iscsi_ibft can use ACPI to find the iBFT entry during bootup,
currently, ISCSI_IBFT depends on ISCSI_IBFT_FIND which is
a X86 legacy way to find the iBFT by searching through the
low memory. This patch changes the dependency so that other
arch like ARM64 can use ISCSI_IBFT as long as the arch supports
ACPI.
ibft_init() needs to use the global variable ibft_addr declared
in iscsi_ibft_find.c. A #ifndef CONFIG_ISCSI_IBFT_FIND is needed
to declare the variable if CONFIG_ISCSI_IBFT_FIND is not selected.
Moving ibft_addr into the iscsi_ibft.c does not work because if
ISCSI_IBFT is selected as a module, the arch/x86/kernel/setup.c won't
be able to find the variable at compile time.
Signed-off-by: Thomas Tai <thomas.tai@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com> Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Acked-by: Tony Cheng <Tony.Cheng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com> Reviewed-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to create an inet family nat chain would not cause
nft_chain_nat.ko module to auto-load due to missing module alias. Add a
proper one with hard-coded family value 1 for the pseudo-family
NFPROTO_INET.
Fixes: d164385ec572 ("netfilter: nat: add inet family nat support") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Oleg noticed that our checking of data.got_token is unsafe in the
cleanup case, and should really use a memory barrier. Use a wmb on the
write side, and a rmb() on the read side. We don't need one in the main
loop since we're saved by set_current_state().
If we raced with somebody else getting an inflight counter we could fail
to get an inflight counter with no sleepers on the list, and thus need
to go to sleep. In this case has_sleepers should be true because we are
now relying on the waker to get our inflight counter for us. And in the
case of spurious wakeups we'd still want this to be the case. So set
has_sleepers to true if we went to sleep to make sure we're woken up the
proper way.
The rule below doesn't work as the kernel raises -ERANGE.
nft add rule netdev nftlb lb01 ip daddr set \
symhash mod 1 map { 0 : 192.168.0.10 } fwd to "eth0"
This patch allows to use the symhash modulus with one
element, in the same way that the other types of hashes and
algorithms that uses the modulus parameter.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After 3 way handshake completes, timeout of new connection is set to
max_retrans (300s) instead of established (5 days).
shortened excerpt from pcap provided:
25.070622 IP (flags [DF], proto TCP (6), length 52)
10.8.5.4.1025 > 10.8.1.2.80: Flags [S], seq 11, win 64240, [wscale 8]
26.070462 IP (flags [DF], proto TCP (6), length 48)
10.8.1.2.80 > 10.8.5.4.1025: Flags [S.], seq 82, ack 12, win 65535, [wscale 3]
27.070449 IP (flags [DF], proto TCP (6), length 40)
10.8.5.4.1025 > 10.8.1.2.80: Flags [.], ack 83, win 512, length 0
Turns out the last_win is of u16 type, but we store the scaled value:
512 << 8 (== 0x20000) becomes 0 window.
The Fixes tag is not correct, as the bug has existed forever, but
without that change all that this causes might cause is to mistake a
window update (to-nonzero-from-zero) for a retransmit.
Fixes: fbcd253d2448b8 ("netfilter: conntrack: lower timeout to RETRANS seconds if window is 0") Reported-by: Jakub Jankowski <shasta@toxcorp.com> Tested-by: Jakub Jankowski <shasta@toxcorp.com> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When firewalld is enabled with ipv4/ipv6 rpfilter, vrf
ipv4/ipv6 packets will be dropped. Vrf device will pass
through netfilter hook twice. One with enslaved device
and another one with l3 master device. So in device may
dismatch witch out device because out device is always
enslaved device.So failed with the check of the rpfilter
and drop the packets by mistake.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a small window where it's possible that we could be working
on an interrupt (queued in the workqueue) and setting up a channel
program (i.e allocating memory, pinning pages, translating address).
This can lead to allocating and freeing the channel program at the
same time and can cause memory corruption.
Let's not call cp_free if we are currently processing a channel program.
The only way we know for sure that we don't have a thread setting
up a channel program is when the state is set to VFIO_CCW_STATE_CP_PENDING.
Thomas and Juliana report a deadlock when running:
(rmmod nf_conntrack_netlink/xfrm_user)
conntrack -e NEW -E &
modprobe -v xfrm_user
They provided following analysis:
conntrack -e NEW -E
netlink_bind()
netlink_lock_table() -> increases "nl_table_users"
nfnetlink_bind()
# does not unlock the table as it's locked by netlink_bind()
__request_module()
call_usermodehelper_exec()
This triggers "modprobe nf_conntrack_netlink" from kernel, netlink_bind()
won't return until modprobe process is done.
