"ARM: 8857/1: efi: enable CP15 DMB instructions before cleaning the cache"
added some explicit handling of the CP15BEN bit in the SCTLR system
register, to ensure that CP15 barrier instructions are enabled, even
if we enter the decompressor via the EFI stub.
However, as it turns out, there are other ways in which we may end up
using CP15 barrier instructions without them being enabled. I.e., when
the decompressor startup code skips the cache_on() initially, we end
up calling cache_clean_flush() with the caches and MMU off, in which
case the CP15BEN bit in SCTLR may not be programmed either. And in
fact, cache_on() itself issues CP15 barrier instructions before actually
enabling them by programming the new SCTLR value (and issuing an ISB)
Since these routines are shared between v7 CPUs and older ones that
implement the CPUID extension as well, using the ordinary v7 barrier
instructions in this code is not possible, and so we should enable the
CP15 ones explicitly before issuing them. Note that a v7 ISB is still
required between programming the SCTLR register and using the CP15 barrier
instructions, and we should take care to branch over it if the CP15BEN
bit is already set, given that in that case, the CPU may not support it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some newer cards supported by aacraid can take up to 40s to recover
after an EEH event. This causes spurious failures in the basic EEH
self-test since the current maximim timeout is only 30s.
Fix the immediate issue by bumping the timeout to a default of 60s,
and allow the wait time to be specified via an environmental variable
(EEH_MAX_WAIT).
Reported-by: Steve Best <sbest@redhat.com> Suggested-by: Douglas Miller <dougmill@us.ibm.com> Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200122031125.25991-1-oohall@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit fb7c02445c49 ("ext4: pass -ESHUTDOWN code to jbd2 layer") want
to allow jbd2 layer to distinguish shutdown journal abort from other
error cases. So the ESHUTDOWN should be taken precedence over any other
errno which has already been recoded after EXT4_FLAGS_SHUTDOWN is set,
but it only update errno in the journal suoerblock now if the old errno
is 0.
Fixes: fb7c02445c49 ("ext4: pass -ESHUTDOWN code to jbd2 layer") Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20191204124614.45424-4-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
We invoke jbd2_journal_abort() to abort the journal and record errno
in the jbd2 superblock when committing journal transaction besides the
failure on submitting the commit record. But there is no need for the
case and we can also invoke jbd2_journal_abort() instead of
__jbd2_journal_abort_hard().
Fixes: 818d276ceb83a ("ext4: Add the journal checksum feature") Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20191204124614.45424-2-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
The alarmtimer_suspend() function will fail if an RTC device is on a bus
such as SPI or i2c and that RTC device registers and probes after
alarmtimer_init() registers and probes the 'alarmtimer' platform device.
This is because system wide suspend suspends devices in the reverse order
of their probe. When alarmtimer_suspend() attempts to program the RTC for a
wakeup it will try to program an RTC device on a bus that has already been
suspended.
Move the alarmtimer device registration to happen when the RTC which is
used for wakeup is registered. Register the 'alarmtimer' platform device as
a child of the RTC device too, so that it can be guaranteed that the RTC
device won't be suspended when alarmtimer_suspend() is called.
Reported-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200124055849.154411-2-swboyd@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Address field in device TLB invalidation descriptor is qualified
by the S field. If S field is zero, a single page at page address
specified by address [63:12] is requested to be invalidated. If S
field is set, the least significant bit in the address field with
value 0b (say bit N) indicates the invalidation address range. The
spec doesn't require the address [N - 1, 0] to be cleared, hence
remove the unnecessary WARN_ON_ONCE().
Otherwise, the caller might set "mask = MAX_AGAW_PFN_WIDTH" in order
to invalidating all the cached mappings on an endpoint, and below
overflow error will be triggered.
[...]
UBSAN: Undefined behaviour in drivers/iommu/dmar.c:1354:3
shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
Reported-and-tested-by: Frank <fgndev@posteo.de> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
RMRR entries describe memory regions that are DMA targets for devices
outside the kernel's control.
RMRR entries that fail the sanity check are pointing to regions of
memory that the firmware did not tell the kernel are reserved or
otherwise should not be used.
Instead of aborting DMAR processing, this commit marks the firmware
as tainted. These RMRRs will still be identity mapped, otherwise,
some devices, e.x. graphic devices, will not work during boot.
Signed-off-by: Barret Rhoden <brho@google.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Fixes: f036c7fa0ab60 ("iommu/vt-d: Check VT-d RMRR region in BIOS is reported as reserved") Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The patch "bcache: rework error unwinding in register_bcache" introduces
a use-after-free regression in register_bcache(). Here are current code,
2510 out_free_path:
2511 kfree(path);
2512 out_module_put:
2513 module_put(THIS_MODULE);
2514 out:
2515 pr_info("error %s: %s", path, err);
2516 return ret;
If some error happens and the above code path is executed, at line 2511
path is released, but referenced at line 2515. Then KASAN reports a use-
after-free error message.
This patch changes line 2515 in the following way to fix the problem,
2515 pr_info("error %s: %s", path?path:"", err);
Signed-off-by: Coly Li <colyli@suse.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Split the successful and error return path, and use one goto label for each
resource to unwind. This also fixes some small errors like leaking the
module reference count in the reboot case (which seems entirely harmless)
or printing the wrong warning messages for early failures.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current code doesn't correctly handle the situation which arises when
a file system that has METADATA_UUID_INCOMPAT flag set and has its FSID
changed to the one in metadata uuid. This causes the incompat flag to
disappear.
In case of a power failure we could end up in a situation where part of
the disks in a multi-disk filesystem are correctly reverted to
METADATA_UUID_INCOMPAT flag unset state, while others have
METADATA_UUID_INCOMPAT set and CHANGING_FSID_V2_IN_PROGRESS.
