The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Parallel reads from multiple threads on a file descriptor
are not well defined and racy. It is safer to return to original
behavior and simply fail the additional read.
The solution is to remove request for next read credit.
Fixes: ff1586a7ea57 ("mei: enqueue consecutive reads") Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the file system requires journal recovery, and the device is
read-ony, return EROFS to the mount system call. This allows xfstests
generic/050 to pass.
If the journal is aborted, the needs_recovery feature flag should not
be removed. Otherwise, it's the journal might not get replayed and
this could lead to more data getting lost.
In the case where the child's encryption context was inconsistent with
its parent directory, we were using inode->i_sb and inode->i_ino after
the inode had already been iput(). Fix this by doing the iput() in the
correct places.
ext4_journalled_write_end() did not propely handle all the cases when
generic_perform_write() did not copy all the data into the target page
and could mark buffers with uninitialized contents as uptodate and dirty
leading to possible data corruption (which would be quickly fixed by
generic_perform_write() retrying the write but still). Fix the problem
by carefully handling the case when the page that is written to is not
uptodate.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If filesystem groups are artifically small (using parameter -g to
mkfs.ext4), ext4_mb_normalize_request() can result in a request that is
larger than a block group. Trim the request size to not confuse
allocation code.
Reported-by: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because start block is not included in the range the hole appears at
the wrong offset (just after the desired offset) and the following
pwrite() overwrites already existent block, keeping hole untouched.
Simple way to verify wrong behaviour is to check zeroed blocks after
the test:
$ hexdump ./ext4.file | grep '0000 0000'
The root cause of the bug is a wrong range (start, stop], where start
should be inclusive, i.e. [start, stop].
This patch fixes the problem by including start into the range. But
not to break left shift (range collapse) stop points to the beginning
of the a block, not to the end.
The other not obvious change is an iterator check on validness in a
main loop. Because iterator is unsigned the following corner case
should be considered with care: insert a block at 0 offset, when stop
variables overflows and never becomes less than start, which is 0.
To handle this special case iterator is set to NULL to indicate that
end of the loop is reached.
loop_reread_partitions() needs to do I/O, but we just froze the queue,
so we end up waiting forever. This can easily be reproduced with losetup
-P. Fix it by moving the reread to after we unfreeze the queue.
Fixes: ecdd09597a57 ("block/loop: fix race between I/O and set_status") Reported-by: Tejun Heo <tj@kernel.org> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the journal has been aborted, we shouldn't mark the underlying
buffer head as dirty, since that will cause the metadata block to get
modified. And if the journal has been aborted, we shouldn't allow
this since it will almost certainly lead to a corrupted file system.
Userspace applications should be allowed to expect the membarrier system
call with MEMBARRIER_CMD_SHARED command to issue memory barriers on
nohz_full CPUs, but synchronize_sched() does not take those into
account.
Given that we do not want unrelated processes to be able to affect
real-time sensitive nohz_full CPUs, simply return ENOSYS when membarrier
is invoked on a kernel with enabled nohz_full CPUs.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> CC: Josh Triplett <josh@joshtriplett.org> CC: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Rik van Riel <riel@redhat.com> Acked-by: Lai Jiangshan <jiangshanlai@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device handler needs to check if a given queue belongs to a scsi
device; only then does it make sense to attach a device handler.
[mkp: dropped flags]
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb835223752 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family) Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: David Carroll <David.Carroll@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com> Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly set SRB flags when hosting device supports tagged queuing.
This patch improves the performance on Fiber Channel disks.
Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lvm2 sequence to manage dm-raid constructor flags that trigger a
rebuild or a reshape is defined as:
1) load table with flags (e.g. rebuild/delta_disks/data_offset)
2) clear out the flags in lvm2 metadata
3) store the lvm2 metadata, reload the table to reset the flags
previously established during the initial load (1) -- in order to
prevent repeatedly requesting a rebuild or a reshape on activation
Currently, loading an inactive table with rebuild/reshape flags
specified will cause dm-raid to rebuild/reshape on resume and thus start
updating the raid metadata (about the progress). When the second table
reload, to reset the flags, occurs the constructor accesses the volatile
progress state kept in the raid superblocks. Because the active mapping
is still processing the rebuild/reshape, that position will be stale by
the time the device is resumed.
