The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.
When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.
Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.
Cc: stable@vger.kernel.org Reported-by: Philip Langdale <philipl@overt.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Philip Langdale <philipl@overt.org> Tested-by: Philip Langdale <philipl@overt.org> Tested-by: Manuel Presnitz <mail@mpy.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IP datasheet says this controller is compatible with SD Host
Specification Version v4.00.
As it turned out, the ADMA of this IP does not work with 64-bit mode
when it is in the Version 3.00 compatible mode; it understands the
old 64-bit descriptor table (as defined in SDHCI v2), but the ADMA
System Address Register (SDHCI_ADMA_ADDRESS) cannot point to the
64-bit address.
I noticed this issue only after commit bd2e75633c80 ("dma-contiguous:
use fallback alloc_pages for single pages"). Prior to that commit,
dma_set_mask_and_coherent() returned the dma address that fits in
32-bit range, at least for the default arm64 configuration
(arch/arm64/configs/defconfig). Now the host->adma_addr exceeds the
32-bit limit, causing the real problem for the Socionext SoCs.
(As a side-note, I was also able to reproduce the issue for older
kernels by turning off CONFIG_DMA_CMA.)
HS200 is not implemented in the driver, but the controller claims it
through caps. Remove it via a quirk, to make sure the mmc core do not try
to enable HS200, as it causes the eMMC initialization to fail.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WRITE_PROTECT bit is always in a "protected mode" on Tegra and
WP-GPIO state need to be used instead. In a case of the GPIO absence,
write-enable should be assumed. External SD is writable once again as
a result of this patch because the offending commit changed behaviour for
the case of a missing WP-GPIO to fall back to WRITE_PROTECT bit-checking,
which is incorrect for Tegra.
A guest is not allowed to inject a SGI (or clear its pending state)
by writing to GICD_ISPENDR0 (resp. GICD_ICPENDR0), as these bits are
defined as WI (as per ARM IHI 0048B 4.3.7 and 4.3.8).
Make sure we correctly emulate the architecture.
Fixes: 96b298000db4 ("KVM: arm/arm64: vgic-new: Add PENDING registers handlers") Cc: stable@vger.kernel.org # 4.7+ Reported-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ap_list is longer than 256 entries, merge_final() in list_sort()
will call the comparison callback with the same element twice, causing
a deadlock in vgic_irq_cmp().
H_PUT_TCE_INDIRECT handlers receive a page with up to 512 TCEs from
a guest. Although we verify correctness of TCEs before we do anything
with the existing tables, there is a small window when a check in
kvmppc_tce_validate might pass and right after that the guest alters
the page of TCEs, causing an early exit from the handler and leaving
srcu_read_lock(&vcpu->kvm->srcu) (virtual mode) or lock_rmap(rmap)
(real mode) locked.
This fixes the bug by jumping to the common exit code with an appropriate
unlock.
Commit 9392bd98bba760be96ee ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") add a function get_tdp_amd(), the parameter is CPU
family. But the rapl_probe_amd() function use wrong model parameter.
Fix the wrong caller parameter of get_tdp_amd() to use family.
Cc: <stable@vger.kernel.org> # v5.1+ Signed-off-by: Pu Wen <puwen@hygon.cn> Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option named "auto_delink_en" is a bit misleading, as setting it to
false doesn't really disable auto-delink but let auto-delink be firmware
controlled.
Update the description to reflect the real usage of this parameter.
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
After _gadget_stop_activity is executed, we can consider the hardware
operation for gadget has finished, and the udc can be stopped and enter
low power mode. So, any later hardware operations (from usb_ep_ops APIs
or usb_gadget_ops APIs) should be considered invalid, any deinitializatons
has been covered at _gadget_stop_activity.
I meet this problem when I plug out usb cable from PC using mass_storage
gadget, my callstack like: vbus interrupt->.vbus_session->
composite_disconnect ->pm_runtime_put_sync(&_gadget->dev),
the composite_disconnect will call fsg_disable, but fsg_disable calls
usb_ep_disable using async way, there are register accesses for
usb_ep_disable. So sometimes, I get system hang due to visit register
without clock, sometimes not.
The Linux Kernel USB maintainer Alan Stern suggests this kinds of solution.
See: http://marc.info/?l=linux-usb&m=138541769810983&w=2.
Using managed device resources in usb_hcd_pci_probe() allows devm usage for
resource subranges, such as the mmio resource for the platform device
created to control host/device mode mux, which is a xhci extended
capability, and sits inside the xhci mmio region.
If managed device resources are not used then "parent" resource
is released before subrange at driver removal as .remove callback is
called before the devres list of resources for this device is walked
and released.
This has been observed with the xhci extended capability driver causing a
use-after-free which is now fixed.
An additional nice benefit is that error handling on driver initialisation
is simplified much.
In case of a disconnect an ongoing flush() has to be made fail.
Nevertheless we cannot be sure that any pending URB has already
finished, so although they will never succeed, they still must
not be touched.
The clean solution for this is to check for WDM_IN_USE
and WDM_DISCONNECTED in flush(). There is no point in ever
clearing WDM_IN_USE, as no further writes make sense.
The race between adding a function probe and reading the probes that exist
is very subtle. It needs a comment. Also, the issue can also happen if the
probe has has the EMPTY_HASH as its func_hash.
