Arnd Bergmann [Wed, 4 Aug 2021 14:04:59 +0000 (16:04 +0200)]
Merge branch 'arm/soc' into for-next
* arm/soc: (27 commits)
ARM: ep93xx: remove MaverickCrunch support
ARM: at91: pm: add sama7g5 shdwc
ARM: at91: pm: add pm support for SAMA7G5
ARM: at91: sama7: introduce sama7 SoC family
ARM: at91: pm: add sama7g5's pmc
ARM: at91: pm: add backup mode support for SAMA7G5
ARM: at91: pm: save ddr phy calibration data to securam
ARM: at91: pm: add sama7g5 ddr phy controller
ARM: at91: pm: add sama7g5 ddr controller
ARM: at91: pm: wait for ddr power mode off
ARM: at91: pm: add support for 2.5V LDO regulator control
ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes
ARM: at91: pm: add self-refresh support for sama7g5
ARM: at91: ddr: add registers definitions for sama7g5's ddr
ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
ARM: at91: pm: add support for waiting MCK1..4
ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g
ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh
ARM: at91: pm: use r7 instead of tmp1
ARM: at91: pm: do not initialize pdev
...
Arnd Bergmann [Wed, 4 Aug 2021 14:04:55 +0000 (16:04 +0200)]
Merge branch 'arm/drivers' into for-next
* arm/drivers:
pata: ixp4xx: Rewrite to use device tree
pata: ixp4xx: Add DT bindings
pata: ixp4xx: Refer to cmd and ctl rather than csN
pata: ixp4xx: Use IS_ENABLED() to determine endianness
pata: ixp4xx: Use local dev variable
watchdog: ixp4xx: Rewrite driver to use core
bus: ixp4xx: Add a driver for IXP4xx expansion bus
bus: ixp4xx: Add DT bindings for the IXP4xx expansion bus
Arnd Bergmann [Wed, 4 Aug 2021 14:03:40 +0000 (16:03 +0200)]
Merge tag 'ixp4xx-drivers-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/drivers
IXP4xx driver updates for modernizing the IXP4xx platforms,
taregeted for v5.15:
- Add DT bindings to the expansion bus and PATA libata driver.
- Add a new expansion bus driver.
- Rewrite the watchdog driver to use the watchdog core and
spawn from the timer (clocksource) driver.
- Refactor the PATA/libata driver to probe from the device
tree and use the expansion bus driver to manipulate chip
select timings directly.
* tag 'ixp4xx-drivers-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
pata: ixp4xx: Rewrite to use device tree
pata: ixp4xx: Add DT bindings
pata: ixp4xx: Refer to cmd and ctl rather than csN
pata: ixp4xx: Use IS_ENABLED() to determine endianness
pata: ixp4xx: Use local dev variable
watchdog: ixp4xx: Rewrite driver to use core
bus: ixp4xx: Add a driver for IXP4xx expansion bus
bus: ixp4xx: Add DT bindings for the IXP4xx expansion bus
Arnd Bergmann [Wed, 4 Aug 2021 13:58:24 +0000 (15:58 +0200)]
Merge tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc
AT91 soc for 5.15:
- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
- mach-at91 entry, Kconfig and header files
- Power Management Controller (PMC) code and associated power management
changes. Support for suspend/resume, Ultra Low Power modes and
Backup with Memory in Self-Refresh mode.
- Power management association with DDR controller and
shutdown controller for addressing this variety of modes.
* tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (26 commits)
ARM: at91: pm: add sama7g5 shdwc
ARM: at91: pm: add pm support for SAMA7G5
ARM: at91: sama7: introduce sama7 SoC family
ARM: at91: pm: add sama7g5's pmc
ARM: at91: pm: add backup mode support for SAMA7G5
ARM: at91: pm: save ddr phy calibration data to securam
ARM: at91: pm: add sama7g5 ddr phy controller
ARM: at91: pm: add sama7g5 ddr controller
ARM: at91: pm: wait for ddr power mode off
ARM: at91: pm: add support for 2.5V LDO regulator control
ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes
ARM: at91: pm: add self-refresh support for sama7g5
ARM: at91: ddr: add registers definitions for sama7g5's ddr
ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
ARM: at91: pm: add support for waiting MCK1..4
ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g
ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh
ARM: at91: pm: use r7 instead of tmp1
ARM: at91: pm: do not initialize pdev
ARM: at91: pm: check for different controllers in at91_pm_modes_init()
...
Arnd Bergmann [Wed, 4 Aug 2021 12:31:30 +0000 (14:31 +0200)]
Merge tag 'at91-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 dt for 5.15:
- add sama7g5 SoC and associated evaluation kit, the sama7g5-ek
- adaptation of some DT for sama5d27 som1 ek, sama5d4 xplained and
sama5d2 icp boards
- fixes to gpio and shutdown controller nodes for all boards
* tag 'at91-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: use the right property for shutdown controller
ARM: dts: at91: sama5d2_icp: enable digital filter for I2C nodes
ARM: dts: at91: sama5d4_xplained: change the key code of the gpio key
ARM: dts: at91: add conflict note for d3
ARM: dts: at91: add pinctrl-{names, 0} for all gpios
ARM: dts: at91: sama5d27_som1_ek: enable ADC node
ARM: dts: at91: sama5d4_xplained: Remove spi0 node
dt-bindings: atmel-sysreg: add bindings for sama7g5
ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek
dt-bindings: ARM: at91: document sama7g5ek board
Arnd Bergmann [Wed, 4 Aug 2021 12:30:26 +0000 (14:30 +0200)]
Merge tag 'ux500-dts-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 Device Tree updates for the v5.15 kernel cycle:
- New device trees for these mobile phones:
- Samsung Gavini
- Samsung Codina
- Samsung Kyle
- Flag eMMC cards as non-SD non-SDIO to save time
- Link USB PHY to USB controller in the device tree
- Fix up the operating points to the actual clock frequencies
* tag 'ux500-dts-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Adjust operating points to reality
ARM: dts: ux500: Add a device tree for Kyle
ARM: dts: ux500: Add devicetree for Codina
ARM: dts: ux500: ab8500: Link USB PHY to USB controller node
ARM: dts: ux500: Flag eMMCs as non-SDIO/SD
ARM: dts: ux500: Add device tree for Samsung Gavini
Arnd Bergmann [Sat, 27 Feb 2021 12:40:09 +0000 (13:40 +0100)]
ARM: ep93xx: remove MaverickCrunch support
The MaverickCrunch support for ep93xx never made it into glibc and
was removed from gcc in its 4.8 release in 2012. It is now one of
the last parts of arch/arm/ that fails to build with the clang
integrated assembler, which is unlikely to ever want to support it.