In the reshape case, this causes data corruption by processing already
reshaped stripes again. In the rebuild case, it does _not_ cause data
corruption but instead involves superfluous rebuilds.
Fix by keeping the raid set frozen during the first resume and then
allow the rebuild/reshape during the second resume.
Fixes: 9dbd1aa3a ("dm raid: add reshaping support to the target") Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sloppy nature of lockless access to percpu pointers
(s->current_path) in rr_select_path(), from multiple threads, is
causing some paths to used more than others -- which results in less
IO performance being observed.
Revert these upstream commits to restore truly symmetric round-robin
IO submission in DM multipath:
b0b477c dm round robin: use percpu 'repeat_count' and 'current_path' 802934b dm round robin: do not use this_cpu_ptr() without having preemption disabled
There is no benefit to all this complexity if repeat_count = 1 (which is
the recommended default).
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rounding bug due to compiler generated temporary being 32bit was found
in remap_to_cache(). A localized cast in remap_to_cache() fixes the
corruption but this preferred fix (changing from uint32_t to sector_t)
eliminates potential for future rounding errors elsewhere.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, the trans_stat information of passive devfreq is not updated.
This patch updates the trans_stat information after setting the target
frequency of passive devfreq device.
The devfreq using passive governor is not able to change the governor.
So, the user can not change the governor through 'available_governor' sysfs
entry. Also, the devfreq which don't use the passive governor is not able to
change to 'passive' governor on the fly.
On failure to return a pathname from ima_d_path(), a pointer to
dname is returned, which is subsequently used in the IMA measurement
list, the IMA audit records, and other audit logging. Saving the
pointer to dname for later use has the potential to race with rename.
Intead of returning a pointer to dname on failure, this patch returns
a pointer to a copy of the filename.
The problem is that shmat() calls do_mmap_pgoff() with MAP_FIXED, and
the address rounded down to 0. For the regular mmap case, the
protection mentioned above is that the kernel gets to generate the
address -- arch_get_unmapped_area() will always check for MAP_FIXED and
return that address. So by the time we do security_mmap_addr(0) things
get funky for shmat().
The testcase itself shows that while a regular user crashes, root will
not have a problem attaching a nil-page. There are two possible fixes
to this. The first, and which this patch does, is to simply allow root
to crash as well -- this is also regular mmap behavior, ie when hacking
up the testcase and adding mmap(... |MAP_FIXED). While this approach
is the safer option, the second alternative is to ignore SHM_RND if the
rounded address is 0, thus only having MAP_SHARED flags. This makes the
behavior of shmat() identical to the mmap() case. The downside of this
is obviously user visible, but does make sense in that it maintains
semantics after the round-down wrt 0 address and mmap.
Currently SS_AUTODISARM is not supported in compatibility mode, but does
not return -EINVAL either. This makes dosemu built with -m32 on x86_64
to crash. Also the kernel's sigaltstack selftest fails if compiled with
-m32.
This patch adds the needed support.
Link: http://lkml.kernel.org/r/20170205101213.8163-2-stsp@list.ru Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net> Cc: Milosz Tanski <milosz@adfin.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Waiman Long <Waiman.Long@hpe.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dmitry Safonov <dsafonov@virtuozzo.com> Cc: Wang Xiaoqiang <wangxq10@lzu.edu.cn> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_scan_count() considers the whole node LRU size when
- doing SCAN_FILE due to many page cache inactive pages
- calculating the number of pages to scan
In both cases this might lead to unexpected behavior especially on 32b
systems where we can expect lowmem memory pressure very often.
A large highmem zone can easily distort SCAN_FILE heuristic because
there might be only few file pages from the eligible zones on the node
lru and we would still enforce file lru scanning which can lead to
trashing while we could still scan anonymous pages.
The later use of lruvec_lru_size can be problematic as well. Especially
when there are not many pages from the eligible zones. We would have to
skip over many pages to find anything to reclaim but shrink_node_memcg
would only reduce the remaining number to scan by SWAP_CLUSTER_MAX at
maximum. Therefore we can end up going over a large LRU many times
without actually having chance to reclaim much if anything at all. The
closer we are out of memory on lowmem zone the worse the problem will
be.
