Stephen Boyd [Thu, 18 Oct 2018 22:39:08 +0000 (15:39 -0700)]
Merge branches 'clk-mvebu-periph-pm', 'clk-meson', 'clk-allwinner', 'clk-mvebu-dup' and 'clk-davinci' into clk-next
- S2RAM support for Marvell mvebu periph clks
* clk-mvebu-periph-pm:
clk: mvebu: armada-37xx-periph: add suspend/resume support
clk: mvebu: armada-37xx-periph: save the IP base address in the driver data
* clk-meson:
clk: meson: meson8b: use the regmap in the internal reset controller
clk: meson: meson8b: register the clock controller early
clk: meson-axg: pcie: drop the mpll3 clock parent
clk: meson: axg: round audio system master clocks down
clk: meson: clk-pll: drop hard-coded rates from pll tables
clk: meson: clk-pll: remove od parameters
clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
clk: meson: clk-pll: add enable bit
* clk-allwinner:
dt-bindings: clock: sun50i-a64-ccu: Add PLL_VIDEO0 macro
clk: sunxi-ng: a64: Add max. rate constraint to video PLLs
clk: sunxi-ng: a64: Add minimal rate for video PLLs
clk: sunxi-ng: sun50i: h6: Add 2x fixed post-divider to MMC module clocks
clk: sunxi-ng: a83t: Add max. rate constraint to video PLLs
clk: sunxi-ng: nkmp: Add constraint for maximum rate
clk: sunxi-ng: r40: Add max. rate constraint to video PLLs
clk: sunxi-ng: h3/h5: Add max. rate constraint to pll-video
clk: sunxi-ng: Add maximum rate constraint to NM PLLs
clk: sunxi-ng: h6: fix PWM gate/reset offset
clk: sunxi-ng: h6: fix bus clocks' divider position
Stephen Boyd [Thu, 18 Oct 2018 22:33:28 +0000 (15:33 -0700)]
Merge branches 'clk-spdx', 'clk-qcom-dfs', 'clk-smp2s11-include', 'clk-qcom-8996-missing' and 'clk-qcom-qspi' into clk-next
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
* clk-spdx:
clk: mvebu: use SPDX-License-Identifier
clk: renesas: Convert to SPDX identifiers
clk: renesas: use SPDX identifier for Renesas drivers
clk: s2mps11,s3c64xx: Add SPDX license identifiers
clk: max77686: Add SPDX license identifiers
* clk-qcom-dfs:
clk: qcom: Allocate space for NULL terimation in DFS table
clk: qcom: gcc: Register QUPv3 RCGs for DFS on SDM845
clk: qcom: Add support for RCG to register for DFS
* clk-smp2s11-include:
clk: s2mps11: Use existing defines from bindings for clock IDs
* clk-qcom-8996-missing:
clk: qcom: Add some missing gcc clks for msm8996
* clk-qcom-qspi:
clk: qcom: Add qspi (Quad SPI) clocks for sdm845
clk: qcom: Add qspi (Quad SPI) clock defines for sdm845 to header
Gregory CLEMENT [Wed, 10 Oct 2018 18:18:38 +0000 (20:18 +0200)]
clk: mvebu: armada-37xx-tbg: Switch to clk_get and balance it in probe
The parent clock is get only to have its name, and then the clock is no
more used, so we can safely free it using clk_put. Furthermore as between
the successful devm_clk_get() and the devm_clk_put() call we don't exit
the probe function in error so I can use non managed version of clk_get()
and clk_put().
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Arnd Bergmann [Fri, 5 Oct 2018 16:11:15 +0000 (18:11 +0200)]
clk: keystone: add missing MODULE_LICENSE
A randconfig build showed that two clk modules have no license tag:
WARNING: modpost: missing MODULE_LICENSE() in drivers/clk/keystone/gate.o
see include/linux/module.h for more information
WARNING: modpost: missing MODULE_LICENSE() in drivers/clk/keystone/pll.o
see include/linux/module.h for more information
Add the appropriate information from the comment at the start of the
two files.
While applying the commit a8309cedcdce ("clk: apn806: Add eMMC clock to
system controller driver"), of_clk_add_provider was added wheres it was
already present in the probe function.