The two alternatives are to force the use of binutils/gas when
building the crunch support, or to remove it entirely.
According to Hartley Sweeten:
"Martin Guy did a lot of work trying to get the maverick crunch working
but I was never able to successfully use it for anything. It "kind"
of works but depending on the EP93xx silicon revision there are still
a number of hardware bugs that either give imprecise or garbage results.
I have no problem with removing the kernel support for the maverick
crunch."
Unless someone else comes up with a good reason to keep it around,
remove it now. This touches mostly the ep93xx platform, but removes
a bit of code from ARM common ptrace and signal frame handling as well.
If there are remaining users of MaverickCrunch, they can use LTS
kernels for at least another five years before kernel support ends.
This rewrites the IXP4xx CF (IDE) libata driver to use the
device tree exclusively to look up its resources:
- Probe exclusively from the device tree and look up all
resources from there.
- Allocate a local state container with devres and pass
this around in .private_data.
- Initialize with struct ata_port_info.
- Use the .set_piomode() callback instead of the much
wider .set_mode(), we only support PIO after all.
- Bump driver version number from 0.2 to 1.0 to reflect this
wider change.
- Get a handle on the expansion bus syscon regmap to alter
the timings on the chip select.
- Put in the more elaborate timing adjustment code for PIO0
to PIO4 in 8 and 16bit mode from the downstream OpenWrt
patch.
The board file initialization path and platform data include
is dropped because the board files will be deleted at the same
time as this patch is merged.
The platform data file is not deleted right now so as not to
conflict with the removal of board files.
pata: ixp4xx: Refer to cmd and ctl rather than csN
The two "cs0" and "cs1" are "chip selects" but on some
platforms such as GW2358 they are actually both in CS3
making this terminology very confusing. Call the
addresses "cmd" and "ctl" after function instead.
Linus Walleij [Mon, 26 Aug 2019 14:38:14 +0000 (16:38 +0200)]
watchdog: ixp4xx: Rewrite driver to use core
This rewrites the IXP4xx watchdog driver as follows:
- Spawn the watchdog driver as a platform device from the timer
driver. It's one device in the hardware, and the fact that
Linux splits the handling into two different devices is
a Linux pecularity, and thus it becomes a Linux pecularity
to spawn a separate watchdog driver.
- Spawn the watchdog driver from the timer driver at probe().
This is well after the timer driver as actually registered and
started and we know the register base is available.
- Instead of looping back callbacks to the timer drivers for all
watchdog calls, pass the register base to the watchdog driver
and manage the registers there. The two drivers aren't even
interested in the same register so the spinlock is totally
surplus, delete it.
- Replace pretty much all of the content in the watchdog driver
with a simple, modern watchdog driver utilizing the watchdog
core instead of registering its own misc device and ioctl()
handling.
- Drop module parameters as the same already exist in the
watchdog core.
What remains is a slim elegant (IMO) watchdog driver using the
watchdog core, spawning from device tree or boardfile alike.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
bus: ixp4xx: Add a driver for IXP4xx expansion bus
The Intel IXP4xx SoCs have an expansion bus that is usually just
used for flash memory and configured by the boot loaders and can
be accessed using the "simple-bus".
However some devices need more elaborate configuration and then we
need to provide a proper 3-unit address space indicating chip
select for each device and provide timing and similar information.
Cc: Marc Zyngier <maz@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Arnd Bergmann [Tue, 3 Aug 2021 15:05:35 +0000 (17:05 +0200)]
Merge tag 'omap-for-v5.14/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.14-rc series
Some fixes for regressions and boot issues for various devices:
- Fix gpt12 system timer regression on earlier beagleboard revisions
- Fix potential NULL pointer access for omap_hwmod_get_pwrdm()
- Disable RNG on secure am335x variants as it's not accessible
- Fix flakey DCDC2 voltage causing hangs on am43x-epos-evm by reducing
i2c0 bus speed for tps65218
- Fix typo for am437x-l4 can@0 node
- Fix omap5 regression caused by vdds_1v8_main fixed-regulator
* tag 'omap-for-v5.14/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
omap5-board-common: remove not physically existing vdds_1v8_main fixed-regulator
ARM: dts: am437x-l4: fix typo in can@0 node
ARM: dts: am43x-epos-evm: Reduce i2c0 bus speed for tps65218
bus: ti-sysc: AM3: RNG is GP only
ARM: omap2+: hwmod: fix potential NULL pointer access
bus: ti-sysc: Fix gpt12 system timer issue with reserved status
Arnd Bergmann [Tue, 3 Aug 2021 08:12:34 +0000 (10:12 +0200)]
soc: ixp4xx/qmgr: fix invalid __iomem access
Sparse reports a compile time warning when dereferencing an
__iomem pointer:
drivers/soc/ixp4xx/ixp4xx-qmgr.c:149:37: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:153:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:154:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:38: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:44: warning: dereference of noderef expression
Use __raw_readl() here for consistency with the rest of the file.
This should really get converted to some proper accessor, as the
__raw functions are not meant to be used in drivers, but the driver
has used these since the start, so for the moment, let's only fix
the warning.
Reported-by: kernel test robot <lkp@intel.com> Fixes: d4c9e9fc9751 ("IXP42x: Add QMgr support for IXP425 rev. A0 processors.") Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 8 Nov 2019 08:43:06 +0000 (09:43 +0100)]
soc: ixp4xx: fix printing resources
When compile-testing with 64-bit resource_size_t, gcc reports an invalid
printk format string:
In file included from include/linux/dma-mapping.h:7,
from drivers/soc/ixp4xx/ixp4xx-npe.c:15:
drivers/soc/ixp4xx/ixp4xx-npe.c: In function 'ixp4xx_npe_probe':
drivers/soc/ixp4xx/ixp4xx-npe.c:694:18: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n",
Use the special %pR format string to print the resources.
Arnd Bergmann [Mon, 2 Aug 2021 13:29:34 +0000 (15:29 +0200)]
Merge tag 'renesas-drivers-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.15
- Initial support for the new R-Car H3e-2G and M3e-2G SoCs.
* tag 'renesas-drivers-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: Identify R-Car H3e-2G and M3e-2G
Arnd Bergmann [Mon, 2 Aug 2021 13:28:35 +0000 (15:28 +0200)]
Merge tag 'renesas-dt-bindings-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.15
- Document support for the new R-Car H3e-2G and M3e-2G SoCs and
boards.
