Javier Carrasco [Wed, 23 Oct 2024 18:59:59 +0000 (20:59 +0200)]
iio: light: add support for veml3235
The Vishay veml3235 is a low-power ambient light sensor with I2C
interface. It provides a minimum detectable intensity of
0.0021 lx/cnt, configurable integration time and gain, and an additional
white channel to distinguish between different light sources.
Javier Carrasco [Wed, 23 Oct 2024 18:59:58 +0000 (20:59 +0200)]
dt-bindings: iio: light: veml6030: add veml3235
The veml3235 is another Vishay ambient light sensor that shares similar
properties with the other sensors covered by this bindings. In this
case, only the compatible, reg, and vdd-supply properties are required,
and the device does not have an interrupt line, like the already
supported veml7700.
Andy Shevchenko [Thu, 24 Oct 2024 19:05:12 +0000 (22:05 +0300)]
iio: light: ltr501: Add LTER0303 to the supported devices
It has been found that the (non-vendor issued) ACPI ID for Lite-On
LTR303 is present in Microsoft catalog. Add it to the list of the
supported devices.
Andy Shevchenko [Thu, 24 Oct 2024 19:05:11 +0000 (22:05 +0300)]
iio: light: ltr501: Drop most likely fake ACPI IDs
The commits in question do not proove that ACPI IDs exist.
Quite likely it was a cargo cult addition while doing that
for DT-based enumeration. Drop most likely fake ACPI IDs.
The to be removed IDs has been checked against the following resources:
1) DuckDuckGo
2) Google
3) MS catalog: https://www.catalog.update.microsoft.com/Search.aspx
This gives no useful results in regard to DSDT, moreover, the official
vendor ID in the registry for Lite-On is LCI.
Andy Shevchenko [Thu, 24 Oct 2024 19:05:10 +0000 (22:05 +0300)]
iio: light: isl29018: drop ACPI_PTR() and CONFIG_ACPI guards
The complexity of config guards needed for ACPI_PTR() is not worthwhile
for the small amount of saved data. This example was doing it correctly
but I am proposing dropping this so as to reduce chance of cut and paste
where it is done wrong. Also drop now unneeded linux/acpi.h include and
added linux/mod_devicetable.h for struct acpi_device_id definition.
Andy Shevchenko [Thu, 24 Oct 2024 19:05:05 +0000 (22:05 +0300)]
iio: accel: kxcjk-1013: drop ACPI_PTR() and move ID out of CONFIG_ACPI guards
The complexity of config guards needed for ACPI_PTR() is not worthwhile
for the small amount of saved data. This example was doing it correctly
but I am proposing dropping this so as to reduce chance of cut and paste
where it is done wrong. Also added linux/mod_devicetable.h for
struct acpi_device_id definition.
Andy Shevchenko [Thu, 24 Oct 2024 19:05:03 +0000 (22:05 +0300)]
iio: accel: kxcjk-1013: Get rid of enum kx_chipset
Instead of using enum, out of which only a couple of values
are being actually used, make a comparisons against pointer
to the respective chip_info structures.
Andy Shevchenko [Thu, 24 Oct 2024 19:04:57 +0000 (22:04 +0300)]
iio: accel: kxcjk-1013: Switch from CONFIG_PM guards to pm_ptr() etc
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Andy Shevchenko [Thu, 24 Oct 2024 19:04:56 +0000 (22:04 +0300)]
iio: accel: kxcjk-1013: Revert "Add support for KX022-1020"
The mentioned change effectively broke the ODR startup timeouts
settungs for KX023-1025 case. Let's revert it for now and see
how we can handle it with the better approach after switching
the driver to use data structure instead of enum.
Andy Shevchenko [Thu, 24 Oct 2024 19:04:52 +0000 (22:04 +0300)]
iio: imu: inv_mpu6050: Replace strange way of checking type of enumeration
When device is enumerated via ACPI the respective device node is of
ACPI device type. Use that to check for ACPI enumeration, rather than
calling for full match which is O(n) vs. O(1) for the regular check.
