_TLB_FLUSH_UNIT
and always compares as less than end. Memory is filled with
guest virtual addresses until the system crashes.
Fix this by never incrementing 'cur' to be larger than 'end'.
Reported-by: Jong Hyun Park <park.jonghyun@yonsei.ac.kr> Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 2ffd9e33ce4a ("x86/hyper-v: Use hypercall for remote TLB flush") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Identical to __put_user(); the __get_user() argument evalution will too
leak UBSAN crud into the __uaccess_begin() / __uaccess_end() region.
While uncommon this was observed to happen for:
drivers/xen/gntdev.c: if (__get_user(old_status, batch->status[i]))
where UBSAN added array bound checking.
This complements commit:
6ae865615fc4 ("x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation")
If devm_request_irq() fails to disable all interrupts, no cleanup is
performed before retuning the error. To fix this issue, invoke
omap_dma_free() to do the cleanup.
In ti_dra7_xbar_probe(), 'rsv_events' is allocated through kcalloc(). Then
of_property_read_u32_array() is invoked to search for the property.
However, if this process fails, 'rsv_events' is not deallocated, leading to
a memory leak bug. To fix this issue, free 'rsv_events' before returning
the error.
Currently there are two nodes named "regulator1" in the Draak DTS: a
3.3V regulator for the eMMC and the LVDS decoder, and a 12V regulator
for the backlight. This causes the former to be overwritten by the
latter.
Fix this by renaming all regulators with numerical suffixes to use named
suffixes, which are less likely to conflict.
In commit 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.
Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.
The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.
Issue was observed on older kernels (4.14) where no such logic exists.
Fixes: 4c83f170b3ac ("net: aquantia: link status irq handling") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Reported-by: Michael Symolkin <Michael.Symolkin@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.
Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0
Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some case C1% will be wrong value, when platform doesn't have MSR for
C1 residency.
For example:
Core CPU CPU%c1
- - 100.00
0 0 100.00
0 2 100.00
1 1 100.00
1 3 100.00
But adding Busy% will fix this
Core CPU Busy% CPU%c1
- - 99.77 0.23
0 0 99.77 0.23
0 2 99.77 0.23
1 1 99.77 0.23
1 3 99.77 0.23
This issue can be reproduced on most of the recent systems including
Broadwell, Skylake and later.
This is because if we don't select Busy% or Avg_MHz or Bzy_MHz then
mperf value will not be read from MSR, so it will be 0. But this
is required for C1% calculation when MSR for C1 residency is not present.
Same is true for C3, C6 and C7 column selection.
So add another define DO_BIC_READ(), which doesn't depend on user
column selection and use for mperf, C3, C6 and C7 related counters.
So when there is no platform support for C1 residency counters,
we still read these counters, if the CPU has support and user selected
display of CPU%c1.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
turbostat could be terminated by general protection fault on some latest
hardwares which (for example) support 9 levels of C-states and show 18
"tADDED" lines. That bloats the total output and finally causes buffer
overrun. So let's extend the buffer to avoid this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the error return path does not close the file fp and leaks
a file descriptor. Fix this by closing the file.
Fixes: 5ea7647b333f ("tools/power turbostat: Warn on bad ACPI LPIT data") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The -w argument in x86_energy_perf_policy currently triggers an
unconditional segfault.
This is because the argument string reads: "+a:c:dD:E:e:f:m:M:rt:u:vw" and
yet the argument handler expects an argument.
When parse_optarg_string is called with a null argument, we then proceed to
crash in strncmp, not horribly friendly.
The man page describes -w as taking an argument, the long form
(--hwp-window) is correctly marked as taking a required argument, and the
code expects it.
As such, this patch simply marks the short form (-w) as requiring an
argument.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
x86_energy_perf_policy first uses __get_cpuid() to check the maximum
CPUID level and exits if it is too low. It then assumes that later
calls will succeed (which I think is architecturally guaranteed). It
also assumes that CPUID works at all (which is not guaranteed on
x86_32).
If optimisations are enabled, gcc warns about potentially
uninitialized variables. Fix this by adding an exit-on-error after
every call to __get_cpuid() instead of just checking the maximum
level.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Quoting from mt8183 datasheet, the number of transfers to be
transferred in one transaction should be set to bigger than 1,
so we should forbid zero-length transfer and update functionality.
Reported-by: Alexandru M Stan <amstan@chromium.org> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Qii Wang <qii.wang@mediatek.com>
[wsa: shortened commit message a little] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver does not support the SMBUS Quick command so remove the
flag that indicates that level of support.
By default the i2c_detect tool uses the quick command to try and
detect devices at some bus addresses. If the quick command is used
then we will not detect the device, even though it is present.