Fix this by filtering out all the ineligible zones when calculating the
lru size for both paths and consider only sc->reclaim_idx zones.
The patch would need to be tweaked a bit to apply to 4.10 and older but
I will do that as soon as it hits the Linus tree in the next merge
window.
Link: http://lkml.kernel.org/r/20170117103702.28542-3-mhocko@kernel.org Fixes: b2e18757f2c9 ("mm, vmscan: begin reclaiming pages on a per-node basis") Signed-off-by: Michal Hocko <mhocko@suse.com> Tested-by: Trevor Cordes <trevor@tecnopolis.ca> Acked-by: Minchan Kim <minchan@kernel.org> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lruvec_lru_size returns the full size of the LRU list while we sometimes
need a value reduced only to eligible zones (e.g. for lowmem requests).
inactive_list_is_low is one such user. Later patches will add more of
them. Add a new parameter to lruvec_lru_size and allow it filter out
zones which are not eligible for the given context.
Link: http://lkml.kernel.org/r/20170117103702.28542-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by: Minchan Kim <minchan@kernel.org> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_BALLOON_COMPACTION=y the kernel will mount balloon_mnt for
balloon page migration when we probe a virtio_balloon device. However
we do not unmount it when removing the device. Fix this.
Fixes: b1123ea6d3b3 ("mm: balloon: use general non-lru movable page feature") Link: http://lkml.kernel.org/r/1486531318-35189-1-git-send-email-xieyisheng1@huawei.com Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Rafael Aquini <aquini@redhat.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Gioh Kim <gi-oh.kim@profitbricks.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Xishi Qiu <qiuxishi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With rw_page, page_endio is used for completing IO on a page and it
propagates write error to the address space if the IO fails. The
problem is it accesses page->mapping directly which might be okay for
file-backed pages but it shouldn't for anonymous page. Otherwise, it
can corrupt one of field from anon_vma under us and system goes panic
randomly.
swap_writepage
bdev_writepage
ops->rw_page
I encountered the BUG during developing new zram feature and it was
really hard to figure it out because it made random crash, somtime
mmap_sem lockdep, sometime other places where places never related to
zram/zsmalloc, and not reproducible with some configuration.
When I consider how that bug is subtle and people do fast-swap test with
brd, it's worth to add stable mark, I think.
Fixes: dd6bd0d9c7db ("swap: use bdev_read_page() / bdev_write_page()") Signed-off-by: Minchan Kim <minchan@kernel.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of a window period, if the reclaimed pages is greater than
scanned, an unsigned underflow can result in a huge pressure value and
thus a critical event. Reclaimed pages is found to go higher than
scanned because of the addition of reclaimed slab pages to reclaimed in
shrink_node without a corresponding increment to scanned pages.
Minchan Kim mentioned that this can also happen in the case of a THP
page where the scanned is 1 and reclaimed could be 512.
Link: http://lkml.kernel.org/r/1486641577-11685-1-git-send-email-vinmenon@codeaurora.org Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org> Acked-by: Minchan Kim <minchan@kernel.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Rik van Riel <riel@redhat.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Anton Vorontsov <anton.vorontsov@linaro.org> Cc: Shiraz Hashim <shashim@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When @node_reclaim_node isn't 0, the page allocator tries to reclaim
pages if the amount of free memory in the zones are below the low
watermark. On Power platform, none of NUMA nodes are scanned for page
reclaim because no nodes match the condition in zone_allows_reclaim().
On Power platform, RECLAIM_DISTANCE is set to 10 which is the distance
of Node-A to Node-A. So the preferred node even won't be scanned for
page reclaim.
size <<= 30;
p = malloc(size);
assert(p);
memset(p, 0, size);
end = time(NULL);
printf("Used time: %ld seconds\n", end - start);
sleep(3600);
return 0;
}
The system I use for testing has two NUMA nodes. Both have 128GB
memory. In below scnario, the page caches on node#0 should be reclaimed
when it encounters pressure to accommodate request of allocation.