Cc: stable@vger.kernel.org Fixes: 7b60f3d876156 ("ftrace: Dynamically create the probe ftrace_ops for the trace_array") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In register_ftrace_function_probe(), we are not checking the return
value of alloc_and_copy_ftrace_hash(). The subsequent call to
ftrace_match_records() may end up dereferencing the same. Add a check to
ensure this doesn't happen.
The test (ftrace_set_ftrace_filter.sh) is part of ftrace stress tests
and the crash happens when the test does 'cat
$TRACING_PATH/set_ftrace_filter'.
The address points to the second line below, in t_probe_next(), where
filter_hash is dereferenced:
hash = iter->probe->ops.func_hash->filter_hash;
size = 1 << hash->size_bits;
This happens due to a race with register_ftrace_function_probe(). A new
ftrace_func_probe is created and added into the func_probes list in
trace_array under ftrace_lock. However, before initializing the filter,
we drop ftrace_lock, and re-acquire it after acquiring regex_lock. If
another process is trying to read set_ftrace_filter, it will be able to
acquire ftrace_lock during this window and it will end up seeing a NULL
filter_hash.
Fix this by just checking for a NULL filter_hash in t_probe_next(). If
the filter_hash is NULL, then this probe is just being added and we can
simply return from here.
The G700 suffers from the same issue than the G502:
when plugging it in, the driver tries to contact it but it fails.
This timeout is problematic as it introduce a delay in the boot,
and having only the mouse event node means that the hardware
macros keys can not be relayed to the userspace.
Link: https://github.com/libratbag/libratbag/issues/797 Fixes: 91cf9a98ae41 ("HID: logitech-hidpp: make .probe usbhid capable") Cc: stable@vger.kernel.org # v5.2 Reviewed-by: Filipe Laíns <lains@archlinux.org> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Although APIC initialization will typically clear out the LDR before
setting it, the APIC cleanup code should reset the LDR.
This was discovered with a 32-bit KVM guest jumping into a kdump
kernel. The stale bits in the LDR triggered a bug in the KVM APIC
implementation which caused the destination mapping for VCPUs to be
corrupted.
Note that this isn't intended to paper over the KVM APIC bug. The kernel
has to clear the LDR when resetting the APIC registers except when X2APIC
is enabled.
This lacks a Fixes tag because missing to clear LDR goes way back into pre
git history.
[ tglx: Made x2apic_enabled a function call as required ]
Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20190826101513.5080-3-bsd@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Legacy apic init uses bigsmp for smp systems with 8 and more CPUs. The
bigsmp APIC implementation uses physical destination mode, but it
nevertheless initializes LDR and DFR. The LDR even ends up incorrectly with
multiple bit being set.
This does not cause a functional problem because LDR and DFR are ignored
when physical destination mode is active, but it triggered a problem on a
32-bit KVM guest which jumps into a kdump kernel.
The multiple bits set unearthed a bug in the KVM APIC implementation. The
code which creates the logical destination map for VCPUs ignores the
disabled state of the APIC and ends up overwriting an existing valid entry
and as a result, APIC calibration hangs in the guest during kdump
initialization.
Remove the bogus LDR/DFR initialization.
This is not intended to work around the KVM APIC bug. The LDR/DFR
ininitalization is wrong on its own.
The issue goes back into the pre git history. The fixes tag is the commit
in the bitkeeper import which introduced bigsmp support in 2003.
ftrace does not use text_poke() for enabling trace functionality. It uses
its own mechanism and flips the whole kernel text to RW and back to RO.
The CPA rework removed a loop based check of 4k pages which tried to
preserve a large page by checking each 4k page whether the change would
actually cover all pages in the large page.
This resulted in endless loops for nothing as in testing it turned out that
it actually never preserved anything. Of course testing missed to include
ftrace, which is the one and only case which benefitted from the 4k loop.
As a consequence enabling function tracing or ftrace based kprobes results
in a full 4k split of the kernel text, which affects iTLB performance.
The kernel RO protection is the only valid case where this can actually
preserve large pages.
All other static protections (RO data, data NX, PCI, BIOS) are truly
static. So a conflict with those protections which results in a split
should only ever happen when a change of memory next to a protected region
is attempted. But these conflicts are rightfully splitting the large page
to preserve the protected regions. In fact a change to the protected
regions itself is a bug and is warned about.
Add an exception for the static protection check for kernel text RO when
the to be changed region spawns a full large page which allows to preserve
the large mappings. This also prevents the syslog to be spammed about CPA
violations when ftrace is used.
The exception needs to be removed once ftrace switched over to text_poke()
which avoids the whole issue.
Fixes: 585948f4f695 ("x86/mm/cpa: Avoid the 4k pages check completely") Reported-by: Song Liu <songliubraving@fb.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Song Liu <songliubraving@fb.com> Reviewed-by: Song Liu <songliubraving@fb.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908282355340.1938@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit processes running on a 64-bit kernel are not always detected
correctly, causing the process to crash when uretprobes are installed.
The reason for the crash is that in_ia32_syscall() is used to determine the
process's mode, which only works correctly when called from a syscall.
In the case of uretprobes, however, the function is called from a exception
and always returns 'false' on a 64-bit kernel. In consequence this leads to
corruption of the process's return address.
Fix this by using user_64bit_mode() instead of in_ia32_syscall(), which
is correct in any situation.
[ tglx: Add a comment and the following historical info ]
This should have been detected by the rename which happened in commit
abfb9498ee13 ("x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()")
which states in the changelog:
The is_ia32_task()/is_x32_task() function names are a big misnomer: they
suggests that the compat-ness of a system call is a task property, which
is not true, the compatness of a system call purely depends on how it
was invoked through the system call layer.