Fixes: e6e5dd3566e0 (i2c: iproc: Add Broadcom iProc I2C Driver) Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When counting dispatched micro-ops with cnt_ctl=1, in order to prevent
sample bias, IBS hardware preloads the least significant 7 bits of
current count (IbsOpCurCnt) with random values, such that, after the
interrupt is handled and counting resumes, the next sample taken
will be slightly perturbed.
The current count bitfield is in the IBS execution control h/w register,
alongside the maximum count field.
Currently, the IBS driver writes that register with the maximum count,
leaving zeroes to fill the current count field, thereby overwriting
the random bits the hardware preloaded for itself.
Fix the driver to actually retain and carry those random bits from the
read of the IBS control register, through to its write, instead of
overwriting the lower current count bits with zeroes.
Tested with:
perf record -c 100001 -e ibs_op/cnt_ctl=1/pp -a -C 0 taskset -c 0 <workload>
Machines prior to family 10h Rev. C don't have the RDWROPCNT capability,
and have the IbsOpCurCnt bitfield reserved, so this patch shouldn't
affect their operation.
It is unknown why commit db98c5faf8cb ("perf/x86: Implement 64-bit
counter support for IBS") ignored the lower 4 bits of the IbsOpCurCnt
field; the number of preloaded random bits has always been 7, AFAICT.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: "Arnaldo Carvalho de Melo" <acme@kernel.org> Cc: <x86@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Borislav Petkov" <bp@alien8.de> Cc: Stephane Eranian <eranian@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: "Namhyung Kim" <namhyung@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20190826195730.30614-1-kim.phillips@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure interrupt handler i2c_dw_irq_handler_slave() has finished
before clearing the the dev->slave pointer in i2c_dw_unreg_slave().
There is possibility for a race if i2c_dw_irq_handler_slave() is running
on another CPU while clearing the dev->slave pointer.
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com> Reported-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
pfn_valid can be wrong when parsing a invalid pfn whose phys address
exceeds BITS_PER_LONG as the MSB will be trimed when shifted.
The issue originally arise from bellowing call stack, which corresponding to
an access of the /proc/kpageflags from userspace with a invalid pfn parameter
and leads to kernel panic.
[46886.723249] c7 [<c031ff98>] (stable_page_flags) from [<c03203f8>]
[46886.723264] c7 [<c0320368>] (kpageflags_read) from [<c0312030>]
[46886.723280] c7 [<c0311fb0>] (proc_reg_read) from [<c02a6e6c>]
[46886.723290] c7 [<c02a6e24>] (__vfs_read) from [<c02a7018>]
[46886.723301] c7 [<c02a6f74>] (vfs_read) from [<c02a778c>]
[46886.723315] c7 [<c02a770c>] (SyS_pread64) from [<c0108620>]
(ret_fast_syscall+0x0/0x28)
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, various virtual memory areas of Linux RISC-V are organized
in increasing order of their virtual addresses is as follows:
1. User space area (This is lowest area and starts at 0x0)
2. FIXMAP area
3. VMALLOC area
4. Kernel area (This is highest area and starts at PAGE_OFFSET)
The maximum size of user space aread is represented by TASK_SIZE.
On RV32 systems, TASK_SIZE is defined as VMALLOC_START which causes the
user space area to overlap the FIXMAP area. This allows user space apps
to potentially corrupt the FIXMAP area and kernel OF APIs will crash
whenever they access corrupted FDT in the FIXMAP area.
On RV64 systems, TASK_SIZE is set to fixed 256GB and no other areas
happen to overlap so we don't see any FIXMAP area corruptions.
This patch fixes FIXMAP area corruption on RV32 systems by setting
TASK_SIZE to FIXADDR_START. We also move FIXADDR_TOP, FIXADDR_SIZE,
and FIXADDR_START defines to asm/pgtable.h so that we can avoid cyclic
header includes.
Signed-off-by: Anup Patel <anup.patel@wdc.com> Tested-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Falcon microcontroller that runs the XUSB firmware and which is
responsible for exposing the XHCI interface can address only 40 bits of
memory. Typically that's not a problem because Tegra devices don't have
enough system memory to exceed those 40 bits.
However, if the ARM SMMU is enable on Tegra186 and later, the addresses
passed to the XUSB controller can be anywhere in the 48-bit IOV address
space of the ARM SMMU. Since the DMA/IOMMU API starts allocating from
the top of the IOVA space, the Falcon microcontroller is not able to
load the firmware successfully.
Fix this by setting the DMA mask to 40 bits, which will force the DMA
API to map the buffer for the firmware to an IOVA that is addressable by
the Falcon.