This patch corrects the behavior required to handle the case where a
disk of the second type is scanned first, creating the necessary
btrfs_fs_devices. Subsequently, when a disk which has already completed
the transition is scanned it should overwrite the data in
btrfs_fs_devices.
Reported-by: Su Yue <Damenly_Su@gmx.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This seems to be a false positive due to compiler version. The cause is
in the ASSERT macro implementation that does the conditional check as
IS_DEFINED(CONFIG_BTRFS_ASSERT) and not an #ifdef.
This device does not function correctly in raw mode in kernel
versions validating buffer sizes in bulk mode. It erroneously
announces 16 bits per pixel instead of 12 for NV12 format, so it
needs this quirk to fix computed frame size and avoid legitimate
frames getting discarded.
When disabling virtual functions on an SR-IOV adapter we currently do not
correctly remove the EEH state for the now-dead virtual functions. When
removing the pci_dn that was created for the VF when SR-IOV was enabled
we free the corresponding eeh_dev without removing it from the child device
list of the eeh_pe that contained it. This can result in crashes due to the
use-after-free.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com> Tested-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190821062655.19735-1-oohall@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/ethernet/mellanox/mlx5/core/wq.c: In function 'mlx5_wq_cyc_wqe_dump':
include/linux/kern_levels.h:5:18: warning: format '%ld' expects argument of type 'long int', but argument 5 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
Fixes: 130c7b46c93d ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events") Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When trying to compile with CONFIG_DEBUG_INFO_BTF enabled, I got this
error:
% make -s
Failed to generate BTF for vmlinux
Try to disable CONFIG_DEBUG_INFO_BTF
make[3]: *** [vmlinux] Error 1
Compiling again without -s shows the true error (that pahole is
missing), but since this is fatal, we should show the error
unconditionally on stderr as well, not silence it using the `info`
function. With this patch:
% make -s
BTF: .tmp_vmlinux.btf: pahole (pahole) is not available
Failed to generate BTF for vmlinux
Try to disable CONFIG_DEBUG_INFO_BTF
make[3]: *** [vmlinux] Error 1
Signed-off-by: Chris Down <chris@chrisdown.name> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20200122000110.GA310073@chrisdown.name Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the check that a u32 variable i is >= 0 is always true because
the unsigned variable will never be negative, causing the loop to run
forever. Fix this by changing the pre-decrement check to a zero check on
i followed by a decrement of i.
Addresses-Coverity: ("Unsigned compared against 0") Fixes: 39cc539f90d0 ("driver core: platform: Prevent resouce overflow from causing infinite loops") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lore.kernel.org/r/20200116175758.88396-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Debugging the kprobes code showed that the address of
getname_flags() is contained in the __bug_table. Kprobes
doesn't allow to set probes at BUG() locations.
So the BUG() is actually the last opcode of the previous function.
Fix this by switching to using the MONITOR CALL (MC) instruction,
and set the entry in __bug_table to the beginning of that MC.
Ftraced function is expected in the backtrace by ftrace kselftests, which
are now failing. It would also be nice to have it for clarity reasons.
"ftrace_caller" itself is called without stack frame allocated for it
and does not store its caller (ftraced function). Instead it simply
allocates a stack frame for "ftrace_trace_function" and sets backchain
to point to ftraced function stack frame (which contains ftraced function
caller in saved r14).
To fix this issue make "ftrace_caller" allocate a stack frame
for itself just to store ftraced function for the stack unwinder.
As a result backtrace looks like the following:
clang 10 introduces -mpacked-stack compiler option implementation. At the
same time currently it does not support a combination of -mpacked-stack
and -mbackchain. This leads to the following build error:
clang: error: unsupported option '-mpacked-stack with -mbackchain' for
target 's390x-ibm-linux'
If/when clang adds support for a combination of -mpacked-stack and
-mbackchain it would also require -msoft-float (like gcc does). According
to Ulrich Weigand "stack slot assigned to the kernel backchain overlaps
the stack slot assigned to the FPR varargs (both are required to be
placed immediately after the saved r15 slot if present)."
Extend -mpacked-stack compiler option support check to include all 3
options -mpacked-stack -mbackchain -msoft-float which must present to
support -mpacked-stack with -mbackchain.
Add TEST opcode to Group3-2 reg=001b as same as Group3-1 does.
Commit
12a78d43de76 ("x86/decoder: Add new TEST instruction pattern")
added a TEST opcode assignment to f6 XX/001/XXX (Group 3-1), but did
not add f7 XX/001/XXX (Group 3-2).
Actually, this TEST opcode variant (ModRM.reg /1) is not described in
the Intel SDM Vol2 but in AMD64 Architecture Programmer's Manual Vol.3,
Appendix A.2 Table A-6. ModRM.reg Extensions for the Primary Opcode Map.
Without this fix, Randy found a warning by insn_decoder_test related
to this issue as below.
HOSTCC arch/x86/tools/insn_decoder_test
HOSTCC arch/x86/tools/insn_sanity
TEST posttest
arch/x86/tools/insn_decoder_test: warning: Found an x86 instruction decoder bug, please report this.
arch/x86/tools/insn_decoder_test: warning: ffffffff81000bf1: f7 0b 00 01 08 00 testl $0x80100,(%rbx)
arch/x86/tools/insn_decoder_test: warning: objdump says 6 bytes, but insn_get_length() says 2
arch/x86/tools/insn_decoder_test: warning: Decoded and checked 11913894 instructions with 1 failures
TEST posttest
arch/x86/tools/insn_sanity: Success: decoded and checked 1000000 random instructions with 0 errors (seed:0x871ce29c)
To fix this error, add the TEST opcode according to AMD64 APM Vol.3.
