Introduce dev_busid, which exports the device-id associated with the
io-subchannel (and message-subchannel). The dev_busid indicates that of
the device which may be physically installed on the corrosponding
subchannel. The dev_busid value "none" indicates that the subchannel
is not valid, there is no I/O device currently associated with the
subchannel.
The dev_busid information would be helpful to write device-specific
udev-rules associated with the subchannel. The dev_busid interface would
be available even when the sch is not bound to any driver or if there is
no operational device connected on it. Hence this attribute can be used to
write udev-rules which are specific to the device associated with the
subchannel.
We update ctrl->queue_count and schedule another reconnect when io queue
count is zero.But we will never try to create any io queue in next reco-
nnection, because ctrl->queue_count already set to zero.We will end up
having an admin-only session in Live state, which is exactly what we try
to avoid in the original patch.
Update ctrl->queue_count after queue_count zero checking to fix it.
Signed-off-by: Ruozhu Li <liruozhu@huawei.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently iocharset=utf8 mount option is broken. To use UTF-8 as iocharset,
it is required to use utf8 mount option.
Fix iocharset=utf8 mount option to use be equivalent to the utf8 mount
option.
If UTF-8 as iocharset is used then s_nls_iocharset is set to NULL. So
simplify code around, remove s_utf8 field as to distinguish between UTF-8
and non-UTF-8 it is needed just to check if s_nls_iocharset is set to NULL
or not.
We were checking validity of LVID entries only when getting
implementation use information from LVID in udf_sb_lvidiu(). However if
the LVID is suitably corrupted, it can cause problems also to code such
as udf_count_free() which doesn't use udf_sb_lvidiu(). So check validity
of LVID already when loading it from the disk and just disable LVID
altogether when it is not valid.
Reported-by: syzbot+7fbfe5fed73ebb675748@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If __hrtimer_start_range_ns() is invoked with an already armed hrtimer then
the timer has to be canceled first and then added back. If the timer is the
first expiring timer then on removal the clockevent device is reprogrammed
to the next expiring timer to avoid that the pending expiry fires needlessly.
If the new expiry time ends up to be the first expiry again then the clock
event device has to reprogrammed again.
Avoid this by checking whether the timer is the first to expire and in that
case, keep the timer on the current CPU and delay the reprogramming up to
the point where the timer has been enqueued again.
We should not clear FLAGS_DMA_ACTIVE before omap_sham_update_dma_stop() is
done calling dma_unmap_sg(). We already clear FLAGS_DMA_ACTIVE at the
end of omap_sham_update_dma_stop().
The early clearing of FLAGS_DMA_ACTIVE is not causing issues as we do not
need to defer anything based on FLAGS_DMA_ACTIVE currently. So this can be
applied as clean-up.
Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Tero Kristo <kristo@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible for sched_getattr() to incorrectly report the state of
the reset_on_fork flag when called on a deadline task.
Indeed, if the flag was set on a deadline task using sched_setattr()
with flags (SCHED_FLAG_RESET_ON_FORK | SCHED_FLAG_KEEP_PARAMS), then
p->sched_reset_on_fork will be set, but __setscheduler() will bail out
early, which means that the dl_se->flags will not get updated by
__setscheduler_params()->__setparam_dl(). Consequently, if
sched_getattr() is then called on the task, __getparam_dl() will
override kattr.sched_flags with the now out-of-date copy in dl_se->flags
and report the stale value to userspace.
To fix this, make sure to only copy the flags that are relevant to
sched_deadline to and from the dl_se->flags field.
After calling dma_map_single(), we must also call dma_mapping_error().
This fixes the following warning when compiling with CONFIG_DMA_API_DEBUG:
[ 311.241478] WARNING: CPU: 0 PID: 428 at kernel/dma/debug.c:1027 check_unmap+0x79c/0x96c
[ 311.249547] DMA-API: mxs-dcp 2280000.crypto: device driver failed to check map error[device address=0x00000000860cb080] [size=32 bytes] [mapped as single]
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When this platform was relatively new in November 2011, with early BIOS
revisions, a reboot quirk was added in commit 6be30bb7d750 ("x86/reboot:
Blacklist Dell OptiPlex 990 known to require PCI reboot")
However, this quirk (and several others) are open-ended to all BIOS
versions and left no automatic expiry if/when the system BIOS fixed the
issue, meaning that nobody is likely to come along and re-test.
