It was observed that sending data via batadv over vxlan (on top of
wireguard) reduced the performance massively compared to raw ethernet or
batadv on raw ethernet. A check of perf data showed that the
vxlan_build_skb was calling all the time pskb_expand_head to allocate
enough headroom for:
But the vxlan_config_apply only requested needed headroom for:
lowerdev->hard_header_len + VXLAN6_HEADROOM or VXLAN_HEADROOM
So it completely ignored the needed_headroom of the lower device. The first
caller of net_dev_xmit could therefore never make sure that enough headroom
was allocated for the rest of the transmit path.
In el0_svc_common() we unmask exceptions before we call user_exit(), and
so there's a window where an IRQ or debug exception can be taken while
RCU is not watching. In do_debug_exception() we account for this in via
debug_exception_{enter,exit}(), but in the el1_irq asm we do not and we
call trace functions which rely on RCU before we have a guarantee that
RCU is watching.
Let's avoid this by having el0_svc_common() exit userspace before
unmasking exceptions, matching what we do for all other EL0 entry paths.
We can use user_exit_irqoff() to avoid the pointless save/restore of IRQ
flags while we're sure exceptions are masked in DAIF.
The workaround for Cortex-A76 erratum 1463225 may trigger a debug
exception before this point, but the debug code invoked in this case is
safe even when RCU is not watching.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: James Morse <james.morse@arm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20201130115950.22492-2-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
powerpc/64s keeps a counter in the mm which counts bits set in
mm_cpumask as well as other things. This means it can't use generic code
to clear bits out of the mask and doesn't adjust the arch specific
counter.
Add an arch override that allows powerpc/64s to use
clear_tasks_mm_cpumask().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20201126102530.691335-4-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
idr_init() uses base 0 which is an invalid identifier for this driver.
The new function idr_init_base allows IDR to set the ID lookup from
base 1. This avoids all lookups that otherwise starts from 0 since
0 is always unused.
References: commit 6ce711f27500 ("idr: Make 1-based IDRs more efficient")
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Fixes: 6453073987ba ("ixgbe: add initial support for xdp redirect") Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When setting the ethtool feature flag fails (as expected for the test), the
kernel now tracks that the feature was requested to be 'off' and refuses to
subsequently disable it again. So reset it back to 'on' so a subsequent
disable (that's not supposed to fail) can succeed.
Fixes: 417ec26477a5 ("selftests/bpf: add offload test based on netdevsim") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/bpf/160752226280.110217.10696241563705667871.stgit@toke.dk Signed-off-by: Sasha Levin <sashal@kernel.org>
EIC controller have unfixed numbers of banks on different Spreadtrum SoCs,
and each bank has its own base address, the loop of getting there base
address in driver should break if the resource gotten via
platform_get_resource() is NULL already. The later ones would be all NULL
even if the loop continues.
When running concurrent iptables rules replacement with data, the per CPU
sequence count is checked after the assignment of the new information.
The sequence count is used to synchronize with the packet path without the
use of any explicit locking. If there are any packets in the packet path using
the table information, the sequence count is incremented to an odd value and
is incremented to an even after the packet process completion.
The new table value assignment is followed by a write memory barrier so every
CPU should see the latest value. If the packet path has started with the old
table information, the sequence counter will be odd and the iptables
replacement will wait till the sequence count is even prior to freeing the
old table info.
However, this assumes that the new table information assignment and the memory
barrier is actually executed prior to the counter check in the replacement
thread. If CPU decides to execute the assignment later as there is no user of
the table information prior to the sequence check, the packet path in another
CPU may use the old table information. The replacement thread would then free
the table information under it leading to a use after free in the packet
processing context-
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000008e
pc : ip6t_do_table+0x5d0/0x89c
lr : ip6t_do_table+0x5b8/0x89c
ip6t_do_table+0x5d0/0x89c
ip6table_filter_hook+0x24/0x30
nf_hook_slow+0x84/0x120
ip6_input+0x74/0xe0
ip6_rcv_finish+0x7c/0x128
ipv6_rcv+0xac/0xe4
__netif_receive_skb+0x84/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
This could be fixed by forcing instruction order after the new table
information assignment or by switching to RCU for the synchronization.
Fixes: 80055dab5de0 ("netfilter: x_tables: make xt_replace_table wait until old rules are not used anymore") Reported-by: Sean Tranchetti <stranche@codeaurora.org> Reported-by: kernel test robot <lkp@intel.com> Suggested-by: Florian Westphal <fw@strlen.de> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The R9A06G032 clock driver uses an array of packed structures to reduce
kernel size. However, this array contains pointers, which are no longer
aligned naturally, and cannot be relocated on PPC64. Hence when
compile-testing this driver on PPC64 with CONFIG_RELOCATABLE=y (e.g.
