The finalization of nilfs_segctor_thread() can race with
nilfs_segctor_kill_thread() which terminates that thread, potentially
causing a use-after-free BUG as KASAN detected.
At the end of nilfs_segctor_thread(), it assigns NULL to "sc_task" member
of "struct nilfs_sc_info" to indicate the thread has finished, and then
notifies nilfs_segctor_kill_thread() of this using waitqueue
"sc_wait_task" on the struct nilfs_sc_info.
However, here, immediately after the NULL assignment to "sc_task", it is
possible that nilfs_segctor_kill_thread() will detect it and return to
continue the deallocation, freeing the nilfs_sc_info structure before the
thread does the notification.
This fixes the issue by protecting the NULL assignment to "sc_task" and
its notification, with spinlock "sc_state_lock" of the struct
nilfs_sc_info. Since nilfs_segctor_kill_thread() does a final check to
see if "sc_task" is NULL with "sc_state_lock" locked, this can eliminate
the race.
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports") Cc: stable@vger.kernel.org Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
If a second dummy client that talks to the actual I2C address was
created in probe(), there should be a proper cleanup on driver and
device removal to avoid leakage.
So unregister the dummy client via another callback.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Suggested-by: Hans de Goede <hdegoede@redhat.com> Fixes: c1e62062ff54 ("iio: light: cm32181: Handle CM3218 ACPI devices with 2 I2C resources")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2152281 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Link: https://lore.kernel.org/r/20230223020059.2013993-1-kai.heng.feng@canonical.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For output buffers, there's no guarantee that the buffer won't be full
in the first iteration of the loop in which case we would block
independently of userspace passing O_NONBLOCK or not. Fix it by always
checking the flag before going to sleep.
While at it (and as it's a bit related), refactored the loop so that the
stop condition is 'written != n', i.e, run the loop until all data has
been copied into the IIO buffers. This makes the code a bit simpler.
If for some reason 'rb->access->write()' does not write the full
requested data and the O_NONBLOCK is set, we would return 'n' to
userspace which is not really truth. Hence, let's return the number of
bytes we effectively wrote.
The CIO-DAC series of devices only supports DAC values up to 12-bit
rather than 16-bit. Trying to write a 16-bit value results in only the
lower 12 bits affecting the DAC output which is not what the user
expects. Instead, adjust the DAC write value check to reject values
larger than 12-bit so that they fail explicitly as invalid for the user.
Fixes: 3b8df5fd526e ("iio: Add IIO support for the Measurement Computing CIO-DAC family") Cc: stable@vger.kernel.org Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Link: https://lore.kernel.org/r/20230311002248.8548-1-william.gray@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The node name can contain an address part which is unused
by the driver. Moreover, this string is propagated into
the userspace label, sysfs filenames *and breaking ABI*.
Cut the address part out before assigning the channel name.
Correct the "sub_lsb" shift for the ltc2497 and drop the sub_lsb element
which is now constant.
An earlier version of the code shifted by 14 but this was a consequence
of reading three bytes into a __be32 buffer and using be32_to_cpu(), so
eight extra bits needed to be skipped. Now we use get_unaligned_be24()
and thus the additional skip is wrong.
Fixes: 2187cfeb3626 ("drivers: iio: adc: ltc2497: LTC2499 support") Signed-off-by: Ian Ray <ian.ray@ge.com> Link: https://lore.kernel.org/r/20230127125714.44608-1-ian.ray@ge.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While determining the initial pin assignment to be sent in the configure
message, using the DP_PIN_ASSIGN_DP_ONLY_MASK mask causes the DFP_U to
send both Pin Assignment C and E when both are supported by the DFP_U and
UFP_U. The spec (Table 5-7 DFP_U Pin Assignment Selection Mandates,
VESA DisplayPort Alt Mode Standard v2.0) indicates that the DFP_U never
selects Pin Assignment E when Pin Assignment C is offered.
Update the DP_PIN_ASSIGN_DP_ONLY_MASK conditional to intially select only
Pin Assignment C if it is available.
The Silicon Labs IFS-USB-DATACABLE is used in conjunction with for example
the Quint UPSes. It is used to enable Modbus communication with the UPS to
query configuration, power and battery status.
Signed-off-by: Kees Jan Koster <kjkoster@kjkoster.org> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command allocated to set exit latency LPM values need to be freed in
case the command is never queued. This would be the case if there is no
change in exit latency values, or device is missing.
When we set the dual-role port to Host mode, we observed the following
splat:
[ 167.057718] BUG: sleeping function called from invalid context at
include/linux/sched/mm.h:229
[ 167.057872] Workqueue: events tegra_xusb_usb_phy_work
[ 167.057954] Call trace:
[ 167.057962] dump_backtrace+0x0/0x210
[ 167.057996] show_stack+0x30/0x50
[ 167.058020] dump_stack_lvl+0x64/0x84
[ 167.058065] dump_stack+0x14/0x34
[ 167.058100] __might_resched+0x144/0x180
[ 167.058140] __might_sleep+0x64/0xd0
[ 167.058171] slab_pre_alloc_hook.constprop.0+0xa8/0x110
[ 167.058202] __kmalloc_track_caller+0x74/0x2b0
[ 167.058233] kvasprintf+0xa4/0x190
[ 167.058261] kasprintf+0x58/0x90
[ 167.058285] tegra_xusb_find_port_node.isra.0+0x58/0xd0
[ 167.058334] tegra_xusb_find_port+0x38/0xa0
[ 167.058380] tegra_xusb_padctl_get_usb3_companion+0x38/0xd0
[ 167.058430] tegra_xhci_id_notify+0x8c/0x1e0
[ 167.058473] notifier_call_chain+0x88/0x100
[ 167.058506] atomic_notifier_call_chain+0x44/0x70
[ 167.058537] tegra_xusb_usb_phy_work+0x60/0xd0
[ 167.058581] process_one_work+0x1dc/0x4c0
[ 167.058618] worker_thread+0x54/0x410
[ 167.058650] kthread+0x188/0x1b0
[ 167.058672] ret_from_fork+0x10/0x20
The function tegra_xusb_padctl_get_usb3_companion eventually calls
tegra_xusb_find_port and this in turn calls kasprintf which might sleep
and so cannot be called from an atomic context.
