Eric Dumazet [Wed, 13 Sep 2023 12:58:35 +0000 (12:58 +0000)]
net: use indirect call helpers for sk->sk_prot->release_cb()
When adding sk->sk_prot->release_cb() call from __sk_flush_backlog()
Paolo suggested using indirect call helpers to take care of
CONFIG_RETPOLINE=y case.
It turns out Google had such mitigation for years in release_sock(),
it is time to make this public :)
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Sep 2023 12:54:34 +0000 (13:54 +0100)]
Merge branch 'icssg-half-duplex-support'
====================
net: Add Half Duplex support for ICSSG Driver
This series adds support for half duplex operation for ICSSG driver.
In order to support half-duplex operation at 10M and 100M link speeds, the
PHY collision detection signal (COL) should be routed to ICSSG GPIO pin
(PRGx_PRU0/1_GPI10) so that firmware can detect collision signal and apply
the CSMA/CD algorithm applicable for half duplex operation. A DT property,
"ti,half-duplex-capable" is introduced for this purpose in the first patch
of the series. If board has PHY COL pin conencted to PRGx_PRU1_GPIO10,
this DT property can be added to eth node of ICSSG, MII port to support
half duplex operation at that port.
Second patch of the series configures driver to support half-duplex
operation if the DT property "ti,half-duplex-capable" is enabled.
This series addresses comments on [v2]. This series is based on the latest
net-next/main. This series has no dependency.
Changes from v1 to v2:
*) Changed the description of "ti,half-duplex-capable" property as asked
by Rob and Andrew to avoid confusion between capable and enable.
Changes from v1 to v2:
*) Dropped the RFC tag.
*) Added RB tags of Andrew and Roger.
net: ti: icssg-prueth: Add support for half duplex operation
This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a random number, in DMEM HD_RAND_SEED_OFFSET
field, which will be used by firmware for Back off time calculation.
- Driver informs FW about half duplex link operation in DMEM
PORT_LINK_SPEED_OFFSET field by setting bit 7 for 10/100M HD.
Hence, the half duplex operation depends on board design the
"ti,half-duplex-capable" property has to be enabled for ICSS-G ports if HW
is capable to perform half duplex.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: Add documentation for Half duplex support.
In order to support half-duplex operation at 10M and 100M link speeds, the
PHY collision detection signal (COL) should be routed to ICSSG
GPIO pin (PRGx_PRU0/1_GPI10) so that firmware can detect collision signal
and apply the CSMA/CD algorithm applicable for half duplex operation. A DT
property, "ti,half-duplex-capable" is introduced for this purpose. If
board has PHY COL pin conencted to PRGx_PRU1_GPIO10, this DT property can
be added to eth node of ICSSG, MII port to support half duplex operation at
that port.
Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Conor Dooley <conor.dooley@microchip.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: rtl8366rb: Implement setting up link on CPU port
We auto-negotiate most ports in the RTL8366RB driver, but
the CPU port is hard-coded to 1Gbit, full duplex, tx and
rx pause.
This isn't very nice. People may configure speed and
duplex differently in the device tree.
Actually respect the arguments passed to the function for
the CPU port, which get passed properly after Russell's
patch "net: dsa: realtek: add phylink_get_caps implementation"
After this the link is still set up properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PTP block supports generating PPS output signal on GPIO pin. This patch
adds the support in the PTP PHC driver using standard periodic output
interface.
User can enable/disable/configure PPS by writing to the below sysfs entry
Example to generate 50% duty cycle PPS signal:
echo 0 0 0 0 500000000 > /sys/class/ptp/ptp0/period
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Sai Krishna <saikrishnag@marvell.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Sep 2023 09:33:49 +0000 (10:33 +0100)]
Merge branch 'ipv6-data-races'
Eric Dumazet says:
====================
ipv6: round of data-races fixes
This series is inspired by one related syzbot report.
Many inet6_sk(sk) fields reads or writes are racy.
Move 1-bit fields to inet->inet_flags to provide
atomic safety. inet6_{test|set|clear|assign}_bit() helpers
could be changed later if we need to make room in inet_flags.