* tag 'renesas-dt-bindings-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Document R-Car H3e-2G and M3e-2G SoCs and boards
Arnd Bergmann [Mon, 2 Aug 2021 13:23:21 +0000 (15:23 +0200)]
Merge tag 'renesas-arm-dt-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.15
- Switches support for the Draak and Ebisu development boards,
- I2C support on RZ/G2L,
- I2C EEPROM support on the Ebisu development board,
- Sound support for the R-Car D3 SoC and the Draak development board,
- Support for the new R-Car H3e-2G and M3e-2G SoCs on the Salvator-XS
and ULCB development boards,
- IOMMU support for DMAC, EtherAVB, and SDHI on the R-Car M3-W+ SoC,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (29 commits)
arm64: dts: renesas: r8a77961: Add iommus to ipmmu_ds[01] related nodes
arm64: dts: renesas: Add support for M3ULCB+Kingfisher with R-Car M3e-2G
arm64: dts: renesas: Add support for M3ULCB with R-Car M3e-2G
arm64: dts: renesas: Add support for Salvator-XS with R-Car M3e-2G
arm64: dts: renesas: Add support for H3ULCB+Kingfisher with R-Car H3e-2G
arm64: dts: renesas: Add support for H3ULCB with R-Car H3e-2G
arm64: dts: renesas: Add support for Salvator-XS with R-Car H3e-2G
arm64: dts: renesas: Add Renesas R8A779M3 SoC support
arm64: dts: renesas: Add Renesas R8A779M1 SoC support
arm64: dts: renesas: hihope-rzg2-ex: Add EtherAVB internal rx delay
arm64: dts: renesas: r8a77995: draak: Add R-Car Sound support
arm64: dts: renesas: r8a77995: Add R-Car Sound support
arm64: dts: renesas: rcar-gen3: Add SoC model to comment headers
arm64: dts: renesas: r8a77990: ebisu: Add I2C EEPROM for PMIC
arm64: dts: renesas: r8a77995: draak: Remove bogus adv7511w properties
arm64: dts: renesas: beacon: Enable micbias
arm64: dts: renesas: r9a07g044: Add I2C nodes
arm64: dts: renesas: r8a779a0: Restore sort order
arm64: dts: renesas: r8a77990: ebisu: Add SW4 support
arm64: dts: renesas: r8a77995: draak: Add SW56 support
...
Cristian Ciocaltea [Mon, 28 Jun 2021 07:28:17 +0000 (12:58 +0530)]
ARM: dts: owl-s500-roseapplepi: Add ethernet support
Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi
SBC. Additionally, provide the necessary properties for the generic S500
ethernet node in order to setup PHY and MDIO.
Arnd Bergmann [Mon, 2 Aug 2021 13:21:39 +0000 (15:21 +0200)]
Merge branch 'arm/fixes' into for-next
* arm/fixes: (28 commits)
ARM: ixp4xx: goramo_mlr depends on old PCI driver
ARM: ixp4xx: fix compile-testing soc drivers
soc/tegra: Make regulator couplers depend on CONFIG_REGULATOR
ARM: dts: nomadik: Fix up interrupt controller node names
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
arm64: dts: armada-3720-turris-mox: remove mrvl,i2c-fast-mode
arm64: dts: armada-3720-turris-mox: fixed indices for the SDHC controllers
ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins
ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init
ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz
arm64: dts: ls1028: sl28: fix networking for variant 2
firmware: tee_bnxt: Release TEE shm, session, and context during kexec
tpm_ftpm_tee: Free and unregister TEE shared memory during kexec
tee: Correct inappropriate usage of TEE_SHM_DMA_BUF flag
tee: add tee_shm_alloc_kernel_buf()
optee: Clear stale cache entries during initialization
optee: fix tee out of memory failure seen during kexec reboot
optee: Refuse to load the driver under the kdump kernel
...
Arnd Bergmann [Mon, 2 Aug 2021 12:38:24 +0000 (14:38 +0200)]
Merge tag 'mvebu-fixes-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.14 (part 1)
- Fix i2c property for armada-3720-turris-mox in order to use SFP
- Add mmc alias on armada-3720-turris-mox to allow rootfs using the
right mmc
* tag 'mvebu-fixes-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada-3720-turris-mox: remove mrvl,i2c-fast-mode
arm64: dts: armada-3720-turris-mox: fixed indices for the SDHC controllers
Arnd Bergmann [Mon, 2 Aug 2021 12:37:13 +0000 (14:37 +0200)]
Merge tag 'stm32-dt-for-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.14, round 1
Highlights:
-----------
-Fixes are for DHCOM/DHCOR boards:
- Set HW RTC ad default RTC
- Disable EDPD LAN8710 feature as it is not a stable feature.
- Fix touchscreen IRQ line assignment
* tag 'stm32-dt-for-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
Arnd Bergmann [Mon, 2 Aug 2021 12:35:17 +0000 (14:35 +0200)]
Merge tag 'tee-kexec-fixes-for-v5.14' of git://git.linaro.org:/people/jens.wiklander/linux-tee into arm/fixes
tee: Improve support for kexec and kdump
This fixes several bugs uncovered while exercising the OP-TEE, ftpm
(firmware TPM), and tee_bnxt_fw (Broadcom BNXT firmware manager) drivers
with kexec and kdump (emergency kexec) based workflows.
* tag 'tee-kexec-fixes-for-v5.14' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
firmware: tee_bnxt: Release TEE shm, session, and context during kexec
tpm_ftpm_tee: Free and unregister TEE shared memory during kexec
tee: Correct inappropriate usage of TEE_SHM_DMA_BUF flag
tee: add tee_shm_alloc_kernel_buf()
optee: Clear stale cache entries during initialization
optee: fix tee out of memory failure seen during kexec reboot
optee: Refuse to load the driver under the kdump kernel
optee: Fix memory leak when failing to register shm pages
Arnd Bergmann [Mon, 2 Aug 2021 12:33:45 +0000 (14:33 +0200)]
Merge tag 'imx-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.14:
- A couple of fixes on MMDC driver to add missing iounmap() and
clk_disable_unprepare(), and a follow-up fix.
- Fix missing-prototypes warning in SRC driver.
- Revert commit 7d981405d0fd ("soc: imx8m: change to use platform
driver"), which breaks i.MX8M system that has CAAM driver enabled.
- One fix on imx53-m53menlo pinctrl configuration.
