It seems Clang can in some cases turn on stack protection by default, which
doesn't work with BPF. This was reported once before[0], but it seems the
flag to explicitly turn off the stack protector wasn't added to the
Makefile, so do that now.
The symptom of this is compile errors like the following:
error: <unknown>:0:0: in function bpf_prog1 i32 (%struct.__sk_buff*): A call to built-in function '__stack_chk_fail' is not supported.
When we fail to allocate string for journal device name we jump to
'error' label which tries to unlock reiserfs write lock which is not
held. Jump to 'error_unlocked' instead.
Fixes: f32485be8397 ("reiserfs: delay reiserfs lock until journal initialization") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with Clang + -Wtautological-constant-compare, several of
the ivtv and cx18 drivers warn along the lines of:
drivers/media/pci/cx18/cx18-driver.c:1005:21: warning: converting the
result of '<<' to a boolean always evaluates to true
[-Wtautological-constant-compare]
cx18_call_hw(cx, CX18_HW_GPIO_RESET_CTRL,
^
drivers/media/pci/cx18/cx18-cards.h:18:37: note: expanded from macro
'CX18_HW_GPIO_RESET_CTRL'
#define CX18_HW_GPIO_RESET_CTRL (1 << 6)
^
1 warning generated.
This warning happens because the shift operation is implicitly converted
to a boolean in v4l2_device_mask_call_all before being negated. This can
be solved by just comparing the mask result to 0 explicitly so that
there is no boolean conversion. The ultimate goal is to enable
-Wtautological-compare globally because there are several subwarnings
that would be helpful to have.
For visual consistency and avoidance of these warnings in the future,
all of the implicitly boolean conversions in the v4l2_device macros
are converted to explicit ones as well.
The SO_TXTIME test depends on accurate timers. In some virtualized
environments the test has been reported to be flaky. This is easily
reproduced by disabling kvm acceleration in Qemu.
Allow greater variance in a run and retry to further reduce flakiness.
Observed errors are one of two kinds: either the packet arrives too
early or late at recv(), or it was dropped in the qdisc itself and the
recv() call times out.
In the latter case, the qdisc queues a notification to the error
queue of the send socket. Also explicitly report this cause.
On Asus UX434DA (AMD Ryzen7 3700U) and Asus X512DK (AMD Ryzen5 3500U), the
XHCI controller fails to resume from runtime suspend or s2idle, and USB
becomes unusable from that point.
xhci_hcd 0000:03:00.4: Refused to change power state, currently in D3
xhci_hcd 0000:03:00.4: enabling device (0000 -> 0002)
xhci_hcd 0000:03:00.4: WARN: xHC restore state timeout
xhci_hcd 0000:03:00.4: PCI post-resume error -110!
xhci_hcd 0000:03:00.4: HC died; cleaning up
During suspend, a transition to D3cold is attempted, however the affected
platforms do not seem to cut the power to the PCI device when in this
state, so the device stays in D3hot.
Upon resume, the D3hot-to-D0 transition is successful only if the D3 delay
is increased to 20ms. The transition failure does not appear to be
detectable as a CRS condition. Add a PCI quirk to increase the delay on the
affected hardware.
Separate the D3 delay increase functionality out of quirk_radeon_pm() into
its own function so that it can be shared with other quirks, including the
AMD Ryzen XHCI quirk that will be introduced in a followup commit.
Tweak the function name and message to indicate more clearly that the delay
relates to a D3hot-to-D0 transition.
Link: https://lore.kernel.org/r/20191127053836.31624-1-drake@endlessm.com Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The AVerMedia CE310B is a simple composite + S-Video + stereo audio
capture card, and uses only the CX23888 to perform all of these
functions.
I've tested both video inputs and the audio interface and confirmed that
they're all working. However, there are some issues:
* Sometimes when I switch inputs the video signal turns black and can't
be recovered until the system is rebooted. I haven't been able to
determine the cause of this behavior, nor have I found a solution to
fix it or any workarounds other than rebooting.
* The card sometimes seems to have trouble syncing to the video signal,
and some of the VBI data appears as noise at the top of the frame, but
I assume that to be a result of my very noisy RF environment and the
card's unshielded input traces rather than a configuration issue.
Previously quirk_paxc_bridge() was applied when the iproc driver was
built-in, but not when it was compiled as a module.
This happened because it was under #ifdef CONFIG_PCIE_IPROC_PLATFORM:
PCIE_IPROC_PLATFORM=y causes CONFIG_PCIE_IPROC_PLATFORM to be defined, but
PCIE_IPROC_PLATFORM=m causes CONFIG_PCIE_IPROC_PLATFORM_MODULE to be
defined.
