Paolo Abeni [Fri, 20 Apr 2018 11:18:16 +0000 (13:18 +0200)]
tun: do not compute the rxhash, if not needed
Currently, the tun driver, in absence of an eBPF steering program,
always compute the rxhash in its rx path, even when such value
is later unused due to additional checks (
This changeset moves the all the related checks just before the
__skb_get_hash_symmetric(), so that the latter is no more computed
when unneeded.
Also replace an unneeded RCU section with rcu_access_pointer().
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
lan78xx: Read configuration from Device Tree
The Microchip LAN78XX family of devices are Ethernet controllers with
a USB interface. Despite being discoverable devices it can be useful to
be able to configure them from Device Tree, particularly in low-cost
applications without an EEPROM or programmed OTP.
This patch set adds support for reading the MAC address and LED modes from
Device Tree.
v4:
- Rename nodes in bindings doc.
v3:
- Move LED setting into PHY driver.
v2:
- Use eth_platform_get_mac_address.
- Support up to 4 LEDs, and move LED mode constants into dt-bindings header.
- Improve bindings document.
- Remove EEE support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Elwell [Thu, 19 Apr 2018 16:59:40 +0000 (17:59 +0100)]
dt-bindings: Document the DT bindings for lan78xx
The Microchip LAN78XX family of devices are Ethernet controllers with
a USB interface. Despite being discoverable devices it can be useful to
be able to configure them from Device Tree, particularly in low-cost
applications without an EEPROM or programmed OTP.
Document the supported properties in a bindings file.
Signed-off-by: Phil Elwell <phil@raspberrypi.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Elwell [Thu, 19 Apr 2018 16:59:39 +0000 (17:59 +0100)]
lan78xx: Read LED states from Device Tree
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Elwell [Thu, 19 Apr 2018 16:59:38 +0000 (17:59 +0100)]
lan78xx: Read MAC address from DT if present
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: Phil Elwell <phil@raspberrypi.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpumask_local_spread to provide interrupt affinity hints
for each queue. This will spread interrupts across NUMA local
CPUs first, extending to remote nodes if needed.
Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Apr 2018 16:14:53 +0000 (09:14 -0700)]
net/ipv6: Fix ip6_convert_metrics() bug
If ip6_convert_metrics() fails to allocate memory, it should not
overwrite rt->fib6_metrics or we risk a crash later as syzbot found.
BUG: KASAN: null-ptr-deref in atomic_read include/asm-generic/atomic-instrumented.h:21 [inline]
BUG: KASAN: null-ptr-deref in refcount_sub_and_test+0x92/0x330 lib/refcount.c:179
Read of size 4 at addr 0000000000000044 by task syzkaller832429/4487
Fixes: d4ead6b34b67 ("net/ipv6: move metrics from dst to rt6_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Ahern <dsa@cumulusnetworks.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
qed* : Use trust mode to override forced MAC
This patchset adds a support to override forced MAC (MAC set by PF for a VF)
when trust mode is enabled using
First patch adds a real change to use .ndo_set_vf_trust to override forced MAC
and allow user to change VFs from VF interface itself.
Second patch takes care of a corner case, where MAC change from VF won't
take effect when VF interface is down, by introducing a new TLV
(a way to send message from VF to PF) to give a hint to PF to update
its bulletin board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qed* : Add new TLV to request PF to update MAC in bulletin board
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed* : use trust mode to allow VF to override forced MAC
As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.
This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 20 Apr 2018 15:20:06 +0000 (11:20 -0400)]
Merge branch 'geneve-mtu'
Alexey Kodanev says:
====================
geneve: verify user specified MTU or adjust with a lower device
The first two patches don't introduce any functional changes and
contain minor cleanups for code readability.
The last one adds a new function geneve_link_config() similar to the
other tunnels. The function will be used on a new link creation or
when 'remote' parameter is changed. It adjusts a user specified MTU
or, if it finds a lower device, tunes the tunnel MTU using it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.