PowerPC allyesconfig), the following warnings are produced:
Fix this by dropping the __packed attribute from the r9a06g032_clkdesc
definition, trading a small size increase for portability.
This increases the 156-entry clock table by 1 byte per entry, but due to
the compiler generating more efficient code for unpacked accesses, the
net size increase is only 76 bytes (gcc 9.3.0 on arm32).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: 4c3d88526eba2143 ("clk: renesas: Renesas R9A06G032 clock driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20201130085743.1656317-1-geert+renesas@glider.be Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # PowerPC allyesconfig build Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
The MBA software controller (mba_sc) is a feedback loop which
periodically reads MBM counters and tries to restrict the bandwidth
below a user-specified value. It tags along the MBM counter overflow
handler to do the updates with 1s interval in mbm_update() and
update_mba_bw().
The purpose of mbm_update() is to periodically read the MBM counters to
make sure that the hardware counter doesn't wrap around more than once
between user samplings. mbm_update() calls __mon_event_count() for local
bandwidth updating when mba_sc is not enabled, but calls mbm_bw_count()
instead when mba_sc is enabled. __mon_event_count() will not be called
for local bandwidth updating in MBM counter overflow handler, but it is
still called when reading MBM local bandwidth counter file
'mbm_local_bytes', the call path is as below:
In __mon_event_count(), m->chunks is updated by delta chunks which is
calculated from previous MSR value (m->prev_msr) and current MSR value.
When mba_sc is enabled, m->chunks is also updated in mbm_update() by
mistake by the delta chunks which is calculated from m->prev_bw_msr
instead of m->prev_msr. But m->chunks is not used in update_mba_bw() in
the mba_sc feedback loop.
When reading MBM local bandwidth counter file, m->chunks was changed
unexpectedly by mbm_bw_count(). As a result, the incorrect local
bandwidth counter which calculated from incorrect m->chunks is shown to
the user.
Fix this by removing incorrect m->chunks updating in mbm_bw_count() in
MBM counter overflow handler, and always calling __mon_event_count() in
mbm_update() to make sure that the hardware local bandwidth counter
doesn't wrap around.
Test steps:
# Run workload with aggressive memory bandwidth (e.g., 10 GB/s)
git clone https://github.com/intel/intel-cmt-cat && cd intel-cmt-cat
&& make
./tools/membw/membw -c 0 -b 10000 --read
# Enable MBA software controller
mount -t resctrl resctrl -o mba_MBps /sys/fs/resctrl
# Create control group c1
mkdir /sys/fs/resctrl/c1
# Set MB throttle to 6 GB/s
echo "MB:0=6000;1=6000" > /sys/fs/resctrl/c1/schemata
# Write PID of the workload to tasks file
echo `pidof membw` > /sys/fs/resctrl/c1/tasks
# Read local bytes counters twice with 1s interval, the calculated
# local bandwidth is not as expected (approaching to 6 GB/s):
local_1=`cat /sys/fs/resctrl/c1/mon_data/mon_L3_00/mbm_local_bytes`
sleep 1
local_2=`cat /sys/fs/resctrl/c1/mon_data/mon_L3_00/mbm_local_bytes`
echo "local b/w (bytes/s):" `expr $local_2 - $local_1`
Commit 39d114ddc682 ("arm64: add KASAN support") added .weak directives to
arch/arm64/lib/mem*.S instead of changing the existing SYM_FUNC_START_PI
macros. This can lead to the assembly snippet `.weak memcpy ... .globl
memcpy` which will produce a STB_WEAK memcpy with GNU as but STB_GLOBAL
memcpy with LLVM's integrated assembler before LLVM 12. LLVM 12 (since
https://reviews.llvm.org/D90108) will error on such an overridden symbol
binding.
Use the appropriate SYM_FUNC_START_WEAK_PI instead.
Fixes: 39d114ddc682 ("arm64: add KASAN support") Reported-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Fangrui Song <maskray@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201029181951.1866093-1-maskray@google.com Signed-off-by: Will Deacon <will@kernel.org>
[nd: backport to adjust for missing:
commit 3ac0f4526dfb ("arm64: lib: Use modern annotations for assembly functions")
commit 35e61c77ef38 ("arm64: asm: Add new-style position independent function annotations")] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0d5896bd356 ("arm64: lse: fix LSE atomics with LLVM's integrated
assembler") broke the build when clang is used in connjunction with the
binutils assembler ("-no-integrated-as"). This happens because
__LSE_PREAMBLE is defined as ".arch armv8-a+lse", which overrides the
version of the CPU architecture passed via the "-march" paramter to gas:
$ aarch64-none-linux-gnu-as -EL -I ./arch/arm64/include
-I ./arch/arm64/include/generated
-I ./include -I ./include
-I ./arch/arm64/include/uapi
-I ./arch/arm64/include/generated/uapi
-I ./include/uapi -I ./include/generated/uapi
-I ./init -I ./init
-march=armv8.3-a -o init/do_mounts.o
/tmp/do_mounts-d7992a.s
/tmp/do_mounts-d7992a.s: Assembler messages:
/tmp/do_mounts-d7992a.s:1959: Error: selected processor does not support `autiasp'
/tmp/do_mounts-d7992a.s:2021: Error: selected processor does not support `paciasp'
/tmp/do_mounts-d7992a.s:2157: Error: selected processor does not support `autiasp'
/tmp/do_mounts-d7992a.s:2175: Error: selected processor does not support `paciasp'
/tmp/do_mounts-d7992a.s:2494: Error: selected processor does not support `autiasp'
Fix the issue by replacing ".arch armv8-a+lse" with ".arch_extension lse".
