Since the commit 0cf4503174c1 ("dm raid: add support for the MD RAID0
personality"), the dm-raid subsystem can activate a RAID-0 array.
Therefore, add MD_RAID0 to the dependencies of DM_RAID, so that MD_RAID0
will be selected when DM_RAID is selected.
Fixes: 0cf4503174c1 ("dm raid: add support for the MD RAID0 personality") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm_btree_find_lowest_key() is giving incorrect results. find_key()
traverses the btree correctly for finding the highest key, but there is
an error in the way it traverses the btree for retrieving the lowest
key. dm_btree_find_lowest_key() fetches the first key of the rightmost
block of the btree instead of fetching the first key from the leftmost
block.
Fix this by conditionally passing the correct parameter to value64()
based on the @find_highest flag.
Signed-off-by: Erez Zadok <ezk@fsl.cs.sunysb.edu> Signed-off-by: Vinothkumar Raja <vinraja@cs.stonybrook.edu> Signed-off-by: Nidhi Panpalia <npanpalia@cs.stonybrook.edu> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The infiniband address handle can be triggered to resolve an ipv6
address in response to MAD packets, regardless of the ipv6
module being disabled via the kernel command line argument.
That will cause a call into the ipv6 routing code, which is not
initialized, and a conseguent oops.
This commit addresses the above issue replacing the direct lookup
call with an indirect one via the ipv6 stub, which is properly
initialized according to the ipv6 status (e.g. if ipv6 is
disabled, the routing lookup fails gracefully)
Make sure size of response buffer is at least 6 bytes, or
we will underflow and pass large size_t to memcpy_fromio().
This was encountered while testing earlier version of
locality patchset.
Fixes: 30fc8d138e912 ("tpm: TPM 2.0 CRB Interface") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there is an unnecessary 1 msec delay added in
i2c_nuvoton_write_status() for the successful case. This
function is called multiple times during send() and recv(),
which implies adding multiple extra delays for every TPM
operation.
This patch calls usleep_range() only if retry is to be done.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com> Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 500462a9de65 "timers: Switch to a non-cascading wheel" replaced
the 'classic' timer wheel, which aimed for near 'exact' expiry of the
timers. Their analysis was that the vast majority of timeout timers
are used as safeguards, not as real timers, and are cancelled or
rearmed before expiration. The only exception noted to this were
networking timers with a small expiry time.
Not included in the analysis was the TPM polling timer, which resulted
in a longer normal delay and, every so often, a very long delay. The
non-cascading wheel delay is based on CONFIG_HZ. For a description of
the different rings and their delays, refer to the comments in
kernel/time/timer.c.
Below are the delays given for rings 0 - 2, which explains the longer
"normal" delays and the very, long delays as seen on systems with
CONFIG_HZ 250.
* HZ 1000 steps
* Level Offset Granularity Range
* 0 0 1 ms 0 ms - 63 ms
* 1 64 8 ms 64 ms - 511 ms
* 2 128 64 ms 512 ms - 4095 ms (512ms - ~4s)
* HZ 250
* Level Offset Granularity Range
* 0 0 4 ms 0 ms - 255 ms
* 1 64 32 ms 256 ms - 2047 ms (256ms - ~2s)
* 2 128 256 ms 2048 ms - 16383 ms (~2s - ~16s)
Below is a comparison of extending the TPM with 1000 measurements,
using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250
hz, before and after commit 500462a9de65.
Testing the implementation with a Raspberry Pi 2 showed that under some
circumstances its SPI master erroneously releases the CS line before the
transfer is complete, i.e. before the end of the last clock. In this case
the TPM ignores the transfer and misses for example the GO command. The
driver is unable to detect this communication problem and will wait for a
command response that is never going to arrive, timing out eventually.
As a workaround, the small delay ensures that the CS line is held long
enough, even with a faulty SPI master. Other SPI masters are not affected,
except for a negligible performance penalty.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Limiting transfers to MAX_SPI_FRAMESIZE was not expected by the upper
layers, as tpm_tis has no such limitation. Add a loop to hide that
limitation.
v2: Moved scope of spi_message to the top as requested by Jarkko Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abort the transfer with ETIMEDOUT when the TPM signals more than
TPM_RETRY wait states. Continuing with the transfer in this state
will only lead to arbitrary failures in other parts of the code.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The algorithm for sending data to the TPM is mostly identical to the
algorithm for receiving data from the TPM, so a single function is
sufficient to handle both cases.