Fix this by moving the call to tegra_xusb_padctl_get_usb3_companion to
the tegra_xhci_id_work function where it is really needed.
Gregory Price reports a WARN splat with CONFIG_DEBUG_OBJECTS=y upon CXL
probing because pci_doe_submit_task() invokes INIT_WORK() instead of
INIT_WORK_ONSTACK() for a work_struct that was allocated on the stack.
All callers of pci_doe_submit_task() allocate the work_struct on the
stack, so replace INIT_WORK() with INIT_WORK_ONSTACK() as a backportable
short-term fix.
The long-term fix implemented by a subsequent commit is to move to a
synchronous API which allocates the work_struct internally in the DOE
library.
If the length in the CDAT header is larger than the concatenation of the
header and all table entries, then the CDAT exposed to user space
contains trailing null bytes.
Not every consumer may be able to handle that. Per Postel's robustness
principle, "be liberal in what you accept" and silently reduce the
cached length to avoid exposing those null bytes.
Fixes: c97006046c79 ("cxl/port: Read CDAT table") Tested-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: stable@vger.kernel.org # v6.0+ Link: https://lore.kernel.org/r/6d98b3c7da5343172bd3ccabfabbc1f31c079d74.1678543498.git.lukas@wunner.de Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If truncated CDAT entries are received from a device, the concatenation
of those entries constitutes a corrupt CDAT, yet is happily exposed to
user space.
Avoid by verifying response lengths and erroring out if truncation is
detected.
The last CDAT entry may still be truncated despite the checks introduced
herein if the length in the CDAT header is too small. However, that is
easily detectable by user space because it reaches EOF prematurely.
A subsequent commit which rightsizes the CDAT response allocation closes
that remaining loophole.
The two lines introduced here which exceed 80 chars are shortened to
less than 80 chars by a subsequent commit which migrates to a
synchronous DOE API and replaces "t.task.rv" by "rc".
The existing acpi_cdat_header and acpi_table_cdat struct definitions
provided by ACPICA cannot be used because they do not employ __le16 or
__le32 types. I believe that cannot be changed because those types are
Linux-specific and ACPI is specified for little endian platforms only,
hence doesn't care about endianness. So duplicate the structs.
Fixes: c97006046c79 ("cxl/port: Read CDAT table") Tested-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: stable@vger.kernel.org # v6.0+ Link: https://lore.kernel.org/r/bce3aebc0e8e18a1173425a7a865b232c3912963.1678543498.git.lukas@wunner.de Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cxl_cdat_get_length() only checks whether the DOE response size is
sufficient for the Table Access response header (1 dword), but not the
succeeding CDAT header (1 dword length plus other fields).
It thus returns whatever uninitialized memory happens to be on the stack
if a truncated DOE response with only 1 dword was received. Fix it.
Fixes: c97006046c79 ("cxl/port: Read CDAT table") Reported-by: Ming Li <ming4.li@intel.com> Tested-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Ming Li <ming4.li@intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: stable@vger.kernel.org # v6.0+ Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Link: https://lore.kernel.org/r/000e69cd163461c8b1bc2cf4155b6e25402c29c7.1678543498.git.lukas@wunner.de Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CDAT exposed in sysfs differs between little endian and big endian
arches: On big endian, every 4 bytes are byte-swapped.
PCI Configuration Space is little endian (PCI r3.0 sec 6.1). Accessors
such as pci_read_config_dword() implicitly swap bytes on big endian.
That way, the macros in include/uapi/linux/pci_regs.h work regardless of
the arch's endianness. For an example of implicit byte-swapping, see
ppc4xx_pciex_read_config(), which calls in_le32(), which uses lwbrx
(Load Word Byte-Reverse Indexed).
DOE Read/Write Data Mailbox Registers are unlike other registers in
Configuration Space in that they contain or receive a 4 byte portion of
an opaque byte stream (a "Data Object" per PCIe r6.0 sec 7.9.24.5f).
They need to be copied to or from the request/response buffer verbatim.
So amend pci_doe_send_req() and pci_doe_recv_resp() to undo the implicit
byte-swapping.
The CXL_DOE_TABLE_ACCESS_* and PCI_DOE_DATA_OBJECT_DISC_* macros assume
implicit byte-swapping. Byte-swap requests after constructing them with
those macros and byte-swap responses before parsing them.
Change the request and response type to __le32 to avoid sparse warnings.
Per a request from Jonathan, replace sizeof(u32) with sizeof(__le32) for
consistency.
Fixes: c97006046c79 ("cxl/port: Read CDAT table") Tested-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Cc: stable@vger.kernel.org # v6.0+ Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/3051114102f41d19df3debbee123129118fc5e6d.1678543498.git.lukas@wunner.de Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.
We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.
Fixes: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY") Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/lkml/20230403212434.296975-1-martin.blumenstingl@googlemail.com/ Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Shahab Vahedi <shahab@synopsys.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Link: https://lore.kernel.org/r/20230406024541.3556305-1-michael.wei.hong.sit@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan reports that smatch complains about a potential uninitialized
variable being used in the compat alignment fixup code.
The logic is not wrong per se, but we do end up using an uninitialized
variable if reading the instruction that triggered the alignment fault
from user space faults, even if the fault ensures that the uninitialized
value doesn't propagate any further.
Given that we just give up and return 1 if any fault occurs when reading
the instruction, let's get rid of the 'success handling' pattern that
captures the fault in a variable and aborts later, and instead, just
return 1 immediately if any of the get_user() calls result in an
exception.
Non-GSO TCP packets whose SKBs' linear portion did not include the
entire TCP header were not populating the first Tx descriptor with
as many bytes as the vNIC expected. This change ensures that all
TCP packets populate the first descriptor with the correct number of
bytes.
syzbot reported a data-race in data-race in netlink_recvmsg() [1]
Indeed, netlink_recvmsg() can be run concurrently,
and netlink_dump() also needs protection.