.....
and then it went and blindly renamed every call site.
Sadly enough this was already mentioned here:
8faaed1b9f50 ("uprobes/x86: Introduce sizeof_long(), cleanup adjust_ret_addr() and
arch_uretprobe_hijack_return_addr()")
where the changelog says:
TODO: is_ia32_task() is not what we actually want, TS_COMPAT does
not necessarily mean 32bit. Fortunately syscall-like insns can't be
probed so it actually works, but it would be better to rename and
use is_ia32_frame().
and goes all the way back to:
0326f5a94dde ("uprobes/core: Handle breakpoint and singlestep exceptions")
Oh well. 7+ years until someone actually tried a uretprobe on a 32bit
process on a 64bit kernel....
Don't advance RIP or inject a single-step #DB if emulation signals a
fault. This logic applies to all state updates that are conditional on
clean retirement of the emulation instruction, e.g. updating RFLAGS was
previously handled by commit 38827dbd3fb85 ("KVM: x86: Do not update
EFLAGS on faulting emulation").
Not advancing RIP is likely a nop, i.e. ctxt->eip isn't updated with
ctxt->_eip until emulation "retires" anyways. Skipping #DB injection
fixes a bug reported by Andy Lutomirski where a #UD on SYSCALL due to
invalid state with EFLAGS.TF=1 would loop indefinitely due to emulation
overwriting the #UD with #DB and thus restarting the bad SYSCALL over
and over.
Cc: Nadav Amit <nadav.amit@gmail.com> Cc: stable@vger.kernel.org Reported-by: Andy Lutomirski <luto@kernel.org> Fixes: 663f4c61b803 ("KVM: x86: handle singlestep during emulation") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kvm_intel is loaded with nested=0 parameter an attempt to perform
KVM_GET_SUPPORTED_HV_CPUID results in OOPS as nested_get_evmcs_version hook
in kvm_x86_ops is NULL (we assign it in nested_vmx_hardware_setup() and
this only happens in case nested is enabled).
Check that kvm_x86_ops->nested_get_evmcs_version is not NULL before
calling it. With this, we can remove the stub from svm as it is no
longer needed.
recalculate_apic_map does not santize ldr and it's possible that
multiple bits are set. In that case, a previous valid entry
can potentially be overwritten by an invalid one.
This condition is hit when booting a 32 bit, >8 CPU, RHEL6 guest and then
triggering a crash to boot a kdump kernel. This is the sequence of
events:
1. Linux boots in bigsmp mode and enables PhysFlat, however, it still
writes to the LDR which probably will never be used.
2. However, when booting into kdump, the stale LDR values remain as
they are not cleared by the guest and there isn't a apic reset.
3. kdump boots with 1 cpu, and uses Logical Destination Mode but the
logical map has been overwritten and points to an inactive vcpu.
Signed-off-by: Radim Krcmar <rkrcmar@redhat.com> Signed-off-by: Bandan Das <bsd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk function snd_emuusb_set_samplerate() has a NULL check for
the mixer element, but this is useless in the current code. It used
to be a check against mixer->id_elems[unitid] but it was changed later
to the value after mixer_eleme_list_to_info() which is always non-NULL
due to the container_of() usage.
This patch fixes the check before the conversion.
While we're at it, correct a typo in the comment in the function,
too.
Fixes: 8c558076c740 ("ALSA: usb-audio: Clean up mixer element list traverse") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The input pool of a client might be deleted via the resize ioctl, the
the access to it should be covered by the proper locks. Currently the
only missing place is the call in snd_seq_ioctl_get_client_pool(), and
this patch papers over it.
"enabled" parameter historically referred to the device input or
output, not to the led indicator. After the changes added with the led
helper functions the mic mute led logic refers to the led and not to
the mic input which caused led indicator to be negated.
Fixing logic in cxt_update_gpio_led and updated
cxt_fixup_gpio_mute_hook
Also updated debug messages to ease further debugging if necessary.
Fixes: 184e302b46c9 ("ALSA: hda/conexant - Use the mic-mute LED helper") Suggested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jeronimo Borque <jeronimo@borque.com.ar> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I forgot to release the allocated object at the early error path in
line6_init_pcm(). For addressing it, slightly shuffle the code so
that the PCM destructor (pcm->private_free) is assigned properly
before all error paths.
The bmControls (for UAC1) or bmMixerControls (for UAC2/3) bitmap has a
variable size depending on both input and output pins. Its size is to
fit with input * output bits. The problem is that the input size
can't be determined simply from the unit descriptor itself but it
needs to parse the whole connected sources. Although the
uac_mixer_unit_get_channels() tries to check some possible overflow of
this bitmap, it's incomplete due to the lack of the evaluation of
input pins.
For covering possible overflows, this patch adds the bitmap overflow
check in the loop of input pins in parse_audio_mixer_unit().
