tpacket_snd(), packet_snd(), packet_getname() and packet_seq_show()
can read po->num without holding a lock. This means other threads
can change po->num at the same time.
KCSAN complained about this known fact [1]
Add READ_ONCE()/WRITE_ONCE() to address the issue.
[1] BUG: KCSAN: data-race in packet_do_bind / packet_sendmsg
write to 0xffff888131a0dcc0 of 2 bytes by task 24714 on cpu 0:
packet_do_bind+0x3ab/0x7e0 net/packet/af_packet.c:3181
packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
__sys_bind+0x200/0x290 net/socket.c:1637
__do_sys_bind net/socket.c:1648 [inline]
__se_sys_bind net/socket.c:1646 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1646
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888131a0dcc0 of 2 bytes by task 24719 on cpu 1:
packet_snd net/packet/af_packet.c:2899 [inline]
packet_sendmsg+0x317/0x3570 net/packet/af_packet.c:3040
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2433
__do_sys_sendmsg net/socket.c:2442 [inline]
__se_sys_sendmsg net/socket.c:2440 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2440
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000 -> 0x1200
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24719 Comm: syz-executor.5 Not tainted 5.13.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported memory leak in tty_init_dev().
The problem was in unputted tty in ldisc_open()
static int ldisc_open(struct tty_struct *tty)
{
...
ser->tty = tty_kref_get(tty);
...
result = register_netdevice(dev);
if (result) {
rtnl_unlock();
free_netdev(dev);
return -ENODEV;
}
...
}
Ser pointer is netdev private_data, so after free_netdev()
this pointer goes away with unputted tty reference. So, fix
it by adding tty_kref_put() before freeing netdev.
Reported-and-tested-by: syzbot+f303e045423e617d2cad@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current logic is performing hard reset and causing the programmed
registers to be wiped out.
as per datasheet: https://www.ti.com/lit/ds/symlink/dp83867cr.pdf
8.6.26 Control Register (CTRL)
do SW_RESTART to perform a reset not including the registers,
If performed when link is already present,
it will drop the link and trigger re-auto negotiation.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Geet Modi <geet.modi@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 31039 Comm: syz-executor.2 Not tainted 5.13.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function 'ping_queue_rcv_skb' not always return success, which will
also return fail. If not check the wrong return value of it, lead to function
`ping_rcv` return success.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several ethtool functions leave heap uncleared (potentially) by
drivers. This will leave the unused portion of heap unchanged and
might copy the full contents back to userspace.
Signed-off-by: Austin Kim <austindh.kim@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 'nla_parse_nested_deprecated' failed, it's no need to
BUG() here, return -EINVAL is ok.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
If the userland switches back-and-forth between NL80211_IFTYPE_OCB and
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), there is a
chance where the cleanup cfg80211_leave_ocb() is not called. This leads
to initialization of in-use memory (e.g. init u.ibss while in-use by
u.ocb) due to a shared struct/union within ieee80211_sub_if_data:
Syzbot reports that we may be able to get into a situation where
mac80211 has pending ACK frames on shutdown with hwsim. It appears
that the reason for this is that syzbot uses the wmediumd hooks to
intercept/injection frames, and may shut down hwsim, removing the
radio(s), while frames are pending in the air simulation.
Clean out the pending queue when the interface is stopped, after
this the frames can't be reported back to mac80211 properly anyway.
Syzbot reports that it's possible to hit this from userspace,
by trying to add a station before any other connection setup
has been done. Instead of trying to catch this in some other
way simply remove the warning, that will appropriately reject
the call from userspace.
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Revert commit 4514d991d992 ("PCI: PM: Do not read power state in
pci_enable_device_flags()") that is reported to cause PCI device
initialization issues on some systems.
With the latest mkimage from U-Boot 2021.04, the generic defconfigs no
longer build, failing with:
/usr/bin/mkimage: verify_header failed for FIT Image support with exit code 1
This is expected after the linked U-Boot commits because '@' is
forbidden in the node names due to the way that libfdt treats nodes with
the same prefix but different unit addresses.