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://patch.msgid.link/20241024191200.229894-4-andriy.shevchenko@linux.intel.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Thu, 24 Oct 2024 19:04:51 +0000 (22:04 +0300)]
iio: adc: pac1934: Replace strange way of checking type of enumeration
When device is enumerated via ACPI the respective device node is of
ACPI device type. Use that to check for ACPI enumeration, rather than
calling for full match which is O(n) vs. O(1) for the regular check.
Alexandru Ardelean [Fri, 25 Oct 2024 09:59:39 +0000 (12:59 +0300)]
iio: adc: ad7606: add support for AD760{7,8,9} parts
The AD7607, AD7608 and AD7609 are some older parts of the AD7606 family.
They are hardware-only, meaning that they don't have any registers
accessible via SPI or Parallel interface.
They are more similar to the AD7605-4 part, which is supported by the
'ad7606' driver, and are configurable via GPIOs.
Like the AD7605-4 part, all 3 parts have 2 CONVST (Conversion Start) pins
(CONVST A and CONVST B). But in practice, these should be tied together to
make reading of samples easier via a serial line.
The AD7607 has an 14-bit resolution and AD7608 & AD7609 have an 18-bit
resolution. The main difference between the AD7608 & AD7609 is that the
AD7609 has a larger range (±10V & ±20V) vs the ±5V & ±10V ranges for AD7608.
However, unlike AD7605-4 part, these 3 parts have oversampling which is
configurable (like for the AD7606 in HW-mode) via GPIOs.
Alexandru Ardelean [Fri, 25 Oct 2024 09:59:37 +0000 (12:59 +0300)]
iio: adc: ad7606: rework scale-available to be static
The main driver for this change is the AD7607 part, which has a scale of
"1.220703" for the ±10V range. The AD7607 has a resolution of 14-bits.
So, just adding the scale-available list for that part would require some
quirks to handle just that scale value.
But to do it more neatly, the best approach is to rework the scale
available lists to have the same format as it is returned to userspace.
That way, we can also get rid of the allocation for the 'scale_avail_show'
array.
Alexandru Ardelean [Fri, 25 Oct 2024 09:59:36 +0000 (12:59 +0300)]
iio: adc: ad7606: use realbits for sign-extending in scan_direct
Currently the 'ad7606' driver supports parts with 18 and 16 bits
resolutions.
But when adding support for AD7607 (which has a 14-bit resolution) we
should check for the 'realbits' field, to be able to sign-extend correctly.
When the mutexes were reworked to guards, the caching of the
oversampling_ratio values was removed by accident.
The main effect of this change is that, after setting the
oversampling_ratio value, reading it back would result in the initial value
(of 1).
The value would get sent to the device correctly though.
Fixes 2956979dbd0d: ("iio: adc: ad7606: switch mutexes to guard")
Jonathan Cameron [Sun, 20 Oct 2024 18:07:20 +0000 (19:07 +0100)]
iio: accel: replace s64 __aligned(8) with aligned_s64
e4ca0e59c394 ("types: Complement the aligned types with signed 64-bit one")
introduced aligned_s64. Use it for all IIO accelerometer drivers.
Reviewed-by: Nuno Sa <nuno.sa@analog.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://patch.msgid.link/20241020180720.496327-1-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Emil Gedenryd [Thu, 3 Oct 2024 12:22:16 +0000 (14:22 +0200)]
dt-bindings: iio: light: opt3001: add compatible for opt3002
The opt3002 is a Light-to-Digital Sensor by TI with support for wide-range
spectrum light. It shares most properties with their opt3001 model with
the exception of having a wide spectral bandwidth, ranging from 300 nm
to 1000 nm.
Ramona Alexandra Nechita [Mon, 14 Oct 2024 14:32:00 +0000 (17:32 +0300)]
drivers: iio: adc: add support for ad777x family
Add support for AD7770, AD7771, AD7779 ADCs. The device is capable of
sending out data both on DOUT lines interface,as on the SDO line.
The driver currently implements only the SDO data streaming mode. SPI
communication is used alternatively for accessing registers and streaming
data. Register accesses are protected by crc8.
