The code did not de-assert any CS GPIOs before probing slaves. This
means that several CS signals could be active at once, garbling the
communication. Whether this was actually a problem depended on the type
of the SPI device attached (so my "spidev" for userspace access worked
correctly because its probe was effectively a no-op), and on the state
of the GPIO pins at SoC's boot.
The code was already iterating through all DT children of the SPI
controller, so this change re-uses that loop for CS GPIO setup as well.
This means that this might change the number of the HW CS signal which
is picked for all GPIO CS devices. Previously, the lowest one was used,
but we now use the first one from the DT.
With this move of the code, we can also finally initialize each GPIO CS
lane before registering the SPI controller (which in turn probes for
slaves).
I tried to fix this in 544248623b95 already, but that only did it half
way by registering the GPIOs properly. That patch failed to set their
logic signals early enough, though.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possible conflict when a device is removed and host reset occurs
concurrently.
The reason is that then the device is notified as gone, we try to clear the
ITCT, which is notified via an interrupt. The dev gone function pends on
this event with a completion, which is completed when the ITCT interrupt
occurs.
But host reset will disable all interrupts, the wait_for_completion() may
wait indefinitely.
This patch adds an semaphore to synchronise this two processes. The
semaphore is taken by the host reset as the basis of synchronising.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xfstest generic/240, applications seem to expect direct I/O
writes to either complete as a whole or to fail; short direct I/O writes
are apparently not appreciated. This means that when only part of an
asynchronous direct I/O write succeeds, we can either fail the entire
write, or we can wait for the partial write to complete and retry the
remaining write as buffered I/O. The old __blockdev_direct_IO helper
has code for waiting for partial writes to complete; the new
iomap_dio_rw iomap helper does not.
The above mentioned fallback mode is needed for gfs2, which doesn't
allow block allocations under direct I/O to avoid taking cluster-wide
exclusive locks. As a consequence, an asynchronous direct I/O write to
a file range that contains a hole will result in a short write. In that
case, wait for the short write to complete to allow gfs2 to recover.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LBR has a limited stack size. If a task has a deeper call stack than
LBR's stack size, only the overflowed part is reported. A complete call
stack may not be reconstructed by perf tool.
Current code doesn't access all LBR registers. It only read the ones
below the TOS. The LBR registers above the TOS will be discarded
unconditionally.
When a CALL is captured, the TOS is incremented by 1 , modulo max LBR
stack size. The LBR HW only records the call stack information to the
register which the TOS points to. It will not touch other LBR
registers. So the registers above the TOS probably still store the valid
call stack information for an overflowed call stack, which need to be
reported.
To retrieve complete call stack information, we need to start from TOS,
read all LBR registers until an invalid entry is detected.
0s can be used to detect the invalid entry, because:
- When a RET is captured, the HW zeros the LBR register which TOS points
to, then decreases the TOS.
- The LBR registers are reset to 0 when adding a new LBR event or
scheduling an existing LBR event.
- A taken branch at IP 0 is not expected
The context switch code is also modified to save/restore all valid LBR
registers. Furthermore, the LBR registers, which don't have valid call
stack information, need to be reset in restore, because they may be
polluted while swapped out.
Here is a small test program, tchain_deep.
Its call stack is deeper than 32.
noinline void f33(void)
{
int i;
for (i = 0; i < 10000000;) {
if (i%2)
i++;
else
i++;
}
}
noinline void f32(void)
{
f33();
}
noinline void f31(void)
{
f32();
}
... ...
noinline void f1(void)
{
f2();
}
int main()
{
f1();
}
Here is the test result on SKX. The max stack size of SKX is 32.
Between creation and queueing of a job, you need to prevent any other
job from being created and queued. Otherwise the scheduler's fences
may be signaled out of seqno order.
v2: move mutex unlock to the error label.
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 57692c94dcbe ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+") Link: https://patchwork.freedesktop.org/patch/msgid/20180606174851.12433-1-eric@anholt.net Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VSPD and FCPVD nodes have overlapping register ranges, as the FCPVD
devices are mapped in the memory range usually used by the VSP LUT and
CLU, which are not present in the VSPD. Fix this by shortening the VSPD
registers range to 0x5000.
As Documentation/kbuild/makefile.txt says, it is a typical mistake
to forget the FORCE prerequisite for the rule invoked by if_changed.