What is really problematic with using PCI reboot as this quirk does, is
that it causes this platform to do a full power down, wait one second,
and then power back on. This is less than ideal if one is using it for
boot testing and/or bisecting kernels when legacy rotating hard disks
are installed.
It was only by chance that the quirk was noticed in dmesg - and when
disabled it turned out that it wasn't required anymore (BIOS A24), and a
default reboot would work fine without the "harshness" of power cycling the
machine (and disks) down and up like the PCI reboot does.
Doing a bit more research, it seems that the "newest" BIOS for which the
issue was reported[1] was version A06, however Dell[2] seemed to suggest
only up to and including version A05, with the A06 having a large number of
fixes[3] listed.
As is typical with a new platform, the initial BIOS updates come frequently
and then taper off (and in this case, with a revival for CPU CVEs); a
search for O990-A<ver>.exe reveals the following dates:
A02 16 Mar 2011
A03 11 May 2011
A06 14 Sep 2011
A07 24 Oct 2011
A10 08 Dec 2011
A14 06 Sep 2012
A16 15 Oct 2012
A18 30 Sep 2013
A19 23 Sep 2015
A20 02 Jun 2017
A23 07 Mar 2018
A24 21 Aug 2018
While it's overkill to flash and test each of the above, it would seem
likely that the issue was contained within A0x BIOS versions, given the
dates above and the dates of issue reports[4] from distros. So rather than
just throw out the quirk entirely, limit the scope to just those early BIOS
versions, in case people are still running systems from 2011 with the
original as-shipped early A0x BIOS versions.
According to the datasheet, "Upon the completion of FW Download,
there is no need to write or reload FW.". Otherwise, it's possible
to cause unexpected behaviors. So, adds such a condition.
Fixes: 4ac8918f3a73 ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers") Cc: stable@vger.kernel.org # v3.17+ Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
It's no longer possible to create compressed inline extent after commit f2165627319f ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net Fixes: f2165627319f ("btrfs: compression: don't try to compress if we don't have enough pages") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we free a page whose order is very close to MAX_ORDER and greater
than pageblock_order, it wastes some CPU cycles to increase max_order to
MAX_ORDER one by one and check the pageblock migratetype of that page
repeatedly especially when MAX_ORDER is much larger than pageblock_order.
We also should not be checking migratetype of buddy when "order ==
MAX_ORDER - 1" as the buddy pfn may be invalid, so adjust the condition.
With the new check, we don't need the max_order check anymore, so we
replace it.
Also adjust max_order initialization so that it's lower by one than
previously, which makes the code hopefully more clear.
Link: https://lkml.kernel.org/r/20201204155109.55451-1-songmuchun@bytedance.com Fixes: d9dddbf55667 ("mm/page_alloc: prevent merging between isolated and other pageblocks") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.globl sets the symbol binding to STB_GLOBAL while .weak sets the
binding to STB_WEAK. GNU as let .weak override .globl since
binutils-gdb 5ca547dc2399a0a5d9f20626d4bf5547c3ccfddd (1996). Clang
integrated assembler let the last win but it may error in the future.
Since it is a convention that only one binding directive is used, just
delete .globl.
Fixes: ee9d21b3b358 ("powerpc/boot: Ensure _zimage_start is a weak symbol") Signed-off-by: Fangrui Song <maskray@google.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200325164257.170229-1-maskray@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RPC server procedures are normally expected to return a __be32 encoded
status value of type 'enum rpc_accept_stat', however at least one function
wants to return an authentication status of type 'enum rpc_auth_stat'
in the case where authentication fails.
This patch adds functionality to allow this.
Fixes: a4e187d83d88 ("NFS: Don't drop CB requests with invalid principals") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RFC792, ICMP errors should be sent to the source host.
However, in configurations with Virtual Routing and Forwarding tables,
looking up which routing table to use is currently done by using the
destination net_device.
commit 9d1a6c4ea43e ("net: icmp_route_lookup should use rt dev to
determine L3 domain") changes the interface passed to
l3mdev_master_ifindex() and inet_addr_type_dev_table() from skb_in->dev
to skb_dst(skb_in)->dev. This effectively uses the destination device
rather than the source device for choosing which routing table should be
used to lookup where to send the ICMP error.