[1]
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
read to 0xffff888141840b38 of 8 bytes by task 23057 on cpu 0:
netlink_recvmsg+0xea/0x730 net/netlink/af_netlink.c:1988
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg net/socket.c:1038 [inline]
__sys_recvfrom+0x1ee/0x2e0 net/socket.c:2194
__do_sys_recvfrom net/socket.c:2212 [inline]
__se_sys_recvfrom net/socket.c:2208 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2208
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffff888141840b38 of 8 bytes by task 23037 on cpu 1:
netlink_recvmsg+0x114/0x730 net/netlink/af_netlink.c:1989
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg net/socket.c:1038 [inline]
____sys_recvmsg+0x156/0x310 net/socket.c:2720
___sys_recvmsg net/socket.c:2762 [inline]
do_recvmmsg+0x2e5/0x710 net/socket.c:2856
__sys_recvmmsg net/socket.c:2935 [inline]
__do_sys_recvmmsg net/socket.c:2958 [inline]
__se_sys_recvmmsg net/socket.c:2951 [inline]
__x64_sys_recvmmsg+0xe2/0x160 net/socket.c:2951
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x0000000000000000 -> 0x0000000000001000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 23037 Comm: syz-executor.2 Not tainted 6.3.0-rc4-syzkaller-00195-g5a57b48fdfcb #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023
Fixes: 9063e21fb026 ("netlink: autosize skb lengthes") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230403214643.768555-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the number of lanes was forced and then subsequently the user
omits this parameter, the ksettings->lanes is reset. The driver
should then reset the number of lanes to the device's default
for the specified speed.
However, although the ksettings->lanes is set to 0, the mod variable
is not set to true to indicate the driver and userspace should be
notified of the changes.
The consequence is that the same ethtool operation will produce
different results based on the initial state.
If the initial state is:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 2
Duplex: Full
Auto-negotiation: on
then executing 'ethtool -s swp1 speed 50000 autoneg off' will yield:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 2
Duplex: Full
Auto-negotiation: off
While if the initial state is:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 1
Duplex: Full
Auto-negotiation: off
executing the same 'ethtool -s swp1 speed 50000 autoneg off' results in:
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 1
Duplex: Full
Auto-negotiation: off
This patch fixes this behavior. Omitting lanes will always results in
the driver choosing the default lane width for the chosen speed. In this
scenario, regardless of the initial state, the end state will be, e.g.,
$ ethtool swp1 | grep -A 3 'Speed: '
Speed: 500000Mb/s
Lanes: 2
Duplex: Full
Auto-negotiation: off
Fixes: 012ce4dd3102 ("ethtool: Extend link modes settings uAPI with lanes") Signed-off-by: Andy Roulin <aroulin@nvidia.com> Reviewed-by: Danielle Ratson <danieller@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/ac238d6b-8726-8156-3810-6471291dbc7f@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit dbca1596bbb0 ("ping: convert to RCU lookups, get rid
of rwlock"), we use RCU for ping sockets, but we should use spinlock
for /proc/net/icmp to avoid a potential NULL deref mentioned in
the previous patch.
Let's go back to using spinlock there.
Note we can convert ping sockets to use hlist instead of hlist_nulls
because we do not use SLAB_TYPESAFE_BY_RCU for ping sockets.
Fixes: dbca1596bbb0 ("ping: convert to RCU lookups, get rid of rwlock") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 0daf07e52709 ("raw: convert raw sockets to RCU"), we
use RCU and hlist_nulls_for_each_entry() to iterate over SOCK_RAW
sockets. However, we should use spinlock for slow paths to avoid
the NULL deref.
Also, SOCK_RAW does not use SLAB_TYPESAFE_BY_RCU, and the slab object
is not reused during iteration in the grace period. In fact, the
lockless readers do not check the nulls marker with get_nulls_value().
So, SOCK_RAW should use hlist instead of hlist_nulls.
Instead of adding an unnecessary barrier by sk_nulls_for_each_rcu(),
let's convert hlist_nulls to hlist and use sk_for_each_rcu() for
fast paths and sk_for_each() and spinlock for /proc/net/raw.
Reset the FDIR counters when FDIR inits. Without this patch,
when VF initializes or resets, all the FDIR counters are not
cleaned, which may cause unexpected behaviors for future FDIR
rule create (e.g., rule conflict).
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF") Signed-off-by: Junfeng Guo <junfeng.guo@intel.com> Signed-off-by: Lingyu Liu <lingyu.liu@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding a FDIR filter, if ice_vc_fdir_set_irq_ctx returns failure,
the inserted fdir entry will not be removed and if ice_vc_fdir_write_fltr
returns failure, the fdir context info for irq handler will not be cleared
which may lead to inconsistent or memory leak issue. This patch refines
failure cases to resolve this issue.
Fixes: 1f7ea1cd6a37 ("ice: Enable FDIR Configure for AVF") Signed-off-by: Simei Su <simei.su@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently callback request does not use the credential specified in
CREATE_SESSION if the security flavor for the back channel is AUTH_SYS.
Problem was discovered by pynfs 4.1 DELEG5 and DELEG7 test with error:
DELEG5 st_delegation.testCBSecParms : FAILURE
expected callback with uid, gid == 17, 19, got 0, 0
Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Fixes: 8276c902bbe9 ("SUNRPC: remove uid and gid from struct auth_cred") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the unix_gid object is rcu-freed, the group_info list that it
contains is not. Ensure that we only put the group list reference once
we are really freeing the unix_gid object.
Reported-by: Zhi Li <yieli@redhat.com> Link: https://bugzilla.redhat.com/show_bug.cgi?id=2183056 Signed-off-by: Jeff Layton <jlayton@kernel.org> Fixes: fd5d2f78261b ("SUNRPC: Make server side AUTH_UNIX use lockless lookups") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
stmmac_reinit_queues() fails to fix up the RX hash. Even if the number
of channels gets restricted, the output of `ethtool -x' indicates that
all RX queues are used:
In the am65_cpsw_nuss_probe() function's cleanup path, the call to
of_platform_device_destroy() for the common->mdio_dev device is invoked
unconditionally. It is possible that either the MDIO node is not present
in the device-tree, or the MDIO node is disabled in the device-tree. In
both these cases, the MDIO device is not created, resulting in a NULL
pointer dereference when the of_platform_device_destroy() function is
invoked on the common->mdio_dev device on the cleanup path.