Add the FORCE to the prerequisite, but it must be filtered-out from
the files passed to the 'cat' command. Because this rule generates
.vmlinux.its.S.cmd, vmlinux.its.S must be specified as targets so
that the .cmd file is included.
Use devm here to save some lines and prepare for bulk regulator usage in
this driver. Otherwise, when we devm bulk get regulators we'll free the
containing i2c_hid structure and try to put regulator pointers from
freed memory.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Dmitry Torokhov <dtor@chromium.org> Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
arch_validate_hwbkpt_settings() mixes up attribute check and commit into
a single code entity. Therefore the validation may return an error due to
incorrect atributes while still leaving halfway modified architecture
breakpoint data.
This is harmless when we deal with a new breakpoint but it becomes a
problem when we modify an existing breakpoint.
Split attribute parse and commit to fix that. The architecture is
passed a "struct arch_hw_breakpoint" to fill on top of the new attr
and the core takes care about copying the backend data once it's fully
validated. The architectures then need to implement the new API.
Original-patch-by: Andy Lutomirski <luto@kernel.org> Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chris Zankel <chris@zankel.net> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Joel Fernandes <joel.opensrc@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rich Felker <dalias@libc.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Link: http://lkml.kernel.org/r/1529981939-8231-2-git-send-email-frederic@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Number of specs is provided by user and in valid case can be equal to zero.
Such argument causes to call to kcalloc() with zero-length request and in
return the ZERO_SIZE_PTR is assigned. This pointer is different from NULL
and makes various if (..) checks to success.
Fixes: b6ba4a9aa59f ("IB/uverbs: Add support for flow counters") Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_FORTIFY_SOURCE, memcpy uses the declared size of operands to
detect buffer overflows. If src or dest is declared as a char, attempts to
copy more than byte will result in a fortify_panic().
Address this problem in mvebu_setup_boot_addr_wa() by declaring
mvebu_boot_wa_start and mvebu_boot_wa_end as character arrays. Also remove
a couple addressof operators to avoid "arithmetic on pointer to an
incomplete type" compiler error.
See commit 54a7d50b9205 ("x86: mark kprobe templates as character arrays,
not single characters") for a similar fix.
Fixes "detected buffer overflow in memcpy" error during init on some mvebu
systems (armada-370-xp, armada-375):
(fortify_panic) from (mvebu_setup_boot_addr_wa+0xb0/0xb4)
(mvebu_setup_boot_addr_wa) from (mvebu_v7_cpu_pm_init+0x154/0x204)
(mvebu_v7_cpu_pm_init) from (do_one_initcall+0x7c/0x1a8)
(do_one_initcall) from (kernel_init_freeable+0x1bc/0x254)
(kernel_init_freeable) from (kernel_init+0x8/0x114)
(kernel_init) from (ret_from_fork+0x14/0x2c)
- Switch to a mutex since the list walking at device resume time can
sleep when pinning buffers through the tiler.
Only thing we need to be careful with here is that while we walk the
list we can't unreference any gem objects, since the final unref would
result in a recursive deadlock. But the only functions that walk the
list is the device resume and debugfs dumping, so all safe.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84
I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bug in *_encode_bits() in using ~field_multiplier() for
the check whether or not the constant value fits into the field,
this is wrong and clearly ~field_mask() was intended. This was
triggering for me for both constant and non-constant values.
Additionally, make this case actually into an compile error.
Declaring the extern function that will never exist with just a
warning is pointless as then later we'll just get a link error.
While at it, also fix the indentation in those lines I'm touching.
Finally, as suggested by Andy Shevchenko, add some tests and for
that introduce also u8 helpers. The tests don't compile without
the fix, showing that it's necessary.
Fixes: 00b0c9b82663 ("Add primitives for manipulating bitfields both in host- and fixed-endian.") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9f9 ("brcmsmac: fix array out-of-bounds access in qm_log10") Cc: Tobias Regnery <tobias.regnery@gmail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a static checker fix, not something I have tested. The issue
is that on the second iteration through the loop, we jump forward by
le32_to_cpu(auth_req->length) bytes. The problem is that if the length
is more than "buflen" then we end up with a negative "buflen". A
negative buflen is type promoted to a high positive value and the loop
continues but it's accessing beyond the end of the buffer.
I believe the "auth_req->length" comes from the firmware and if the
firmware is malicious or buggy, you're already toasted so the impact of
this bug is probably not very severe.