The mem_hotplug_{begin,done} lock coordinates with {get,put}_online_mems()
to hold off "readers" of the current state of memory from new hotplug
actions. mem_hotplug_begin() expects exclusive access, via the
device_hotplug lock, to set mem_hotplug.active_writer. Calling
mem_hotplug_begin() without locking device_hotplug can lead to
corrupting mem_hotplug.refcount and missed wakeups / soft lockups.
Currently we call copy_page_to_iter() for uncached reading into a pipe.
This is wrong because it treats pages as VFS cache pages and copies references
rather than actual data. When we are trying to read from the pipe we end up
calling page_cache_pipe_buf_confirm() which returns -ENODATA. This error
is translated into 0 which is returned to a user.
This issue is reproduced by running xfs-tests suite (generic test #249)
against mount points with "cache=none". Fix it by mapping pages manually
and calling copy_to_iter() that copies data into the pipe.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the macros are incorrect with wrong bit-shifts resulting in picking
the incorrect invalidation granularity. Incorrect Source-ID in extended
devtlb invalidation caused device side errors.
It is allowed to call regulator_get with a NULL dev argument
(_regulator_get explicitly checks for it) but this causes an error later
when printing /sys/kernel/debug/regulator_summary.
Fix this by explicitly handling "deviceless" consumers in the debugfs code.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm is automatically enabled when an application sets the policy
via ->link() call back by using coresight_enable(), which keeps the
refcount of the current users of the STM. However, the unlink() callback
issues stm_disable() directly, which leaves the STM turned off, without
the coresight layer knowing about it. This prevents any further uses
of the STM hardware as the coresight layer still thinks the STM is
turned on and doesn't enable the hardware when required. Even manually
enabling the STM via sysfs can't really enable the hw.
e.g,
$ echo 1 > $CS_DEVS/$ETR/enable_sink
$ mkdir -p $CONFIG_FS/stp-policy/$source.0/stm_test/
$ echo 32768 65535 > $CONFIG_FS/stp-policy/$source.0/stm_test/channels
$ echo 64 > $CS_DEVS/$source/traceid
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffffa95fa000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.1
597+1 records in
597+1 records out
305920 bytes (306 kB) copied, 0.399952 s, 765 kB/s
$ ./stm_app
Sending 64000 byte blocks of pattern 0 at 0us intervals
Success to map channel(32768~32783) to 0xffff7e9e2000
Sending on channel 32768
$ dd if=/dev/$ETR of=~/trace.bin.2
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.0232083 s, 0.0 kB/s
Note that we don't get any data from the ETR for the second session.
Also dmesg shows :
[ 77.520458] coresight-tmc 20800000.etr: TMC-ETR enabled
[ 77.537097] coresight-replicator etr_replicator@20890000: REPLICATOR enabled
[ 77.558828] coresight-replicator main_replicator@208a0000: REPLICATOR enabled
[ 77.581068] coresight-funnel 208c0000.main_funnel: FUNNEL inport 0 enabled
[ 77.602217] coresight-tmc 20840000.etf: TMC-ETF enabled
[ 77.618422] coresight-stm 20860000.stm: STM tracing enabled
[ 139.554252] coresight-stm 20860000.stm: STM tracing disabled
# End of first tracing session
[ 146.351135] coresight-tmc 20800000.etr: TMC read start
[ 146.514486] coresight-tmc 20800000.etr: TMC read end
# Note that the STM is not turned on via stm_generic_link()->coresight_enable()
# and hence none of the components are turned on.
[ 152.479080] coresight-tmc 20800000.etr: TMC read start
[ 152.542632] coresight-tmc 20800000.etr: TMC read end
This patch fixes the problem by balancing the unlink operation by using
the coresight_disable(), keeping the coresight layer in sync with the
hardware state and thus allowing normal usage of the STM component.
gcc-7 detects that wlanhdr_to_ethhdr() in two drivers calls memcpy() with
a destination argument that an earlier function call may have set to NULL:
staging/rtl8188eu/core/rtw_recv.c: In function 'wlanhdr_to_ethhdr':
staging/rtl8188eu/core/rtw_recv.c:1318:2: warning: argument 1 null where non-null expected [-Wnonnull]
staging/rtl8712/rtl871x_recv.c: In function 'r8712_wlanhdr_to_ethhdr':
staging/rtl8712/rtl871x_recv.c:649:2: warning: argument 1 null where non-null expected [-Wnonnull]
I'm fixing this by adding a NULL pointer check and returning failure
from the function, which is hopefully already handled properly.