Therefore, if the source and destination interfaces are within separate
VRFs, or one in the global routing table and the other in a VRF, looking
up the source host in the destination interface's routing table will
fail if the destination interface's routing table contains no route to
the source host.
One observable effect of this issue is that traceroute does not work in
the following cases:
- Route leaking between global routing table and VRF
- Route leaking between VRFs
Preferably use the source device routing table when sending ICMP error
messages. If no source device is set, fall-back on the destination
device routing table. Else, use the main routing table (index 0).
[ It has been pointed out that a similar issue may exist with ICMP
errors triggered when forwarding between network namespaces. It would
be worthwhile to investigate, but is outside of the scope of this
investigation. ]
[ It has also been pointed out that a similar issue exists with
unreachable / fragmentation needed messages, which can be triggered by
changing the MTU of eth1 in r1 to 1400 and running:
ip netns exec h1 ping -s 1450 -Mdo -c1 172.16.2.2
Some investigation points to raw_icmp_error() and raw_err() as being
involved in this last scenario. The focus of this patch is TTL expired
ICMP messages, which go through icmp_route_lookup.
Investigation of failure modes related to raw_icmp_error() is beyond
this investigation's scope. ]
Fixes: 9d1a6c4ea43e ("net: icmp_route_lookup should use rt dev to determine L3 domain") Link: https://tools.ietf.org/html/rfc792 Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is one use-after-free in ip_check_mc_rcu.
In ip_mc_del_src, the ip_sf_list of pmc has been freed under pmc->lock protection.
But access to ip_sf_list in ip_check_mc_rcu is not protected by the lock.
Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec8536580 ("ARM: imx: add missing clk_disable_unprepare()") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.
Fixes: ec16dae5453e ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams") Cc: stable@vger.kernel.org Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the backport of commit bdcf1dc25324 ("clk: Evict unregistered clks
from parent caches") to the 4.19.y and 4.14.y stable trees, the
orphan_list structure was placed in the wrong location, causing loads of
build warnings on systems that do not define CONFIG_DEBUG_FS.
Fix this up by moving the structure to the correct place in the file.
Syzkaller reported a divide error in snd_pcm_lib_ioctl. fifo_size
is of type snd_pcm_uframes_t(unsigned long). If frame_size
is 0x100000000, the error occurs.
The system currently warns if the config conditions for
building return_address in arch/arm/kernel/return_address.c
are not met, leaving just an EXPORT_SYMBOL_GPL(return_address)
of a function defined to be 'static linline'.
This is a result of aeea3592a13b ("ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h").
Since we're not going to build anything other than an exported
symbol for something that is already being defined to be an
inline-able return of NULL, just avoid building the code to
remove the following warning:
Fixes: aeea3592a13b ("ARM: 8158/1: LLVMLinux: use static inline in ARM ftrace.h") Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for cryptoloop has been officially marked broken and deprecated
in favor of dm-crypt (which supports the same broken algorithms if
needed) in Linux 2.6.4 (released in March 2004), and support for it has
been entirely removed from losetup in util-linux 2.23 (released in April
2013). Add a warning and a deprecation schedule.
Thanks to Kees Cook who detected the problem of memset that starting
from not the first member, but sized for the whole struct.
The better change will be to remove the redundant memset and to clear
only the msix_cnt member.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Reported-by: Kees Cook <keescook@chromium.org> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
macb_ptp_desc will not return NULL under most circumstances with correct
Kconfig and IP design config register. But for the sake of the extreme
corner case, check for NULL when using the helper. In case of rx_tstamp,
no action is necessary except to return (similar to timestamp disabled)
and warn. In case of TX, return -EINVAL to let the skb be free. Perform
this check before marking skb in progress.
Fixes coverity warning:
(4) Event dereference:
Dereferencing a null pointer "desc_ptp"
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For VFs we should return with an error in case we didn't get the exact
number of msix vectors as we requested.
Not doing that will lead to a crash when starting queues for this VF.
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The location of the system.data extended attribute can change whenever
xattr_sem is not taken. So we need to recalculate the i_inline_off
field since it mgiht have changed between ext4_write_begin() and
ext4_write_end().
This means that caching i_inline_off is probably not helpful, so in
the long run we should probably get rid of it and shrink the in-memory
ext4 inode slightly, but let's fix the race the simple way for now.