This is a prequisite for all the other fixes, so we don't have to fix
everything twice (send/receive)
v2: u16 instead of u8 for the length. Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Benoit Houyere <benoit.houyere@st.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When delivering an event to userspace for a file on an NFS share,
if the file is deleted on server side before user reads the event,
user will not get the event.
If the event queue contained several events, the stale event is
quietly dropped and read() returns to user with events read so far
in the buffer.
If the event queue contains a single stale event or if the stale
event is a permission event, read() returns to user with the kernel
internal error code 518 (EOPENSTALE), which is not a POSIX error code.
Check the internal return value -EOPENSTALE in fanotify_read(), just
the same as it is checked in path_openat() and drop the event in the
cases that it is not already dropped.
This is a reproducer from Marko Rauhamaa:
Just take the example program listed under "man fanotify" ("fantest")
and follow these steps:
==============================================================
NFS Server NFS Client(1) NFS Client(2)
==============================================================
# echo foo >/nfsshare/bar.txt
# cat /nfsshare/bar.txt
foo
# ./fantest /nfsshare
Press enter key to terminate.
Listening for events.
# rm -f /nfsshare/bar.txt
# cat /nfsshare/bar.txt
read: Unknown error 518
cat: /nfsshare/bar.txt: Operation not permitted
==============================================================
where NFS Client (1) and (2) are two terminal sessions on a single NFS
Client machine.
Reported-by: Marko Rauhamaa <marko.rauhamaa@f-secure.com> Tested-by: Marko Rauhamaa <marko.rauhamaa@f-secure.com> Cc: <linux-api@vger.kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using jiffies in hdac_wait_for_cmd_dmas() to determine when to time out
when interrupts are off (snd_hdac_bus_stop_cmd_io()/spin_lock_irq())
causes hard lockup so unlock while waiting using jiffies.
TIS v1.3 for TPM 1.2 and PTP for TPM 2.0 disagree about which timeout
value applies to reading a valid burstcount. It is TIMEOUT_D according to
TIS, but TIMEOUT_A according to PTP, so choose the appropriate value
depending on whether we deal with a TPM 1.2 or a TPM 2.0.
This is important since according to the PTP TIMEOUT_D is much smaller
than TIMEOUT_A. So the previous implementation could run into timeouts
with a TPM 2.0, even though the TPM was behaving perfectly fine.
During tpm2_probe TIMEOUT_D will be used even with a TPM 2.0, because
TPM_CHIP_FLAG_TPM2 is not yet set. This is fine, since the timeout values
will only be changed afterwards by tpm_get_timeouts. Until then
TIS_TIMEOUT_D_MAX applies, which is large enough.
Fixes: aec04cbdf723 ("tpm: TPM 2.0 FIFO Interface") Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Peter Huewe <peter.huewe@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]
The lp_setup() code doesn't apply any bounds checking when passing
"lp=none", and only in this case, resulting in an overflow of the
parport_nr[] array. All versions in Git history are affected.
Reported-By: Roee Hay <roee.hay@hcl.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ene_usb6250 sub-driver in usb-storage does USB I/O to buffers on
the stack, which doesn't work with vmapped stacks. This patch fixes
the problem by allocating a separate 512-byte buffer at probe time and
using it for all of the offending I/O operations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When built as a module and running with update_ms >= 0, pstore will Oops
during module unload since the work timer is still running. This makes sure
the worker is stopped before unloading.
After commit c950fd6f201a kernel registers pstore write based on flag set.
Pstore write for powerpc is broken as flags(PSTORE_FLAGS_DMESG) is not set for
powerpc architecture. On panic, kernel doesn't write message to
/fs/pstore/dmesg*(Entry doesn't gets created at all).
This patch enables pstore write for powerpc architecture by setting
PSTORE_FLAGS_DMESG flag.
In commit 658922e57b84 "libnvdimm, pfn: fix memmap reservation sizing"
we arranged for the capacity to be allocated, but failed to also update
the 'npfns' parameter. This leads to cases where there is enough
capacity reserved to hold all the allocated sections, but
vmemmap_populate_hugepages() still encounters -ENOMEM from
altmap_alloc_block_buf().
This fix is a stop-gap until we can teach the core memory hotplug
implementation to permit sub-section hotplug.
Fixes: 658922e57b84 ("libnvdimm, pfn: fix memmap reservation sizing") Reported-by: Anisha Allada <anisha.allada@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where a dimm does not have any associated flush hints the
ndrd->flush_wpq array may be uninitialized leading to crashes with the
following signature:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: region_visible+0x10f/0x160 [libnvdimm]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Fixes: f284a4f23752 ("libnvdimm: introduce nvdimm_flush() and nvdimm_has_flush()") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msg_written_handler() may set ssif_info->multi_data to NULL
when using ipmitool to write fru.
