Yu Zhao [Wed, 8 Jan 2025 07:48:21 +0000 (00:48 -0700)]
mm/hugetlb_vmemmap: fix memory loads ordering
Using x86_64 as an example, for a 32KB struct page[] area describing a 2MB
hugeTLB, HVO reduces the area to 4KB by the following steps:
1. Split the (r/w vmemmap) PMD mapping the area into 512 (r/w) PTEs;
2. For the 8 PTEs mapping the area, remap PTE 1-7 to the page mapped
by PTE 0, and at the same time change the permission from r/w to
r/o;
3. Free the pages PTE 1-7 used to map, hence the reduction from 32KB
to 4KB.
However, the following race can happen due to improperly memory loads
ordering:
CPU 1 (HVO) CPU 2 (speculative PFN walker)
atomic_add_unless(&page->_refcount)
XXX: try to modify r/o struct page[]
Specifically, page_is_fake_head() must be ordered after page_ref_count()
on CPU 2 so that it can only return true for this case, to avoid the later
attempt to modify r/o struct page[].
This patch adds the missing memory barrier and makes the tests on
page_is_fake_head() and page_ref_count() done in the proper order.
Link: https://lkml.kernel.org/r/20250108074822.722696-1-yuzhao@google.com Fixes: bd225530a4c7 ("mm/hugetlb_vmemmap: fix race with speculative PFN walkers") Signed-off-by: Yu Zhao <yuzhao@google.com> Reported-by: Will Deacon <will@kernel.org> Closes: https://lore.kernel.org/20241128142028.GA3506@willie-the-truck/ Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Muchun Song <muchun.song@linux.dev> Cc: Mateusz Guzik <mjguzik@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
liuye [Tue, 19 Nov 2024 06:08:42 +0000 (14:08 +0800)]
mm/vmscan: fix hard LOCKUP in function isolate_lru_folios
This fixes the following hard lockup in isolate_lru_folios() during memory
reclaim. If the LRU mostly contains ineligible folios this may trigger
watchdog.
watchdog: Watchdog detected hard LOCKUP on cpu 173
RIP: 0010:native_queued_spin_lock_slowpath+0x255/0x2a0
Call Trace:
_raw_spin_lock_irqsave+0x31/0x40
folio_lruvec_lock_irqsave+0x5f/0x90
folio_batch_move_lru+0x91/0x150
lru_add_drain_per_cpu+0x1c/0x40
process_one_work+0x17d/0x350
worker_thread+0x27b/0x3a0
kthread+0xe8/0x120
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1b/0x30
Scenario:
User processe are requesting a large amount of memory and keep page active.
Then a module continuously requests memory from ZONE_DMA32 area.
Memory reclaim will be triggered due to ZONE_DMA32 watermark alarm reached.
However pages in the LRU(active_anon) list are mostly from
the ZONE_NORMAL area.
About the Fixes:
Why did it take eight years to be discovered?
The problem requires the following conditions to occur:
1. The device memory should be large enough.
2. Pages in the LRU(active_anon) list are mostly from the ZONE_NORMAL area.
3. The memory in ZONE_DMA32 needs to reach the watermark.
If the memory is not large enough, or if the usage design of ZONE_DMA32
area memory is reasonable, this problem is difficult to detect.
notes:
The problem is most likely to occur in ZONE_DMA32 and ZONE_NORMAL,
but other suitable scenarios may also trigger the problem.
Link: https://lkml.kernel.org/r/20241119060842.274072-1-liuye@kylinos.cn Fixes: b2e18757f2c9 ("mm, vmscan: begin reclaiming pages on a per-node basis") Signed-off-by: liuye <liuye@kylinos.cn> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Yang Shi <yang@os.amperecomputing.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Su Yue [Mon, 6 Jan 2025 14:06:40 +0000 (22:06 +0800)]
ocfs2: check dir i_size in ocfs2_find_entry
syz reports an out of bounds read:
==================================================================
BUG: KASAN: slab-out-of-bounds in ocfs2_match fs/ocfs2/dir.c:334
[inline]
BUG: KASAN: slab-out-of-bounds in ocfs2_search_dirblock+0x283/0x6e0
fs/ocfs2/dir.c:367
Read of size 1 at addr ffff88804d8b9982 by task syz-executor.2/14802
The two reports are all caused invalid negative i_size of dir inode. For
ocfs2, dir_inode can't be negative or zero.
Here add a check in which is called by ocfs2_check_dir_for_entry(). It
fixes the second report as ocfs2_check_dir_for_entry() must be called
before ocfs2_prepare_dir_for_insert(). Also set a up limit for dir with
OCFS2_INLINE_DATA_FL. The i_size can't be great than blocksize.
Yosry Ahmed [Mon, 13 Jan 2025 21:44:58 +0000 (21:44 +0000)]
mm: zswap: move allocations during CPU init outside the lock
In zswap_cpu_comp_prepare(), allocations are made and assigned to various
members of acomp_ctx under acomp_ctx->mutex. However, allocations may
recurse into zswap through reclaim, trying to acquire the same mutex and
deadlocking.
Move the allocations before the mutex critical section. Only the
initialization of acomp_ctx needs to be done with the mutex held.
Link: https://lkml.kernel.org/r/20250113214458.2123410-1-yosryahmed@google.com Fixes: 12dcb0ef5406 ("mm: zswap: properly synchronize freeing resources during CPU hotunplug") Signed-off-by: Yosry Ahmed <yosryahmed@google.com> Reviewed-by: Chengming Zhou <chengming.zhou@linux.dev> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Nhat Pham <nphamcs@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This indicates that the pgoff is unaligned. After analysis, I confirm the
vma is mapped to /dev/zero. Such a vma certainly has vm_file, but it is
set to anonymous by mmap_zero(). So even if it's mmapped by 2m-unaligned,
it can pass the check in thp_vma_allowable_order() as it is an
anonymous-mmap, but then be collapsed as a file-mmap.
It seems the problem has existed for a long time, but actually, since we
have khugepaged_max_ptes_none check before, we will skip collapse it as it
is /dev/zero and so has no present page. But commit d8ea7cc8547c limit
the check for only khugepaged, so the BUG_ON() can be triggered by
madvise_collapse().
Add vma_is_anonymous() check to make such vma be processed by
hpage_collapse_scan_pmd().
Link: https://lkml.kernel.org/r/20250111034511.2223353-1-liushixin2@huawei.com Fixes: d8ea7cc8547c ("mm/khugepaged: add flag to predicate khugepaged-only behavior") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Reviewed-by: Yang Shi <yang@os.amperecomputing.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Chengming Zhou <chengming.zhou@linux.dev> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Mattew Wilcox <willy@infradead.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nanyong Sun <sunnanyong@huawei.com> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
zihan zhou [Wed, 25 Dec 2024 02:10:35 +0000 (10:10 +0800)]
mm: page_alloc: fix missed updates of lowmem_reserve in adjust_managed_page_count
In the kernel, the zone's lowmem_reserve and _watermark, and the global
variable 'totalreserve_pages' depend on the value of managed_pages, but
after running adjust_managed_page_count, these values aren't updated,
which causes some problems.
For example, in a system with six 1GB large pages, we found that the value
of protection in zoneinfo (zone->lowmem_reserve), is not right. Its value
seems to be calculated from the initial managed_pages, but after the
managed_pages changed, was not updated. Only after reading the file
/proc/sys/vm/lowmem_reserve_ratio, updates happen.
lowmem_reserve increased also makes the totalreserve_pages increased,
which causes a decrease in available memory. The one above is just a test
machine, and the increase is not significant. On our online machine, the
reserved memory will increase by several GB due to reading this file. It
is clearly unreasonable to cause a sharp drop in available memory just by
reading a file.
In this patch, we update reserve memory when update managed_pages, The
size of reserved memory becomes stable. But it seems that the _watermark
should also be updated along with the managed_pages. We have not done it
because we are unsure if it is reasonable to set the watermark through the
initial managed_pages. If it is not reasonable, we will propose new
patch.
Rik van Riel [Fri, 10 Jan 2025 15:28:21 +0000 (10:28 -0500)]
fs/proc: fix softlockup in __read_vmcore (part 2)
Since commit 5cbcb62dddf5 ("fs/proc: fix softlockup in __read_vmcore") the
number of softlockups in __read_vmcore at kdump time have gone down, but
they still happen sometimes.
In a memory constrained environment like the kdump image, a softlockup is
not just a harmless message, but it can interfere with things like RCU
freeing memory, causing the crashdump to get stuck.
The second loop in __read_vmcore has a lot more opportunities for natural
sleep points, like scheduling out while waiting for a data write to
happen, but apparently that is not always enough.
Add a cond_resched() to the second loop in __read_vmcore to (hopefully)
get rid of the softlockups.
Link: https://lkml.kernel.org/r/20250110102821.2a37581b@fangorn Fixes: 5cbcb62dddf5 ("fs/proc: fix softlockup in __read_vmcore") Signed-off-by: Rik van Riel <riel@surriel.com> Reported-by: Breno Leitao <leitao@debian.org> Cc: Baoquan He <bhe@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Matthew Wilcox (Oracle) [Fri, 10 Jan 2025 16:32:57 +0000 (16:32 +0000)]
mm: fix assertion in folio_end_read()
We only need to assert that the uptodate flag is clear if we're going to
set it. This hasn't been a problem before now because we have only used
folio_end_read() when completing with an error, but it's convenient to use
it in squashfs if we discover the folio is already uptodate.
Donet Tom [Thu, 9 Jan 2025 06:05:39 +0000 (00:05 -0600)]
mm: vmscan : pgdemote vmstat is not getting updated when MGLRU is enabled.
When MGLRU is enabled, the pgdemote_kswapd, pgdemote_direct, and
pgdemote_khugepaged stats in vmstat are not being updated.
Commit f77f0c751478 ("mm,memcg: provide per-cgroup counters for NUMA
balancing operations") moved the pgdemote vmstat update from
demote_folio_list() to shrink_inactive_list(), which is in the normal LRU
path. As a result, the pgdemote stats are updated correctly for the
normal LRU but not for MGLRU.
To address this, we have added the pgdemote stat update in the
evict_folios() function, which is in the MGLRU path. With this patch, the
pgdemote stats will now be updated correctly when MGLRU is enabled.
Without this patch vmstat output when MGLRU is enabled
======================================================
pgdemote_kswapd 0
pgdemote_direct 0
pgdemote_khugepaged 0
With this patch vmstat output when MGLRU is enabled
===================================================
pgdemote_kswapd 43234
pgdemote_direct 4691
pgdemote_khugepaged 0
Link: https://lkml.kernel.org/r/20250109060540.451261-1-donettom@linux.ibm.com Fixes: f77f0c751478 ("mm,memcg: provide per-cgroup counters for NUMA balancing operations") Signed-off-by: Donet Tom <donettom@linux.ibm.com> Acked-by: Yu Zhao <yuzhao@google.com> Tested-by: Li Zhijian <lizhijian@fujitsu.com> Reviewed-by: Li Zhijian <lizhijian@fujitsu.com> Cc: Aneesh Kumar K.V (Arm) <aneesh.kumar@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kaiyang Zhao <kaiyang2@cs.cmu.edu> Cc: Michal Hocko <mhocko@kernel.org> Cc: Muchun Song <muchun.song@linux.dev> Cc: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Shakeel Butt <shakeel.butt@linux.dev> Cc: Wei Xu <weixugc@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Koichiro Den [Wed, 8 Jan 2025 04:28:07 +0000 (13:28 +0900)]
vmstat: disable vmstat_work on vmstat_cpu_down_prep()
The upstream commit adcfb264c3ed ("vmstat: disable vmstat_work on
vmstat_cpu_down_prep()") introduced another warning during the boot phase
so was soon reverted on upstream by commit cd6313beaeae ("Revert "vmstat:
disable vmstat_work on vmstat_cpu_down_prep()""). This commit resolves it
and reattempts the original fix.