Fix this by ensuring that the common->mdio_dev device exists, before
attempting to invoke of_platform_device_destroy().
Fixes: a45cfcc69a25 ("net: ethernet: ti: am65-cpsw-nuss: use of_platform_device_create() for mdio") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20230403090321.835877-1-s-vadapalli@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The interrupt enable bits might be set if we want to use the GPIO as
wakeup source. Clearing this will mean disabling of interrupts in the GPIO
banks that we may want to wakeup from.
Thus remove the line that was clearing this bit from the driver's save
context function.
On ThinkStations on retrieving the attribute value the BIOS appends the
possible values to the string.
Clean up the display in the current_value_show function so the options
part is not displayed.
Fixes: a40cd7ef22fb ("platform/x86: think-lmi: Add WMI interface support on Lenovo platforms")
Reported by Mario Limoncello <Mario.Limonciello@amd.com> Link: https://github.com/fwupd/fwupd/issues/5077#issuecomment-1488730526 Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230403013120.2105-2-mpearson-lenovo@squebb.ca Tested-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
My previous commit introduced a memory leak where the item allocated
from tlmi_setting was not freed.
This commit also renames it to avoid confusion with the similarly name
variable in the same function.
Fixes: 8a02d70679fc ("platform/x86: think-lmi: Add possible_values for ThinkStation") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Link: https://lore.kernel.org/lkml/df26ff45-8933-f2b3-25f4-6ee51ccda7d8@gmx.de/T/ Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230403013120.2105-1-mpearson-lenovo@squebb.ca Tested-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When retriving a item string with tlmi_setting(), the result has to be
freed using kfree(). In current_value_show() however, malformed
item strings are not freed, causing a memory leak.
Fix this by eliminating the early return responsible for this.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Link: https://lore.kernel.org/platform-driver-x86/01e920bc-5882-ba0c-dd15-868bf0eca0b8@alu.unizg.hr/T/#t Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Fixes: 0fdf10e5fc96 ("platform/x86: think-lmi: Split current_value to reflect only the value") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20230331213319.41040-1-W_Armin@gmx.de Tested-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is because icmp6hdr does not in skb linear region under the scenario
of SOCK_RAW socket. Access icmp6_hdr(skb)->icmp6_type directly will
trigger the uninit variable access bug.
Use a local variable icmp6_type to carry the correct value in different
scenarios.
Fixes: 14878f75abd5 ("[IPV6]: Add ICMPMsgStats MIB (RFC 4293) [rev 2]") Reported-by: syzbot+8257f4dcef79de670baf@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?id=3d605ec1d0a7f2a269a1a6936ac7f2b85975ee9c Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the remote side, when QRTR socket is removed, af_qrtr will call
qrtr_port_remove() which broadcasts the DEL_CLIENT packet to all neighbours
including local NS. NS upon receiving the DEL_CLIENT packet, will remove
the lookups associated with the node:port and broadcasts the DEL_SERVER
packet.
But on the host side, due to the arrival of the DEL_CLIENT packet, the NS
would've already deleted the server belonging to that port. So when the
remote's NS again broadcasts the DEL_SERVER for that port, it throws below
error message on the host:
"failed while handling packet from 2:-2"
So fix this error by not broadcasting the DEL_SERVER packet when the
DEL_CLIENT packet gets processed."
Fixes: 0c2204a4ad71 ("net: qrtr: Migrate nameservice to kernel from userspace") Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Ram Kumar Dharuman <quic_ramd@quicinc.com> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a corner case where the asoc out stream count may change
after wait_for_sndbuf.
When the main thread in the client starts a connection, if its out stream
count is set to N while the in stream count in the server is set to N - 2,
another thread in the client keeps sending the msgs with stream number
N - 1, and waits for sndbuf before processing INIT_ACK.
However, after processing INIT_ACK, the out stream count in the client is
shrunk to N - 2, the same to the in stream count in the server. The crash
occurs when the thread waiting for sndbuf is awake and sends the msg in a
non-existing stream(N - 1), the call trace is as below:
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family" Signed-off-by: Gustav Ekelund <gustaek@axis.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0db3dc73f7a3 ("[NETPOLL]: tx lock deadlock fix") narrowed
down the region under netif_tx_trylock() inside netpoll_send_skb().
(At that point in time netif_tx_trylock() would lock all queues of
the device.) Taking the tx lock was problematic because driver's
cleanup method may take the same lock. So the change made us hold
the xmit lock only around xmit, and expected the driver to take
care of locking within ->ndo_poll_controller().
Unfortunately this only works if netpoll isn't itself called with
the xmit lock already held. Netpoll code is careful and uses
trylock(). The drivers, however, may be using plain lock().
Printing while holding the xmit lock is going to result in rare
deadlocks.
Luckily we record the xmit lock owners, so we can scan all the queues,
the same way we scan NAPI owners. If any of the xmit locks is held
by the local CPU we better not attempt any polling.
It would be nice if we could narrow down the check to only the NAPIs
and the queue we're trying to use. I don't see a way to do that now.
Reported-by: Roman Gushchin <roman.gushchin@linux.dev> Fixes: 0db3dc73f7a3 ("[NETPOLL]: tx lock deadlock fix") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a DRM driver turns on or off the screen with the audio
capability, it notifies the ELD to HD-audio HDMI codec driver via
component ops. HDMI codec driver, in turn, attaches or detaches the
PCM stream for the given port on the fly.
The problem is that, since the recent code change, the HDMI driver
always treats the PCM stream assignment dynamically; this ended up the
confusion of the PCM device appearance. e.g. when a screen goes once
off and on again, it may appear on a different PCM device before the
screen-off. Although the application should treat such a change, it
doesn't seem working gracefully with the current pipewire (maybe
PulseAudio, too).
As a workaround, this patch changes the HDMI codec driver behavior
slightly to be more consistent. Now it remembers the previous PCM
slot for the given port and try to assign to it. That is, if a port
is re-enabled, the driver tries to use the same PCM slot that was
assigned to that port previously. If it conflicts, a new slot is
searched and used like before, instead.