Before setting ssif_info->multi_data to NULL, add new local
pointer "data_to_send" and store correct i2c data pointer to
it to fix NULL pointer kernel panic and incorrect ssif_info->multi_pos.
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Make sure to check the tty-device pointer before looking up the sibling
platform device to avoid dereferencing a NULL-pointer when the tty is
one end of a Unix98 pty.
Running 32bit userspace on 64bit kernel results in MSG_CMSG_COMPAT being
defined as 0x80000000. This results in sendmsg failure if used from 32bit
userspace running on 64bit kernel. Fix this by accounting for MSG_CMSG_COMPAT
in flags check in hci_sock_sendmsg.
While using emacs, cat or others' commands in konsole with recent
kernels, I have met many times that CTRL-C freeze konsole. After
konsole freeze I can't type anything, then I have to open a new one,
it is very annoying.
See bug report:
https://bugs.kde.org/show_bug.cgi?id=175283
The platform in that bug report is Solaris, but now the pty in linux
has the same problem or the same behavior as Solaris :)
It has high possibility to trigger the problem follow steps below:
Note: In my test, BigFile is a text file whose size is bigger than 1G
1:open konsole
1:cat BigFile
2:CTRL-C
After some digging, I find out the reason is that commit 1d1d14da12e7
("pty: Fix buffer flush deadlock") changes the behavior of pty_flush_buffer.
Thread A Thread B
-------- --------
1:n_tty_poll return POLLIN
2:CTRL-C trigger pty_flush_buffer
tty_buffer_flush
n_tty_flush_buffer
3:attempt to check count of chars:
ioctl(fd, TIOCINQ, &available)
available is equal to 0
4:read(fd, buffer, avaiable)
return 0
5:konsole close fd
Yes, I know we could use the same patch included in the BUG report as
a workaround for linux platform too. But I think the data in ldisc is
belong to application of another side, we shouldn't clear it when we
want to flush write buffer of this side in pty_flush_buffer. So I think
it is better to disable ldisc flush in pty_flush_buffer, because its new
hehavior bring no benefit except that it mess up the behavior between
POLLIN, and TIOCINQ or FIONREAD.
Also I find no flush_buffer function in others' tty driver has the
same behavior as current pty_flush_buffer.
Make sure to actually suspend the device before returning after a failed
(or deferred) probe.
Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.
Fixes: 388bc2622680 ("omap-serial: Fix the error handling in the omap_serial probe") Cc: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)
Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.
Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.
Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.
Fixes: 7e9c8e7dbf3b ("serial: omap: make sure to suspend device before remove") Cc: Felipe Balbi <balbi@kernel.org> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver should provide its own struct device for all DMA-mapping calls instead
of extracting device pointer from DMA engine channel. Although this is harmless
from the driver operation perspective on ARM architecture, it is always good
to use the DMA mapping API in a proper way. This patch fixes following DMA API
debug warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1241 check_sync+0x520/0x9f4
samsung-uart 12c20000.serial: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000006df0f580] [size=64 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00137-g07ca963 #51
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c0729058>] (check_sync+0x520/0x9f4)
[<c0729058>] (check_sync) from [<c072967c>] (debug_dma_sync_single_for_device+0x88/0xc8)
[<c072967c>] (debug_dma_sync_single_for_device) from [<c0803c10>] (s3c24xx_serial_start_tx_dma+0x100/0x2f8)
[<c0803c10>] (s3c24xx_serial_start_tx_dma) from [<c0804338>] (s3c24xx_serial_tx_chars+0x198/0x33c)
To mitigate some types of offline attacks, filesystem encryption is
designed to enforce that all files in an encrypted directory tree use
the same encryption policy (i.e. the same encryption context excluding
the nonce). However, the fscrypt_has_permitted_context() function which
enforces this relies on comparing struct fscrypt_info's, which are only
available when we have the encryption keys. This can cause two
incorrect behaviors:
1. If we have the parent directory's key but not the child's key, or
vice versa, then fscrypt_has_permitted_context() returned false,
causing applications to see EPERM or ENOKEY. This is incorrect if
the encryption contexts are in fact consistent. Although we'd
normally have either both keys or neither key in that case since the
master_key_descriptors would be the same, this is not guaranteed
because keys can be added or removed from keyrings at any time.
2. If we have neither the parent's key nor the child's key, then
fscrypt_has_permitted_context() returned true, causing applications
to see no error (or else an error for some other reason). This is
incorrect if the encryption contexts are in fact inconsistent, since
in that case we should deny access.