Fixes: 030645aceb3d ("rndis_wlan: handle 802.11 indications from device") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix mcs and attempt count estimation in mt76x2_mac_fill_tx_status routine
if the number of tx retries reported by the hw is grater than
IEEE80211_TX_MAX_RATES
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are frames in the ieee80211_txq and there are frames that have
been removed from from this queue, but haven't yet been sent on the wire
(num_pending_tx).
When num_pending_tx reaches max_num_pending_tx, we will stop the queues
by calling ieee80211_stop_queues().
As frames that have previously been sent for transmission
(num_pending_tx) are completed, we will decrease num_pending_tx and wake
the queues by calling ieee80211_wake_queue(). ieee80211_wake_queue()
does not call wake_tx_queue, so we might still have frames in the
queue at this point.
While the queues were stopped, the socket buffer might have filled up,
and in order for user space to write more, we need to free the frames
in the queue, since they are accounted to the socket. In order to free
them, we first need to transmit them.
This problem cannot be reproduced on low-latency devices, e.g. pci,
since they call ath10k_mac_tx_push_pending() from
ath10k_htt_txrx_compl_task(). ath10k_htt_txrx_compl_task() is not called
on high-latency devices.
Fix the problem by calling ath10k_mac_tx_push_pending(), after
processing rx packets, just like for low-latency devices, also in the
SDIO case. Since we are calling ath10k_mac_tx_push_pending() directly,
we also need to export it.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since a phy_device is added to the global mdio_bus list during
phy_device_register(), but a phy_device's phy_driver doesn't get
attached until phy_probe(). It's possible of_phy_find_device() in
xgmiitorgmii will return a valid phy with a NULL phy_driver. Leading to
a NULL pointer access during the memcpy().
Fixes this Oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.40 #1
Hardware name: Xilinx Zynq Platform
task: ce4c8d00 task.stack: ce4ca000
PC is at memcpy+0x48/0x330
LR is at xgmiitorgmii_probe+0x90/0xe8
pc : [<c074bc68>] lr : [<c0529548>] psr: 20000013
sp : ce4cbb54 ip : 00000000 fp : ce4cbb8c
r10: 00000000 r9 : 00000000 r8 : c0c49178
r7 : 00000000 r6 : cdc14718 r5 : ce762800 r4 : cdc14710
r3 : 00000000 r2 : 00000054 r1 : 00000000 r0 : cdc14718
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 18c5387d Table: 0000404a DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0xce4ca210)
...
[<c074bc68>] (memcpy) from [<c0529548>] (xgmiitorgmii_probe+0x90/0xe8)
[<c0529548>] (xgmiitorgmii_probe) from [<c0526a94>] (mdio_probe+0x28/0x34)
[<c0526a94>] (mdio_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbd58>] (__device_attach_driver+0xac/0x10c)
[<c04dbd58>] (__device_attach_driver) from [<c04d96f4>] (bus_for_each_drv+0x84/0xc8)
[<c04d96f4>] (bus_for_each_drv) from [<c04db5bc>] (__device_attach+0xd0/0x134)
[<c04db5bc>] (__device_attach) from [<c04dbdd4>] (device_initial_probe+0x1c/0x20)
[<c04dbdd4>] (device_initial_probe) from [<c04da8fc>] (bus_probe_device+0x98/0xa0)
[<c04da8fc>] (bus_probe_device) from [<c04d8660>] (device_add+0x43c/0x5d0)
[<c04d8660>] (device_add) from [<c0526cb8>] (mdio_device_register+0x34/0x80)
[<c0526cb8>] (mdio_device_register) from [<c0580b48>] (of_mdiobus_register+0x170/0x30c)
[<c0580b48>] (of_mdiobus_register) from [<c05349c4>] (macb_probe+0x710/0xc00)
[<c05349c4>] (macb_probe) from [<c04dd700>] (platform_drv_probe+0x44/0x80)
[<c04dd700>] (platform_drv_probe) from [<c04db98c>] (driver_probe_device+0x254/0x414)
[<c04db98c>] (driver_probe_device) from [<c04dbc58>] (__driver_attach+0x10c/0x118)
[<c04dbc58>] (__driver_attach) from [<c04d9600>] (bus_for_each_dev+0x8c/0xd0)
[<c04d9600>] (bus_for_each_dev) from [<c04db1fc>] (driver_attach+0x2c/0x30)
[<c04db1fc>] (driver_attach) from [<c04daa98>] (bus_add_driver+0x50/0x260)
[<c04daa98>] (bus_add_driver) from [<c04dc440>] (driver_register+0x88/0x108)
[<c04dc440>] (driver_register) from [<c04dd6b4>] (__platform_driver_register+0x50/0x58)
[<c04dd6b4>] (__platform_driver_register) from [<c0b31248>] (macb_driver_init+0x24/0x28)
[<c0b31248>] (macb_driver_init) from [<c010203c>] (do_one_initcall+0x60/0x1a4)
[<c010203c>] (do_one_initcall) from [<c0b00f78>] (kernel_init_freeable+0x15c/0x1f8)
[<c0b00f78>] (kernel_init_freeable) from [<c0763d10>] (kernel_init+0x18/0x124)
[<c0763d10>] (kernel_init) from [<c0112d74>] (ret_from_fork+0x14/0x20)
Code: ba000002f5d1f03cf5d1f05cf5d1f07c (e8b151f8)
---[ end trace 3e4ec21905820a1f ]---
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.