- Increase the PHY reset duration for imx6qdl-sr-som to fix intermittent
issues where the PHY would be unresponsive every once in a while.
- Add missing flag for in-band signalling between PHY and MAC on
kontron-sl28-var2 board to fix network support.
- Limit the SDIO Clock on Colibri iMX6ULL to 25MHz for fixing wireless
noise issue.
- Fix sysclk node name for LS1028A so that U-Boot is able to update the
"clock-frequency" property.
* tag 'imx-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins
ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init
ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz
arm64: dts: ls1028: sl28: fix networking for variant 2
Revert "soc: imx8m: change to use platform driver"
ARM: dts: imx6qdl-sr-som: Increase the PHY reset duration to 10ms
ARM: imx: common: Move prototype outside the SMP block
ARM: imx: add missing clk_disable_unprepare()
ARM: imx: add missing iounmap()
arm64: dts: ls1028a: fix node name for the sysclk
When this driver is disabled, the board file fails to build,
so add a dependency:
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_pci_preinit':
arch/arm/mach-ixp4xx/goramo_mlr.c:472:9: error: implicit declaration of function 'ixp4xx_pci_preinit'; did you mean 'iop3xx_pci_preinit'? [-Werror=implicit-function-declaration]
472 | ixp4xx_pci_preinit();
| ^~~~~~~~~~~~~~~~~~
| iop3xx_pci_preinit
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_pci_postinit':
arch/arm/mach-ixp4xx/goramo_mlr.c:481:22: error: implicit declaration of function 'ixp4xx_pci_read' [-Werror=implicit-function-declaration]
481 | if (!ixp4xx_pci_read(addr, NP_CMD_CONFIGREAD, &value)) {
| ^~~~~~~~~~~~~~~
arch/arm/mach-ixp4xx/goramo_mlr.c:231:35: error: 'IXP4XX_UART1_BASE_PHYS' undeclared here (not in a function)
231 | .start = IXP4XX_UART1_BASE_PHYS,
| ^~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_init':
arch/arm/mach-ixp4xx/goramo_mlr.c:376:9: error: implicit declaration of function 'ixp4xx_sys_init' [-Werror=implicit-function-declaration]
376 | ixp4xx_sys_init();
| ^~~~~~~~~~~~~~~
Fix it by always entering the drivers/soc/ixp4xx/ directory, and fix the
resulting compile test failures by removing the #include statements
that prevent building on most other platforms.
soc/tegra: Make regulator couplers depend on CONFIG_REGULATOR
The regulator coupler drivers now use regulator-driver API function that
isn't available during compile-testing. Make regulator coupler drivers
dependent on CONFIG_REGULATOR in Kconfig.
Fixes: 03978d42ed0d ("soc/tegra: regulators: Bump voltages on system reboot") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 2 Aug 2021 12:27:43 +0000 (14:27 +0200)]
Merge tag 'tegra-for-5.14-rc3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.14-rc3
This contains one more fix for SMMU enablement on Tegra194, this time
for PCIe.
* tag 'tegra-for-5.14-rc3-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support for PCIe on Tegra194
Nicolas Ferre [Thu, 29 Jul 2021 14:28:27 +0000 (16:28 +0200)]
ARM: dts: at91: use the right property for shutdown controller
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Linus Walleij [Sun, 1 Aug 2021 23:30:14 +0000 (01:30 +0200)]
ARM: dts: ux500: Adjust operating points to reality
The operating points should correspond to the actual frequencies
supported for the CPU. Other patches have fixed so these are
rounded and reported properly, this fixes the device trees to
match.
The Codina variant has a lower frequency than other devices so
indicate this in the device tree.
Linus Torvalds [Sun, 1 Aug 2021 19:25:30 +0000 (12:25 -0700)]
Merge tag 'perf-tools-fixes-for-v5.14-2021-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Revert "perf map: Fix dso->nsinfo refcounting", this makes 'perf top'
abort, uncovering a design flaw on how namespace information is kept.
The fix for that is more than we can do right now, leave it for the
next merge window.
- Split --dump-raw-trace by AUX records for ARM's CoreSight, fixing up
the decoding of some records.
- Fix PMU alias matching.
Thanks to James Clark and John Garry for these fixes.
* tag 'perf-tools-fixes-for-v5.14-2021-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
Revert "perf map: Fix dso->nsinfo refcounting"
perf pmu: Fix alias matching
perf cs-etm: Split --dump-raw-trace by AUX records
Linus Torvalds [Sun, 1 Aug 2021 19:18:44 +0000 (12:18 -0700)]
Merge tag 'powerpc-5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Don't use r30 in VDSO code, to avoid breaking existing Go lang
programs.
- Change an export symbol to allow non-GPL modules to use spinlocks
again.
Thanks to Paul Menzel, and Srikar Dronamraju.
* tag 'powerpc-5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/vdso: Don't use r30 to avoid breaking Go lang
powerpc/pseries: Fix regression while building external modules
Linus Torvalds [Sun, 1 Aug 2021 19:07:23 +0000 (12:07 -0700)]
Merge tag 'xfs-5.14-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"This contains a bunch of bug fixes in XFS.