To fix this, retrieve and compare the fscrypt_contexts if we are unable
to set up both fscrypt_infos.
While this slightly hurts performance when accessing an encrypted
directory tree without the key, this isn't a case we really need to be
optimizing for; access *with* the key is much more important.
Furthermore, the performance hit is barely noticeable given that we are
already retrieving the fscrypt_context and doing two keyring searches in
fscrypt_get_encryption_info(). If we ever actually wanted to optimize
this case we might start by caching the fscrypt_contexts.
If device_add() fails, cleanup the cdev. Otherwise, we leak a kobj_map()
with a stale device number.
As Jason points out, there is a small possibility that userspace has
opened and mapped the device in the time between cdev_add() and the
device_add() failure. We need a new kill_dax_dev() helper to invalidate
any established mappings.
Fixes: ba09c01d2fa8 ("dax: convert to the cdev api") Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The author meant to free the variable that was just allocated, instead
of the one that failed to be allocated, but made a simple typo. This
patch rectifies that.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An open directory may have a NULL private_data pointer prior to readdir.
Fixes: 0de1f4c6f6c0 ("Add way to query server fs info for smb3") Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a real warning. Since the oplock is queued on the same
workqueue this can deadlock if there is only one worker thread active
for the workqueue (which will be the case during memory pressure when
the rescuer thread is handling it).
Furthermore, there is at least one other kind of hang possible due to
the oplock break handling if there is only worker. (This can be
reproduced without introducing memory pressure by having passing 1 for
the max_active parameter of cifsiod.) cifs_oplock_break() can wait
indefintely in the filemap_fdatawait() while the cifs_writev_complete()
work is blocked:
Showing all locks held in the system:
2 locks held by kworker/0:1/16:
#0: ("cifsiod"){.+.+.+}, at: process_one_work+0x255/0x8e0
#1: ((&cfile->oplock_break)){+.+.+.}, at: process_one_work+0x255/0x8e0
Fix these problems by creating a a new workqueue (with a rescuer) for
the oplock break work.
Signed-off-by: Rabin Vincent <rabinv@axis.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with 618763958b22, an open directory may have a NULL private_data
pointer prior to readdir. CIFS_ENUMERATE_SNAPSHOTS must check for this
before dereference.
Fixes: 834170c85978 ("Enable previous version support") Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The server may respond with success, and an output buffer less than
sizeof(struct smb_snapshot_array) in length. Do not leak the output
buffer in this case.
Fixes: 834170c85978 ("Enable previous version support") Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macs send the maximum buffer size in response on ioctl to validate
negotiate security information, which causes us to fail the mount
as the response buffer is larger than the expected response.
Changed ioctl response processing to allow for padding of validate
negotiate ioctl response and limit the maximum response size to
maximum buffer size.
Signed-off-by: Steve French <steve.french@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series aims to unify the setting and clearing of PF_MEMALLOC, which
prevents recursive reclaim. There are some places that clear the flag
unconditionally from current->flags, which may result in clearing a
pre-existing flag. This already resulted in a bug report that Patch 1
fixes (without the new helpers, to make backporting easier). Patch 2
introduces the new helpers, modelled after existing memalloc_noio_* and
memalloc_nofs_* helpers, and converts mm core to use them. Patches 3
and 4 convert non-mm code.
This patch (of 4):
__alloc_pages_direct_compact() sets PF_MEMALLOC to prevent deadlock
during page migration by lock_page() (see the comment in
__unmap_and_move()). Then it unconditionally clears the flag, which can
clear a pre-existing PF_MEMALLOC flag and result in recursive reclaim.
This was not a problem until commit a8161d1ed609 ("mm, page_alloc:
restructure direct compaction handling in slowpath"), because direct
compation was called only after direct reclaim, which was skipped when
PF_MEMALLOC flag was set.
Even now it's only a theoretical issue, as the new callsite of
__alloc_pages_direct_compact() is reached only for costly orders and
when gfp_pfmemalloc_allowed() is true, which means either
__GFP_NOMEMALLOC is in gfp_flags or in_interrupt() is true. There is no
such known context, but let's play it safe and make
__alloc_pages_direct_compact() robust for cases where PF_MEMALLOC is
already set.