Ramona Alexandra Nechita [Mon, 14 Oct 2024 14:31:59 +0000 (17:31 +0300)]
Documentation: ABI: added filter mode doc in sysfs-bus-iio
The filter mode / filter type property is used for ad4130
and ad7779 drivers, therefore the ABI doc file for ad4130
was removed, merging both of them in the sysfs-bus-iio.
Since one of the drivers is available from 6.1, the version
has been set to 6.1 for these attributes.
Ramona Alexandra Nechita [Mon, 14 Oct 2024 14:31:58 +0000 (17:31 +0300)]
dt-bindings: iio: adc: add ad7779 doc
Add dt bindings for AD7779 8-channel, simultaneous sampling ADC
family with eight full Σ-Δ ADCs on chip and ultra-low input
current to allow direct sensor connection.
Guillaume Stols [Tue, 15 Oct 2024 13:56:21 +0000 (13:56 +0000)]
iio: adc: ad7606: Disable PWM usage for non backend version
Since the pwm was introduced before backend, there was a mock use, with
a GPIO emulation. Now that iio backend is introduced, the mock use can
be removed.
Guillaume Stols [Tue, 15 Oct 2024 13:56:20 +0000 (13:56 +0000)]
iio: adc: ad7606: Add iio-backend support
- Basic support for iio backend.
- Supports IIO_CHAN_INFO_SAMP_FREQ R/W.
- Only hardware mode is available, and that IIO_CHAN_INFO_RAW is not
supported if iio-backend mode is selected.
Guillaume Stols [Tue, 15 Oct 2024 13:56:19 +0000 (13:56 +0000)]
iio: adc: ad7606: Introduce num_adc_channels
This variable determines how many hardware channels has the chip,
oppositely to the num_channels that can contain more channels, e.g a
timestamp channel in our case. Introducing this variable avoids
decreasing the former num_channels variable when reading the ADC's
channels, and clarifies a bit the code.
Guillaume Stols [Tue, 15 Oct 2024 13:56:18 +0000 (13:56 +0000)]
iio: adc: ad7606: Add compatibility to fw_nodes
On the parallel version, the current implementation is only compatible
with id tables and won't work with fw_nodes, this commit intends to fix
it.
Doing so required to declare ad7606_chip_info structures in the .h file
so to make them accessible to all the driver files that can set a
pointer to the corresponding chip as the driver data.
Guillaume Stols [Tue, 15 Oct 2024 13:56:17 +0000 (13:56 +0000)]
iio: adc: ad7606: Add PWM support for conversion trigger
Until now, the conversion were triggered by setting high the GPIO
connected to the convst pin. This commit gives the possibility to
connect the convst pin to a PWM.
Connecting a PWM allows to have a better control on the samplerate,
but it must be handled with care, as it is completely decorrelated of
the driver's busy pin handling.
Hence it is not recommended to be used "as is" but must be exploited
in conjunction with IIO backend, and for now only a mock functionality
is enabled, i.e PWM never swings, but is used as a GPIO, i.e duty_cycle
== period equals high state, duty_cycle == 0 equals low state.
This mock functionality will be disabled after the IIO backend usecase
is introduced.
Add the required properties for iio-backend support, as well as an
example and the conditions to mutually exclude interruption and
conversion trigger with iio-backend.
The iio-backend's function is to controls the communication, and thus the
interruption pin won't be available anymore.
As a consequence, the conversion pin must be controlled externally since
we will miss information about when every single conversion cycle (i.e
conversion + data transfer) ends, hence a PWM is introduced to trigger
the conversions.
Guillaume Stols [Tue, 15 Oct 2024 13:56:14 +0000 (13:56 +0000)]
dt-bindings: iio: adc: ad7606: Remove spi-cpha from required
The documentation is erroneously stating that spi-cpha is required, and
the example is erroneously setting both spi-cpol and spi-cpha. According
to the datasheet, only cpol should be set.
On zedboard for instance, setting the devicetree as in the example will
simply not work.