Fixes: 0bfe5e434e66 ("ALSA: usb-audio: Check mixer unit descriptors more strictly") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In decode_session{4,6} there is a possibility that the skb dst dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the skb_dst(skb)->dev is actually not needed as we
called decode_session{4,6} via xfrm_decode_session_reverse(), so oif is not
used by: fl4->flowi4_oif = reverse ? skb->skb_iif : oif;
So make a dst dev check here should be clean and safe.
v4: No changes.
v3: No changes.
v2: fix the issue in decode_session{4,6} instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnels") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __icmp_send() there is a possibility that the rt->dst.dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
- ip6gre_tunnel_xmit
- ip6gre_xmit_ipv4
- __gre6_xmit
- ip6_tnl_xmit
- if skb->len - t->tun_hlen - eth_hlen > mtu; return -EMSGSIZE
- icmp_send
- net = dev_net(rt->dst.dev); <-- here
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the reason we need rt->dst.dev is to get the net.
So we can just try get it from skb->dev when rt->dst.dev is NULL.
v4: Julian Anastasov remind skb->dev also could be NULL. We'd better
still use dst.dev and do a check to avoid crash.
v3: No changes.
v2: fix the issue in __icmp_send() instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: c8b34e680a09 ("ip_tunnel: Add tnl_update_pmtu in ip_md_tunnel_xmit") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Julian Anastasov <ja@ssi.bg> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a conntrack cache issue with timeout policy.
Currently, we do not check if the timeout extension is set properly in the
cached conntrack entry. Thus, after packet recirculate from conntrack
action, the timeout policy is not applied properly. This patch fixes the
aforementioned issue.
Fixes: 06bd2bdf19d2 ("openvswitch: Add timeout support to ct action") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using mpls over gre/gre6 setup, rt->rt_gw4 address is not set, the
same for rt->rt_gw_family. Therefore, when rt->rt_gw_family is checked
in mpls_xmit(), neigh_xmit() call is skipped. As a result, such setup
doesn't work anymore.
This issue was found with LTP mpls03 tests.
Fixes: 1550c171935d ("ipv4: Prepare rtable for IPv6 gateway") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jason Baron explained in commit 790ba4566c1a ("tcp: set SOCK_NOSPACE
under memory pressure"), it is crucial we properly set SOCK_NOSPACE
when needed.
However, Jason patch had a bug, because the 'nonblocking' status
as far as sk_stream_wait_memory() is concerned is governed
by MSG_DONTWAIT flag passed at sendmsg() time :
long timeo = sock_sndtimeo(sk, flags & MSG_DONTWAIT);
So it is very possible that tcp sendmsg() calls sk_stream_wait_memory(),
and that sk_stream_wait_memory() returns -EAGAIN with SOCK_NOSPACE
cleared, if sk->sk_sndtimeo has been set to a small (but not zero)
value.
This patch removes the 'noblock' variable since we must always
set SOCK_NOSPACE if -EAGAIN is returned.
It also renames the do_nonblock label since we might reach this
code path even if we were in blocking mode.
Fixes: 790ba4566c1a ("tcp: set SOCK_NOSPACE under memory pressure") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Reported-by: Vladimir Rutsky <rutsky@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we are only explicitly setting SOCK_NOSPACE on a write timeout
for non-blocking sockets. Epoll() edge-trigger mode relies on SOCK_NOSPACE
being set when -EAGAIN is returned to ensure that EPOLLOUT is raised.
Expand the setting of SOCK_NOSPACE to non-blocking sockets as well that can
use SO_SNDTIMEO to adjust their write timeout. This mirrors the behavior
that Eric Dumazet introduced for tcp sockets.
Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Ursula Braun <ubraun@linux.ibm.com> Cc: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In certain cases when the probe function fails the error path calls
cpsw_remove_dt() before calling platform_set_drvdata(). This is an
issue as cpsw_remove_dt() uses platform_get_drvdata() to retrieve the
cpsw_common data and leds to a NULL pointer exception. This patches
fixes it by calling platform_set_drvdata() earlier in the probe.
Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization") Reported-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefano Brivio [Mon, 12 Aug 2019 22:46:01 +0000 (00:46 +0200)]
ipv6: Fix return value of ipv6_mc_may_pull() for malformed packets
Commit ba5ea614622d ("bridge: simplify ip_mc_check_igmp() and
ipv6_mc_check_mld() calls") replaces direct calls to pskb_may_pull()
in br_ipv6_multicast_mld2_report() with calls to ipv6_mc_may_pull(),
that returns -EINVAL on buffers too short to be valid IPv6 packets,
while maintaining the previous handling of the return code.
This leads to the direct opposite of the intended effect: if the
packet is malformed, -EINVAL evaluates as true, and we'll happily
proceed with the processing.
Return 0 if the packet is too short, in the same way as this was
fixed for IPv4 by commit 083b78a9ed64 ("ip: fix ip_mc_may_pull()
return value").
I don't have a reproducer for this, unlike the one referred to by
the IPv4 commit, but this is clearly broken.
Fixes: ba5ea614622d ("bridge: simplify ip_mc_check_igmp() and ipv6_mc_check_mld() calls") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Acked-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 93a714d6b53d ("multicast: Extend ip address command to enable
multicast group join/leave on") we added a new flag IFA_F_MCAUTOJOIN
to make user able to add multicast address on ethernet interface.
This works for IPv4, but not for IPv6. See the inet6_addr_add code.
static int inet6_addr_add()
{
...
if (cfg->ifa_flags & IFA_F_MCAUTOJOIN) {
ipv6_mc_config(net->ipv6.mc_autojoin_sk, true...)
}
ifp = ipv6_add_addr(idev, cfg, true, extack); <- always fail with maddr
if (!IS_ERR(ifp)) {
...