Fixes: a8161d1ed609 ("mm, page_alloc: restructure direct compaction handling in slowpath") Link: http://lkml.kernel.org/r/20170405074700.29871-2-vbabka@suse.cz Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Chris Leech <cleech@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Josef Bacik <jbacik@fb.com> Cc: Lee Duncan <lduncan@suse.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Richard Weinberger <richard@nod.at> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getxattr uses vmalloc to allocate memory if kzalloc fails. This is
filled by vfs_getxattr and then copied to the userspace. vmalloc,
however, doesn't zero out the memory so if the specific implementation
of the xattr handler is sloppy we can theoretically expose a kernel
memory. There is no real sign this is really the case but let's make
sure this will not happen and use vzalloc instead.
fails because the second truncate did not happen if nothing had
requested the size after the write in echo. Thus i_size was zero (not
present) and the orangefs_setattr though i_size was zero and there was
nothing to do.
Signed-off-by: Martin Brandenburg <martin@omnibond.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the case of writing via mmap to a file with inline data is not
handled. This is maybe a rare case since it requires a writable memory
map of a very small file, but it is trivial to trigger with on
inline_data filesystem, and it causes the
'BUG_ON(ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA));' in
ext4_writepages() to be hit:
We could try to be smart and keep the inline data in this case, or at
least support delayed allocation when allocating the block, but these
solutions would be more complicated and don't seem worthwhile given how
rare this case seems to be. So just fix the bug by calling
ext4_convert_inline_data() when we're asked to make a page writable, so
that any inline data gets evicted, with the block allocated immediately.
Reported-by: Nick Alcock <nick.alcock@oracle.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address filtering with kernel symbols incorrectly resulted in the error
"Cannot determine size of symbol" because the no_size logic was the wrong
way around.
The driver progress routines can call cond_resched() when
a timeslice is exhausted and irqs are enabled.
If the ULP had been holding a spin lock without disabling irqs and
the post send directly called the progress routine, the cond_resched()
could yield allowing another thread from the same ULP to deadlock
on that same lock.
Correct by replacing the current hfi1_do_send() calldown with a unique
one for post send and adding an argument to hfi1_do_send() to indicate
that the send engine is running in a thread. If the routine is not
running in a thread, avoid calling cond_resched().
Fixes: Commit 831464ce4b74 ("IB/hfi1: Don't call cond_resched in atomic mode when sending packets") Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A warning message during SRIOV multicast cleanup should have actually been
a debug level message. The condition generating the warning does no harm
and can fill the message log.
In some cases, during testing, some tests were so intense as to swamp the
message log with these warning messages, causing a stall in the console
message log output task. This stall caused an NMI to be sent to all CPUs
(so that they all dumped their stacks into the message log).
Aside from the message flood causing an NMI, the tests all passed.
Once the message flood which caused the NMI is removed (by reducing the
warning message to debug level), the NMI no longer occurs.
Sample message log (console log) output illustrating the flood and
resultant NMI (snippets with comments and modified with ... instead
of hex digits, to satisfy checkpatch.pl):
In mlx4_ib_add, procedure mlx4_ib_alloc_eqs is called to allocate EQs.
However, in the mlx4_ib_add error flow, procedure mlx4_ib_free_eqs is not
called to free the allocated EQs.
Fixes: e605b743f33d ("IB/mlx4: Increase the number of vectors (EQs) available for ULPs") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When udev renames the netdev devices, ipoib debugfs entries does not
get renamed. As a result, if subsequent probe of ipoib device reuse the
name then creating a debugfs entry for the new device would fail.
Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part
of ipoib event handling in order to avoid any race condition between these.
Fixes: 1732b0ef3b3a ([IPoIB] add path record information in debugfs) Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com> Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel commit cited below restructured ib device management
so that the device kobject is initialized in ib_alloc_device.
As part of the restructuring, the kobject is now initialized in
procedure ib_alloc_device, and is later added to the device hierarchy
in the ib_register_device call stack, in procedure
ib_device_register_sysfs (which calls device_add).
However, in the ib_device_register_sysfs error flow, if an error
occurs following the call to device_add, the cleanup procedure
device_unregister is called. This call results in the device object
being deleted -- which results in various use-after-free crashes.
The correct cleanup call is device_del -- which undoes device_add
without deleting the device object.
The device object will then (correctly) be deleted in the
ib_register_device caller's error cleanup flow, when the caller invokes
ib_dealloc_device.
Fixes: 55aeed06544f6 ("IB/core: Make ib_alloc_device init the kobject") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch 327868212381 (make skb_copy_datagram_msg() et.al. preserve
->msg_iter on error) will revert the iov buffer if copy to iter
failed, but it didn't copy any datagram if the skb_checksum_complete
error, so no need to revert any data at this place.
v2: Sabrina notice that return -EFAULT when checksum error is not correct
here, it would confuse the caller about the return value, so fix it.