Move quirk_paxc_bridge() to pcie-iproc.c and drop the #ifdef so the quirk
is always applied, whether iproc is built-in or a module.
[bhelgaas: commit log, move to pcie-iproc.c, not pcie-iproc-platform.c] Link: https://lore.kernel.org/r/20191211174511.89713-1-wei.liu@kernel.org Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
process_buffer_measurement() may be called prior to IMA being
initialized (for instance, when the IMA hook is called when
a key is added to the .builtin_trusted_keys keyring), which
would result in a kernel panic.
This patch adds the check in process_buffer_measurement()
to return immediately if IMA is not initialized yet.
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Few options KALLSYMS_ALL, SCSI, PM_DEVFREQ and mutex/spinlock debugging
were removed with savedefconfig because they were selected by other
options. However these are user-visible options and they might not be
selected in the future. Exactly this happened with commit 0e4a459f56c3
("tracing: Remove unnecessary DEBUG_FS dependency") removing the
dependency between DEBUG_FS and TRACING.
To avoid losing these options in the future, explicitly mention them in
defconfig.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the clk_hw based API returns an error, trying to return the clk from
hw will end up in a NULL pointer dereference. So adding the to_clk
checker and using it inside every clk based macro helper we handle that
case correctly.
This to_clk is also temporary and will go away along with the clk based
macro helpers once there is no user that need them anymore.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
cpumask_weight() in padata_cpu_hash() returns 0 because the mask has no
CPUs. The problem is __padata_remove_cpu() checks for valid masks too
early and so doesn't mark the instance PADATA_INVALID as expected, which
would have made padata_do_parallel() return error before doing the
division.
Fix by introducing a second padata CPU hotplug state before
CPUHP_BRINGUP_CPU so that __padata_remove_cpu() sees the online mask
without @cpu. No need for the second argument to padata_replace() since
@cpu is now already missing from the online mask.
Fixes: 33e54450683c ("padata: Handle empty padata cpumasks") Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org> Signed-off-by: Paolo Pisati <p.pisati@gmail.com> Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4efe ("enetc: add support Credit Based Shaper(CBS) for hardware offload") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix avc_insert() to call avc_node_kill() if we've already allocated
an AVC node and the code fails to insert the node in the cache.
Fixes: fa1aa143ac4a ("selinux: extended permissions for ioctls") Reported-by: rsiddoji@codeaurora.org Suggested-by: Stephen Smalley <sds@tycho.nsa.gov> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The static OPPs aren't getting freed properly, if errors occur while
adding them. Fix that by calling _put_opp_list_kref() and putting their
reference on failures.
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the Performance Monitoring Unit (PMU) device tree node to the H5
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core.
As with the A64, the interrupt numbers from the manual were wrong (off
by 4), the actual SPI IDs have been gathered in U-Boot, and were
verified with perf in Linux.
Tested with perf record and taskset on an OrangePi PC2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on a Pine H64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Convert cpu_to_le16(le16_to_cpu(frame->datalen) + len) to
use le16_add_cpu(), which is more concise and does the same thing.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Qiang Zhao points out that these offsets get written to 16-bit
registers, and there are some QE platforms with more than 64K
muram. So it is possible that qe_muram_alloc() gives us an allocation
that can't actually be used by the hardware, so detect and reject
that.
Reported-by: Qiang Zhao <qiang.zhao@nxp.com> Reviewed-by: Timur Tabi <timur@kernel.org> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.
This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.
Fixes: a13eaf02e2d6 ("regulator: rk808: make better use of the gpiod API") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing code uses two handlers for a shared edge-based MSI interrupts.
In corner cases, interrupts are lost, leading to IPC timeouts. Those
timeouts do not appear in legacy mode.
This patch merges the two handlers and threads into a single one, and
simplifies the mask/unmask operations by using a single top-level mask
(Global Interrupt Enable). The handler only checks for interrupt
sources using the Global Interrupt Status (GIS) field, and all the
actual work happens in the thread. This also enables us to remove the
use of spin locks. Stream events are prioritized over IPC ones.
This patch was tested with HDaudio and SoundWire platforms, and all
known IPC timeout issues are solved in MSI mode. The
SoundWire-specific patches will be provided in follow-up patches,
where the SoundWire interrupts are handled in the same thread as IPC
and stream interrupts.
This is because list_for_each_entry_rcu(modules) is called
without rcu_read_lock(). This is safe because the module_mutex
is locked.
Pass lockdep_is_held(&module_mutex) to the list_for_each_entry_rcu()
to suppress this warning, This also fixes similar issue in
mod_find() and each_symbol_section().