"modprobe xfrm_user":
xfrm_user_init()
register_pernet_subsys()
-> grab pernet_ops_rwsem
..
netlink_table_grab()
calls schedule() as "nl_table_users" is non-zero
so modprobe is blocked because netlink_bind() increased
nl_table_users while also holding pernet_ops_rwsem.
"modprobe nf_conntrack_netlink" runs and inits nf_conntrack_netlink:
ctnetlink_init()
register_pernet_subsys()
-> blocks on "pernet_ops_rwsem" thanks to xfrm_user module
both modprobe processes wait on one another -- neither can make
progress.
Switch netlink_bind() to "nowait" modprobe -- this releases the netlink
table lock, which then allows both modprobe instances to complete.
Unfortunately in various MM places "max" means a non inclusive end of
range. free_area_init_nodes max_zone_pfn parameter is one case and
MAX_ORDER is another one (unrelated) that comes by memory.
Reported-by: Zorro Lang <zlang@redhat.com> Fixes: 25078dc1f74b ("powerpc: use mm zones more sensibly") Fixes: 9739ab7eda45 ("powerpc: enable a 30-bit ZONE_DMA for 32-bit pmac") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190625141727.2883-1-aarcange@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.
To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.
We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
and again is misprocessed in the same way.
This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.
TCPM may receive PD messages associated with unknown or unsupported
alternate modes. If that happens, calls to typec_match_altmode()
will return NULL. The tcpm code does not currently take this into
account. This results in crashes.
Unable to handle kernel NULL pointer dereference at virtual address 000001f0
pgd = 41dad9a1
[000001f0] *pgd=00000000
Internal error: Oops: 5 [#1] THUMB2
Modules linked in: tcpci tcpm
CPU: 0 PID: 2338 Comm: kworker/u2:0 Not tainted 5.1.18-sama5-armv7-r2 #6
Hardware name: Atmel SAMA5
Workqueue: 2-0050 tcpm_pd_rx_handler [tcpm]
PC is at typec_altmode_attention+0x0/0x14
LR is at tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm]
...
[<c03fbee8>] (typec_altmode_attention) from [<bf8030fb>]
(tcpm_pd_rx_handler+0xa3b/0xda0 [tcpm])
[<bf8030fb>] (tcpm_pd_rx_handler [tcpm]) from [<c012082b>]
(process_one_work+0x123/0x2a8)
[<c012082b>] (process_one_work) from [<c0120a6d>]
(worker_thread+0xbd/0x3b0)
[<c0120a6d>] (worker_thread) from [<c012431f>] (kthread+0xcf/0xf4)
[<c012431f>] (kthread) from [<c01010f9>] (ret_from_fork+0x11/0x38)
Ignore PD messages if the associated alternate mode is not supported.
Fixes: e9576fe8e605c ("usb: typec: tcpm: Support for Alternate Modes") Cc: stable <stable@vger.kernel.org> Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/1564761822-13984-1-git-send-email-linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 96232cbc6c994 ("usb: typec: tcpm: support get typec and pd
config from device properties"), the 'config' pointer in struct tcpc_dev
is optional when registering a Type-C port. Since it is optional, we have
to check if it is NULL before dereferencing it.
Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Fixes: 96232cbc6c994 ("usb: typec: tcpm: support get typec and pd config from device properties") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Reviewed-by: Jun Li <jun.li@nxp.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/1563979112-22483-1-git-send-email-linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If config tcpm as module, module unload will not remove tcpm dir,
then the next module load will have problem: the rootdir is NULL
but tcpm dir is still there, so tcpm_debugfs_init() will create
tcpm dir again with failure, fix it by remove the tcpm dir if no
children.
Cc: stable@vger.kernel.org # v4.15+ Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging") Signed-off-by: Li Jun <jun.li@nxp.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20190717080646.30421-2-jun.li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80
drivers/usb/core/usb.c:928
Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007
Memory state around the buggy address: ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
A quick look at the yurex_delete() shows that we drop the reference
to the usb_device before releasing any buffers associated with the
device. Delay the reference drop until we have finished the cleanup.
Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.
It turns out that the current version of gfs2_metadata_walker suffers
from multiple problems that can cause gfs2_hole_size to report an
incorrect size. This will confuse fiemap as well as lseek with the
SEEK_DATA flag.
