These particular errors can be encountered while trying to kexec when
secureboot lockdown is in place. Without this change, even with a
signed debug build, one still needs to reboot the machine to add the
appropriate dyndbg parameters (since lockdown blocks debugfs).
Accordingly, upgrade all pr_debug() before fatal error into pr_warn().
Signed-off-by: Robbie Harwood <rharwood@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jarkko Sakkinen <jarkko@kernel.org>
cc: Eric Biederman <ebiederm@xmission.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: keyrings@vger.kernel.org
cc: linux-crypto@vger.kernel.org
cc: kexec@lists.infradead.org Link: https://lore.kernel.org/r/20230220171254.592347-3-rharwood@redhat.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The PE Format Specification (section "The Attribute Certificate Table
(Image Only)") states that `dwLength` is to be rounded up to 8-byte
alignment when used for traversal. Therefore, the field is not required
to be an 8-byte multiple in the first place.
Accordingly, pesign has not performed this alignment since version
0.110. This causes kexec failure on pesign'd binaries with "PEFILE:
Signature wrapper len wrong". Update the comment and relax the check.
Like the Windows Lenovo Yoga Book X91F/L the Android Lenovo Yoga Book
X90F/L has a portrait 1200x1920 screen used in landscape mode,
add a quirk for this.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
The Acer Aspire 3830TG predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Another Lenovo convertable which reports a landscape resolution of
1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer
has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After issuing all the messages we can disable the TX_EMPTY interrupts
to avoid handling redundant interrupts. For doing a sinlge bus
detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before
~12000 after ~400).
Signed-off-by: Sheng Feng <fengsheng5@huawei.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/wireless/marvell/mwifiex/sdio.c:498:34: error: ‘mwifiex_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=]
drivers/net/wireless/marvell/mwifiex/pcie.c:175:34: error: ‘mwifiex_pcie_of_match_table’ defined but not used [-Werror=unused-const-variable=]
The commit 11e456cae91e ("selftests/bpf: Fix compilation errors: Assign a value to a constant")
fixed the issue cleanly in bpf-next.
This is an alternative fix in bpf tree to avoid merge conflict between bpf and bpf-next.
This doesn't need to be printed every second as an error:
...
<3>[17438.628385] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17439.634176] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17440.640298] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
...
Reduce priority from ERROR to DEBUG.
Signed-off-by: Grant Grundler <grundler@chromium.org> Reviewed-by: Guenter Roeck <groeck@chromium.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The tmp is defined as u32 type, which results in invalid processing of
tmp<0 in function rk817_read_or_set_full_charge_on_boot(). Therefore,
drop the comparison.
drivers/power/supply/rk817_charger.c:828 rk817_read_or_set_full_charge_on_boot() warn: unsigned 'tmp' is never less than zero.
drivers/power/supply/rk817_charger.c:788 rk817_read_or_set_full_charge_on_boot() warn: unsigned 'tmp' is never less than zero.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3444 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Tested-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
__copy_to_user_memcpy() and __clear_user_memset() had been calling
memcpy() and memset() respectively, leading to false-positive KASAN
reports when starting userspace:
[ 10.707901] Run /init as init process
[ 10.731892] process '/bin/busybox' started with executable stack
[ 10.745234] ==================================================================
[ 10.745796] BUG: KASAN: user-memory-access in __clear_user_memset+0x258/0x3ac
[ 10.747260] Write of size 2687 at addr 000de581 by task init/1
Use __memcpy() and __memset() instead to allow userspace access, which
is of course the intent of these functions.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 1effe8ca4e34 ("skbuff: fix coalescing for page_pool fragment
recycling") allowed coalescing to proceed with non page pool page and page
pool page when @from is cloned, i.e.
However, it actually requires skb_cloned(@from) to hold true until
coalescing finishes in this situation. If the other cloned SKB is
released while the merging is in process, from_shinfo->nr_frags will be
set to 0 toward the end of the function, causing the increment of frag
page _refcount to be unexpectedly skipped resulting in inconsistent
reference counts. Later when SKB(@to) is released, it frees the page
directly even though the page pool page is still in use, leading to
use-after-free or double-free errors. So it should be prohibited.