Although it appeared to follow logically from the bindings, apparently
the thermal framework can't properly cope with a single cooling device
being shared between multiple maps. The CPU zone is probably easier to
overheat, so remove the references to the (optional) fan from the GPU
cooling zone to avoid things getting confused. Hopefully GPU-intensive
tasks will leak enough heat across to the CPU zone to still hit the
fan trips before reaching critical GPU temperatures.
Previously, there was an omap panel-dpi driver that would
read generic timings from the device tree and set the display
timing accordingly. This driver was removed so the screen
no longer functions. This patch modifies the panel-simple
file to setup the timings to the same values previously used.
Commit b0f3cd3191cd ("drm/amdgpu: remove unnecessary JPEG2.0 code from
VCN2.0") introduced a new clang warning in the vcn_v2_0_stop function:
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: warning: variable 'r'
is used uninitialized whenever 'while' loop exits because its condition
is false [-Wsometimes-uninitialized]
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1083:6: note: uninitialized use
occurs here
if (r)
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: note: remove the
condition if it is always true
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1072:7: note: initialize the
variable 'r' to silence this warning
int r;
^
= 0
1 warning generated.
To prevent warnings like this from happening in the future, make the
SOC15_WAIT_ON_RREG macro initialize its ret variable before the while
loop that can time out. This macro's return value is always checked so
it should set ret in both the success and fail path.
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f2f875 ("ath10k: support NET_DETECT WoWLAN feature") Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An old display with no audio may not have an EDID with a CEA block, or
it may simply be too old to support audio. This is not a driver error,
so don't flag it as such.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112140
References: ae2a3495973e ("drm/amd: be quiet when no SAD block is found") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Jean Delvare <jdelvare@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c: In function
'amdgpu_atombios_get_connector_info_from_object_table':
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:26: warning: variable
'grph_obj_num' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:13: warning: variable
'grph_obj_id' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:37: warning: variable
'con_obj_type' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:24: warning: variable
'con_obj_num' set but not used [-Wunused-but-set-variable]
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to have a synchronize_rcu before free'ing the sockhash because any
outstanding psock references will have a pointer to the map and when they
use it, this could trigger a use after free.
This is a sister fix for sockhash, following commit 2bb90e5cc90e ("bpf:
sockmap, synchronize_rcu before free'ing map") which addressed sockmap,
which comes from a manual audit.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200206111652.694507-3-jakub@cloudflare.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The sdma_queue_count increment should be done before
execute_queues_cpsch(), which calls pm_calc_rlib_size() where
sdma_queue_count is used to calculate whether over_subscription is
triggered.
With the previous code, when a SDMA queue is created,
compute_queue_count in pm_calc_rlib_size() is one more than the
actual compute queue number, because the queue_count has been
incremented while sdma_queue_count has not. This patch fixes that.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The DFS frequency table logic overwrites 'cfg' while detecting the
parent clk and then later on in clk_rcg2_dfs_populate_freq() we use that
same variable to figure out the mode of the clk, either MND or not. Add
a new variable to hold the parent clk bit so that 'cfg' is left
untouched for use later.
This fixes problems in detecting the supported frequencies for any clks
in DFS mode.
Fixes: cc4f6944d0e3 ("clk: qcom: Add support for RCG to register for DFS") Reported-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20200128193329.45635-1-sboyd@kernel.org Tested-by: Rajendra Nayak <rnayak@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5)
produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y,
which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency.
This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs
CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the
value of CONFIG_EFI is calculated.
When this happens, the has_changed flag should be set.
Currently, it takes the result from the last iteration. It should
accumulate all the results of the loop.
Fixes: 3b9a19e08960 ("kconfig: loop as long as we changed some symbols in randconfig") Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 478de3380c1c ("block, bfq: deschedule empty bfq_queues not
referred by any process") fixed commit 3726112ec731 ("block, bfq:
re-schedule empty queues if they deserve I/O plugging") by
descheduling an empty bfq_queue when it remains with not process
reference. Yet, this still left a case uncovered: an empty bfq_queue
with not process reference that remains in service. This happens for
an in-service sync bfq_queue that is deemed to deserve I/O-dispatch
plugging when it remains empty. Yet no new requests will arrive for
such a bfq_queue if no process sends requests to it any longer. Even
worse, the bfq_queue may happen to be prematurely freed while still in
service (because there may remain no reference to it any longer).
This commit solves this problem by preventing I/O dispatch from being
plugged for the in-service bfq_queue, if the latter has no process
reference (the bfq_queue is then prevented from remaining in service).