Sami confirms that the clang integrated assembler does now support the
'.arch_extension' directive, so this change will be fine even for LTO
builds in future.
Fixes: e0d5896bd356cd ("arm64: lse: fix LSE atomics with LLVM's integrated assembler") Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Reported-by: Amit Kachhap <Amit.Kachhap@arm.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike gcc, clang considers each inline assembly block to be independent
and therefore, when using the integrated assembler for inline assembly,
any preambles that enable features must be repeated in each block.
This change defines __LSE_PREAMBLE and adds it to each inline assembly
block that has LSE instructions, which allows them to be compiled also
with clang's assembler.
Link: https://github.com/ClangBuiltLinux/linux/issues/671 Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Andrew Murray <andrew.murray@arm.com> Tested-by: Kees Cook <keescook@chromium.org> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Will Deacon <will@kernel.org>
[nd: backport adjusted due to missing:
commit addfc38672c7 ("arm64: atomics: avoid out-of-line ll/sc atomics")] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_dp_mst_allocate_vcpi() invokes
drm_dp_mst_topology_get_port_validated(), which increases the refcount
of the "port".
These reference counting issues take place in two exception handling
paths separately. Either when “slots” is less than 0 or when
drm_dp_init_vcpi() returns a negative value, the function forgets to
reduce the refcnt increased drm_dp_mst_topology_get_port_validated(),
which results in a refcount leak.
Fix these issues by pulling up the error handling when "slots" is less
than 0, and calling drm_dp_mst_topology_put_port() before termination
when drm_dp_init_vcpi() returns a negative value.
Fixes: 1e797f556c61 ("drm/dp: Split drm_dp_mst_allocate_vcpi") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200719154545.GA41231@xin-virtual-machine
[sudip: use old functions before rename] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
syzbot spotted a potential out-of-bounds shift in the PCM OSS layer
where it calculates the buffer size with the arbitrary shift value
given via an ioctl.
Add a range check for avoiding the undefined behavior.
As the value can be treated by a signed integer, the max shift should
be 30.
The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.
in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.
There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.
UAS does not share the pessimistic assumption storage is making that
devices cannot deal with WRITE_SAME. A few devices supported by UAS,
are reported to not deal well with WRITE_SAME. Those need a quirk.
Add it to the device that needs it.
Reported-by: David C. Partridge <david.partridge@perdrix.co.uk> Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201209152639.9195-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
If the size of the error log is too big to send via email, and the sending
fails, it wont email any result. This can be confusing for the user who is
waiting for an email on the completion of the tests.
If it fails to send email, then try again without the log file stating that
it failed to send an email. Obviously this will not be of use if the sending
of email failed for some other reasons, but it will at least give the user
some information when it fails for the most common reason.
Cc: stable@vger.kernel.org Fixes: c2d84ddb338c8 ("ktest.pl: Add MAIL_COMMAND option to define how to send email") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2ae0b ("stmmac: add the Energy Efficient Ethernet support") Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case error CQE was found while polling TX CQ, the QP is in error
state and all posted WQEs will generate error CQEs without any data
transmitted. Fix it by reopening the channels, via same method used for
TX timeout handling.
In addition add some more info on error CQE and WQE for debug.
Fixes: bd2f631d7c60 ("net/mlx4_en: Notify user when TX ring in error state") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous versions can be found at:
v1:
initial version
https://lkml.org/lkml/2020/10/28/921
v2:
do not return from lan743x_ethtool_set_wol if netdev->phydev == NULL, just skip
the call of phy_ethtool_set_wol() instead.
https://lkml.org/lkml/2020/10/31/380
v3:
in function lan743x_ethtool_set_wol:
use ternary operator instead of if-else sentence (review by Markus Elfring)
return -ENETDOWN insted of -EIO (review by Andrew Lunn)
Add restarting state flag to avoid scheduling another restart task while
such task is already running. Change task name from watchdog_task to
restart_task to better fit the task role.