For quite some time we were chasing a bug which looked like a sudden
permanent failure of networking and mmc on some of our devices.
The bug was very sensitive to any software changes and even more to
any kernel debug options.
Finally we got a setup where the problem was reproducible with
CONFIG_DMA_API_DEBUG=y and it revealed the issue with the rx dma:
Lars was fast to find an explanation: according to the datasheet
bit 2 of the rx buffer descriptor entry has a different meaning in the
extended mode:
Address [2] of beginning of buffer, or
in extended buffer descriptor mode (DMA configuration register [28] = 1),
indicates a valid timestamp in the buffer descriptor entry.
The macb driver didn't mask this bit while getting an address and it
eventually caused a memory corruption and a dma failure.
The problem is resolved by explicitly clearing the problematic bit
if hw timestamping is used.
Fixes: 7b4296148066 ("net: macb: Add support for PTP timestamps in DMA descriptors") Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev> Co-developed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230412232144.770336-1-roman.gushchin@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
lena wang reported an issue caused by udpv6_sendmsg()
mangling msg->msg_name and msg->msg_namelen, which
are later read from ____sys_sendmsg() :
/*
* If this is sendmmsg() and sending to current destination address was
* successful, remember it.
*/
if (used_address && err >= 0) {
used_address->name_len = msg_sys->msg_namelen;
if (msg_sys->msg_name)
memcpy(&used_address->name, msg_sys->msg_name,
used_address->name_len);
}
udpv6_sendmsg() wants to pretend the remote address family
is AF_INET in order to call udp_sendmsg().
A fix would be to modify the address in-place, instead
of using a local variable, but this could have other side effects.
Instead, restore initial values before we return from udpv6_sendmsg().
Fixes: c71d8ebe7a44 ("net: Fix security_socket_sendmsg() bypass problem.") Reported-by: lena wang <lena.wang@mediatek.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Maciej Żenczykowski <maze@google.com> Link: https://lore.kernel.org/r/20230412130308.1202254-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The netlink message for creating a new datapath takes an array
of ports for the PID creation. This shouldn't cause much issue
but correct it for future cases where we need to do decode of
datapath information that could include the per-cpu PID map.
Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.
This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip.
It is because that skb->len requires at least sizeof(struct qrtr_ctrl_pkt)
in qrtr_tx_resume(). And skb->len equals to size in qrtr_endpoint_post().
But size is less than sizeof(struct qrtr_ctrl_pkt) when qrtr_cb->type
equals to QRTR_TYPE_RESUME_TX in qrtr_endpoint_post() under the syzbot
scenario. This triggers the uninit variable access bug.
Add size check when qrtr_cb->type equals to QRTR_TYPE_RESUME_TX in
qrtr_endpoint_post() to fix the bug.
syzbot is reporting circular locking dependency between cpu_hotplug_lock
and freezer_mutex, for commit f5d39b020809 ("freezer,sched: Rewrite core
freezer logic") replaced atomic_inc() in freezer_apply_state() with
static_branch_inc() which holds cpu_hotplug_lock.
When dma_set_mask fails it directly returns without disabling pci
device and freeing ipc_pcie. Fix this my calling a correct goto label
As dma_set_mask returns either 0 or -EIO, we can use a goto label, as
it finally returns -EIO.
Add a set_mask_fail goto label which stands consistent with other goto
labels in this function..
Fixes: 035e3befc191 ("net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled") Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism") Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
hci_connect_le_scan_cleanup shall always be invoked to cleanup the
states and re-enable passive scanning if necessary, otherwise it may
cause the pending action to stay active causing multiple attempts to
connect.
Fixes: 9b3628d79b46 ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
assume the following setup on a single machine:
1. An openvswitch instance with one bridge and default flows
2. two network namespaces "server" and "client"
3. two ovs interfaces "server" and "client" on the bridge
4. for each ovs interface a veth pair with a matching name and 32 rx and
tx queues
5. move the ends of the veth pairs to the respective network namespaces
6. assign ip addresses to each of the veth ends in the namespaces (needs
to be the same subnet)
7. start some http server on the server network namespace
8. test if a client in the client namespace can reach the http server
when following the actions below the host has a chance of getting a cpu
stuck in a infinite loop:
1. send a large amount of parallel requests to the http server (around
3000 curls should work)
2. in parallel delete the network namespace (do not delete interfaces or
stop the server, just kill the namespace)
there is a low chance that this will cause the below kernel cpu stuck
message. If this does not happen just retry.