Fixes: 3726112ec731 ("block, bfq: re-schedule empty queues if they deserve I/O plugging") Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by: Patrick Dung <patdung100@gmail.com> Tested-by: Patrick Dung <patdung100@gmail.com> Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when an error code -EIO or -ENOSPC in the for-loop of
writeback_store the error code is being overwritten by a ret = len
assignment at the end of the function and the error codes are being
lost. Fix this by assigning ret = len at the start of the function and
remove the assignment from the end, hence allowing ret to be preserved
when error codes are assigned to it.
Addresses Coverity ("Unused value")
Link: http://lkml.kernel.org/r/20191128122958.178290-1-colin.king@canonical.com Fixes: a939888ec38b ("zram: support idle/huge page writeback") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For COW, btrfs expects pages dirty pages to have been through a few setup
steps. This includes reserving space for the new block allocations and marking
the range in the state tree for delayed allocation.
A few places outside btrfs will dirty pages directly, especially when unmapping
mmap'd pages. In order for these to properly go through COW, we run them
through a fixup worker to wait for stable pages, and do the delalloc prep.
87826df0ec36 added a window where the dirty pages were cleaned, but pending
more action from the fixup worker. We clear_page_dirty_for_io() before
we call into writepage, so the page is no longer dirty. The commit
changed it so now we leave the page clean between unlocking it here and
the fixup worker starting at some point in the future.
During this window, page migration can jump in and relocate the page. Once our
fixup work actually starts, it finds page->mapping is NULL and we end up
freeing the page without ever writing it.
This leads to crc errors and other exciting problems, since it screws up the
whole statemachine for waiting for ordered extents. The fix here is to keep
the page dirty while we're waiting for the fixup worker to get to work.
This is accomplished by returning -EAGAIN from btrfs_writepage_cow_fixup
if we queued the page up for fixup, which will cause the writepage
function to redirty the page.
Because we now expect the page to be dirty once it gets to the fixup
worker we must adjust the error cases to call clear_page_dirty_for_io()
on the page. That is the bulk of the patch, but it is not the fix, the
fix is the -EAGAIN from btrfs_writepage_cow_fixup. We cannot separate
these two changes out because the error conditions change with the new
expectations.
Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kzalloc fail, may cause trying to destroy the
workqueue from inside the workqueue.
If num_connections is m (2 < m), and NO.1 ~ NO.n
(1 < n < m) kzalloc are successful. The NO.(n + 1)
failed. Then, nbd_start_device will return ENOMEM
to nbd_start_device_ioctl, and nbd_start_device_ioctl
will return immediately without running flush_workqueue.
However, we still have n recv threads. If nbd_release
run first, recv threads may have to drop the last
config_refs and try to destroy the workqueue from
inside the workqueue.
To fix it, add a flush_workqueue in nbd_start_device.
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs") Signed-off-by: Sun Ke <sunke32@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the process of adding better error messages for sorting, I realized
that strsep was being used incorrectly and some of the error paths I
was expecting to be hit weren't and just fell through to the common
invalid key error case.
It also became obvious that for keyword assignments, it wasn't
necessary to save the full assignment and reparse it later, and having
a common empty-assignment check would also make more sense in terms of
error processing.
Change the code to fix these problems and simplify it for new error
message changes in a subsequent patch.
Link: http://lkml.kernel.org/r/1c3ef0b6655deaf345f6faee2584a0298ac2d743.1561743018.git.zanussi@kernel.org Fixes: e62347d24534 ("tracing: Add hist trigger support for user-defined sorting ('sort=' param)") Fixes: 7ef224d1d0e3 ("tracing: Add 'hist' event trigger command") Fixes: a4072fe85ba3 ("tracing: Add a clock attribute for hist triggers") Reported-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf67d ("drm/amd/display: DP Compliance 400.1.1 failure") Suggested-by: Louis Li <Ching-shih.Li@amd.com> Tested-by: Louis Li <Ching-shih.Li@amd.com> Cc: Wenjing Liu <Wenjing.Liu@amd.com> Cc: Hersen Wu <hersenxs.wu@amd.com> Cc: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Signed-off-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Merely enabling I2C and RTC selects REGMAP_I2C and REGMAP_SPI, even when
no driver needs it. While the former can be moduler, the latter cannot,
and thus becomes built-in.
Fix this by moving the select statements for REGMAP_I2C and REGMAP_SPI
from the RTC_I2C_AND_SPI helper to the individual drivers that depend on
it.
Note that the comment for RTC_I2C_AND_SPI refers to SND_SOC_I2C_AND_SPI
for more information, but the latter does not select REGMAP_{I2C,SPI}
itself, and defers that to the individual drivers, too.