This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
* on a new link creation
* when 'remote' parameter is changed
Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
geneve: check MTU for a minimum in geneve_change_mtu()
geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
geneve: cleanup hard coded value for Ethernet header length
Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
George Wilkie [Thu, 19 Apr 2018 10:34:14 +0000 (11:34 +0100)]
team: account for oper state
Account for operational state when determining port linkup state,
as per Documentation/networking/operstates.txt.
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tipc: Confgiuration of MTU for media UDP
Systematic measurements have shown that an emulated MTU of 14k for
UDP bearers is the optimal value for maximal throughput. Accordingly,
the default MTU of UDP bearers is changed to 14k.
We also provide users with a fallback option from this value,
by providing support to configure MTU for UDP bearers. The following
options are introduced which are symmetrical to the design of
confguring link tolerance.
- Configure media with new MTU value, which will take effect on
links going up after the moment it was configured. Alternatively,
the bearer has to be disabled and re-enabled, for existing links to
reflect the configured value.
- Configure bearer with new MTU value, which take effect on
running links dynamically.
Please note:
- User has to change MTU at both endpoints, otherwise the link
will fall back to smallest MTU after a reset.
- Failover from a link with higher MTU to a link with lower MTU
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc: confgiure and apply UDP bearer MTU on running links
Currently, we have option to configure MTU of UDP media. The configured
MTU takes effect on the links going up after that moment. I.e, a user
has to reset bearer to have new value applied across its links. This is
confusing and disturbing on a running cluster.
We now introduce the functionality to change the default UDP bearer MTU
in struct tipc_bearer. Additionally, the links are updated dynamically,
without any need for a reset, when bearer value is changed. We leverage
the existing per-link functionality and the design being symetrical to
the confguration of link tolerance.
Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In previous commit, we changed the default emulated MTU for UDP bearers
to 14k.
This commit adds the functionality to set/change the default value
by configuring new MTU for UDP media. UDP bearer(s) have to be disabled
and enabled back for the new MTU to take effect.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all bearers are configured with MTU value same as the
underlying L2 device. However, in case of bearers with media type
UDP, higher throughput is possible with a fixed and higher emulated
MTU value than adapting to the underlying L2 MTU.
In this commit, we introduce a parameter mtu in struct tipc_media
and a default value is set for UDP. A default value of 14k
was determined by experimentation and found to have a higher throughput
than 16k. MTU for UDP bearers are assigned the above set value of
media MTU.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added the ndo to gather VF statistics through the PF.
Collect VF statistics via mailbox from VF.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ave: add support for phy-mode setting of system controller
This patch adds support for specifying system controller that configures
phy-mode setting.
According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.
Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.
This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode
The DT property accepts one argument to distinguish them for multiple MAC
instances.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: ave: add syscon-phy-mode property to configure phy-mode setting
Add "socionext,syscon-phy-mode" property to specify system controller that
configures the settings about phy-mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ave: add multiple clocks and resets support as required property
When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.
The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.
In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.
To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.
Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel. Drivers should work without
such expectation.
Fixes: 4c270b55a5af ("net: ethernet: socionext: add AVE ethernet driver") Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.
Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Apr 2018 20:11:12 +0000 (16:11 -0400)]
Merge branch 'Amiga-xsurf100'
Michael Schmitz says:
====================
New network driver for Amiga X-Surf 100 (m68k)
[This is a resend of my v3 series which was based on the wrong version and
tree. Only substantial change is to Asix AX99796B PHY driver.]
This patch series adds support for the Individual Computers X-Surf 100
network card for m68k Amiga, a network adapter based on the AX88796 chip set.
The driver was originally written for kernel version 3.19 by Michael Karcher
(see CC:), and adapted to 4.16+ for submission to netdev by me. Questions
regarding motivation for some of the changes are probably best directed at
Michael Karcher.
The driver has been tested by Adrian <glaubitz@physik.fu-berlin.de> who will
send his Tested-by tag separately.