[ bp: Massage commit message. ]
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lkml.kernel.org/r/157966631413.9580.10311036595431878351.stgit@devnote2 Signed-off-by: Sasha Levin <sashal@kernel.org>
$make ARCH=x86_64 -C tools/objtool
...
CC arch/x86/decode.o
arch/x86/decode.c:10:22: fatal error: asm/insn.h: No such file or directory
#include <asm/insn.h>
^
compilation terminated.
mv: cannot stat ‘arch/x86/.decode.o.tmp’: No such file or directory
make[2]: *** [arch/x86/decode.o] Error 1
...
The root cause is that the command-line variable 'ARCH' cannot be
overridden. It can be replaced by 'SRCARCH', which is defined in
'tools/scripts/Makefile.arch'.
$ gcc -Werror --param asan-instrument-allocas=1 -S -x c /dev/null -o /dev/null
cc1: error: invalid --param name ‘asan-instrument-allocas’; did you mean ‘asan-instrument-writes’?
$ echo $?
1
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 84d043185dbe ("spi: Add a driver for the Freescale/NXP QuadSPI controller") Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initial snd_hda_get_sub_node() can fail on certain
devices (e.g. some Chromebook models using Intel GLK).
The failure rate is very low, but as this is is part of
the probe process, end-user impact is high.
In observed cases, related hardware status registers have
expected values, but the node query still fails. Retrying
the node query does seem to help, so fix the problem by
adding retry logic to the query. This does not impact
non-Intel platforms.
The specific problem here is that the mbigen driver real probe has failed
as the mbigen_of_create_domain()->of_platform_device_create() call fails,
the reason for that being that we never destroyed the platform device
created during the remove test dry run and there is some conflict.
Since we generally would never want to unbind this driver, and to save
adding a driver tear down path for that, just set the driver
.suppress_bind_attrs member to avoid this possibility.
Change the exported symbols introduced by commit e9153311491da
("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage")
from EXPORT_SYMBOL() to EXPORT_SYMBOL_GPL(), like is used for all the core
parts.
Fixes: e9153311491da ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage") Reported-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: https://lore.kernel.org/r/20200120123921.1204339-1-enric.balletbo@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The remoteproc_core and remoteproc drivers all initialize with module_init().
However remoteproc drivers need the rproc_class during their probe. If one of
the remoteproc drivers runs init and gets through probe before
remoteproc_init() runs, a NULL pointer access of rproc_class's `glue_dirs`
spinlock occurs.
> Unable to handle kernel NULL pointer dereference at virtual address 000000dc
> pgd = c0004000
> [000000dc] *pgd=00000000
> Internal error: Oops: 5 [#1] PREEMPT ARM
> Modules linked in:
> CPU: 0 PID: 1 Comm: swapper Tainted: G W 4.14.106-rt56 #1
> Hardware name: Generic OMAP36xx (Flattened Device Tree)
> task: c6050000 task.stack: c604a000
> PC is at rt_spin_lock+0x40/0x6c
> LR is at rt_spin_lock+0x28/0x6c
> pc : [<c0523c90>] lr : [<c0523c78>] psr: 60000013
> sp : c604bdc0 ip : 00000000 fp : 00000000
> r10: 00000000 r9 : c61c7c10 r8 : c6269c20
> r7 : c0905888 r6 : c6269c20 r5 : 00000000 r4 : 000000d4
> r3 : 000000dc r2 : c6050000 r1 : 00000002 r0 : 000000d4
> Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
...
> [<c0523c90>] (rt_spin_lock) from [<c03b65a4>] (get_device_parent+0x54/0x17c)
> [<c03b65a4>] (get_device_parent) from [<c03b6bec>] (device_add+0xe0/0x5b4)
> [<c03b6bec>] (device_add) from [<c042adf4>] (rproc_add+0x18/0xd8)
> [<c042adf4>] (rproc_add) from [<c01110e4>] (my_rproc_probe+0x158/0x204)
> [<c01110e4>] (my_rproc_probe) from [<c03bb6b8>] (platform_drv_probe+0x34/0x70)
> [<c03bb6b8>] (platform_drv_probe) from [<c03b9dd4>] (driver_probe_device+0x2c8/0x420)
> [<c03b9dd4>] (driver_probe_device) from [<c03ba02c>] (__driver_attach+0x100/0x11c)
> [<c03ba02c>] (__driver_attach) from [<c03b7d08>] (bus_for_each_dev+0x7c/0xc0)
> [<c03b7d08>] (bus_for_each_dev) from [<c03b910c>] (bus_add_driver+0x1cc/0x264)
> [<c03b910c>] (bus_add_driver) from [<c03ba714>] (driver_register+0x78/0xf8)
> [<c03ba714>] (driver_register) from [<c010181c>] (do_one_initcall+0x100/0x190)
> [<c010181c>] (do_one_initcall) from [<c0800de8>] (kernel_init_freeable+0x130/0x1d0)
> [<c0800de8>] (kernel_init_freeable) from [<c051eee8>] (kernel_init+0x8/0x114)
> [<c051eee8>] (kernel_init) from [<c01175b0>] (ret_from_fork+0x14/0x24)
> Code: e2843008e3c2203ff5d3f000e5922010 (e193cf9f)
> ---[ end trace 0000000000000002 ]---
In setup_load_info(), info->name (which contains the name of the module,
mostly used for early logging purposes before the module gets set up)
gets unconditionally assigned if .modinfo is missing despite the fact
that there is an if (!info->name) check near the end of the function.
Avoid assigning a placeholder string to info->name if .modinfo doesn't
exist, so that we can fall back to info->mod->name later on.