Even after mm/vmstat:online teardown, shepherd may still queue work for
the dying cpu until the cpu is removed from online mask. While it's quite
rare, this means that after unbind_workers() unbinds a per-cpu kworker, it
potentially runs vmstat_update for the dying CPU on an irrelevant cpu
before entering atomic AP states. When CONFIG_DEBUG_PREEMPT=y, it results
in the following error with the backtrace.
BUG: using smp_processor_id() in preemptible [00000000] code: \
kworker/7:3/1702
caller is refresh_cpu_vm_stats+0x235/0x5f0
CPU: 0 UID: 0 PID: 1702 Comm: kworker/7:3 Tainted: G
Tainted: [N]=TEST
Workqueue: mm_percpu_wq vmstat_update
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xb0
check_preemption_disabled+0xce/0xe0
refresh_cpu_vm_stats+0x235/0x5f0
vmstat_update+0x17/0xa0
process_one_work+0x869/0x1aa0
worker_thread+0x5e5/0x1100
kthread+0x29e/0x380
ret_from_fork+0x2d/0x70
ret_from_fork_asm+0x1a/0x30
</TASK>
So, for mm/vmstat:online, disable vmstat_work reliably on teardown and
symmetrically enable it on startup.
For secondary CPUs during CPU hotplug scenarios, ensure the delayed work
is disabled immediately after the initialization. These CPUs are not yet
online when start_shepherd_timer() runs on boot CPU. vmstat_cpu_online()
will enable the work for them.
Link: https://lkml.kernel.org/r/20250108042807.3429745-1-koichiro.den@canonical.com Signed-off-by: Huacai Chen <chenhuacai@kernel.org> Signed-off-by: Koichiro Den <koichiro.den@canonical.com> Suggested-by: Huacai Chen <chenhuacai@kernel.org> Tested-by: Charalampos Mitrodimas <charmitro@posteo.net> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Kairui Song [Tue, 7 Jan 2025 06:54:46 +0000 (14:54 +0800)]
zram: fix potential UAF of zram table
If zram_meta_alloc failed early, it frees allocated zram->table without
setting it NULL. Which will potentially cause zram_meta_free to access
the table if user reset an failed and uninitialized device.
Link: https://lkml.kernel.org/r/20250107065446.86928-1-ryncsn@gmail.com Fixes: 74363ec674cb ("zram: fix uninitialized ZRAM not releasing backing device") Signed-off-by: Kairui Song <kasong@tencent.com> Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Ryan Roberts [Tue, 7 Jan 2025 14:25:53 +0000 (14:25 +0000)]
selftests/mm: set allocated memory to non-zero content in cow test
After commit b1f202060afe ("mm: remap unused subpages to shared zeropage
when splitting isolated thp"), cow test cases involving swapping out THPs
via madvise(MADV_PAGEOUT) started to be skipped due to the subsequent
check via pagemap determining that the memory was not actually swapped
out. Logs similar to this were emitted:
...
# [RUN] Basic COW after fork() ... with swapped-out, PTE-mapped THP (16 kB)
ok 2 # SKIP MADV_PAGEOUT did not work, is swap enabled?
# [RUN] Basic COW after fork() ... with single PTE of swapped-out THP (16 kB)
ok 3 # SKIP MADV_PAGEOUT did not work, is swap enabled?
# [RUN] Basic COW after fork() ... with swapped-out, PTE-mapped THP (32 kB)
ok 4 # SKIP MADV_PAGEOUT did not work, is swap enabled?
...
The commit in question introduces the behaviour of scanning THPs and if
their content is predominantly zero, it splits them and replaces the pages
which are wholly zero with the zero page. These cow test cases were
getting caught up in this.
So let's avoid that by filling the contents of all allocated memory with
a non-zero value. With this in place, the tests are passing again.
Link: https://lkml.kernel.org/r/20250107142555.1870101-1-ryan.roberts@arm.com Fixes: b1f202060afe ("mm: remap unused subpages to shared zeropage when splitting isolated thp") Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Usama Arif <usamaarif642@gmail.com> Cc: Yu Zhao <yuzhao@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Ryan Roberts [Tue, 7 Jan 2025 14:47:52 +0000 (14:47 +0000)]
mm: clear uffd-wp PTE/PMD state on mremap()
When mremap()ing a memory region previously registered with userfaultfd as
write-protected but without UFFD_FEATURE_EVENT_REMAP, an inconsistency in
flag clearing leads to a mismatch between the vma flags (which have
uffd-wp cleared) and the pte/pmd flags (which do not have uffd-wp
cleared). This mismatch causes a subsequent mprotect(PROT_WRITE) to
trigger a warning in page_table_check_pte_flags() due to setting the pte
to writable while uffd-wp is still set.
Fix this by always explicitly clearing the uffd-wp pte/pmd flags on any
such mremap() so that the values are consistent with the existing clearing
of VM_UFFD_WP. Be careful to clear the logical flag regardless of its
physical form; a PTE bit, a swap PTE bit, or a PTE marker. Cover PTE,
huge PMD and hugetlb paths.
Link: https://lkml.kernel.org/r/20250107144755.1871363-2-ryan.roberts@arm.com Co-developed-by: Mikołaj Lenczewski <miko.lenczewski@arm.com> Signed-off-by: Mikołaj Lenczewski <miko.lenczewski@arm.com> Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Closes: https://lore.kernel.org/linux-mm/810b44a8-d2ae-4107-b665-5a42eae2d948@arm.com/ Fixes: 63b2d4174c4a ("userfaultfd: wp: add the writeprotect API to userfaultfd ioctl") Cc: David Hildenbrand <david@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Liam R. Howlett <Liam.Howlett@Oracle.com> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Peter Xu <peterx@redhat.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Petr Pavlu [Tue, 7 Jan 2025 15:34:57 +0000 (16:34 +0100)]
module: fix writing of livepatch relocations in ROX text
A livepatch module can contain a special relocation section
.klp.rela.<objname>.<secname> to apply its relocations at the appropriate
time and to additionally access local and unexported symbols. When
<objname> points to another module, such relocations are processed
separately from the regular module relocation process. For instance, only
when the target <objname> actually becomes loaded.
With CONFIG_STRICT_MODULE_RWX, when the livepatch core decides to apply
these relocations, their processing results in the following bug:
The problem is that the .klp.rela.<objname>.<secname> relocations are
processed after the module was already formed and mod->rw_copy was reset.
However, the code in __write_relocate_add() calls
module_writable_address() which translates the target address 'loc' still
to 'loc + (mem->rw_copy - mem->base)', with mem->rw_copy now being 0.
Fix the problem by returning directly 'loc' in module_writable_address()
when the module is already formed. Function __write_relocate_add() knows
to use text_poke() in such a case.
Link: https://lkml.kernel.org/r/20250107153507.14733-1-petr.pavlu@suse.com Fixes: 0c133b1e78cd ("module: prepare to handle ROX allocations for text") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Reported-by: Marek Maslanka <mmaslanka@google.com> Closes: https://lore.kernel.org/linux-modules/CAGcaFA2hdThQV6mjD_1_U+GNHThv84+MQvMWLgEuX+LVbAyDxg@mail.gmail.com/ Reviewed-by: Petr Mladek <pmladek@suse.com> Tested-by: Petr Mladek <pmladek@suse.com> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Josh Poimboeuf <jpoimboe@kernel.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Mike Rapoport (Microsoft) <rppt@kernel.org> Cc: Petr Mladek <pmladek@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Yosry Ahmed [Wed, 8 Jan 2025 22:24:41 +0000 (22:24 +0000)]
mm: zswap: properly synchronize freeing resources during CPU hotunplug
In zswap_compress() and zswap_decompress(), the per-CPU acomp_ctx of the
current CPU at the beginning of the operation is retrieved and used
throughout. However, since neither preemption nor migration are disabled,
it is possible that the operation continues on a different CPU.
If the original CPU is hotunplugged while the acomp_ctx is still in use,
we run into a UAF bug as some of the resources attached to the acomp_ctx
are freed during hotunplug in zswap_cpu_comp_dead() (i.e.
acomp_ctx.buffer, acomp_ctx.req, or acomp_ctx.acomp).
The problem was introduced in commit 1ec3b5fe6eec ("mm/zswap: move to use
crypto_acomp API for hardware acceleration") when the switch to the
crypto_acomp API was made. Prior to that, the per-CPU crypto_comp was
retrieved using get_cpu_ptr() which disables preemption and makes sure the
CPU cannot go away from under us. Preemption cannot be disabled with the
crypto_acomp API as a sleepable context is needed.
Use the acomp_ctx.mutex to synchronize CPU hotplug callbacks allocating
and freeing resources with compression/decompression paths. Make sure
that acomp_ctx.req is NULL when the resources are freed. In the
compression/decompression paths, check if acomp_ctx.req is NULL after
acquiring the mutex (meaning the CPU was offlined) and retry on the new
CPU.
The initialization of acomp_ctx.mutex is moved from the CPU hotplug
callback to the pool initialization where it belongs (where the mutex is
allocated). In addition to adding clarity, this makes sure that CPU
hotplug cannot reinitialize a mutex that is already locked by
compression/decompression.
Previously a fix was attempted by holding cpus_read_lock() [1]. This
would have caused a potential deadlock as it is possible for code already
holding the lock to fall into reclaim and enter zswap (causing a
deadlock). A fix was also attempted using SRCU for synchronization, but
Johannes pointed out that synchronize_srcu() cannot be used in CPU hotplug
notifiers [2].
Alternative fixes that were considered/attempted and could have worked:
- Refcounting the per-CPU acomp_ctx. This involves complexity in
handling the race between the refcount dropping to zero in
zswap_[de]compress() and the refcount being re-initialized when the
CPU is onlined.
- Disabling migration before getting the per-CPU acomp_ctx [3], but
that's discouraged and is a much bigger hammer than needed, and could
result in subtle performance issues.
Commit eaebeb93922c ("mm: zswap: fix race between [de]compression and CPU
hotunplug") used the CPU hotplug lock in zswap compress/decompress
operations to protect against a race with CPU hotunplug making some
per-CPU resources go away.
However, zswap compress/decompress can be reached through reclaim while
the lock is held, resulting in a potential deadlock as reported by syzbot:
======================================================
WARNING: possible circular locking dependency detected 6.13.0-rc6-syzkaller-00006-g5428dc1906dd #0 Not tainted
------------------------------------------------------
kswapd0/89 is trying to acquire lock: ffffffff8e7d2ed0 (cpu_hotplug_lock){++++}-{0:0}, at: acomp_ctx_get_cpu mm/zswap.c:886 [inline] ffffffff8e7d2ed0 (cpu_hotplug_lock){++++}-{0:0}, at: zswap_compress mm/zswap.c:908 [inline] ffffffff8e7d2ed0 (cpu_hotplug_lock){++++}-{0:0}, at: zswap_store_page mm/zswap.c:1439 [inline] ffffffff8e7d2ed0 (cpu_hotplug_lock){++++}-{0:0}, at: zswap_store+0xa74/0x1ba0 mm/zswap.c:1546
but task is already holding lock: ffffffff8ea355a0 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat mm/vmscan.c:6871 [inline] ffffffff8ea355a0 (fs_reclaim){+.+.}-{0:0}, at: kswapd+0xb58/0x2f30 mm/vmscan.c:7253
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Muchun Song [Mon, 6 Jan 2025 03:31:17 +0000 (11:31 +0800)]
hugetlb: fix NULL pointer dereference in trace_hugetlbfs_alloc_inode
hugetlb_file_setup() will pass a NULL @dir to hugetlbfs_get_inode(), so we
will access a NULL pointer for @dir. Fix it and set __entry->dr to 0 if
@dir is NULL. Because ->i_ino cannot be 0 (see get_next_ino()), there is
no confusing if user sees a 0 inode number.