Also add missing READ_ONCE()/WRITE_ONCE() when
lockless readers need access to specific fields.
np->srcprefs will be handled separately to avoid merge conflicts
because a prior patch was posted for net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'net-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Quite unusually, this does not contains any fix coming from subtrees
(nf, ebpf, wifi, etc).
Current release - regressions:
- bcmasp: fix possible OOB write in bcmasp_netfilt_get_all_active()
Previous releases - regressions:
- ipv4: fix one memleak in __inet_del_ifa()
- tcp: fix bind() regressions for v4-mapped-v6 addresses.
- tls: do not free tls_rec on async operation in
bpf_exec_tx_verdict()
- dsa: fixes for SJA1105 FDB regressions
- veth: update XDP feature set when bringing up device
- igb: fix hangup when enabling SR-IOV
Previous releases - always broken:
- kcm: fix memory leak in error path of kcm_sendmsg()
- smc: fix data corruption in smcr_port_add
- microchip: fix possible memory leak for vcap_dup_rule()"
* tag 'net-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
net: renesas: rswitch: Add spin lock protection for irq {un}mask
net: renesas: rswitch: Fix unmasking irq condition
igb: clean up in all error paths when enabling SR-IOV
ixgbe: fix timestamp configuration code
selftest: tcp: Add v4-mapped-v6 cases in bind_wildcard.c.
selftest: tcp: Move expected_errno into each test case in bind_wildcard.c.
selftest: tcp: Fix address length in bind_wildcard.c.
tcp: Fix bind() regression for v4-mapped-v6 non-wildcard address.
tcp: Fix bind() regression for v4-mapped-v6 wildcard address.
tcp: Factorise sk_family-independent comparison in inet_bind2_bucket_match(_addr_any).
ipv6: fix ip6_sock_set_addr_preferences() typo
veth: Update XDP feature set when bringing up device
net: macb: fix sleep inside spinlock
net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
net: ethernet: mtk_eth_soc: fix pse_port configuration for MT7988
net: ethernet: mtk_eth_soc: fix uninitialized variable
kcm: Fix memory leak in error path of kcm_sendmsg()
r8152: check budget for r8152_poll()
net: dsa: sja1105: block FDB accesses that are concurrent with a switch reset
...
Eric Dumazet [Tue, 12 Sep 2023 09:17:30 +0000 (09:17 +0000)]
udplite: fix various data-races
udp->pcflag, udp->pcslen and udp->pcrlen reads/writes are racy.
Move udp->pcflag to udp->udp_flags for atomicity,
and add READ_ONCE()/WRITE_ONCE() annotations for pcslen and pcrlen.
Fixes: ba4e58eca8aa ("[NET]: Supporting UDP-Lite (RFC 3828) in Linux") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Dumazet [Tue, 12 Sep 2023 09:17:25 +0000 (09:17 +0000)]
udp: add missing WRITE_ONCE() around up->encap_rcv
UDP_ENCAP_ESPINUDP_NON_IKE setsockopt() writes over up->encap_rcv
while other cpus read it.
Fixes: 067b207b281d ("[UDP]: Cleanup UDP encapsulation code") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Dumazet [Tue, 12 Sep 2023 09:17:24 +0000 (09:17 +0000)]
udp: move udp->gro_enabled to udp->udp_flags
syzbot reported that udp->gro_enabled can be read locklessly.
Use one atomic bit from udp->udp_flags.
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Dumazet [Tue, 12 Sep 2023 09:17:23 +0000 (09:17 +0000)]
udp: move udp->no_check6_rx to udp->udp_flags
syzbot reported that udp->no_check6_rx can be read locklessly.
Use one atomic bit from udp->udp_flags.
Fixes: 1c19448c9ba6 ("net: Make enabling of zero UDP6 csums more restrictive") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Dumazet [Tue, 12 Sep 2023 09:17:22 +0000 (09:17 +0000)]
udp: move udp->no_check6_tx to udp->udp_flags
syzbot reported that udp->no_check6_tx can be read locklessly.
Use one atomic bit from udp->udp_flags
Fixes: 1c19448c9ba6 ("net: Make enabling of zero UDP6 csums more restrictive") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd720
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour.