Fixes: 5fdc7db6448a ("module: setup load info before module_sig_check()") Reviewed-by: Miroslav Benes <mbenes@suse.cz> Signed-off-by: Jessica Yu <jeyu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We had a report indicating that some read errors aren't reported by the
device stats in the userland. It is important to have the errors
reported in the device stat as user land scripts might depend on it to
take the reasonable corrective actions. But to debug these issue we need
to be really sure that request to reset the device stat did not come
from the userland itself. So log an info message when device error reset
happens.
For example:
BTRFS info (device sdc): device stats zeroed by btrfs(9223)
Reported-by: philip@philip-seeger.de Link: https://www.spinics.net/lists/linux-btrfs/msg96528.html Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fs/btrfs/file-item.c:295 btrfs_lookup_bio_sums()
warn: should this be 'count == -1'
which points to the while (count--) loop. With count == 0 the check
itself could decrement it to -1. There's a WARN_ON a few lines below
that has never been seen in practice though.
It turns out that the value of page_bytes_left matches the count (by
sectorsize multiples). The loop never reaches the state where count
would go to -1, because page_bytes_left == 0 is found first and this
breaks out.
For clarity, use only plain check on count (and only for positive
value), decrement safely inside the loop. Any other discrepancy after
the whole bio list processing should be reported by the exising
WARN_ON_ONCE as well.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A user reports a possible NULL-pointer dereference in
btrfsic_process_superblock(). We are assigning state->fs_info to a local
fs_info variable and afterwards checking for the presence of state.
While we would BUG_ON() a NULL state anyways, we can also just remove
the local fs_info copy, as fs_info is only used once as the first
argument for btrfs_num_copies(). There we can just pass in
state->fs_info as well.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205003 Signed-off-by: Johannes Thumshirn <jth@kernel.org> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/pwm/pwm-pca9685.c: In function ‘pca9685_pwm_gpio_free’:
drivers/pwm/pwm-pca9685.c:162:21: warning: variable ‘pwm’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed. In that case, hold and release
the lock 'pca->lock' can be removed since nothing will be done between
them.
The "drive->dn" variable is a u8 controlled by root.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "drive->dn" value is a u8 and it is controlled by root only, but
it could be out of bounds here so let's check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the old code (e.g.) mutex_destroy() was called before
pwmchip_remove(). Between these two calls it is possible that a PWM
callback is used which tries to grab the mutex.
The final build stage of the x86 kernel captures some symbol
addresses from the decompressor binary and copies them into zoffset.h.
It uses sed with a regular expression that matches the address, symbol
type and symbol name, and mangles the captured addresses and the names
of symbols of interest into #define directives that are added to
zoffset.h
The symbol type is indicated by a single letter, which we match
strictly: only letters in the set 'ABCDGRSTVW' are matched, even
though the actual symbol type is relevant and therefore ignored.
Commit bc7c9d620 ("efi/libstub/x86: Force 'hidden' visibility for
extern declarations") made a change to the way external symbol
references are classified, resulting in 'startup_32' now being
emitted as a hidden symbol. This prevents the use of GOT entries to
refer to this symbol via its absolute address, which recent toolchains
(including Clang based ones) already avoid by default, making this
change a no-op in the majority of cases.
However, as it turns out, the LLVM linker classifies such hidden
symbols as symbols with static linkage in fully linked ELF binaries,
causing tools such as NM to output a lowercase 't' rather than an upper
case 'T' for the type of such symbols. Since our sed expression only
matches upper case letters for the symbol type, the line describing
startup_32 is disregarded, resulting in a build error like the following
arch/x86/boot/header.S:568:18: error: symbol 'ZO_startup_32' can not be
undefined in a subtraction expression
init_size: .long (0x00000000008fd000 - ZO_startup_32 +
(((0x0000000001f6361c + ((0x0000000001f6361c >> 8) + 65536)
- 0x00000000008c32e5) + 4095) & ~4095)) # kernel initialization size
Given that we are only interested in the value of the symbol, let's match
any character in the set 'a-zA-Z' instead.
The new of_devlink support breaks PCIe probing on ARM platforms booting
via UEFI if the firmware exposes a EFI framebuffer that is backed by a
PCI device. The reason is that the probing order gets reversed,
resulting in a resource conflict on the framebuffer memory window when
the PCIe probes last, causing it to give up entirely.
Given that we rely on PCI quirks to deal with EFI framebuffers that get
moved around in memory, we cannot simply drop the memory reservation, so
instead, let's use the device link infrastructure to register this
dependency, and force the probing to occur in the expected order.
15f003d20782 ("x86/mm/pat: Don't implicitly allow _PAGE_RW in kernel_map_pages_in_pgd()")
modified kernel_map_pages_in_pgd() to manage writable permissions
of memory mappings in the EFI page table in a different way, but
in the process, it removed the ability to clear NX attributes from
read-only mappings, by clobbering the clear mask if _PAGE_RW is not
being requested.
Failure to remove the NX attribute from read-only mappings is
unlikely to be a security issue, but it does prevent us from
tightening the permissions in the EFI page tables going forward,
so let's fix it now.
`cat /sys/kernel/debug/regulator/regulator_summary` ends on a deadlock
when you have a voltage controlled regulator (vctrl).
The problem is that the vctrl_get_voltage() and vctrl_set_voltage() calls the
regulator_get_voltage() and regulator_set_voltage() and that will try to lock
again the dependent regulators (the regulator supplying the control voltage).
Fix the issue by exporting the unlocked version of the regulator_get_voltage()
and regulator_set_voltage() API so drivers that need it, like the voltage
controlled regulator driver can use it.
Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Reported-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: https://lore.kernel.org/r/20200116094543.2847321-1-enric.balletbo@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With fourth pin added for iDisp for skl_dai, update SOF_SKL_DAI_NUM to
account for the change. Without this, dais from the bottom of the list
are skipped. In current state that's the case for 'Alt Analog CPU DAI'.
The recently added API that exposes firmware mixer controls to the
kernel is missing cache handling and all writes bypass the cache, this
obviously causes the cache to get out of sync with the hardware. Factor
out the cache handling into two new helper functions and call those from
both the normal ALSA control handlers and the new kernel API.
The counters obj_pool_free, and obj_nr_tofree, and the flag obj_freeing are
read locklessly outside the pool_lock critical sections. If read with plain
accesses, this would result in data races.
This is addressed as follows:
* reads outside critical sections become READ_ONCE()s (pairing with
WRITE_ONCE()s added);
* writes become WRITE_ONCE()s (pairing with READ_ONCE()s added); since
writes happen inside critical sections, only the write and not the read
of RMWs needs to be atomic, thus WRITE_ONCE(var, var +/- X) is
sufficient.
The data races were reported by KCSAN:
BUG: KCSAN: data-race in __free_object / fill_pool
write to 0xffffffff8beb04f8 of 4 bytes by interrupt on cpu 1:
__free_object+0x1ee/0x8e0 lib/debugobjects.c:404
__debug_check_no_obj_freed+0x199/0x330 lib/debugobjects.c:969
debug_check_no_obj_freed+0x3c/0x44 lib/debugobjects.c:994
slab_free_hook mm/slub.c:1422 [inline]
read to 0xffffffff8beb04f8 of 4 bytes by task 1 on cpu 2:
fill_pool+0x3d/0x520 lib/debugobjects.c:135
__debug_object_init+0x3c/0x810 lib/debugobjects.c:536
debug_object_init lib/debugobjects.c:591 [inline]
debug_object_activate+0x228/0x320 lib/debugobjects.c:677
debug_rcu_head_queue kernel/rcu/rcu.h:176 [inline]
BUG: KCSAN: data-race in __debug_object_init / fill_pool
read to 0xffffffff8beb04f8 of 4 bytes by task 10 on cpu 6:
fill_pool+0x3d/0x520 lib/debugobjects.c:135
__debug_object_init+0x3c/0x810 lib/debugobjects.c:536
debug_object_init_on_stack+0x39/0x50 lib/debugobjects.c:606
init_timer_on_stack_key kernel/time/timer.c:742 [inline]
write to 0xffffffff8beb04f8 of 4 bytes by task 1 on cpu 3:
alloc_object lib/debugobjects.c:258 [inline]
__debug_object_init+0x717/0x810 lib/debugobjects.c:544
debug_object_init lib/debugobjects.c:591 [inline]
debug_object_activate+0x228/0x320 lib/debugobjects.c:677
debug_rcu_head_queue kernel/rcu/rcu.h:176 [inline]
BUG: KCSAN: data-race in free_obj_work / free_object
read to 0xffffffff9140c190 of 4 bytes by task 10 on cpu 6:
free_object+0x4b/0xd0 lib/debugobjects.c:426
debug_object_free+0x190/0x210 lib/debugobjects.c:824
destroy_timer_on_stack kernel/time/timer.c:749 [inline]
write to 0xffffffff9140c190 of 4 bytes by task 93 on cpu 1:
free_obj_work+0x24f/0x480 lib/debugobjects.c:313
process_one_work+0x454/0x8d0 kernel/workqueue.c:2264
worker_thread+0x9a/0x780 kernel/workqueue.c:2410
It is not an error to unplug a cable from the ENETC port even with TSN
offloads, so don't spam the log with link-related messages from the
tc-taprio offload subsystem, a single notification is sufficient:
[10972.351859] fsl_enetc 0000:00:00.0 eno0: Qbv PSPEED set speed link down.
[10972.360241] fsl_enetc 0000:00:00.0 eno0: Link is Down
Fixes: 2e47cb415f0a ("enetc: update TSN Qbv PSPEED set according to adjust link speed") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Robert reported that during boot the watchdog timestamp is set to 0 for one
second which is the indicator for a watchdog reset.
The reason for this is that the timestamp is in seconds and the time is
taken from sched clock and divided by ~1e9. sched clock starts at 0 which
means that for the first second during boot the watchdog timestamp is 0,
i.e. reset.
Use ULONG_MAX as the reset indicator value so the watchdog works correctly
right from the start. ULONG_MAX would only conflict with a real timestamp
if the system reaches an uptime of 136 years on 32bit and almost eternity
on 64bit.
AMD Family 17h processors and above gain support for Large Increment
per Cycle events. Unfortunately there is no CPUID or equivalent bit
that indicates whether the feature exists or not, so we continue to
determine eligibility based on a CPU family number comparison.
For Large Increment per Cycle events, we add a f17h-and-compatibles
get_event_constraints_f17h() that returns an even counter bitmask:
Large Increment per Cycle events can only be placed on PMCs 0, 2,
and 4 out of the currently available 0-5. The only currently
public event that requires this feature to report valid counts
is PMCx003 "Retired SSE/AVX Operations".
Note that the CPU family logic in amd_core_pmu_init() is changed
so as to be able to selectively add initialization for features
available in ranges of backward-compatible CPU families. This
Large Increment per Cycle feature is expected to be retained
in future families.
A side-effect of assigning a new get_constraints function for f17h
disables calling the old (prior to f15h) amd_get_event_constraints
implementation left enabled by commit e40ed1542dd7 ("perf/x86: Add perf
support for AMD family-17h processors"), which is no longer
necessary since those North Bridge event codes are obsoleted.