} else if (cfg->ifa_flags & IFA_F_MCAUTOJOIN) {
ipv6_mc_config(net->ipv6.mc_autojoin_sk, false...)
}
}
But in ipv6_add_addr() it will check the address type and reject multicast
address directly. So this feature is never worked for IPv6.
We should not remove the multicast address check totally in ipv6_add_addr(),
but could accept multicast address only when IFA_F_MCAUTOJOIN flag supplied.
v2: update commit description
Fixes: 93a714d6b53d ("multicast: Extend ip address command to enable multicast group join/leave on") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part
Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 5e6acc3e678e ("bcm2835-pm: Move bcm2835-watchdog's DT probe
to an MFD.") broke module autoloading on Raspberry Pi. So add a
module alias this fix this.
LTP mtest06 has been observed to occasionally hit "still mapped when
deleted" and following BUG_ON on arm64.
The extra mapcount originated from pagefault handler, which handled
pagefault for vma that has already been detached. vma is detached
under mmap_sem write lock by detach_vmas_to_be_unmapped(), which
also invalidates vmacache.
When the pagefault handler (under mmap_sem read lock) calls
find_vma(), vmacache_valid() wrongly reports vmacache as valid.
After rwsem down_read() returns via 'queue empty' path (as of v5.2),
it does so without an ACQUIRE on sem->count:
down_read()
__down_read()
rwsem_down_read_failed()
__rwsem_down_read_failed_common()
raw_spin_lock_irq(&sem->wait_lock);
if (list_empty(&sem->wait_list)) {
if (atomic_long_read(&sem->count) >= 0) {
raw_spin_unlock_irq(&sem->wait_lock);
return sem;
The problem can be reproduced by running LTP mtest06 in a loop and
building the kernel (-j $NCPUS) in parallel. It does reproduces since
v4.20 on arm64 HPE Apollo 70 (224 CPUs, 256GB RAM, 2 nodes). It
triggers reliably in about an hour.
The patched kernel ran fine for 10+ hours.
Signed-off-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Will Deacon <will@kernel.org> Acked-by: Waiman Long <longman@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dbueso@suse.de Fixes: 4b486b535c33 ("locking/rwsem: Exit read lock slowpath if queue empty & no writer") Link: https://lkml.kernel.org/r/50b8914e20d1d62bb2dee42d342836c2c16ebee7.1563438048.git.jstancek@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixed pep8/flake8 python style code for lsvmbus tool.
The TAB indentation was on purpose ignored (pep8 rule W191) to make
sure the code is complying with the Linux code guideline.
The following command doe not show any warnings now:
pep8 --ignore=W191 lsvmbus
flake8 --ignore=W191 lsvmbus
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sasha Levin <sashal@kernel.org> Cc: Dexuan Cui <decui@microsoft.com> Cc: Alessandro Pilotti <apilotti@cloudbasesolutions.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RISC-V kernel implementation of flush_tlb_page() when CONFIG_SMP
is set is wrong. It passes zero to flush_tlb_range() as the final
address to flush, but it should be at least 'addr'.
Some other Linux architecture ports use the beginning address to
flush, plus PAGE_SIZE, as the final address to flush. This might
flush slightly more than what's needed, but it seems unlikely that
being more clever would improve anything. So let's just take that
implementation for now.
While here, convert the macro into a static inline function, primarily
to avoid unintentional multiple evaluations of 'addr'.
This second version of the patch fixes a coding style issue found by
Christoph Hellwig <hch@lst.de>.
Reported-by: Andreas Schwab <schwab@suse.de> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a CPU doesn't support the page size for which the kernel is
configured, then we will complain and refuse to bring it online. For
secondary CPUs (and the boot CPU on a system booting with EFI), we will
also print an error identifying the mismatch.
Consequently, the only time that the cpufeature code can detect a
granule size mismatch is for a granule other than the one that is
currently being used. Although we would rather such systems didn't
exist, we've unfortunately lost that battle and Kevin reports that
on his amlogic S922X (odroid-n2 board) we end up warning and taining
with defconfig because 16k pages are not supported by all of the CPUs.
In such a situation, we don't actually care about the feature mismatch,
particularly now that KVM only exposes the sanitised view of the CPU
registers (commit 93390c0a1b20 - "arm64: KVM: Hide unsupported AArch64
CPU features from guests"). Treat the granule fields as non-strict and
let Kevin run without a tainted kernel.
Cc: Marc Zyngier <maz@kernel.org> Reported-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
[catalin.marinas@arm.com: changelog updated with KVM sanitised regs commit] Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In read_per_ring_refs(), after 'req' and related memory regions are
allocated, xen_blkif_map() is invoked to map the shared frame, irq, and
etc. However, if this mapping process fails, no cleanup is performed,
leading to memory leaks. To fix this issue, invoke the cleanup before
returning the error.
Acked-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When unmasking IRQs inside the ASIC, the driver passes an array of all the
IRQ to unmask. The ASIC's CPU is working in LE so when running in a BE
host, the driver needs to do the proper endianness swapping when preparing
this array.
In addition, this patch also fixes the endianness of a couple of kernel log
debug messages that print values of packets
The PQs of internal H/W queues (QMANs) can be located in different memory
areas for different ASICs. Therefore, when writing PQEs, we need to use
the correct function according to the location of the PQ. e.g. if the PQ
is located in the device's memory (SRAM or DRAM), we need to use
memcpy_toio() so it would work in architectures that have separate
address ranges for IO memory.