Fixes: c821a88bd720 ("kcm: Fix memory leak in error path of kcm_sendmsg()") Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230912022753.33327-1-kuniyu@amazon.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
net: renesas: rswitch: Fix a lot of redundant irq issue
After this patch series was applied, a lot of redundant interrupts
no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
====================
net: renesas: rswitch: Add spin lock protection for irq {un}mask
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is based on alx driver commit 881d0327db37 ("net: alx: Work around
the DMA RX overflow issue").
The alx and atl1c drivers had RX overflow error which was why a custom
allocator was created to avoid certain addresses. The simpler workaround
then created for alx driver, but not for atl1c due to lack of tester.
Instead of using a custom allocator, check the allocated skb address and
use skb_reserve() to move away from problematic 0x...fc0 address.
====================
vsock: handle writes to shutdowned socket
this small patchset adds POSIX compliant behaviour on writes to the
socket which was shutdowned with 'shutdown()' (both sides - local with
SHUT_WR flag, peer - with SHUT_RD flag). According POSIX we must send
SIGPIPE in such cases (but SIGPIPE is not send when MSG_NOSIGNAL is set).
First patch is implemented in the same way as net/ipv4/tcp.c:tcp_sendmsg_locked().
It uses 'sk_stream_error()' function which handles EPIPE error. Another
way is to use code from net/unix/af_unix.c:unix_stream_sendmsg() where
same logic from 'sk_stream_error()' is implemented "from scratch", but
it doesn't check 'sk_err' field. I think error from this field has more
priority to be returned from syscall. So I guess it is better to reuse
currently implemented 'sk_stream_error()' function.
This adds two tests for 'shutdown()' call. It checks that SIGPIPE is
sent when MSG_NOSIGNAL is not set and vice versa. Both flags SHUT_WR
and SHUT_RD are tested.
POSIX requires to send SIGPIPE on write to SOCK_STREAM socket which was
shutdowned with SHUT_WR flag or its peer was shutdowned with SHUT_RD
flag. Also we must not send SIGPIPE if MSG_NOSIGNAL flag is set.
Merge tag 'pmdomain-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull genpm / pmdomain rename from Ulf Hansson:
"This renames the genpd subsystem to pmdomain.
As discussed on LKML, using 'genpd' as the name of a subsystem isn't
very self-explanatory and the acronym itself that means Generic PM
Domain, is known only by a limited group of people.
The suggestion to improve the situation is to rename the subsystem to
'pmdomain', which there seems to be a good consensus around using.
Ideally it should indicate that its purpose is to manage Power Domains
or 'PM domains' as we often also use within the Linux Kernel
terminology"
* tag 'pmdomain-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: Rename the genpd subsystem to pmdomain
Merge tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- fix reference to exported symbols for parisc64 [Masahiro Yamada]
- Block-TLB (BTLB) support on 32-bit CPUs
- sparse and build-warning fixes
* tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
linux/export: fix reference to exported functions for parisc64
parisc: BTLB: Initialize BTLB tables at CPU startup
parisc: firmware: Simplify calling non-PA20 functions
parisc: BTLB: _edata symbol has to be page aligned for BTLB support
parisc: BTLB: Add BTLB insert and purge firmware function wrappers
parisc: BTLB: Clear possibly existing BTLB entries
parisc: Prepare for Block-TLB support on 32-bit kernel
parisc: shmparam.h: Document aliasing requirements of PA-RISC
parisc: irq: Make irq_stack_union static to avoid sparse warning
parisc: drivers: Fix sparse warning
parisc: iosapic.c: Fix sparse warnings
parisc: ccio-dma: Fix sparse warnings
parisc: sba-iommu: Fix sparse warnigs
parisc: sba: Fix compile warning wrt list of SBA devices
parisc: sba_iommu: Fix build warning if procfs if disabled
Merge tag 'trace-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Add missing LOCKDOWN checks for eventfs callers
When LOCKDOWN is active for tracing, it causes inconsistent state
when some functions succeed and others fail.
- Use dput() to free the top level eventfs descriptor
There was a race between accesses and freeing it.
- Fix a long standing bug that eventfs exposed due to changing timings
by dynamically creating files. That is, If a event file is opened for
an instance, there's nothing preventing the instance from being
removed which will make accessing the files cause use-after-free
bugs.
- Fix a ring buffer race that happens when iterating over the ring
buffer while writers are active. Check to make sure not to read the
event meta data if it's beyond the end of the ring buffer sub buffer.