Also fix a spelling mistake whilst in the area (calulating ->
calculating).
Fixes: e40ed1542dd7 ("perf/x86: Add perf support for AMD family-17h processors") Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191114183720.19887-2-kim.phillips@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
topology.c::get_group() relies on the assumption that non-NUMA domains do
not partially overlap. Zeng Tao pointed out in [1] that such topology
descriptions, while completely bogus, can end up being exposed to the
scheduler.
In his example (8 CPUs, 2-node system), we end up with:
MC span for CPU3 == 3-7
MC span for CPU4 == 4-7
The first pass through get_group(3, sdd@MC) will result in the following
sched_group list:
3 -> 4 -> 5 -> 6 -> 7
^ /
`----------------'
And a later pass through get_group(4, sdd@MC) will "corrupt" that to:
3 -> 4 -> 5 -> 6 -> 7
^ /
`-----------'
which will completely break things like 'while (sg != sd->groups)' when
using CPU3's base sched_domain.
There already are some architecture-specific checks in place such as
x86/kernel/smpboot.c::topology.sane(), but this is something we can detect
in the core scheduler, so it seems worthwhile to do so.
Warn and abort the construction of the sched domains if such a broken
topology description is detected. Note that this is somewhat
expensive (O(t.c²), 't' non-NUMA topology levels and 'c' CPUs) and could be
gated under SCHED_DEBUG if deemed necessary.
Testing
=======
Dietmar managed to reproduce this using the following qemu incantation:
Add power-domains entry for smmu, so that the it is accessible as long
as the driver is active. Without this device shutdown is throwing the
below warning:
"[ 44.736348] arm-smmu-v3 36600000.smmu: failed to clear cr0"
Reported-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:6: warning: variable ra set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:10: warning: variable rs set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:14: warning: variable rt set but not used [-Wunused-but-set-variable]
They are not used since commit 2b33cb585f94 ("KVM: PPC: Reimplement
LOAD_FP/STORE_FP instruction mmio emulation with analyse_instr() input")
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: zhengbin <zhengbin13@huawei.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function edac_device_alloc_ctl_info() returns a
NULL pointer, not ERR_PTR(). Replace the IS_ERR() test in the return
value check with a NULL test.
[why]
Need to fix DML portability issues to enable SW unit testing around DML
[how]
Move calcs into dc include folder since multiple components reference it
Remove relative paths to external dependencies
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
These errors come from ALTERNATIVE_CB and __ALTERNATIVE_CFG,
which test for the existence of the callback parameter in inline
assembly using the following expression:
" .if " __stringify(cb) " == 0\n"
This works with GNU as, but isn't supported by LLVM. This change
splits __ALTERNATIVE_CFG and ALTINSTR_ENTRY into separate macros
to fix the LLVM build.
Link: https://github.com/ClangBuiltLinux/linux/issues/472 Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike gcc, clang considers each inline assembly block to be independent
and therefore, when using the integrated assembler for inline assembly,
any preambles that enable features must be repeated in each block.
This change defines __LSE_PREAMBLE and adds it to each inline assembly
block that has LSE instructions, which allows them to be compiled also
with clang's assembler.
Link: https://github.com/ClangBuiltLinux/linux/issues/671 Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Andrew Murray <andrew.murray@arm.com> Tested-by: Kees Cook <keescook@chromium.org> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Turns out that Tiger Lake GPIO will be enumerated using _HID method where
there is only a single ACPI device and multiple BARs so rework the driver
to support that scheme instead.
Fixes: c9ccf71fc807 ("pinctrl: intel: Add Intel Tiger Lake pin controller support") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add debugfs interface to provide debugging information of devfreq device.
It contains 'devfreq_summary' entry to show the summary of registered
devfreq devices as following and the additional debugfs file will be added.
- /sys/kernel/debug/devfreq/devfreq_summary
[Detailed description of each field of 'devfreq_summary' debugfs file]
- dev_name : Device name of h/w
- dev : Device name made by devfreq core
- parent_dev : If devfreq device uses the passive governor,
show parent devfreq device name. Otherwise, show 'null'.
- governor : Devfreq governor name
- polling_ms : If devfreq device uses the simple_ondemand governor,
polling_ms is necessary for the period. (unit: millisecond)
- cur_freq_Hz : Current frequency (unit: Hz)
- min_freq_Hz : Minimum frequency (unit: Hz)
- max_freq_Hz : Maximum frequency (unit: Hz)
Further note: MOTU is known for reusing Product IDs for different
devices or different generations of the device (e.g. MicroBook
I/II/IIc shares a single Product ID). This patch was only tested with
M4 audio interface, but the same Product ID is also used by M2. Hope
it will work for M2 as well.
A faulty userspace that calls destroy_session() before destroying the
connections can trigger the failure. This patch prevents the issue by
refusing to destroy the session if there are outstanding connections.
Pass UFS device information to vendor-specific variant callback
"apply_dev_quirks" because some platform vendors need to know such
information to apply special handling or quirks in specific devices.
At the same time, modify existing vendor implementations according to the
new interface for those vendor drivers which will be built-in or built as a
module alone with UFS core driver.
[mkp: clarified commit desc]
Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Asutosh Das <asutoshd@codeaurora.org> Cc: Avri Altman <avri.altman@wdc.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Bean Huo <beanhuo@micron.com> Cc: Can Guo <cang@codeaurora.org> Cc: Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/1578726707-6596-2-git-send-email-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bartosz Golaszewski reports that when "make {menu,n,g,x}config" fails
due to missing packages, a temporary file is left over, which is not
ignored by git.