Dave and I have been busy the last couple of weeks to find and fix as
many log recovery bugs as we can find; here are the results so far. Go
fstests -g recoveryloop! ;)
- Fix a number of coordination bugs relating to cache flushes for
metadata writeback, cache flushes for multi-buffer log writes, and
FUA writes for single-buffer log writes
- Fix a bug with incorrect replay of attr3 blocks
- Fix unnecessary stalls when flushing logs to disk
- Fix spoofing problems when recovering realtime bitmap blocks"
* tag 'xfs-5.14-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: prevent spoofing of rtbitmap blocks when recovering buffers
xfs: limit iclog tail updates
xfs: need to see iclog flags in tracing
xfs: Enforce attr3 buffer recovery order
xfs: logging the on disk inode LSN can make it go backwards
xfs: avoid unnecessary waits in xfs_log_force_lsn()
xfs: log forces imply data device cache flushes
xfs: factor out forced iclog flushes
xfs: fix ordering violation between cache flushes and tail updates
xfs: fold __xlog_state_release_iclog into xlog_state_release_iclog
xfs: external logs need to flush data device
xfs: flush data dev on external log write
Merge tag '5.14-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three cifs/smb3 fixes, including two for stable, and a fix for an
fallocate problem noticed by Clang"
* tag '5.14-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: add missing parsing of backupuid
smb3: rc uninitialized in one fallocate path
SMB3: fix readpage for large swap cache
- mlx5e: RX, avoid possible data corruption w/ relaxed ordering and
LRO
- phy: re-add check for PHY_BRCM_DIS_TXCRXC_NOENRGY on the BCM54811
PHY
- sctp: fix return value check in __sctp_rcv_asconf_lookup
Previous releases - always broken:
- bpf:
- more spectre corner case fixes, introduce a BPF nospec
instruction for mitigating Spectre v4
- fix OOB read when printing XDP link fdinfo
- sockmap: fix cleanup related races
- mac80211: fix enabling 4-address mode on a sta vif after assoc
- can:
- raw: raw_setsockopt(): fix raw_rcv panic for sock UAF
- j1939: j1939_session_deactivate(): clarify lifetime of session
object, avoid UAF
- fix number of identical memory leaks in USB drivers
- tipc:
- do not blindly write skb_shinfo frags when doing decryption
- fix sleeping in tipc accept routine"
* tag 'net-5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
gve: Update MAINTAINERS list
can: esd_usb2: fix memory leak
can: ems_usb: fix memory leak
can: usb_8dev: fix memory leak
can: mcba_usb_start(): add missing urb->transfer_dma initialization
can: hi311x: fix a signedness bug in hi3110_cmd()
MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver
bpf: Fix leakage due to insufficient speculative store bypass mitigation
bpf: Introduce BPF nospec instruction for mitigating Spectre v4
sis900: Fix missing pci_disable_device() in probe and remove
net: let flow have same hash in two directions
nfc: nfcsim: fix use after free during module unload
tulip: windbond-840: Fix missing pci_disable_device() in probe and remove
sctp: fix return value check in __sctp_rcv_asconf_lookup
nfc: s3fwrn5: fix undefined parameter values in dev_err()
net/mlx5: Fix mlx5_vport_tbl_attr chain from u16 to u32
net/mlx5e: Fix nullptr in mlx5e_hairpin_get_mdev()
net/mlx5: Unload device upon firmware fatal error
net/mlx5e: Fix page allocation failure for ptp-RQ over SF
net/mlx5e: Fix page allocation failure for trap-RQ over SF
...
Merge tag 'acpi-5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a recent IRQ resources handling modification that turned
out to be problematic, fix suspend-to-idle handling on AMD platforms
to take upcoming systems into account properly and fix the retrieval
of the DPTF attributes of the PCH FIVR.
Specifics:
- Revert recent change of the ACPI IRQ resources handling that
attempted to improve the ACPI IRQ override selection logic, but
introduced serious regressions on some systems (Hui Wang).
- Fix up quirks for AMD platforms in the suspend-to-idle support code
so as to take upcoming systems using uPEP HID AMDI007 into account
as appropriate (Mario Limonciello).
- Fix the code retrieving DPTF attributes of the PCH FIVR so that it
agrees on the return data type with the ACPI control method
evaluated for this purpose (Srinivas Pandruvada)"
* tag 'acpi-5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: DPTF: Fix reading of attributes
Revert "ACPI: resources: Add checks for ACPI IRQ override"
ACPI: PM: Add support for upcoming AMD uPEP HID AMDI007
Since commit 1b6b26ae7053 ("pipe: fix and clarify pipe write wakeup
logic") we have sanitized the pipe write logic, and would only try to
wake up readers if they needed it.
In particular, if the pipe already had data in it before the write,
there was no point in trying to wake up a reader, since any existing
readers must have been aware of the pre-existing data already. Doing
extraneous wakeups will only cause potential thundering herd problems.
However, it turns out that some Android libraries have misused the EPOLL
interface, and expected "edge triggered" be to "any new write will
trigger it". Even if there was no edge in sight.
Quoting Sandeep Patil:
"The commit 1b6b26ae7053 ('pipe: fix and clarify pipe write wakeup
logic') changed pipe write logic to wakeup readers only if the pipe
was empty at the time of write. However, there are libraries that
relied upon the older behavior for notification scheme similar to
what's described in [1]
One such library 'realm-core'[2] is used by numerous Android
applications. The library uses a similar notification mechanism as GNU
Make but it never drains the pipe until it is full. When Android moved
to v5.10 kernel, all applications using this library stopped working.
The library has since been fixed[3] but it will be a while before all
applications incorporate the updated library"
Our regression rule for the kernel is that if applications break from
new behavior, it's a regression, even if it was because the application
did something patently wrong. Also note the original report [4] by
Michal Kerrisk about a test for this epoll behavior - but at that point
we didn't know of any actual broken use case.
So add the extraneous wakeup, to approximate the old behavior.
[ I say "approximate", because the exact old behavior was to do a wakeup
not for each write(), but for each pipe buffer chunk that was filled
in. The behavior introduced by this change is not that - this is just
"every write will cause a wakeup, whether necessary or not", which
seems to be sufficient for the broken library use. ]
It's worth noting that this adds the extraneous wakeup only for the
write side, while the read side still considers the "edge" to be purely
about reading enough from the pipe to allow further writes.
See commit f467a6a66419 ("pipe: fix and clarify pipe read wakeup logic")
for the pipe read case, which remains that "only wake up if the pipe was
full, and we read something from it".
This makes 'perf top' abort in some cases, and the right fix will
involve surgery that is too much to do at this stage, so revert for now
and fix it in the next merge window.