- Fix the print trigger that disappeared because the test to create it
was looking for the event dir field being filled, but now it has the
"ef" field filled for the eventfs structure.
- Remove the unused "dir" field from the event structure.
- Fix the order of the trace_dynamic_info as it had it backwards for
the offset and len fields for which one was for which endianess.
- Fix NULL pointer dereference with eventfs_remove_rec()
If an allocation fails in one of the eventfs_add_*() functions, the
caller of it in event_subsystem_dir() or event_create_dir() assigns
the result to the structure. But it's assigning the ERR_PTR and not
NULL. This was passed to eventfs_remove_rec() which expects either a
good pointer or a NULL, not ERR_PTR. The fix is to not assign the
ERR_PTR to the structure, but to keep it NULL on error.
- Fix list_for_each_rcu() to use list_for_each_srcu() in
dcache_dir_open_wrapper(). One iteration of the code used RCU but
because it had to call sleepable code, it had to be changed to use
SRCU, but one of the iterations was missed.
- Fix synthetic event print function to use "as_u64" instead of passing
in a pointer to the union. To fix big/little endian issues, the u64
that represented several types was turned into a union to define the
types properly.
* tag 'trace-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Fix the NULL pointer dereference bug in eventfs_remove_rec()
tracefs/eventfs: Use list_for_each_srcu() in dcache_dir_open_wrapper()
tracing/synthetic: Print out u64 values properly
tracing/synthetic: Fix order of struct trace_dynamic_info
selftests/ftrace: Fix dependencies for some of the synthetic event tests
tracing: Remove unused trace_event_file dir field
tracing: Use the new eventfs descriptor for print trigger
ring-buffer: Do not attempt to read past "commit"
tracefs/eventfs: Free top level files on removal
ring-buffer: Avoid softlockup in ring_buffer_resize()
tracing: Have event inject files inc the trace array ref count
tracing: Have option files inc the trace array ref count
tracing: Have current_trace inc the trace array ref count
tracing: Have tracing_max_latency inc the trace array ref count
tracing: Increase trace array ref count on enable and filter files
tracefs/eventfs: Use dput to free the toplevel events directory
tracefs/eventfs: Add missing lockdown checks
tracefs: Add missing lockdown check to tracefs_create_dir()
v2->v3: https://lore.kernel.org/all/20230825155148.659895-1-pctammela@mojatatu.com/
- Added changes that were left in the working tree (Jakub)
- Fixed two typos in commit message titles
- Added Victor tags
v1->v2: https://lore.kernel.org/all/20230818163544.351104-1-pctammela@mojatatu.com/
- Drop u32 updates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Mon, 11 Sep 2023 21:50:16 +0000 (18:50 -0300)]
net/sched: cls_route: make netlink errors meaningful
Use netlink extended ack and parsing policies to return more meaningful
errors instead of the relying solely on errnos.
Reviewed-by: Victor Nogueira <victor@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Mon, 11 Sep 2023 21:50:15 +0000 (18:50 -0300)]
selftests/tc-testing: cls_u32: add tests for classid
As discussed in '3044b16e7c6f', cls_u32 was handling the use of classid
incorrectly. Add a test to check if it's conforming to the correct
behaviour.
Reviewed-by: Victor Nogueira <victor@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Mon, 11 Sep 2023 21:50:14 +0000 (18:50 -0300)]
selftests/tc-testing: cls_route: add tests for classid
As discussed in 'b80b829e9e2c', cls_route was handling the use of classid
incorrectly. Add a test to check if it's conforming to the correct
behaviour.
Reviewed-by: Victor Nogueira <victor@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Mon, 11 Sep 2023 21:50:13 +0000 (18:50 -0300)]
selftests/tc-testing: cls_fw: add tests for classid
As discussed in '76e42ae83199', cls_fw was handling the use of classid
incorrectly. Add a few tests to check if it's conforming to the correct
behaviour.
Reviewed-by: Victor Nogueira <victor@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
igb: clean up in all error paths when enabling SR-IOV
After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails.
Fixes: 50f303496d92 ("igb: Enable SR-IOV after reinit") Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The commit in fixes introduced flags to control the status of hardware
configuration while processing packets. At the same time another structure
is used to provide configuration of timestamper to user-space applications.