This seems to date back to when the drivers were originally added,
so backporting the fix to stable seems appropriate. There are other
related realtek drivers in the kernel, but none of them contain a
function with a similar name or produce this warning.
Fixes: 1cc18a22b96b ("staging: r8188eu: Add files for new driver - part 5") Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loopback driver allows the user to set a minimum delay of up to one
second to be inserted between test iterations (i.e. request
submissions). The delay is currently specified in microseconds and is
implemented using udelay.
Busy looping for long periods is not just anti-social; udelay must not
be used for delays longer than a few milliseconds due to the risk of
integer overflow.
Replace the broken udelay with a usleep_range with a 100 us range for
short delays (< 20 ms) and otherwise revert to using msleep.
Fixes: b36f04fa9417 ("greybus: loopback: Convert thread delay to microseconds") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
The sequencer FIFO management has a bug that may lead to a corruption
(shortage) of the cell linked list. When a sequencer client faces an
error at the event delivery, it tries to put back the dequeued cell.
When the first queue was put back, this forgot the tail pointer
tracking, and the link will be screwed up.
Although there is no memory corruption, the sequencer client may stall
forever at exit while flushing the pending FIFO cells in
snd_seq_pool_done(), as spotted by syzkaller.
This patch addresses the missing tail pointer tracking at
snd_seq_fifo_cell_putback(). Also the patch makes sure to clear the
cell->enxt pointer at snd_seq_fifo_event_in() for avoiding a similar
mess-up of the FIFO linked list.
Currently ctxfi driver tries to set only the 64bit DMA mask on 64bit
architectures, and bails out if it fails. This causes a problem on
some platforms since the 64bit DMA isn't always guaranteed. We should
fall back to the default 32bit DMA when 64bit DMA fails.
When a user sets a too small ticks with a fine-grained timer like
hrtimer, the kernel tries to fire up the timer irq too frequently.
This may lead to the condensed locks, eventually the kernel spinlock
lockup with warnings.
For avoiding such a situation, we define a lower limit of the
resolution, namely 1ms. When the user passes a too small tick value
that results in less than that, the kernel returns -EINVAL now.
Like for Sunrise Point, the total stream number of Lewisburg's
input and output stream exceeds 15 (GCAP is 0x9701), which will
cause some streams do not work because of the overflow on
SDxCTL.STRM field if using the legacy stream tag allocation method.
The issue is the same as "dd9aa335c880 ALSA: hda/realtek - Can't adjust
speaker's volume on a Dell AIO", the output requires to connect to a node
with Amp-out capability.
Applying the same fixup "ALC298_FIXUP_SPK_VOLUME" can fix the issue.
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Commit a92e7c3d82a1 ("spi: s3c64xx: consider the case when the CS
line is not connected") introduced an inconsistency between the
binding, where the disconnected CS line was marked as
'no-cs-readback', and the driver.
The driver is erroneously checking for that attribute with
property name of 'broken-cs'.
Check for 'no-cs-readback' in the driver as well.
Fixes: a92e7c3d82a1 ("spi: s3c64xx: consider the case when the CS line is not connected") Signed-off-by: Andi Shyti <andi.shyti@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xattr_sem deadlock problems fixed in commit 2e81a4eeedca: "ext4:
avoid deadlock when expanding inode size" didn't include the use of
xattr_sem in fs/ext4/inline.c. With the addition of project quota
which added a new extra inode field, this exposed deadlocks in the
inline_data code similar to the ones fixed by 2e81a4eeedca.
When the functions replaced media entity types, the range which was
allowed for the types was incorrect. This meant that media entity types
for specific devices were not passed correctly to the userspace through
MEDIA_IOC_ENUM_ENTITIES. Fix it.
Fixes: commit b2cd27448b33 ("[media] media-device: map new functions into old types for legacy API") Reported-and-tested-by: Antti Laakso <antti.laakso@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting GPIOs during probe causes null pointer deference when
GPIOLIB was not selected by Kconfig. Initialize driver private
field before calling set gpios.