Below there is also the output of bpftrace for the functions mentioned
in the output.
The series of events happening here is:
1. the network namespace is deleted calling
`unregister_netdevice_many_notify` somewhere in the process
2. this sets first `NETREG_UNREGISTERING` on both ends of the veth and
then runs `synchronize_net`
3. it then calls `call_netdevice_notifiers` with `NETDEV_UNREGISTER`
4. this is then handled by `dp_device_event` which calls
`ovs_netdev_detach_dev` (if a vport is found, which is the case for
the veth interface attached to ovs)
5. this removes the rx_handlers of the device but does not prevent
packages to be sent to the device
6. `dp_device_event` then queues the vport deletion to work in
background as a ovs_lock is needed that we do not hold in the
unregistration path
7. `unregister_netdevice_many_notify` continues to call
`netdev_unregister_kobject` which sets `real_num_tx_queues` to 0
8. port deletion continues (but details are not relevant for this issue)
9. at some future point the background task deletes the vport
If after 7. but before 9. a packet is send to the ovs vport (which is
not deleted at this point in time) which forwards it to the
`dev_queue_xmit` flow even though the device is unregistering.
In `skb_tx_hash` (which is called in the `dev_queue_xmit`) path there is
a while loop (if the packet has a rx_queue recorded) that is infinite if
`dev->real_num_tx_queues` is zero.
To prevent this from happening we update `do_output` to handle devices
without carrier the same as if the device is not found (which would
be the code path after 9. is done).
Additionally we now produce a warning in `skb_tx_hash` if we will hit
the infinite loop.
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When arp_validate is set to 2, 3, or 6, validation is performed for
backup slaves as well. As stated in the bond documentation, validation
involves checking the broadcast ARP request sent out via the active
slave. This helps determine which slaves are more likely to function in
the event of an active slave failure.
However, when the target is an IPv6 address, the NS message sent from
the active interface is not checked on backup slaves. Additionally,
based on the bond_arp_rcv() rule b, we must reverse the saddr and daddr
when checking the NS message.
Note that when checking the NS message, the destination address is a
multicast address. Therefore, we must convert the target address to
solicited multicast in the bond_get_targets_ip6() function.
Prior to the fix, the backup slaves had a mii status of "down", but
after the fix, all of the slaves' mii status was updated to "UP".
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets") Reviewed-by: Jonathan Toppins <jtoppins@redhat.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
UBSAN: shift-out-of-bounds in net/ipv4/tcp_input.c:555:23
shift exponent 255 is too large for 32-bit type 'int'
CPU: 1 PID: 7907 Comm: ssh Not tainted 6.3.0-rc4-00161-g62bad54b26db-dirty #206
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x136/0x150
__ubsan_handle_shift_out_of_bounds+0x21f/0x5a0
tcp_init_transfer.cold+0x3a/0xb9
tcp_finish_connect+0x1d0/0x620
tcp_rcv_state_process+0xd78/0x4d60
tcp_v4_do_rcv+0x33d/0x9d0
__release_sock+0x133/0x3b0
release_sock+0x58/0x1b0
'maxwin' is int, shifting int for 32 or more bits is undefined behaviour.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.
Fix this by changing direct return to a goto 'out_err'.
Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.") Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing pKVM code attempts to advertise CSV2/3 using values
initialized to 0, but never set. To advertise CSV2/3 to protected
guests, pass the CSV2/3 values to hyp when initializing hyp's
view of guests' ID_AA64PFR0_EL1.
Similar to non-protected KVM, these are system-wide, rather than
per cpu, for simplicity.
Fixes: 6c30bfb18d0b ("KVM: arm64: Add handlers for protected VM System Registers") Signed-off-by: Fuad Tabba <tabba@google.com> Link: https://lore.kernel.org/r/20230404152321.413064-1-tabba@google.com Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nVHE object at EL2 maintains its own copies of some host variables
so that, when pKVM is enabled, the host cannot directly modify the
hypervisor state. When running in normal nVHE mode, however, these
variables are still mirrored at EL2 but are not initialised.