This patch makes the code that writes the PQE to be ASIC-specific so we
can handle this properly per ASIC.
This patch fix the CQ irq handler to work in hosts with BE architecture.
It adds the correct endian-swapping macros around the relevant memory
accesses.
Packets that arrive from the user and need to be parsed by the driver are
assumed to be in LE format.
This patch fix all the places where the code handles these packets and use
the correct endianness macros to handle them, as the driver handles the
packets in CPU format (LE or BE depending on the arch).
The patch fix the DRAM usage accounting by adding a missing update of
the DRAM memory consumption, when a context is being torn down without an
organized release of the allocated memory.
If fsg_disable() and fsg_set_alt() are called too closely to each
other (for example due to a quick reset/reconnect), what can happen
is that fsg_set_alt sets common->new_fsg from an interrupt while
handle_exception is trying to process the config change caused by
fsg_disable():
fsg_disable()
...
handle_exception()
sets state back to FSG_STATE_NORMAL
hasn't yet called do_set_interface()
or is inside it.
---> interrupt
fsg_set_alt
sets common->new_fsg
queues a new FSG_STATE_CONFIG_CHANGE
<---
Now, the first handle_exception can "see" the updated
new_fsg, treats it as if it was a fsg_set_alt() response,
call usb_composite_setup_continue() etc...
But then, the thread sees the second FSG_STATE_CONFIG_CHANGE,
and goes back down the same path, wipes and reattaches a now
active fsg, and .. calls usb_composite_setup_continue() which
at this point is wrong.
Not only we get a backtrace, but I suspect the second set_interface
wrecks some state causing the host to get upset in my case.
This fixes it by replacing "new_fsg" by a "state argument" (same
principle) which is set in the same lock section as the state
update, and retrieved similarly.
That way, there is never any discrepancy between the dequeued
state and the observed value of it. We keep the ability to have
the latest reconfig operation take precedence, but we guarantee
that once "dequeued" the argument (new_fsg) will not be clobbered
by any new event.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dma required_mask needs to reflect the actual addressing capabilities
needed to handle the whole system RAM. When truncated down to the bus
addressing capabilities dma_addressing_limited() will incorrectly signal
no limitations for devices which are restricted by the bus_dma_mask.
Since scatterlist dimensions are all unsigned ints, in the relatively
rare cases where a device's max_segment_size is set to UINT_MAX, then
the "cur_len + s_length <= max_len" check in __finalise_sg() will always
return true. As a result, the corner case of such a device mapping an
excessively large scatterlist which is mergeable to or beyond a total
length of 4GB can lead to overflow and a bogus truncated dma_length in
the resulting segment.
As we already assume that any single segment must be no longer than
max_len to begin with, this can easily be addressed by reshuffling the
comparison.
The OMAP 4 TRM specifies that when using double-index addressing
the address increases by the ES plus the EI value minus 1 within
a frame. When a full frame is transferred, the address increases
by the ES plus the frame index (FI) value minus 1.
The omap-dma code didn't account for the 'minus 1' in the FI register.
To get correct addressing, add 1 to the src_icg value.
This was found when testing a hacked version of the media m2m-deinterlace.c
driver on a Pandaboard.
The only other source that uses this feature is omap_vout_vrfb.c,
and that adds a + 1 when setting the dst_icg. This is a workaround
for the broken omap-dma.c behavior. So remove the workaround at the
same time that we fix omap-dma.c.
I tested the omap_vout driver with a Beagle XM board to check that
the '+ 1' in omap_vout_vrfb.c was indeed a workaround for the omap-dma
bug.
In stm32_mdma_irq_handler(), chan is checked on line 1368.
When chan is NULL, it is still used on line 1369:
dev_err(chan2dev(chan), "MDMA channel not initialized\n");
Thus, a possible null-pointer dereference may occur.
To fix this bug, "dev_dbg(mdma2dev(dmadev), ...)" is used instead.
Once implicit MR is being called to be released by
ib_umem_notifier_release() its leaves were marked as "dying".
However, when dereg_mr()->mlx5_ib_free_implicit_mr()->mr_leaf_free() is
called, it skips running the mr_leaf_free_action (i.e. umem_odp->work)
when those leaves were marked as "dying".
As such ib_umem_release() for the leaves won't be called and their MRs
will be leaked as well.
When an application exits/killed without calling dereg_mr we might hit the
above flow.
This fatal scenario is reported by WARN_ON() upon
mlx5_ib_dealloc_ucontext() as ibcontext->per_mm_list is not empty, the
call trace can be seen below.
Originally the "dying" mark as part of ib_umem_notifier_release() was
introduced to prevent pagefault_mr() from returning a success response
once this happened. However, we already have today the completion
mechanism so no need for that in those flows any more. Even in case a
success response will be returned the firmware will not find the pages and
an error will be returned in the following call as a released mm will
cause ib_umem_odp_map_dma_pages() to permanently fail mmget_not_zero().
Fix the above issue by dropping the "dying" from the above flows. The
other flows that are using "dying" are still needed it for their
synchronization purposes.
Ensure the controller is not in the NEW state when nvme_probe() exits.
This will always allow a subsequent nvme_remove() to set the state to
DELETING, fixing a potential race between the initial asynchronous probe
and device removal.