A few changes to the ax88796 driver were required:
- to read the MAC address, some setup of the ax99796 chip must be done,
- attach to the MII bus only on device open to allow module unloading,
- allow to supersede ax_block_input/ax_block_output by card-specific
optimized code,
- use an optional interrupt status callback to allow easier sharing of the
card interrupt,
- set IRQF_SHARED if platform IRQ resource is marked shareable
The Asix Electronix PHY used on the X-Surf 100 is buggy, and causes the
software reset to hang if the previous command sent to the PHY was also
a soft reset. This bug requires addition of a PHY driver for Asix PHYs
to provide a fixed .soft_reset function, included in this series.
Some additional cleanup:
- do not attempt to free IRQ in ax_remove (complements 82533ad9a1c),
- clear platform drvdata on probe fail and module remove.
Changes since v1:
Raised in review by Andrew Lunn:
- move MII code around to avoid need for forward declaration,
- combine patches 2 and 7 to add cleanup in error path
Changes since v2:
- corrected authorship attribution to Michael Karcher
Suggested by Geert Uytterhoeven:
- use ei_local->reset_8390() instead of duplicating ax_reset_8390(),
- use %pR to format struct resource pointers,
- assign pdev and xs100 pointers in declaration,
- don't split error messages,
- change Kconfig logic to only require XSURF100 set on Amiga
Suggested by Andrew Lunn:
- add COMPILE_TEST to ax88796 Kconfig options,
- use new Asix PHY driver for X-Surf 100
Suggested by Andrew Lunn/Finn Thain:
- declare struct sk_buff in ax88796.h,
- correct whitespace error in ax88796.h
Changes since v3:
- various checkpatch cleanup
Andrew Lunn:
- don't duplicate genphy_soft_reset in Asix PHY driver, just call
genphy_soft_reset after writing zero to control register
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:26 +0000 (14:05 +1200)]
net-next: New ax88796 platform driver for Amiga X-Surf 100 Zorro board (m68k)
Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Schmitz [Thu, 19 Apr 2018 02:05:25 +0000 (14:05 +1200)]
net-next: ax88796: release platform device drvdata on probe error and module remove
The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:24 +0000 (14:05 +1200)]
net-next: ax88796: set IRQF_SHARED flag when IRQ resource is marked as shareable
On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:23 +0000 (14:05 +1200)]
net-next: ax88796: add interrupt status callback to platform data
To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:22 +0000 (14:05 +1200)]
net-next: ax88796: Add block_input/output hooks to ax_plat_data
Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:21 +0000 (14:05 +1200)]
net-next: ax88796: Do not free IRQ in ax_remove() (already freed in ax_close()).
This complements the fix in 82533ad9a1c ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.
Fixes: 82533ad9a1c (net: ethernet: ax88796: don't call free_irq without request_irq first) Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:20 +0000 (14:05 +1200)]
net-next: ax88796: Attach MII bus only when open
Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().
This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Karcher [Thu, 19 Apr 2018 02:05:19 +0000 (14:05 +1200)]
net-next: ax88796: Fix MAC address reading
To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Schmitz [Thu, 19 Apr 2018 02:05:18 +0000 (14:05 +1200)]
net-next: phy: new Asix Electronics PHY driver
The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.
Add workaround driver just for this special case.
Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Apr 2018 19:59:12 +0000 (15:59 -0400)]
Merge branch 'Modernize-mdio-gpio'
Andrew Lunn says:
====================
Modernize mdio-gpio
This patchset is inspired by a previous version by Linus Walleij
It reworks the mdio-gpio code to make use of gpio descriptors instead
of gpio numbers. However compared to the previous version, it retains
support for platform devices. It does however remove the platform_data
header file. The needed GPIOs are now passed by making use of a gpiod
lookup table. e.g:
Andrew Lunn [Wed, 18 Apr 2018 23:02:58 +0000 (01:02 +0200)]
net: phy: mdio-gpio: Add #defines for the GPIO index's
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 18 Apr 2018 23:02:57 +0000 (01:02 +0200)]
net: phy: mdio-gpio: Parse properties directly into bitbang structure
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 18 Apr 2018 23:02:54 +0000 (01:02 +0200)]
net: phy: mdio-gpio: Remove support for IRQs in platform data
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:06 +0000 (15:39 -0700)]
net/ipv6: Fix gfp_flags arg to addrconf_prefix_route
Eric noticed that __ipv6_ifa_notify is called under rcu_read_lock, so
the gfp argument to addrconf_prefix_route can not be GFP_KERNEL.