Merge tag 'block-5.14-2021-07-30' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- gendisk freeing fix (Christoph)
- blk-iocost wake ordering fix (Tejun)
- tag allocation error handling fix (John)
- loop locking fix. While this isn't the prettiest fix in the world,
nobody has any good alternatives for 5.14. Something to likely
revisit for 5.15. (Tetsuo)
* tag 'block-5.14-2021-07-30' of git://git.kernel.dk/linux-block:
block: delay freeing the gendisk
blk-iocost: fix operation ordering in iocg_wake_fn()
blk-mq-sched: Fix blk_mq_sched_alloc_tags() error handling
loop: reintroduce global lock for safe loop_validate_file() traversal
Merge tag 'libata-5.14-2021-07-30' of git://git.kernel.dk/linux-block
Pull libata fixlets from Jens Axboe:
- A fix for PIO highmem (Christoph)
- Kill HAVE_IDE as it's now unused (Lukas)
* tag 'libata-5.14-2021-07-30' of git://git.kernel.dk/linux-block:
arch: Kconfig: clean up obsolete use of HAVE_IDE
libata: fix ata_pio_sector for CONFIG_HIGHMEM
Merge tag 'for-5.14-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix -Warray-bounds warning, to help external patchset to make it
default treewide
- fix writeable device accounting (syzbot report)
- fix fsync and log replay after a rename and inode eviction
- fix potentially lost error code when submitting multiple bios for
compressed range
* tag 'for-5.14-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: calculate number of eb pages properly in csum_tree_block
btrfs: fix rw device counting in __btrfs_free_extra_devids
btrfs: fix lost inode on log replay after mix of fsync, rename and inode eviction
btrfs: mark compressed range uptodate only if all bio succeed
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- resume timing fix for intel-ish driver (Ye Xiang)
- fix for using incorrect MMIO register in amd_sfh driver (Dylan
MacKenzie)
- Cintiq 24HDT / 27QHDT regression fix and touch processing fix for
Wacom driver (Jason Gerecke)
- device removal bugfix for ft260 driver (Michael Zaidman)
- other small assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: ft260: fix device removal due to USB disconnect
HID: wacom: Skip processing of touches with negative slot values
HID: wacom: Re-enable touch by default for Cintiq 24HDT / 27QHDT
HID: Kconfig: Fix spelling mistake "Uninterruptable" -> "Uninterruptible"
HID: apple: Add support for Keychron K1 wireless keyboard
HID: fix typo in Kconfig
HID: ft260: fix format type warning in ft260_word_show()
HID: amd_sfh: Use correct MMIO register for DMA address
HID: asus: Remove check for same LED brightness on set
HID: intel-ish-hid: use async resume function
Subsystems affected by this patch series: lib, ocfs2, and mm (slub,
migration, and memcg)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memcg: fix NULL pointer dereference in memcg_slab_free_hook()
slub: fix unreclaimable slab stat for bulk free
mm/migrate: fix NR_ISOLATED corruption on 64-bit
mm: memcontrol: fix blocking rstat function called from atomic cgroup1 thresholding code
ocfs2: issue zeroout to EOF blocks
ocfs2: fix zero out valid data
lib/test_string.c: move string selftest in the Runtime Testing menu
Jakub Kicinski [Fri, 30 Jul 2021 17:29:52 +0000 (19:29 +0200)]
Merge tag 'linux-can-fixes-for-5.14-20210730' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-07-30
The first patch is by me and adds Yasushi SHOJI as a reviewer for the
Microchip CAN BUS Analyzer Tool driver.
Dan Carpenter's patch fixes a signedness bug in the hi311x driver.
Pavel Skripkin provides 4 patches, the first targets the mcba_usb
driver by adding the missing urb->transfer_dma initialization, which
was broken in a previous commit. The last 3 patches fix a memory leak
in the usb_8dev, ems_usb and esd_usb2 driver.
* tag 'linux-can-fixes-for-5.14-20210730' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: esd_usb2: fix memory leak
can: ems_usb: fix memory leak
can: usb_8dev: fix memory leak
can: mcba_usb_start(): add missing urb->transfer_dma initialization
can: hi311x: fix a signedness bug in hi3110_cmd()
MAINTAINERS: add Yasushi SHOJI as reviewer for the Microchip CAN BUS Analyzer Tool driver
====================
When kmalloc_node() a large memory, page is allocated, not slab, so when
freeing memory via kfree_rcu(), this large memory should not be used by
memcg_slab_free_hook(), because memcg_slab_free_hook() is is used for
slab.
Using page_objcgs_check() instead of page_objcgs() in
memcg_slab_free_hook() to fix this bug.
Link: https://lkml.kernel.org/r/20210728145655.274476-1-wanghai38@huawei.com Fixes: 270c6a71460e ("mm: memcontrol/slab: Use helpers to access slab page's memcg_data") Signed-off-by: Wang Hai <wanghai38@huawei.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Roman Gushchin <guro@fb.com> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB uses page allocator for higher order allocations and update
unreclaimable slab stat for such allocations. At the moment, the bulk
free for SLUB does not share code with normal free code path for these
type of allocations and have missed the stat update. So, fix the stat
update by common code. The user visible impact of the bug is the
potential of inconsistent unreclaimable slab stat visible through
meminfo and vmstat.
Link: https://lkml.kernel.org/r/20210728155354.3440560-1-shakeelb@google.com Fixes: 6a486c0ad4dc ("mm, sl[ou]b: improve memory accounting") Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Roman Gushchin <guro@fb.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Similar to commit 2da9f6305f30 ("mm/vmscan: fix NR_ISOLATED_FILE
corruption on 64-bit") avoid using unsigned int for nr_pages. With
unsigned int type the large unsigned int converts to a large positive
signed long.
Symptoms include CMA allocations hanging forever due to
alloc_contig_range->...->isolate_migratepages_block waiting forever in
"while (unlikely(too_many_isolated(pgdat)))".
Link: https://lkml.kernel.org/r/20210728042531.359409-1-aneesh.kumar@linux.ibm.com Fixes: c5fc5c3ae0c8 ("mm: migrate: account THP NUMA migration counters correctly") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Reported-by: Michael Ellerman <mpe@ellerman.id.au> Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: David Hildenbrand <david@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Thu, 29 Jul 2021 21:53:44 +0000 (14:53 -0700)]
mm: memcontrol: fix blocking rstat function called from atomic cgroup1 thresholding code
Dan Carpenter reports:
The patch 2d146aa3aa84: "mm: memcontrol: switch to rstat" from Apr
29, 2021, leads to the following static checker warning:
kernel/cgroup/rstat.c:200 cgroup_rstat_flush()
warn: sleeping in atomic context
mm/memcontrol.c
3572 static unsigned long mem_cgroup_usage(struct mem_cgroup *memcg, bool swap)
3573 {
3574 unsigned long val;
3575
3576 if (mem_cgroup_is_root(memcg)) {
3577 cgroup_rstat_flush(memcg->css.cgroup);
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This is from static analysis and potentially a false positive. The
problem is that mem_cgroup_usage() is called from __mem_cgroup_threshold()
which holds an rcu_read_lock(). And the cgroup_rstat_flush() function
can sleep.
3578 val = memcg_page_state(memcg, NR_FILE_PAGES) +
3579 memcg_page_state(memcg, NR_ANON_MAPPED);
3580 if (swap)
3581 val += memcg_page_state(memcg, MEMCG_SWAP);
3582 } else {
3583 if (!swap)
3584 val = page_counter_read(&memcg->memory);
3585 else
3586 val = page_counter_read(&memcg->memsw);
3587 }
3588 return val;
3589 }
__mem_cgroup_threshold() indeed holds the rcu lock. In addition, the
thresholding code is invoked during stat changes, and those contexts
have irqs disabled as well. If the lock breaking occurs inside the
flush function, it will result in a sleep from an atomic context.