Reported-by: Li Zhong <lizhongfs@gmail.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org>
With multipath enabled, nvme_scan_work() can read from the device
(through nvme_mpath_add_disk()) and hang [1]. However, with fabrics,
once ctrl->state is set to NVME_CTRL_DELETING, the reads will hang
(see nvmf_check_ready()) and the mpath stack device make_request
will block if head->list is not empty. However, when the head->list
consistst of only DELETING/DEAD controllers, we should actually not
block, but rather fail immediately.
In addition, before we go ahead and remove the namespaces, make sure
to clear the current path and kick the requeue list so that the
request will fast fail upon requeuing.
[1]:
--
INFO: task kworker/u4:3:166 blocked for more than 120 seconds.
Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:3 D 0 166 2 0x80004000
Workqueue: nvme-wq nvme_scan_work
Call Trace:
__schedule+0x851/0x1400
schedule+0x99/0x210
io_schedule+0x21/0x70
do_read_cache_page+0xa57/0x1330
read_cache_page+0x4a/0x70
read_dev_sector+0xbf/0x380
amiga_partition+0xc4/0x1230
check_partition+0x30f/0x630
rescan_partitions+0x19a/0x980
__blkdev_get+0x85a/0x12f0
blkdev_get+0x2a5/0x790
__device_add_disk+0xe25/0x1250
device_add_disk+0x13/0x20
nvme_mpath_set_live+0x172/0x2b0
nvme_update_ns_ana_state+0x130/0x180
nvme_set_ns_ana_state+0x9a/0xb0
nvme_parse_ana_log+0x1c3/0x4a0
nvme_mpath_add_disk+0x157/0x290
nvme_validate_ns+0x1017/0x1bd0
nvme_scan_work+0x44d/0x6a0
process_one_work+0x7d7/0x1240
worker_thread+0x8e/0xff0
kthread+0x2c3/0x3b0
ret_from_fork+0x35/0x40
INFO: task kworker/u4:1:1034 blocked for more than 120 seconds.
Not tainted 5.2.0-rc6-vmlocalyes-00005-g808c8c2dc0cf #316
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:1 D 0 1034 2 0x80004000
Workqueue: nvme-delete-wq nvme_delete_ctrl_work
Call Trace:
__schedule+0x851/0x1400
schedule+0x99/0x210
schedule_timeout+0x390/0x830
wait_for_completion+0x1a7/0x310
__flush_work+0x241/0x5d0
flush_work+0x10/0x20
nvme_remove_namespaces+0x85/0x3d0
nvme_do_delete_ctrl+0xb4/0x1e0
nvme_delete_ctrl_work+0x15/0x20
process_one_work+0x7d7/0x1240
worker_thread+0x8e/0xff0
kthread+0x2c3/0x3b0
ret_from_fork+0x35/0x40
--
When start_queue fails, we need to make sure to drain the
queue cq before freeing the rdma resources because we might
still race with the completion path. Have start_queue() error
path safely stop the queue.
When the user issues a command with side effects, we will end up freezing
the namespace request queue when updating disk info (and the same for
the corresponding mpath disk node).
However, we are not freezing the mpath node request queue,
which means that mpath I/O can still come in and block on blk_queue_enter
(called from nvme_ns_head_make_request -> direct_make_request).
This is a deadlock, because blk_queue_enter will block until the inner
namespace request queue is unfroze, but that process is blocked because
the namespace revalidation is trying to update the mpath disk info
and freeze its request queue (which will never complete because
of the I/O that is blocked on blk_queue_enter).
Fix this by freezing all the subsystem nsheads request queues before
executing the passthru command. Given that these commands are infrequent
we should not worry about this temporary I/O freeze to keep things sane.
Presently, nvmet_file_flush() always returns a call to
errno_to_nvme_status() but that helper doesn't take into account the
case when errno=0. So nvmet_file_flush() always returns an error code.
All other callers of errno_to_nvme_status() check for success before
calling it.
To fix this, ensure errno_to_nvme_status() returns success if the
errno is zero. This should prevent future mistakes like this from
happening.
After calling nvme_loop_delete_ctrl(), the controllers will not
yet be deleted because nvme_delete_ctrl() only schedules work
to do the delete.
This means a race can occur if a port is removed but there
are still active controllers trying to access that memory.
To fix this, flush the nvme_delete_wq before returning from
nvme_loop_remove_port() so that any controllers that might
be in the process of being deleted won't access a freed port.
When a port is removed through configfs, any connected controllers
are still active and can still send commands. This causes a
use-after-free bug which is detected by KASAN for any admin command
that dereferences req->port (like in nvmet_execute_identify_ctrl).
To fix this, disconnect all active controllers when a subsystem is
removed from a port. This ensures there are no active controllers
when the port is eventually removed.
In the in-kernel afs filesystem, the d_fsdata dentry field is used to hold
the data version of the parent directory when it was created or when
d_revalidate() last caused it to be updated. This is compared to the
->invalid_before field in the directory inode, rather than the actual data
version number, thereby allowing changes due to local edits to be ignored.
Only if the server data version gets bumped unexpectedly (eg. by a
competing client), do we need to revalidate stuff.
However, the d_fsdata field should also be updated if an rpc op is
performed that modifies that particular dentry. Such ops return the
revised data version of the directory(ies) involved, so we should use that.
This is particularly problematic for rename, since a dentry from one
directory may be moved directly into another directory (ie. mv a/x b/x).
It would then be sporting the wrong data version - and if this is in the
future, for the destination directory, revalidations would be missed,
leading to foreign renames and hard-link deletion being missed.
