Marek Behún [Sat, 20 Feb 2021 23:11:44 +0000 (00:11 +0100)]
ARM: dts: turris-omnia: configure LED[2]/INTn pin as interrupt pin
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org> Reported-by: Rui Salvaterra <rsalvaterra@gmail.com> Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia") Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: <stable@vger.kernel.org> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Revert "arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts"
The driver part of this support was not merged which leads to break
AHCI on all Marvell Armada 7k8k / CN913x platforms as it was reported
by Marcin Wojtas.
So for now let's remove it in order to fix the issue waiting for the
driver part really be merged.
This reverts commit 53e950d597e3578da84238b86424bfcc9e101d87. Fixes: 53e950d597e3 ("arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts") Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Merge tag 'at91-defconfig-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/defconfig
AT91 defconfig for 5.13:
- aligment with recent kernel for sama5_defconfig
- move of 2 options to built-in
- addition of useful modules for validation and CI
- addition of Hantro G1 VPU from staging
* tag 'at91-defconfig-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: configs: at91: Modernize UBI defconfig part
ARM: configs: at91: Add USB Video webcam class
ARM: configs: at91: Add mtd tests as modules
ARM: configs: at91: sama5: Add audio MIKROE PROTO board
ARM: configs: at91: sama5: Enable LAN78XX as module
ARM: configs: at91: sama5: PIOBU as built-in
ARM: configs: at91: sama5: MCP16502 regulator as built-in
ARM: configs: at91: sama5: enable the Hantro G1 engine
ARM: configs: at91: sama5: update with savedefconfig
Merge tag 'v5.12-next-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/defconfig
Enable option to boot MediaTek based chromebook (mt8173 and mt8183) with defconfig
* tag 'v5.12-next-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: defconfig: Enable options to support panel display for Mediatek Chromebooks
arm64: defconfig: Allow mt8173-based boards to boot from usb
Mark Brown [Thu, 1 Apr 2021 10:28:58 +0000 (11:28 +0100)]
ARM: configs: Remove REGULATOR_USERSPACE_CONSUMER
The userspace consumer is a development tool, not intended for producton
systems and so should not be present in defconfigs especially not those
for specific machines so is not a good fit for defconfig, remove it from
those defconfigs where it is enabled. No system in mainline actually
instantiates one.
Merge tag 'imx-defconfig-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/defconfig
i.MX defconfig change for 5.13:
It includes a number of arm64 defconfig update for i.MX8 devices
support. The following ones might deserve some notes.
- Although Hantro decoder driver are sitting in staging, people already
find it's quite useful on i.MX8M devices.
- i.MX PCIe driver has no option for module build.
- REALTEK_PHY becomes a built-in driver, because it's used on quite some
i.MX8 reference boards where people want to boot via NFS.
* tag 'imx-defconfig-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: configs: enable FlexTimer alarm timer
arm64: configs: Select REALTEK_PHY as built-in
arm64: configs: Enable PCIe support for imx8mq boards
arm64: defconfig: Enable the Hantro decoder
arm64: defconfig: add imx8qm pinctrl support
arm64: defconfig: Enable wm8960 audio driver.
arm64: defconfig: Enable asoc simple mux
arm64: defconfig: Enable devfreq support for i.MX8MQ
Merge tag 'arm64_defconfig_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/defconfig
ARM64 defconfig for v5.13
- Add support for Intel N5X SoCFPGA
- Add support for Intel Keem SoC
- Add support for Designware SPI driver
* tag 'arm64_defconfig_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: defconfig: enable Intel's eASIC N5X SoCFPGA and Keem Bay SoC
Linus Walleij [Mon, 1 Mar 2021 23:20:50 +0000 (00:20 +0100)]
ARM: configs: ux500: Update for new drivers
Some new driver support for the Ux500 devices landed in
v5.12-rc1 so update the defconfig to use them:
- TM2 touchkey, used on the Golden and Janice.
- SPI GPIO, used for the Janice display control.
- NTC thermistor, used for the HREF temperature
sensors.
- V4L2 flash control that gives support for LED
torch to userspaces such as Phosh.
- The LEDs Flash class and RT8515 Flash/torch LED
driver used in all the Samsung mobiles.
- FSA9480 extcon, used by Janice.
- BMC150 accelerometer, used by Janice.
- IIO rescaler, used for thermistors and ALS
on Janice.
- MPU3050 gyroscope driver used by Janice.
- Yamaha YAS530 magnetometer driver used by Janice.
Merge tag 'imx-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/soc
i.MX SoC update for 5.13:
- A couple of typo fixes on help text and comment.
* tag 'imx-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: Kconfig: Fix typo in help
ARM: mach-imx: Fix a spelling in the file pm-imx5.c
Merge tag 'omap-for-v5.13/genpd-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
Drop legacy data for dra7 and omap4/5 for genpd support for v5.13
Similar to what we have already done for am3 and 4, we can now boot dra7,
omap4, and omap5 with devicetree data and genpd without legacy SoC specific
built-in data.