This happens to work because crypto_sync_skcipher is a trivial wrapper
around crypto_skcipher: &tfm->base is still 0 and crypto_free_skcipher()
handles that. Let's not rely on the layout of crypto_sync_skcipher.
This bug is found by a static analysis tool STCheck written by us.
It's safer to zero out the password so that it can never be disclosed.
Fixes: 0c219f5799c7 ("cifs: set domainName when a domain-key is used in multiuser") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we use a domain-key to authenticate using multiuser we must also set
the domainnmame for the new volume as it will be used and passed to the server
in the NTLMSSP Domain-name.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Looking at the implementation of get_symbol_pos(), it returns the
lowest index for aliasing symbols. In this case, it return 0.
But kallsyms_lookup_size_offset() considers 0 as a failure, which
is obviously wrong (there is definitely a valid symbol living there).
In turn, the kprobe blacklisting stops abruptly, hence the original
error.
A CONFIG_KALLSYMS_ALL kernel wouldn't fail as there is always
some random symbols at the beginning of this array, which are never
looked up via kallsyms_lookup_size_offset.
Fix it by considering that get_symbol_pos() is always successful
(which is consistent with the other uses of this function).
Fixes: ffc5089196446 ("[PATCH] Create kallsyms_lookup_size_offset()") Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The find_pattern() debug output was printing the 'skip' character.
This can be a NULL-byte and messes up further pr_debug() output.
Output without the fix:
kernel: nf_conntrack_ftp: Pattern matches!
kernel: nf_conntrack_ftp: Skipped up to `<7>nf_conntrack_ftp: find_pattern `PORT': dlen = 8
kernel: nf_conntrack_ftp: find_pattern `EPRT': dlen = 8
Output with the fix:
kernel: nf_conntrack_ftp: Pattern matches!
kernel: nf_conntrack_ftp: Skipped up to 0x0 delimiter!
kernel: nf_conntrack_ftp: Match succeeded!
kernel: nf_conntrack_ftp: conntrack_ftp: match `172,17,0,100,200,207' (20 bytes at 4150681645)
kernel: nf_conntrack_ftp: find_pattern `PORT': dlen = 8
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Simplify the check in physdev_mt_check() to emit an error message
only when passed an invalid chain (ie, NF_INET_LOCAL_OUT).
This avoids cluttering up the log with errors against valid rules.
For large/heavily modified rulesets, current behavior can quickly
overwhelm the ring buffer, because this function gets called on
every change, regardless of the rule that was changed.
If the client attempts to read a page, but the read fails due to some
spurious error (e.g. an ACCESS error or a timeout, ...) then we need
to allow other processes to retry.
Also try to report errors correctly when doing a synchronous readpage.
Rahul Tanwar reported the following bug on DT systems:
> 'ioapic_dynirq_base' contains the virtual IRQ base number. Presently, it is
> updated to the end of hardware IRQ numbers but this is done only when IOAPIC
> configuration type is IOAPIC_DOMAIN_LEGACY or IOAPIC_DOMAIN_STRICT. There is
> a third type IOAPIC_DOMAIN_DYNAMIC which applies when IOAPIC configuration
> comes from devicetree.
>
> See dtb_add_ioapic() in arch/x86/kernel/devicetree.c
>
> In case of IOAPIC_DOMAIN_DYNAMIC (DT/OF based system), 'ioapic_dynirq_base'
> remains to zero initialized value. This means that for OF based systems,
> virtual IRQ base will get set to zero.
Such systems will very likely not even boot.
For DT enabled machines ioapic_dynirq_base is irrelevant and not
updated, so simply map the IRQ base 1:1 instead.
get_registers() blindly copies the memory written to by the
usb_control_msg() call even if the underlying urb failed.
This could lead to junk register values being read by the driver, since
some indirect callers of get_registers() ignore the return values. One
example is:
ocp_read_dword() ignores the return value of generic_ocp_read(), which
calls get_registers().
So, emulate PCI "Master Abort" behavior by setting the buffer to all
0xFFs when usb_control_msg() fails.
This patch is copied from the r8152 driver (v2.12.0) published by
Realtek (www.realtek.com).
Signed-off-by: Prashant Malani <pmalani@chromium.org> Acked-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because on big-endian machines casts from __u32 to __u16 are
generated by referencing the respective variable as __u16 with an offset
of 2 (as opposed to 0 on little-endian machines).
The verifier already has all the infrastructure in place to allow such
accesses, it's just that they are not explicitly enabled for
eth_protocol field. Enable them for eth_protocol field by using
bpf_ctx_range instead of offsetof.
Ditto for ip_protocol, bind_inany and len, since they already allow
narrowing, and the same problem can arise when working with them.