Initialise the hypervisor symbols from the host copies regardless of
pKVM, ensuring that any reference to this data at EL2 with normal nVHE
will return a sensibly initialised value.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Tested-by: Vincent Donnefort <vdonnefort@google.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221110190259.26861-16-will@kernel.org
Stable-dep-of: e81625218bf7 ("KVM: arm64: Advertise ID_AA64PFR0_EL1.CSV2/3 to protected VMs") Signed-off-by: Sasha Levin <sashal@kernel.org>
When BPF_TRAMP_F_CALL_ORIG is set, BPF trampoline uses BLR to jump
back to the instruction next to call site to call the patched function.
For BTI-enabled kernel, the instruction next to call site is usually
PACIASP, in this case, it's safe to jump back with BLR. But when
the call site is not followed by a PACIASP or bti, a BTI exception
is triggered.
And the instruction next to call site of bpf_fentry_test1 is ADD,
not PACIASP:
<bpf_fentry_test1>:
bti c
nop
nop
add w0, w0, #0x1
paciasp
For BPF prog, JIT always puts a PACIASP after call site for BTI-enabled
kernel, so there is no problem. To fix it, replace BLR with RET to bypass
the branch target check.
Fixes: 71ebd71921e4 ("xen/9pfs: connect to the backend") Signed-off-by: Zheng Wang <zyytlz.wz@163.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In terminate_all we should queue up all submitted descriptors to be
freed. We do that for the content of the 'issued' and 'submitted' lists,
but the 'current_tx' descriptor falls through the cracks as it's
removed from the 'issued' list once it gets assigned to be the current
descriptor. Explicitly queue up freeing of the 'current_tx' descriptor
to address a memory leak that is otherwise present.
In addition to TX channel and RX channel interrupt flags there's
another class of 'global' interrupt flags with unknown semantics. Those
weren't being handled up to now, and they are the suspected cause of
stuck IRQ states that have been sporadically occurring. Check the global
flags and clear them if raised.
Just skip the opcode(BPF_ST | BPF_NOSPEC) in the BPF JIT instead of
failing to JIT the entire program, given LoongArch currently has no
couterpart of a speculation barrier instruction. To verify the issue,
use the ltp testcase as shown below.
Also, Wang says:
I can confirm there's currently no speculation barrier equivalent
on LonogArch. (Loongson says there are builtin mitigations for
Spectre-V1 and V2 on their chips, and AFAIK efforts to port the
exploits to mips/LoongArch have all failed a few years ago.)
While reviewing the udp-iter batching patches, noticed the bpf_iter_tcp
calling sock_put() is incorrect. It should call sock_gen_put instead
because bpf_iter_tcp is iterating the ehash table which has the req sk
and tw sk. This patch replaces all sock_put with sock_gen_put in the
bpf_iter_tcp codepath.
Fixes: 04c7820b776f ("bpf: tcp: Bpf iter batching and lock_sock") Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20230328004232.2134233-1-martin.lau@linux.dev Signed-off-by: Sasha Levin <sashal@kernel.org>
As for multicast:
- The SIDR is the only mode that makes sense;
- Besides PS_UDP, other port spaces like PS_IB is also allowed, as it is
UD compatible. In this case qkey also needs to be set [1].
This patch allows only UD qp_type to join multicast, and set qkey to
default if it's not set, to fix an uninit-value error: the ib->rec.qkey
field is accessed without being initialized.
Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join") Reported-by: syzbot+8fcbb77276d43cc8b693@syzkaller.appspotmail.com Signed-off-by: Mark Zhang <markzhang@nvidia.com> Link: https://lore.kernel.org/r/58a4a98323b5e6b1282e83f6b76960d06e43b9fa.1679309909.git.leon@kernel.org Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disabling the cache in commit 2ff4ba9e3702 ("clk: rs9: Fix I2C accessors")
without removing cache synchronization in resume path results in a
kernel panic as map->cache_ops is unset, due to REGCACHE_NONE.
Enable flat cache again to support resume again. num_reg_defaults_raw
is necessary to read the cache defaults from hardware. Some registers
are strapped in hardware and cannot be provided in software.
The max inline mtt count supported is ERDMA_MAX_INLINE_MTT_ENTRIES.