Fix this by the following means:
(1) Return the data version number from operations that read the directory
contents - if they issue the read. This starts in afs_dir_iterate()
and is used, ignored or passed back by its callers.
(2) In afs_lookup*(), set the dentry version to the version returned by
(1) before d_splice_alias() is called and the dentry published.
(3) In afs_d_revalidate(), set the dentry version to that returned from
(1) if an rpc call was issued. This means that if a parallel
procedure, such as mkdir(), modifies the directory, we won't
accidentally use the data version from that.
(4) In afs_{mkdir,create,link,symlink}(), set the new dentry's version to
the directory data version before d_instantiate() is called.
(5) In afs_{rmdir,unlink}, update the target dentry's version to the
directory data version as soon as we've updated the directory inode.
(6) In afs_rename(), we need to unhash the old dentry before we start so
that we don't get afs_d_revalidate() reverting the version change in
cross-directory renames.
We then need to set both the old and the new dentry versions the data
version of the new directory before we call d_move() as d_move() will
rehash them.
In the in-kernel afs filesystem, d_fsdata is set with the data version of
the parent directory. afs_d_revalidate() will update this to the current
directory version, but it shouldn't do this if it the value it read from
d_fsdata is the same as no lock is held and cmpxchg() is not used.
Fix the code to only change the value if it is different from the current
directory version.
When afs_rename() calculates the expected data version of the target
directory in a cross-directory rename, it doesn't increment it as it
should, so it always thinks that the target inode is unexpectedly modified
on the server.
Fixes: a58823ac4589 ("afs: Fix application of status and callback to be under same lock") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In afs_read_dir(), there is an if statement on line 255 to check whether
req->pages is NULL:
if (!req->pages)
goto error;
If req->pages is NULL, afs_put_read() on line 337 is executed.
In afs_put_read(), req->pages[i] is used on line 195.
Thus, a possible null-pointer dereference may occur in this case.
To fix this possible bug, an if statement is added in afs_put_read() to
check req->pages.
This bug is found by a static analysis tool STCheck written by us.
Fixes: f3ddee8dc4e2 ("afs: Fix directory handling") Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
afs_deliver_vl_get_entry_by_name_u() scans through the vl entry
received from the volume location server and builds a return list
containing the sites that are currently valid. When assigning
values for the return list, the index into the vl entry (i) is used
rather than the one for the new list (entry->nr_server). If all
sites are usable, this works out fine as the indices will match.
If some sites are not valid, for example if AFS_VLSF_DONTUSE is
set, fs_mask and the uuid will be set for the wrong return site.
Fix this by using entry->nr_server as the index into the arrays
being filled in rather than i.
This can lead to EDESTADDRREQ errors if none of the returned sites
have a valid fs_mask.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the service handler function for the CB.ProbeUuid RPC call so that it
replies in the correct manner - that is an empty reply for success and an
abort of 1 for failure.
Putting 0 or 1 in an integer in the body of the reply should result in the
fileserver throwing an RX_PROTOCOL_ERROR abort and discarding its record of
the client; older servers, however, don't necessarily check that all the
data got consumed, and so might incorrectly think that they got a positive
response and associate the client with the wrong host record.
If the client is incorrectly associated, this will result in callbacks
intended for a different client being delivered to this one and then, when
the other client connects and responds positively, all of the callback
promises meant for the client that issued the improper response will be
lost and it won't receive any further change notifications.
Fixes: 9396d496d745 ("afs: support the CB.ProbeUuid RPC op") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_NVME_MULTIPATH is set, only the hidden gendisk associated
with the per-controller ns is run through revalidate_disk when a
rescan is triggered, while the visible blockdev never gets its size
(bdev->bd_inode->i_size) updated to reflect any capacity changes that
may have occurred.
This prevents online resizing of nvme block devices and in extension of
any filesystems atop that will are unable to expand while mounted, as
userspace relies on the blockdev size for obtaining the disk capacity
(via BLKGETSIZE/64 ioctls).
Fix this by explicitly revalidating the actual namespace gendisk in
addition to the per-controller gendisk, when multipath is enabled.
Signed-off-by: Anthony Iliopoulos <ailiopoulos@suse.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-9 points out that there are two variables that depending on the
configuration may only be used in an ARRAY_SIZE() expression but not
referenced:
drivers/dma/ste_dma40.c:145:12: error: variable 'd40_backup_regs' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs[] = {
^
drivers/dma/ste_dma40.c:214:12: error: variable 'd40_backup_regs_chan' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs_chan[] = {
When a local endpoint (struct rxrpc_local) ceases to be in use by any
AF_RXRPC sockets, it starts the process of being destroyed, but this
doesn't cause it to be removed from the namespace endpoint list immediately
as tearing it down isn't trivial and can't be done in softirq context, so
it gets deferred.
If a new socket comes along that wants to bind to the same endpoint, a new
rxrpc_local object will be allocated and rxrpc_lookup_local() will use
list_replace() to substitute the new one for the old.
Then, when the dying object gets to rxrpc_local_destroyer(), it is removed
unconditionally from whatever list it is on by calling list_del_init().
However, list_replace() doesn't reset the pointers in the replaced
list_head and so the list_del_init() will likely corrupt the local
endpoints list.
Fix this by using list_replace_init() instead.
Fixes: 730c5fd42c1e ("rxrpc: Fix local endpoint refcounting") Reported-by: syzbot+193e29e9387ea5837f1d@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log