Cc: stable@kernel.org Fixes: f19d5870cbf72 ("ext4: add normal write support for inline data") Reported-by: syzbot+13146364637c7363a7de@syzkaller.appspotmail.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common implementation of isatty(3) involves calling a ioctl passing
a dummy struct argument and checking whether the syscall failed --
bionic and glibc use TCGETS (passing a struct termios), and musl uses
TIOCGWINSZ (passing a struct winsize). If the FD is a socket, we will
copy sizeof(struct ifreq) bytes of data from the argument and return
-EFAULT if that fails. The result is that the isatty implementations
may return a non-POSIX-compliant value in errno in the case where part
of the dummy struct argument is inaccessible, as both struct termios
and struct winsize are smaller than struct ifreq (at least on arm64).
Although there is usually enough stack space following the argument
on the stack that this did not present a practical problem up to now,
with MTE stack instrumentation it's more likely for the copy to fail,
as the memory following the struct may have a different tag.
Fix the problem by adding an early check for whether the ioctl is a
valid socket ioctl, and return -ENOTTY if it isn't.
Fixes: 44c02a2c3dc5 ("dev_ioctl(): move copyin/copyout to callers") Link: https://linux-review.googlesource.com/id/I869da6cf6daabc3e4b7b82ac979683ba05e27d4d Signed-off-by: Peter Collingbourne <pcc@google.com> Cc: <stable@vger.kernel.org> # 4.19 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch breaks userspace implementations (e.g. fdutils) and introduces
regressions in behaviour. Previously, it was possible to O_NDELAY open a
floppy device with no media inserted or with write protected media without
an error. Some userspace tools use this particular behavior for probing.
It's not the first time when we revert this patch. Previous revert is in
commit f2791e7eadf4 (Revert "floppy: refactor open() flags handling").
Mark NX as being used for all non-nested shadow MMUs, as KVM will set the
NX bit for huge SPTEs if the iTLB mutli-hit mitigation is enabled.
Checking the mitigation itself is not sufficient as it can be toggled on
at any time and KVM doesn't reset MMU contexts when that happens. KVM
could reset the contexts, but that would require purging all SPTEs in all
MMUs, for no real benefit. And, KVM already forces EFER.NX=1 when TDP is
disabled (for WP=0, SMEP=1, NX=0), so technically NX is never reserved
for shadow MMUs.
Fixes: b8e8c8303ff2 ("kvm: mmu: ITLB_MULTIHIT mitigation") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210622175739.3610207-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sudip: use old path and adjust context] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A fb_ioctl() FBIOPUT_VSCREENINFO call with invalid xres setting
or yres setting in struct fb_var_screeninfo will result in a
KASAN: vmalloc-out-of-bounds failure in bitfill_aligned() as
the margins are being cleared. The margins are cleared in
chunks and if the xres setting or yres setting is a value of
zero upto the chunk size, the failure will occur.
Add a margin check to validate xres and yres settings.
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba6b ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org> Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
If the endpoint completion callback is call right after the ep_enabled flag
is cleared and before usb_ep_dequeue() is call, we could do a double free
on the request and the associated buffer.
Fix this by clearing ep_enabled after all the endpoint requests have been
dequeued.
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab225 ("drivers: net: xgene-v2: Add MDIO support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.
This patch deals with ipv4 code.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23aa ("e1000e: add support for LTR on I217/I218") Suggested-by: Yee Li <seven.yi.lee@gmail.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so") Cc: <stable@vger.kernel.org> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu Cc: stable@vger.kernel.org Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Reported-by: Minmin chen <chenmingmin@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
However, as a runtime result, we get 2 instead of 1, meaning the dst
register does not contain (u32)-1 in this case. The reason is fairly
straight forward given the 0 test leaves the dst register as-is:
# ./bpftool p d x i 23
0: (b7) r0 = 0
1: (b7) r1 = -1
2: (b4) w2 = -1
3: (16) if w0 == 0x0 goto pc+1
4: (9c) w1 %= w0
5: (b7) r0 = 1
6: (1d) if r1 == r2 goto pc+1
7: (b7) r0 = 2
8: (95) exit
This was originally not an issue given the dst register was marked as
completely unknown (aka 64 bit unknown). However, after 468f6eafa6c4
("bpf: fix 32-bit ALU op verification") the verifier casts the register
output to 32 bit, and hence it becomes 32 bit unknown. Note that for
the case where the src register is unknown, the dst register is marked
64 bit unknown. After the fix, the register is truncated by the runtime
and the test passes:
Fixes: 468f6eafa6c4 ("bpf: fix 32-bit ALU op verification") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com>
[Salvatore Bonaccorso: This is an earlier version based on work by
Daniel and John which does not rely on availability of the BPF_JMP32
instruction class. This means it is not even strictly a backport of the
upstream commit mentioned but based on Daniel's and John's work to
address the issue and was finalized by Thadeu Lima de Souza Cascardo.] Tested-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing a different fix, John and I noticed an oddity in one of the
BPF program dumps that stood out, for example:
# bpftool p d x i 13
0: (b7) r0 = 808464450
1: (b4) w4 = 808464432
2: (bc) w0 = w0
3: (15) if r0 == 0x0 goto pc+1
4: (9c) w4 %= w0
[...]