Fixes: 1e338db56e5a ("mlx4_en: Fix a race at restart task") Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cwnd is not a multiple of the TSO skb size of N*MSS, we can get
into persistent scenarios where we have the following sequence:
(1) ACK for full-sized skb of N*MSS arrives
-> tcp_write_xmit() transmit full-sized skb with N*MSS
-> move pacing release time forward
-> exit tcp_write_xmit() because pacing time is in the future
(2) TSQ callback or TCP internal pacing timer fires
-> try to transmit next skb, but TSO deferral finds remainder of
available cwnd is not big enough to trigger an immediate send
now, so we defer sending until the next ACK.
(3) repeat...
So we can get into a case where we never mark ourselves as
cwnd-limited for many seconds at a time, even with
bulk/infinite-backlog senders, because:
o In case (1) above, every time in tcp_write_xmit() we have enough
cwnd to send a full-sized skb, we are not fully using the cwnd
(because cwnd is not a multiple of the TSO skb size). So every time we
send data, we are not cwnd limited, and so in the cwnd-limited
tracking code in tcp_cwnd_validate() we mark ourselves as not
cwnd-limited.
o In case (2) above, every time in tcp_write_xmit() that we try to
transmit the "remainder" of the cwnd but defer, we set the local
variable is_cwnd_limited to true, but we do not send any packets, so
sent_pkts is zero, so we don't call the cwnd-limited logic to update
tp->is_cwnd_limited.
Fixes: ca8a22634381 ("tcp: make cwnd-limited checks measurement-based, and gentler") Reported-by: Ingemar Johansson <ingemar.s.johansson@ericsson.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20201209035759.1225145-1-ncardwell.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
small tcp_rmem[1] values were overridden by tcp_fixup_rcvbuf() to accommodate various MSS.
This is no longer the case, and Hazem Mohamed Abuelfotoh reported
that DRS would not work for MTU 9000 endpoints receiving regular (1500 bytes) frames.
Root cause is that tcp_init_buffer_space() uses tp->rcv_wnd for upper limit
of rcvq_space.space computation, while it can select later a smaller
value for tp->rcv_ssthresh and tp->window_clamp.
Based on an initial report and patch from Hazem Mohamed Abuelfotoh
https://lore.kernel.org/netdev/20201204180622.14285-1-abuehaze@amazon.com/
Fixes: a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB") Fixes: 041a14d26715 ("tcp: start receiver buffer autotuning sooner") Reported-by: Hazem Mohamed Abuelfotoh <abuehaze@amazon.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do suspend/resume test, there have WARN_ON() log dump from
stmmac_xmit() funciton, the code logic:
entry = tx_q->cur_tx;
first_entry = entry;
WARN_ON(tx_q->tx_skbuff[first_entry]);
In normal case, tx_q->tx_skbuff[txq->cur_tx] should be NULL because
the skb should be handled and freed in stmmac_tx_clean().
But stmmac_resume() reset queue parameters like below, skb buffers
may not be freed.
tx_q->cur_tx = 0;
tx_q->dirty_tx = 0;
So free tx skb buffer in stmmac_resume() to avoid warning and
memory leak.
Commit 815f0ddb346c ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive") neglected to copy barrier_data() from
compiler-gcc.h into compiler-clang.h.
The definition in compiler-gcc.h was really to work around clang's more
aggressive optimization, so this broke barrier_data() on clang, and
consequently memzero_explicit() as well.
For example, this results in at least the memzero_explicit() call in
lib/crypto/sha256.c:sha256_transform() being optimized away by clang.
Fix this by moving the definition of barrier_data() into compiler.h.
Also move the gcc/clang definition of barrier() into compiler.h,
__memory_barrier() is icc-specific (and barrier() is already defined
using it in compiler-intel.h) and doesn't belong in compiler.h.
[rdunlap@infradead.org: fix ALPHA builds when SMP is not enabled]
Link: https://lkml.kernel.org/r/20201101231835.4589-1-rdunlap@infradead.org Fixes: 815f0ddb346c ("include/linux/compiler*.h: make compiler-*.h mutually exclusive") Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20201014212631.207844-1-nivedita@alum.mit.edu Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[nd: backport to account for missing
commit e506ea451254a ("compiler.h: Split {READ,WRITE}_ONCE definitions out into rwonce.h")
commit d08b9f0ca6605 ("scs: Add support for Clang's Shadow Call Stack (SCS)")
commit a3f8a30f3f00 ("Compiler Attributes: use feature checks instead of version checks")] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prarit reported that depending on the affinity setting the
' irq $N: Affinity broken due to vector space exhaustion.'
message is showing up in dmesg, but the vector space on the CPUs in the
affinity mask is definitely not exhausted.