Switch the '@' in the node name to '-'. Drop the unit addresses from the
hash and kernel child nodes because there is only one node so they do
not need to have a number to differentiate them.
With GNU binutils 2.35+, linking with BFD produces warnings for vmlinux:
aarch64-linux-gnu-ld: warning: -z norelro ignored
BFD can produce this warning when the target emulation mode does not
support RELRO program headers, and -z relro or -z norelro is passed.
Alan Modra clarifies:
The default linker emulation for an aarch64-linux ld.bfd is
-maarch64linux, the default for an aarch64-elf linker is
-maarch64elf. They are not equivalent. If you choose -maarch64elf
you get an emulation that doesn't support -z relro.
The ARCH=arm64 kernel prefers -maarch64elf, but may fall back to
-maarch64linux based on the toolchain configuration.
LLD will always create RELRO program header regardless of target
emulation.
To avoid the above warning when linking with BFD, pass -z norelro only
when linking with LLD or with -maarch64linux.
Fixes: 3b92fa7485eb ("arm64: link with -z norelro regardless of CONFIG_RELOCATABLE") Fixes: 3bbd3db86470 ("arm64: relocatable: fix inconsistencies in linker script and options") Cc: <stable@vger.kernel.org> # 5.0.x- Reported-by: kernelci.org bot <bot@kernelci.org> Reported-by: Quentin Perret <qperret@google.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Cc: Alan Modra <amodra@gmail.com> Cc: Fāng-ruì Sòng <maskray@google.com> Link: https://lore.kernel.org/r/20201218002432.788499-1-ndesaulniers@google.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly to the CC_IS_CLANG config, add LD_IS_LLD to avoid GNU ld
specific logic such as ld-version or ld-ifversion and gain the
ability to select potential features that depend on the linker at
configuration time such as LTO.
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
When building the kernel wtih gcc-10 or higher using the
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y flag, the compiler picks a slightly
different set of registers for the inline assembly in cpu_init() that
subsequently results in a corrupt kernel stack as well as remaining in
FIQ mode. If a banked register is used for the last argument, the wrong
version of that register gets loaded into CPSR_c. When building in Arm
mode, the arguments are passed as immediate values and the bug cannot
happen.
This got introduced when Daniel reworked the FIQ handling and was
technically always broken, but happened to work with both clang and gcc
before gcc-10 as long as they picked one of the lower registers.
This is probably an indication that still very few people build the
kernel in Thumb2 mode.
Marek pointed out the problem on IRC, Arnd narrowed it down to this
inline assembly and Russell pinpointed the exact bug.
Change the constraints to force the final mode switch to use a non-banked
register for the argument to ensure that the correct constant gets loaded.
Another alternative would be to always use registers for the constant
arguments to avoid the #ifdef that has now become more complex.
Cc: <stable@vger.kernel.org> # v3.18+ Cc: Daniel Thompson <daniel.thompson@linaro.org> Reported-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Fixes: c0e7f7ee717e ("ARM: 8150/3: fiq: Replace default FIQ handler") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Irrespective as to whether CONFIG_MODULE_SIG is configured, specifying
"module.sig_enforce=1" on the boot command line sets "sig_enforce".
Only allow "sig_enforce" to be set when CONFIG_MODULE_SIG is configured.
This patch makes the presence of /sys/module/module/parameters/sig_enforce
dependent on CONFIG_MODULE_SIG=y.
When do system reboot, it calls dwc3_shutdown and the whole debugfs
for dwc3 has removed first, when the gadget tries to do deinit, and
remove debugfs for its endpoints, it meets NULL pointer dereference
issue when call debugfs_lookup. Fix it by removing the whole dwc3
debugfs later than dwc3_drd_exit.
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly") Cc: stable <stable@vger.kernel.org> Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm timers instead.