Call to bpf_prog_put(), with help of call_rcu(), queues an RCU-callback to
free the program once a grace period has elapsed. The callback can run
together with new RCU readers that started after the last grace period.
New RCU readers can potentially see the "old" to-be-freed or already-freed
pointer to the program object before the RCU update-side NULLs it.
Reorder the operations so that the RCU update-side resets the protected
pointer before the end of the grace period after which the program will be
freed.
Fixes: d58e468b1112 ("flow_dissector: implements flow dissector BPF hook") Reported-by: Lorenz Bauer <lmb@cloudflare.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Acked-by: Petar Penkov <ppenkov@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Multiple batadv_ogm2_packet can be stored in an skbuff. The functions
batadv_v_ogm_send_to_if() uses batadv_v_ogm_aggr_packet() to check if there
is another additional batadv_ogm2_packet in the skb or not before they
continue processing the packet.
The length for such an OGM2 is BATADV_OGM2_HLEN +
batadv_ogm2_packet->tvlv_len. The check must first check that at least
BATADV_OGM2_HLEN bytes are available before it accesses tvlv_len (which is
part of the header. Otherwise it might try read outside of the currently
available skbuff to get the content of tvlv_len.
Fixes: 9323158ef9f4 ("batman-adv: OGMv2 - implement originators logic") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
A timing hazard exists when an early fork/exec thread begins
exiting and sets its mm pointer to NULL while a separate core
tries to update the section information.
This commit ensures that the mm pointer is not NULL before
setting its section parameters. The arguments provided by
commit 11ce4b33aedc ("ARM: 8672/1: mm: remove tasklist locking
from update_sections_early()") are equally valid for not
requiring grabbing the task_lock around this check.
Fixes: 08925c2f124f ("ARM: 8464/1: Update all mm structures with section adjustments") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Laura Abbott <labbott@redhat.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Rob Herring <robh@kernel.org> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must make sure our scatterlist segments are not too big, otherwise
we might see swiotlb failures (happens with sev, also reproducable with
swiotlb=force).
When refactoring port lookup for DSS outputs, commit d17eb4537a7e
("drm/omap: Factor out common init/cleanup code for output devices")
incorrectly hardcoded usage of DT port 0. This breaks operation for SDI
(which uses the DT port 1) and DPI outputs other than DPI0 (which are
not used in mainline DT sources).
Fix this by using the port number from the output omap_dss_device
of_ports field.
Fixes: d17eb4537a7e ("drm/omap: Factor out common init/cleanup code for output devices") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190821183226.13784-1-laurent.pinchart@ideasonboard.com Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Sasha Levin <sashal@kernel.org>
If qed_mcp_send_drv_version() fails, no cleanup is executed, leading to
memory leaks. To fix this issue, introduce the label 'err4' to perform the
cleanup work before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
# sysctl cannot stat /proc/sys/net/core/bpf_jit_enable No such file or directory
cannot: stat_/proc/sys/net/core/bpf_jit_enable #
# sysctl cannot stat /proc/sys/net/core/bpf_jit_harden No such file or directory
cannot: stat_/proc/sys/net/core/bpf_jit_harden #
Rework to enable CONFIG_BPF_JIT to solve "No such file or directory"
Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
test_cgroup_storage fails on s390 with an assertion failure: packets are
dropped when they shouldn't. The problem is that BPF_DW packet count is
accessed as BPF_W with an offset of 0, which is not correct on
big-endian machines.
Since the point of this test is not to verify narrow loads/stores,
simply use BPF_DW when working with packet counts.
Fixes: 68cfa3ac6b8d ("selftests/bpf: add a cgroup storage test") Fixes: 919646d2a3a9 ("selftests/bpf: extend the storage test to test per-cpu cgroup storage") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialise the result count to 0 rather than initialising it to the
argument count. The reason is that we want to ensure we record the
I/O stats correctly in the case where an error is returned (for
instance in the layoutstats).
Currently, we are translating RPC level errors such as timeouts,
as well as interrupts etc into EOPENSTALE, which forces a single
replay of the open attempt. What we actually want to do is
force the replay only in the cases where the returned error
indicates that the file may have changed on the server.
So the fix is to spell out the exact set of errors where we want
to return EOPENSTALE.
Trying to append nfacct related rules results in an unhelpful message.
Although it is suggested to look for more information in dmesg, nothing
can be found there.
# iptables -A <chain> -m nfacct --nfacct-name <acct-object>
iptables: Invalid argument. Run `dmesg' for more information.
This patch fixes the memory misalignment by enforcing 8-byte alignment
within the struct's first revision. This solution is often used in many
other uapi netfilter headers.
projects / users / dwmw2 / linux.git / log