Let's drop the legacy data for these SoCs, and the related "ti,hwmods"
custom devicetree property. As with these changes we now expect to have
complete devicetree data, let's also warn in the case if an old devicetree
data is noticed. And with the warning provided, there should not be any
need to delay dropping the legacy data as it just unnecessarily complicates
things.
The main reasons for dropping the legacy data is to avoid the burden of
maintaining a mixed boot process where both legacy built-in data and
devicetree data are needed. And we can now use standard reset driver,
genpd, and simple-pm-bus features.
These patches are based on the related devicetree changes to add the
missing interconnect target module configuration for these SoCs.
* tag 'omap-for-v5.13/genpd-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (87 commits)
bus: ti-sysc: Warn about old dtb for dra7 and omap4/5
ARM: OMAP2+: Stop building legacy code for dra7 and omap4/5
ARM: OMAP2+: Drop legacy platform data for omap5 hwmod
ARM: OMAP2+: Drop legacy platform data for omap5 l3
ARM: OMAP2+: Drop legacy platform data for omap5 l4_cfg
ARM: OMAP2+: Drop legacy platform data for omap5 l4_per
ARM: OMAP2+: Drop legacy platform data for omap5 l4_wkup
ARM: OMAP2+: Drop legacy platform data for omap5 sata
ARM: OMAP2+: Drop legacy platform data for omap5 mpu
ARM: OMAP2+: Drop legacy platform data for omap5 emif
ARM: OMAP2+: Drop legacy platform data for omap5 dmm
ARM: dts: Configure simple-pm-bus for omap5 l3
ARM: dts: Configure simple-pm-bus for omap5 l4_cfg
ARM: dts: Configure simple-pm-bus for omap5 l4_per
ARM: dts: Configure simple-pm-bus for omap5 l4_wkup
ARM: dts: Move omap5 l3-noc to a separate node
ARM: dts: Move omap5 mmio-sram out of l3 interconnect
ARM: dts: Configure interconnect target module for omap5 sata
ARM: dts: Configure interconnect target module for omap5 gpmc
ARM: dts: Configure interconnect target module for omap5 mpu
...
Merge tag 'socfpga_update_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/drivers
SoCFPGA updates for v5.13
- Patches from Krzysztof Kozlowski the cleans up and consolidate support for
SoCFPGA platforms
- Rename ARCH_SOCFPGA into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_STRATIX10 into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_AGILEX into ARCH_INTEL_SOCFPGA
- Consolidate ARCH_N5X into ARCH_INTEL_SOCFPGA
* tag 'socfpga_update_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: drop ARCH_SOCFPGA
reset: socfpga: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
i2c: altera: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
fpga: altera: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
dmaengine: socfpga: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs
clk: socfpga: use ARCH_INTEL_SOCFPGA also for 32-bit ARM SoCs (and compile test)
clk: socfpga: allow compile testing of Stratix 10 / Agilex clocks
arm64: socfpga: merge Agilex and N5X into ARCH_INTEL_SOCFPGA
EDAC: altera: merge ARCH_SOCFPGA and ARCH_STRATIX10
clk: socfpga: merge ARCH_SOCFPGA and ARCH_STRATIX10
clk: socfpga: build together Stratix 10, Agilex and N5X clock drivers
net: stmmac: merge ARCH_SOCFPGA and ARCH_STRATIX10
mfd: altera: merge ARCH_SOCFPGA and ARCH_STRATIX10
ARM: socfpga: introduce common ARCH_INTEL_SOCFPGA
clk: socfpga: allow building N5X clocks with ARCH_N5X
Merge tag 'v5.12-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
- add MT8183 support to mutex driver
MMSYS:
- use per SoC array to describe the possible routing
- add support for MT8183
Power management domains:
- fix the case of a domain fails to get added
- add names for each power domain to make debugging easier
PMIC wrapper:
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
* tag 'v5.12-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
soc: mediatek: pm-domains: Add a power domain names for mt8167
soc: mediatek: pm-domains: Add a power domain names for mt8192
soc: mediatek: pm-domains: Add a power domain names for mt8183
soc: mediatek: pm-domains: Add a meaningful power domain name
soc: mediatek: Make symbol 'mtk_mutex_driver' static
soc: mediatek: mmsys: Add mt8183 mmsys routing table
soc: mediatek: pwrap: add pwrap driver for MT6873/8192 SoCs
dt-bindings: mediatek: add compatible for MT6873/8192 pwrap
soc: mediatek: pwrap: add arbiter capability
soc: mediatek: pwrap: use BIT() macro
soc: mediatek: pm-domains: Fix missing error code in scpsys_add_subdomain()
soc: mediatek: mmsys: Use an array for setting the routing registers
soc: mediatek: mmsys: Create struct mtk_mmsys to store context data
soc: mediatek: add mtk mutex support for MT8183
* arm/dt: (239 commits)
ARM: mstar: Add mpll to base dtsi
ARM: mstar: Add the external clocks to the base dsti
ARM: mstar: Select MSTAR_MSC313_MPLL
ARM: dts: stm32: Add PTP clock to Ethernet controller
arm64: dts: mediatek: fix reset GPIO level on pumpkin
arm64: dts: mt8183: add mt8183 pumpkin board
dt-bindings: arm64: dts: mediatek: Add mt8183-pumpkin board
ARM: dts: stm32: Enable crc1 and cryp1 where applicable on DHSOM
ARM: dts: stm32: Update GPIO line names on PicoITX
ARM: dts: stm32: Update GPIO line names on DRC02
ARM: dts: stm32: Fill GPIO line names on AV96
ARM: dts: stm32: Fill GPIO line names on DHCOM SoM
dt-bindings: serial: stm32: Use 'type: object' instead of false for 'additionalProperties'
ARM: stm32: Add a new SoC - STM32H750
ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6
ARM: dts: stm32: fix i2c node typo in stm32h743
ARM: dts: stm32: add new instances for stm32h743 MCU
ARM: dts: stm32: introduce stm32h7-pinctrl.dtsi to support stm32h750
dt-bindings: arm: stm32: Add compatible strings for ART-PI board
Documentation: arm: stm32: Add stm32h750 value line doc
...