The way it was coded makes this structures go out of sync easily. The
repro is easy for 82599 chips:
The eth0 device is properly configured to timestamp any PTPv2 events.
[root@hostname ~]# hwstamp_ctl -i eth0 -r 1 -t 1
current settings:
tx_type 1
rx_filter 12
SIOCSHWTSTAMP failed: Numerical result out of range
The requested time stamping mode is not supported by the hardware.
The error is properly returned because HW doesn't support all packets
timestamping. But the adapter->flags is cleared of timestamp flags
even though no HW configuration was done. From that point no RX timestamps
are received by user-space application. But configuration shows good
values:
Fix the issue by applying new flags only when the HW was actually
configured.
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices") Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_kasprintf() instead of hand writing it.
This is less verbose and less error prone.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
It has been pointed out that naming a subsystem "genpd" isn't very
self-explanatory and the acronym itself that means Generic PM Domain, is
known only by a limited group of people.
In a way to improve the situation, let's rename the subsystem to pmdomain,
which ideally should indicate that this is about so called Power Domains or
"PM domains" as we often also use within the Linux Kernel terminology.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Rafael J. Wysocki <rafael@kernel.org> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20230912221127.487327-1-ulf.hansson@linaro.org
Just after bhash2:
$ uname -r 6.0.0-rc1-00394-g28044fc1d495
$ ./bind_wildcard
...
ok 15 bind_wildcard.v4_local_v6_v4mapped_local.v4_v6
not ok 16 bind_wildcard.v4_local_v6_v4mapped_local.v6_v4
# FAILED: 15 / 16 tests passed.
On net.git:
$ ./bind_wildcard
...
not ok 14 bind_wildcard.v4_local_v6_v4mapped_any.v6_v4
not ok 16 bind_wildcard.v4_local_v6_v4mapped_local.v6_v4
# FAILED: 13 / 16 tests passed.
With this series:
$ ./bind_wildcard
...
# PASSED: 16 / 16 tests passed.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftest: tcp: Fix address length in bind_wildcard.c.
The selftest passes the IPv6 address length for an IPv4 address.
We should pass the correct length.
Note inet_bind_sk() does not check if the size is larger than
sizeof(struct sockaddr_in), so there is no real bug in this
selftest.
Fixes: 13715acf8ab5 ("selftest: Add test for bind() conflicts.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During the 2nd bind() in inet_csk_get_port(), inet_bind2_bucket_find()
fails to find the 1st socket's tb2, so inet_bind2_bucket_create() allocates
a new tb2 for the 2nd socket. Then, we call inet_csk_bind_conflict() that
checks conflicts in the new tb2 by inet_bhash2_conflict(). However, the
new tb2 does not include the 1st socket, thus the bind() finally succeeds.
In this case, inet_bind2_bucket_match() must check if AF_INET6 tb2 has
the conflicting v4-mapped-v6 address so that inet_bind2_bucket_find()
returns the 1st socket's tb2.
Note that if we bind two sockets to 127.0.0.1 and then ::FFFF:127.0.0.1,
the 2nd bind() fails properly for the same reason mentinoed in the previous
commit.
Fixes: 28044fc1d495 ("net: Add a bhash2 table hashed by port and address") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Andrei Vagin <avagin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During the 2nd bind(), if tb->family is AF_INET6 and sk->sk_family is
AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the v4-mapped-v6 wildcard address.
The example above does not work after commit 5456262d2baa ("net: Fix
incorrect address comparison when searching for a bind2 bucket"), but
the blamed change is not the commit.
Before the commit, the leading zeros of ::FFFF:0.0.0.0 were treated
as 0.0.0.0, and the sequence above worked by chance. Technically, this
case has been broken since bhash2 was introduced.
Note that if we bind() two sockets to 127.0.0.1 and then ::FFFF:0.0.0.0,
the 2nd bind() fails properly because we fall back to using bhash to
detect conflicts for the v4-mapped-v6 address.
Fixes: 28044fc1d495 ("net: Add a bhash2 table hashed by port and address") Reported-by: Andrei Vagin <avagin@google.com> Closes: https://lore.kernel.org/netdev/ZPuYBOFC8zsK6r9T@google.com/ Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: Factorise sk_family-independent comparison in inet_bind2_bucket_match(_addr_any).