Fix that by changing gfs2_hole_walker to compute the metapath to the
first data block after the hole (if any), and compute the hole size
based on that.
Fixes xfstest generic/490.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Bob Peterson <rpeterso@redhat.com> Cc: stable@vger.kernel.org # v4.18+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c66d4bd110a1f8 ("genirq/affinity: Add new callback for
(re)calculating interrupt sets"), irq_create_affinity_masks() returns
NULL in case of single vector. This change has caused regression on some
drivers, such as lpfc.
The problem is that single vector requests can happen in some generic cases:
1) kdump kernel
2) irq vectors resource is close to exhaustion.
If in that situation the affinity mask for a single vector is not created,
every caller has to handle the special case.
There is no reason why the mask cannot be created, so remove the check for
a single vector and create the mask.
Fixes: c66d4bd110a1f8 ("genirq/affinity: Add new callback for (re)calculating interrupt sets") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190805011906.5020-1-ming.lei@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KBUILD_CFLAGS is very carefully built up in the top level Makefile,
particularly when cross compiling or using different build tools.
Resetting KBUILD_CFLAGS via := assignment is an antipattern.
The comment above the reset mentions that -pg is problematic. Other
Makefiles use `CFLAGS_REMOVE_file.o = $(CC_FLAGS_FTRACE)` when
CONFIG_FUNCTION_TRACER is set. Prefer that pattern to wiping out all of
the important KBUILD_CFLAGS then manually having to re-add them. Seems
also that __stack_chk_fail references are generated when using
CONFIG_STACKPROTECTOR or CONFIG_STACKPROTECTOR_STRONG.
Fixes: 8fc5b4d4121c ("purgatory: core purgatory functionality") Reported-by: Vaibhav Rustagi <vaibhavrustagi@google.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Vaibhav Rustagi <vaibhavrustagi@google.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190807221539.94583-2-ndesaulniers@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementing memcpy and memset in terms of __builtin_memcpy and
__builtin_memset is problematic.
GCC at -O2 will replace calls to the builtins with calls to memcpy and
memset (but will generate an inline implementation at -Os). Clang will
replace the builtins with these calls regardless of optimization level.
$ llvm-objdump -dr arch/x86/purgatory/string.o | tail
Such code results in infinite recursion at runtime. This is observed
when doing kexec.
Instead, reuse an implementation from arch/x86/boot/compressed/string.c.
This requires to implement a stub function for warn(). Also, Clang may
lower memcmp's that compare against 0 to bcmp's, so add a small definition,
too. See also: commit 5f074f3e192f ("lib/string.c: implement a basic bcmp")
There is an offset of 0x1990 bytes. The size of the qeth module is
151552 bytes (0x25000 in hex).
The location of the GOT/relocation table at the beginning of a module is
unique to s390.
commit 203d8a4aa6ed ("perf s390: Fix 'start' address of module's map")
adjusts the start address of a module in the map structures, but does
not adjust the size of the modules. This leads to overlapping of module
maps as this example shows:
The module qeth.ko has an adjusted start address modified to b3990, but
its size is unchanged and the module ends at 0x3ff800d8990. This end
address overlaps with the next modules start address of 0x3ff800d85a0.
When the size of the leading GOT/Relocation table stored in the
beginning of the text segment (0x1990 bytes) is subtracted from module
qeth end address, there are no overlaps anymore:
0x3ff800d8990 - 0x1990 = 0x0x3ff800d7000
which is the same as
0x3ff800b2000 + 0x25000 = 0x0x3ff800d7000.
To fix this issue, also adjust the modules size in function
arch__fix_module_text_start(). Add another function parameter named size
and reduce the size of the module when the text segment start address is
changed.
Threads synthesized from /proc have comms with a start time of zero, and
not marked as "exec". Currently, there can be 2 such comms. The first is
created by processing a synthesized fork event and is set to the
parent's comm string, and the second by processing a synthesized comm
event set to the thread's current comm string.
In the absence of an "exec" comm, thread__exec_comm() picks the last
(oldest) comm, which, in the case above, is the parent's comm string.
For a main thread, that is very probably wrong. Use the second-to-last
in that case.
This affects only db-export because it is the only user of
thread__exec_comm().
Example:
$ sudo perf record -a -o pt-a-sleep-1 -e intel_pt//u -- sleep 1
$ sudo chown ahunter pt-a-sleep-1
On s390 the kernel is located around memory address 0x200, 0x10000 or
0x100000, depending on linux version. Modules however start some- where
around 0x3ff xxxx xxxx.