Merge tag 'v5.12-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
- add trivial bindings for MT8195
- fix dtbs_check warnings
- add pinmux for build-in Wifi on MT7622 evaluation borad
MT8183:
- fix USB wakeup register
- add regulator for EVB board
- add registers to mailbox consumers
- add thermal zone and trip points for CPU cooling
- Add new boards:
* ASUS Chromebook Flip CM3
* ASUS Chromebook Detachable CM3
* Acer Chromebook Spin 311
* Lenovo 10e Chromebook Tablet
MT8173:
- fix PHY property in DSI
- fix power-domain for PMIC wrapper
Pumkin:
- add MT8516 based board
- add MT8183 based board
- fix reset pin for MT8167 and MT8516 based boards
Merge tag 'tegra-for-5.13-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree fixes for v5.12-rc6
This contains a couple of device tree fixes for the v5.12 release cycle.
These are needed for proper audio support on Jetson AGX Xavier, to boot
the Jetson Xavier NX from an SD card and to be able to suspend/resume
the Jetson TX2.
* tag 'tegra-for-5.13-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Move clocks from RT5658 endpoint to device node
arm64: tegra: Fix mmc0 alias for Jetson Xavier NX
arm64: tegra: Set fw_devlink=on for Jetson TX2
arm64: tegra: Add unit-address for ACONNECT on Tegra186
Merge tag 'tegra-for-5.13-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.13-rc1
This contains a couple of improvements and fixes for various 32-bit
Tegra-based boards.
* tag 'tegra-for-5.13-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: acer-a500: Add atmel,wakeup-method property
ARM: tegra: Specify tps65911 as wakeup source
ARM: tegra: Specify memory suspend OPP in device-tree
ARM: tegra: Specify CPU suspend OPP in device-tree
ARM: tegra: ouya: Specify all CPU cores as cooling devices
ARM: tegra: nexus7: Specify all CPU cores as cooling devices
ARM: tegra: acer-a500: Rename avdd to vdda of touchscreen node
ARM: tegra: acer-a500: Specify all CPU cores as cooling devices
ARM: tegra: acer-a500: Reduce thermal throttling hysteresis to 0.2C
ARM: tegra: acer-a500: Enable core voltage scaling
ARM: tegra: paz00: Enable full voltage scaling ranges for CPU and Core domains
ARM: tegra: cardhu: Support CPU thermal throttling
ARM: tegra: cardhu: Support CPU frequency and voltage scaling on all board variants
ARM: tegra: ventana: Support CPU thermal throttling
ARM: tegra: ventana: Support CPU and Core voltage scaling
Merge tag 'tegra-for-5.13-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.13-rc1
One single changes that adds the nvidia,pmc property to the XUSB pad
controller binding, which will subsequently be used to implement USB
sleepwalk functionality.
* tag 'tegra-for-5.13-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: phy: tegra-xusb: Add nvidia,pmc prop
Merge tag 'stm32-dt-for-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.13, round 1
Highlights:
----------
MCU part:
-Add stm32h750 SoC support. It is based on stm32h743 and embeds
crypto IPs and 2 ADC.
-Add new art-pi board based on stm32h750. This board embeds:
-8MB QSPI flash.
-16MB SPI flash.
-32MB SDRAM.
-AP6212 combo (wifi/bt/fm).
MPU part:
-Use dedicated PTP clock for Ethernet controller on stm32mp151.
-Enable i2c analog filter on stm32mp151.
-DH:
-Update GPIO names.