Use the irqsafe flushing variant in mem_cgroup_usage() to fix this.
Link: https://lkml.kernel.org/r/20210726150019.251820-1-hannes@cmpxchg.org Fixes: 2d146aa3aa84 ("mm: memcontrol: switch to rstat") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Chris Down <chris@chrisdown.name> Reviewed-by: Rik van Riel <riel@surriel.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Thu, 29 Jul 2021 21:53:41 +0000 (14:53 -0700)]
ocfs2: issue zeroout to EOF blocks
For punch holes in EOF blocks, fallocate used buffer write to zero the
EOF blocks in last cluster. But since ->writepage will ignore EOF
pages, those zeros will not be flushed.
This "looks" ok as commit 6bba4471f0cc ("ocfs2: fix data corruption by
fallocate") will zero the EOF blocks when extend the file size, but it
isn't. The problem happened on those EOF pages, before writeback, those
pages had DIRTY flag set and all buffer_head in them also had DIRTY flag
set, when writeback run by write_cache_pages(), DIRTY flag on the page
was cleared, but DIRTY flag on the buffer_head not.
When next write happened to those EOF pages, since buffer_head already
had DIRTY flag set, it would not mark page DIRTY again. That made
writeback ignore them forever. That will cause data corruption. Even
directio write can't work because it will fail when trying to drop pages
caches before direct io, as it found the buffer_head for those pages
still had DIRTY flag set, then it will fall back to buffer io mode.
To make a summary of the issue, as writeback ingores EOF pages, once any
EOF page is generated, any write to it will only go to the page cache,
it will never be flushed to disk even file size extends and that page is
not EOF page any more. The fix is to avoid zero EOF blocks with buffer
write.
The following code snippet from qemu-img could trigger the corruption.
Link: https://lkml.kernel.org/r/20210722054923.24389-2-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Thu, 29 Jul 2021 21:53:38 +0000 (14:53 -0700)]
ocfs2: fix zero out valid data
If append-dio feature is enabled, direct-io write and fallocate could
run in parallel to extend file size, fallocate used "orig_isize" to
record i_size before taking "ip_alloc_sem", when
ocfs2_zeroout_partial_cluster() zeroout EOF blocks, i_size maybe already
extended by ocfs2_dio_end_io_write(), that will cause valid data zeroed
out.
Link: https://lkml.kernel.org/r/20210722054923.24389-1-junxiao.bi@oracle.com Fixes: 6bba4471f0cc ("ocfs2: fix data corruption by fallocate") Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/test_string.c: move string selftest in the Runtime Testing menu
STRING_SELFTEST is presented in the "Library routines" menu. Move it in
Kernel hacking > Kernel Testing and Coverage > Runtime Testing together
with other similar tests found in lib/
--- Runtime Testing
<*> Test functions located in the hexdump module at runtime
<*> Test string functions (NEW)
<*> Test functions located in the string_helpers module at runtime
<*> Test strscpy*() family of functions at runtime
<*> Test kstrto*() family of functions at runtime
<*> Test printf() family of functions at runtime
<*> Test scanf() family of functions at runtime
Link: https://lkml.kernel.org/r/20210719185158.190371-1-mcroce@linux.microsoft.com Signed-off-by: Matteo Croce <mcroce@microsoft.com> Cc: Peter Rosin <peda@axentia.se> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arch-specific Kconfig files use HAVE_IDE to indicate if IDE is
supported.
As IDE support and the HAVE_IDE config vanishes with commit b7fb14d3ac63
("ide: remove the legacy ide driver"), there is no need to mention
HAVE_IDE in all those arch-specific Kconfig files.
The issue was identified with ./scripts/checkkconfigsymbols.py.
Fixes: b7fb14d3ac63 ("ide: remove the legacy ide driver") Suggested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210728182115.4401-1-lukas.bulwahn@gmail.com Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Marek Vasut [Wed, 21 Jul 2021 18:10:40 +0000 (20:10 +0200)]
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
While 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.
Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.
Fixes: 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Wed, 21 Jul 2021 18:12:53 +0000 (20:12 +0200)]
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Sun, 20 Jun 2021 18:54:21 +0000 (20:54 +0200)]
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
The DHCOM SoM has two RTC, one is the STM32 RTC built into the SoC
and another is Microcrystal RV RTC. By default, only the later has
battery backup, the former does not. The order in which the RTCs
are probed on boot is random, which means the kernel might pick up
system time from the STM32 RTC which has no battery backup. This
then leads to incorrect initial system time setup, even though the
HW RTC has correct time configured in it.
Add DT alias entries, so that the RTCs get assigned fixed IDs and
the HW RTC is always picked by the kernel as the default RTC, thus
resulting in correct system time in early userspace.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Hihope boards use Realtek PHY. From the very beginning it use only
tx delays. However the phy driver commit bbc4d71d63549bcd003
("net: phy: realtek: fix rtl8211e rx/tx delay config") introduced
NFS mount failure. Now it needs rx delay inaddition to tx delay
for NFS mount to work. This patch fixes NFS mount failure issue
by adding MAC internal rx delay.
arm64: dts: renesas: rcar-gen3: Add SoC model to comment headers
Make sure the R-Car Gen3 SoC model present is documented in the comment
header of each board DTS, on a single line. This makes it easier to
identify boards that are available with different SoC or SiP options.
Stephan Gerhold [Fri, 9 Jul 2021 18:22:34 +0000 (20:22 +0200)]
ARM: dts: ux500: ab8500: Link USB PHY to USB controller node
At the moment the AB8500 USB PHY driver still uses the old USB PHY
subsystem instead of the generic PHY subsystem. This means that there
is no explicit link between the USB controller and the USB PHY.
In U-Boot the PHY driver is integrated in the generic PHY subsystem,
so we need to use the typical PHY device tree bindings to specify
which PHY belongs to the USB controller.
Add the link between USB controller and PHY to both ste-ab8500.dtsi
and ste-ab8505.dtsi. This is mainly for U-Boot for now and will just
be ignored in Linux. However, if the AB8500 USB PHY driver in Linux
is moved to the generic PHY subsystem at some point these device tree
changes can be used as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 24 Jun 2021 09:17:33 +0000 (11:17 +0200)]
ARM: dts: ux500: Flag eMMCs as non-SDIO/SD
We use the no-sdio and no-sd flags to indicate that these eMMCs
are neither, so that the operating system can skip trying to
identify them as SDIO or SD during boot, which just takes time.