With commit 67bf5156edc4 ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.
This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.
is_jump_ins() checks for plain jump ("j") instructions since commit e7438c4b893e ("MIPS: Fix sibling call handling in get_frame_info") but
that commit didn't make the same change to the microMIPS code, leaving
it inconsistent with the MIPS32/MIPS64 code. Handle the microMIPS
encoding of the jump instruction too such that it behaves consistently.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: e7438c4b893e ("MIPS: Fix sibling call handling in get_frame_info") Cc: Tony Wu <tung7970@gmail.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14533/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_frame_info() calculates the offset of the return address within a
stack frame simply by dividing a the bottom 16 bits of the instruction,
treated as a signed integer, by the size of a long. Whilst this works
for MIPS32 & MIPS64 ISAs where the sw or sd instructions are used, it's
incorrect for microMIPS where encodings differ. The result is that we
typically completely fail to unwind the stack on microMIPS.
Fix this by adjusting is_ra_save_ins() to calculate the return address
offset, and take into account the various different encodings there in
the same place as we consider whether an instruction is storing the
ra/$31 register.
With this we are now able to unwind the stack for kernels targetting the
microMIPS ISA, for example we can produce:
is_jump_ins() checks 16b instruction fields without verifying that the
instruction is indeed 16b, as is done by is_ra_save_ins() &
is_sp_move_ins(). Add the appropriate check.
get_frame_info() is meant to iterate over up to the first 128
instructions within a function, but for microMIPS kernels it will not
reach that many instructions unless the function is 512 bytes long since
we calculate the maximum number of instructions to check by dividing the
function length by the 4 byte size of a union mips_instruction. In
microMIPS kernels this won't do since instructions are variable length.
Fix this by instead checking whether the pointer to the current
instruction has reached the end of the function, and use max_insns as a
simple constant to check the number of iterations against.
During stack unwinding we call a number of functions to determine what
type of instruction we're looking at. The union mips_instruction pointer
provided to them may be pointing at a 2 byte, but not 4 byte, aligned
address & we thus cannot directly access the 4 byte wide members of the
union mips_instruction. To avoid this is_ra_save_ins() copies the
required half-words of the microMIPS instruction to a correctly aligned
union mips_instruction on the stack, which it can then access safely.
The is_jump_ins() & is_sp_move_ins() functions do not correctly perform
this temporary copy, and instead attempt to directly dereference 4 byte
fields which may be misaligned and lead to an address exception.
Fix this by copying the instruction halfwords to a temporary union
mips_instruction in get_frame_info() such that we can provide a 4 byte
aligned union mips_instruction to the is_*_ins() functions and they do
not need to deal with misalignment themselves.
get_frame_info() can be called in microMIPS kernels with the ISA bit
already clear. For example this happens when unwind_stack_by_address()
is called because we begin with a PC that has the ISA bit set & subtract
the (odd) offset from the preceding symbol (which does not have the ISA
bit set). Since get_frame_info() unconditionally subtracts 1 from the PC
in microMIPS kernels it incorrectly misaligns the address it then
attempts to access code at, leading to an address error exception.
Fix this by using msk_isa16_mode() to clear the ISA bit, which allows
get_frame_info() to function regardless of whether it is provided with a
PC that has the ISA bit set or not.
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Fixes: 95135bfa7ead ("MIPS: Lantiq: Deactivate most of the devices by default") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: John Crispin <john@phrozen.org> Cc: hauke.mehrtens@lantiq.com Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15078/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If copy_from_user is called with a large buffer (>= 128 bytes) and the
userspace buffer refers partially to unreadable memory, then it is
possible for Octeon's copy_from_user to report the wrong number of bytes
have been copied. In the case where the buffer size is an exact multiple
of 128 and the fault occurs in the last 64 bytes, copy_from_user will
report that all the bytes were copied successfully but leave some
garbage in the destination buffer.
The bug is in the main __copy_user_common loop in octeon-memcpy.S where
in the middle of the loop, src and dst are incremented by 128 bytes. The
l_exc_copy fault handler is used after this but that assumes that
"src < THREAD_BUADDR($28)". This is not the case if src has already been
incremented.