Link: https://lkml.kernel.org/r/20250106033118.4640-1-songmuchun@bytedance.com Fixes: 318580ad7f28 ("hugetlbfs: support tracepoint") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reported-by: Cheung Wall <zzqq0103.hey@gmail.com> Closes: https://lore.kernel.org/linux-mm/02858D60-43C1-4863-A84F-3C76A8AF1F15@linux.dev/T/# Reviewed-by: Hongbo Li <lihongbo22@huawei.com> Cc: cheung wall <zzqq0103.hey@gmail.com> Cc: Christian Brauner <brauner@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stefan Roesch [Sat, 4 Jan 2025 01:20:37 +0000 (17:20 -0800)]
mm: fix div by zero in bdi_ratio_from_pages
During testing it has been detected, that it is possible to get div by
zero error in bdi_set_min_bytes. The error is caused by the function
bdi_ratio_from_pages(). bdi_ratio_from_pages() calls global_dirty_limits.
If the dirty threshold is 0, the div by zero is raised. This can happen
if the root user is setting:
Juergen Gross [Fri, 3 Jan 2025 06:56:31 +0000 (07:56 +0100)]
x86/execmem: fix ROX cache usage in Xen PV guests
The recently introduced ROX cache for modules is assuming large page
support in 64-bit mode without testing the related feature bit. This
results in breakage when running as a Xen PV guest, as in this mode large
pages are not supported.
Fix that by testing the X86_FEATURE_PSE capability when deciding whether
to enable the ROX cache.
Link: https://lkml.kernel.org/r/20250103065631.26459-1-jgross@suse.com Fixes: 2e45474ab14f ("execmem: add support for cache of large ROX pages") Signed-off-by: Juergen Gross <jgross@suse.com> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mike Rapoport (Microsoft) <rppt@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Marco Nelissen [Thu, 2 Jan 2025 19:04:11 +0000 (11:04 -0800)]
filemap: avoid truncating 64-bit offset to 32 bits
On 32-bit kernels, folio_seek_hole_data() was inadvertently truncating a
64-bit value to 32 bits, leading to a possible infinite loop when writing
to an xfs filesystem.
Link: https://lkml.kernel.org/r/20250102190540.1356838-1-marco.nelissen@gmail.com Fixes: 54fa39ac2e00 ("iomap: use mapping_seek_hole_data") Signed-off-by: Marco Nelissen <marco.nelissen@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Suren Baghdasaryan [Fri, 27 Dec 2024 22:22:20 +0000 (14:22 -0800)]
tools: fix atomic_set() definition to set the value correctly
Currently vma test is failing because of the new vma_assert_attached()
assertion. The check is failing because previous refcount_set() inside
vma_mark_attached() is a NoOp. Fix the definition of atomic_set() to
correctly set the value of the atomic.
Link: https://lkml.kernel.org/r/20241227222220.1726384-1-surenb@google.com Fixes: 9325b8b5a1cb ("tools: add skeleton code for userland testing of VMA logic") Signed-off-by: Suren Baghdasaryan <surenb@google.com> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: Jann Horn <jannh@google.com> Cc: Liam R. Howlett <Liam.Howlett@Oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Honggyu Kim [Fri, 27 Dec 2024 09:57:37 +0000 (18:57 +0900)]
mm/mempolicy: count MPOL_WEIGHTED_INTERLEAVE to "interleave_hit"
Commit fa3bea4e1f82 introduced MPOL_WEIGHTED_INTERLEAVE but it missed
adding its counter to "interleave_hit" of numastat, which is located at
/sys/devices/system/node/nodeN/ directory.
It'd be better to add weighted interleving counter info to the existing
"interleave_hit" instead of introducing a new counter
"weighted_interleave_hit".
Link: https://lkml.kernel.org/r/20241227095737.645-1-honggyu.kim@sk.com Fixes: fa3bea4e1f82 ("mm/mempolicy: introduce MPOL_WEIGHTED_INTERLEAVE for weighted interleaving") Signed-off-by: Honggyu Kim <honggyu.kim@sk.com> Reviewed-by: Gregory Price <gourry@gourry.net> Reviewed-by: Hyeonggon Yoo <hyeonggon.yoo@sk.com> Tested-by: Yunjeong Mun <yunjeong.mun@sk.com> Cc: Andi Kleen <ak@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Luca Ceresoli [Mon, 30 Dec 2024 21:55:10 +0000 (22:55 +0100)]
scripts/decode_stacktrace.sh: fix decoding of lines with an additional info
Since commit bdf8eafbf7f5 ("arm64: stacktrace: report source of unwind
data") a stack trace line can contain an additional info field that was not
present before, in the form of one or more letters in parentheses. E.g.:
[ 504.517915] led_sysfs_enable+0x54/0x80 (P)
^^^
When this is present, decode_stacktrace decodes the line incorrectly:
The regex to match such lines assumes the info can be extended in the
future to other uppercase characters, and will need to be extended in case
other characters will be used. Using a much more generic regex might incur
in false positives, so this looked like a good tradeoff.
Link: https://lkml.kernel.org/r/20241230-decode_stacktrace-fix-info-v1-1-984910659173@bootlin.com Fixes: bdf8eafbf7f5 ("arm64: stacktrace: report source of unwind data") Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Mark Brown <broonie@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Puranjay Mohan <puranjay@kernel.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Linus Torvalds [Sun, 5 Jan 2025 18:52:47 +0000 (10:52 -0800)]
Merge tag 'kbuild-fixes-v6.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix escaping of '$' in scripts/mksysmap
- Fix a modpost crash observed with the latest binutils
- Fix 'provides' in the linux-api-headers pacman package
* tag 'kbuild-fixes-v6.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: pacman-pkg: provide versioned linux-api-headers package
modpost: work around unaligned data access error
modpost: refactor do_vmbus_entry()
modpost: fix the missed iteration for the max bit in do_input()
scripts/mksysmap: Fix escape chars '$'
Linus Torvalds [Sun, 5 Jan 2025 18:37:45 +0000 (10:37 -0800)]
Merge tag 'mm-hotfixes-stable-2025-01-04-18-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"25 hotfixes. 16 are cc:stable. 18 are MM and 7 are non-MM.
The usual bunch of singletons and two doubletons - please see the
relevant changelogs for details"
* tag 'mm-hotfixes-stable-2025-01-04-18-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (25 commits)
MAINTAINERS: change Arınç _NAL's name and email address
scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
mm/util: make memdup_user_nul() similar to memdup_user()
mm, madvise: fix potential workingset node list_lru leaks
mm/damon/core: fix ignored quota goals and filters of newly committed schemes
mm/damon/core: fix new damon_target objects leaks on damon_commit_targets()
mm/list_lru: fix false warning of negative counter
vmstat: disable vmstat_work on vmstat_cpu_down_prep()
mm: shmem: fix the update of 'shmem_falloc->nr_unswapped'
mm: shmem: fix incorrect index alignment for within_size policy
percpu: remove intermediate variable in PERCPU_PTR()
mm: zswap: fix race between [de]compression and CPU hotunplug
ocfs2: fix slab-use-after-free due to dangling pointer dqi_priv
fs/proc/task_mmu: fix pagemap flags with PMD THP entries on 32bit
kcov: mark in_softirq_really() as __always_inline
docs: mm: fix the incorrect 'FileHugeMapped' field
mailmap: modify the entry for Mathieu Othacehe
mm/kmemleak: fix sleeping function called from invalid context at print message
mm: hugetlb: independent PMD page table shared count
maple_tree: reload mas before the second call for mas_empty_area
...
Linus Torvalds [Sun, 5 Jan 2025 18:28:34 +0000 (10:28 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A randconfig build fix and a performance fix:
- Fix the CONFIG_RESET_CONTROLLER=n path signature of
clk_imx8mp_audiomix_reset_controller_register() to appease
randconfig
- Speed up the sdhci clk on TH1520 by a factor of 4 by adding
a fixed factor clk"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: clk-imx8mp-audiomix: fix function signature
clk: thead: Fix TH1520 emmc and shdci clock rate
Thomas Weißschuh [Fri, 3 Jan 2025 18:20:23 +0000 (19:20 +0100)]
kbuild: pacman-pkg: provide versioned linux-api-headers package
The Arch Linux glibc package contains a versioned dependency on
"linux-api-headers". If the linux-api-headers package provided by
pacman-pkg does not specify an explicit version this dependency is not
satisfied.
Fix the dependency by providing an explicit version.
Fixes: c8578539deba ("kbuild: add script and target to generate pacman package") Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Linus Torvalds [Fri, 3 Jan 2025 23:09:12 +0000 (15:09 -0800)]
Merge tag 'sched_ext-for-6.13-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- Fix a bug where bpf_iter_scx_dsq_new() was not initializing the
iterator's flags and could inadvertently enable e.g. reverse
iteration
- Fix a bug where scx_ops_bypass() could call irq_restore twice
- Add Andrea and Changwoo as maintainers for better review coverage
- selftests and tools/sched_ext build and other fixes
* tag 'sched_ext-for-6.13-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Fix dsq_local_on selftest
sched_ext: initialize kit->cursor.flags
sched_ext: Fix invalid irq restore in scx_ops_bypass()
MAINTAINERS: add me as reviewer for sched_ext
MAINTAINERS: add self as reviewer for sched_ext
scx: Fix maximal BPF selftest prog
sched_ext: fix application of sizeof to pointer
selftests/sched_ext: fix build after renames in sched_ext API
sched_ext: Add __weak to fix the build errors
Linus Torvalds [Fri, 3 Jan 2025 23:03:56 +0000 (15:03 -0800)]
Merge tag 'wq-for-6.13-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
- Suppress a corner case spurious flush dependency warning
- Two trivial changes
* tag 'wq-for-6.13-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: add printf attribute to __alloc_workqueue()
workqueue: Do not warn when cancelling WQ_MEM_RECLAIM work from !WQ_MEM_RECLAIM worker
rust: add safety comment in workqueue traits
Linus Torvalds [Fri, 3 Jan 2025 22:58:57 +0000 (14:58 -0800)]
Merge tag 'block-6.13-20250103' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Collection of fixes for block. Particularly the target name overflow
has been a bit annoying, as it results in overwriting random memory
and hence shows up as triggering various other bugs.
- NVMe pull request via Keith:
- Fix device specific quirk for PRP list alignment (Robert)
- Fix target name overflow (Leo)
- Fix target write granularity (Luis)
- Fix target sleeping in atomic context (Nilay)
- Remove unnecessary tcp queue teardown (Chunguang)
- Simple cdrom typo fix"
* tag 'block-6.13-20250103' of git://git.kernel.dk/linux:
cdrom: Fix typo, 'devicen' to 'device'
nvme-tcp: remove nvme_tcp_destroy_io_queues()
nvmet-loop: avoid using mutex in IO hotpath
nvmet: propagate npwg topology
nvmet: Don't overflow subsysnqn
nvme-pci: 512 byte aligned dma pool segment quirk
Linus Torvalds [Fri, 3 Jan 2025 22:45:59 +0000 (14:45 -0800)]
Merge tag 'io_uring-6.13-20250103' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Fix an issue with the read multishot support and posting of CQEs from
io-wq context
- Fix a regression introduced in this cycle, where making the timeout
lock a raw one uncovered another locking dependency. As a result,
move the timeout flushing outside of the timeout lock, punting them
to a local list first
- Fix use of an uninitialized variable in io_async_msghdr. Doesn't
really matter functionally, but silences a valid KMSAN complaint that
it's not always initialized
- Fix use of incrementally provided buffers for read on non-pollable
files, where the buffer always gets committed upfront. Unfortunately
the buffer address isn't resolved first, so the read ends up using
the updated rather than the current value
* tag 'io_uring-6.13-20250103' of git://git.kernel.dk/linux:
io_uring/kbuf: use pre-committed buffer address for non-pollable file
io_uring/net: always initialize kmsg->msg.msg_inq upfront
io_uring/timeout: flush timeouts outside of the timeout lock
io_uring/rw: fix downgraded mshot read
Linus Torvalds [Fri, 3 Jan 2025 22:36:54 +0000 (14:36 -0800)]
Merge tag 'net-6.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireles and netfilter.