Fixes: 4f86e81748fe ("drm/sun4i: Add support for H3 HDMI PHY variant") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While debugging driver crashes related to a buggy firmware
crashing under load, I noticed that ath10k_htt_rx_ring_free
could be called without being under lock. I'm not sure if this
is the root cause of the crash or not, but it seems prudent to
protect it.
Originally tested on 4.16+ kernel with ath10k-ct 10.4 firmware
running on 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Node /pcie@1e140000/pcie0 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie1 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie2 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie0 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge
Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
device_type was removed since according to documentation, it's deprecated
for pci(e) devices.
The ashmem driver did not check that the size/offset of the vma passed
to its .mmap() function was not larger than the ashmem object being
mapped. This could cause mmap() to succeed, even though accessing parts
of the mapping would later fail with a segmentation fault.
Ensure an error is returned by the ashmem_mmap() function if the vma
size is larger than the ashmem object size. This enables safer handling
of the problem in userspace.
The struct clk_init_data init variable is declared in the isp_xclk_init()
function so is an automatic variable allocated in the stack. But it's not
explicitly zero-initialized, so some init fields are left uninitialized.
This causes the data structure to have undefined values that may confuse
the common clock framework when the clock is registered.
For example, the uninitialized .flags field could have the CLK_IS_CRITICAL
bit set, causing the framework to wrongly prepare the clk on registration.
This leads to the isp_xclk_prepare() callback being called, which in turn
calls to the omap3isp_get() function that increments the isp dev refcount.
Since this omap3isp_get() call is unexpected, this leads to an unbalanced
omap3isp_get() call that prevents the requested IRQ to be later enabled,
due the refcount not being 0 when the correct omap3isp_get() call happens.
Fixes: 9b28ee3c9122 ("[media] omap3isp: Use the common clock framework") Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd36 ("media: ov772x: correct setting
of banding filter")
When the subdevice doesn't provide s_power core ops callback, the
v4l2_subdev_call for s_power returns -ENOIOCTLCMD. If the subdevice
doesn't have the special handling for its power saving mode, the s_power
isn't required. So -ENOIOCTLCMD from the v4l2_subdev_call should be
ignored.
Cc: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trace points to a corrupt skb inside kfree_skb(), seemingly because
one of the shared skb queues is getting corrupted. Most of the skb queues
ath10k uses are local to a single call stack, but three are shared among
multiple codepaths:
- rx_msdus_q,
- rx_in_ord_compl_q, and
- tx_fetch_ind_q
Of the three, the first two are manipulated using the unlocked skb_queue
functions without any additional lock protecting them. Use the locked
variants of skb_queue_* functions to protect these manipulations.
Signed-off-by: Bob Copeland <bobcopeland@fb.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running mirror_gre_bridge_1d_vlan tests on veth, several issues
cause spurious failures:
- vlan_ethtype should be ip, not ipv6 even in mirror-to-ip6gretap case,
because the overlay packet is still IPv4.
- Similarly ip_proto matches the innermost IP protocol, so can't be used
to filter out GRE packet. Drop the corresponding condition.
- Because the above fixes the filters to match in slow path as well,
they need to be made skip_hw so as not to double-count packets.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both calls to of_find_node_by_name() and of_get_next_child() return a
node pointer with refcount incremented thus it must be explicidly
decremented here after the last usage. As we are assured to have a
refcounted np either from the initial
of_find_node_by_name(NULL, name); or from the of_get_next_child(gpio, np)
in the while loop if we reached the error code path below, an
x of_node_put(np) is needed.