In line 2 we noticed that the mov32 would 32 bit truncate the original src
register for the div/mod operation. While for the two operations the dst
register is typically marked unknown e.g. from adjust_scalar_min_max_vals()
the src register is not, and thus verifier keeps tracking original bounds,
simplified:
Runtime result of r0 at exit is 0 instead of expected -1. Remove the
verifier mov32 src rewrite in div/mod and replace it with a jmp32 test
instead. After the fix, we result in the following code generation when
having dividend r1 and divisor r6:
x86 in particular can throw a 'divide error' exception for div
instruction not only for divisor being zero, but also for the case
when the quotient is too large for the designated register. For the
edx:eax and rdx:rax dividend pair it is not an issue in x86 BPF JIT
since we always zero edx (rdx). Hence really the only protection
needed is against divisor being zero.
Fixes: 68fda450a7df ("bpf: fix 32-bit divide by zero") Co-developed-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
[Salvatore Bonaccorso: This is an earlier version of the patch provided
by Daniel Borkmann which does not rely on availability of the BPF_JMP32
instruction class. This means it is not even strictly a backport of the
upstream commit mentioned but based on Daniel's and John's work to
address the issue.] Tested-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Fri, 27 Aug 2021 13:55:31 +0000 (10:55 -0300)]
bpf: Do not use ax register in interpreter on div/mod
Partially undo old commit 144cd91c4c2b ("bpf: move tmp variable into ax
register in interpreter"). The reason we need this here is because ax
register will be used for holding temporary state for div/mod instruction
which otherwise interpreter would corrupt. This will cause a small +8 byte
stack increase for interpreter, but with the gain that we can use it from
verifier rewrites as scratch register.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com>
[cascardo: This partial revert is needed in order to support using AX for
the following two commits, as there is no JMP32 on 4.19.y] Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got a problem on MIPS with Big-Endian is turned on: every time when
NF trying to change TCP MSS it returns because of new.v16 was greater
than old.v16. But real MSS was 1460 and my rule was like this:
add rule table chain tcp option maxseg size set 1400
And 1400 is lesser that 1460, not greater.
Later I founded that main causer is cast from u32 to __be16.
Debugging:
In example MSS = 1400(HEX: 0x578). Here is representation of each byte
like it is in memory by addresses from left to right(e.g. [0x0 0x1 0x2
0x3]). LE — Little-Endian system, BE — Big-Endian, left column is type.
LE BE
u32: [78 05 00 00] [00 00 05 78]
As you can see, u32 representation will be casted to u16 from different
half of 4-byte address range. But actually nf_tables uses registers and
store data of various size. Actually TCP MSS stored in 2 bytes. But
registers are still u32 in definition:
So, access like regs->data[priv->sreg] exactly u32. So, according to
table presents above, per-byte representation of stored TCP MSS in
register will be:
LE BE
(u32)regs->data[]: [78 05 00 00] [05 78 00 00]
^^ ^^
We see that register uses just half of u32 and other 2 bytes may be
used for some another data. But in nft_exthdr_tcp_set_eval() it casted
just like u32 -> __be16:
new.v16 = src
But u32 overfill __be16, so it get 2 low bytes. For clarity draw
one more table(<xx xx> means that bytes will be used for cast).
LE BE
u32: [<78 05> 00 00] [00 00 <05 78>]
(u32)regs->data[]: [<78 05> 00 00] [05 78 <00 00>]
As you can see, for Little-Endian nothing changes, but for Big-endian we
take the wrong half. In my case there is some other data instead of
zeros, so new MSS was wrongly greater.