Nothing major here. Over the last two weeks we gathered only around
two-thirds of our normal weekly fix count, but delaying sending these
until -rc7 seemed like a really bad idea.
AFAIK we have no bugs under investigation. One or two reverts for
stuff for which we haven't gotten a proper fix will likely come in the
next PR.
Current release - fix to a fix:
- netfilter: nft_set_hash: unaligned atomic read on struct
nft_set_ext
- eth: gve: trigger RX NAPI instead of TX NAPI in gve_xsk_wakeup
Previous releases - regressions:
- net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets
- mptcp:
- fix sleeping rcvmsg sleeping forever after bad recvbuffer adjust
- fix TCP options overflow
- prevent excessive coalescing on receive, fix throughput
- net: fix memory leak in tcp_conn_request() if map insertion fails
- wifi: cw1200: fix potential NULL dereference after conversion to
GPIO descriptors
- phy: micrel: dynamically control external clock of KSZ PHY, fix
suspend behavior
Previous releases - always broken:
- af_packet: fix VLAN handling with MSG_PEEK
- net: restrict SO_REUSEPORT to inet sockets
- netdev-genl: avoid empty messages in NAPI get
- dsa: microchip: fix set_ageing_time function on KSZ9477 and LAN937X
- eth:
- gve: XDP fixes around transmit, queue wakeup etc.
- ti: icssg-prueth: fix firmware load sequence to prevent time
jump which breaks timesync related operations
Misc:
- netlink: specs: mptcp: add missing attr and improve documentation"
* tag 'net-6.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
net: ti: icssg-prueth: Fix clearing of IEP_CMP_CFG registers during iep_init
net: ti: icssg-prueth: Fix firmware load sequence.
mptcp: prevent excessive coalescing on receive
mptcp: don't always assume copied data in mptcp_cleanup_rbuf()
mptcp: fix recvbuffer adjust on sleeping rcvmsg
ila: serialize calls to nf_register_net_hooks()
af_packet: fix vlan_get_protocol_dgram() vs MSG_PEEK
af_packet: fix vlan_get_tci() vs MSG_PEEK
net: wwan: iosm: Properly check for valid exec stage in ipc_mmio_init()
net: restrict SO_REUSEPORT to inet sockets
net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets
net: sfc: Correct key_len for efx_tc_ct_zone_ht_params
net: wwan: t7xx: Fix FSM command timeout issue
sky2: Add device ID 11ab:4373 for Marvell 88E8075
mptcp: fix TCP options overflow.
net: mv643xx_eth: fix an OF node reference leak
gve: trigger RX NAPI instead of TX NAPI in gve_xsk_wakeup
eth: bcmsysport: fix call balance of priv->clk handling routines
net: llc: reset skb->transport_header
netlink: specs: mptcp: fix missing doc
...
Linus Torvalds [Fri, 3 Jan 2025 19:09:35 +0000 (11:09 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A lot of fixes accumulated over the holiday break:
- Static tool fixes, value is already proven to be NULL, possible
integer overflow
- Many bnxt_re fixes:
- Crashes due to a mismatch in the maximum SGE list size
- Don't waste memory for user QPs by creating kernel-only
structures
- Fix compatability issues with older HW in some of the new HW
features recently introduced: RTS->RTS feature, work around 9096
- Do not allow destroy_qp to fail
- Validate QP MTU against device limits
- Add missing validation on madatory QP attributes for RTR->RTS
- Report port_num in query_qp as required by the spec
- Fix creation of QPs of the maximum queue size, and in the
variable mode
- Allow all QPs to be used on newer HW by limiting a work around
only to HW it affects
- Use the correct MSN table size for variable mode QPs
- Add missing locking in create_qp() accessing the qp_tbl
- Form WQE buffers correctly when some of the buffers are 0 hop
- Don't crash on QP destroy if the userspace doesn't setup the
dip_ctx
- Add the missing QP flush handler call on the DWQE path to avoid
hanging on error recovery
- Consistently use ENXIO for return codes if the devices is
fatally errored
- Try again to fix VLAN support on iwarp, previous fix was reverted
due to breaking other cards
- Correct error path return code for rdma netlink events
- Remove the seperate net_device pointer in siw and rxe which
syzkaller found a way to UAF
- Fix a UAF of a stack ib_sge in rtrs
- Fix a regression where old mlx5 devices and FW were wrongly
activing new device features and failing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (28 commits)
RDMA/mlx5: Enable multiplane mode only when it is supported
RDMA/bnxt_re: Fix error recovery sequence
RDMA/rtrs: Ensure 'ib_sge list' is accessible
RDMA/rxe: Remove the direct link to net_device
RDMA/hns: Fix missing flush CQE for DWQE
RDMA/hns: Fix warning storm caused by invalid input in IO path
RDMA/hns: Fix accessing invalid dip_ctx during destroying QP
RDMA/hns: Fix mapping error of zero-hop WQE buffer
RDMA/bnxt_re: Fix the locking while accessing the QP table
RDMA/bnxt_re: Fix MSN table size for variable wqe mode
RDMA/bnxt_re: Add send queue size check for variable wqe
RDMA/bnxt_re: Disable use of reserved wqes
RDMA/bnxt_re: Fix max_qp_wrs reported
RDMA/siw: Remove direct link to net_device
RDMA/nldev: Set error code in rdma_nl_notify_event
RDMA/bnxt_re: Fix reporting hw_ver in query_device
RDMA/bnxt_re: Fix to export port num to ib_query_qp
RDMA/bnxt_re: Fix setting mandatory attributes for modify_qp
RDMA/bnxt_re: Add check for path mtu in modify_qp
RDMA/bnxt_re: Fix the check for 9060 condition
...
Linus Torvalds [Fri, 3 Jan 2025 18:57:57 +0000 (10:57 -0800)]
Merge tag 'pinctrl-v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- A small Kconfig fixup for the i.MX.
In principle this could come in from the SoC tree but the bug was
introduced from the pin control tree so let's fix it from here.
- Fix a sleep in atomic context in the MCP23xxx GPIO expander by
disabling the regmap locking and using explicit mutex locks.
* tag 'pinctrl-v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking
ARM: imx: Re-introduce the PINCTRL selection
Linus Torvalds [Fri, 3 Jan 2025 18:54:51 +0000 (10:54 -0800)]
Merge tag 'sound-6.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The first new year pull request: no surprises, all small fixes,
including:
- Follow-up fixes for the new compress-offload API extension
- A couple of fixes for MIDI 2.0 UMP handling
- A trivial race fix for OSS sequencer emulation ioctls
- USB-audio and HD-audio fixes / quirks"
* tag 'sound-6.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Check UMP support for midi_version change
ALSA hda/realtek: Add quirk for Framework F111:000C
Revert "ALSA: ump: Don't enumeration invalid groups for legacy rawmidi"
ALSA: seq: oss: Fix races at processing SysEx messages
ALSA: compress_offload: fix remaining descriptor races in sound/core/compress_offload.c
ALSA: compress_offload: Drop unneeded no_free_ptr()
ALSA: hda/tas2781: Ignore SUBSYS_ID not found for tas2563 projects
ALSA: usb-audio: US16x08: Initialize array before use
Linus Torvalds [Fri, 3 Jan 2025 18:06:44 +0000 (10:06 -0800)]
Merge tag 'drm-fixes-2025-01-03' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Happy New Year.
It was fairly quiet for holidays period, certainly nothing that worth
getting off the couch before I needed to, this is for the past two
weeks, i915, xe and some adv7511, I expect we will see some amdgpu etc
happening next week, but otherwise all quiet.
xe:
- uapi: Revert some devcoredump file format changes breaking a mesa
debug tool
- Fixes around waits when moving to system
- Fix a typo when checking for LMEM provisioning
- Fix a fault on fd close after unbind
- A couple of OA fixes squashed for stable backporting
adv7511:
- fix UAF
- drop single lane support
- audio infoframe fix"
* tag 'drm-fixes-2025-01-03' of https://gitlab.freedesktop.org/drm/kernel:
xe/oa: Fix query mode of operation for OAR/OAC
drm/i915/dg1: Fix power gate sequence.
drm/i915/cx0_phy: Fix C10 pll programming sequence
drm/xe: Fix fault on fd close after unbind
drm/xe/pf: Use correct function to check LMEM provisioning
drm/xe: Wait for migration job before unmapping pages
drm/xe: Use non-interruptible wait when moving BO to system
drm/xe: Revert some changes that break a mesa debug tool
drm: adv7511: Drop dsi single lane support
dt-bindings: display: adi,adv7533: Drop single lane support
drm: adv7511: Fix use-after-free in adv7533_attach_dsi()
drm/bridge: adv7511_audio: Update Audio InfoFrame properly
Linus Torvalds [Fri, 3 Jan 2025 18:04:43 +0000 (10:04 -0800)]
Merge tag 'ftrace-v6.13-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull ftrace fixes from Steven Rostedt:
- Add needed READ_ONCE() around access to the fgraph array element
The updates to the fgraph array can happen when callbacks are
registered and unregistered. The __ftrace_return_to_handler() can
handle reading either the old value or the new value. But once it
reads that value it must stay consistent otherwise the check that
looks to see if the value is a stub may show false, but if the
compiler decides to re-read after that check, it can be true which
can cause the code to crash later on.
- Make function profiler use the top level ops for filtering again
When function graph became available for instances, its filter ops
became independent from the top level set_ftrace_filter. In the
process the function profiler received its own filter ops as well.
But the function profiler uses the top level set_ftrace_filter file
and does not have one of its own. In giving it its own filter ops, it
lost any user interface it once had. Make it use the top level
set_ftrace_filter file again. This fixes a regression.
* tag 'ftrace-v6.13-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ftrace: Fix function profiler's filtering functionality
fgraph: Add READ_ONCE() when accessing fgraph_array[]
Jens Axboe [Fri, 3 Jan 2025 16:29:09 +0000 (09:29 -0700)]
io_uring/kbuf: use pre-committed buffer address for non-pollable file
For non-pollable files, buffer ring consumption will commit upfront.
This is fine, but io_ring_buffer_select() will return the address of the
buffer after having committed it. For incrementally consumed buffers,
this is incorrect as it will modify the buffer address.
Store the pre-committed value and return that. If that isn't done, then
the initial part of the buffer is not used and the application will
correctly assume the content arrived at the start of the userspace
buffer, but the kernel will have put it later in the buffer. Or it can
cause a spurious -EFAULT returned in the CQE, depending on the buffer
size. As bounds are suitably checked for doing the actual IO, no adverse
side effects are possible - it's just a data misplacement within the
existing buffer.
Reported-by: Gwendal Fernet <gwendalfernet@gmail.com> Cc: stable@vger.kernel.org Fixes: ae98dbf43d75 ("io_uring/kbuf: add support for incremental buffer consumption") Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mark Zhang [Thu, 19 Dec 2024 12:23:36 +0000 (14:23 +0200)]
RDMA/mlx5: Enable multiplane mode only when it is supported
Driver queries vport_cxt.num_plane and enables multiplane when it is
greater then 0, but some old FWs (versions from x.40.1000 till x.42.1000),
report vport_cxt.num_plane = 1 unexpectedly.
Fix it by querying num_plane only when HCA_CAP2.multiplane bit is set.
Fixes: 2a5db20fa532 ("RDMA/mlx5: Add support to multi-plane device and port") Link: https://patch.msgid.link/r/1ef901acdf564716fcf550453cf5e94f343777ec.1734610916.git.leon@kernel.org Cc: stable@vger.kernel.org Reported-by: Francesco Poli <invernomuto@paranoici.org> Closes: https://lore.kernel.org/all/nvs4i2v7o6vn6zhmtq4sgazy2hu5kiulukxcntdelggmznnl7h@so3oul6uwgbl/ Signed-off-by: Mark Zhang <markzhang@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
David S. Miller [Fri, 3 Jan 2025 11:54:06 +0000 (11:54 +0000)]
Merge branch 'net-iep-clock-module-fixes'
Meghana Malladi says:
====================
IEP clock module bug fixes
This series has some bug fixes for IEP module needed by PPS and
timesync operations.