The posix timer overrun handling is broken because the forwarding functions
can return a huge number of overruns which does not fit in an int. As a
consequence timer_getoverrun(2) and siginfo::si_overrun can turn into
random number generators.
The k_clock::timer_forward() callbacks return a 64 bit value now. Make
k_itimer::ti_overrun[_last] 64bit as well, so the kernel internal
accounting is correct. 3Remove the temporary (int) casts.
Add a helper function which clamps the overrun value returned to user space
via timer_getoverrun(2) or siginfo::si_overrun limited to a positive value
between 0 and INT_MAX. INT_MAX is an indicator for user space that the
overrun value has been clamped.
Reported-by: Team OWL337 <icytxw@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Link: https://lkml.kernel.org/r/20180626132705.018623573@linutronix.de Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The posix timer ti_overrun handling is broken because the forwarding
functions can return a huge number of overruns which does not fit in an
int. As a consequence timer_getoverrun(2) and siginfo::si_overrun can turn
into random number generators.
As a first step to address that let the timer_forward() callbacks return
the full 64 bit value.
Cast it to (int) temporarily until k_itimer::ti_overrun is converted to
64bit and the conversion to user space visible values is sanitized.
Reported-by: Team OWL337 <icytxw@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Link: https://lkml.kernel.org/r/20180626132704.922098090@linutronix.de Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the address field in iio_chan_spec is filled with an accel
data register address for the corresponding axis.
In preparation for adding calibration offset support, this sets the
address field to the index of accel data registers instead of the actual
register address.
This change makes it easier to access both accel registers and
calibration offset registers with fewer lines of code as these are
located in X-axis, Y-axis, Z-axis order.
Cc: Eva Rachel Retuya <eraretuya@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a sama5d31 with a Full-HD dual LVDS panel (132MHz pixel clock) NAND
flash accesses have a tendency to cause display disturbances. Add a
module param to disable DMA from the NAND controller, since that fixes
the display problem for me.
Signed-off-by: Peter Rosin <peda@axentia.se> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/s390/mm/extmem.c: In function '__segment_load':
arch/s390/mm/extmem.c:436:2: warning: 'strncat' specified bound 7 equals
source length [-Wstringop-overflow=]
strncat(seg->res_name, " (DCSS)", 7);
What gcc complains about here is the misuse of strncat function, which
in this case does not limit a number of bytes taken from "src", so it is
in the end the same as strcat(seg->res_name, " (DCSS)");
Keeping in mind that a res_name is 15 bytes, strncat in this case
would overflow the buffer and write 0 into alignment byte between the
fields in the struct. To avoid that increasing res_name size to 16,
and reusing strlcat.
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Sebastian Ott <sebott@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The numa_node field of the tag_set struct has to be explicitly
initialized, otherwise it stays as 0, which is a valid numa node id and
cause memory allocation failure if node 0 is offline.
Acked-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UBSAN: Undefined behaviour in kernel/time/alarmtimer.c:811:7
signed integer overflow: 1529859276030040771 + 9223372036854775807 cannot be represented in type 'long long int'
Call Trace:
alarm_timer_nsleep+0x44c/0x510 kernel/time/alarmtimer.c:811
__do_sys_clock_nanosleep kernel/time/posix-timers.c:1235 [inline]
__se_sys_clock_nanosleep kernel/time/posix-timers.c:1213 [inline]
__x64_sys_clock_nanosleep+0x326/0x4e0 kernel/time/posix-timers.c:1213
do_syscall_64+0xb8/0x3a0 arch/x86/entry/common.c:290
alarm_timer_nsleep() uses ktime_add() to add the current time and the
relative expiry value. ktime_add() has no sanity checks so the addition
can overflow when the relative timeout is large enough.
Use ktime_add_safe() which has the necessary sanity checks in place and
limits the result to the valid range.