Pavel Skripkin [Tue, 27 Jul 2021 17:00:46 +0000 (20:00 +0300)]
can: esd_usb2: fix memory leak
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Pavel Skripkin [Tue, 27 Jul 2021 17:00:33 +0000 (20:00 +0300)]
can: ems_usb: fix memory leak
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Pavel Skripkin [Tue, 27 Jul 2021 16:59:57 +0000 (19:59 +0300)]
can: usb_8dev: fix memory leak
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c02557174b ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.
In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().
All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.
| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
Dan Carpenter [Thu, 29 Jul 2021 14:12:46 +0000 (17:12 +0300)]
can: hi311x: fix a signedness bug in hi3110_cmd()
The hi3110_cmd() is supposed to return zero on success and negative
error codes on failure, but it was accidentally declared as a u8 when
it needs to be an int type.
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver") Link: https://lore.kernel.org/r/20210729141246.GA1267@kili Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Merge tag 'drm-fixes-2021-07-30' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular drm fixes pull, seems about the right size, lots of small
fixes across the board, mostly amdgpu, but msm and i915 are in there
along with panel and ttm.
amdgpu:
- Fix resource leak in an error path
- Avoid stack contents exposure in error path
- pmops check fix for S0ix vs S3
- DCN 2.1 display fixes
- DCN 2.0 display fix
- Backlight control fix for laptops with HDR panels
- Maintainers updates
i915:
- Fix vbt port mask
- Fix around reading the right DSC disable fuse in display_ver 10
- Split display version 9 and 10 in intel_setup_outputs
* tag 'drm-fixes-2021-07-30' of git://anongit.freedesktop.org/drm/drm:
maintainers: add bugs and chat URLs for amdgpu
drm/amdgpu/display: only enable aux backlight control for OLED panels
drm/amd/display: ensure dentist display clock update finished in DCN20
drm/amd/display: Add missing DCN21 IP parameter
drm/amd/display: Guard DST_Y_PREFETCH register overflow in DCN21
drm/amdgpu: Check pmops for desired suspend state
drm/msm/dp: Initialize dp->aux->drm_dev before registration
drm/msm/dp: signal audio plugged change at dp_pm_resume
drm/msm/dp: Initialize the INTF_CONFIG register
drm/msm/dp: use dp_ctrl_off_link_stream during PHY compliance test run
drm/msm: Fix display fault handling
drm/msm/dpu: Fix sm8250_mdp register length
drm/amdgpu: Avoid printing of stack contents on firmware load error
drm/amdgpu: Fix resource leak on probe error path
drm/i915/display: split DISPLAY_VER 9 and 10 in intel_setup_outputs()
drm/i915: fix not reading DSC disable fuse in GLK
drm/i915/bios: Fix ports mask
drm/panel: panel-simple: Fix proper bpc for ytc700tlag_05_201c
drm/ttm: Initialize debugfs from ttm_global_init()
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha updates from Matt Turner:
"They're mostly small janitorial fixes but there's also more important
ones:
- drop the alpha-specific x86 binary loader (David Hildenbrand)
- regression fix for at least Marvel platforms (Mike Rapoport)
- fix for a scary-looking typo (Zheng Yongjun)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: register early reserved memory in memblock
alpha: fix spelling mistakes
alpha: Remove space between * and parameter name
alpha: fp_emul: avoid init/cleanup_module names
alpha: Add syscall_get_return_value()
binfmt: remove support for em86 (alpha only)
alpha: fix typos in a comment
alpha: defconfig: add necessary configs for boot testing
alpha: Send stop IPI to send to online CPUs
alpha: convert comma to semicolon
alpha: remove undef inline in compiler.h
alpha: Kconfig: Replace HTTP links with HTTPS ones
alpha: __udiv_qrnnd should be exported
Gustavo A. R. Silva [Mon, 26 Jul 2021 20:33:53 +0000 (15:33 -0500)]
scsi: acornscsi: Fix fall-through warning for clang
Fix the following fallthrough warning (on ARM):
drivers/scsi/arm/acornscsi.c:2651:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case res_success:
^
drivers/scsi/arm/acornscsi.c:2651:2: note: insert '__attribute__((fallthrough));' to silence this warning
case res_success:
^
__attribute__((fallthrough));
drivers/scsi/arm/acornscsi.c:2651:2: note: insert 'break;' to avoid fall-through
case res_success:
^
break; Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/lkml/202107260355.bF00i5bi-lkp@intel.com/ Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix MTE shared page detection
- Enable selftest's use of PMU registers when asked to
s390:
- restore 5.13 debugfs names
x86:
- fix sizes for vcpu-id indexed arrays
- fixes for AMD virtualized LAPIC (AVIC)
- other small bugfixes
Generic:
- access tracking performance test
- dirty_log_perf_test command line parsing fix
- Fix selftest use of obsolete pthread_yield() in favour of
sched_yield()
- use cpu_relax when halt polling
- fixed missing KVM_CLEAR_DIRTY_LOG compat ioctl"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add missing compat KVM_CLEAR_DIRTY_LOG
KVM: use cpu_relax when halt polling
KVM: SVM: use vmcb01 in svm_refresh_apicv_exec_ctrl
KVM: SVM: tweak warning about enabled AVIC on nested entry
KVM: SVM: svm_set_vintr don't warn if AVIC is active but is about to be deactivated
KVM: s390: restore old debugfs names
KVM: SVM: delay svm_vcpu_init_msrpm after svm->vmcb is initialized
KVM: selftests: Introduce access_tracking_perf_test
KVM: selftests: Fix missing break in dirty_log_perf_test arg parsing
x86/kvm: fix vcpu-id indexed array sizes
KVM: x86: Check the right feature bit for MSR_KVM_ASYNC_PF_ACK access
docs: virt: kvm: api.rst: replace some characters
KVM: Documentation: Fix KVM_CAP_ENFORCE_PV_FEATURE_CPUID name
KVM: nSVM: Swap the parameter order for svm_copy_vmrun_state()/svm_copy_vmloadsave_state()
KVM: nSVM: Rename nested_svm_vmloadsave() to svm_copy_vmloadsave_state()
KVM: arm64: selftests: get-reg-list: actually enable pmu regs in pmu sublist
KVM: selftests: change pthread_yield to sched_yield
KVM: arm64: Fix detection of shared VMAs on guest fault
projects / users / jedix / linux-maple.git / log