Note that multiple monitor connections are the only typical case where
the PCM slot preservation is effective. As long as only a single
monitor is connected, the behavior isn't changed, and the first PCM
slot is still assigned always.
For ops with "trivial" replies, nfsd4_encode_operation will shortcut
most of the encoding work and skip to just marshalling up the status.
One of the things it skips is calling op_release. This could cause a
memory leak in the layoutget codepath if there is an error at an
inopportune time.
Have the compound processing engine always call op_release, even when
op_func sets an error in op->status. With this change, we also need
nfsd4_block_get_device_info_scsi to set the gd_device pointer to NULL
on error to avoid a double free.
Reported-by: Zhi Li <yieli@redhat.com> Link: https://bugzilla.redhat.com/show_bug.cgi?id=2181403 Fixes: 34b1744c91cc ("nfsd4: define ->op_release for compound ops") Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
OPDESC() simply indexes into nfsd4_ops[] by the op's operation
number, without range checking that value. It assumes callers are
careful to avoid calling it with an out-of-bounds opnum value.
nfsd4_decode_compound() is not so careful, and can invoke OPDESC()
with opnum set to OP_ILLEGAL, which is 10044 -- well beyond the end
of nfsd4_ops[].
Reported-by: Jeff Layton <jlayton@kernel.org> Fixes: f4f9ef4a1b0a ("nfsd4: opdesc will be useful outside nfs4proc.c") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card
unless WOWL is used"), the wifi adapter by default is turned off on suspend
and then re-probed on resume.
In at least 2 model x86/acpi tablets with brcmfmac43430a1 wifi adapters,
the newly added re-probe on resume fails like this:
brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
ieee80211 phy1: brcmf_bus_started: failed: -110
ieee80211 phy1: brcmf_attach: dongle is not responding: err=-110
brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
It seems this specific brcmfmac model does not like being reprobed without
it actually being turned off first.
And the adapter is not being turned off during suspend because of
commit f0992ace680c ("brcmfmac: prohibit ACPI power management for brcmfmac
driver").
Now that the driver is being reprobed on resume, the disabling of ACPI
pm is no longer necessary, except when WOWL is used (in which case there
is no-reprobe).
Move the dis-/en-abling of ACPI pm to brcmf_sdio_wowl_config(), this fixes
the brcmfmac43430a1 suspend/resume regression and should help save some
power when suspended.
This change means that the code now also may re-enable ACPI pm when WOWL
gets disabled. ACPI pm should only be re-enabled if it was enabled by
the ACPI core originally. Add a brcmf_sdiod_acpi_save_power_manageable()
to save the original state for this.
This has been tested on the following devices:
Asus T100TA brcmfmac43241b4-sdio
Acer Iconia One 7 B1-750 brcmfmac43340-sdio
Chuwi Hi8 brcmfmac43430a0-sdio
Chuwi Hi8 brcmfmac43430a1-sdio
(the Asus T100TA is the device for which the prohibiting of ACPI pm
was originally added)
Fixes: 92cadedd9d5f ("brcmfmac: Avoid keeping power to SDIO card unless WOWL is used") Cc: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230320122252.240070-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 65b32f801bfb ("uapi: move IPPROTO_L2TP to in.h") moved the
definition of IPPROTO_L2TP from a define to an enum, but since
__stringify doesn't work properly with enums, we ended up breaking the
modalias strings for the l2tp modules:
Moreover, fix the ordering of the parameters passed to
MODULE_ALIAS_NET_PF_PROTO_TYPE() by switching proto and type.
Fixes: 65b32f801bfb ("uapi: move IPPROTO_L2TP to in.h") Link: https://lore.kernel.org/lkml/ZCQt7hmodtUaBlCP@righiandr-XPS-13-7390 Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, intel_speed_mode_2500() will fix-up xpcs_an_inband
to 1 if the underlying controller has a max speed of 1000Mbps.
The value has been initialized and modified if it is
a fixed-linked setup earlier.
This patch removes the fix-up to allow for fixed-linked setup
support. In stmmac_phy_setup(), ovr_an_inband is set based on
the value of xpcs_an_inband. Which in turn will return an
error in phylink_parse_mode() where MLO_AN_FIXED and
ovr_an_inband are both set.
Fixes: c82386310d95 ("stmmac: intel: prepare to support 1000BASE-X phy interface setting") Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After the introduction of the fixed-link support, the MAC driver
no longer attempt to scan for a PHY to attach to. This causes the
non fixed-link setups to stop working.
Using the phylink_expects_phy() to check and determine if the MAC
should expect and attach a PHY.
Fixes: ab21cf920928 ("net: stmmac: make mdio register skips PHY scanning for fixed-link") Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: Lai Peter Jun Ann <peter.jun.ann.lai@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Provide phylink_expects_phy() to allow MAC drivers to check if it
is expecting a PHY to attach to. Since fixed-linked setups do not
need to attach to a PHY.
Provides a boolean value as to if the MAC should expect a PHY.
Returns true if a PHY is expected.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY") Signed-off-by: Sasha Levin <sashal@kernel.org>
Use qrtr_node_lock to protect qrtr_node_lookup() implementation, this
is actually improving the protection of node reference.
Fixes: 0a7e0d0ef054 ("net: qrtr: Migrate node lookup tree to spinlock") Reported-by: syzbot+a7492efaa5d61b51db23@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=a7492efaa5d61b51db23 Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To determine whether the guest has caused an external interruption loop
upon code 20 (external interrupt) intercepts, the ext_new_psw needs to
be inspected to see whether external interrupts are enabled.
Under non-PV, ext_new_psw can simply be taken from guest lowcore. Under
PV, KVM can only access the encrypted guest lowcore and hence the
ext_new_psw must not be taken from guest lowcore.
handle_external_interrupt() incorrectly did that and hence was not able
to reliably tell whether an external interruption loop is happening or
not. False negatives cause spurious failures of my kvm-unit-test
for extint loops[1] under PV.
Since code 20 is only caused under PV if and only if the guest's
ext_new_psw is enabled for external interrupts, false positive detection
of a external interruption loop can not happen.
Fix this issue by instead looking at the guest PSW in the state
description. Since the PSW swap for external interrupt is done by the
ultravisor before the intercept is caused, this reliably tells whether
the guest is enabled for external interrupts in the ext_new_psw.