-Enable crc1 & crryp1 on DHSOM.
-Engicam: add new boards support:
-MicroGEA SOM which embeds STM32MP157aac, 512 MB Nand Flash
I2S.
-MicroGEA STM32MP1 Microdev 2.0 which embeds MicroGEA SOM,
Ethernet up to 100 Mbps, USB typeA, microSD, UMTS LTE, Wifi/BT
LVDS panel connector.
-MicroGEA STM32MP1 MicroDev 2.0 7" which embeds a MicroGEA STM32MP1
MicroDev 2.0 plus 7" Open Frame panel solution (7" AUO B101AW03 LVDS panel
and EDT DT5526 Touch)
-i.Core STM32MP1 EDIMM SoM based on STM32MP157A.
-C.TOUCH 2.0 n EDIMM compliant general purpose Carrier board with capacitive
touch interface support based on i.Core STM32MP1 EDIMM SoM.
It embeds ETH 10/100, wifi/bt, CAN, USB TypeA/OTG, LVDS pannel connector.
-EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive Evaluation
Board based on i.Core STM32MP1 EDIMM SoM. IT embeds LCD 7" C.Touch,
wifi/bt,2*LVDS FHD, 3*USB2, 1*USB3 ...
* tag 'stm32-dt-for-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (26 commits)
ARM: dts: stm32: Add PTP clock to Ethernet controller
ARM: dts: stm32: Enable crc1 and cryp1 where applicable on DHSOM
ARM: dts: stm32: Update GPIO line names on PicoITX
ARM: dts: stm32: Update GPIO line names on DRC02
ARM: dts: stm32: Fill GPIO line names on AV96
ARM: dts: stm32: Fill GPIO line names on DHCOM SoM
dt-bindings: serial: stm32: Use 'type: object' instead of false for 'additionalProperties'
ARM: stm32: Add a new SoC - STM32H750
ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6
ARM: dts: stm32: fix i2c node typo in stm32h743
ARM: dts: stm32: add new instances for stm32h743 MCU
ARM: dts: stm32: introduce stm32h7-pinctrl.dtsi to support stm32h750
dt-bindings: arm: stm32: Add compatible strings for ART-PI board
Documentation: arm: stm32: Add stm32h750 value line doc
ARM: dts: stm32: enable the analog filter for all I2C nodes in stm32mp151
ARM: dts: stm32: Add Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit
dt-bindings: arm: stm32: Add Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit
ARM: dts: stm32: Add Engicam i.Core STM32MP1 C.TOUCH 2.0
ARM: dts: stm32: Add Engicam i.Core STM32MP1 SoM
dt-bindings: arm: stm32: Add Engicam i.Core STM32MP1 C.TOUCH 2.0
...
Merge tag 'ux500-dts-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS changes for the v5.13 kernel cycle:
- Fix up the WLAN on Janice
- Fix the touchscreen on TVK R2
- Push down definitions to the UIBs instead of
trying to share too much.
- Bump the AUX1 voltage on the AB8500 so the
touchscreen will work.
- Define the CTTYSP touchscreen on the TVK R3.
* tag 'ux500-dts-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add Cypress CTTYSP touch to TVK UIB
ARM: dts: ux500: Bump AUX1 voltage
ARM: dts: ux500: Clarify UIB version per board
ARM: dts: ux500: Totally separate TVK R2 and R3
ARM: dts: ux500: Push TC35893 defines to each UIB
ARM: dts: ux500: Fix up TVK R3 sensors
ARM: dts: ux500: Push sensors to TVK R2 board
ARM: dts: ux500: Move Synaptics to right include
ARM: dts: ux500: Fix touchscreen on TVK R2
ARM: dts: ux500: Fix BT+WLAN on Janice
Merge tag 'imx-dt64-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.13:
- A series from Dong Aisheng to update i.MX8Q device trees for adopting
SS (SubSystems) based bindings.
- New board support: Kontron pitx-imx8m, Engicam i.Core MX8M Mini.
- A series from Adrien Grassein to add various peripheral support for
imx8mm-nitrogen-r2 board.
- A series from Guido Günther to update librem5-devkit device tree.
- A number of patches from Michael Walle to add Root Complex Event
Collector interrupt, update MTD partitions and add rtc0 alias for
ls1028a-kontron-sl28 board.
- Add EQOS MAC support for phyBOARD-Pollux-i.MX8MP.
- Add 2x2 SFP+ cage support for clearfog-itx boards.
- Small and random update for various boards.