Fixes: 327868212381 ("make skb_copy_datagram_msg() et.al. preserve->msg_iter on error") Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the mmap_sem is contented then the vfio type1 IOMMU backend will
defer locked page accounting updates to a workqueue task. This has a
few problems and depending on which side the user tries to play, they
might be over-penalized for unmaps that haven't yet been accounted or
race the workqueue to enter more mappings than they're allowed. The
original intent of this workqueue mechanism seems to be focused on
reducing latency through the ioctl, but we cannot do so at the cost
of correctness. Remove this workqueue mechanism and update the
callers to allow for failure. We can also now recheck the limit under
write lock to make sure we don't exceed it.
vfio_pin_pages_remote() also now necessarily includes an unwind path
which we can jump to directly if the consecutive page pinning finds
that we're exceeding the user's memory limits. This avoids the
current lazy approach which does accounting and mapping up to the
fault, only to return an error on the next iteration to unwind the
entire vfio_dma.
Reviewed-by: Peter Xu <peterx@redhat.com> Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm-thin does not free the discard_parent bio after all chained sub
bios finished. The following kmemleak report could be observed after
pool with discard_passdown option processes discard bios in
linux v4.11-rc7. To fix this, we drop the discard_parent bio reference
when its endio (passdown_endio) called.
Signed-off-by: Dennis Yang <dennisyang@qnap.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When committing era metadata to disk, it doesn't always save the latest
spacemap metadata root in superblock. Due to this, metadata is getting
corrupted sometimes when reopening the device. The correct order of update
should be, pre-commit (shadows spacemap root), save the spacemap root
(newly shadowed block) to in-core superblock and then the final commit.
The CCP has the ability to perform several operations simultaneously,
but only one interrupt. When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.
This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.
Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CCP has the ability to perform several operations simultaneously,
but only one interrupt. When implemented as a PCI device and using
MSI-X/MSI interrupts, use a tasklet model to service interrupts. By
disabling and enabling interrupts from the CCP, coupled with the
queuing that tasklets provide, we can ensure that all events
(occurring on the device) are recognized and serviced.
This change fixes a problem wherein 2 or more busy queues can cause
notification bits to change state while a (CCP) interrupt is being
serviced, but after the queue state has been evaluated. This results
in the event being 'lost' and the queue hanging, waiting to be
serviced. Since the status bits are never fully de-asserted, the
CCP never generates another interrupt (all bits zero -> one or more
bits one), and no further CCP operations will be executed.
Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that we disable interrupts first when shutting down
the driver.
Signed-off-by: Gary R Hook <ghook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each CCP queue can product interrupts for 4 conditions:
operation complete, queue empty, error, and queue stopped.
This driver only works with completion and error events.
Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some cipher implementations will crash if you try to use them
without calling setkey first. This patch adds a check so that
the accept(2) call will fail with -ENOKEY if setkey hasn't been
done on the socket yet.
Fixes: 400c40cf78da ("crypto: algif - add AEAD support") Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When registering an integrity profile: if the template's interval_exp is
not 0 use it, otherwise use the ilog2() of logical block size of the
provided gendisk.
This fixes a long-standing DM linear target bug where it cannot pass
integrity data to the underlying device if its logical block size
conflicts with the underlying device's logical block size.
Reported-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our 32bit CP14/15 handling inherited some of the ARMv7 code for handling
the trapped system registers, completely missing the fact that the
fields for Rt and Rt2 are now 5 bit wide, and not 4...
Let's fix it, and provide an accessor for the most common Rt case.
Reviewed-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential races in kvm_psci_vcpu_on() by taking the kvm->lock
mutex. In general, it's a bad idea to allow more than one PSCI_CPU_ON
to process the same target VCPU at the same time. One such problem
that may arise is that one PSCI_CPU_ON could be resetting the target
vcpu, which fills the entire sys_regs array with a temporary value
including the MPIDR register, while another looks up the VCPU based
on the MPIDR value, resulting in no target VCPU found. Resolves both
races found with the kvm-unit-tests/arm/psci unit test.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Christoffer Dall <cdall@linaro.org> Reported-by: Levente Kurusa <lkurusa@redhat.com> Suggested-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Christoffer Dall <cdall@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we already entered/are about to enter SMM, don't allow switching to
INIT/SIPI_RECEIVED, otherwise the next call to kvm_apic_accept_events()
will report a warning.
Same applies if we are already in MP state INIT_RECEIVED and SMM is
requested to be turned on. Refuse to set the VCPU events in this case.