This extraneous call is harmless but not useful so remove it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stephen Boyd [Mon, 1 Oct 2018 17:56:17 +0000 (10:56 -0700)]
Merge tag 'clk-renesas-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Add support for the new RZ/A2 (R7S9210) SoC, including early clock
support for the Renesas CPG/MSSR driver
- Add support for the new RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Convert DT binding includes to SPDX license identifiers
* tag 'clk-renesas-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r7s9210: Add SPI clocks
clk: renesas: r7s9210: Move table update to separate function
clk: renesas: r7s9210: Convert some clocks to early
clk: renesas: cpg-mssr: Add early clock support
clk: renesas: r8a77970: Add TPU clock
clk: renesas: r8a77990: Fix incorrect PLL0 divider in comment
dt-bindings: clock: renesas: cpg-mssr: Document r8a774c0
clk: renesas: cpg-mssr: Add r8a774c0 support
clk: renesas: Add r8a774c0 CPG Core Clock Definitions
clk: renesas: r8a7743: Add r8a7744 support
clk: renesas: Add r8a7744 CPG Core Clock Definitions
dt-bindings: clock: renesas: cpg-mssr: Document r8a7744 binding
dt-bindings: clock: renesas: Convert to SPDX identifiers
clk: renesas: cpg-mssr: Add R7S9210 support
clk: renesas: r8a77970: Add TMU clocks
clk: renesas: r8a77970: Add CMT clocks
clk: renesas: r9a06g032: Fix UART34567 clock rate
clk: renesas: r8a77970: Add SD0H/SD0 clocks for SDHI
clk: renesas: r8a77980: Add CMT clocks
Stephen Boyd [Mon, 1 Oct 2018 17:32:32 +0000 (10:32 -0700)]
Merge tag 'meson-clk-4.20-1' of https://github.com/BayLibre/clk-meson into clk-meson
Pull meson clk driver updates from Jerome Brunet:
- clk-pll driver improvements and updates
- add axg audio controller system clocks
- drop mpll3 from the possible pcie clock parent of the axg
- register meson8b clock controller early
* tag 'meson-clk-4.20-1' of https://github.com/BayLibre/clk-meson:
clk: meson: meson8b: use the regmap in the internal reset controller
clk: meson: meson8b: register the clock controller early
clk: meson-axg: pcie: drop the mpll3 clock parent
clk: meson: axg: round audio system master clocks down
clk: meson: clk-pll: drop hard-coded rates from pll tables
clk: meson: clk-pll: remove od parameters
clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
clk: meson: clk-pll: add enable bit
Chris Brandt [Mon, 24 Sep 2018 16:49:35 +0000 (11:49 -0500)]
clk: renesas: cpg-mssr: Add early clock support
Add support for SoCs that need to register core and module clocks early in
order to use OF drivers that exclusively use macros such as
TIMER_OF_DECLARE.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Martin Blumenstingl [Sat, 21 Jul 2018 19:14:00 +0000 (21:14 +0200)]
clk: meson: meson8b: use the regmap in the internal reset controller
For now the reset controller was using raw register access because the
early init did not initialize the regmap. However, now that clocks are
initialized early we can simply use the regmap also for the reset
controller.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Martin Blumenstingl [Sat, 21 Jul 2018 19:13:59 +0000 (21:13 +0200)]
clk: meson: meson8b: register the clock controller early
Until now only the reset controller (part of the clock controller
register space) was registered early in the boot process, while the
clock controller itself was registered later on.
However, some parts of the SoC are initialized early in the boot process,
such as the SRAM and the TWD timer. The bootloader already enables these
clocks so we didn't see any issues so far.
Register the clock controller early so other drivers (such as the SRAM
and TWD timer) can use the clocks early in the boot process.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Jerome Brunet [Wed, 1 Aug 2018 14:07:32 +0000 (16:07 +0200)]
clk: meson: axg: round audio system master clocks down
Some of the master clocks provided by the axg audio clock controller are
system clock (spdifin and pdm sysclk). They are used to clock an internal
DSP of the related devices. Having them constantly rounded down instead
of closest is preferable.