This is different than x86 and produces a large gap for which histogram
allocation fails.
Fix this by detecting the kernel's last symbol and do no adjustment for
it. Introduce a weak function and handle s390 specifics.
Reported-by: Klaus Theurich <klaus.theurich@de.ibm.com> Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20190724122703.3996-2-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On x86-32 with PTI enabled, parts of the kernel page-tables are not shared
between processes. This can cause mappings in the vmalloc/ioremap area to
persist in some page-tables after the region is unmapped and released.
When the region is re-used the processes with the old mappings do not fault
in the new mappings but still access the old ones.
This causes undefined behavior, in reality often data corruption, kernel
oopses and panics and even spontaneous reboots.
Fix this problem by activly syncing unmaps in the vmalloc/ioremap area to
all page-tables in the system before the regions can be re-used.
References: https://bugzilla.suse.com/show_bug.cgi?id=1118689 Fixes: 5d72b4fba40ef ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-4-joro@8bytes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With huge-page ioremap areas the unmappings also need to be synced between
all page-tables. Otherwise it can cause data corruption when a region is
unmapped and later re-used.
Make the vmalloc_sync_one() function ready to sync unmappings and make sure
vmalloc_sync_all() iterates over all page-tables even when an unmapped PMD
is found.
Fixes: 5d72b4fba40ef ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-3-joro@8bytes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not require a struct page for the mapped memory location because it
might not exist. This can happen when an ioremapped region is mapped with
2MB pages.
Fixes: 5d72b4fba40ef ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-2-joro@8bytes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2016 kabylake HP Spectre X360 (model number 13-w013dx) works much better
with psmouse.synaptics_intertouch=1 kernel parameter, so let's enable RMI4
mode automatically.
There are some new HP laptops with Elantech touchpad that don't support
multitouch.
Currently we use ETP_NEW_IC_SMBUS_HOST_NOTIFY() to check if SMBus is supported,
but in addition to firmware version, the bus type also informs us whether the IC
can support SMBus. To avoid breaking old ICs, we will only enable SMbus support
based the bus type on systems manufactured after 2018.
Lastly, let's consolidate all checks into elantech_use_host_notify() and use it
to determine whether to use PS/2 or SMBus.
Commit 89e524c04fa9 ("loop: Fix mount(2) failure due to race with
LOOP_SET_FD") converted blkdev_get() to use the new helpers for
finishing claiming of a block device. However the conversion botched the
error handling in blkdev_get() and thus the bdev has been marked as held
even in case __blkdev_get() returned error. This led to occasional
warnings with block/001 test from blktests like:
kernel: WARNING: CPU: 5 PID: 907 at fs/block_dev.c:1899 __blkdev_put+0x396/0x3a0
Correct the error handling.
CC: stable@vger.kernel.org Fixes: 89e524c04fa9 ("loop: Fix mount(2) failure due to race with LOOP_SET_FD") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have set the mmc_host.max_seg_size to 8M, but the dma max segment
size of PCI device is set to 64K by default in function pci_device_add().
The mmc_host.max_seg_size is used to set the max segment size of
the blk queue. Then this mismatch will trigger a calltrace like below
when a bigger than 64K segment request arrives at mmc dev. So we should
consider the limitation of the cvm_mmc_host when setting the
mmc_host.max_seg_size.