Fix by adding an extra fault handler which rewinds the src and dst
pointers 128 bytes before falling though to l_exc_copy.
Thanks to the pwritev test from the strace test suite for originally
highlighting this bug!
Fixes: 5b3b16880f40 ("MIPS: Add Cavium OCTEON processor support ...") Signed-off-by: James Cowgill <James.Cowgill@imgtec.com> Acked-by: David Daney <david.daney@cavium.com> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14978/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For certain arguments such as saddr = 0xc0a8fd60, daddr = 0xc0a8fda1,
len = 80, proto = 17, sum = 0x7eae049d there will be a carry when
folding the intermediate 64 bit checksum to 32 bit but the code doesn't
add the carry back to the one's complement sum, thus an incorrect result
will be generated.
Reported-by: Mark Zhang <bomb.zhang@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early clock API pic32_get_pbclk() is defined in early_clk.c and used by
time.c and early_console.c. When CONFIG_EARLY_PRINTK isn't set,
early_clk.c isn't compiled and time.c fails to link.
Fix it by compiling early_clk.c always. Also sort files in alphabetical
order.
The buffered write failure handling code in
xfs_file_iomap_end_delalloc() has a couple minor problems. First, if
written == 0, start_fsb is not rounded down and it fails to kill off a
delalloc block if the start offset is block unaligned. This results in a
lingering delalloc block and broken delalloc block accounting detected
at unmount time. Fix this by rounding down start_fsb in the unlikely
event that written == 0.
Second, it is possible for a failed overwrite of a delalloc extent to
leave dirty pagecache around over a hole in the file. This is because is
possible to hit ->iomap_end() on write failure before the iomap code has
attempted to allocate pagecache, and thus has no need to clean it up. If
the targeted delalloc extent was successfully written by a previous
write, however, then it does still have dirty pages when ->iomap_end()
punches out the underlying blocks. This ultimately results in writeback
over a hole. To fix this problem, unconditionally punch out the
pagecache from XFS before the associated delalloc range.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function rtl_usb_start we pre-allocate a certain number of urbs
for RX path but they will not be freed when calling rtl_usb_stop. This
results in leaking urbs when doing ifconfig up and down. Eventually,
the system has no available urbs.
Signed-off-by: Michael Schenk <michael.schenk@albis-elcon.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When !CONFIG_CGROUP_WRITEBACK, bdi has single bdi_writeback_congested
at bdi->wb_congested. cgwb_bdi_init() allocates it with kzalloc() and
doesn't do further initialization. This usually works fine as the
reference count gets bumped to 1 by wb_init() and the put from
wb_exit() releases it.
However, when wb_init() fails, it puts the wb base ref automatically
freeing the wb and the explicit kfree() in cgwb_bdi_init() error path
ends up trying to free the same pointer the second time causing a
double-free.
Fix it by explicitly initilizing the refcnt to 1 and putting the base
ref from cgwb_bdi_destroy().
But breaks one thing due to the following old issue:
Buidling Linux kernel with Intel compiler originally depends on acgcc.h
not acintel.h.
So after making Intel compiler build working in ACPICA upstream by
correctly using acintel.h, it becomes unable to build Linux kernel using
Intel compiler as there is no acintel.h in the kernel source tree.
This patch releases acintel.h to Linux kernel and fixes its inclusion in
acenv.h.
Fixes: 9fa1cebdbfff (ACPICA: OSL: Cleanup the inclusion order of the compiler-specific headers) Link: https://github.com/acpica/acpica/commit/b59347d0 Tested-by: Stepan M Mishura <stepan.m.mishura@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3bb398d925 ("netfilter: nf_ct_helper: disable automatic helper
assignment") is causing behavior regressions in firewalls, as traffic
handled by conntrack helpers is now by default not passed through even
though it was before due to missing CT targets (which were not necessary
before this commit).
The default had to be switched off due to security reasons [1] [2] and
therefore should stay the way it is, but let's be friendly to firewall
admins and issue a warning the first time we're in situation where packet
would be likely passed through with the old default but we're likely going
to drop it on the floor now.
Rewrite the code a little bit as suggested by Linus, so that we avoid
spaghettiing the code even more -- namely the whole decision making
process regarding helper selection (either automatic or not) is being
separated, so that the whole logic can be simplified and code (condition)
duplication reduced.