* tag 'imx-dt64-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (55 commits)
arm64: dts: fsl-ls1028a-kontron-sl28: add rtc0 alias
arm64: dts: ls1028a: move rtc alias to individual boards
arm64: dts: fsl-ls1028a-kontron-sl28: combine unused partitions
arm64: dts: fsl-ls1028a-kontron-sl28: move MTD partitions
arm64: dts: imx8mp-evk: Improve the Ethernet PHY description
arm64: dts: imx8mq-librem5-r3: Mark buck3 as always on
arm64: dts: imx8mq-librem5: Hog the correct gpio
arm64: dts: lx2160a-clearfog-itx: add SFP support
arm64: dts: imx8mp-phyboard-pollux-rdk: Change debug UART
arm64: dts: imx8mn: Reorder flexspi clock-names entry
arm64: dts: imx8mm: Reorder flexspi clock-names entry
arm64: dts: ls1028a: set up the real link speed for ENETC port 2
arm64: dts: imx8mm-nitrogen-r2: add ecspi2 support
arm64: dts: imx: add imx8qm mek support
arm64: dts: imx: add imx8qm common dts file
arm64: dts: imx8qm: add dma ss support
arm64: dts: imx8: split adma ss into dma and audio ss
arm64: dts: imx8qm: add conn ss support
arm64: dts: imx8qm: add lsio ss support
arm64: dts: imx8: switch to new lpcg clock binding
...
Merge tag 'imx-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree change for 5.13:
- New board support: i.MX7D based reMarkable2.
- Clean up imx6ql-pfla02 hog group by moving pins into corresponded
client groups.
- Add Netronix embedded controller for imx50-kobo-aura.
- A series from Sebastian Reichel to improve GE Bx50v3 device trees.
- Support I2C bus recovery for imx6qdl-wandboard by adding SCL/SDA
GPIOs.
- Remove unnecessary #address-cells/#size-cells from imx6qdl-gw boards.
- Various small and random device tree update.
* tag 'imx-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (21 commits)
ARM: dts: imx6: pbab01: Set USB OTG port to peripheral
ARM: dts: imx6: pfla02: Fix USB vbus enable pinmuxing
ARM: imx7d-remarkable2: Initial device tree for reMarkable2
ARM: dts: imx7d-mba7: Remove unsupported PCI properties
ARM: dts: imx6qdl-gw*: Remove unnecessary #address-cells/#size-cells
ARM: dts: imx6dl-plybas: Fix gpio-keys W=1 warnings
ARM: dts: imx: bx50v3: Define GPIO line names
ARM: dts: imx: bx50v3: i2c GPIOs are open drain
ARM: dts: imx6q-ba16: improve PHY information
ARM: dts: imx6q-ba16: add USB OTG VBUS enable GPIO
ARM: dts: ls1021a: mark crypto engine dma coherent
ARM: dts: colibri-imx6ull: Change drive strength for usdhc2
ARM: dts: imx6ql-pfla02: Move "hog" pins into corresponded pin groups
ARM: dts: imx6qdl-phytec-pbab01: Select synchronous mode for AUDMUX
ARM: dts: imx6qdl-ts7970: Drop redundant "fsl,mode" option
ARM: dts: imx53-qsb: Describe the esdhc1 card detect pin
ARM: dts: ls1021a: Harmonize DWC USB3 DT nodes name
ARM: dts: imx6qdl-wandboard: add scl/sda gpios definitions for i2c bus recovery
ARM: dts: imx: Mark IIM as syscon on i.MX51/i.MX53
ARM: dts: imx6sl-tolino-shine2hd: Add Netronix embedded controller
...
Merge tag 'imx-bindgins-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX bindings update for 5.13:
- Add vendor prefix for reMarkable.
- Add compatible for reMarkable 2 e-Ink tablet, Kontron pITX-imx8m
board, Engicam i.Core MX8M Mini devices.
- Add compatbile 'fsl,imx8qm-mu' for i.MX mailbox bindings.
- One correction on example clock-names in imx8qxp-lpcg bindings.
* tag 'imx-bindgins-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add the reMarkable 2 e-Ink tablet
dt-bindings: Add vendor prefix for reMarkable
dt-bindings: mailbox: mu: add imx8qm support
dt-bindings: arm: fsl: add imx8qm boards compatible string
dt-bindings: arm: fsl: add Kontron pITX-imx8m board
dt-bindings: arm: fsl: Add Engicam i.Core MX8M Mini EDIMM2.2 Starter Kit
dt-bindings: arm: fsl: Add Engicam i.Core MX8M Mini C.TOUCH 2.0
dt-bindings: clock: imx8qxp-lpcg: correct the example clock-names
Merge tag 'arm-soc/for-5.13/devicetre-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.13, please pull the following:
- Rafal continues to add support for the 4908 SoCs and describes the USB
PHY, firmware flash partitions and Ethernet switch and Ethernet
controller. He also adds support for the TP-Link Archer C2300 V1
router and upates the Netgear R8000P and Asus GT-AC5300 routers network
ports description.
Merge tag 'arm-soc/for-5.13/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.13, please pull the following:
- Rafal fixes YAML warnings for the memory nodes of BCM5301X nodes and
adds support for the NVMEM NVRAM node on Linksys and Luxul WLAN
routers. He also fixes up the partitions for the Linksys EA9400 to
use the newly introduced parser compatible and sets the power LED to
its default state.