Also update the comments to explain better what is happening.
The order in which clocks are stopped matters as some of the clock
like NPL are derived from MCLK.
Without this patch, Dragonboard RB5 DSP would crash with below error:
qcom_q6v5_pas 17300000.remoteproc: fatal error received:
ABT_dal.c:278:ABTimeout: AHB Bus hang is detected,
Number of bus hang detected := 2 , addr0 = 0x3370000 , addr1 = 0x0!!!
Turn off fsgen first, followed by npl and then finally mclk, which is exactly
the opposite order of enable sequence.
Fixes: 1dc3459009c3 ("ASoC: codecs: lpass: register mclk after runtime pm") Reported-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Amit Pundir <amit.pundir@linaro.org> Link: https://lore.kernel.org/r/20230323110125.23790-1-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver only supports normal polarity. Complete the implementation of
.get_state() by setting .polarity accordingly.
This fixes a regression that was possible since commit c73a3107624d
("pwm: Handle .get_state() failures") which stopped to zero-initialize
the state passed to the .get_state() callback. This was reported at
https://forum.odroid.com/viewtopic.php?f=177&t=46360 . While this was an
unintended side effect, the real issue is the driver's callback not
setting the polarity.
There is a complicating fact, that the .apply() callback fakes support
for inversed polarity. This is not (and cannot) be matched by
.get_state(). As fixing this isn't easy, only point it out in a comment
to prevent authors of other drivers from copying that approach.
Fixes: c375bcbaabdb ("pwm: meson: Read the full hardware state in meson_pwm_get_state()") Reported-by: Munehisa Kamata <kamatam@amazon.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20230310191405.2606296-1-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
The set_get_data() IPC op bypasses the check for the no_pm flag as done
with the regular IPC tx_msg op. Since set_get_data should be performed
when the DSP is in D0I0, set the DSP power state to D0I0 before sending
the IPC's in sof_ipc4_set_get_data().
Fixes: ceb89acc4dc8 ("ASoC: SOF: ipc4: Add support for mandatory message handling functionality") Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20230322085538.10214-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
relid2channel() assumes vmbus channel array to be allocated when called.
However, in cases such as kdump/kexec, not all relids will be reset by the host.
When the second kernel boots and if the guest receives a vmbus interrupt during
vmbus driver initialization before vmbus_connect() is called, before it finishes,
or if it fails, the vmbus interrupt service routine is called which in turn calls
relid2channel() and can cause a null pointer dereference.
Print a warning and error out in relid2channel() for a channel id that's invalid
in the second kernel.
Fixes: 8b6a877c060e ("Drivers: hv: vmbus: Replace the per-CPU channel lists with a global array of channels") Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Link: https://lore.kernel.org/r/20230217204411.212709-1-mgamal@redhat.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ebe363197e52 ("gpio: add a reusable generic gpio_chip using regmap") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Michael Walle <michael@walle.cc> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Bartosz Golaszewski <brgl@bgdev.pl> Cc: linux-gpio@vger.kernel.org Acked-by: Michael Walle <michael@walle.cc> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Presently, when a guest writes 1 to PMCR_EL0.{C,P}, which is WO/RAZ,
KVM saves the register value, including these bits.
When userspace reads the register using KVM_GET_ONE_REG, KVM returns
the saved register value as it is (the saved value might have these
bits set). This could result in userspace setting these bits on the
destination during migration. Consequently, KVM may end up resetting
the vPMU counter registers (PMCCNTR_EL0 and/or PMEVCNTR<n>_EL0) to
zero on the first KVM_RUN after migration.
Fix this by not saving those bits when a guest writes 1 to those bits.
Fixes: ab9468340d2b ("arm64: KVM: Add access handler for PMCR register") Cc: stable@vger.kernel.org Reviewed-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Reiji Watanabe <reijiw@google.com> Link: https://lore.kernel.org/r/20230313033234.1475987-1-reijiw@google.com Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
Userspace can play some dirty tricks on us by selecting a given
PMU version (such as PMUv3p5), restore a PMCR_EL0 value that
has PMCR_EL0.LP set, and then switch the PMU version to PMUv3p1,
for example. In this situation, we end-up with PMCR_EL0.LP being
set and spreading havoc in the PMU emulation.
This is specially hard as the first two step can be done on
one vcpu and the third step on another, meaning that we need
to sanitise *all* vcpus when the PMU version is changed.
In orer to avoid a pretty complicated locking situation,
defer the sanitisation of PMCR_EL0 to the point where the
vcpu is actually run for the first tine, using the existing
KVM_REQ_RELOAD_PMU request that calls into kvm_pmu_handle_pmcr().
There is still an obscure corner case where userspace could
do the above trick, and then save the VM without running it.
They would then observe an inconsistent state (PMUv3.1 + LP set),
but that state will be fixed on the first run anyway whenever
the guest gets restored on a host.
Reported-by: Reiji Watanabe <reijiw@google.com> Signed-off-by: Marc Zyngier <maz@kernel.org>
Stable-dep-of: f6da81f650fa ("KVM: arm64: PMU: Don't save PMCR_EL0.{C,P} for the vCPU") Signed-off-by: Sasha Levin <sashal@kernel.org>
The PMU architecture makes a subtle difference between a 64bit
counter and a counter that has a 64bit overflow. This is for example
the case of the cycle counter, which can generate an overflow on
a 32bit boundary if PMCR_EL0.LC==0 despite the accumulation being
done on 64 bits.
Use this distinction in the few cases where it matters in the code,
as we will reuse this with PMUv3p5 long counters.
Ricardo recently pointed out that the PMU chained counter emulation
in KVM wasn't quite behaving like the one on actual hardware, in
the sense that a chained counter would expose an overflow on
both halves of a chained counter, while KVM would only expose the
overflow on the top half.
The difference is subtle, but significant. What does the architecture
say (DDI0087 H.a):
- Up to PMUv3p4, all counters but the cycle counter are 32bit
- A 32bit counter that overflows generates a CHAIN event on the
adjacent counter after exposing its own overflow status
- The CHAIN event is accounted if the counter is correctly
configured (CHAIN event selected and counter enabled)
This all means that our current implementation (which uses 64bit
perf events) prevents us from emulating this overflow on the lower half.