When mr->mem.mtt_nents == ERDMA_MAX_INLINE_MTT_ENTRIES, inline mtt
is also supported, fix it.
Max EQ depth of hardware is 32K, the current default EQ depth is too small
for some applications, so change the default depth to 4096.
Max send WRs the hardware can support is 8K, but the driver limits the
value to 4K. Remove this limitation.
Fixes: be3cff0f242d ("RDMA/erdma: Add the hardware related definitions") Fixes: db23ae64caac ("RDMA/erdma: Add verbs header file") Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com> Link: https://lore.kernel.org/r/20230320084652.16807-3-chengyou@linux.alibaba.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when driver queries PTYS to report which link speed is being
used on its RoCE ports, it does not check the case of having 400Gbps
transmitted over 8 lanes. Thus it fails to report the said speed and
instead it defaults to report 10G over 4 lanes.
Add a check for the said speed when querying PTYS and report it back
correctly when needed.
Fixes: 08e8676f1607 ("IB/mlx5: Add support for 50Gbps per lane link modes") Signed-off-by: Maher Sanalla <msanalla@nvidia.com> Reviewed-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/ec9040548d119d22557d6a4b4070d6f421701fd4.1678973994.git.leon@kernel.org Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add ipv4 check to irdma_find_listener(). Otherwise the function
incorrectly finds and returns a listener with a different addr family for
the zero IP addr, if a listener with a zero IP addr and the same port as
the one searched for has already been created.
When running perftest with large number of connections in iWARP mode, the
passive side could be slow to respond. Increase the rexmit counter default
to allow scaling connections.
On rmmod of irdma, the PBLE object memory is not being freed. PBLE object
memory are not statically pre-allocated at function initialization time
unlike other HMC objects. PBLEs objects and the Segment Descriptors (SD)
for it can be dynamically allocated during scale up and SD's remain
allocated till function deinitialization.
Fix this leak by adding IRDMA_HMC_IW_PBLE to the iw_hmc_obj_types[] table
and skip pbles in irdma_create_hmc_obj but not in irdma_del_hmc_objects().
Currently, artificial SW completions are generated for NOP wqes which can
generate unexpected completions with wr_id = 0. Skip the generation of
artificial completions for NOPs.
Fixes: 81091d7696ae ("RDMA/irdma: Add SW mechanism to generate completions on error") Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Link: https://lore.kernel.org/r/20230315145231.931-2-shiraz.saleem@intel.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In sprd clock driver, regmap_config.max_register was set to a fixed value
which is likely larger than the address range configured in device tree,
when reading registers through debugfs it would cause access violation.
On TGL+ the DSS control registers are at different offsets, and there's
one per pipe. Fix the offsets to fix dual link DSI for TGL+.
There would be helpers for this in the DSC code, but just do the quick
fix now for DSI. Long term, we should probably move all the DSS handling
into intel_vdsc.c, so exporting the helpers seems counter-productive.
I got really badly confused in d443d9386472 ("fbcon: move more common
code into fb_open()") because we set the con2fb_map before the failure
points, which didn't look good.
But in trying to fix that I moved the assignment into the wrong path -
we need to do it for _all_ vc we take over, not just the first one
(which additionally requires the call to con2fb_acquire_newinfo).
I've figured this out because of a KASAN bug report, where the
fbcon_registered_fb and fbcon_display arrays went out of sync in
fbcon_mode_deleted() because the con2fb_map pointed at the old
fb_info, but the modes and everything was updated for the new one.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Helge Deller <deller@gmx.de> Tested-by: Xingyuan Mo <hdthky0@gmail.com> Fixes: d443d9386472 ("fbcon: move more common code into fb_open()") Reported-by: Xingyuan Mo <hdthky0@gmail.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Xingyuan Mo <hdthky0@gmail.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v5.19+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a regressoin introduced in b07db3958485 ("fbcon: Ditch error
handling for con2fb_release_oldinfo"). I failed to realize what the if
(!err) checks. The mentioned commit was dropping the
con2fb_release_oldinfo() return value but the if (!err) was also
checking whether the con2fb_acquire_newinfo() function call above
failed or not.
Fix this with an early return statement.