* tag 'arm-soc/for-5.13/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Set Linksys EA9500 power LED
ARM: dts: BCM5301X: Fix Linksys EA9500 partitions
ARM: dts: BCM5301X: Describe NVMEM NVRAM on Linksys & Luxul routers
ARM: dts: BCM5301X: fix "reg" formatting in /memory node
Merge tag 'socfpga_dts_update_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.13
- Patches from Krzysztof Kozlowski that fixes dtc warnings
and dtbs_check warnings
- Adjust the "cnds,read-delay" value for the Agilex devkit to 2
* tag 'socfpga_dts_update_for_v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: intel: adjust qpsi read-delay property
arm64: dts: intel: socfpga_agilex_socdk_nand: align LED node names with dtschema
arm64: dts: intel: socfpga_agilex: align node names with dtschema
arm64: dts: intel: socfpga_agilex: use defined for GIC interrupts
arm64: dts: intel: socfpga_agilex: move usbphy out of soc node
arm64: dts: intel: socfpga_agilex: remove default status=okay
arm64: dts: intel: socfpga_agilex: move timer out of soc node
arm64: dts: intel: socfpga_agilex: move clocks out of soc node
arm64: dts: intel: socfpga: override clocks by label
Merge tag 'omap-for-v5.13/dts-genpd-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for genpd support for v5.13
In order to move omap4/5 and dra7 to probe with devicetree data and genpd,
we need to add the missing interconnect target module configuration for
the drivers that do not still have it. This is similar to what we have
already done earlier for am3 and 4 earlier.
These patches are very much similar for all the three SoCs here. The dra7
changes were already available for v5.12 merge window, but were considered
too late to add for v5.12. The patches for omap4 and 5 follow the same
pattern, except for PCIe that is available only on dra7.
We do the changes one driver at a time, and still keep the legacy property
for "ti,hwmods" mostly around, except for cases when already not needed.
We will be dropping the custom property and related legacy data in a
follow-up series.
* tag 'omap-for-v5.13/dts-genpd-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (53 commits)
ARM: dts: Configure simple-pm-bus for omap5 l3
ARM: dts: Configure simple-pm-bus for omap5 l4_cfg
ARM: dts: Configure simple-pm-bus for omap5 l4_per
ARM: dts: Configure simple-pm-bus for omap5 l4_wkup
ARM: dts: Move omap5 l3-noc to a separate node
ARM: dts: Move omap5 mmio-sram out of l3 interconnect
ARM: dts: Configure interconnect target module for omap5 sata
ARM: dts: Configure interconnect target module for omap5 gpmc
ARM: dts: Configure interconnect target module for omap5 mpu
ARM: dts: Configure interconnect target module for omap5 emif
ARM: dts: Configure interconnect target module for omap5 dmm
ARM: dts: Prepare for simple-pm-bus for omap4 l3
ARM: dts: Configure simple-pm-bus for omap4 l4_cfg
ARM: dts: Configure simple-pm-bus for omap4 l4_per
ARM: dts: Configure simple-pm-bus for omap4 l4_wkup
ARM: dts: Move omap4 l3-noc to a separate node
ARM: dts: Move omap4 mmio-sram out of l3 interconnect
ARM: dts: Configure interconnect target module for omap4 mpu
ARM: dts: Configure interconnect target module for omap4 debugss
ARM: dts: Configure interconnect target module for omap4 emif
...
* arm/drivers: (37 commits)
tee: optee: do not check memref size on return from Secure World
tee: optee: fix build error caused by recent optee tracepoints feature
firmware: imx: scu-pd: add missed ADC1 pd
firmware: imx: scu-pd: Update comments for single global power domain
soc/tegra: pmc: Print out domain name when reset fails to acquire
soc/tegra: pmc: Ensure that clock rates aren't too high
soc/tegra: pmc: Fix completion of power-gate toggling
soc/tegra: pmc: Fix imbalanced clock disabling in error code path
soc/tegra: regulators: Fix locking up when voltage-spread is out of range
soc/tegra: pmc: Provide USB sleepwalk register map
soc: bcm: bcm-pmb: add BCM63138 SATA support
dt-bindings: power: bcm-pmb: add BCM63138 binding
clk: tegra: Don't enable PLLE HW sequencer at init
clk: tegra: Add PLLE HW power sequencer control
bus: ti-sysc: Use kzalloc for allocating only one thing
bus: ti-sysc: remove unneeded semicolon
ARM: OMAP2+: Make symbol 'pdata_quirks_init_clocks' static
pwm: Add Raspberry Pi Firmware based PWM bus
dt-bindings: pwm: Add binding for RPi firmware PWM bus
input: raspberrypi-ts: Release firmware handle when not needed
...