Fixes: 9a7adcf5c6de ("timers: Posix interface for alarm-timers") Reported-by: Team OWL337 <icytxw@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1807020926360.1595@nanos.tec.linutronix.de Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC arch/s390/kernel/sysinfo.o
arch/s390/kernel/sysinfo.c:275:12: warning: 'sysinfo_show' defined but not used [-Wunused-function]
static int sysinfo_show(struct seq_file *m, void *v)
Because acpi_lid_initialize_state() is called on every system
resume and it triggers acpi_lid_notify_state() which invokes
acpi_pm_wakeup_event() for the lid device, the lid's wakeup count is
incremented even if the lid was not the source of the event that woke up
the system. That behavior confuses user space deamons using
wakeup_count to identify the potential system wakeup source. To avoid
the confusion, only trigger acpi_pm_wakeup_event() in the
acpi_button_notify() path and don't do that in the
acpi_lid_initialize_state() path.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ret' will not be initialized if acpi_evaluate_integer() returns through
an error path, so it should not be used in this case. This fixes the
following Smatch static analyser error:
drivers/platform/x86/asus-wireless.c:76 asus_wireless_method() error:
uninitialized symbol 'ret'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use PHB in mode1 which uses bit 59 to select a correct DMA window.
However there is mode2 which uses bits 59:55 and allows up to 32 DMA
windows per a PE.
Even though documentation does not clearly specify that, it seems that
the actual hardware does not support bits 59:55 even in mode1, in other
words we can create a window as big as 1<<58 but DMA simply won't work.
This reduces the upper limit from 59 to 55 bits to let the userspace know
about the hardware limits.
Fixes: 7aafac11e3 "powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested" Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All packets in a bundle should use the same endpoint id as the
first lookahead.
This matches how things are done is ath6kl, however,
this patch can theoretically handle several bundles
in ath10k_sdio_mbox_rx_process_packets().
Without this patch we get lots of errors about invalid endpoint id:
ath10k_sdio mmc2:0001:1: invalid endpoint in look-ahead: 224
ath10k_sdio mmc2:0001:1: failed to get pending recv messages: -12
ath10k_sdio mmc2:0001:1: failed to process pending SDIO interrupts: -12
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. usb_get_descriptor can return a
negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
The approach for adding a device to the devices_idr data structure and for
removing it is as follows:
* &dev->dev_group.cg_item is initialized before a device is added to
devices_idr.
* If the reference count of a device drops to zero then
target_free_device() removes the device from devices_idr.
* All devices_idr manipulations are protected by device_mutex.
This means that increasing the reference count of a device is sufficient to
prevent removal from devices_idr and also that it is safe access
dev_group.cg_item for any device that is referenced by devices_idr. Use
this to modify target_find_device() and target_for_each_device() such that
these functions no longer introduce a dependency between device_mutex and
the configfs root inode mutex.
Note: it is safe to pass a NULL pointer to config_item_put() and also to
config_item_get_unless_zero().
This patch prevents that lockdep reports the following complaint:
======================================================
WARNING: possible circular locking dependency detected
4.12.0-rc1-dbg+ #1 Not tainted
------------------------------------------------------
rmdir/12053 is trying to acquire lock:
(device_mutex#2){+.+.+.}, at: [<ffffffffa010afce>]
target_free_device+0xae/0xf0 [target_core_mod]
but task is already holding lock:
(&sb->s_type->i_mutex_key#14){++++++}, at: [<ffffffff811c5c30>]
vfs_rmdir+0x50/0x140
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Currently an open firmware property is copied into partition_name variable
without keeping a room for \0.
Later one, this variable (partition_name), which is 97 bytes long, is
strncpyed into ibmvcsci_host_data->madapter_info->partition_name, which is
96 bytes long, possibly truncating it 'again' and removing the \0.
This patch simply decreases the partition name to 96 and just copy using
strlcpy() which guarantees that the string is \0 terminated. I think there
is no issue if this there is a truncation in this very first copy, i.e,
when the open firmware property is read and copied into the driver for the
very first time;
This issue also causes the following warning on GCC 8:
drivers/scsi/ibmvscsi/ibmvscsi.c:281:2: warning: strncpy output may be truncated copying 96 bytes from a string of length 96 [-Wstringop-truncation]
...
inlined from ibmvscsi_probe at drivers/scsi/ibmvscsi/ibmvscsi.c:2221:7:
drivers/scsi/ibmvscsi/ibmvscsi.c:265:3: warning: strncpy specified bound 97 equals destination size [-Wstringop-truncation]
CC: Bart Van Assche <bart.vanassche@wdc.com> CC: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Breno Leitao <leitao@debian.org> Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the scsi_transport_srp implementation it cannot be avoided to
iterate over a klist from atomic context when using the legacy block
layer instead of blk-mq. Hence this patch that makes it safe to use
klists in atomic context. This patch avoids that lockdep reports the
following:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
Possible interrupt unsafe locking scenario:
Without this fix, the thermal probe on i.MX6 might trigger a division
by zero exception later in the probe if the calibration does fail.