This is a prep patch to make the following patches cleaner that touch
inet_bind2_bucket_match() and inet_bind2_bucket_match_addr_any().
Both functions have duplicated comparison for netns, port, and l3mdev.
Let's factorise them.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 13 Sep 2023 05:50:58 +0000 (06:50 +0100)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-09-11 (i40e, iavf)
This series contains updates to i40e and iavf drivers.
Andrii ensures all VSIs are cleaned up for remove in i40e.
Brett reworks logic for setting promiscuous mode that can, currently, cause
incorrect states on iavf.
---
v2:
- Remove redundant i40e_vsi_free_q_vectors() and kfree() calls (patch 1)
Commit d2e8071bed0be ("tpm: make all 'class' structures const")
unfortunately had a typo for the name on tpmrm.
Fixes: d2e8071bed0b ("tpm: make all 'class' structures const") Signed-off-by: Justin M. Forbes <jforbes@fedoraproject.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Merge tag 'for-6.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- several fixes for handling directory item (inserting, removing,
iteration, error handling)
- fix transaction commit stalls when auto relocation is running and
blocks other tasks that want to commit
- fix a build error when DEBUG is enabled
- fix lockdep warning in inode number lookup ioctl
- fix race when finishing block group creation
- remove link to obsolete wiki in several files
* tag 'for-6.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
MAINTAINERS: remove links to obsolete btrfs.wiki.kernel.org
btrfs: assert delayed node locked when removing delayed item
btrfs: remove BUG() after failure to insert delayed dir index item
btrfs: improve error message after failure to add delayed dir index item
btrfs: fix a compilation error if DEBUG is defined in btree_dirty_folio
btrfs: check for BTRFS_FS_ERROR in pending ordered assert
btrfs: fix lockdep splat and potential deadlock after failure running delayed items
btrfs: do not block starts waiting on previous transaction commit
btrfs: release path before inode lookup during the ino lookup ioctl
btrfs: fix race between finishing block group creation and its item update
Merge tag 'platform-drivers-x86-v6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- various platform/mellanox fixes
- one new DMI quirk for asus-wmi
* tag 'platform-drivers-x86-v6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Support 2023 ROG X16 tablet mode
platform/mellanox: NVSW_SN2201 should depend on ACPI
platform/mellanox: mlxbf-bootctl: add NET dependency into Kconfig
platform/mellanox: mlxbf-pmc: Fix reading of unprogrammed events
platform/mellanox: mlxbf-pmc: Fix potential buffer overflows
platform/mellanox: mlxbf-tmfifo: Drop jumbo frames
platform/mellanox: mlxbf-tmfifo: Drop the Rx packet if no more descriptors
First patches are mostly preparing the ground for the last one.
Last patch of the series implements sort of ACK reduction
only for the cases a TCP receiver is under high stress,
which happens for high throughput flows.
This gives us a ~20% increase of single TCP flow (100Gbit -> 120Gbit)
====================
Eric Dumazet [Mon, 11 Sep 2023 17:05:31 +0000 (17:05 +0000)]
tcp: defer regular ACK while processing socket backlog
This idea came after a particular workload requested
the quickack attribute set on routes, and a performance
drop was noticed for large bulk transfers.
For high throughput flows, it is best to use one cpu
running the user thread issuing socket system calls,
and a separate cpu to process incoming packets from BH context.
(With TSO/GRO, bottleneck is usually the 'user' cpu)
Problem is the user thread can spend a lot of time while holding
the socket lock, forcing BH handler to queue most of incoming
packets in the socket backlog.
Whenever the user thread releases the socket lock, it must first
process all accumulated packets in the backlog, potentially
adding latency spikes. Due to flood mitigation, having too many
packets in the backlog increases chance of unexpected drops.
Backlog processing unfortunately shifts a fair amount of cpu cycles
from the BH cpu to the 'user' cpu, thus reducing max throughput.
This patch takes advantage of the backlog processing,
and the fact that ACK are mostly cumulative.
The idea is to detect we are in the backlog processing
and defer all eligible ACK into a single one,
sent from tcp_release_cb().
This saves cpu cycles on both sides, and network resources.