Patch 1/2 fixes firmware load sequence to run all the firmwares
when either of the ethernet interfaces is up. Move all the code
common for firmware bringup under common functions.
Patch 2/2 fixes distorted PPS signal when the ethernet interfaces
are brough down and up. This patch also fixes enabling PPS signal
after bringing the interface up, without disabling PPS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Meghana Malladi [Mon, 23 Dec 2024 15:15:50 +0000 (20:45 +0530)]
net: ti: icssg-prueth: Fix clearing of IEP_CMP_CFG registers during iep_init
When ICSSG interfaces are brought down and brought up again, the
pru cores are shut down and booted again, flushing out all the memories
and start again in a clean state. Hence it is expected that the
IEP_CMP_CFG register needs to be flushed during iep_init() to ensure
that the existing residual configuration doesn't cause any unusual
behavior. If the register is not cleared, existing IEP_CMP_CFG set for
CMP1 will result in SYNC0_OUT signal based on the SYNC_OUT register values.
After bringing the interface up, calling PPS enable doesn't work as
the driver believes PPS is already enabled, (iep->pps_enabled is not
cleared during interface bring down) and driver will just return true
even though there is no signal. Fix this by disabling pps and perout.
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: Meghana Malladi <m-malladi@ti.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Timesync related operations are ran in PRU0 cores for both ICSSG SLICE0
and SLICE1. Currently whenever any ICSSG interface comes up we load the
respective firmwares to PRU cores and whenever interface goes down, we
stop the resective cores. Due to this, when SLICE0 goes down while
SLICE1 is still active, PRU0 firmwares are unloaded and PRU0 core is
stopped. This results in clock jump for SLICE1 interface as the timesync
related operations are no longer running.
As there are interdependencies between SLICE0 and SLICE1 firmwares,
fix this by running both PRU0 and PRU1 firmwares as long as at least 1
ICSSG interface is up. Add new flag in prueth struct to check if all
firmwares are running and remove the old flag (fw_running).
Use emacs_initialized as reference count to load the firmwares for the
first and last interface up/down. Moving init_emac_mode and fw_offload_mode
API outside of icssg_config to icssg_common_start API as they need
to be called only once per firmware boot.
Change prueth_emac_restart() to return error code and add error prints
inside the caller of this functions in case of any failures.
Move prueth_emac_stop() from common to sr1 driver.
sr1 and sr2 drivers have different logic handling for stopping
the firmwares. While sr1 driver is dependent on emac structure
to stop the corresponding pru cores for that slice, for sr2
all the pru cores of both the slices are stopped and is not
dependent on emac. So the prueth_emac_stop() function is no
longer common and can be moved to sr1 driver.
Fixes: c1e0230eeaab ("net: ti: icss-iep: Add IEP driver") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Meghana Malladi <m-malladi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 3 Jan 2025 02:44:05 +0000 (18:44 -0800)]
Merge branch 'mptcp-rx-path-fixes'
Matthieu Baerts says:
====================
mptcp: rx path fixes
Here are 3 different fixes, all related to the MPTCP receive buffer:
- Patch 1: fix receive buffer space when recvmsg() blocks after
receiving some data. For a fix introduced in v6.12, backported to
v6.1.
- Patch 2: mptcp_cleanup_rbuf() can be called when no data has been
copied. For 5.11.
- Patch 3: prevent excessive coalescing on receive, which can affect the
throughput badly. It looks better to wait a bit before backporting
this one to stable versions, to get more results. For 5.10.
====================
Paolo Abeni [Mon, 30 Dec 2024 18:12:32 +0000 (19:12 +0100)]
mptcp: prevent excessive coalescing on receive
Currently the skb size after coalescing is only limited by the skb
layout (the skb must not carry frag_list). A single coalesced skb
covering several MSS can potentially fill completely the receive
buffer. In such a case, the snd win will zero until the receive buffer
will be empty again, affecting tput badly.
Fixes: 8268ed4c9d19 ("mptcp: introduce and use mptcp_try_coalesce()") Cc: stable@vger.kernel.org # please delay 2 weeks after 6.13-final release Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-3-8608af434ceb@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Mon, 30 Dec 2024 18:12:31 +0000 (19:12 +0100)]
mptcp: don't always assume copied data in mptcp_cleanup_rbuf()
Under some corner cases the MPTCP protocol can end-up invoking
mptcp_cleanup_rbuf() when no data has been copied, but such helper
assumes the opposite condition.
Explicitly drop such assumption and performs the costly call only
when strictly needed - before releasing the msk socket lock.
Fixes: fd8976790a6c ("mptcp: be careful on MPTCP-level ack.") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-2-8608af434ceb@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Mon, 30 Dec 2024 18:12:30 +0000 (19:12 +0100)]
mptcp: fix recvbuffer adjust on sleeping rcvmsg
If the recvmsg() blocks after receiving some data - i.e. due to
SO_RCVLOWAT - the MPTCP code will attempt multiple times to
adjust the receive buffer size, wrongly accounting every time the
cumulative of received data - instead of accounting only for the
delta.
Address the issue moving mptcp_rcv_space_adjust just after the
data reception and passing it only the just received bytes.
This also removes an unneeded difference between the TCP and MPTCP
RX code path implementation.
Fixes: 581302298524 ("mptcp: error out earlier on disconnect") Cc: stable@vger.kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20241230-net-mptcp-rbuf-fixes-v1-1-8608af434ceb@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 30 Dec 2024 16:28:49 +0000 (16:28 +0000)]
ila: serialize calls to nf_register_net_hooks()
syzbot found a race in ila_add_mapping() [1]
commit 031ae72825ce ("ila: call nf_unregister_net_hooks() sooner")
attempted to fix a similar issue.
Looking at the syzbot repro, we have concurrent ILA_CMD_ADD commands.
Add a mutex to make sure at most one thread is calling nf_register_net_hooks().
[1]
BUG: KASAN: slab-use-after-free in rht_key_hashfn include/linux/rhashtable.h:159 [inline]
BUG: KASAN: slab-use-after-free in __rhashtable_lookup.constprop.0+0x426/0x550 include/linux/rhashtable.h:604
Read of size 4 at addr ffff888028f40008 by task dhcpcd/5501
Maciej S. Szmigiero [Sun, 29 Dec 2024 16:46:58 +0000 (17:46 +0100)]
net: wwan: iosm: Properly check for valid exec stage in ipc_mmio_init()
ipc_mmio_init() used the post-decrement operator in its loop continuing
condition of "retries" counter being "> 0", which meant that when this
condition caused loop exit "retries" counter reached -1.
But the later valid exec stage failure check only tests for "retries"
counter being exactly zero, so it didn't trigger in this case (but
would wrongly trigger if the code reaches a valid exec stage in the
very last loop iteration).
Fix this by using the pre-decrement operator instead, so the loop counter
is exactly zero on valid exec stage failure.
Fixes: 8c7138b33e5c ("net: Unpublish sk from sk_reuseport_cb before call_rcu") Reported-by: syzbot+b3e02953598f447d4d2a@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/6772f2f4.050a0220.2f3838.04cb.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20241231160527.3994168-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Willem de Bruijn [Wed, 1 Jan 2025 16:47:40 +0000 (11:47 -0500)]
net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets
The blamed commit disabled hardware offoad of IPv6 packets with
extension headers on devices that advertise NETIF_F_IPV6_CSUM,
based on the definition of that feature in skbuff.h:
* * - %NETIF_F_IPV6_CSUM
* - Driver (device) is only able to checksum plain
* TCP or UDP packets over IPv6. These are specifically
* unencapsulated packets of the form IPv6|TCP or
* IPv6|UDP where the Next Header field in the IPv6
* header is either TCP or UDP. IPv6 extension headers
* are not supported with this feature. This feature
* cannot be set in features for a device with
* NETIF_F_HW_CSUM also set. This feature is being
* DEPRECATED (see below).
The change causes skb_warn_bad_offload to fire for BIG TCP
packets.
[ 496.310233] WARNING: CPU: 13 PID: 23472 at net/core/dev.c:3129 skb_warn_bad_offload+0xc4/0xe0
BIG TCP introduced an IPV6_TLV_JUMBO IPv6 extension header to
communicate packet length, as this is an IPv6 jumbogram. But, the
feature is only enabled on devices that support BIG TCP TSO. The
header is only present for PF_PACKET taps like tcpdump, and not
transmitted by physical devices.
For this specific case of extension headers that are not
transmitted, return to the situation before the blamed commit
and support hardware offload.
ipv6_has_hopopt_jumbo() tests not only whether this header is present,
but also that it is the only extension header before a terminal (L4)
header.
Fixes: 04c20a9356f2 ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Eric Dumazet <edumazet@google.com> Closes: https://lore.kernel.org/netdev/CANn89iK1hdC3Nt8KPhOtTF8vCPc1AHDCtse_BTNki1pWxAByTQ@mail.gmail.com/ Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250101164909.1331680-1-willemdebruijn.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Liang Jie [Mon, 30 Dec 2024 09:37:09 +0000 (17:37 +0800)]
net: sfc: Correct key_len for efx_tc_ct_zone_ht_params
In efx_tc_ct_zone_ht_params, the key_len was previously set to
offsetof(struct efx_tc_ct_zone, linkage). This calculation is incorrect
because it includes any padding between the zone field and the linkage
field due to structure alignment, which can vary between systems.
This patch updates key_len to use sizeof_field(struct efx_tc_ct_zone, zone)
, ensuring that the hash table correctly uses the zone as the key. This fix
prevents potential hash lookup errors and improves connection tracking
reliability.
Fixes: c3bb5c6acd4e ("sfc: functions to register for conntrack zone offload") Signed-off-by: Liang Jie <liangjie@lixiang.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://patch.msgid.link/20241230093709.3226854-1-buaajxlj@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dave Airlie [Fri, 3 Jan 2025 00:28:43 +0000 (10:28 +1000)]
Merge tag 'drm-xe-fixes-2024-12-23' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
UAPI Changes:
- Revert some devcoredump file format changes
breaking a mesa debug tool (John)
Driver Changes:
- Fixes around waits when moving to system (Nirmoy)
- Fix a typo when checking for LMEM provisioning (Michal)
- Fix a fault on fd close after unbind (Lucas)
and it is correct, as it's never initialized upfront. Hence the first
submission can end up using it uninitialized, if the recv wasn't
successful and the networking stack didn't honor ->msg_get_inq being set
and filling in the output value of ->msg_inq as requested.
Set it to 0 upfront when it's allocated, just to silence this KMSAN
warning. There's no side effect of using it uninitialized, it'll just
potentially cause the next receive to use a recv value hint that's not
accurate.
Fixes: c6f32c7d9e09 ("io_uring/net: get rid of ->prep_async() for receive side") Reported-by: syzbot+068ff190354d2f74892f@syzkaller.appspotmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kohei Enju [Wed, 1 Jan 2025 19:08:20 +0000 (04:08 +0900)]
ftrace: Fix function profiler's filtering functionality
Commit c132be2c4fcc ("function_graph: Have the instances use their own
ftrace_ops for filtering"), function profiler (enabled via
function_profile_enabled) has been showing statistics for all functions,
ignoring set_ftrace_filter settings.
While tracers are instantiated, the function profiler is not. Therefore, it
should use the global set_ftrace_filter for consistency. This patch
modifies the function profiler to use the global filter, fixing the
filtering functionality.