Fixes: cd7764fe9f73 ("KVM: x86: latch INITs while in system management mode") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David Hildenbrand <david@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is broken since ever but sadly nobody noticed.
Recent versions of GDB set DR_CONTROL unconditionally and
UML dies due to a heap corruption. It turns out that
the PTRACE_POKEUSER was copy&pasted from i386 and assumes
that addresses are 4 bytes long.
Fix that by using 8 as address size in the calculation.
Reported-by: jie cao <cj3054@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 11e63f6d920d added cache flushing for unaligned writes from an
iovec, covering the first and last cache line of a >= 8 byte write and
the first cache line of a < 8 byte write. But an unaligned write of
2-7 bytes can still cover two cache lines, so make sure we flush both
in that case.
Fixes: 11e63f6d920d ("x86, pmem: fix broken __copy_user_nocache ...") Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i386 glibc is buggy and calls the sigaction syscall incorrectly.
This is asymptomatic for normal programs, but it blows up on
programs that do evil things with segmentation. The ldt_gdt
self-test is an example of such an evil program.
This doesn't appear to be a regression -- I think I just got lucky
with the uninitialized memory that glibc threw at the kernel when I
wrote the test.
This hackish fix manually issues sigaction(2) syscalls to undo the
damage. Without the fix, ldt_gdt_32 segfaults; with the fix, it
passes for me.
The minimum size for a new stack (512 bytes) setup for arch/x86/boot components
when the bootloader does not setup/provide a stack for the early boot components
is not "enough".
The setup code executing as part of early kernel startup code, uses the stack
beyond 512 bytes and accidentally overwrites and corrupts part of the BSS
section. This is exposed mostly in the early video setup code, where
it was corrupting BSS variables like force_x, force_y, which in-turn affected
kernel parameters such as screen_info (screen_info.orig_video_cols) and
later caused an exception/panic in console_init().
Most recent boot loaders setup the stack for early boot components, so this
stack overwriting into BSS section issue has not been exposed.
Signed-off-by: Ashish Kalra <ashish@bluestacks.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170419152015.10011-1-ashishkalra@Ashishs-MacBook-Pro.local Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running a bind/unbind stress test with the dwc3 usb driver on rk3399,
the following crash was observed.
Unable to handle kernel NULL pointer dereference at virtual address 00000218
pgd = ffffffc00165f000
[00000218] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac
ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm
xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth
ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev
snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async
ppp_generic slhc tun
CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507
Hardware name: Google Kevin (DT)
Workqueue: pm pm_runtime_work
task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000
PC is at autosuspend_check+0x74/0x174
LR is at autosuspend_check+0x70/0x174
...
Call trace:
[<ffffffc00080dcc0>] autosuspend_check+0x74/0x174
[<ffffffc000810500>] usb_runtime_idle+0x20/0x40
[<ffffffc000785ae0>] __rpm_callback+0x48/0x7c
[<ffffffc000786af0>] rpm_idle+0x1e8/0x498
[<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Source:
(gdb) l *0xffffffc00080dcc0
0xffffffc00080dcc0 is in autosuspend_check
(drivers/usb/core/driver.c:1778).
1773 /* We don't need to check interfaces that are
1774 * disabled for runtime PM. Either they are unbound
1775 * or else their drivers don't support autosuspend
1776 * and so they are permanently active.
1777 */
1778 if (intf->dev.power.disable_depth)
1779 continue;
1780 if (atomic_read(&intf->dev.power.usage_count) > 0)
1781 return -EBUSY;
1782 w |= intf->needs_remote_wakeup;
Code analysis shows that intf is set to NULL in usb_disable_device() prior
to setting actconfig to NULL. At the same time, usb_runtime_idle() does not
lock the usb device, and neither does any of the functions in the
traceback. This means that there is no protection against a race condition
where usb_disable_device() is removing dev->actconfig->interface[] pointers
while those are being accessed from autosuspend_check().
To solve the problem, synchronize and validate device state between
autosuspend_check() and usb_disconnect().
kick_hub_wq() is called from hub_activate() even after failures to
communicate with the hub. This results in an endless sequence of
hub event -> hub activate -> wq trigger -> hub event -> ...
Provide two solutions for the problem.
- Only trigger the hub event queue if communication with the hub
is successful.
- After a suspend failure, only resume already suspended interfaces
if the communication with the device is still possible.
Each of the changes fixes the observed problem. Use both to improve
robustness.