For example, if GTK+ is not installed:
$ make gconfig
*
* Unable to find the GTK+ installation. Please make sure that
* the GTK+ 2.0 development package is correctly installed.
* You need gtk+-2.0 gmodule-2.0 libglade-2.0
*
scripts/kconfig/Makefile:208: recipe for target 'scripts/kconfig/gconf-cfg' failed
make[1]: *** [scripts/kconfig/gconf-cfg] Error 1
Makefile:567: recipe for target 'gconfig' failed
make: *** [gconfig] Error 2
$ git status
HEAD detached at v5.4
Untracked files:
(use "git add <file>..." to include in what will be committed)
scripts/kconfig/gconf-cfg.tmp
nothing added to commit but untracked files present (use "git add" to track)
This is because the check scripts are run with filechk, which misses
to clean up the temporary file on failure.
When the line
{ $(filechk_$(1)); } > $@.tmp;
... fails, it exits immediately due to the 'set -e'. Use trap to make
sure to delete the temporary file on exit.
For extra safety, I replaced $@.tmp with $(dot-target).tmp to make it
a hidden file.
We currently have musb_set_vbus() called from two different paths. Mostly
it gets called from the USB PHY via omap_musb_set_mailbox(), but in some
cases it can get also called from musb_stage0_irq() rather via .set_vbus:
This is racy and will not work with introducing generic helper functions
for musb_set_host() and musb_set_peripheral(). We want to get rid of the
busy loops in favor of usleep_range().
Let's just get rid of .set_vbus for omap2430 glue layer and let the PHY
code handle VBUS with musb_set_vbus(). Note that in the follow-up patch
we can completely remove omap2430_musb_set_vbus(), but let's do it in a
separate patch as this change may actually turn out to be needed as a
fix.
Reported-by: Pavel Machek <pavel@ucw.cz> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200115132547.364-5-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver allocates a dynamic cpu hotplug state but never releases it.
If reloaded in a loop it will quickly trigger a WARN message:
"No more dynamic states available for CPU hotplug"
Fix by calling cpuhp_remove_multi_state on remove like several other
perf pmu drivers.
Also fix the cleanup logic on probe error paths: add the missing
cpuhp_remove_multi_state call and properly check the return value from
cpuhp_state_add_instant_nocalls.
Fixes: 9a66d36cc7ac ("drivers/perf: imx_ddr: Add DDR performance counter support to perf") Acked-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I see the following lockdep splat in the qcom pinctrl driver when
attempting to suspend the device.
============================================
WARNING: possible recursive locking detected
5.4.2 #2 Tainted: G S
--------------------------------------------
cat/6536 is trying to acquire lock: ffffff814787ccc0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
but task is already holding lock: ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
This is because the msm_gpio_irq_set_wake() function calls
irq_set_irq_wake() as a backup in case the irq comes in during the path
to idle. Given that we're calling irqchip functions from within an
irqchip we need to set the lockdep class to be different for this child
controller vs. the default one that the parent irqchip gets.
This used to be done before this driver was converted to hierarchical
irq domains in commit e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in
hierarchy") via the gpiochip_irq_map() function. With hierarchical irq
domains this function has been replaced by
gpiochip_hierarchy_irq_domain_alloc(). Therefore, set the lockdep class
like was done previously in the irq domain path so we can avoid this
lockdep warning.
Fixes: fdd61a013a24 ("gpio: Add support for hierarchical IRQ domains") Cc: Thierry Reding <treding@nvidia.com> Cc: Brian Masney <masneyb@onstation.org> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Maulik Shah <mkshah@codeaurora.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200114231103.85641-1-swboyd@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing code allows changing the data device when the thin-pool
target is reloaded.
This capability is not required and only complicates device lifetime
guarantees. This can cause crashes like the one reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=1788596
where the kernel tries to issue a flush bio located in a structure that
was already freed.
Take the first step to simplifying the thin-pool's data device lifetime
by disallowing changing it. Like the thin-pool's metadata device, the
data device is now set in pool_create() and it cannot be changed for a
given thin-pool.
drivers/gpu/drm/nouveau/nouveau_ttm.c: In function nouveau_vram_manager_new:
drivers/gpu/drm/nouveau/nouveau_ttm.c:66:22: warning: variable mem set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/nouveau/nouveau_ttm.c: In function nouveau_gart_manager_new:
drivers/gpu/drm/nouveau/nouveau_ttm.c:106:22: warning: variable mem set but not used [-Wunused-but-set-variable]
They are not used any more, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Method init is typically ordered by class in the FW image as ThreeD,
TwoD, Compute.
Due to a bug in parsing the FW into our internal format, we've been
accidentally sending Twod + Compute methods to the ThreeD class, as
well as Compute methods to the TwoD class - oops.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We accidentally set "psb" which is a no-op instead of "*psb" so it
generates a static checker warning. We should probably set it before
the first error return so that it's always initialized.
Fixes: 923f1bd27bf1 ("drm/nouveau/secboot/gm20b: add secure boot support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The radio module asserts CTS when its RX buffer has 10 bytes left.
Putting just 8 instead of 16 bytes into the UART1 TX buffer on the Linux
side ensures to not overflow the RX buffer on the radio module side.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Paul Burton <paul.burton@mips.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
With CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3, the stack usage in vme_fake
grows above the warning limit:
drivers/vme/bridges/vme_fake.c: In function 'fake_master_read':
drivers/vme/bridges/vme_fake.c:610:1: error: the frame size of 1160 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
drivers/vme/bridges/vme_fake.c: In function 'fake_master_write':
drivers/vme/bridges/vme_fake.c:797:1: error: the frame size of 1160 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The problem is that in some configurations, each call to
fake_vmereadX() puts another variable on the stack.