Fixes: 416f882c3b40 ("dt-bindings: iio: adc: Migrate AD7606 documentation to yaml") Fixes: 6e33a125df66 ("dt-bindings: iio: adc: Add docs for AD7606 ADC") Reviewed-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Guillaume Stols <gstols@baylibre.com> Link: https://patch.msgid.link/20241015-ad7606_add_iio_backend_support-v5-1-654faf1ae08c@baylibre.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nuno Sa [Wed, 16 Oct 2024 14:22:00 +0000 (16:22 +0200)]
iio: addac: ad74413r: use devm_regulator_get_enable_read_voltage()
It's highly unlikely for the converter ref voltage to change at runtime.
Hence, let's read the voltage and save it (instead of the regulator
struct). While at it, simplify the code by using
devm_regulator_get_enable_read_voltage().
Nuno Sa [Wed, 16 Oct 2024 14:21:59 +0000 (16:21 +0200)]
iio: addac: ad74413r: drop reset_gpio from struct ad74413r_state
We just need the reset gpio during probe so there's no need to keep it
in our state struct. Hence, move devm_gpiod_get_optional() into
ad74413r_reset() and use a local struct gpio_desc.
While at it, request the gpio in the asserted state (GPIOD_OUT_HIGH) so
that we already perform the reset while requesting the gpio saving us a
call to gpiod_set_value_cansleep().
Also, explicitly include <gpio/consumer.h> for
devm_gpiod_get_optional().
Javier Carrasco [Thu, 17 Oct 2024 21:39:26 +0000 (23:39 +0200)]
iio: light: veml6070: use field to set integration time
Define the integration time within the configuration register as a field
to easy its handling as an index, preparing the driver to support
configurable integration times.
Vasileios Amoiridis [Thu, 17 Oct 2024 23:30:19 +0000 (01:30 +0200)]
iio: pressure: bmp280: Use sleep and forced mode for oneshot captures
Add forced mode support in sensors BMP28x, BME28x, BMP3xx and BMP58x.
Sensors BMP18x and BMP085 are old and do not support this feature so
their operation is not affected at all.
Essentially, up to now, the rest of the sensors were used in normal mode
all the time. This means that they are continuously doing measurements
even though these measurements are not used. Even though the sensor does
provide PM support, to cover all the possible use cases, the sensor needs
to go into sleep mode and wake up whenever necessary.
The idea is that the sensor is by default in sleep mode, wakes up in
forced mode when a oneshot capture is requested, or in normal mode
when the buffer is enabled. The difference lays in the fact that in
forced mode, the sensor does only one conversion and goes back to sleep
while in normal mode, the sensor does continuous measurements with the
frequency that was set in the ODR registers.
The bmpX_chip_config() functions which are responsible for applying
the requested configuration to the sensor, are modified accordingly
in order to set the sensor by default in sleep mode.
DEEP STANDBY, Low Power NORMAL and CONTINUOUS modes, supported only by
the BMP58x version, are not added.
Andy Shevchenko [Fri, 18 Oct 2024 14:58:05 +0000 (17:58 +0300)]
iio: magnetometer: bmc150_magn: Drop most likely fake ACPI IDs
The commits in question do not proove that ACPI IDs exist.
Quite likely it was a cargo cult addition while doing that
for DT-based enumeration. Drop most likely fake ACPI IDs.
The to be removed IDs has been checked against the following resources:
1) DuckDuckGo
2) Google
3) MS catalog: https://www.catalog.update.microsoft.com/Search.aspx
This gives no useful results in regard to DSDT, moreover, the official
vendor IDs in the registry for Bosh are BSG and BOSC.
Andy Shevchenko [Fri, 18 Oct 2024 14:57:32 +0000 (17:57 +0300)]
iio: gyro: bmg160: Drop most likely fake ACPI IDs
The commits in question do not proove that ACPI IDs exist.
Quite likely it was a cargo cult addition while doing that
for DT-based enumeration. Drop most likely fake ACPI IDs.
The to be removed IDs has been checked against the following resources:
1) DuckDuckGo
2) Google
3) MS catalog: https://www.catalog.update.microsoft.com/Search.aspx
This gives no useful results in regard to DSDT, moreover, the official
vendor IDs in the registry for Bosh are BSG and BOSC.