Note that there's still a difference compared to the orginal state of
the code, the below lines are now also skipped on error:
if (!search_fb_in_map(info_idx))
info_idx = newidx;
These are only needed when we've actually thrown out an old fb_info
from the console mappings, which only happens later on.
Also move the fbcon_add_cursor_work() call into the same if block,
it's all protected by console_lock so doesn't matter when we set up
the blinking cursor delayed work anyway. This further simplifies the
control flow and allows us to ditch the found local variable.
v2: Clarify commit message (Javier)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Helge Deller <deller@gmx.de> Tested-by: Xingyuan Mo <hdthky0@gmail.com> Fixes: b07db3958485 ("fbcon: Ditch error handling for con2fb_release_oldinfo") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Xingyuan Mo <hdthky0@gmail.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v5.19+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, with VHE, KVM enables the EL0 event counting for the
guest on vcpu_load() or KVM enables it as a part of the PMU
register emulation process, when needed. However, in the migration
case (with VHE), the same handling is lacking, as vPMU register
values that were restored by userspace haven't been propagated yet
(the PMU events haven't been created) at the vcpu load-time on the
first KVM_RUN (kvm_vcpu_pmu_restore_guest() called from vcpu_load()
on the first KVM_RUN won't do anything as events_{guest,host} of
kvm_pmu_events are still zero).
So, with VHE, enable the guest's EL0 event counting on the first
KVM_RUN (after the migration) when needed. More specifically,
have kvm_pmu_handle_pmcr() call kvm_vcpu_pmu_restore_guest()
so that kvm_pmu_handle_pmcr() on the first KVM_RUN can take
care of it.
Fixes: d0c94c49792c ("KVM: arm64: Restore PMU configuration on first run") Cc: stable@vger.kernel.org Reviewed-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Reiji Watanabe <reijiw@google.com> Link: https://lore.kernel.org/r/20230329023944.2488484-1-reijiw@google.com Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an oversight from dc5bdb68b5b3 ("drm/fb-helper: Fix vt
restore") - I failed to realize that nasty userspace could set this.
It's not pretty to mix up kernel-internal and userspace uapi flags
like this, but since the entire fb_var_screeninfo structure is uapi
we'd need to either add a new parameter to the ->fb_set_par callback
and fb_set_par() function, which has a _lot_ of users. Or some other
fairly ugly side-channel int fb_info. Neither is a pretty prospect.
Instead just correct the issue at hand by filtering out this
kernel-internal flag in the ioctl handling code.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Fixes: dc5bdb68b5b3 ("drm/fb-helper: Fix vt restore") Cc: Alex Deucher <alexander.deucher@amd.com> Cc: shlomo@fastmail.com Cc: Michel Dänzer <michel@daenzer.net> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: dri-devel@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v5.7+ Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Qiujun Huang <hqjagain@gmail.com> Cc: Peter Rosin <peda@axentia.se> Cc: linux-fbdev@vger.kernel.org Cc: Helge Deller <deller@gmx.de> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Shigeru Yoshida <syoshida@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230404193934.472457-1-daniel.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BTRFS_FS_CSUM_IMPL_FAST flag is currently set whenever a non-generic
crc32c is detected, which is the incorrect check if the file system uses
a different checksumming algorithm. Refactor the code to only check
this if crc32c is actually used. Note that in an ideal world the
information if an algorithm is hardware accelerated or not should be
provided by the crypto API instead, but that's left for another day.
CC: stable@vger.kernel.org # 5.4.x: c8a5f8ca9a9c: btrfs: print checksum type and implementation at mount time CC: stable@vger.kernel.org # 5.4.x Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d7b9416fe5c5 ("btrfs: remove btrfs_end_io_wq") converted the read
and I/O handling from btrfs_workqueues to Linux workqueues, and as part
of that lost the code to apply the thread_pool= based max_active limit
on remount. Restore it.
Fixes: d7b9416fe5c5 ("btrfs: remove btrfs_end_io_wq") CC: stable@vger.kernel.org # 6.0+ Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
==================================================================
BUG: KASAN: slab-use-after-free in hci_conn_del+0xba/0x3a0
Write of size 8 at addr ffff88800208e9c8 by task iso-tester/31
When it happens, hci_cs_setup_sync_conn won't be able to obtain the
reference to the SCO connection, so it will be stuck and potentially
hinder subsequent connections to the same device.