Jerome Brunet [Wed, 1 Aug 2018 14:00:53 +0000 (16:00 +0200)]
clk: meson: clk-pll: drop hard-coded rates from pll tables
Putting hard-coded rates inside the parameter tables assumes that
the parent is known and will never change. That's a big assumption
we should not make.
We have everything we need to recalculate the output rate using
the parent rate and the rest of the parameters. Let's do so and
drop the rates from the tables.
Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Jerome Brunet [Wed, 1 Aug 2018 14:00:52 +0000 (16:00 +0200)]
clk: meson: clk-pll: remove od parameters
Remove od parameters from pll clocks and add post dividers clocks
instead. Some clock, especially the one which feature several ods,
may provide output between those ods. Also, some drivers, such
as the hdmi driver, may require a more detailed control of the
clock dividers, compared to what CCF would perform automatically.
One added benefit of removing ods is that it also greatly reduce the
size of the rate parameter tables.
In the future, we could possibly take the predivider 'n' out of this
driver as well. To do so, we will need to understand the constraints
for the PLL to lock and whether or not it depends on the input clock
rate.
Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Jerome Brunet [Wed, 1 Aug 2018 14:00:51 +0000 (16:00 +0200)]
clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary
CLK_GET_RATE_NOCACHE should only be necessary when the registers
controlling the rate of clock may change outside of CCF. On Amlogic,
it should only be the case for the hdmi pll which is directly controlled
by the display driver (WIP to fix this).
The other plls should not require this flag.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Jerome Brunet [Wed, 1 Aug 2018 14:00:50 +0000 (16:00 +0200)]
clk: meson: clk-pll: add enable bit
Add the enable the bit of the pll clocks.
These pll clocks may be disabled but we can't model this as an external
gate since the pll needs to lock when enabled.
Adding this bit allows to drop the poke of the first register of PLL.
This will be useful to model the different components of the pll using
generic clocks elements
Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add all RZ/G2E (a.k.a. R8A774C0) Clock Pulse Generator Core
Clock Outputs, as listed in Table 8.2g ("List of Clocks
[RZ/G2E]") of the RZ/G2 Hardware User's Manual.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Chris Brandt [Fri, 7 Sep 2018 16:58:49 +0000 (11:58 -0500)]
clk: renesas: cpg-mssr: Add R7S9210 support
Add support for the R7S9210 (RZ/A2) Clock Pulse Generator and Module
Standby.
The Module Standby HW in the RZ/A series is very close to R-Car HW, except
for how the registers are laid out.
The MSTP registers are only 8-bits wide, there are no status registers
(MSTPSR), and the register offsets are a little different. Since the RZ/A
hardware manuals refer to these registers as the Standby Control Registers,
we'll use that name to distinguish the RZ/A type from the R-Car type.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Acked-by: Rob Herring <robh@kernel.org> # DT bits Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Phil Edworthy [Fri, 31 Aug 2018 11:26:36 +0000 (12:26 +0100)]
clk: renesas: r9a06g032: Fix UART34567 clock rate
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.
In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.
This change stops the UART34567 clock rate from changing for the same
reasons.
clk: sunxi-ng: a64: Add max. rate constraint to video PLLs
Video PLLs on A64 can be set to higher rate that it is actually
supported by HW.
Limit maximum rate to 1008 MHz. This is the maximum allowed rate by BSP
clock driver. Interestengly, user manual specifies maximum frequency to
be 600 MHz. Historically, this data was wrong in some user manuals for
other SoCs, so more faith is put in BSP clock driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the H6, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
This patch adds the post-dividers to the MMC clocks, following the
approach on A64.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU") Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Sergei Shtylyov [Sat, 1 Sep 2018 20:12:28 +0000 (23:12 +0300)]
clk: renesas: r8a77970: Add SD0H/SD0 clocks for SDHI
On R-Car V3M (AKA R8A77970), the SD0CKCR is laid out differently than on
the other R-Car gen3 SoCs. In fact, the layout is the same as on R-Car gen2
SoCs, so we'll need to copy the divisor tables from the R-Car gen2 driver.