Before (filtering not working):
```
root@localhost:~# echo 'vfs*' > /sys/kernel/tracing/set_ftrace_filter
root@localhost:~# echo 1 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# sleep 1
root@localhost:~# echo 0 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# head /sys/kernel/tracing/trace_stat/*
Function Hit Time Avg
s^2
-------- --- ---- ---
---
schedule 314 22290594 us 70989.15 us 40372231 us
x64_sys_call 1527 8762510 us 5738.382 us 3414354 us
schedule_hrtimeout_range 176 8665356 us 49234.98 us 405618876 us
__x64_sys_ppoll 324 5656635 us 17458.75 us 19203976 us
do_sys_poll 324 5653747 us 17449.83 us 19214945 us
schedule_timeout 67 5531396 us 82558.15 us 2136740827 us
__x64_sys_pselect6 12 3029540 us 252461.7 us 63296940171 us
do_pselect.constprop.0 12 3029532 us 252461.0 us 63296952931 us
```
After (filtering working):
```
root@localhost:~# echo 'vfs*' > /sys/kernel/tracing/set_ftrace_filter
root@localhost:~# echo 1 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# sleep 1
root@localhost:~# echo 0 > /sys/kernel/tracing/function_profile_enabled
root@localhost:~# head /sys/kernel/tracing/trace_stat/*
Function Hit Time Avg
s^2
-------- --- ---- ---
---
vfs_write 462 68476.43 us 148.217 us
25874.48 us
vfs_read 641 9611.356 us 14.994 us
28868.07 us
vfs_fstat 890 878.094 us 0.986 us
1.667 us
vfs_fstatat 227 757.176 us 3.335 us
18.928 us
vfs_statx 226 610.610 us 2.701 us
17.749 us
vfs_getattr_nosec 1187 460.919 us 0.388 us
0.326 us
vfs_statx_path 297 343.287 us 1.155 us
11.116 us
vfs_rename 6 291.575 us 48.595 us
9889.236 us
```
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/20250101190820.72534-1-enjuk@amazon.com Fixes: c132be2c4fcc ("function_graph: Have the instances use their own ftrace_ops for filtering") Signed-off-by: Kohei Enju <enjuk@amazon.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Zilin Guan [Tue, 31 Dec 2024 11:37:31 +0000 (11:37 +0000)]
fgraph: Add READ_ONCE() when accessing fgraph_array[]
In __ftrace_return_to_handler(), a loop iterates over the fgraph_array[]
elements, which are fgraph_ops. The loop checks if an element is a
fgraph_stub to prevent using a fgraph_stub afterward.
However, if the compiler reloads fgraph_array[] after this check, it might
race with an update to fgraph_array[] that introduces a fgraph_stub. This
could result in the stub being processed, but the stub contains a null
"func_hash" field, leading to a NULL pointer dereference.
To ensure that the gops compared against the fgraph_stub matches the gops
processed later, add a READ_ONCE(). A similar patch appears in commit 63a8dfb ("function_graph: Add READ_ONCE() when accessing fgraph_array[]").
Cc: stable@vger.kernel.org Fixes: 37238abe3cb47 ("ftrace/function_graph: Pass fgraph_ops to function graph callbacks") Link: https://lore.kernel.org/20241231113731.277668-1-zilin@seu.edu.cn Signed-off-by: Zilin Guan <zilin@seu.edu.cn> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Olof Johansson [Thu, 2 Jan 2025 14:30:03 +0000 (06:30 -0800)]
MAINTAINERS: Remove Olof from SoC maintainers
I haven't been an active participant for a couple of years now, and
after discussions at Linux Plumbers in 2024, Arnd is getting fresh help
from a few more participants.
It's time to remove myself, and spare myself from patches and pull
requests in my inbox.
Linus Torvalds [Thu, 2 Jan 2025 18:40:40 +0000 (10:40 -0800)]
Merge tag 'pmdomain-v6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
- Silence warning by adding a dummy release function
- imx: Fix an OF node reference leak in imx_gpcv2_probe()
* tag 'pmdomain-v6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: core: add dummy release function to genpd device
pmdomain: imx: gpcv2: fix an OF node reference leak in imx_gpcv2_probe()
This is a set of squashed commits to facilitate smooth applying to
stable. Each commit message is retained for reference.
1) Allow a GGTT mapped batch to be submitted to user exec queue
For a OA use case, one of the HW registers needs to be modified by
submitting an MI_LOAD_REGISTER_IMM command to the users exec queue, so
that the register is modified in the user's hardware context. In order
to do this a batch that is mapped in GGTT, needs to be submitted to the
user exec queue. Since all user submissions use q->vm and hence PPGTT,
add some plumbing to enable submission of batches mapped in GGTT.
v2: ggtt is zero-initialized, so no need to set it false (Matt Brost)
2) xe/oa: Use MI_LOAD_REGISTER_IMMEDIATE to enable OAR/OAC
To enable OAR/OAC, a bit in RING_CONTEXT_CONTROL needs to be set.
Setting this bit cause the context image size to change and if not done
correct, can cause undesired hangs.
Current code uses a separate exec_queue to modify this bit and is
error-prone. As per HW recommendation, submit MI_LOAD_REGISTER_IMM to
the target hardware context to modify the relevant bit.
In v2 version, an attempt to submit everything to the user-queue was
made, but it failed the unprivileged-single-ctx-counters test. It
appears that the OACTXCONTROL must be modified from a remote context.
In v3 version, all context specific register configurations were moved
to use LOAD_REGISTER_IMMEDIATE and that seems to work well. This is a
cleaner way, since we can now submit all configuration to user
exec_queue and the fence handling is simplified.
v2:
(Matt)
- set job->ggtt to true if create job is successful
- unlock vm on job error
(Ashutosh)
- don't wait on job submission
- use kernel exec queue where possible
v3:
(Ashutosh)
- Fix checkpatch issues
- Remove extra spaces/new-lines
- Add Fixes: and Cc: tags
- Reset context control bit when OA stream is closed
- Submit all config via MI_LOAD_REGISTER_IMMEDIATE
(Umesh)
- Update commit message for v3 experiment
- Squash patches for easier port to stable
v4:
(Ashutosh)
- No need to pass q to xe_oa_submit_bb
- Do not support exec queues with width > 1
- Fix disabling of CTX_CTRL_OAC_CONTEXT_ENABLE
v5:
(Ashutosh)
- Drop reg_lri related comments
- Use XE_OA_SUBMIT_NO_DEPS in xe_oa_load_with_lri
Fixes: 8135f1c09dd2 ("drm/xe/oa: Don't reset OAC_CONTEXT_ENABLE on OA stream close") Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Matthew Brost <matthew.brost@intel.com> # commit 1 Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Cc: stable@vger.kernel.org Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com> Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20241220171919.571528-2-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 55039832f98c7e05f1cf9e0d8c12b2490abd0f16) Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Linus Torvalds [Wed, 1 Jan 2025 19:22:07 +0000 (11:22 -0800)]
Merge tag 'trace-v6.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix trace event string check when dealing with array of strings
The xe_bo_move event has a field that indexes into an array of
strings. The TP_fast_assign() added the index into the ring buffer and
the TP_printk() had a "%s" that referenced the array using the index
in the ring buffer. This is a legitimate use of "%s" in trace events.
But this triggered a false positive in the test_event_printk() at boot
saying that the string was dangerous.
Change the check to allow arrays using fields in the ring buffer as an
index to be considered a safe string"
* tag 'trace-v6.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Have process_string() also allow arrays
Takashi Iwai [Tue, 31 Dec 2024 14:53:58 +0000 (15:53 +0100)]
ALSA: seq: Check UMP support for midi_version change
When the kernel is built without UMP support but a user-space app
requires the midi_version > 0, the kernel should return an error.
Otherwise user-space assumes as if it were possible to deal,
eventually hitting serious errors later.
Kalesh AP [Tue, 31 Dec 2024 02:50:08 +0000 (08:20 +0530)]
RDMA/bnxt_re: Fix error recovery sequence
Fixed to return ENXIO from __send_message_basic_sanity()
to indicate that device is in error state. In the case of
ERR_DEVICE_DETACHED state, the driver should not post the
commands to the firmware as it will time out eventually.
Removed bnxt_re_modify_qp() call from bnxt_re_dev_stop()
as it is a no-op.
Fixes: cc5b9b48d447 ("RDMA/bnxt_re: Recover the device when FW error is detected") Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Link: https://patch.msgid.link/20241231025008.2267162-1-kalesh-anakkur.purayil@broadcom.com Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by: Leon Romanovsky <leon@kernel.org>
Li Zhijian [Tue, 31 Dec 2024 01:34:16 +0000 (09:34 +0800)]
RDMA/rtrs: Ensure 'ib_sge list' is accessible
Move the declaration of the 'ib_sge list' variable outside the
'always_invalidate' block to ensure it remains accessible for use
throughout the function.
Previously, 'ib_sge list' was declared within the 'always_invalidate'
block, limiting its accessibility, then caused a
'BUG: kernel NULL pointer dereference'[1].
? __die_body.cold+0x19/0x27
? page_fault_oops+0x15a/0x2d0
? search_module_extables+0x19/0x60
? search_bpf_extables+0x5f/0x80
? exc_page_fault+0x7e/0x180
? asm_exc_page_fault+0x26/0x30
? memcpy_orig+0xd5/0x140
rxe_mr_copy+0x1c3/0x200 [rdma_rxe]
? rxe_pool_get_index+0x4b/0x80 [rdma_rxe]
copy_data+0xa5/0x230 [rdma_rxe]
rxe_requester+0xd9b/0xf70 [rdma_rxe]
? finish_task_switch.isra.0+0x99/0x2e0
rxe_sender+0x13/0x40 [rdma_rxe]
do_task+0x68/0x1e0 [rdma_rxe]
process_one_work+0x177/0x330
worker_thread+0x252/0x390
? __pfx_worker_thread+0x10/0x10
This change ensures the variable is available for subsequent operations
that require it.
Daniel Schaefer [Tue, 31 Dec 2024 04:59:58 +0000 (12:59 +0800)]
ALSA hda/realtek: Add quirk for Framework F111:000C
Similar to commit eb91c456f371
("ALSA: hda/realtek: Add Framework Laptop 13 (Intel Core Ultra) to quirks")
and previous quirks for Framework systems with
Realtek codecs.
000C is a new platform that will also have an ALC285 codec and needs the
same quirk.
Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: linux@frame.work Cc: Dustin L. Howett <dustin@howett.net> Signed-off-by: Daniel Schaefer <dhs@frame.work> Cc: <stable@vger.kernel.org> Link: https://patch.msgid.link/20241231045958.14545-1-dhs@frame.work Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steven Rostedt [Tue, 31 Dec 2024 05:06:46 +0000 (00:06 -0500)]
tracing: Have process_string() also allow arrays
In order to catch a common bug where a TRACE_EVENT() TP_fast_assign()
assigns an address of an allocated string to the ring buffer and then
references it in TP_printk(), which can be executed hours later when the
string is free, the function test_event_printk() runs on all events as
they are registered to make sure there's no unwanted dereferencing.
It calls process_string() to handle cases in TP_printk() format that has
"%s". It returns whether or not the string is safe. But it can have some
false positives.
Where the "%s" references into xe_mem_type_to_name[]. This is an array of
pointers that should be safe for the event to access. Instead of flagging
this as a bad reference, if a reference points to an array, where the
record field is the index, consider it safe.
Jinjian Song [Tue, 24 Dec 2024 04:15:52 +0000 (12:15 +0800)]
net: wwan: t7xx: Fix FSM command timeout issue
When driver processes the internal state change command, it use an
asynchronous thread to process the command operation. If the main
thread detects that the task has timed out, the asynchronous thread
will panic when executing the completion notification because the
main thread completion object has been released.
Kuan-Wei Chiu [Thu, 26 Dec 2024 14:03:32 +0000 (22:03 +0800)]
scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
The orc_sort_cmp() function, used with qsort(), previously violated the
symmetry and transitivity rules required by the C standard. Specifically,
when both entries are ORC_TYPE_UNDEFINED, it could result in both a < b
and b < a, which breaks the required symmetry and transitivity. This can
lead to undefined behavior and incorrect sorting results, potentially
causing memory corruption in glibc implementations [1].
Symmetry: If x < y, then y > x.
Transitivity: If x < y and y < z, then x < z.