Shung-Hsi provided traces and analysis which pinpoints the problem:
The ordering of trying to assign an interrupt vector in
assign_irq_vector_any_locked() is simply wrong if the interrupt data has a
valid node assigned. It does:
1) Try the intersection of affinity mask and node mask
2) Try the node mask
3) Try the full affinity mask
4) Try the full online mask
Obviously #2 and #3 are in the wrong order as the requested affinity
mask has to take precedence.
In the observed cases #1 failed because the affinity mask did not contain
CPUs from node 0. That made it allocate a vector from node 0, thereby
breaking affinity and emitting the misleading message.
Revert the order of #2 and #3 so the full affinity mask without the node
intersection is tried before actually affinity is broken.
If no node is assigned then only the full affinity mask and if that fails
the full online mask is tried.
sync_core_before_usermode() had an incorrect optimization. If the kernel
returns from an interrupt, it can get to usermode without IRET. It just has
to schedule to a different task in the same mm and do SYSRET. Fortunately,
there were no callers of sync_core_before_usermode() that could have had
in_irq() or in_nmi() equal to true, because it's only ever called from the
scheduler.
While at it, clarify a related comment.
Fixes: 70216e18e519 ("membarrier: Provide core serializing command, *_SYNC_CORE") Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/5afc7632be1422f91eaf7611aaaa1b5b8580a086.1607058304.git.luto@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PAT bit is in different locations for 4k and 2M/1G page table
entries.
Add a definition for _PAGE_LARGE_CACHE_MASK to represent the three
caching bits (PWT, PCD, PAT), similar to _PAGE_CACHE_MASK for 4k pages,
and use it in the definition of PMD_FLAGS_DEC_WP to get the correct PAT
index for write-protected pages.
Fixes: 6ebcb060713f ("x86/mm: Add support to encrypt the kernel in-place") Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20201111160946.147341-1-nivedita@alum.mit.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My patch caused kernel Oopses and delays in boot. Revert it.
The problem was that I moved the "mem->dma = paddr;" before the call to
be_fill_queue(). But the first thing that the be_fill_queue() function
does is memset the whole struct to zero which overwrites the assignment.
Link: https://lore.kernel.org/r/X8jXkt6eThjyVP1v@mwanda Fixes: 38b2db564d9a ("scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()") Cc: stable <stable@vger.kernel.org> Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
genksyms does not know or care about the _Static_assert() built-in, and
sometimes falls back to ignoring the later symbols, which causes
undefined behavior such as
WARNING: modpost: EXPORT symbol "ethtool_set_ethtool_phy_ops" [vmlinux] version generation failed, symbol will not be versioned.
ld: net/ethtool/common.o: relocation R_AARCH64_ABS32 against `__crc_ethtool_set_ethtool_phy_ops' can not be used when making a shared object
net/ethtool/common.o:(_ftrace_annotated_branch+0x0): dangerous relocation: unsupported relocation
Redefine static_assert for genksyms to avoid that.
The CMD13 polling is needed for commands with R1B responses. In commit a0d4c7eb71dd ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B
response"), the intent was to introduce this for requests targeted to the
RPMB partition. However, the condition to trigger the polling loop became
wrong, leading to unnecessary polling. Let's fix the condition to avoid
this.
Fixes: a0d4c7eb71dd ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response") Cc: stable@vger.kernel.org Reported-by: Zhan Liu <zliua@micron.com> Signed-off-by: Zhan Liu <zliua@micron.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Link: https://lore.kernel.org/r/20201202202320.22165-1-huobean@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Debounce filter setting should be independent from IRQ type setting
because according to the ACPI specs, there are separate arguments for
specifying debounce timeout and IRQ type in GpioIo() and GpioInt().
Together with commit 06abe8291bc31839950f7d0362d9979edc88a666
("pinctrl: amd: fix incorrect way to disable debounce filter") and
Andy's patch "gpiolib: acpi: Take into account debounce settings" [1],
this will fix broken touchpads for laptops whose BIOS set the
debounce timeout to a relatively large value. For example, the BIOS
of Lenovo AMD gaming laptops including Legion-5 15ARH05 (R7000),
Legion-5P (R7000P) and IdeaPad Gaming 3 15ARH05, set the debounce
timeout to 124.8ms. This led to the kernel receiving only ~7 HID
reports per second from the Synaptics touchpad
(MSFT0001:00 06CB:7F28).
Existing touchpads like [2][3] are not troubled by this bug because
the debounce timeout has been set to 0 by the BIOS before enabling
the debounce filter in setting IRQ type.
[1] https://lore.kernel.org/linux-gpio/20201111222008.39993-11-andriy.shevchenko@linux.intel.com/ 8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings")
[2] https://github.com/Syniurge/i2c-amd-mp2/issues/11#issuecomment-721331582
[3] https://forum.manjaro.org/t/random-short-touchpad-freezes/30832/28
The touchpad operates in Basic Mode by default in the Acer BIOS
setup, but some Aspire/TravelMate models require the i8042 to be
reset in order to be correctly detected.