How to fix this? By implementing the above, to the letter.
This largely results in code deletion, removing the notions of
"counter pair", "chained counters", and "canonical counter".
The code is further restructured to make the CHAIN handling similar
to SWINC, as the two are now extremely similar in behaviour.
Reported-by: Ricardo Koller <ricarkol@google.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Reiji Watanabe <reijiw@google.com> Link: https://lore.kernel.org/r/20221113163832.3154370-3-maz@kernel.org
Stable-dep-of: f6da81f650fa ("KVM: arm64: PMU: Don't save PMCR_EL0.{C,P} for the vCPU") Signed-off-by: Sasha Levin <sashal@kernel.org>
"Abnormal" bios include discards, write zeroes and secure erase. By no
longer passing the calculated 'len' pointer, commit 7dd06a2548b2 ("dm:
allow dm_accept_partial_bio() for dm_io without duplicate bios") took a
senseless approach to disallowing dm_accept_partial_bio() from working
for duplicate bios processed using __send_duplicate_bios().
It inadvertently and incorrectly stopped the use of 'len' when
initializing a target's io (in alloc_tio). As such the resulting tio
could address more area of a device than it should.
For example, when discarding an entire DM striped device with the
following DM table:
vg-lvol0: 0 159744 striped 2 128 7:0 2048 7:1 2048
vg-lvol0: 159744 45056 striped 2 128 7:2 2048 7:3 2048
Before this fix:
device-mapper: striped: target_stripe=0, bdev=7:0, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop0: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
device-mapper: striped: target_stripe=1, bdev=7:1, start=2048 len=102400
blkdiscard: attempt to access beyond end of device
loop1: rw=2051, sector=2048, nr_sectors = 102400 limit=81920
In the commit referenced below I failed to pay attention to this code
also being buildable as 32-bit. Adjust the type of "ret" - there's no
real need for it to be wider than 32 bits.
Fixes: 934ef33ee75c ("x86/PVH: obtain VGA console info in Dom0") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/2d2193ff-670b-0a27-e12d-2c5c4c121c79@suse.com Signed-off-by: Juergen Gross <jgross@suse.com>
Recently, when automatically merging -net and net-next in MPTCP devel
tree, our CI reported [1] a conflict in hsr, the same as the one
reported by Stephen in netdev [2].
When looking at the conflict, I noticed it is in fact the v1 [3] that
has been applied in -net and the v2 [4] in net-next. Maybe the v1 was
applied by accident.
As mentioned by Jakub Kicinski [5], the new condition makes more sense
before the net_ratelimit(), not to update net_ratelimit's state which is
unnecessary if we're not going to print either way.
Here, this modification applies the v2 but in -net.
During miration to vram prange->offset is valid after vram buffer is located,
either use old one or allocate a new one. Move svm_range_vram_node_new before
migrate for each vma to get valid prange->offset.
v2: squash in warning fix
Fixes: b4ee9606378b ("drm/amdkfd: Fix BO offset for multi-VMA page migration") Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ucsi_init() which runs from a workqueue sets ucsi->connector and
on an error will clear it again.
ucsi->connector gets dereferenced by ucsi_resume(), this checks for
ucsi->connector being NULL in case ucsi_init() has not finished yet;
or in case ucsi_init() has failed.
ucsi_init() setting ucsi->connector and then clearing it again on
an error creates a race where the check in ucsi_resume() may pass,
only to have ucsi->connector free-ed underneath it when ucsi_init()
hits an error.
Fix this race by making ucsi_init() store the connector array in
a local variable and only assign it to ucsi->connector on success.
Fixes: bdc62f2bae8f ("usb: typec: ucsi: Simplified registration and I/O API") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230308154244.722337-3-hdegoede@redhat.com Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bug in btf_dump's logic of determining if a given struct type is
packed or not. The notion of "natural alignment" is not needed and is
even harmful in this case, so drop it altogether. The biggest difference
in btf_is_struct_packed() compared to its original implementation is
that we don't really use btf__align_of() to determine overall alignment
of a struct type (because it could be 1 for both packed and non-packed
struct, depending on specifci field definitions), and just use field's
actual alignment to calculate whether any field is requiring packing or
struct's size overall necessitates packing.
Add two simple test cases that demonstrate the difference this change
would make.
Fixes: ea2ce1ba99aa ("libbpf: Fix BTF-to-C converter's padding logic") Reported-by: Eduard Zingerman <eddyz87@gmail.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Eduard Zingerman <eddyz87@gmail.com> Link: https://lore.kernel.org/bpf/20221215183605.4149488-1-andrii@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Turns out that btf_dump API doesn't handle a bunch of tricky corner
cases, as reported by Per, and further discovered using his testing
Python script ([0]).
This patch revamps btf_dump's padding logic significantly, making it
more correct and also avoiding unnecessary explicit padding, where
compiler would pad naturally. This overall topic turned out to be very
tricky and subtle, there are lots of subtle corner cases. The comments
in the code tries to give some clues, but comments themselves are
supposed to be paired with good understanding of C alignment and padding
rules. Plus some experimentation to figure out subtle things like
whether `long :0;` means that struct is now forced to be long-aligned
(no, it's not, turns out).
Anyways, Per's script, while not completely correct in some known
situations, doesn't show any obvious cases where this logic breaks, so
this is a nice improvement over the previous state of this logic.
Some selftests had to be adjusted to accommodate better use of natural
alignment rules, eliminating some unnecessary padding, or changing it to
`type: 0;` alignment markers.
Note also that for when we are in between bitfields, we emit explicit
bit size, while otherwise we use `: 0`, this feels much more natural in
practice.
Next patch will add few more test cases, found through randomized Per's
script.
Structures with zero regular fields but some padding constitute a
special case in btf_dump.c:btf_dump_emit_struct_def with regards to
newline before closing '}'.
It is possible to trigger these VTU violation messages very easily,
it's only necessary to send packets with an unknown VLAN ID to a port
that belongs to a VLAN-aware bridge.
Do a similar thing as for ATU violation messages, and hide them in the
kernel's trace buffer.