Let's prepare for adding support for percpu timers by adding a common
dmtimer_clkevt_init_common() and call it from __omap_sync32k_timer_init().
This patch makes no intentional functional changes.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: backported to 5.4.y] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can move the TI dmtimer clockevent and clocksource to live under
drivers/clocksource if we rely only on the clock framework, and handle
the module configuration directly in the clocksource driver based on the
device tree data.
This removes the early dependency with system timers to the interconnect
related code, and we can probe pretty much everything else later on at
the module_init level.
Let's first add a new driver for timer-ti-dm-systimer based on existing
arch/arm/mach-omap2/timer.c. Then let's start moving SoCs to probe with
device tree data while still keeping the old timer.c. And eventually we
can just drop the old timer.c.
Let's take the opportunity to switch to use readl/writel as pointed out
by Daniel Lezcano <daniel.lezcano@linaro.org>. This allows further
clean-up of the timer-ti-dm code the a lot of the shared helpers can
just become static to the non-syster related code.
Note the boards can optionally configure different timer source clocks
if needed with assigned-clocks and assigned-clock-parents.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: backported to 5.4.y] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading the base address of the a REDIST region
through KVM_VGIC_V3_ADDR_TYPE_REDIST we expect the
redistributor region list to be populated with a single
element.
However list_first_entry() expects the list to be non empty.
Instead we should use list_first_entry_or_null which effectively
returns NULL if the list is empty.
Fixes: dbd9733ab674 ("KVM: arm/arm64: Replace the single rdist region by a list") Cc: <Stable@vger.kernel.org> # v4.18+ Signed-off-by: Eric Auger <eric.auger@redhat.com> Reported-by: Gavin Shan <gshan@redhat.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210412150034.29185-1-eric.auger@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
321827477360934d ("icmp: don't send out ICMP messages with a source address of 0.0.0.0")
That don't result in any change in tooling, as INADDR_ are not used to
generate id->string tables used by 'perf trace'.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().
Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().
Fixes: commit d2ed0a7755fe ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The redzone area for SLUB exists between s->object_size and s->inuse
(which is at least the word-aligned object_size). If a cache were
created with an object_size smaller than sizeof(void *), the in-object
stored freelist pointer would overwrite the redzone (e.g. with boot
param "slub_debug=ZF"):
BUG test (Tainted: G B ): Right Redzone overwritten
-----------------------------------------------------------------------------
Store the freelist pointer out of line when object_size is smaller than
sizeof(void *) and redzoning is enabled.
Additionally remove the "smaller than sizeof(void *)" check under
CONFIG_DEBUG_VM in kmem_cache_sanity_check() as it is now redundant:
SLAB and SLOB both handle small sizes.
(Note that no caches within this size range are known to exist in the
kernel currently.)
Link: https://lkml.kernel.org/r/20210608183955.280836-3-keescook@chromium.org Fixes: 81819f0fc828 ("SLUB core") Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: "Lin, Zhenpeng" <zplin@psu.edu> Cc: Marco Elver <elver@google.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "Actually fix freelist pointer vs redzoning", v4.
This fixes redzoning vs the freelist pointer (both for middle-position
and very small caches). Both are "theoretical" fixes, in that I see no
evidence of such small-sized caches actually be used in the kernel, but
that's no reason to let the bugs continue to exist, especially since
people doing local development keep tripping over it. :)
This patch (of 3):
Instead of repeating "Redzone" and "Poison", clarify which sides of
those zones got tripped. Additionally fix column alignment in the
trailer.
BUG test (Tainted: G B ): Right Redzone overwritten
...
Redzone (____ptrval____): bb bb bb bb bb bb bb bb ........
Object (____ptrval____): f6 f4 a5 40 1d e8 ...@..
Redzone (____ptrval____): 1a aa ..
Padding (____ptrval____): 00 00 00 00 00 00 00 00 ........