We need to make sure we are not stomping on the control URB that was
issued when opening the device when attempting to toggle buzzer.
To do that we need to mark it as pending in cm109_open().
The Pavilion 13 x360 PC has a chassis-type which does not indicate it is
a convertible, while it is actually a convertible. Add it to the
dmi_switches_allow_list.
The Thinkpad Yoga 11e 4th gen with the N3450 / Celeron CPU only has
one battery which is named BAT1 instead of the expected BAT0, add a
quirk for this. This fixes not being able to set the charging tresholds
on this model; and this alsoe fixes the following errors in dmesg:
ACPI: \_SB_.PCI0.LPCB.EC__.HKEY: BCTG evaluated but flagged as error
thinkpad_acpi: Error probing battery 2
battery: extension failed to load: ThinkPad Battery Extension
battery: extension unregistered: ThinkPad Battery Extension
Note that the added quirk is for the "R0K" BIOS versions which are
used on the Thinkpad Yoga 11e 4th gen's with a Celeron CPU, there
is a separate "R0L" BIOS for the i3/i5 based versions. This may also
need the same quirk, but if that really is necessary is unknown.
The Yoga 11e series has 2 accelerometers described by a BOSC0200 ACPI node.
This setup relies on a Windows service which reads both accelerometers and
then calculates the angle between the 2 halves to determine laptop / tent /
tablet mode and then reports the calculated mode back to the EC by calling
special ACPI methods on the BOSC0200 node.
The bmc150 iio driver does not support this (it involves double
calculations requiring sqrt and arccos so this really needs to be done
in userspace), as a result of this on the Yoga 11e the thinkpad_acpi
code always reports SW_TABLET_MODE=0, starting with GNOME 3.38 reporting
SW_TABLET_MODE=0 causes GNOME to:
1. Not show the onscreen keyboard when a text-input field is focussed
with the touchscreen.
2. Disable accelerometer based auto display-rotation.
This makes sense when in laptop-mode but not when in tablet-mode. But
since for the Yoga 11e the thinkpad_acpi code always reports
SW_TABLET_MODE=0, GNOME does not know when the device is in tablet-mode.
Stop reporting the broken (always 0) SW_TABLET_MODE on Yoga 11e models
to fix this.
Note there are plans for userspace to support 360 degree hinges style
2-in-1s with 2 accelerometers and figure out the mode by itself, see:
https://gitlab.freedesktop.org/hadess/iio-sensor-proxy/-/issues/216
The local variable 'cpumask_t mask' is in the stack memory, and its address
is assigned to 'desc->affinity' in 'irq_set_affinity_hint()'.
But the memory area where this variable is located is at risk of being
modified.
During LTP testing, the following error was generated:
Fix it by using 'cpumask_of(cpu)' to get the cpumask.
Signed-off-by: Hao Si <si.hao@zte.com.cn> Signed-off-by: Lin Chen <chen.lin5@zte.com.cn> Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On systems without HW-based collections (i.e. anything except GIC-500),
we rely on firmware to perform the ITS save/restore. This doesn't
really work, as although FW can properly save everything, it cannot
fully restore the state of the command queue (the read-side is reset
to the head of the queue). This results in the ITS consuming previously
processed commands, potentially corrupting the state.
Instead, let's always save the ITS state on suspend, disabling it in the
process, and restore the full state on resume. This saves us from broken
FW as long as it doesn't enable the ITS by itself (for which we can't do
anything).
This amounts to simply dropping the ITS_FLAGS_SAVE_SUSPEND_STATE.
If someone plays with the UFS clk scaling devfreq governor through sysfs,
ufshcd_devfreq_scale may be called even when HBA is not runtime ACTIVE.
This can lead to unexpected error. We cannot just protect it by calling
pm_runtime_get_sync() because that may cause a race condition since HBA
runtime suspend ops need to suspend clk scaling. To fix this call
pm_runtime_get_noresume() and check HBA's runtime status. Only proceed if
HBA is runtime ACTIVE, otherwise just bail.
To start stack unwinding (SP, PC and BLINK) are needed. When the
explicit execution context (pt_regs etc) is not available, unwinder
assumes the task is sleeping (in __switch_to()) and fetches SP and BLINK
from kernel mode stack.
But this assumption is not true, specially in a SMP system, when top
runs on 1 core, there may be active running processes on all cores.
So when unwinding non courrent tasks, ensure they are NOT running.
And while at it, handle the self unwinding case explicitly.
This came out of investigation of a customer reported hang with
rcutorture+top
During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx.
In case we have a FW assert right after it, it remains NULL though.