Shen Jianping [Fri, 18 Oct 2024 13:52:34 +0000 (15:52 +0200)]
iio: imu: smi240: add driver
add the iio driver for bosch imu smi240. The smi240 is a combined
three axis angular rate and three axis acceleration sensor module
with a measurement range of +/-300°/s and up to 16g. A synchronous
acc and gyro sampling can be triggered by setting the capture bit
in spi read command.
Implemented features:
* raw data access for each axis through sysfs
* tiggered buffer for continuous sampling
* synchronous acc and gyro data from tiggered buffer
Linus Torvalds [Sun, 20 Oct 2024 21:08:17 +0000 (14:08 -0700)]
Merge tag 'for-net-2024-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Pull bluetooth fixes from Luiz Augusto Von Dentz:
- ISO: Fix multiple init when debugfs is disabled
- Call iso_exit() on module unload
- Remove debugfs directory on module init failure
- btusb: Fix not being able to reconnect after suspend
- btusb: Fix regression with fake CSR controllers 0a12:0001
- bnep: fix wild-memory-access in proto_unregister
Note: normally the bluetooth fixes go through the networking tree, but
this missed the weekly merge, and two of the commits fix regressions
that have caused a fair amount of noise and have now hit stable too:
So I'm pulling it directly just to expedite things and not miss yet
another -rc release. This is not meant to become a new pattern.
* tag 'for-net-2024-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: Fix regression with fake CSR controllers 0a12:0001
Bluetooth: bnep: fix wild-memory-access in proto_unregister
Bluetooth: btusb: Fix not being able to reconnect after suspend
Bluetooth: Remove debugfs directory on module init failure
Bluetooth: Call iso_exit() on module unload
Bluetooth: ISO: Fix multiple init when debugfs is disabled
Linus Torvalds [Sun, 20 Oct 2024 20:55:46 +0000 (13:55 -0700)]
Merge tag 'pinctrl-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Mostly error path fixes, but one pretty serious interrupt problem in
the Ocelot driver as well:
- Fix two error paths and a missing semicolon in the Intel driver
- Add a missing ACPI ID for the Intel Panther Lake
- Check return value of devm_kasprintf() in the Apple and STM32
drivers
- Add a missing mutex_destroy() in the aw9523 driver
- Fix a double free in cv1800_pctrl_dt_node_to_map() in the Sophgo
driver
- Fix a double free in ma35_pinctrl_dt_node_to_map_func() in the
Nuvoton driver
- Fix a bug in the Ocelot interrupt handler making the system hang"
* tag 'pinctrl-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: ocelot: fix system hang on level based interrupts
pinctrl: nuvoton: fix a double free in ma35_pinctrl_dt_node_to_map_func()
pinctrl: sophgo: fix double free in cv1800_pctrl_dt_node_to_map()
pinctrl: intel: platform: Add Panther Lake to the list of supported
pinctrl: aw9523: add missing mutex_destroy
pinctrl: stm32: check devm_kasprintf() returned value
pinctrl: apple: check devm_kasprintf() returned value
pinctrl: intel: platform: use semicolon instead of comma in ncommunities assignment
pinctrl: intel: platform: fix error path in device_for_each_child_node()
Linus Torvalds [Sun, 20 Oct 2024 20:10:44 +0000 (13:10 -0700)]
Merge tag 'char-misc-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver fixes from Greg KH:
"Here are a number of small char/misc/iio driver fixes for 6.12-rc4:
- loads of small iio driver fixes for reported problems
- parport driver out-of-bounds fix
- Kconfig description and MAINTAINERS file updates
All of these, except for the Kconfig and MAINTAINERS file updates have
been in linux-next all week. Those other two are just documentation
changes and will have no runtime issues and were merged on Friday"
* tag 'char-misc-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (39 commits)
misc: rtsx: list supported models in Kconfig help
MAINTAINERS: Remove some entries due to various compliance requirements.