The earlier commits that slowly resulted in the "Before" reporting were:
d86bd1bece6f ("mm/slub: support left redzone") ffc79d288000 ("slub: use print_hex_dump") 2492268472e7 ("SLUB: change error reporting format to follow lockdep loosely")
The egress tunnel code uses dst_clone() and directly sets the result
which is wrong because the entry might have 0 refcnt or be already deleted,
causing number of problems. It also triggers the WARN_ON() in dst_hold()[1]
when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and
checking if a reference was actually taken before setting the dst.
Cc: stable@vger.kernel.org Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org Fixes: 11538d039ac6 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang") Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If cfg80211_pmsr_process_abort() moves all the PMSR requests that
need to be freed into a local list before aborting and freeing them.
As a result, it is possible that cfg80211_pmsr_complete() will run in
parallel and free the same PMSR request.
Fix it by freeing the request in cfg80211_pmsr_complete() only if it
is still in the original pmsr list.
If all net/wireless/certs/*.hex files are deleted, the build
will hang at this point since the 'cat' command will have no
arguments. Do "echo | cat - ..." so that even if the "..."
part is empty, the whole thing won't hang.
If access_ok() or fpregs_soft_set() fails in __fpu__restore_sig() then the
function just returns but does not clear the FPU state as it does for all
other fatal failures.
Clear the FPU state for these failures as well.
Fixes: 72a671ced66d ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/87mtryyhhz.ffs@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the xfeatures bit is 0 and therefore the value in the xsave
storage is not valid, get_xsave_addr() returns NULL and switch_to()
writes the default PKRU. -> FAIL #1!
So that wrecks any copy_to/from_user() on the way back to user space
which hits memory which is protected by the default PKRU value.
Assumed that this does not fail (pure luck) then T1 goes back to user
space and because TIF_NEED_FPU_LOAD is set it ends up in
switch_fpu_return()
__fpregs_load_activate()
if (!fpregs_state_valid()) {
load_XSTATE_from_task();
}
But if nothing touched the FPU between T1 scheduling out and back in,
then the fpregs_state is still valid which means switch_fpu_return()
does nothing and just clears TIF_NEED_FPU_LOAD. Back to user space with
DEFAULT_PKRU loaded. -> FAIL #2!
The fix is simple: if get_xsave_addr() returns NULL then set the
PKRU value to 0 instead of the restrictive default PKRU value in
init_pkru_value.
switch_fpu_finish() checks current->mm as indicator for kernel threads.
That's wrong because kernel threads can temporarily use a mm of a user
process via kthread_use_mm().
ARCv2 has some configuration dependent registers (r30, r58, r59) which
could be targetted by the compiler. To keep the ABI stable, these were
unconditionally part of the glibc ABI
(sysdeps/unix/sysv/linux/arc/sys/ucontext.h:mcontext_t) however we
missed populating them (by saving/restoring them across signal
handling).
This patch fixes the issue by
- adding arcv2 ABI regs to kernel struct sigcontext
- populating them during signal handling
Change to struct sigcontext might seem like a glibc ABI change (although
it primarily uses ucontext_t:mcontext_t) but the fact is
- it has only been extended (existing fields are not touched)
- the old sigcontext was ABI incomplete to begin with anyways
Immediately reset the MMU context when the vCPU's SMM flag is cleared so
that the SMM flag in the MMU role is always synchronized with the vCPU's
flag. If RSM fails (which isn't correctly emulated), KVM will bail
without calling post_leave_smm() and leave the MMU in a bad state.
The bad MMU role can lead to a NULL pointer dereference when grabbing a
shadow page's rmap for a page fault as the initial lookups for the gfn
will happen with the vCPU's SMM flag (=0), whereas the rmap lookup will
use the shadow page's SMM flag, which comes from the MMU (=1). SMM has
an entirely different set of memslots, and so the initial lookup can find
a memslot (SMM=0) and then explode on the rmap memslot lookup (SMM=1).