Commit 852c8cbf34d3 ("selftests/kselftest/runner.sh: Add 45 second
timeout per test") adds support for a new per-test-directory "settings"
file. But this only works for tests not in a sub-subdirectories, e.g.
- tools/testing/selftests/rtc (rtc) is OK,
- tools/testing/selftests/net/mptcp (net/mptcp) is not.
We have to increase the timeout for net/mptcp tests which are not
upstreamed yet but this fix is valid for other tests if they need to add
a "settings" file, see the full list with:
tools/testing/selftests/*/*/**/Makefile
Note that this patch changes the text header message printed at the end
of the execution but this text is modified only for the tests that are
in sub-subdirectories, e.g.
ok 1 selftests: net/mptcp: mptcp_connect.sh
Before we had:
ok 1 selftests: mptcp: mptcp_connect.sh
But showing the full target name is probably better, just in case a
subsubdir has the same name as another one in another subdirectory.
Commit 262f2b53f679 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438 Fixes: 262f2b53f679 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()") Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
JBD2_REC_ERR flag used to indicate the errno has been updated when jbd2
aborted, and then __ext4_abort() and ext4_handle_error() can invoke
panic if ERRORS_PANIC is specified. But if the journal has been aborted
with zero errno, jbd2_journal_abort() didn't set this flag so we can
no longer panic. Fix this by always record the proper errno in the
journal superblock.
Fixes: 4327ba52afd03 ("ext4, jbd2: ensure entering into panic after recording an error in superblock") Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20191204124614.45424-3-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).
arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
undefined reference to `__start_ro_after_init'
linux/Makefile:1078: recipe for target 'vmlinux' failed
Fix the issue enabling kmemleak only on non XIP kernels.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Looking through old emails in my INBOX, I came across a patch from Luis
Henriques that attempted to fix a race of two stat tracers registering the
same stat trace (extremely unlikely, as this is done in the kernel, and
probably doesn't even exist). The submitted patch wasn't quite right as it
needed to deal with clean up a bit better (if two stat tracers were the
same, it would have the same files).
But to make the code cleaner, all we needed to do is to keep the
all_stat_sessions_mutex held for most of the registering function.
Link: http://lkml.kernel.org/r/1410299375-20068-1-git-send-email-luis.henriques@canonical.com Fixes: 002bb86d8d42f ("tracing/ftrace: separate events tracing and stats tracing engine") Reported-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
tracing_stat_init() was always returning '0', even on the error paths. It
now returns -ENODEV if tracing_init_dentry() fails or -ENOMEM if it fails
to created the 'trace_stat' debugfs directory.
Link: http://lkml.kernel.org/r/1410299381-20108-1-git-send-email-luis.henriques@canonical.com Fixes: ed6f1c996bfe4 ("tracing: Check return value of tracing_init_dentry()") Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[ Pulled from the archeological digging of my INBOX ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:
pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)
The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:
With zpci_disable() working, lockdep detected a potential deadlock
(lockdep output at the end).
The deadlock is between recovering a PCI function via the
/sys/bus/pci/devices/<dev>/recover
attribute vs powering it off via
/sys/bus/pci/slots/<slot>/power.
The fix is analogous to the changes in commit 0ee223b2e1f6 ("scsi: core:
Avoid that SCSI device removal through sysfs triggers a deadlock")
that fixed a potential deadlock on removing a SCSI device via sysfs.
[ 204.830107] ======================================================
[ 204.830109] WARNING: possible circular locking dependency detected
[ 204.830111] 5.5.0-rc2-06072-gbc03ecc9a672 #6 Tainted: G W
[ 204.830112] ------------------------------------------------------
[ 204.830113] bash/1034 is trying to acquire lock:
[ 204.830115] 0000000192a1a610 (kn->count#200){++++}, at: kernfs_remove_by_name_ns+0x5c/0xa8
[ 204.830122]
but task is already holding lock:
[ 204.830123] 00000000c16134a8 (pci_rescan_remove_lock){+.+.}, at: pci_stop_and_remove_bus_device_locked+0x26/0x48
[ 204.830128]
which lock already depends on the new lock.
When updating an LPI configuration, get_vlpi_map() may be passed a
irq_data structure relative to an ITS domain (the normal case) or one
that is relative to the core GICv3 domain in the case of a GICv4
doorbell.