The goldfish platform code registers the platform device unconditionally
which causes havoc in several ways if the goldfish_pdev_bus driver is
enabled:
- Access to the hardcoded physical memory region, which is either not
available or contains stuff which is completely unrelated.
- Prevents that the interrupt of the serial port can be requested
- In case of a spurious interrupt it goes into a infinite loop in the
interrupt handler of the pdev_bus driver (which needs to be fixed
seperately).
Add a 'goldfish' command line option to make the registration opt-in when
the platform is compiled in.
I'm seriously grumpy about this engineering trainwreck, which has seven
SOBs from Intel developers for 50 lines of code. And none of them figured
out that this is broken. Impressive fail!
Fixes: ddd70cf93d78 ("goldfish: platform device for x86") Reported-by: Gabriel C <nix.or.die@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4a510969374a ("tty: Make tty_files_lock per-tty") a new
tty_struct spin lock is taken in the tty release path, but the
USB-serial-console hack was never updated hence leaving the lock of its
"fake" tty uninitialised. This was eventually detected by lockdep.
Make sure to initialise the new lock also for the fake tty to address
this regression.
Yes, this code is a mess, but cleaning it up is left for another day.
Fixes: 4a510969374a ("tty: Make tty_files_lock per-tty") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation failed to detect short transfers, something
which could lead to bits of the uninitialised heap transfer buffer
leaking to user space.
Fixes: 149fc791a452 ("USB: ark3116: Setup some basic infrastructure for new ark3116 driver.") Fixes: f4c1e8d597d1 ("USB: ark3116: Make existing functions 16450-aware and add close and release functions.") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opticon driver used a control request at open to trigger a CTS
status notification to be sent over the bulk-in pipe. When the driver
was converted to using the generic read implementation, an inverted test
prevented this request from being sent, something which could lead to
TIOCMGET reporting an incorrect CTS state.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 7a6ee2b02751 ("USB: opticon: switch to generic read implementation") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to detect short control transfers and return zero on success
when retrieving the modem status.
This fixes the TIOCMGET implementation which since e1ed212d8593 ("USB:
spcp8x5: add proper modem-status support") has returned TIOCM_LE on
successful retrieval, and avoids leaking bits from the stack on short
transfers.
This also fixes the carrier-detect implementation which since the above
mentioned commit unconditionally has returned true.
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc> Fixes: 72fda3ca6fc1 ("USB: serial: ftd_sio: implement sysrq handling on
break") Fixes: 166ceb690750 ("USB: ftdi_sio: clean up line-status handling") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6ba ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <a.aubert@overkiz.com> Fixes: 557aaa7ffab6 ("ft232: support the ASYNC_LOW_LATENCY flag") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to detect short responses when fetching the modem status in
order to avoid parsing uninitialised buffer data and having bits of it
leak to user space.
Note that we still allow for short 1-byte responses.
Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design
change.
Signed-off-by: Ken Lin <yungching0725@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
$
Commit 34b88a68f26a ("net: Fix use after free in the recvmmsg exit path"),
changed the exit path of recvmmsg to always return the datagrams
variable and modified the error paths to set the variable to the error
code returned by recvmsg if necessary.
However in the case sock_error returned an error, the error code was
then ignored, and recvmmsg returned 0.
Change the error path of recvmmsg to correctly return the error code
of sock_error.
The bug was triggered by using recvmmsg on a CAN interface which was
not up. Linux 4.6 and later return 0 in this case while earlier
releases returned -ENETDOWN.
Fixes: 34b88a68f26a ("net: Fix use after free in the recvmmsg exit path") Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The skbs processed by ip_cmsg_recv() are not guaranteed to
be linear e.g. when sending UDP packets over loopback with
MSGMORE.
Using csum_partial() on [potentially] the whole skb len
is dangerous; instead be on the safe side and use skb_checksum().
Thanks to syzkaller team to detect the issue and provide the
reproducer.
v1 -> v2:
- move the variable declaration in a tighter scope
Fixes: ad6f939ab193 ("ip: Add offset parameter to ip_cmsg_recv") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>