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
The Broadcom BCM57414 NIC may be a multi-function device. While it does
not advertise an ACS capability, peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Trying to start a new PIO transfer by writing value 0 in PIO_START register
when previous transfer has not yet completed (which is indicated by value 1
in PIO_START) causes an External Abort on CPU, which results in kernel
panic:
SError Interrupt on CPU0, code 0xbf000002 -- SError
Kernel panic - not syncing: Asynchronous SError Interrupt
To prevent kernel panic, it is required to reject a new PIO transfer when
previous one has not finished yet.
If previous PIO transfer is not finished yet, the kernel may issue a new
PIO request only if the previous PIO transfer timed out.
In the past the root cause of this issue was incorrectly identified (as it
often happens during link retraining or after link down event) and special
hack was implemented in Trusted Firmware to catch all SError events in EL3,
to ignore errors with code 0xbf000002 and not forwarding any other errors
to kernel and instead throw panic from EL3 Trusted Firmware handler.
Links to discussion and patches about this issue:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50
https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/
https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
But the real cause was the fact that during link retraining or after link
down event the PIO transfer may take longer time, up to the 1.44s until it
times out. This increased probability that a new PIO transfer would be
issued by kernel while previous one has not finished yet.
After applying this change into the kernel, it is possible to revert the
mentioned TF-A hack and SError events do not have to be caught in TF-A EL3.
Link: https://lore.kernel.org/r/20210608203655.31228-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 7fbcb5da811b ("PCI: aardvark: Don't rely on jiffies while holding spinlock") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
advk_pcie_wait_pio() can be called while holding a spinlock (from
pci_bus_read_config_dword()), then depends on jiffies in order to
timeout while polling on PIO state registers. In the case the PIO
transaction failed, the timeout will never happen and will also cause
the cpu to stall.
This decrements a variable and wait instead of using jiffies.
Signed-off-by: Remi Pommarel <repk@triplefau.lt> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the
device inoperable for the current system boot. It requires a system
hard-reboot to get the GPU device back to normal operating condition
post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the
issue.
This issue will be fixed in the next generation of hardware.
Link: https://lore.kernel.org/r/20210608054857.18963-8-ameynarkhede03@gmail.com Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Sinan Kaya <okaya@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS
automatically disables LTSSM when Secondary Bus Reset is received and
device stops working. Prevent bus reset for these devices. With this
change, the device can be assigned to VMs with VFIO, but it will leak state
between VMs.
Reference: https://e2e.ti.com/support/processors/f/791/t/954382 Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com Signed-off-by: Antti Järvinen <antti.jarvinen@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trace_clock_global() tries to make sure the events between CPUs is
somewhat in order. A global value is used and updated by the latest read
of a clock. If one CPU is ahead by a little, and is read by another CPU, a
lock is taken, and if the timestamp of the other CPU is behind, it will
simply use the other CPUs timestamp.
The lock is also only taken with a "trylock" due to tracing, and strange
recursions can happen. The lock is not taken at all in NMI context.
In the case where the lock is not able to be taken, the non synced
timestamp is returned. But it will not be less than the saved global
timestamp.
The problem arises because when the time goes "backwards" the time
returned is the saved timestamp plus 1. If the lock is not taken, and the
plus one to the timestamp is returned, there's a small race that can cause
the time to go backwards!
The above case shows to reads of trace_clock_global() on the same CPU, but
the second read returns one less than the first read. That is, time when
backwards, and this is not what is allowed by trace_clock_global().
This was triggered by heavy tracing and the ring buffer checker that tests
for the clock going backwards:
A while ago, when the "trace" file was opened, tracing was stopped, and
code was added to stop recording the comms to saved_cmdlines, for mapping
of the pids to the task name.
Code has been added that only records the comm if a trace event occurred,
and there's no reason to not trace it if the trace file is opened.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The saved_cmdlines is used to map pids to the task name, such that the
output of the tracing does not just show pids, but also gives a human
readable name for the task.
If the name is not mapped, the output looks like this:
<...>-1316 [005] ...2 132.044039: ...