In the latter case, special care must be take not to dereference
the irq_chip data as an its_dev structure, as that isn't what is
stored there. Instead, check *first* whether the IRQ is forwarded
to a vcpu, and only then try to obtain the vlpi mapping.
o call skb_reset_network_header() before hdlc->xmit()
o change skb proto to HDLC (0x0019) before hdlc->xmit()
o call dev_queue_xmit_nit() before hdlc->xmit()
This changes make it possible to trace (tcpdump) outgoing layer2
(ETH_P_HDLC) packets
Additionally call skb_reset_network_header() after each skb_push() /
skb_pull().
Signed-off-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is duplicated argument to && in function fsl_qdma_free_chan_resources,
which looks like a typo, pointer fsl_queue->desc_pool also needs NULL check,
fix it.
Detected with coccinelle.
A partition with Access Type 3 (rewritable) shall define a Freed
Space Bitmap or a Freed Space Table, see 2.3.3. All other partitions
shall not define a Freed Space Bitmap or a Freed Space Table.
Rewritable partitions are used on media that require some form of
preprocessing before re-writing data (for example legacy MO). Such
partitions shall use Access Type 3.
Overwritable partitions are used on media that do not require
preprocessing before overwriting data (for example: CD-RW, DVD-RW,
DVD+RW, DVD-RAM, BD-RE, HD DVD-Rewritable). Such partitions shall
use Access Type 4.
however older versions of the standard didn't have this wording and
there are tools out there that create UDF filesystems with rewritable
partitions but that don't contain a Freed Space Bitmap or a Freed Space
Table on media that does not require pre-processing before overwriting a
block. So instead of forcing media with rewritable partition read-only,
base this decision on presence of a Freed Space Bitmap or a Freed Space
Table.
Reported-by: Pali Rohár <pali.rohar@gmail.com> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Fixes: b085fbe2ef7f ("udf: Fix crash during mount") Link: https://lore.kernel.org/linux-fsdevel/20200112144735.hj2emsoy4uwsouxz@pali Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When checking whether the reported lfb_size makes sense, the height
* stride result is page-aligned before seeing whether it exceeds the
reported size.
This doesn't work if height * stride is not an exact number of pages.
For example, as reported in the kernel bugzilla below, an 800x600x32 EFI
framebuffer gets skipped because of this.
The parent clk for gmac clk ctrl has to be gmac_main_clk (125MHz) instead
of dpll_gmac_ck (1GHz). This is caused incorrect CPSW MDIO operation.
Hence, fix it.
Without any form of coordination, any case where multiple allocations
from the same mempool are needed at a time to make forward progress can
deadlock under memory pressure.
This is the case for struct bio_post_read_ctx, as one can be allocated
to decrypt a Merkle tree page during fsverity_verify_bio(), which itself
is running from a post-read callback for a data bio which has its own
struct bio_post_read_ctx.
Fix this by freeing the first bio_post_read_ctx before calling
fsverity_verify_bio(). This works because verity (if enabled) is always
the last post-read step.
This deadlock can be reproduced by trying to read from an encrypted
verity file after reducing NUM_PREALLOC_POST_READ_CTXS to 1 and patching
mempool_alloc() to pretend that pool->alloc() always fails.
Note that since NUM_PREALLOC_POST_READ_CTXS is actually 128, to actually
hit this bug in practice would require reading from lots of encrypted
verity files at the same time. But it's theoretically possible, as N
available objects isn't enough to guarantee forward progress when > N/2
threads each need 2 objects at a time.
If the journal is dirty when the filesystem is mounted, jbd2 will replay
the journal but the journal superblock will not be updated by
journal_reset() because JBD2_ABORT flag is still set (it was set in
journal_init_common()). This is problematic because when a new transaction
is then committed, it will be recorded in block 1 (journal->j_tail was set
to 1 in journal_reset()). If unclean shutdown happens again before the
journal superblock is updated, the new recorded transaction will not be
replayed during the next mount (because of stale sb->s_start and
sb->s_sequence values) which can lead to filesystem corruption.
Fixes: 85e0c4e89c1b ("jbd2: if the journal is aborted then don't allow update of the log tail") Signed-off-by: Kai Li <li.kai4@h3c.com> Link: https://lore.kernel.org/r/20200111022542.5008-1-li.kai4@h3c.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest. This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function. The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries. Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.
On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.
Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.
To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function. The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak") Fixes: 524a7f08983d ("clocksource/drivers/bcm2835_timer: Convert init function to return error") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
On chips with fewer FIFOs than endpoints (for example RK3288 which has 9
endpoints, but only 6 which are cabable of input), the DPTXFSIZN
registers above the FIFO count may return invalid values.
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.