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Felipe Balbi <balbi@kernel.org> Cc: Felix Fietkau <nbd@nbd.name> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: linux-snps-arc@lists.infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit bc49d1d17dcf ("usb: gadget: don't couple configfs to legacy
gadgets"),it is possible to build a modular kernel with both built-in
configfs support and modular legacy gadget drivers.
But when building a kernel without modules, it is also necessary to be
able to build with configfs but without any legacy gadget driver. This
was a possible configuration when the USB_CONFIGFS was a part of the
choice options, but not anymore.
Mark the choice for legacy gadget drivers as optional restores this.
The timer expiry routine `jr3_pci_poll_dev()` checks for expiry by
checking whether the absolute value of `jiffies` (stored in local
variable `now`) is greater than the expected expiry time in jiffy units.
This will fail when `jiffies` wraps around. Also, it seems to make
sense to handle the expiry one jiffy earlier than the current test. Use
`time_after_eq()` to check for expiry.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the driver does not consider allocation of the
subdevice private data to be a fatal error when attaching the COMEDI
device. It tests the subdevice private data pointer for validity at
certain points, but omits some crucial tests. In particular,
`jr3_pci_auto_attach()` calls `jr3_pci_alloc_spriv()` to allocate and
initialize the subdevice private data, but the same function
subsequently dereferences the pointer to access the `next_time_min` and
`next_time_max` members without checking it first. The other missing
test is in the timer expiry routine `jr3_pci_poll_dev()`, but it will
crash before it gets that far.
Fix the bug by returning `-ENOMEM` from `jr3_pci_auto_attach()` as soon
as one of the calls to `jr3_pci_alloc_spriv()` returns `NULL`. The
COMEDI core will subsequently call `jr3_pci_detach()` to clean up.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to deregister the USB driver before releasing the tty driver
to avoid use-after-free in the USB disconnect callback where the tty
devices are deregistered.
Fixes: 61e121047645 ("staging: gdm7240: adding LTE USB driver") Cc: Won Kang <wkang77@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 833415a3e781 ("cdc-wdm: fix "out-of-sync" due to
missing notifications")
There have been several reports of wdm_read returning unexpected EIO
errors with QMI devices using the qmi_wwan driver. The reporters
confirm that reverting prevents these errors. I have been unable to
reproduce the bug myself, and have no explanation to offer either. But
reverting is the safe choice here, given that the commit was an
attempt to work around a firmware problem. Living with a firmware
problem is still better than adding driver bugs.
Reported-by: Kasper Holtze <kasper@holtze.dk> Reported-by: Aleksander Morgado <aleksander@aleksander.es> Reported-by: Daniele Palmas <dnlplm@gmail.com> Fixes: 833415a3e781 ("cdc-wdm: fix "out-of-sync" due to missing notifications") Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class
To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().
As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.
This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.
Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per [1] issue #4,
"The periodic EP scheduler always tries to schedule the EPs
that have large intervals (interval equal to or greater than
128 microframes) into different microframes. So it maintains
an internal counter and increments for each large interval
EP added. When the counter is greater than 128, the scheduler
rejects the new EP. So when the hub re-enumerated 128 times,
it triggers this condition."
This results in Bandwidth error when devices with periodic
endpoints (ISO/INT) having bInterval > 7 are plugged and
unplugged several times on a TUSB73x0 XHCI host.
Workaround this issue by limiting the bInterval to 7
(i.e. interval to 6) for High-speed or faster periodic endpoints.
While testing modification of per se_node_acl queue_depth forcing
session reinstatement via lio_target_nacl_cmdsn_depth_store() ->
core_tpg_set_initiator_node_queue_depth(), a hung task bug triggered
when changing cmdsn_depth invoked session reinstatement while an iscsi
login was already waiting for session reinstatement to complete.
This can happen when an outstanding se_cmd descriptor is taking a
long time to complete, and session reinstatement from iscsi login
or cmdsn_depth change occurs concurrently.
To address this bug, explicitly set session_fall_back_to_erl0 = 1
when forcing session reinstatement, so session reinstatement is
not attempted if an active session is already being shutdown.
This patch has been tested with two scenarios. The first when
iscsi login is blocked waiting for iscsi session reinstatement
to complete followed by queue_depth change via configfs, and
second when queue_depth change via configfs us blocked followed
by a iscsi login driven session reinstatement.
Note this patch depends on commit d36ad77f702 to handle multiple
sessions per se_node_acl when changing cmdsn_depth, and for
pre v4.5 kernels will need to be included for stable as well.
Reported-by: Gary Guo <ghg@datera.io> Tested-by: Gary Guo <ghg@datera.io> Cc: Gary Guo <ghg@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log