Instead of this:
gnome-shell-1316 [005] ...2 132.044039: ...
The names are updated when tracing is running, but are skipped if tracing
is stopped. Unfortunately, this stops the recording of the names if the
top level tracer is stopped, and not if there's other tracers active.
The recording of a name only happens when a new event is written into a
ring buffer, so there is no need to test if tracing is on or not. If
tracing is off, then no event is written and no need to test if tracing is
off or not.
Remove the check, as it hides the names of tasks for events in the
instance buffers.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d758 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub") Cc: stable@vger.kernel.org Signed-off-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a Use-after-Free found by the syzbot.
The problem is that a skb is taken from the per-session skb queue,
without incrementing the ref count. This leads to a Use-after-Free if
the skb is taken concurrently from the session queue due to a CTS.
syzbot is reporting hung task at register_netdevice_notifier() [1] and
unregister_netdevice_notifier() [2], for cleanup_net() might perform
time consuming operations while CAN driver's raw/bcm/isotp modules are
calling {register,unregister}_netdevice_notifier() on each socket.
Change raw/bcm/isotp modules to call register_netdevice_notifier() from
module's __init function and call unregister_netdevice_notifier() from
module's __exit function, as with gw/j1939 modules are doing.
On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between
struct members count and ival1. Even though all struct members are initialized,
the 4-byte hole will contain data from the kernel stack. This patch zeroes out
struct bcm_msg_head before usage, preventing infoleaks to userspace.
The scpi hwmon shows the sub-zero temperature in an unsigned integer,
which would confuse the users when the machine works in low temperature
environment. This shows the sub-zero temperature in an signed value and
users can get it properly from sensors.
I met a gpu addr bug recently and the kernel log
tells me the pc is memcpy/memset and link register is
radeon_uvd_resume.
As we know, in some architectures, optimized memcpy/memset
may not work well on device memory. Trival memcpy_toio/memset_io
can fix this problem.
BTW, amdgpu has already done it in:
commit ba0b2275a678 ("drm/amdgpu: use memcpy_to/fromio for UVD fw upload"),
that's why it has no this issue on the same gpu and platform.
Signed-off-by: Chen Li <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 'rt2880_pmx_group_enable' driver is printing an error and returning
-EBUSY if a pin has been already enabled. This begets anoying messages
in the caller when this happens like the following:
rt2880-pinmux pinctrl: pcie is already enabled
mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
To avoid this just print the already enabled message in the pinctrl
driver and return 0 instead to not confuse the user with a real
bad problem.
In U-boot side, an issue has been encountered when QSPI source clock is
running at low frequency (24 MHz for example), waiting for TCF bit to be
set didn't ensure that all data has been send out the FIFO, we should also
wait that BUSY bit is cleared.
To prevent similar issue in kernel driver, we implement similar behavior
by always waiting BUSY bit to be cleared.
The power of "LDO2", "MICBIAS1" and "Mic Det Power" were powered off after
the DAPM widgets were added, and these powers were set by the JD settings
"RT5659_JD_HDA_HEADER" in the probe function. In the codec probe function,
these powers were ignored to prevent them controlled by DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com> Signed-off-by: Jack Yu <jack.yu@realtek.com>
Message-Id: <15fced51977b458798ca4eebf03dafb9@realtek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The valid selectors for bd70528 bucks are 0 ~ 0xf, so the .n_voltages
should be 16 (0x10). Use 0x10 to make it consistent with BD70528_LDO_VOLTS.
Also remove redundant defines for BD70528_BUCK_VOLTS.
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.
Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When constructing ICMP response messages, the kernel will try to pick a
suitable source address for the outgoing packet. However, if no IPv4
addresses are configured on the system at all, this will fail and we end up
producing an ICMP message with a source address of 0.0.0.0. This can happen
on a box routing IPv4 traffic via v6 nexthops, for instance.