While scrubbing other calls I noticed addrconf_addr_gen has one
place with GFP_ATOMIC that can be GFP_KERNEL.
Fixes: acb54e3cba404 ("net/ipv6: Add gfp_flags to route add functions") Reported-by: syzbot+2add39b05179b31f912f@syzkaller.appspotmail.com Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:04 +0000 (15:39 -0700)]
net/ipv6: Remove compare of fib6_idev from rt6_duplicate_nexthop
After 4832c30d5458 ("net: ipv6: put host and anycast routes on device
with address") the comparison of idev does not add value since it
correlates to the nexthop device which is already compared. Remove
the idev comparison.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:03 +0000 (15:39 -0700)]
net/ipv6: Change ip6_route_get_saddr to get dev from route
Prior to 4832c30d5458 ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.
Commit 4832c30d5458 changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change ip6_route_get_saddr can just pass the nexthop
device to ipv6_dev_get_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:02 +0000 (15:39 -0700)]
net/ipv6: Remove unnecessary checks on fib6_idev
Prior to 4832c30d5458 ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.
Commit 4832c30d5458 changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change a couple of device checks during route lookups
are no longer needed. Remove them.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:38:59 +0000 (15:38 -0700)]
net/ipv6: Rename fib6_info struct elements
Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.
Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 18 Apr 2018 18:43:15 +0000 (11:43 -0700)]
net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends
After working on IP defragmentation lately, I found that some large
packets defeat CHECKSUM_COMPLETE optimization because of NIC adding
zero paddings on the last (small) fragment.
While removing the padding with pskb_trim_rcsum(), we set skb->ip_summed
to CHECKSUM_NONE, forcing a full csum validation, even if all prior
fragments had CHECKSUM_COMPLETE set.
We can instead compute the checksum of the part we are trimming,
usually smaller than the part we keep.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tracking TCP data delivery and ECN stats
This patch series improve tracking the data delivery status
1. minor improvement on SYN data
2. accounting bytes delivered with CE marks
3. exporting the delivery stats to applications
s.t. users can get better sense of TCP performance at per host,
per connection, and even per application message level.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Export data delivered and delivered with CE marks to
1) SNMP TCPDelivered and TCPDeliveredCE
2) getsockopt(TCP_INFO)
3) Timestamping API SOF_TIMESTAMPING_OPT_STATS
Note that for SCM_TSTAMP_ACK, the delivery info in
SOF_TIMESTAMPING_OPT_STATS is reported before the info
was fully updated on the ACK.
These stats help application monitor TCP delivery and ECN status
on per host, per connection, even per message level.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: track total bytes delivered with ECN CE marks
Introduce a new delivered_ce stat in tcp socket to estimate
number of packets being marked with CE bits. The estimation is
done via ACKs with ECE bit. Depending on the actual receiver
behavior, the estimation could have biases.
Since the TCP sender can't really see the CE bit in the data path,
so the sender is technically counting packets marked delivered with
the "ECE / ECN-Echo" flag set.
With RFC3168 ECN, because the ECE bit is sticky, this count can
drastically overestimate the nummber of CE-marked data packets
With DCTCP-style ECN this should be reasonably precise unless there
is loss in the ACK path, in which case it's not precise.
With AccECN proposal this can be made still more precise, even in
the case some degree of ACK loss.
However this is sender's best estimate of CE information.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: better delivery accounting for SYN-ACK and SYN-data
the tcp_sock:delivered has inconsistent accounting for SYN and FIN.
1. it counts pure FIN
2. it counts pure SYN
3. it counts SYN-data twice
4. it does not count SYN-ACK
For congestion control perspective it does not matter much as C.C. only
cares about the difference not the aboslute value. But the next patch
would export this field to user-space so it's better to report the absolute
value w/o these caveats.