We'll also need to support the SoC specific clock types, thus we're adding
CLK_TYPE_GEN3_SOC_BASE at the end of 'enum rcar_gen3_clk_types', declare
SD0H/SDH clocks in 'enum r8a77970_clk_types', and handle those clocks in
the overridden cpg_clk_register() method; then, finally, add the SD-IF
module clock (derived from the SD0 clock).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
clk: mvebu: armada-37xx-periph: add suspend/resume support
Add suspend/resume hooks in Armada 37xx peripheral clocks driver to
handle S2RAM operations.
One can think that these hooks are useless by comparing the register
values before and after a suspend/resume cycle: they will look the same
anyway. This is because of some scripts executed by the Cortex-M3 core
during ATF operations to init both the clocks and the DDR. These values
could be modified by the BL33 stage or by Linux itself and should be
preserved.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk: mvebu: armada-37xx-periph: save the IP base address in the driver data
Prepare the introduction of suspend/resume hooks by having an easy way
to access all the registers in one go just from a device: add the IP
base address in the driver data.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is a potential execution path in which function
platform_get_resource() returns NULL. If this happens,
we will end up having a NULL pointer dereference.
Fix this by replacing devm_ioremap with devm_ioremap_resource,
which has the NULL check and the memory region request.
This code was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org Fixes: 97b7129cd2af ("reset: hisilicon: change the definition of hisi_reset_init") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stephen Boyd [Fri, 31 Aug 2018 17:13:53 +0000 (10:13 -0700)]
Merge tag 'clk-renesas-for-v4.20-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs,
- Add support for SATA and Fine Display Processor (FDP) clocks on
R-Car M3-N,
- Add support for the new RZ/G2M (r8a774a1) SoC,
- Small fixes and clean ups.
* tag 'clk-renesas-for-v4.20-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a77990: Add missing I2C7 clock
clk: renesas: r8a77965: Add FDP clock
clk: renesas: cpg-mssr: Add r8a774a1 support
clk: renesas: Add r8a774a1 CPG Core Clock Definitions
clk: renesas: r8a77965: Add SATA clock
clk: renesas: r8a77980: Add RCLK for watchdog timer
clk: renesas: rcar-gen3: Add support for mode pin clock selection
clk: renesas: r8a77995: Correct RCLK handling
clk: renesas: r8a77990: Correct RCLK handling
clk: renesas: rcar-gen3: Add support for RCKSEL clock selection
clk: renesas: cpg-mssr: Add support for fixed rate clocks
clk: renesas: r8a77980: Add OSC predivider configuration and clock
clk: renesas: r8a77965: Add OSC EXTAL predivider configuration
clk: renesas: r8a7796: Add OSC EXTAL predivider configuration
clk: renesas: r8a7795: Add OSC EXTAL predivider configuration
clk: renesas: rcar-gen3: Add support for OSC EXTAL predivider
clk: renesas: rcar-gen3: Rename rint to .r
Douglas Anderson [Thu, 30 Aug 2018 17:34:37 +0000 (10:34 -0700)]
clk: qcom: Allocate space for NULL terimation in DFS table
The table allocated in clk_rcg2_dfs_populate_freq_table() is
eventually iterated over by qcom_find_freq() which assumes that the
table is NULL terminated. Allocate one extra space in the array for
the NULL termination. Initting of the NULL termination is implicit
due to kcalloc().
Fixes: cc4f6944d0e3 ("clk: qcom: Add support for RCG to register for DFS") Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Johan Hovold [Wed, 22 Aug 2018 09:03:19 +0000 (11:03 +0200)]
clk: ti: fix OF child-node lookup
Fix child-node lookup which by using the wrong OF helper was searching
the whole tree depth-first, something which could end up matching an
unrelated node.
Also fix the related node-reference leaks.
Fixes: 5b385a45e001 ("clk: ti: add support for clkctrl aliases") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Douglas Anderson [Tue, 24 Jul 2018 17:45:12 +0000 (10:45 -0700)]
clk: qcom: Add qspi (Quad SPI) clock defines for sdm845 to header
These clocks will need to be defined in the clock driver and
referenced in device tree files.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Taniya Das <tdas@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Krzysztof Kozlowski [Tue, 7 Aug 2018 16:17:13 +0000 (18:17 +0200)]
clk: s2mps11: Use existing defines from bindings for clock IDs
The clock IDs must match between DeviceTree bindings and the driver.