We end up running into endless loop due to mac80211 trying repeatedly to
move us to ASSOC state, and we keep returning -EINVAL. Later down the road
we hit a kernel panic.
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs
are not practical. Use newly introduced aliases for mmcblk devices from [1].
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc4781 ("spi: bcm2835aux: Fix use-after-free on unbind") Link: https://github.com/ClangBuiltLinux/linux/issues/1199 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
[lukas: backport to 4.19-stable, add stable designation] Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: <stable@vger.kernel.org> # v4.4+: e13ee6cc4781: spi: bcm2835aux: Fix use-after-free on unbind Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcm2835aux_spi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
393f203f5fd5 ("x86_64: kasan: add interceptors for memset/memmove/memcpy functions")
added .weak directives to arch/x86/lib/mem*_64.S instead of changing the
existing ENTRY macros to WEAK. This can lead to the assembly snippet
.weak memcpy
...
.globl memcpy
which will produce a STB_WEAK memcpy with GNU as but STB_GLOBAL memcpy
with LLVM's integrated assembler before LLVM 12. LLVM 12 (since
https://reviews.llvm.org/D90108) will error on such an overridden symbol
binding.
Commit
ef1e03152cb0 ("x86/asm: Make some functions local")
changed ENTRY in arch/x86/lib/memcpy_64.S to SYM_FUNC_START_LOCAL, which
was ineffective due to the preceding .weak directive.
Use the appropriate SYM_FUNC_START_WEAK instead.
Fixes: 393f203f5fd5 ("x86_64: kasan: add interceptors for memset/memmove/memcpy functions") Fixes: ef1e03152cb0 ("x86/asm: Make some functions local") Reported-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Fangrui Song <maskray@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20201103012358.168682-1-maskray@google.com
[nd: backport due to missing
commit e9b9d020c487 ("x86/asm: Annotate aliases")
commit ffedeeb780dc ("linkage: Introduce new macros for assembler symbols")] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang's integrated assembler produces the warning for assembly files:
warning: DWARF2 only supports one section per compilation unit
If -Wa,-gdwarf-* is unspecified, then debug info is not emitted for
assembly sources (it is still emitted for C sources). This will be
re-enabled for newer DWARF versions in a follow up patch.
Enables defconfig+CONFIG_DEBUG_INFO to build cleanly with
LLVM=1 LLVM_IAS=1 for x86_64 and arm64.
This reverts commit 4179b00c04d1 ("geneve: pull IP header before ECN decapsulation").
Eric says: "network header should have been pulled already before
hitting geneve_rx()". Let's revert the syzbot fix since it's causing
more harm than good, and revisit.
There are reports wrt lockdep splat in nftables, e.g.:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 31416 at net/netfilter/nf_tables_api.c:622
lockdep_nfnl_nft_mutex_not_held+0x28/0x38 [nf_tables]
...
These are caused by an earlier, unrelated bug such as a n ABBA deadlock
in a different subsystem.
In such an event, lockdep is disabled and lockdep_is_held returns true
unconditionally. This then causes the WARN() in nf_tables.
Make the WARN conditional on lockdep still active to avoid this.
Building on arch/s390/ results in this build error:
cc1: some warnings being treated as errors
../drivers/md/dm-writecache.c: In function 'persistent_memory_claim':
../drivers/md/dm-writecache.c:323:1: error: no return statement in function returning non-void [-Werror=return-type]
Fix this by replacing the BUG() with an -EOPNOTSUPP return.
Fixes: 48debafe4f2f ("dm: add writecache target") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gfs2 tries to mount a (corrupt) file system that has no resource
groups it still tries to set preferences on the first one, which causes
a kernel null pointer dereference. This patch adds a check to function
gfs2_ri_update so this condition is detected and reported back as an
error.
Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the instances were able to use their own options, the userstacktrace
option was left hardcoded for the top level. This made the instance
userstacktrace option bascially into a nop, and will confuse users that set
it, but nothing happens (I was confused when it happened to me!)
Cc: stable@vger.kernel.org Fixes: 16270145ce6b ("tracing: Add trace options for core options to instances") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcm2835_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Moreover, since commit 0392727c261b ("spi: bcm-qspi: Handle clock probe
deferral"), bcm_qspi_probe() leaks the spi_master allocation if the call
to devm_clk_get_optional() fails.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
According to the AMD IOMMU spec, the commit 73db2fc595f3
("iommu/amd: Increase interrupt remapping table limit to 512 entries")
also requires the interrupt table length (IntTabLen) to be set to 9
(power of 2) in the device table mapping entry (DTE).
Fixes: 73db2fc595f3 ("iommu/amd: Increase interrupt remapping table limit to 512 entries") Reported-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20201207091920.3052-1-suravee.suthikulpanit@amd.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speakup exposing a line discipline allows userland to try to use it,
while it is deemed to be useless, and thus uselessly exposes potential
bugs. One of them is simply that in such a case if the line sends data,
spk_ttyio_receive_buf2 is called and crashes since spk_ttyio_synth
is NULL.