In applications where the switch ports must perform 802.1X based
authentication and are therefore locked, ATU violation interrupts are
quite to be expected as part of normal operation. The problem is that
they currently spam the kernel log, even if rate limited.
Create a series of trace points, all derived from the same event class,
which log these violations to the kernel's trace buffer, which is both
much faster and much easier to ignore than printing to a serial console.
New usage model:
$ trace-cmd list | grep mv88e6xxx
mv88e6xxx
mv88e6xxx:mv88e6xxx_atu_full_violation
mv88e6xxx:mv88e6xxx_atu_miss_violation
mv88e6xxx:mv88e6xxx_atu_member_violation
$ trace-cmd record -e mv88e6xxx sleep 10
When an ATU violation occurs, the switch uses the ATU FID register to
report the FID of the MAC address that incurred the violation. It would
be good for the driver to know the FID value for purposes such as
logging and CPU-based authentication.
Up until now, the driver has been calling the mv88e6xxx_g1_atu_op()
function to read ATU violations, but that doesn't do exactly what we
want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0.
(side note, the documentation for the ATU Get/Clear Violation command
says that writes to the ATU FID register have no effect before the
operation starts, it's only that we disregard the value that this
register provides once the operation completes)
So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather
mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need
to write it.
The remainder of mv88e6xxx_g1_atu_op() except for
mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a
GET_CLR_VIOLATION command to the ATU. In principle we could have still
kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID
register are pointless, but in the interest of doing less CPU work per
interrupt, write a new function called mv88e6xxx_g1_read_atu_violation()
and call it.
The FID will be the port default FID as set by mv88e6xxx_port_set_fid()
if the VID from the packet cannot be found in the VTU. Otherwise it is
the FID derived from the VTU entry associated with that VID.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We walk the userspace PTs to discover what mapping size was
used there. However, this can race against the userspace tables
being freed, and we end-up in the weeds.
Thankfully, the mm code is being generous and will IPI us when
doing so. So let's implement our part of the bargain and disable
interrupts around the walk. This ensures that nothing terrible
happens during that time.
We still need to handle the removal of the page tables before
the walk. For that, allow get_user_mapping_size() to return an
error, and make sure this error can be propagated all the way
to the the exit handler.
Have KVM_GET_ONE_REG for vPMU counter (vPMC) registers (PMCCNTR_EL0
and PMEVCNTR<n>_EL0) return the sum of the register value in the sysreg
file and the current perf event counter value.
Values of vPMC registers are saved in sysreg files on certain occasions.
These saved values don't represent the current values of the vPMC
registers if the perf events for the vPMCs count events after the save.
The current values of those registers are the sum of the sysreg file
value and the current perf event counter value. But, when userspace
reads those registers (using KVM_GET_ONE_REG), KVM returns the sysreg
file value to userspace (not the sum value).
Fix this to return the sum value for KVM_GET_ONE_REG.
SKL/GLK CSC unit suffers from a nasty issue where a CSC
coeff/offset register read or write between DC5 exit and
PSR exit will undo the CSC arming performed by DMC, and
then during PSR exit the hardware will latch zeroes into
the active CSC registers. This causes any plane going
through the CSC to output all black.
We can sidestep the issue by making sure the PSR exit has
already actually happened before we touch the CSC coeff/offset
registers. Easiest way to guarantee that is to just move the
CSC programming back into the .color_commir_arm() as we force
a PSR exit (and crucially wait for it to actually happen)
prior to touching the arming registers.
When PSR (and thus also DC states) are disabled we don't
have anything to worry about, so we can keep using the
more optional _noarm() hook for writing the CSC registers.
Cc: <stable@vger.kernel.org> #v5.19+ Cc: Manasi Navare <navaremanasi@google.com> Cc: Drew Davenport <ddavenport@chromium.org> Cc: Imre Deak <imre.deak@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8283 Fixes: d13dde449580 ("drm/i915: Split pipe+output CSC programming to noarm+arm pair") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-3-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 80a892a4c2428b65366721599fc5fe50eaed35fd) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keeping DC states enabled is incompatible with the _noarm()/_arm()
split we use for writing pipe/plane registers. When DC5 and PSR
are enabled, all pipe/plane registers effectively become self-arming
on account of DC5 exit arming the update, and PSR exit latching it.
What probably saves us most of the time is that (with PIPE_MISC[21]=0)
all pipe register writes themselves trigger PSR exit, and then
we don't re-enter PSR until the idle frame count has elapsed.
So it may be that the PSR exit happens already before we've
updated the state too much.
Also the PSR1 panel (at least on this KBL) seems to discard the first
frame we trasmit, presumably still scanning out from its internal
framebuffer at that point. So only the second frame we transmit is
actually visible. But I suppose that could also be panel specific
behaviour. I haven't checked out how other PSR panels behave, nor
did I bother to check what the eDP spec has to say about this.
And since this really is all about DC states, let's switch from
the MODESET domain to the DC_OFF domain. Functionally they are
100% identical. We should probably remove the MODESET domain...
And for good measure let's toss in an assert to the place where
we do the _noarm() register writes to make sure DC states are
in fact off.
v2: Just use intel_display_power_is_enabled() (Imre)
Currently i915_gem_object_is_framebuffer() doesn't treat the
BO containing the framebuffer's DPT as a framebuffer itself.
This means eg. that the shrinker can evict the DPT BO while
leaving the actual FB BO bound, when the DPT is allocated
from regular shmem.
That causes an immediate oops during hibernate as we
try to rewrite the PTEs inside the already evicted
DPT obj.
TODO: presumably this might also be the reason for the
DPT related display faults under heavy memory pressure,
but I'm still not sure how that would happen as the object
should be pinned by intel_dpt_pin() while in active use by
the display engine...
Cc: stable@vger.kernel.org Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Imre Deak <imre.deak@intel.com> Fixes: 0dc987b699ce ("drm/i915/display: Add smem fallback allocation for dpt") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230320090522.9909-2-ville.syrjala@linux.intel.com Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
(cherry picked from commit 779cb5ba64ec7df80675a956c9022929514f517a) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / jedix / linux-maple.git / log