Performance of a single TCP flow on a 200Gbit NIC:
- Throughput is increased by 20% (100Gbit -> 120Gbit).
- Number of generated ACK per second shrinks from 240,000 to 40,000.
- Number of backlog drops per second shrinks from 230 to 0.
* tag 'linux-kselftest-next-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Keep symlinks, when possible
selftests: fix dependency checker script
kselftest/runner.sh: Propagate SIGTERM to runner child
selftests/ftrace: Correctly enable event in instance-event.tc
Merge tag 'linux-kselftest-kunit-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan:
"Fixes to possible memory leak, null-ptr-deref, wild-memory-access, and
error path bugs"
* tag 'linux-kselftest-kunit-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: Fix possible memory leak in kunit_filter_suites()
kunit: Fix possible null-ptr-deref in kunit_parse_glob_filter()
kunit: Fix the wrong err path and add goto labels in kunit_filter_suites()
kunit: Fix wild-memory-access bug in kunit_free_suite_set()
kunit: test: Make filter strings in executor_test writable
Merge tag 'ovl-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Amir Goldstein:
"Two fixes for pretty old regressions"
* tag 'ovl-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix incorrect fdput() on aio completion
ovl: fix failed copyup of fileattr on a symlink
veth: Update XDP feature set when bringing up device
There's an early return in veth_set_features() if the device is in a down
state, which leads to the XDP feature flags not being updated when enabling
GRO while the device is down. Which in turn leads to XDP_REDIRECT not
working, because the redirect code now checks the flags.
Fix this by updating the feature flags after bringing the device up.
Before this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: no
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: no
After this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: yes
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: yes
Fixes: fccca038f300 ("veth: take into account device reconfiguration for xdp_features flag") Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/r/20230911135826.722295-1-toke@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
eventfs: Fix the NULL pointer dereference bug in eventfs_remove_rec()
Inject fault while probing btrfs.ko, if kstrdup() fails in
eventfs_prepare_ef() in eventfs_add_dir(), it will return ERR_PTR
to assign file->ef. But the eventfs_remove() check NULL in
trace_module_remove_events(), which causes the below NULL
pointer dereference.
As both Masami and Steven suggest, allocater side should handle the
error carefully and remove it, so fix the places where it failed.
The obvious fix is to move the call to macb_set_tx_clk() out of the
protected area. This seems safe as rx and tx are both disabled anyway at
this point.
It is however not entirely clear what the spinlock shall protect. It
could be the read-modify-write access to the NCFGR register, but this
is accessed in macb_set_rx_mode() and macb_set_rxcsum_feature() as well
without holding the spinlock. It could also be the register accesses
done in mog_init_rings() or macb_init_buffers(), but again these
functions are called without holding the spinlock in macb_hresp_error_task().
The locking seems fishy in this driver and it might deserve another look
before this patch is applied.
net: dst: remove unnecessary input parameter in dst_alloc and dst_init
Since commit 1202cdd66531("Remove DECnet support from kernel") has been
merged, all callers pass in the initial_ref value of 1 when they call
dst_alloc(). Therefore, remove initial_ref when the dst_alloc() is
declared and replace initial_ref with 1 in dst_alloc().
Also when all callers call dst_init(), the value of initial_ref is 1.
Therefore, remove the input parameter initial_ref of the dst_init() and
replace initial_ref with the value 1 in dst_init.
Paolo Abeni [Tue, 12 Sep 2023 08:23:53 +0000 (10:23 +0200)]
Merge branch 'add-support-for-icssg-on-am64x-evm'
MD Danish Anwar says:
====================
Add support for ICSSG on AM64x EVM
This series adds support for ICSSG driver on AM64x EVM.
First patch of the series adds compatible for AM64x EVM in icssg-prueth
dt binding. Second patch adds support for AM64x compatible in the ICSSG
driver.
This series addresses comments on [v1] (which was posted as RFC).
This series is based on the latest net-next/main. This series has no
dependency.
Changes from v1 to v2:
*) Made the compatible list in patch 1 alphanumerically ordered as asked
by Krzysztof.
*) Dropped the RFC tag.
*) Added RB tags of Andrew and Roger.