DMA-API: thunderx_mmc 0000:01:01.4: mapping sg segment longer than device claims to support [len=131072] [max=65536]
WARNING: CPU: 6 PID: 238 at kernel/dma/debug.c:1221 debug_dma_map_sg+0x2b8/0x350
Modules linked in:
CPU: 6 PID: 238 Comm: kworker/6:1H Not tainted 5.3.0-rc1-next-20190724-yocto-standard+ #62
Hardware name: Marvell OcteonTX CN96XX board (DT)
Workqueue: kblockd blk_mq_run_work_fn
pstate: 80c00009 (Nzcv daif +PAN +UAO)
pc : debug_dma_map_sg+0x2b8/0x350
lr : debug_dma_map_sg+0x2b8/0x350
sp : ffff00001770f9e0
x29: ffff00001770f9e0 x28: ffffffff00000000
x27: 00000000ffffffff x26: ffff800bc2c73180
x25: ffff000010e83700 x24: 0000000000000002
x23: 0000000000000001 x22: 0000000000000001
x21: 0000000000000000 x20: ffff800bc48ba0b0
x19: ffff800bc97e8c00 x18: ffffffffffffffff
x17: 0000000000000000 x16: 0000000000000000
x15: ffff000010e835c8 x14: 6874207265676e6f
x13: 6c20746e656d6765 x12: 7320677320676e69
x11: 7070616d203a342e x10: 31303a31303a3030
x9 : 303020636d6d5f78 x8 : 35363d78616d5b20
x7 : 00000000000002fd x6 : ffff000010fd57dc
x5 : 0000000000000000 x4 : ffff0000106c61f0
x3 : 00000000ffffffff x2 : 0000800bee060000
x1 : 7010678df3041a00 x0 : 0000000000000000
Call trace:
debug_dma_map_sg+0x2b8/0x350
cvm_mmc_request+0x3c4/0x988
__mmc_start_request+0x9c/0x1f8
mmc_start_request+0x7c/0xb0
mmc_blk_mq_issue_rq+0x5c4/0x7b8
mmc_mq_queue_rq+0x11c/0x278
blk_mq_dispatch_rq_list+0xb0/0x568
blk_mq_do_dispatch_sched+0x6c/0x108
blk_mq_sched_dispatch_requests+0x110/0x1b8
__blk_mq_run_hw_queue+0xb0/0x118
blk_mq_run_work_fn+0x28/0x38
process_one_work+0x210/0x490
worker_thread+0x48/0x458
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
In sound_insert_unit(), the controlling structure 's' is allocated through
kmalloc(). Then it is added to the sound driver list by invoking
__sound_insert_unit(). Later on, if __register_chrdev() fails, 's' is
removed from the list through __sound_remove_unit(). If 'index' is not less
than 0, -EBUSY is returned to indicate the error. However, 's' is not
deallocated on this execution path, leading to a memory leak bug.
To fix the above issue, free 's' before -EBUSY is returned.
We have to drop the mutex before we close() upon disconnect()
as close() needs the lock. This is safe to do by dropping the
mutex as intfdata is already set to NULL, so open() will fail.
Fixes: 03f36e885fc26 ("USB: open disconnect race in iowarrior") Reported-by: syzbot+a64a382964bf6c71a9c0@syzkaller.appspotmail.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190808092728.23417-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon an error within proc_do_submiturb(), dec_usb_memory_use_count()
gets called once by the error handling tail and again by free_async().
Remove the first call.
Commit daaef255dc96 ("driver: platform: Support parsing GpioInt 0 in
platform_get_irq()") broke the Embedded Controller driver on most LPC
Chromebooks (i.e., most x86 Chromebooks), because cros_ec_lpc expects
platform_get_irq() to return -ENXIO for non-existent IRQs.
Unfortunately, acpi_dev_gpio_irq_get() doesn't follow this convention
and returns -ENOENT instead. So we get this error from cros_ec_lpc:
couldn't retrieve IRQ number (-2)
I see a variety of drivers that treat -ENXIO specially, so rather than
fix all of them, let's fix up the API to restore its previous behavior.
and the result is that the bug landed and remains unfixed.
I differ from the v3 patch by:
* allowing for ret==0, even though acpi_dev_gpio_irq_get() specifically
documents (and enforces) that 0 is not a valid return value (noted on
the v3 review)
* adding a small comment
Reported-by: Brian Norris <briannorris@chromium.org> Reported-by: Salvatore Bellizzi <salvatore.bellizzi@linux.seppia.net> Cc: Enrico Granata <egranata@chromium.org> Cc: <stable@vger.kernel.org> Fixes: daaef255dc96 ("driver: platform: Support parsing GpioInt 0 in platform_get_irq()") Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Enrico Granata <egranata@google.com> Link: https://lore.kernel.org/r/20190729204954.25510-1-briannorris@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AES GCM input buffers for decryption contain AAD+CTEXT+TAG. Only
decrypt the ciphertext, and use the tag for comparison.
Fixes: 36cf515b9bbe2 ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AES GCM encryption allows for authsize values of 4, 8, and 12-16 bytes.
Validate the requested authsize, and retain it to save in the request
context.
Fixes: 36cf515b9bbe2 ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A plaintext or ciphertext length of 0 is allowed in AES, in which case
no encryption occurs. Ensure that we don't clean up data structures
that were never allocated.
Fixes: 36cf515b9bbe2 ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typically gpiod_set_value calls would assert the reset line and
then release it using the symantics of:
gpiod_set_value(par->gpio.reset, 0);
... delay
gpiod_set_value(par->gpio.reset, 1);
And the gpio binding would specify the polarity.
Prior to conversion to gpiod calls the polarity in the DT
was ignored and assumed to be active low. Fix it so that
DT polarity is respected.