There is already a header file used by DeviceTree sources so include it
in the driver to remove duplicated symbols.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Taniya Das [Sat, 11 Aug 2018 01:53:56 +0000 (07:23 +0530)]
clk: qcom: gcc: Register QUPv3 RCGs for DFS on SDM845
QUPv3 clocks support DFS and thus register the RCGs which require support
for the same.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Use new macro, split out init structures so they
don't have to be copied] Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Taniya Das [Sat, 11 Aug 2018 01:53:55 +0000 (07:23 +0530)]
clk: qcom: Add support for RCG to register for DFS
Dynamic Frequency switch is a feature of clock controller by which request
from peripherals allows automatic switching frequency of input clock
without SW intervention. There are various performance levels associated
with a root clock. When the input performance state changes, the source
clocks and division ratios of the new performance state are loaded on to
RCG via HW and the RCG switches to new clock frequency when the RCG is in
DFS HW enabled mode.
Register the root clock generators(RCG) to switch to use the dfs clock ops
in the cases where DFS is enabled. The clk_round_rate() called by the clock
consumer would invoke the dfs determine clock ops and would read the DFS
performance level registers to identify all the frequencies supported and
update the frequency table. The DFS clock consumers would maintain these
frequency mapping and request the desired performance levels.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Rework registration logic to stop copying, change
recalc_rate() to index directly into the table if possible and fallback
to calculating on the fly with an assumed correct parent] Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk: renesas: rcar-gen3: Add support for mode pin clock selection
Make the existing support for selecting between clean and SSCG clocks
using MD12 more generic, to allow using other mode pins for arbitrary
clock selection.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car D3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car E3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
clk: renesas: r8a77980: Add OSC predivider configuration and clock
R-Car Gen3 Hardware Manual Rev.0.54 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC clock. Hence augment the configuration structure with all
documented predivider values.
Add the OSC clock using the configured predivider.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car M3-N does not
have the CPG_RCKCR register. Change the OSC and RINT clock definitions
to use the OSC EXTAL predivider instead, which is supported on all R-Car
M3-N SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car M3-W ES1.1. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car M3-W SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car H3 ES2.0. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car H3 SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Jernej Skrabec [Thu, 9 Aug 2018 16:52:17 +0000 (18:52 +0200)]
clk: sunxi-ng: a83t: Add max. rate constraint to video PLLs
It may happen that clock framework finds optimal video PLL rate above
that which is really supported by HW.
User manual doesn't really say what is upper limit for video PLLs on
A83T. Because of that, use the maximum rate defined in BSP clk driver
which is 3 GHz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Jernej Skrabec [Thu, 9 Aug 2018 16:52:15 +0000 (18:52 +0200)]
clk: sunxi-ng: r40: Add max. rate constraint to video PLLs
Video PLLs on R40 can be set to higher rate that it is actually
supported by HW.
Limit maximum rate to 1008 MHz. This is the maximum allowed rate by BSP
clock driver. Interestengly, user manual specifies maximum frequency to
be 600 MHz. Historically, this data was wrong in some user manuals for
other SoCs, so more faith is put in BSP clock driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Jernej Skrabec [Thu, 9 Aug 2018 16:52:14 +0000 (18:52 +0200)]
clk: sunxi-ng: h3/h5: Add max. rate constraint to pll-video
As it turns out, pll-video can be set to higher rate that it is really
supported by HW.
For example, one monitor requested 185.58 MHz pixel clock. Clock
framework calculated that minimum rate error would be when pll-video
is set to 2040 MHz. This is clearly out of specs.
Both H3 and H5 user manuals specify 600 MHz as maximum supported rate.
However, BSP clock drivers allow up to 912 MHz and 1008 MHz
respectively. Here 912 MHz is chosen because user manuals were already
proven wrong once for lower limits.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Icenowy Zheng [Wed, 8 Aug 2018 17:19:52 +0000 (01:19 +0800)]
clk: sunxi-ng: h6: fix bus clocks' divider position
The bus clocks (AHB/APB) on Allwinner H6 have their second divider start
at bit 8, according to the user manual and the BSP code. However,
currently the divider offset is incorrectly set to 16, thus the divider
is not correctly read and the clock frequency is not correctly calculated.