This patch prevents that by also deleting the SCO connection if it is
still not established when the corresponding ACL connection is deleted.
Signed-off-by: Archie Pusaka <apusaka@chromium.org> Reviewed-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an incorrect loop exit condition in code that replaces
'/' symbols in the board name. There might also be a memory corruption
issue here, but it is unlikely to be a real problem.
Cc: <stable@vger.kernel.org> Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential race condition in hidp_session_thread that may
lead to use-after-free. For instance, the timer is active while
hidp_del_timer is called in hidp_session_thread(). After hidp_session_put,
then 'session' will be freed, causing kernel panic when hidp_idle_timeout
is running.
The solution is to use del_timer_sync instead of del_timer.
Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit d0be8347c623 ("Bluetooth: L2CAP: Fix use-after-free
caused by l2cap_chan_put"), just use l2cap_chan_hold_unless_zero to
prevent referencing a channel that is about to be destroyed.
Cc: stable@kernel.org Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of keep-alive (KAE) has resulted in loss of audio on some A750/770
cards as the transition from keep-alive to stream playback is not
working as expected. As there is limited benefit of the new KAE mode
on discrete cards, revert back to older silent-stream implementation
on these systems.
The BIOS botches this one completely - it says the 2nd S/PDIF output is
used, while in fact it's the 1st one. This is tested on DP45SG, but I'm
assuming it's valid for the other boards in the series as well.
Also add some comments regarding the pins.
FWIW, the codec is apparently still sold by Tempo Semiconductor, Inc.,
where one can download the documentation.
It could have never worked, as snd_emu10k1_fx8010_playback_prepare() and
snd_emu10k1_fx8010_playback_hw_free() assume the emu10k1 offset for the
ETRAM, and the default DSP code includes no handler for it. It also
wouldn't make a lot of sense to make it work, as Audigy has an own, much
simpler, pass-through mechanism. So just skip creation of the device.
The direct return will cause the stream list of "&tscm->domain" unemptied
and the session in "tscm" unfinished if amdtp_domain_start() returns with
an error.
Fix this by changing the direct return to a goto which will empty the
stream list of "&tscm->domain" and finish the session in "tscm".
The snd_tscm_stream_start_duplex() function is called in the prepare
callback of PCM. According to "ALSA Kernel API Documentation", the prepare
callback of PCM will be called many times at each setup. So, if the
"&d->streams" list is not emptied, when the prepare callback is called
next time, snd_tscm_stream_start_duplex() will receive -EBUSY from
amdtp_domain_add_stream() that tries to add an existing stream to the
domain. The error handling code after the "error" label will be executed
in this case, and the "&d->streams" list will be emptied. So not emptying
the "&d->streams" list will not cause an issue. But it is more efficient
and readable to empty it on the first error by changing the direct return
to a goto statement.
The session in "tscm" has been begun before amdtp_domain_start(), so it
needs to be finished when amdtp_domain_start() fails.
Add pins and verbs needed to enable speakers and jack.
The pins and verbs configurations were identified by snooping the
Windows driver commands, with a nice write-up here:
https://brakkee.org/site/2023/02/07/fixing-sound-on-the-asus-n7601zm/
Due to two copy/pastos, closing the MIC or EFX capture device would
make a running ADC capture hang due to unsetting its interrupt handler.
In principle, this would have also allowed dereferencing dangling
pointers, but we're actually rather thorough at disabling and flushing
the ints.
While it may sound like one, this actually wasn't a hypothetical bug:
PortAudio will open a capture stream at startup (and close it right
away) even if not asked to. If the first device is busy, it will just
proceed with the next one ... thus killing a concurrent capture.
[Why & How]
drm_dp_remove_payload() interface was changed. Correct amdgpu dm code
to pass the right parameter to the drm helper function.