* arm/fixes: (348 commits)
ARM: mvebu: avoid clang -Wtautological-constant warning
ARM: pxa: mainstone: avoid -Woverride-init warning
ARM: omap1: fix building with clang IAS
soc/fsl: qbman: fix conflicting alignment attributes
ARM: keystone: fix integer overflow warning
ARM: dts: imx6: pbab01: Set vmmc supply for both SD interfaces
arm64: dts: imx8mm/q: Fix pad control of SD1_DATA0
Linux 5.12-rc5
io_uring: remove unsued assignment to pointer io
io_uring: don't cancel extra on files match
io_uring: don't cancel-track common timeouts
io_uring: do post-completion chore on t-out cancel
io_uring: fix timeout cancel return code
Revert "signal: don't allow STOP on PF_IO_WORKER threads"
Revert "kernel: freezer should treat PF_IO_WORKER like PF_KTHREAD for freezing"
Revert "kernel: treat PF_IO_WORKER like PF_KTHREAD for ptrace/signals"
Revert "signal: don't allow sending any signals to PF_IO_WORKER threads"
kernel: stop masking signals in create_io_thread()
io_uring: handle signals for IO threads like a normal thread
block: don't create too many partitions
...
Merge tag 'tegra-for-5.13-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.13-rc1
Contains a couple of fixes to the PMC power domain implementation and
exports a regmap from PMC needed to implement USB sleepwalk support.
* tag 'tegra-for-5.13-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Print out domain name when reset fails to acquire
soc/tegra: pmc: Ensure that clock rates aren't too high
soc/tegra: pmc: Fix completion of power-gate toggling
soc/tegra: pmc: Fix imbalanced clock disabling in error code path
soc/tegra: regulators: Fix locking up when voltage-spread is out of range
soc/tegra: pmc: Provide USB sleepwalk register map
Merge tag 'tegra-for-5.13-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
clk: tegra: Changes for v5.13-rc1
This adds PLLE HW sequencer support which is necessary for USB sleepwalk
functionality.
* tag 'tegra-for-5.13-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Don't enable PLLE HW sequencer at init
clk: tegra: Add PLLE HW power sequencer control
Merge tag 'imx-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers change for 5.13:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
* tag 'imx-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: scu-pd: add missed ADC1 pd
firmware: imx: scu-pd: Update comments for single global power domain
firmware: imx: scu-pd: do not power off console domain
soc: imx: add i.MX51/i.MX53 unique id support
Merge tag 'arm-soc/for-5.13/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom ARM/ARM64/MIPS based SoCs drivers
changes for 5.13, please pull the following:
- Rafal updates the Broadcom PMB binding to support BCM63138 and updates
the code to support resetting the 63138 SATA controller
* tag 'arm-soc/for-5.13/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: bcm-pmb: add BCM63138 SATA support
dt-bindings: power: bcm-pmb: add BCM63138 binding
Merge tag 'optee-memref-size-for-v5.13' of git://git.linaro.org/people/jens.wiklander/linux-tee into arm/drivers
OP-TEE skip check of returned memref size
* tag 'optee-memref-size-for-v5.13' of git://git.linaro.org/people/jens.wiklander/linux-tee:
tee: optee: do not check memref size on return from Secure World
Merge tag 'omap-for-v5.13/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/drivers
Driver changes for omaps for genpd support for v5.13
In order to move omap4/5 and dra7 to probe with devicetree data and genpd,
we need to patch the related drivers to prepare.
These are mostly ti-sysc interconnect target module driver changes and soc
init changes. However, there are minor changes to other drivers too. There
are changes for pci-dra7xx probe, omap-prm idle configuration, and a omap5
clock change:
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
There are also few minor non-urgent fixes:
- soc init code pdata_quirks_init_clocks should be static
- ti-sysc has few unneeded semiconon typos
- ti-sysc can use kzalloc instead of kcalloc for a single element
* tag 'omap-for-v5.13/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Use kzalloc for allocating only one thing
bus: ti-sysc: remove unneeded semicolon
ARM: OMAP2+: Make symbol 'pdata_quirks_init_clocks' static
PCI: pci-dra7xx: Prepare for deferred probe with module_platform_driver
clk: ti: omap5: Add missing gpmc and ocmc clkctrl
soc: ti: omap-prm: Allow hardware supported retention when idle
ARM: OMAP2+: Init both prm and prcm nodes early for clocks
bus: ti-sysc: Check for old incomplete dtb
bus: ti-sysc: Detect more modules for debugging
bus: ti-sysc: Probe for l4_wkup and l4_cfg interconnect devices first
bus: ti-sysc: Fix initializing module_pa for modules without sysc register
ARM: dts: Fix moving mmc devices with aliases for omap4 & 5
ARM: dts: Drop duplicate sha2md5_fck to fix clk_disable race
soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva
bus: ti-sysc: Fix warning on unbind if reset is not deasserted
ARM: OMAP2+: Fix smartreflex init regression after dropping legacy data