misc: microchip: pci1xxxx: add support for NVMEM_DEVID_AUTO for OTP device
misc: microchip: pci1xxxx: add support for NVMEM_DEVID_AUTO for EEPROM device
parport: Proper fix for array out-of-bounds access
iio: frequency: admv4420: fix missing select REMAP_SPI in Kconfig
iio: frequency: {admv4420,adrf6780}: format Kconfig entries
iio: adc: ad4695: Add missing Kconfig select
iio: adc: ti-ads8688: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: hid-sensors: Fix an error handling path in _hid_sensor_set_report_latency()
iioc: dac: ltc2664: Fix span variable usage in ltc2664_channel_config()
iio: dac: stm32-dac-core: add missing select REGMAP_MMIO in Kconfig
iio: dac: ltc1660: add missing select REGMAP_SPI in Kconfig
iio: dac: ad5770r: add missing select REGMAP_SPI in Kconfig
iio: amplifiers: ada4250: add missing select REGMAP_SPI in Kconfig
iio: frequency: adf4377: add missing select REMAP_SPI in Kconfig
iio: resolver: ad2s1210: add missing select (TRIGGERED_)BUFFER in Kconfig
iio: resolver: ad2s1210 add missing select REGMAP in Kconfig
iio: proximity: mb1232: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
iio: pressure: bm1390: add missing select IIO_(TRIGGERED_)BUFFER in Kconfig
...
Linus Torvalds [Sun, 20 Oct 2024 19:57:53 +0000 (12:57 -0700)]
Merge tag 'usb-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes and new device ids for 6.12-rc4:
- xhci driver fixes for a number of reported issues
- new usb-serial driver ids
- dwc3 driver fixes for reported problems.
- usb gadget driver fixes for reported problems
- typec driver fixes
- MAINTAINER file updates
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Telit FN920C04 MBIM compositions
USB: serial: option: add support for Quectel EG916Q-GL
xhci: dbc: honor usb transfer size boundaries.
usb: xhci: Fix handling errors mid TD followed by other errors
xhci: Mitigate failed set dequeue pointer commands
xhci: Fix incorrect stream context type macro
USB: gadget: dummy-hcd: Fix "task hung" problem
usb: gadget: f_uac2: fix return value for UAC2_ATTRIBUTE_STRING store
usb: dwc3: core: Fix system suspend on TI AM62 platforms
xhci: tegra: fix checked USB2 port number
usb: dwc3: Wait for EndXfer completion before restoring GUSB2PHYCFG
usb: typec: qcom-pmic-typec: fix sink status being overwritten with RP_DEF
usb: typec: altmode should keep reference to parent
MAINTAINERS: usb: raw-gadget: add bug tracker link
MAINTAINERS: Add an entry for the LJCA drivers
Linus Torvalds [Sun, 20 Oct 2024 19:04:32 +0000 (12:04 -0700)]
Merge tag 'x86_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Explicitly disable the TSC deadline timer when going idle to address
some CPU errata in that area
- Do not apply the Zenbleed fix on anything else except AMD Zen2 on the
late microcode loading path
- Clear CPU buffers later in the NMI exit path on 32-bit to avoid
register clearing while they still contain sensitive data, for the
RDFS mitigation
- Do not clobber EFLAGS.ZF with VERW on the opportunistic SYSRET exit
path on 32-bit
- Fix parsing issues of memory bandwidth specification in sysfs for
resctrl's memory bandwidth allocation feature
- Other small cleanups and improvements
* tag 'x86_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Always explicitly disarm TSC-deadline timer
x86/CPU/AMD: Only apply Zenbleed fix for Zen2 during late microcode load
x86/bugs: Use code segment selector for VERW operand
x86/entry_32: Clear CPU buffers after register restore in NMI return
x86/entry_32: Do not clobber user EFLAGS.ZF
x86/resctrl: Annotate get_mem_config() functions as __init
x86/resctrl: Avoid overflow in MB settings in bw_validate()
x86/amd_nb: Add new PCI ID for AMD family 1Ah model 20h
Linus Torvalds [Sun, 20 Oct 2024 18:30:56 +0000 (11:30 -0700)]
Merge tag 'sched_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduling fixes from Borislav Petkov:
- Add PREEMPT_RT maintainers
- Fix another aspect of delayed dequeued tasks wrt determining their
state, i.e., whether they're runnable or blocked
- Handle delayed dequeued tasks and their migration wrt PSI properly
- Fix the situation where a delayed dequeue task gets enqueued into a
new class, which should not happen
- Fix a case where memory allocation would happen while the runqueue
lock is held, which is a no-no
- Do not over-schedule when tasks with shorter slices preempt the
currently running task
- Make sure delayed to deque entities are properly handled before
unthrottling
- Other smaller cleanups and improvements
* tag 'sched_urgent_for_v6.12_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Add an entry for PREEMPT_RT.