To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sizeof is currently on args.src and args.dst and should be on
*args.src and *args.dst. Fortunately these sizes just so happen
to be the same size so it worked, however, this should be fixed
and it also cleans up static analysis warnings
Addresses-Coverity: ("sizeof not portable") Fixes: f268307ec7c7 ("nouveau: simplify nouveau_dmem_migrate_vma") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Why it does not work at the moment:
- num_chipselect sets the number of cs-gpios that are in the DT.
This comes from drivers/spi/spi.c
- num_chipselect gets set with devm_spi_register_controller, that is
called in drivers/spi/spi.c
- devm_spi_register_controller got called after num_chipselect has
been used.
How this commit fixes the issue:
- devm_spi_register_controller gets called before num_chipselect is
being used.
Fixes: c7a402599504 ("spi: lpspi: use the core way to implement cs-gpio function") Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Link: https://lore.kernel.org/r/20191204141312.1411251-1-philippe.schenker@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
kernel/irq/manage.c, 523:
synchronize_irq in disable_irq
drivers/uio/uio_dmem_genirq.c, 140:
disable_irq in uio_dmem_genirq_irqcontrol
drivers/uio/uio_dmem_genirq.c, 134:
_raw_spin_lock_irqsave in uio_dmem_genirq_irqcontrol
synchronize_irq() can sleep at runtime.
To fix this bug, disable_irq() is called without holding the spinlock.
This bug is found by a static analysis tool STCheck written by myself.
The compilation error is redeclaration showed as following:
In file included from ../../../include/linux/limits.h:6,
from /usr/include/x86_64-linux-gnu/bits/local_lim.h:38,
from /usr/include/x86_64-linux-gnu/bits/posix1_lim.h:161,
from /usr/include/limits.h:183,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/limits.h:194,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/syslimits.h:7,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/limits.h:34,
from ../../../include/linux/raid/pq.h:30,
from algos.c:14:
../../../include/linux/types.h:114:15: error: conflicting types for ‘int64_t’
typedef s64 int64_t;
^~~~~~~
In file included from /usr/include/stdint.h:34,
from /usr/lib/gcc/x86_64-linux-gnu/8/include/stdint.h:9,
from /usr/include/inttypes.h:27,
from ../../../include/linux/raid/pq.h:29,
from algos.c:14:
/usr/include/x86_64-linux-gnu/bits/stdint-intn.h:27:19: note: previous \
declaration of ‘int64_t’ was here
typedef __int64_t int64_t;
Fixes: 54d50897d544 ("linux/kernel.h: split *_MAX and *_MIN macros into <linux/limits.h>") Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IXP4xx driver was initializing the MDIO bus before even
probing, in the callbacks supposed to be used for setting up
the module itself, and with the side effect of trying to
register the MDIO bus as soon as this module was loaded or
compiled into the kernel whether the device was discovered
or not.
This does not work with multiplatform environments.
To get rid of this: set up the MDIO bus from the probe()
callback and remove it in the remove() callback. Rename
the probe() and remove() calls to reflect the most common
conventions.
Since there is a bit of checking for the ethernet feature
to be present in the MDIO registering function, making the
whole module not even be registered if we can't find an
MDIO bus, we need something similar: register the MDIO
bus when the corresponding ethernet is probed, and
return -EPROBE_DEFER on the other interfaces until this
happens. If no MDIO bus is present on any of the
registered interfaces we will eventually bail out.
None of the platforms I've seen has e.g. MDIO on EthB
and only uses EthC, there is always a Ethernet hardware
on the NPE (B, C) that has the MDIO bus, we just might
have to wait for it.
Fix a couple of issues with the way we map and copy the vendor string:
- we map only 2 bytes, which usually works since you get at least a
page, but if the vendor string happens to cross a page boundary,
a crash will result
- only call early_memunmap() if early_memremap() succeeded, or we will
call it with a NULL address which it doesn't like,
- while at it, switch to early_memremap_ro(), and array indexing rather
than pointer dereferencing to read the CHAR16 characters.
optimize_kprobe() and unoptimize_kprobe() cancels if a given kprobe
is on the optimizing_list or unoptimizing_list already. However, since
the following commit:
f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code")
modified the update timing of the KPROBE_FLAG_OPTIMIZED, it doesn't
work as expected anymore.
The optimized_kprobe could be in the following states:
- [optimizing]: Before inserting jump instruction
op.kp->flags has KPROBE_FLAG_OPTIMIZED and
op->list is not empty.
- [optimized]: jump inserted
op.kp->flags has KPROBE_FLAG_OPTIMIZED and
op->list is empty.
- [unoptimizing]: Before removing jump instruction (including unused
optprobe)
op.kp->flags has KPROBE_FLAG_OPTIMIZED and
op->list is not empty.