This patch counts SYN, SYN-ACK, or SYN-data delivery once always in
the "delivered" field.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2) ip6_input_finish()
ipv6_frag_rcv() (lock frag queue spinlock)
ip6_frag_queue()
icmpv6_param_prob() (lock txq->_xmit_lock at some point)
We could add lockdep annotations, but we also can make sure IPv6
calls icmpv6_param_prob() only after the release of the frag queue spinlock,
since this naturally makes frag queue spinlock a leaf in lock hierarchy.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Tue, 17 Apr 2018 21:25:30 +0000 (14:25 -0700)]
hv_netvsc: propogate Hyper-V friendly name into interface alias
This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.
The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.
In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.
The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.
Also requires exporting dev_set_alias in netdev core.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: remove jumbo_tx_csum from chip config struct
According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.
By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000
In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons since commit ad67b74d2469 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.
When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Apr 2018 01:00:58 +0000 (21:00 -0400)]
Merge branch 'netcp-K2G-SoC-support'
Murali Karicheri says:
====================
Add support for netcp driver on K2G SoC
K2G SoC is another variant of Keystone family of SoCs. This patch
series add support for NetCP driver on this SoC. The QMSS found on
K2G SoC is a cut down version of the QMSS found on other keystone
devices with less number of queues, internal link ram etc. The patch
series has 2 patch sets that goes into the drivers/soc and the
rest has to be applied to net sub system. Please review and merge
if this looks good.
K2G TRM is located at http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf
Thanks
The boot logs on K2G ICE board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/yvZ6drFhkW/
The boot logs on K2G GP board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/QTr6K7s4Zp/
Also regressed boot on K2HK and K2L EVMs as we have modified GBE
version detection logic (K2E uses same version of NetCP as in K2L.
So regression on one of them is needed).
Boot log on K2L and K2HK EVMs are at
https://pastebin.ubuntu.com/p/N9DBdPjbvR/
This series applies to net-next master branch.
Change history:
v4 - ready for merge to net-next
Folded the series "Add promiscous mode support in k2g network driver"
into this.
Fixed a typo in 5/11 (sgmii to rgmii) based on TI internal comment
Reworked 4/11 and title changed to reflect additional changes to
exclude sgmii configuration code for 2U cpsw. Use IS_SS_ID_2U()
macro for customization.
Added Reviewed-by from Rob Herring against 1/13
v3 - Addressed comments from Andrew Lunn and Grygorii Strashko
against v2.
v2 - Addressed following comments on initial version
- split patch 3/5 to multiple patches from Andrew Lunn
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: k2g: add promiscuous mode support
This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: add api to support set rx mode in netcp modules
This patch adds an API to support setting rx mode in
netcp modules. If a netcp module needs to be notified
when upper layer transitions from one rx mode to
another and react accordingly, such a module will implement
the new API set_rx_mode added in this patch. Currently
rx modes supported are PROMISCUOUS and NON_PROMISCUOUS
modes.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: use of_get_phy_mode() to support different RGMII modes
The phy used for K2G allows for internal delays to be added optionally
to the clock circuitry based on board desing. To add this support,
enhance the driver to use of_get_phy_mode() to read the phy-mode from
the phy device and pass the same to phy through of_phy_connect().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: re-use stats handling code for 2u hardware
The stats block in 2u cpsw hardware is similar to the one on nu
and hence handle it in a similar way by using a macro that includes
2u hardware as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: add support for handling rgmii link interface
2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: make sgmii configuration conditional
As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: use macro for checking ss_version consistently
Driver currently uses macro for NU and XBE hardwrae, while other
places for older hardware such as that on K2H/K SoC (version 1.4
of the cpsw hardware, it explicitly check for the ss_version
inline. Add a new macro for version 1.4 and use it to customize
code in the driver. While at it also fix similar issue with
checking XBE version by re-using existing macro IS_SS_ID_XGBE().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / users / willy / xarray.git / log