Since 0.0.0.0 is not generally routable on the internet, there's a good
chance that such ICMP messages will never make it back to the sender of the
original packet that the ICMP message was sent in response to. This, in
turn, can create connectivity and PMTUd problems for senders. Fortunately,
RFC7600 reserves a dummy address to be used as a source for ICMP
messages (192.0.0.8/32), so let's teach the kernel to substitute that
address as a last resort if the regular source address selection procedure
fails.
Below is a quick example reproducing this issue with network namespaces:
ip netns add ns0
ip l add type veth peer netns ns0
ip l set dev veth0 up
ip a add 10.0.0.1/24 dev veth0
ip a add fc00:dead:cafe:42::1/64 dev veth0
ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2
ip -n ns0 l set dev veth0 up
ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0
ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1
ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0
ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1
tcpdump -tpni veth0 -c 2 icmp &
ping -w 1 10.1.0.1 > /dev/null
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64
IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
2 packets captured
2 packets received by filter
0 packets dropped by kernel
With this patch the above capture changes to:
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64
IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Juliusz Chroboczek <jch@irif.fr> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.
Fixes: 9f722c0978b0 ("usbnet: CDC EEM support (v5)") Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 815f62bf7427 ("[PATCH] SMP rewrite of mkiss") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: d6b6d9877878 ("be2net: use PCIe AER capability") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While unix_may_send(sk, osk) is called while osk is locked, it appears
unix_release_sock() can overwrite unix_peer() after this lock has been
released, making KCSAN unhappy.
Changing unix_release_sock() to access/change unix_peer()
before lock is released should fix this issue.
BUG: KCSAN: data-race in unix_dgram_sendmsg / unix_release_sock
write to 0xffff88810465a338 of 8 bytes by task 20852 on cpu 1:
unix_release_sock+0x4ed/0x6e0 net/unix/af_unix.c:558
unix_release+0x2f/0x50 net/unix/af_unix.c:859
__sock_release net/socket.c:599 [inline]
sock_close+0x6c/0x150 net/socket.c:1258
__fput+0x25b/0x4e0 fs/file_table.c:280
____fput+0x11/0x20 fs/file_table.c:313
task_work_run+0xae/0x130 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x156/0x190 kernel/entry/common.c:209
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:302
do_syscall_64+0x56/0x90 arch/x86/entry/common.c:57
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88810465a338 of 8 bytes by task 20888 on cpu 0:
unix_may_send net/unix/af_unix.c:189 [inline]
unix_dgram_sendmsg+0x923/0x1610 net/unix/af_unix.c:1712
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
__do_sys_sendmmsg net/socket.c:2519 [inline]
__se_sys_sendmmsg net/socket.c:2516 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff888167905400 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 20888 Comm: syz-executor.0 Not tainted 5.13.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 24803f38a5c0 ("igmp: do not remove igmp souce list info when set
link down"), the ip_mc_clear_src() in ip_mc_destroy_dev() was removed,
because it was also called in igmpv3_clear_delrec().
However, ip_mc_clear_src() called in igmpv3_clear_delrec() doesn't
release in_dev->mc_list->sources. And RCU_INIT_POINTER() assigns the
NULL to dev->ip_ptr. As a result, in_dev cannot be obtained through
inetdev_by_index() and then in_dev->mc_list->sources cannot be released
by ip_mc_del1_src() in the sock_close. Rough call sequence goes like:
So we still need to call ip_mc_clear_src() in ip_mc_destroy_dev() to free
in_dev->mc_list->sources.
Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info ...") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Chengyang Fan <cy.fan@huawei.com> Acked-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
refactor the fec_devtype, need adjust ptp driver accordingly.
Fixes: da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous commit didn't fix the bug properly. By mistake, it replaces
the pointer of the next skb in the descriptor ring instead of the current
one. As a result, the two descriptors are assigned the same SKB. The error
is seen during the iperf test when skb_put tries to insert a second packet
and exceeds the available buffer.