Fix the comparison logic to return 0 when both entries are
ORC_TYPE_UNDEFINED, ensuring compliance with qsort() requirements.
Tetsuo Handa [Sat, 21 Dec 2024 07:47:29 +0000 (16:47 +0900)]
mm/util: make memdup_user_nul() similar to memdup_user()
Since the string data to copy from userspace is likely less than PAGE_SIZE
bytes, replace GFP_KERNEL with GFP_USER like commit 6c2c97a24f09
("memdup_user(): switch to GFP_USER") does and add __GFP_NOWARN like
commit 6c8fcc096be9 ("mm: don't let userspace spam allocations warnings")
does. Also, use dedicated slab buckets like commit d73778e4b867
("mm/util: Use dedicated slab buckets for memdup_user()") does.
Kairui Song [Sun, 22 Dec 2024 12:29:36 +0000 (20:29 +0800)]
mm, madvise: fix potential workingset node list_lru leaks
Since commit 5abc1e37afa0 ("mm: list_lru: allocate list_lru_one only when
needed"), all list_lru users need to allocate the items using the new
infrastructure that provides list_lru info for slab allocation, ensuring
that the corresponding memcg list_lru is allocated before use.
For workingset shadow nodes (which are xa_node), users are converted to
use the new infrastructure by commit 9bbdc0f32409 ("xarray: use
kmem_cache_alloc_lru to allocate xa_node"). The xas->xa_lru will be set
correctly for filemap users. However, there is a missing case: xa_node
allocations caused by madvise(..., MADV_COLLAPSE).
madvise(..., MADV_COLLAPSE) will also read in the absent parts of file
map, and there will be xa_nodes allocated for the caller's memcg (assuming
it's not rootcg). However, these allocations won't trigger memcg list_lru
allocation because the proper xas info was not set.
If nothing else has allocated other xa_nodes for that memcg to trigger
list_lru creation, and memory pressure starts to evict file pages,
workingset_update_node will try to add these xa_nodes to their
corresponding memcg list_lru, and it does not exist (NULL). So they will
be added to rootcg's list_lru instead.
This shouldn't be a significant issue in practice, but it is indeed
unexpected behavior, and these xa_nodes will not be reclaimed effectively.
And may lead to incorrect counting of the list_lru->nr_items counter.
This problem wasn't exposed until recent commit 28e98022b31ef
("mm/list_lru: simplify reparenting and initial allocation") added a
sanity check: only dying memcg could have a NULL list_lru when
list_lru_{add,del} is called. This problem triggered this WARNING.
So make madvise(..., MADV_COLLAPSE) also call xas_set_lru() to pass the
list_lru which we may want to insert xa_node into later. And move
mapping_set_update to mm/internal.h, and turn into a macro to avoid
including extra headers in mm/internal.h.
Link: https://lkml.kernel.org/r/20241222122936.67501-1-ryncsn@gmail.com Fixes: 9bbdc0f32409 ("xarray: use kmem_cache_alloc_lru to allocate xa_node") Reported-by: syzbot+38a0cbd267eff2d286ff@syzkaller.appspotmail.com Closes: https://lore.kernel.org/lkml/675d01e9.050a0220.37aaf.00be.GAE@google.com/ Signed-off-by: Kairui Song <kasong@tencent.com> Cc: Chengming Zhou <chengming.zhou@linux.dev> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Sasha Levin <sashal@kernel.org> Cc: Shakeel Butt <shakeel.butt@linux.dev> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
SeongJae Park [Sun, 22 Dec 2024 23:12:22 +0000 (15:12 -0800)]
mm/damon/core: fix ignored quota goals and filters of newly committed schemes
damon_commit_schemes() ignores quota goals and filters of the newly
committed schemes. This makes users confused about the behaviors.
Correctly handle those inputs.
Link: https://lkml.kernel.org/r/20241222231222.85060-3-sj@kernel.org Fixes: 9cb3d0b9dfce ("mm/damon/core: implement DAMON context commit function") Signed-off-by: SeongJae Park <sj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
SeongJae Park [Sun, 22 Dec 2024 23:12:21 +0000 (15:12 -0800)]
mm/damon/core: fix new damon_target objects leaks on damon_commit_targets()
Patch series "mm/damon/core: fix memory leaks and ignored inputs from
damon_commit_ctx()".
Due to two bugs in damon_commit_targets() and damon_commit_schemes(),
which are called from damon_commit_ctx(), some user inputs can be ignored,
and some mmeory objects can be leaked. Fix those.
Note that only DAMON sysfs interface users are affected. Other DAMON core
API user modules that more focused more on simple and dedicated production
usages, including DAMON_RECLAIM and DAMON_LRU_SORT are not using the buggy
function in the way, so not affected.
This patch (of 2):
When new DAMON targets are added via damon_commit_targets(), the newly
created targets are not deallocated when updating the internal data
(damon_commit_target()) is failed. Worse yet, even if the setup is
successfully done, the new target is not linked to the context. Hence,
the new targets are always leaked regardless of the internal data setup
failure. Fix the leaks.
Link: https://lkml.kernel.org/r/20241222231222.85060-2-sj@kernel.org Fixes: 9cb3d0b9dfce ("mm/damon/core: implement DAMON context commit function") Signed-off-by: SeongJae Park <sj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Kairui Song [Mon, 23 Dec 2024 15:09:07 +0000 (23:09 +0800)]
mm/list_lru: fix false warning of negative counter
commit 2788cf0c401c ("memcg: reparent list_lrus and free kmemcg_id on css
offline") removed sanity checks for the nr_items counter's value because
it implemented list_lru re-parenting in a way that will redirect
children's list_lru to the parent before re-parenting the items in
list_lru. This will make item counter uncharging happen in the parent
while the item is still being held by the child. As a result, the
parent's counter value may become negative. This is acceptable because
re-parenting will sum up the children's counter values, and the parent's
counter will be fixed.
Later commit fb56fdf8b9a2 ("mm/list_lru: split the lock to per-cgroup
scope") reworked the re-parenting process, and removed the redirect. So
it added the sanity check back, assuming that as long as items are still
in the children's list_lru, parent's counter will not be uncharged.
But that assumption is incorrect. The xas_store in
memcg_reparent_list_lrus will set children's list_lru to NULL before
re-parenting the items, it redirects list_lru helpers to use parent's
list_lru just like before. But still, it's not a problem as re-parenting
will fix the counter.
Therefore, remove this sanity check, but add a new check to ensure that
the counter won't go negative in a different way: the child's list_lru
being re-parented should never have a negative counter, since re-parenting
should occur in order and fixes counters.
Link: https://lkml.kernel.org/r/20241223150907.1591-1-ryncsn@gmail.com Fixes: fb56fdf8b9a2 ("mm/list_lru: split the lock to per-cgroup scope") Signed-off-by: Kairui Song <kasong@tencent.com> Closes: https://lore.kernel.org/lkml/Z2Bz9t92Be9l1xqj@lappy/ Cc: Chengming Zhou <zhouchengming@bytedance.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Qi Zheng <zhengqi.arch@bytedance.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Sasha Levin <sashal@kernel.org> Cc: Shakeel Butt <shakeel.butt@linux.dev> Cc: Yu Zhao <yuzhao@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Koichiro Den [Sat, 21 Dec 2024 03:33:20 +0000 (12:33 +0900)]
vmstat: disable vmstat_work on vmstat_cpu_down_prep()
Even after mm/vmstat:online teardown, shepherd may still queue work for
the dying cpu until the cpu is removed from online mask. While it's quite
rare, this means that after unbind_workers() unbinds a per-cpu kworker, it
potentially runs vmstat_update for the dying CPU on an irrelevant cpu
before entering atomic AP states. When CONFIG_DEBUG_PREEMPT=y, it results
in the following error with the backtrace.
BUG: using smp_processor_id() in preemptible [00000000] code: \
kworker/7:3/1702
caller is refresh_cpu_vm_stats+0x235/0x5f0
CPU: 0 UID: 0 PID: 1702 Comm: kworker/7:3 Tainted: G
Tainted: [N]=TEST
Workqueue: mm_percpu_wq vmstat_update
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xb0
check_preemption_disabled+0xce/0xe0
refresh_cpu_vm_stats+0x235/0x5f0
vmstat_update+0x17/0xa0
process_one_work+0x869/0x1aa0
worker_thread+0x5e5/0x1100
kthread+0x29e/0x380
ret_from_fork+0x2d/0x70
ret_from_fork_asm+0x1a/0x30
</TASK>
So, for mm/vmstat:online, disable vmstat_work reliably on teardown and
symmetrically enable it on startup.
Baolin Wang [Thu, 19 Dec 2024 07:30:09 +0000 (15:30 +0800)]
mm: shmem: fix the update of 'shmem_falloc->nr_unswapped'
The 'shmem_falloc->nr_unswapped' is used to record how many writepage
refused to swap out because fallocate() is allocating, but after shmem
supports large folio swap out, the update of 'shmem_falloc->nr_unswapped'
does not use the correct number of pages in the large folio, which may
lead to fallocate() not exiting as soon as possible.
Anyway, this is found through code inspection, and I am not sure whether
it would actually cause serious issues.
Baolin Wang [Thu, 19 Dec 2024 07:30:08 +0000 (15:30 +0800)]
mm: shmem: fix incorrect index alignment for within_size policy
With enabling the shmem per-size within_size policy, using an incorrect
'order' size to round_up() the index can lead to incorrect i_size checks,
resulting in an inappropriate large orders being returned.
Changing to use '1 << order' to round_up() the index to fix this issue.
Additionally, adding an 'aligned_index' variable to avoid affecting the
index checks.
Gal Pressman [Thu, 19 Dec 2024 12:18:28 +0000 (14:18 +0200)]
percpu: remove intermediate variable in PERCPU_PTR()
The intermediate variable in the PERCPU_PTR() macro results in a kernel
panic on boot [1] due to a compiler bug seen when compiling the kernel
(+ KASAN) with gcc 11.3.1, but not when compiling with latest gcc
(v14.2)/clang(v18.1).
To solve it, remove the intermediate variable (which is not needed) and
keep the casting that resolves the address space checks.
Yosry Ahmed [Thu, 19 Dec 2024 21:24:37 +0000 (21:24 +0000)]
mm: zswap: fix race between [de]compression and CPU hotunplug
In zswap_compress() and zswap_decompress(), the per-CPU acomp_ctx of the
current CPU at the beginning of the operation is retrieved and used
throughout. However, since neither preemption nor migration are disabled,
it is possible that the operation continues on a different CPU.
If the original CPU is hotunplugged while the acomp_ctx is still in use,
we run into a UAF bug as the resources attached to the acomp_ctx are freed
during hotunplug in zswap_cpu_comp_dead().
The problem was introduced in commit 1ec3b5fe6eec ("mm/zswap: move to use
crypto_acomp API for hardware acceleration") when the switch to the
crypto_acomp API was made. Prior to that, the per-CPU crypto_comp was
retrieved using get_cpu_ptr() which disables preemption and makes sure the
CPU cannot go away from under us. Preemption cannot be disabled with the
crypto_acomp API as a sleepable context is needed.
Commit 8ba2f844f050 ("mm/zswap: change per-cpu mutex and buffer to
per-acomp_ctx") increased the UAF surface area by making the per-CPU
buffers dynamic, adding yet another resource that can be freed from under
zswap compression/decompression by CPU hotunplug.
There are a few ways to fix this:
(a) Add a refcount for acomp_ctx.
(b) Disable migration while using the per-CPU acomp_ctx.
(c) Disable CPU hotunplug while using the per-CPU acomp_ctx by holding
the CPUs read lock.
Implement (c) since it's simpler than (a), and (b) involves using
migrate_disable() which is apparently undesired (see huge comment in
include/linux/preempt.h).