For shooting this bug I used solution for ports ranges. Applying of this
patch does not affect Little-Endian systems.
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 9e8925b67a ("locks: Allow disabling mandatory locking at compile
time"), attempts to mount filesystems with "-o mand" will fail.
Unfortunately, there is no other indiciation of the reason for the
failure.
Change how the function is defined for better readability. When
CONFIG_MANDATORY_FILE_LOCKING is disabled, printk a warning when
someone attempts to mount with -o mand.
Also, add a blurb to the mandatory-locking.txt file to explain about
the "mand" option, and the behavior one should expect when it is
disabled.
Reported-by: Jan Kara <jack@suse.cz> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com Signed-off-by: Marcin Bachry <hegel666@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Prike Liang <prike.liang@amd.com> Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cross-rename lacks a check when that would prevent exchanging a
directory and subvolume from different parent subvolume. This causes
data inconsistencies and is caught before commit by tree-checker,
turning the filesystem to read-only.
Calling the renameat2 with RENAME_EXCHANGE flags like
The corrupted data will not be written, and filesystem can be unmounted
and mounted again (all changes since the last commit will be lost).
Add the missing check for new_ino so that all non-subvolumes must reside
under the same parent subvolume. There's an exception allowing to
exchange two subvolumes from any parents as the directory representing a
subvolume is only a logical link and does not have any other structures
related to the parent subvolume, unlike files, directories etc, that
are always in the inode namespace of the parent subvolume.
Fixes: cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT") CC: stable@vger.kernel.org # 4.7+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling code in tpci200_register does not free interface_regs
allocated by ioremap and the current version of error handling code is
problematic.
Fix this by refactoring the error handling code and free interface_regs
when necessary.
Fixes: 43986798fd50 ("ipack: add error handling for ioremap_nocache") Cc: stable@vger.kernel.org Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210810100323.3938492-2-mudongliangabcd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function tpci200_register called by tpci200_install and
tpci200_unregister called by tpci200_uninstall are in pair. However,
tpci200_unregister has some cleanup operations not in the
tpci200_register. So the error handling code of tpci200_pci_probe has
many different double free issues.
Fix this problem by moving those cleanup operations out of
tpci200_unregister, into tpci200_pci_remove and reverting
the previous commit 9272e5d0028d ("ipack/carriers/tpci200:
Fix a double free in tpci200_pci_probe").
Fixes: 9272e5d0028d ("ipack/carriers/tpci200: Fix a double free in tpci200_pci_probe") Cc: stable@vger.kernel.org Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210810100323.3938492-1-mudongliangabcd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During suspend/resume NGD remote instance is power cycled along
with remotely controlled bam dma engine.
So Reset the dma configuration during this suspend resume path
so that we are not dealing with any stale dma setup.
Without this transactions timeout after first suspend resume path.
In some usecases transaction ids are dynamically allocated inside
the controller driver after sending the messages which have generic
acknowledge responses. So check for this before refcounting pm_runtime.
Without this we would end up imbalancing runtime pm count by
doing pm_runtime_put() in both slim_do_transfer() and slim_msg_response()
for a single pm_runtime_get() in slim_do_transfer()
As tid is unsigned its hard to figure out if the tid is valid or
invalid. So Start the transaction ids from 1 instead of zero
so that we could differentiate between a valid tid and invalid tids
This is useful in cases where controller would add a tid for controller
specific transfers.
The problem was the "trace(read_max,count)" where the "count" should be
"$count" as "onmax()" only handles variables (although it really should be
able to figure out that "count" is a field of sys_enter_read). But there's
a path that does not find the variable and ends up passing a NULL for the
event, which ends up getting passed to "strcmp()".
Add a check for NULL to return and error on the command with:
The original code in the cap_put_caller() function does not
handle correctly the positive values returned from the passed
function for multiple iterations. It means that the change
notifications may be lost.
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
qlcnic_83xx_unlock_flash() is called on all paths after we call
qlcnic_83xx_lock_flash(), except for one error path on failure
of QLCRD32(), which may cause a deadlock. This bug is suggested
by a static analysis tool, please advise.
Fixes: 81d0aeb0a4fff ("qlcnic: flash template based firmware reset recovery") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb044 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown") Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log