Fixes: c7718ee96dbc ("net: lantiq: fix memory corruption in RX ring ") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com> Fixes: 4d06dd537f95 ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind") Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).
The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.
Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.
Fixes: d39a743511cd ("ptp: validate the requested frequency adjustment.") Fixes: d94ba80ebbea ("ptp: Added a brand new class driver for ptp clocks.") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported slab-out-of-bounds Read in
qrtr_endpoint_post. The problem was in wrong
_size_ type:
if (len != ALIGN(size, 4) + hdrlen)
goto err;
If size from qrtr_hdr is 4294967293 (0xfffffffd), the result of
ALIGN(size, 4) will be 0. In case of len == hdrlen and size == 4294967293
in header this check won't fail and
skb_put_data(skb, data + hdrlen, size);
will read out of bound from data, which is hdrlen allocated block.
Fixes: 194ccc88297a ("net: qrtr: Support decoding incoming v2 packets") Reported-and-tested-by: syzbot+1917d778024161609247@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: e87ad5539343 ("netxen: support pci error handlers") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 451724c821c1 ("qlcnic: aer support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a panic in socket ioctl cmd SIOCGSKNS when NET_NS is not enabled.
The reason is that nsfs tries to access ns->ops but the proc_ns_operations
is not implemented in this case.
[7.670023] Unable to handle kernel NULL pointer dereference at virtual address 00000010
[7.670268] pgd = 32b54000
[7.670544] [00000010] *pgd=00000000
[7.671861] Internal error: Oops: 5 [#1] SMP ARM
[7.672315] Modules linked in:
[7.672918] CPU: 0 PID: 1 Comm: systemd Not tainted 5.13.0-rc3-00375-g6799d4f2da49 #16
[7.673309] Hardware name: Generic DT based system
[7.673642] PC is at nsfs_evict+0x24/0x30
[7.674486] LR is at clear_inode+0x20/0x9c
The same to tun SIOCGSKNS command.
To fix this problem, we make get_net_ns() return -EINVAL when NET_NS is
disabled. Meanwhile move it to right place net/core/net_namespace.c.
Signed-off-by: Changbin Du <changbin.du@gmail.com> Fixes: c62cce2caee5 ("net: add an ioctl to get a socket network namespace") Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Christian Brauner <christian.brauner@ubuntu.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The register starts from 0x800 is the 16th MAC address register rather
than the first one.
Fixes: cffb13f4d6fb ("stmmac: extend mac addr reg and fix perfect filering") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: ab69bde6b2e9 ("alx: add a simple AR816x/AR817x device driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TCP option parser in cake qdisc (cake_get_tcpopt and
cake_tcph_may_drop) could read one byte out of bounds. When the length
is 1, the execution flow gets into the loop, reads one byte of the
opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads
one more byte, which exceeds the length of 1.
This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack
out of bounds when parsing TCP options.").
v2 changes:
Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP
header. Although it wasn't strictly an out-of-bounds access (memory was
allocated), garbage values could be read where CAKE expected the TCP
header if doff was smaller than 5.
Cc: Young Xiao <92siuyang@gmail.com> Fixes: 8b7138814f29 ("sch_cake: Add optional ACK filter") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TCP option parser in synproxy (synproxy_parse_options) could read
one byte out of bounds. When the length is 1, the execution flow gets
into the loop, reads one byte of the opcode, and if the opcode is
neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds
the length of 1.
This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack
out of bounds when parsing TCP options.").
v2 changes:
Added an early return when length < 0 to avoid calling
skb_header_pointer with negative length.
Cc: Young Xiao <92siuyang@gmail.com> Fixes: 48b1de4c110a ("netfilter: add SYNPROXY core/target") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device is able to offload either the outer header csum or inner
header csum. The driver utilizes the inner csum offload. Hence, block
setting of tx-udp_tnl-csum-segmentation and set it to off[fixed].
Fixes: b49663c8fb49 ("net/mlx5e: Add support for UDP tunnel segmentation with outer checksum offload") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log