Link: https://lkml.kernel.org/r/20241219212437.2714151-1-yosryahmed@google.com Fixes: 1ec3b5fe6eec ("mm/zswap: move to use crypto_acomp API for hardware acceleration") Signed-off-by: Yosry Ahmed <yosryahmed@google.com> Reported-by: Johannes Weiner <hannes@cmpxchg.org> Closes: https://lore.kernel.org/lkml/20241113213007.GB1564047@cmpxchg.org/ Reported-by: Sam Sun <samsun1006219@gmail.com> Closes: https://lore.kernel.org/lkml/CAEkJfYMtSdM5HceNsXUDf5haghD5+o2e7Qv4OcuruL4tPg6OaQ@mail.gmail.com/ Reviewed-by: Chengming Zhou <chengming.zhou@linux.dev> Acked-by: Barry Song <baohua@kernel.org> Reviewed-by: Nhat Pham <nphamcs@gmail.com> Cc: Vitaly Wool <vitalywool@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Dennis Lam [Wed, 18 Dec 2024 02:39:25 +0000 (21:39 -0500)]
ocfs2: fix slab-use-after-free due to dangling pointer dqi_priv
When mounting ocfs2 and then remounting it as read-only, a
slab-use-after-free occurs after the user uses a syscall to
quota_getnextquota. Specifically, sb_dqinfo(sb, type)->dqi_priv is the
dangling pointer.
During the remounting process, the pointer dqi_priv is freed but is never
set as null leaving it to be accessed. Additionally, the read-only option
for remounting sets the DQUOT_SUSPENDED flag instead of setting the
DQUOT_USAGE_ENABLED flags. Moreover, later in the process of getting the
next quota, the function ocfs2_get_next_id is called and only checks the
quota usage flags and not the quota suspended flags.
To fix this, I set dqi_priv to null when it is freed after remounting with
read-only and put a check for DQUOT_SUSPENDED in ocfs2_get_next_id.
[akpm@linux-foundation.org: coding-style cleanups] Link: https://lkml.kernel.org/r/20241218023924.22821-2-dennis.lamerice@gmail.com Fixes: 8f9e8f5fcc05 ("ocfs2: Fix Q_GETNEXTQUOTA for filesystem without quotas") Signed-off-by: Dennis Lam <dennis.lamerice@gmail.com> Reported-by: syzbot+d173bf8a5a7faeede34c@syzkaller.appspotmail.com Tested-by: syzbot+d173bf8a5a7faeede34c@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/6731d26f.050a0220.1fb99c.014b.GAE@google.com/T/ Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
David Hildenbrand [Tue, 17 Dec 2024 19:50:00 +0000 (20:50 +0100)]
fs/proc/task_mmu: fix pagemap flags with PMD THP entries on 32bit
Entries (including flags) are u64, even on 32bit. So right now we are
cutting of the flags on 32bit. This way, for example the cow selftest
complains about:
# ./cow
...
Bail Out! read and ioctl return unmatched results for populated: 0 1
Link: https://lkml.kernel.org/r/20241217195000.1734039-1-david@redhat.com Fixes: 2c1f057e5be6 ("fs/proc/task_mmu: properly detect PM_MMAP_EXCLUSIVE per page of PMD-mapped THPs") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Arnd Bergmann [Tue, 17 Dec 2024 07:18:10 +0000 (08:18 +0100)]
kcov: mark in_softirq_really() as __always_inline
If gcc decides not to inline in_softirq_really(), objtool warns about a
function call with UACCESS enabled:
kernel/kcov.o: warning: objtool: __sanitizer_cov_trace_pc+0x1e: call to in_softirq_really() with UACCESS enabled
kernel/kcov.o: warning: objtool: check_kcov_mode+0x11: call to in_softirq_really() with UACCESS enabled
Mark this as __always_inline to avoid the problem.
Link: https://lkml.kernel.org/r/20241217071814.2261620-1-arnd@kernel.org Fixes: 7d4df2dad312 ("kcov: properly check for softirq context") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Marco Elver <elver@google.com> Cc: Aleksandr Nogikh <nogikh@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Josh Poimboeuf <jpoimboe@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Baolin Wang [Tue, 17 Dec 2024 08:55:39 +0000 (16:55 +0800)]
docs: mm: fix the incorrect 'FileHugeMapped' field
The '/proc/PID/smaps' does not have the 'FileHugeMapped' field to count
the file transparent huge pages, instead, the 'FilePmdMapped' field should
be used. Fix it.
Alessandro Carminati [Tue, 17 Dec 2024 14:20:33 +0000 (14:20 +0000)]
mm/kmemleak: fix sleeping function called from invalid context at print message
Address a bug in the kernel that triggers a "sleeping function called from
invalid context" warning when /sys/kernel/debug/kmemleak is printed under
specific conditions:
- CONFIG_PREEMPT_RT=y
- Set SELinux as the LSM for the system
- Set kptr_restrict to 1
- kmemleak buffer contains at least one item
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 136, name: cat
preempt_count: 1, expected: 0
RCU nest depth: 2, expected: 2
6 locks held by cat/136:
#0: ffff32e64bcbf950 (&p->lock){+.+.}-{3:3}, at: seq_read_iter+0xb8/0xe30
#1: ffffafe6aaa9dea0 (scan_mutex){+.+.}-{3:3}, at: kmemleak_seq_start+0x34/0x128
#3: ffff32e6546b1cd0 (&object->lock){....}-{2:2}, at: kmemleak_seq_show+0x3c/0x1e0
#4: ffffafe6aa8d8560 (rcu_read_lock){....}-{1:2}, at: has_ns_capability_noaudit+0x8/0x1b0
#5: ffffafe6aabbc0f8 (notif_lock){+.+.}-{2:2}, at: avc_compute_av+0xc4/0x3d0
irq event stamp: 136660
hardirqs last enabled at (136659): [<ffffafe6a80fd7a0>] _raw_spin_unlock_irqrestore+0xa8/0xd8
hardirqs last disabled at (136660): [<ffffafe6a80fd85c>] _raw_spin_lock_irqsave+0x8c/0xb0
softirqs last enabled at (0): [<ffffafe6a5d50b28>] copy_process+0x11d8/0x3df8
softirqs last disabled at (0): [<0000000000000000>] 0x0
Preemption disabled at:
[<ffffafe6a6598a4c>] kmemleak_seq_show+0x3c/0x1e0
CPU: 1 UID: 0 PID: 136 Comm: cat Tainted: G E 6.11.0-rt7+ #34
Tainted: [E]=UNSIGNED_MODULE
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0xa0/0x128
show_stack+0x1c/0x30
dump_stack_lvl+0xe8/0x198
dump_stack+0x18/0x20
rt_spin_lock+0x8c/0x1a8
avc_perm_nonode+0xa0/0x150
cred_has_capability.isra.0+0x118/0x218
selinux_capable+0x50/0x80
security_capable+0x7c/0xd0
has_ns_capability_noaudit+0x94/0x1b0
has_capability_noaudit+0x20/0x30
restricted_pointer+0x21c/0x4b0
pointer+0x298/0x760
vsnprintf+0x330/0xf70
seq_printf+0x178/0x218
print_unreferenced+0x1a4/0x2d0
kmemleak_seq_show+0xd0/0x1e0
seq_read_iter+0x354/0xe30
seq_read+0x250/0x378
full_proxy_read+0xd8/0x148
vfs_read+0x190/0x918
ksys_read+0xf0/0x1e0
__arm64_sys_read+0x70/0xa8
invoke_syscall.constprop.0+0xd4/0x1d8
el0_svc+0x50/0x158
el0t_64_sync+0x17c/0x180
%pS and %pK, in the same back trace line, are redundant, and %pS can void
%pK service in certain contexts.
%pS alone already provides the necessary information, and if it cannot
resolve the symbol, it falls back to printing the raw address voiding
the original intent behind the %pK.
Additionally, %pK requires a privilege check CAP_SYSLOG enforced through
the LSM, which can trigger a "sleeping function called from invalid
context" warning under RT_PREEMPT kernels when the check occurs in an
atomic context. This issue may also affect other LSMs.
This change avoids the unnecessary privilege check and resolves the
sleeping function warning without any loss of information.
Link: https://lkml.kernel.org/r/20241217142032.55793-1-acarmina@redhat.com Fixes: 3a6f33d86baa ("mm/kmemleak: use %pK to display kernel pointers in backtrace") Signed-off-by: Alessandro Carminati <acarmina@redhat.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Clément Léger <clement.leger@bootlin.com> Cc: Alessandro Carminati <acarmina@redhat.com> Cc: Eric Chanudet <echanude@redhat.com> Cc: Gabriele Paoloni <gpaoloni@redhat.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The folio refcount may be increased unexpectly through try_get_folio() by
caller such as split_huge_pages. In huge_pmd_unshare(), we use refcount
to check whether a pmd page table is shared. The check is incorrect if
the refcount is increased by the above caller, and this can cause the page
table leaked:
BUG: Bad page state in process sh pfn:109324
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x66 pfn:0x109324
flags: 0x17ffff800000000(node=0|zone=2|lastcpupid=0xfffff)
page_type: f2(table)
raw: 017ffff800000000000000000000000000000000000000000000000000000000
raw: 0000000000000066000000000000000000000000f20000000000000000000000
page dumped because: nonzero mapcount
...
CPU: 31 UID: 0 PID: 7515 Comm: sh Kdump: loaded Tainted: G B 6.13.0-rc2master+ #7
Tainted: [B]=BAD_PAGE
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
Call trace:
show_stack+0x20/0x38 (C)
dump_stack_lvl+0x80/0xf8
dump_stack+0x18/0x28
bad_page+0x8c/0x130
free_page_is_bad_report+0xa4/0xb0
free_unref_page+0x3cc/0x620
__folio_put+0xf4/0x158
split_huge_pages_all+0x1e0/0x3e8
split_huge_pages_write+0x25c/0x2d8
full_proxy_write+0x64/0xd8
vfs_write+0xcc/0x280
ksys_write+0x70/0x110
__arm64_sys_write+0x24/0x38
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0x128
el0t_64_sync_handler+0xc8/0xd0
el0t_64_sync+0x190/0x198
The issue may be triggered by damon, offline_page, page_idle, etc, which
will increase the refcount of page table.
1. The page table itself will be discarded after reporting the
"nonzero mapcount".
2. The HugeTLB page mapped by the page table miss freeing since we
treat the page table as shared and a shared page table will not be
unmapped.
Fix it by introducing independent PMD page table shared count. As
described by comment, pt_index/pt_mm/pt_frag_refcount are used for s390
gmap, x86 pgds and powerpc, pt_share_count is used for x86/arm64/riscv
pmds, so we can reuse the field as pt_share_count.
Link: https://lkml.kernel.org/r/20241216071147.3984217-1-liushixin2@huawei.com Fixes: 39dde65c9940 ("[PATCH] shared page table for hugetlb page") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Ken Chen <kenneth.w.chen@intel.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nanyong Sun <sunnanyong@huawei.com> Cc: Jane Chu <jane.chu@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Yang Erkun [Sat, 14 Dec 2024 09:30:05 +0000 (17:30 +0800)]
maple_tree: reload mas before the second call for mas_empty_area
Change the LONG_MAX in simple_offset_add to 1024, and do latter:
[root@fedora ~]# mkdir /tmp/dir
[root@fedora ~]# for i in {1..1024}; do touch /tmp/dir/$i; done
touch: cannot touch '/tmp/dir/1024': Device or resource busy
[root@fedora ~]# rm /tmp/dir/123
[root@fedora ~]# touch /tmp/dir/1024
[root@fedora ~]# rm /tmp/dir/100
[root@fedora ~]# touch /tmp/dir/1025
touch: cannot touch '/tmp/dir/1025': Device or resource busy
After we delete file 100, actually this is a empty entry, but the latter
create failed unexpected.
mas_alloc_cyclic has two chance to find empty entry. First find the entry
with range range_lo and range_hi, if no empty entry exist, and range_lo >
min, retry find with range min and range_hi. However, the first call
mas_empty_area may mark mas as EBUSY, and the second call for
mas_empty_area will return false directly. Fix this by reload mas before
second call for mas_empty_area.
projects / users / jedix / linux-maple.git / log