Reduce the amount of inlining to get back to the previous state,
with no function using more than 200 bytes each.
A negative value should be returned if map->map_type is invalid
although that is impossible now, but if we run into such situation
in future, then xdpbuff could be leaked.
Daniel Borkmann suggested:
-EBADRQC should be returned to stay consistent with generic XDP
for the tracepoint output and not to be confused with -EOPNOTSUPP
from other locations like dev_map_enqueue() when ndo_xdp_xmit is
missing and such.
Fix GCC warning with W=1, previous cleanup did not remove unnecessary
variable.
sound/soc/sof/intel/hda-dai.c: In function ‘hda_link_pcm_prepare’:
sound/soc/sof/intel/hda-dai.c:265:31: warning: variable ‘hda_stream’
set but not used [-Wunused-but-set-variable]
265 | struct sof_intel_hda_stream *hda_stream;
| ^~~~~~~~~~
Fixes: a3ebccb52efdf ("ASoC: SOF: Intel: hda: reset link DMA state in prepare") Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200113205620.27285-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a device already has devres items attached before probing, a warning
backtrace is printed. However, this backtrace does not reveal the
offending device, leaving the user uninformed. Furthermore, using
WARN_ON() causes systems with panic-on-warn to reboot.
Fix this by replacing the WARN_ON() by a dev_crit() message.
Abort probing the device, to prevent doing more damage to the device's
resources.
num_resources in the platform_device struct is declared as a u32. The
for loops that iterate over num_resources use an int as the counter,
which can cause infinite loops on architectures with smaller ints.
Change the loop counters to u32.
The setup_crash_devices_work_queue function only partially initializes
the message it sends to chipset_init, leading to undefined behavior:
drivers/visorbus/visorchipset.c: In function 'setup_crash_devices_work_queue':
drivers/visorbus/visorchipset.c:333:6: error: '((unsigned char*)&msg.hdr.flags)[0]' is used uninitialized in this function [-Werror=uninitialized]
if (inmsg->hdr.flags.response_expected)
Set up the entire structure, zero-initializing the 'response_expected'
flag.
This was apparently found by the patch that added the -O3 build option
in Kconfig.
Fixes: 12e364b9f08a ("staging: visorchipset driver to provide registration and other services") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20200107202950.782951-1-arnd@arndb.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the proper form of the empty initializer when working with
structures that contain an array. Otherwise, older gcc versions (eg gcc
4.9) will complain about this.
../drivers/tty/synclink_gt.c:1337:3: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
if (C_CRTSCTS(tty)) {
^
../drivers/tty/synclink_gt.c:1335:2: note: previous statement is here
if (I_IXOFF(tty))
^
../drivers/tty/synclink_gt.c:2563:3: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
^
../drivers/tty/synclink_gt.c:2561:2: note: previous statement is here
if (I_INPCK(info->port.tty))
^
../drivers/tty/synclink_gt.c:3221:3: warning: misleading indentation;
statement is not part of the previous 'else' [-Wmisleading-indentation]
set_signals(info);
^
../drivers/tty/synclink_gt.c:3219:2: note: previous statement is here
else
^
3 warnings generated.
The indentation on these lines is not at all consistent, tabs and spaces
are mixed together. Convert to just using tabs to be consistent with the
Linux kernel coding style and eliminate these warnings from clang.
../drivers/tty/synclinkmp.c:1456:3: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
if (C_CRTSCTS(tty)) {
^
../drivers/tty/synclinkmp.c:1453:2: note: previous statement is here
if (I_IXOFF(tty))
^
../drivers/tty/synclinkmp.c:2473:8: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
info->port.tty->hw_stopped = 0;
^
../drivers/tty/synclinkmp.c:2471:7: note: previous statement is here
if ( debug_level >= DEBUG_LEVEL_ISR )
^
../drivers/tty/synclinkmp.c:2482:8: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
info->port.tty->hw_stopped = 1;
^
../drivers/tty/synclinkmp.c:2480:7: note: previous statement is here
if ( debug_level >= DEBUG_LEVEL_ISR )
^
../drivers/tty/synclinkmp.c:2809:3: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
^
../drivers/tty/synclinkmp.c:2807:2: note: previous statement is here
if (I_INPCK(info->port.tty))
^
../drivers/tty/synclinkmp.c:3246:3: warning: misleading indentation;
statement is not part of the previous 'else' [-Wmisleading-indentation]
set_signals(info);
^
../drivers/tty/synclinkmp.c:3244:2: note: previous statement is here
else
^
5 warnings generated.
The indentation on these lines is not at all consistent, tabs and spaces
are mixed together. Convert to just using tabs to be consistent with the
Linux kernel coding style and eliminate these warnings from clang.
The compilation warning is redefination showed as following:
In file included from tables.c:2:
../../../include/linux/export.h:180: warning: "EXPORT_SYMBOL" redefined
#define EXPORT_SYMBOL(sym) __EXPORT_SYMBOL(sym, "")
In file included from tables.c:1:
../../../include/linux/raid/pq.h:61: note: this is the location of the previous definition
#define EXPORT_SYMBOL(sym)
Fixes: 69a94abb82ee ("export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols") Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sound/soc/atmel/atmel_ssc_dai.o: In function `atmel_ssc_set_audio':
(.text+0x7cd): undefined reference to `atmel_pcm_dma_platform_register'
Function atmel_pcm_dma_platform_register is defined under
CONFIG SND_ATMEL_SOC_DMA, so select SND_ATMEL_SOC_DMA in
CONFIG SND_ATMEL_SOC_SSC, same to CONFIG_SND_ATMEL_SOC_PDC.
projects / users / dwmw2 / linux.git / log