This change restricts the use of the speakup line discipline to
speakup drivers, thus avoiding such kind of issues altogether.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de> Fixes: 4b775022f6fd ("i2c: imx: add struct to hold more configurable quirks") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When investigating a slab cache bloat problem, significant amount of
negative dentry cache was seen, but confusingly they neither got shrunk
by reclaimer (the host has very tight memory) nor be shrunk by dropping
cache. The vmcore shows there are over 14M negative dentry objects on
lru, but tracing result shows they were even not scanned at all.
Further investigation shows the memcg's vfs shrinker_map bit is not set.
So the reclaimer or dropping cache just skip calling vfs shrinker. So
we have to reboot the hosts to get the memory back.
I didn't manage to come up with a reproducer in test environment, and
the problem can't be reproduced after rebooting. But it seems there is
race between shrinker map bit clear and reparenting by code inspection.
The hypothesis is elaborated as below.
The memcg hierarchy on our production environment looks like:
root
/ \
system user
The main workloads are running under user slice's children, and it
creates and removes memcg frequently. So reparenting happens very often
under user slice, but no task is under user slice directly.
So with the frequent reparenting and tight memory pressure, the below
hypothetical race condition may happen:
CPU A CPU B
reparent
dst->nr_items == 0
shrinker:
total_objects == 0
add src->nr_items to dst
set_bit
return SHRINK_EMPTY
clear_bit
child memcg offline
replace child's kmemcg_id with
parent's (in memcg_offline_kmem())
list_lru_del() between shrinker runs
see parent's kmemcg_id
dec dst->nr_items
reparent again
dst->nr_items may go negative
due to concurrent list_lru_del()
The second run of shrinker:
read nr_items without any
synchronization, so it may
see intermediate negative
nr_items then total_objects
may return 0 coincidently
keep the bit cleared
dst->nr_items != 0
skip set_bit
add scr->nr_item to dst
After this point dst->nr_item may never go zero, so reparenting will not
set shrinker_map bit anymore. And since there is no task under user
slice directly, so no new object will be added to its lru to set the
shrinker map bit either. That bit is kept cleared forever.
How does list_lru_del() race with reparenting? It is because reparenting
replaces children's kmemcg_id to parent's without protecting from
nlru->lock, so list_lru_del() may see parent's kmemcg_id but actually
deleting items from child's lru, but dec'ing parent's nr_items, so the
parent's nr_items may go negative as commit 2788cf0c401c ("memcg:
reparent list_lrus and free kmemcg_id on css offline") says.
Since it is impossible that dst->nr_items goes negative and
src->nr_items goes zero at the same time, so it seems we could set the
shrinker map bit iff src->nr_items != 0. We could synchronize
list_lru_count_one() and reparenting with nlru->lock, but it seems
checking src->nr_items in reparenting is the simplest and avoids lock
contention.
Fixes: fae91d6d8be5 ("mm/list_lru.c: set bit in memcg shrinker bitmap on first list_lru item appearance") Suggested-by: Roman Gushchin <guro@fb.com> Signed-off-by: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Roman Gushchin <guro@fb.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <stable@vger.kernel.org> [4.19] Link: https://lkml.kernel.org/r/20201202171749.264354-1-shy828301@gmail.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes sparse warnings:
drivers/md/dm.c:508:12: warning: context imbalance in 'dm_prepare_ioctl' - wrong count at exit
drivers/md/dm.c:543:13: warning: context imbalance in 'dm_unprepare_ioctl' - wrong count at exit
Fixes: 971888c46993f ("dm: hold DM table for duration of ioctl rather than use blkdev_get") Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c1a6c5ac4278 ("scsi: mpt3sas: For NVME device, issue a protocol
level reset") modified the ioctl path 'timeout' variable type to u8 from
unsigned long, limiting the maximum timeout value that the driver can
support to 255 seconds.
If the management application is requesting a higher value the resulting
timeout will be zero. The operation times out immediately and the ioctl
request fails.
Change datatype back to unsigned long.
Link: https://lore.kernel.org/r/20201125094838.4340-1-suganath-prabu.subramani@broadcom.com Fixes: c1a6c5ac4278 ("scsi: mpt3sas: For NVME device, issue a protocol level reset") Cc: <stable@vger.kernel.org> #v4.18+ Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy(). Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
thread 2 (workqueue)
--------
apic_timer_interrupt()
smp_apic_timer_interrupt()
irq_exit()
__do_softirq()
run_timer_softirq()
call_timer_fn()
cifs_echo_request() <- use-after-free in server ptr
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
projects / users / dwmw2 / linux.git / log