Note: This linux behavior (Division by zero in kernel) has been triggered
on a Qemu i.MX6 emulation where parameters in nvmem were not set. With this
fix the division by zero is not triggeed anymore as the thermal probe does
fail early.
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: Mike Christie <mchristi@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
... there are two more instances which want to be adjusted.
As said there, omitting suffixes from instructions in AT&T mode is bad
practice when operand size cannot be determined by the assembler from
register operands, and is likely going to be warned about by upstream
gas in the future (mine does already).
Add the other missing suffixes here as well.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/5B3A02DD02000078001CFB78@prv1-mh.provo.novell.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the RTC lock and unlock functions were introduced it was likely
assumed that they would always be called from irq enabled context, hence
the use of local_irq_disable/enable. This is no longer true as the
RTC+DDR path makes a late call during the suspend path after irqs
have been disabled to enable the RTC hwmod which calls both unlock and
lock, leading to IRQs being reenabled through the local_irq_enable call
in omap_hwmod_rtc_lock call.
To avoid this change the local_irq_disable/enable to
local_irq_save/restore to ensure that from whatever context this is
called the proper IRQ configuration is maintained.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a missing header otherwise compiler warns about missed prototype:
CC arch/x86/kernel/tsc_msr.o
arch/x86/kernel/tsc_msr.c:73:15: warning: no previous prototype for ‘cpu_khz_from_msr’ [-Wmissing-prototypes]
unsigned long cpu_khz_from_msr(void)
^~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Pavel Tatashin <pasha.tatashin@oracle.com> Link: https://lkml.kernel.org/r/20180629193113.84425-4-andriy.shevchenko@linux.intel.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
0:00:00.716640334 349 0x164f720 WARN v4l2bufferpool gstv4l2bufferpool.c:1195:gst_v4l2_buffer_pool_dqbuf:<v4l2src0:pool:src> Driver should never set v4l2_buffer.field to ANY
- fixes v4l2-compliance test failure:
Streaming ioctls:
test read/write: OK (Not Supported)
Video Capture:
Buffer: 0 Sequence: 0 Field: Any Timestamp: 58.383658s
fail: v4l2-test-buffers.cpp(297): g_field() == V4L2_FIELD_ANY
Signed-off-by: Peter Seiderer <ps.report@gmx.net> Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under heavy load vhost busypoll may run without suppressing
notification. For example tx zerocopy callback can push tx work while
handle_tx() is running, then busyloop exits due to vhost_has_work()
condition and enables notification but immediately reenters handle_tx()
because the pushed work was tx. In this case handle_tx() tries to
disable notification again, but when using event_idx it by design
cannot. Then busyloop will run without suppressing notification.
Another example is the case where handle_tx() tries to enable
notification but avail idx is advanced so disables it again. This case
also leads to the same situation with event_idx.
The problem is that once we enter this situation busyloop does not work
under heavy load for considerable amount of time, because notification
is likely to happen during busyloop and handle_tx() immediately enables
notification after notification happens. Specifically busyloop detects
notification by vhost_has_work() and then handle_tx() calls
vhost_enable_notify(). Because the detected work was the tx work, it
enters handle_tx(), and enters busyloop without suppression again.
This is likely to be repeated, so with event_idx we are almost not able
to suppress notification in this case.
To fix this, poll the work instead of enabling notification when
busypoll is interrupted by something. IMHO vhost_has_work() is kind of
interruption rather than a signal to completely cancel the busypoll, so
let's run busypoll after the necessary work is done.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory reservation for crashkernel could fail if there are holes around
kdump kernel offset (128M). Fail gracefully in such cases and print an
error message.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com> Tested-by: David Gibson <dgibson@redhat.com> Reviewed-by: Dave Young <dyoung@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rdma_ah_find_type() can reach into ib_device->port_immutable with a
potentially out-of-bounds port number, so check that the port number is
valid first.
Fixes: 44c58487d51a ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types") Signed-off-by: Tarick Bedeir <tarick@google.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"nents" is an unsigned int, so if ib_map_mr_sg() returns a negative
error code then it's type promoted to a high unsigned int which is
treated as success.