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry-picked from b8ca445f550a9a079134f836466ddda3bfad6108)
[Hand modified due to missing f0127cb11299df80df45583b216e13f27c408545 which
failed to apply due to missing 94dfeaa46925bb6b4d43645bbb6234e846dec257] Reported-and-tested-by: Veronika Schwan <veronika@pisquaredover6.de> Fixes: d7b5638bd337 ("drm/amd/display: Take FEC Overhead into Timeslot Calculation") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a regression on Lenovo Z13, which can't wake
from the lid with it applied; and some unspecified AMD based Dell
platforms are unable to wake from hitting the power button
btf_dump_emit_struct_def attempts to print empty structures at a
single line, e.g. `struct empty {}`. However, it has to account for a
case when there are no regular but some padding fields in the struct.
In such case `vlen` would be zero, but size would be non-zero.
E.g. here is struct bpf_timer from vmlinux.h before this patch:
The maple tree tracks the stack and is able to update the pivot
(lower/upper boundary) in-place to allow the page fault handler to write
to the tree while holding just the mmap read lock. This is safe as the
writes to the stack have a guard VMA which ensures there will always be
a NULL in the direction of the growth and thus will only update a pivot.
It is possible, but not recommended, to have VMAs that grow up/down
without guard VMAs. syzbot has constructed a testcase which sets up a
VMA to grow and consume the empty space. Overwriting the entire NULL
entry causes the tree to be altered in a way that is not safe for
concurrent readers; the readers may see a node being rewritten or one
that does not match the maple state they are using.
Enabling RCU mode allows the concurrent readers to see a stable node and
will return the expected result.
Link: https://lkml.kernel.org/r/20230227173632.3292573-9-surenb@google.com Cc: stable@vger.kernel.org Fixes: d4af56c5c7c6 ("mm: start tracking VMAs with maple tree") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Reported-by: syzbot+8d95422d3537159ca390@syzkaller.appspotmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dereferencing RCU objects within the RCU callback without the RCU check
has caused lockdep to complain. Fix the RCU dereferencing by using the
RCU callback lock to ensure the operation is safe.
Also stop creating a new lock to use for dereferencing during destruction
of the tree or subtree. Instead, pass through a pointer to the tree that
has the lock that is held for RCU dereferencing checking. It also does
not make sense to use the maple state in the freeing scenario as the tree
walk is a special case where the tree no longer has the normal encodings
and parent pointers.
Link: https://lkml.kernel.org/r/20230227173632.3292573-8-surenb@google.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Cc: stable@vger.kernel.org Reported-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an smp_rmb() before reading the parent pointer to ensure that anything
read from the node prior to the parent pointer hasn't been reordered ahead
of this check.
The is necessary for RCU mode.
Link: https://lkml.kernel.org/r/20230227173632.3292573-7-surenb@google.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Cc: stable@vger.kernel.org Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to mte_set_dead_node() before the smp_wmb() already calls
smp_wmb() so this is not needed. This is an optimization for the RCU mode
of the maple tree.
Link: https://lkml.kernel.org/r/20230227173632.3292573-5-surenb@google.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Cc: stable@vger.kernel.org Signed-off-by: Liam Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The walk to destroy the nodes was not always setting the node type and
would result in a destroy method potentially using the values as nodes.
Avoid this by setting the correct node types. This is necessary for the
RCU mode of the maple tree.
Link: https://lkml.kernel.org/r/20230227173632.3292573-4-surenb@google.com Cc: <Stable@vger.kernel.org> Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Liam Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When initially starting a search, the root node may already be in the
process of being replaced in RCU mode. Detect and restart the walk if
this is the case. This is necessary for RCU mode of the maple tree.
Link: https://lkml.kernel.org/r/20230227173632.3292573-3-surenb@google.com Cc: <Stable@vger.kernel.org> Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Liam Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If mas->node is an MAS_START, there are three cases, and they all assign
different values to mas->node and mas->offset. So there is no need to set
them to a default value before updating.
Update them directly to make them easier to understand and for better
readability.
Link: https://lkml.kernel.org/r/20221221060058.609003-7-vernon2gm@gmail.com Cc: <Stable@vger.kernel.org> Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Vernon Yang <vernon2gm@gmail.com> Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an invalidated maple state is encountered during write, reset the maple
state to MAS_START. This will result in a re-walk of the tree to the
correct location for the write.
When iterating, a user may operate on the tree and cause the maple state
to be altered and left in an unintuitive state. Detect this scenario and
correct it by setting to the limit and invalidating the state.
projects / users / jedix / linux-maple.git / log