Fixes: c440eee1a7a1 ("Staging: fbtft: Switch to the gpio descriptor interface") Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Jan Sebastian Götte <linux@jaseg.net> Signed-off-by: Phil Reid <preid@electromag.com.au> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1563236677-5045-3-git-send-email-preid@electromag.com.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conversion to use gpio descriptors broke all gpio lookups as
devm_gpiod_get_index was converted to use dev->driver->name for
the gpio name lookup. Fix this by using the name param. In
addition gpiod_get post-fixes the -gpios to the name so that
shouldn't be included in the call. However this then breaks the
of_find_property call to see if the gpio entry exists as all
fbtft treats all gpios as optional. So use devm_gpiod_get_index_optional
instead which achieves the same thing and is simpler.
Nishad confirmed the changes where only ever compile tested.
Fixes: c440eee1a7a1 ("Staging: fbtft: Switch to the gpio descriptor interface") Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Jan Sebastian Götte <linux@jaseg.net> Signed-off-by: Phil Reid <preid@electromag.com.au> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1563236677-5045-2-git-send-email-preid@electromag.com.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot found that a thread can stall for minutes inside
ion_system_heap_allocate() after that thread was killed by SIGKILL [1].
Let's check for SIGKILL before doing memory allocation.
In sysfs_show() case-branches ATTR_KERNEL_HIB_PAGE_TABLE_SIZE and
ATTR_KERNEL_HIB_SIMPLE_PAGE_TABLE_SIZE do the same. It looks like
copy-paste mistake.
Driver only supports 3-axis gyro and/or 3-axis accel.
For icm20602, temp data is mandatory for all configurations.
Fix all single and double axis configurations (almost never used) and more
importantly fix 3-axis gyro and 6-axis accel+gyro buffer on icm20602 when
temp data is not enabled.
The SADC component can run at up to 8 MHz on JZ4725B, but is fed
a 12 MHz input clock (EXT). Divide it by two to get 6 MHz, then
set up another divider to match, to produce a 10us clock.
If the clock dividers are left on their power-on defaults (a divider
of 1), the SADC mostly works, but will occasionally produce erroneous
readings. This led to button presses being detected out of nowhere on
the RS90 every few minutes. With this change, no ghost button presses
were logged in almost a day worth of testing.
The ADCLK register for configuring clock dividers doesn't exist on
JZ4740, so avoid writing it there.
A function has been introduced rather than a flag because there is a lot
of variation between the ADCLK registers on JZ47xx SoCs, both in
the internal layout of the register and in the frequency range
supported by the SADC. So this solution should make it easier
to add support for other JZ47xx SoCs later.
Fixes: 1a78daea107d ("iio: adc: probe should set clock divider") Signed-off-by: Maarten ter Huurne <maarten@treewalker.org> Signed-off-by: Artur Rojek <contact@artur-rojek.eu> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c2bf1fc212f7 ("PCI: Add missing link delays required by the PCIe
spec") turned out causing issues with some systems either by making them
unresponsive or slowing down runtime and system wide resume of PCIe
devices. While root cause for the unresponsiveness is still under
investigation given the amount of issues reported better to revert it
for now.
Commit 6935224da248 ("spi: bcm2835: enable support of 3-wire mode")
added 3-wire support to the BCM2835 SPI driver by setting the REN bit
(Read Enable) in the CS register when receiving data. The REN bit puts
the transmitter in high-impedance state. The driver recognizes that
data is to be received by checking whether the rx_buf of a transfer is
non-NULL.
Commit 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers
meeting certain conditions") subsequently broke 3-wire support because
it set the SPI_MASTER_MUST_RX flag which causes spi_map_msg() to replace
rx_buf with a dummy buffer if it is NULL. As a result, rx_buf is
*always* non-NULL if DMA is enabled.
Reinstate 3-wire support by not only checking whether rx_buf is non-NULL,
but also checking that it is not the dummy buffer.
Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions") Reported-by: Nuno Sá <nuno.sa@analog.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.2+ Cc: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/328318841455e505370ef8ecad97b646c033dc8a.1562148527.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert this for now, it has been reported multiple times that it
completely breaks connectivity on various devices.