The srq->swq[] is allocated in bnxt_qplib_create_srq(). It has
srq->hwq.max_elements elements so these tests should be > instead of >=
or we might go beyond the end of the array.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sgid_tbl->tbl[] array is allocated in bnxt_qplib_alloc_sgid_tbl().
It has sgid_tbl->max elements. So the > should be >= to prevent
accessing one element beyond the end of the array.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When one node leaves cluster or stops the resyncing
(resync or recovery) array, then other nodes need to
call recover_bitmaps to continue the unfinished task.
But we need to clear suspend_area later after other
nodes copy the resync information to their bitmap
(by call bitmap_copy_from_slot). Otherwise, all nodes
could write to the suspend_area even the suspend_area
is not handled by any node, because area_resyncing
returns 0 at the beginning of raid1_write_request.
Which means one node could write suspend_area while
another node is resyncing the same area, then data
could be inconsistent.
So let's clear suspend_area later to avoid above issue
with the protection of bm lock. Also it is straightforward
to clear suspend_area after nodes have copied the resync
info to bitmap.
DML does not calculate chroma values for RQ when surface is not YUV, but DC
will unconditionally use the uninitialized values for HW programming.
This does not cause visual corruption since HW will ignore garbage chroma
values when surface is not YUV, but causes presubmission tests to fail
golden value comparison.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com> Signed-off-by: Eryk Brol <eryk.brol@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add suffix ULL to constant 5 and cast variables target_pix_clk_khz and
feedback_divider to uint64_t in order to avoid multiple potential integer
overflows and give the compiler complete information about the proper
arithmetic to use.
Notice that such constant and variables are used in contexts that
expect expressions of type uint64_t (64 bits, unsigned). The current
casts to uint64_t effectively apply to each expression as a whole,
but they do not prevent them from being evaluated using 32-bit
arithmetic instead of 64-bit arithmetic.
Also, once the expressions are properly evaluated using 64-bit
arithmentic, there is no need for the parentheses that enclose
them.
Addresses-Coverity-ID: 1460245 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1460286 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1460401 ("Unintentional integer overflow") Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device gets removed right after having registered a power_supply node,
we might enter in a deadlock between the remove call (that has a lock on
the parent device) and the deferred register work.
Allow the deferred register work to exit without taking the lock when
we are in the remove state.
Since proc_dointvec does not perform value range control,
proc_dointvec_minmax should be used to limit value range, which is
clearly intended here, as the internal representation of the value:
After decompression of 6lowpan socket data, an IPv6 header is inserted
before the existing socket payload. After this, we reset the
network_header value of the skb to account for the difference in payload
size from prior to decompression + the addition of the IPv6 header.
However, we fail to reset the mac_header value.
Leaving the mac_header value untouched here, can cause a calculation
error in net/packet/af_packet.c packet_rcv() function when an
AF_PACKET socket is opened in SOCK_RAW mode for use on a 6lowpan
interface.
On line 2088, the data pointer is moved backward by the value returned
from skb_mac_header(). If skb->data is adjusted so that it is before
the skb->head pointer (which can happen when an old value of mac_header
is left in place) the kernel generates a panic in net/core/skbuff.c
line 1717.
This panic can be generated by BLE 6lowpan interfaces (such as bt0) and
802.15.4 interfaces (such as lowpan0) as they both use the same 6lowpan
sources for compression and decompression.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com> Acked-by: Alexander Aring <aring@mojatatu.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the mapping has already been removed in the page table, it maybe
still exist in TLB. Suppose the freed IOVAs is reused by others before the
flush operation completed, the new user can not correctly access to its
meomory.
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b686 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Fixes: 46c99ac66222 ("power/reset: vexpress: Register with kernel restart handler") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the check on error return from the call to rtsx_write_register
is checking the error status from the previous call. Fix this by adding
in the missing assignment of retval.
Detected by CoverityScan, CID#709877
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hclgevf_free_vector function expects the caller to pass
the vector_id to it, and hclgevf_put_vector pass vector to
it now, which will cause vector allocation problem.
This patch fixes it by converting vector into vector_id before
calling hclgevf_free_vector.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The napi_alloc_skb is excepted to be called under the
non-preemptible code path when it is called by hns3_clean_rx_ring
during loopback selftest, otherwise the below warning will be
logged:
This patch fix it by disabling preemption when calling
hns3_clean_rx_ring during loopback selftest.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / users / dwmw2 / linux.git / log