Add AM64x ICSSG support which is similar to am65x SR2.0, but required:
- all ring configured in exposed ring mode
- always fill both original and buffer fields in cppi5 desc
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Liu Jian [Sat, 9 Sep 2023 08:14:34 +0000 (16:14 +0800)]
net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
I got the below warning when do fuzzing test:
BUG: KASAN: null-ptr-deref in scatterwalk_copychunks+0x320/0x470
Read of size 4 at addr 0000000000000008 by task kworker/u8:1/9
This is because the value of rec_seq of tls_crypto_info configured by the
user program is too large, for example, 0xffffffffffffff. In addition, TLS
is asynchronously accelerated. When tls_do_encryption() returns
-EINPROGRESS and sk->sk_err is set to EBADMSG due to rec_seq overflow,
skmsg is released before the asynchronous encryption process ends. As a
result, the UAF problem occurs during the asynchronous processing of the
encryption module.
If the operation is asynchronous and the encryption module returns
EINPROGRESS, do not free the record information.
Fixes: 635d93981786 ("net/tls: free record only on encryption error") Signed-off-by: Liu Jian <liujian56@huawei.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Link: https://lore.kernel.org/r/20230909081434.2324940-1-liujian56@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
tracefs/eventfs: Use list_for_each_srcu() in dcache_dir_open_wrapper()
The eventfs files list is protected by SRCU. In earlier iterations it was
protected with just RCU, but because it needed to also call sleepable
code, it had to be switch to SRCU. The dcache_dir_open_wrapper()
list_for_each_rcu() was missed and did not get converted over to
list_for_each_srcu(). That needs to be fixed.
Tero Kristo [Mon, 11 Sep 2023 14:17:04 +0000 (17:17 +0300)]
tracing/synthetic: Print out u64 values properly
The synth traces incorrectly print pointer to the synthetic event values
instead of the actual value when using u64 type. Fix by addressing the
contents of the union properly.
Currently when configuring promiscuous mode on the AVF we detect a
change in the netdev->flags. We use IFF_PROMISC and IFF_ALLMULTI to
determine whether or not we need to request/release promiscuous mode
and/or multicast promiscuous mode. The problem is that the AQ calls for
setting/clearing promiscuous/multicast mode are treated separately. This
leads to a case where we can trigger two promiscuous mode AQ calls in
a row with the incorrect state. To fix this make a few changes.
Use IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE instead of the previous
IAVF_FLAG_AQ_[REQUEST|RELEASE]_[PROMISC|ALLMULTI] flags.
In iavf_set_rx_mode() detect if there is a change in the
netdev->flags in comparison with adapter->flags and set the
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE aq_required bit. Then in
iavf_process_aq_command() only check for IAVF_FLAG_CONFIGURE_PROMISC_MODE
and call iavf_set_promiscuous() if it's set.
In iavf_set_promiscuous() check again to see which (if any) promiscuous
mode bits have changed when comparing the netdev->flags with the
adapter->flags. Use this to set the flags which get sent to the PF
driver.
Add a spinlock that is used for updating current_netdev_promisc_flags
and only allows one promiscuous mode AQ at a time.
[1] Fixes the fact that we will only have one AQ call in the aq_required
queue at any one time.
[2] Streamlines the change in promiscuous mode to only set one AQ
required bit.
[3] This allows us to keep track of the current state of the flags and
also makes it so we can take the most recent netdev->flags promiscuous
mode state.
[4] This fixes the problem where a change in the netdev->flags can cause
IAVF_FLAG_AQ_CONFIGURE_PROMISC_MODE to be set in iavf_set_rx_mode(),
but cleared in iavf_set_promiscuous() before the change is ever made via
AQ call.
Fixes: 47d3483988f6 ("i40evf: Add driver support for promiscuous mode") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of freeing memory of a single VSI, make sure
the memory for all VSIs is cleared before releasing VSIs.
Add releasing of their resources in a loop with the iteration
number equal to the number of allocated VSIs.
Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Andrii Staikov <andrii.staikov@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
platform/mellanox: NVSW_SN2201 should depend on ACPI
The only probing method supported by the Nvidia SN2201 platform driver
is probing through an ACPI match table. Hence add a dependency on
ACPI, to prevent asking the user about this driver when configuring a
kernel without ACPI support.
projects / users / jedix / linux-maple.git / log