Cc: stable@vger.kernel.org Fixes: 8dbb000ee73b ("mac80211: set NETIF_F_LLTX when using intermediate tx queues") Reported-by: Jean Delvare <jdelvare@suse.de> Reported-by: Peter Lebbing <peter@digitalbrains.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A single 32-bit PSR2 training pattern field follows the sixteen element
array of PSR table entries in the VBT spec. But, we incorrectly define
this PSR2 field for each of the PSR table entries. As a result, the PSR1
training pattern duration for any panel_type != 0 will be parsed
incorrectly. Secondly, PSR2 training pattern durations for VBTs with bdb
version >= 226 will also be wrong.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: stable@vger.kernel.org Cc: stable@vger.kernel.org #v5.2 Fixes: 88a0d9606aff ("drm/i915/vbt: Parse and use the new field with PSR2 TP2/3 wakeup time")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111088
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204183 Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Tested-by: François Guerraz <kubrick@fgv6.net> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190717223451.2595-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit b5ea9c9337007d6e700280c8a60b4e10d070fb53) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.
Guillaume Nault adds:
And the implementation was broken until 2016 (see 29e73269aa4d ("pppoe:
fix reference counting in PPPoE proxy")), and nobody ever noticed. I
should probably have removed this ioctl entirely instead of fixing it.
Clearly, it has never been used.
Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.
All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.
This should apply to all stable kernels.
Acked-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speed translation is performed based on legacy or extended PTYS
register. Translate speed with respect to:
1) Capability bit of extended PTYS table.
2) User request:
a) When auto-negotiation is turned on, inspect advertisement whether it
contains extended link modes.
b) When auto-negotiation is turned off, speed > 100Gbps (maximal
speed supported in legacy mode).
With both conditions fulfilled translation is done with extended PTYS
table otherwise use legacy PTYS table.
Without this patch 25/50/100 Gbps speed cannot be set, since try to
configure in extended mode but read from legacy mode.
New flow table type RDMA_RX was added but the MLX5_CAP_FLOW_TABLE_TYPE
didn't handle this new flow table type.
This means that MLX5_CAP_FLOW_TABLE_TYPE returns an empty capability to
this flow table type.
Update both the macro and the maximum supported flow table type to
RDMA_RX.
Fixes: d83eb50e29de ("net/mlx5: Add support in RDMA RX steering") Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit e891ce1dd2a5 ("mlxsw: spectrum_buffers: Reduce pool size on
Spectrum-2"), pool size was reduced to mitigate a problem in port buffer
usage of ports split four ways. It turns out that this work around does not
solve the issue, and a further reduction is required.
Thus reduce the size of pool 0 by another 2.7 MiB, and round down to the
whole number of cells.
Fixes: e891ce1dd2a5 ("mlxsw: spectrum_buffers: Reduce pool size on Spectrum-2") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there are two error return paths that leak memory allocated
to fib_work. Fix this by kfree'ing fib_work before returning.
Addresses-Coverity: ("Resource leak") Fixes: 19a9d136f198 ("ipv4: Flag fib_info with a fib_nh using IPv6 gateway") Fixes: dbcc4fa718ee ("rocker: Fail attempts to use routes with nexthop objects") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FASTOPEN is not possible with SMC. sendmsg() with msg_flag MSG_FASTOPEN
triggers a fallback to TCP if the socket is in state SMC_INIT.
But if a nonblocking connect is already started, fallback to TCP
is no longer possible, even though the socket may still be in state
SMC_INIT.
And if a nonblocking connect is already started, a listen() call
does not make sense.
Reported-by: syzbot+bd8cc73d665590a1fcad@syzkaller.appspotmail.com Fixes: 50717a37db032 ("net/smc: nonblocking connect rework") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
There is a race condition for an established connection that is being closed
by the guest: the refcnt is 4 at the end of hvs_release() (Note: here the
'remove_sock' is false):
1 for the initial value;
1 for the sk being in the bound list;
1 for the sk being in the connected list;
1 for the delayed close_work.
After hvs_release() finishes, __vsock_release() -> sock_put(sk) *may*
decrease the refcnt to 3.
Concurrently, hvs_close_connection() runs in another thread:
calls vsock_remove_sock() to decrease the refcnt by 2;
call sock_put() to decrease the refcnt to 0, and free the sk;
next, the "release_sock(sk)" may hang due to use-after-free.
In the above, after hvs_release() finishes, if hvs_close_connection() runs
faster than "__vsock_release() -> sock_put(sk)", then there is not any issue,
because at the beginning of hvs_close_connection(), the refcnt is still 4.
The issue can be resolved if an extra reference is taken when the
connection is established.
Fixes: a9eeb998c28d ("hv_sock: Add support for delayed close") Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Sunil Muthuswamy <sunilmut@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generic-XDP was moved to a later processing step by commit 458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
a regression was introduced when using bpf_xdp_adjust_head.