- [unoptimized]: jump removed
op.kp->flags doesn't have KPROBE_FLAG_OPTIMIZED and
op->list is empty.
Current code mis-expects [unoptimizing] state doesn't have
KPROBE_FLAG_OPTIMIZED, and that can cause incorrect results.
To fix this, introduce optprobe_queued_unopt() to distinguish [optimizing]
and [unoptimizing] states and fixes the logic in optimize_kprobe() and
unoptimize_kprobe().
[ mingo: Cleaned up the changelog and the code a bit. ]
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bristot@redhat.com Fixes: f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code") Link: https://lkml.kernel.org/r/157840814418.7181.13478003006386303481.stgit@devnote2 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when the low level driver notifies Pkey, GID, and port change
events they are notified to the registered handlers in the order they are
registered.
IB core and other ULPs such as IPoIB are interested in GID, LID, Pkey
change events.
Since all GID queries done by ULPs are serviced by IB core, and the IB
core deferes cache updates to a work queue, it is possible for other
clients to see stale cache data when they handle their own events.
For example, the below call tree shows how ipoib will call
rdma_query_gid() concurrently with the update to the cache sitting in the
WQ.
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/media/platform/sti/bdisp/bdisp-hw.c, 385:
msleep in bdisp_hw_reset
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 341:
bdisp_hw_reset in bdisp_device_run
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 317:
_raw_spin_lock_irqsave in bdisp_device_run
To fix this bug, msleep() is replaced with udelay().
This bug is found by a static analysis tool STCheck written by myself.
but those code is so old, and I have no clue how to de-couple it after
checking other locks in the splat. There is an onging effort to make all
printk() as deferred, so until that happens, workaround it for now as a
short-term fix.
raid_status() wasn't emitting rebuild flags on the table line properly
because the rdev number was not yet set properly; index raid component
devices array directly to solve.
Also fix wrong argument count on emitted table line caused by 1 too
many rebuild/write_mostly argument and consider any journal_(dev|mode)
pairs.
In __fpu__restore_sig(), fpu_fpregs_owner_ctx needs to be reset if the
FPU state was not fully restored. Otherwise the following may happen (on
the same CPU):
In the success case, fpu_fpregs_owner_ctx is set to the current task.
In the failure case, the FPU state might have been modified by loading
the init state.
In this case, fpu_fpregs_owner_ctx needs to be reset in order to ensure
that the FPU state of the following task is loaded from saved state (and
not skipped because it was the previous state).
Reset fpu_fpregs_owner_ctx after a failure during restore occurred, to
ensure that the FPU state for the next task is always loaded.
The problem was debugged-by Yu-cheng Yu <yu-cheng.yu@intel.com>.
[ bp: Massage commit message. ]
Fixes: 5f409e20b7945 ("x86/fpu: Defer FPU state load until return to userspace") Reported-by: Yu-cheng Yu <yu-cheng.yu@intel.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20191220195906.plk6kpmsrikvbcfn@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
PASID allocator uses IDR which is exclusive for the end of the
allocation range. There is no need to decrement pasid_max.
Fixes: af39507305fb ("iommu/vt-d: Apply global PASID in SVA") Reported-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
This fixes a potential hang when changing the GPU frequency at runtime.
On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:
1. Create a pci_dn structure for each of the VFs, and
2. Configure the PHB's internal BARs so the MMIO range for each VF
maps to a unique PE.
Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.
The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:
a) pcibios_setup_bridge() is not called again when VFs are activated, and
b) The pci_dev for VFs are created by generic code which runs after
pcibios_sriov_enable() is called.
The work around for this is a two step process:
1. A fixup in pcibios_add_device() is used to initialised the cached
pe_number in pci_dn, then
2. A bus notifier then adds the device to the IOMMU group for the PE
specified in pci_dn->pe_number.
A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.
We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:
1. We trip the WARN_ON() in the current fixup code, and
2. The EEH core clears pdn->pe_number when recovering a VF and
relies on the fixup to correctly re-set it.
The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.
The prescaler works as parent rate divided by (PRES + 1) (is_pres_direct == 1)
It does not work in the way of parent rate shifted to the right by (PRES + 1),
which means division by 2^(PRES + 1) (is_pres_direct == 0)
Thus is_pres_direct must be enabled for this SoC, to make the right computation.
This field was added in
commit 45b06682113b ("clk: at91: fix programmable clock for sama5d2")
SAM9X60 has the same field as SAMA5D2 in the PCK
The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.
Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.
projects / users / dwmw2 / linux.git / log