Fix this bit offset on all affected bus clocks in ccu-sun50i-h6.
Linus Torvalds [Sun, 26 Aug 2018 20:39:05 +0000 (13:39 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer update from Thomas Gleixner:
"New defines for the compat time* types so they can be shared between
32bit and 64bit builds. Not used yet, but merging them now allows the
actual conversions to be merged through different maintainer trees
without dependencies
We still have compat interfaces for 32bit on 64bit even with the new
2038 safe timespec/val variants because pointer size is different. And
for the old style timespec/val interfaces we need yet another 'compat'
interface for both 32bit native and 32bit on 64bit"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
y2038: Provide aliases for compat helpers
Linus Torvalds [Sun, 26 Aug 2018 18:48:42 +0000 (11:48 -0700)]
Merge branch 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
Linus Torvalds [Sun, 26 Aug 2018 18:41:08 +0000 (11:41 -0700)]
Merge tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin fix from Kees Cook:
"Lift gcc test into Kconfig. This is for better behavior when the
kernel is built with Clang, reported by Stefan Agner"
* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Disable when building under Clang
Linus Torvalds [Sun, 26 Aug 2018 18:25:21 +0000 (11:25 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Kernel:
- Improve kallsyms coverage
- Add x86 entry trampolines to kcore
- Fix ARM SPE handling
- Correct PPC event post processing
Tools:
- Make the build system more robust
- Small fixes and enhancements all over the place
- Update kernel ABI header copies
- Preparatory work for converting libtraceevnt to a shared library
- License cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
tools arch x86: Update tools's copy of cpufeatures.h
perf python: Fix pyrf_evlist__read_on_cpu() interface
perf mmap: Store real cpu number in 'struct perf_mmap'
perf tools: Remove ext from struct kmod_path
perf tools: Add gzip_is_compressed function
perf tools: Add lzma_is_compressed function
perf tools: Add is_compressed callback to compressions array
perf tools: Move the temp file processing into decompress_kmodule
perf tools: Use compression id in decompress_kmodule()
perf tools: Store compression id into struct dso
perf tools: Add compression id into 'struct kmod_path'
perf tools: Make is_supported_compression() static
perf tools: Make decompress_to_file() function static
perf tools: Get rid of dso__needs_decompress() call in __open_dso()
perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble()
perf tools: Get rid of dso__needs_decompress() call in read_object_code()
tools lib traceevent: Change to SPDX License format
perf llvm: Allow passing options to llc in addition to clang
perf parser: Improve error message for PMU address filters
...
Linus Torvalds [Sun, 26 Aug 2018 17:13:21 +0000 (10:13 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Correct the L1TF fallout on 32bit and the off by one in the 'too much
RAM for protection' calculation.
- Add a helpful kernel message for the 'too much RAM' case
- Unbreak the VDSO in case that the compiler desides to use indirect
jumps/calls and emits retpolines which cannot be resolved because the
kernel uses its own thunks, which does not work for the VDSO. Make it
use the builtin thunks.
- Re-export start_thread() which was unexported when the 32/64bit
implementation was unified. start_thread() is required by modular
binfmt handlers.
- Trivial cleanups
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/l1tf: Suggest what to do on systems with too much RAM
x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
x86/kvm/vmx: Remove duplicate l1d flush definitions
x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
x86/process: Re-export start_thread()
x86/mce: Add notifier_block forward declaration
x86/vdso: Fix vDSO build if a retpoline is emitted
Linus Torvalds [Sun, 26 Aug 2018 16:55:28 +0000 (09:55 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Linus Torvalds [Sun, 26 Aug 2018 16:47:00 +0000 (09:47 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull licking update from Thomas Gleixner:
"Mark the switch cases which fall through to the next case with the
proper comment so the fallthrough compiler checks can be enabled"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Mark expected switch fall-throughs
projects / users / jedix / linux-maple.git / log