The issue is that after this commit the skb->network_header is now
changed prior to calling generic XDP and not after. Thus, if the header
is changed by XDP (via bpf_xdp_adjust_head), then skb->network_header
also need to be updated again. Fix by calling skb_reset_network_header().
Fixes: 458bf2f224f0 ("net: core: support XDP generic on stacked devices.") Reported-by: Brandon Cazander <brandon.cazander@multapplied.net> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Given the increasing number of BPF selftests, it makes sense to
reduce the time to execute these tests. The ping parameters are
adjusted to reduce the time from measures 9 sec to approx 2.8 sec.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In-order to test both native-XDP (xdpdrv) and generic-XDP (xdpgeneric)
create two wrapper test scripts, that start the test_xdp_vlan.sh script
with these modes.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change BPF selftest test_xdp_vlan.sh to (default) use generic XDP.
This selftest was created together with a fix for generic XDP, in commit 297249569932 ("net: fix generic XDP to handle if eth header was
mangled"). And was suppose to catch if generic XDP was broken again.
The tests are using veth and assumed that veth driver didn't support
native driver XDP, thus it used the (ip link set) 'xdp' attach that fell
back to generic-XDP. But veth gained native-XDP support in 948d4f214fde
("veth: Add driver XDP"), which caused this test script to use
native-XDP.
Fixes: 948d4f214fde ("veth: Add driver XDP") Fixes: 97396ff0bc2d ("selftests/bpf: add XDP selftests for modifying and popping VLAN headers") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.
This patch prevents a race between user invoked cached counters
query and a neighbor last usage updater.
The cached flow counter stats can be queried by calling
"mlx5_fc_query_cached" which provides the number of bytes and
packets that passed via this flow since the last time this counter
was queried.
It does so by reducting the last saved stats from the current, cached
stats and then updating the last saved stats with the cached stats.
It also provide the lastuse value for that flow.
Since "mlx5e_tc_update_neigh_used_value" needs to retrieve the
last usage time of encapsulation flows, it calls the flow counter
query method periodically and async to user queries of the flow counter
using cls_flower.
This call is causing the driver to update the last reported bytes and
packets from the cache and therefore, future user queries of the flow
stats will return lower than expected number for bytes and packets
since the last saved stats in the driver was updated async to the last
saved stats in cls_flower.
This causes wrong stats presentation of encapsulation flows to user.
Since the neighbor usage updater only needs the lastuse stats from the
cached counter, the fix is to use a dedicated lastuse query call that
returns the lastuse value without synching between the cached stats and
the last saved stats.
Fixes: f6dfb4c3f216 ("net/mlx5e: Update neighbour 'used' state using HW flow rules counters") Signed-off-by: Ariel Levkovich <lariel@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- v1 -> v2: Move skb_set_owner_w to __tun_build_skb to reduce patch size
Small packets going out of a tap device go through an optimized code
path that uses build_skb() rather than sock_alloc_send_pskb(). The
latter calls skb_set_owner_w(), but the small packet code path does not.
The net effect is that small packets are not owned by the userland
application's socket (e.g. QEMU), while large packets are.
This can be seen with a TCP session, where packets are not owned when
the window size is small enough (around PAGE_SIZE), while they are once
the window grows (note that this requires the host to support virtio
tso for the guest to offload segmentation).
All this leads to inconsistent behaviour in the kernel, especially on
netfilter modules that uses sk->socket (e.g. xt_owner).
Fixes: 66ccbc9c87c2 ("tap: use build_skb() for small packet") Signed-off-by: Alexis Bauvin <abauvin@scaleway.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is that the skb list tipc_socket::mc_method.deferredq only
is initialized for connectionless sockets, while nothing stops arriving
multicast messages from being filtered by connection oriented sockets,
with subsequent access to the said list.
We fix this by initializing the list unconditionally at socket creation.
This eliminates the crash, while the message still is dropped further
down in tipc_sk_filter_rcv() as it should be.
Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2753ca5d9009 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
Fix two reset-gpio sanity checks which were never converted to use
gpio_is_valid(), and make sure to use -EINVAL to indicate a missing
reset line also for the UART-driver module parameter and for the USB
driver.
This specifically prevents the UART and USB drivers from incidentally
trying to request and use gpio 0, and also avoids triggering a WARN() in
gpio_to_desc() during probe when no valid reset line has been specified.
projects / users / dwmw2 / linux.git / log