sched/fair: Fix external p->on_rq users
sched/psi: Fix mistaken CPU pressure indication after corrupted task state bug
sched/core: Dequeue PSI signals for blocked tasks that are delayed
sched: Fix delayed_dequeue vs switched_from_fair()
sched/core: Disable page allocation in task_tick_mm_cid()
sched/deadline: Use hrtick_enabled_dl() before start_hrtick_dl()
sched/eevdf: Fix wakeup-preempt by checking cfs_rq->nr_running
sched: Fix sched_delayed vs cfs_bandwidth
Linus Torvalds [Sun, 20 Oct 2024 00:04:52 +0000 (17:04 -0700)]
Merge tag 'io_uring-6.12-20241019' of git://git.kernel.dk/linux
Pull one more io_uring fix from Jens Axboe:
"Fix for a regression introduced in 6.12-rc2, where a condition check
was negated and hence -EAGAIN would bubble back up up to userspace
rather than trigger a retry condition"
* tag 'io_uring-6.12-20241019' of git://git.kernel.dk/linux:
io_uring/rw: fix wrong NOWAIT check in io_rw_init_file()
Linus Torvalds [Sat, 19 Oct 2024 19:52:19 +0000 (12:52 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Fixes all in drivers. The largest is the mpi3mr which corrects a phy
count limit that should only apply to the controller but was being
incorrectly applied to expander phys"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: core: Fix null-ptr-deref in target_alloc_device()
scsi: mpi3mr: Validate SAS port assignments
scsi: ufs: core: Set SDEV_OFFLINE when UFS is shut down
scsi: ufs: core: Requeue aborted request
scsi: ufs: core: Fix the issue of ICU failure
Linus Torvalds [Sat, 19 Oct 2024 19:42:14 +0000 (12:42 -0700)]
Merge tag 'ftrace-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull ftrace fixes from Steven Rostedt:
"A couple of fixes to function graph infrastructure:
- Fix allocation of idle shadow stack allocation during hotplug
If function graph tracing is started when a CPU is offline, if it
were come online during the trace then the idle task that
represents the CPU will not get a shadow stack allocated for it.
This means all function graph hooks that happen while that idle
task is running (including in interrupt mode) will have all its
events dropped.
Switch over to the CPU hotplug mechanism that will have any newly
brought on line CPU get a callback that can allocate the shadow
stack for its idle task.
- Fix allocation size of the ret_stack_list array
When function graph tracing converted over to allowing more than
one user at a time, it had to convert its shadow stack from an
array of ret_stack structures to an array of unsigned longs. The
shadow stacks are allocated in batches of 32 at a time and assigned
to every running task. The batch is held by the ret_stack_list
array.
But when the conversion happened, instead of allocating an array of
32 pointers, it was allocated as a ret_stack itself (PAGE_SIZE).
This ret_stack_list gets passed to a function that iterates over
what it believes is its size defined by the
FTRACE_RETSTACK_ALLOC_SIZE macro (which is 32).
Luckily (PAGE_SIZE) is greater than 32 * sizeof(long), otherwise
this would have been an array overflow. This still should be fixed
and the ret_stack_list should be allocated to the size it is
expected to be as someday it may end up being bigger than
SHADOW_STACK_SIZE"
* tag 'ftrace-v6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
fgraph: Allocate ret_stack_list with proper size
fgraph: Use CPU hotplug mechanism to initialize idle shadow stacks
projects / users / jedix / linux-maple.git / log