soc: ti: omap-prm: Fix reboot issue with invalid pcie reset map for dra7
ARM: dts: am33xx: add aliases for mmc interfaces
bus: omap_l3_noc: mark l3 irqs as IRQF_NO_THREAD
Merge tag 'rpi-poe-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nsaenz/linux-rpi into arm/drivers
Raspberry Pi driver updates for v5.13:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
* tag 'rpi-poe-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nsaenz/linux-rpi:
pwm: Add Raspberry Pi Firmware based PWM bus
dt-bindings: pwm: Add binding for RPi firmware PWM bus
input: raspberrypi-ts: Release firmware handle when not needed
staging: vchiq: Release firmware handle on unbind
soc: bcm: raspberrypi-power: Release firmware handle on unbind
reset: raspberrypi: Release firmware handle on unbind
gpio: raspberrypi-exp: Release firmware handle on unbind
clk: bcm: rpi: Release firmware handle on unbind
firmware: raspberrypi: Introduce devm_rpi_firmware_get()
firmware: raspberrypi: Keep count of all consumers
Clang warns about the comparison when using a 32-bit phys_addr_t:
drivers/bus/mvebu-mbus.c:621:17: error: result of comparison of constant 4294967296 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (reg_start >= 0x100000000ULL)
Arnd Bergmann [Mon, 8 Mar 2021 15:34:21 +0000 (16:34 +0100)]
ARM: omap1: fix building with clang IAS
The clang integrated assembler fails to build one file with
a complex asm instruction:
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: error: invalid instruction, any one of the following would fix this:
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: armv6t2
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: thumb2
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
The problem is that 'NR_IRQS_LEGACY' is not defined here. Apparently
gas does not care because we first add and then subtract this number,
leading to the immediate value to be the same regardless of the
specific definition of NR_IRQS_LEGACY.
Neither the way that 'gas' just silently builds this file, nor the
way that clang IAS makes nonsensical suggestions for how to fix it
is great. Fortunately there is an easy fix, which is to #include
the header that contains the definition.
When building with W=1, gcc points out that the __packed attribute
on struct qm_eqcr_entry conflicts with the 8-byte alignment
attribute on struct qm_fd inside it:
drivers/soc/fsl/qbman/qman.c:189:1: error: alignment 1 of 'struct qm_eqcr_entry' is less than 8 [-Werror=packed-not-aligned]
I assume that the alignment attribute is the correct one, and
that qm_eqcr_entry cannot actually be unaligned in memory,
so add the same alignment on the outer struct.
Arnd Bergmann [Tue, 23 Mar 2021 13:18:05 +0000 (14:18 +0100)]
ARM: keystone: fix integer overflow warning
clang warns about an impossible condition when building with 32-bit
phys_addr_t:
arch/arm/mach-keystone/keystone.c:79:16: error: result of comparison of constant 51539607551 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
mem_end > KEYSTONE_HIGH_PHYS_END) {
~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-keystone/keystone.c:78:16: error: result of comparison of constant 34359738368 with expression of type 'phys_addr_t' (aka 'unsigned int') is always true [-Werror,-Wtautological-constant-out-of-range-compare]
if (mem_start < KEYSTONE_HIGH_PHYS_START ||
~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~
Change the temporary variable to a fixed-size u64 to avoid the warning.
Daniel Palmer [Mon, 1 Mar 2021 12:35:41 +0000 (21:35 +0900)]
ARM: mstar: Add the external clocks to the base dsti
All of the currently known MStar/SigmaStar ARMv7 SoCs have an "xtal"
clock input that is usually 24MHz and an "RTC xtal" that is usually 32KHz.
The xtal input has to be connected to something so it's enabled by default.
The MSC313 and MSC313E do not bring the RTC clock input out to the pins
so it's impossible to connect it. The SSC8336 does bring the input
out to the pins but it's not always actually connected to something.
The RTC node needs to always be present because in the future the nodes
for the clock muxes will refer to it even if it's not usable.
The RTC node is disabled by default and should be enabled at the board
level if the RTC input is wired up.
Kurt Kanzenbach [Tue, 16 Mar 2021 08:06:44 +0000 (09:06 +0100)]
ARM: dts: stm32: Add PTP clock to Ethernet controller
Add the PTP clock to the Ethernet controller. Otherwise, the driver uses the
main clock to derive the PTP frequency which is not necessarily the correct one.
Tested with linuxptp on Olimex STMP1-OLinuXino-LIME2.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enric Balletbo i Serra [Thu, 25 Feb 2021 17:49:57 +0000 (18:49 +0100)]
soc: mediatek: pm-domains: Add a meaningful power domain name
Add the power domains names to the power domain struct so we
have meaningful name for every power domain. This also removes the
following debugfs error message.
Merge tag 'imx-fixes-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.12, round 2:
- Fix a system failure on imx6qdl-phytec-pfla02 board when booting from
SD, by adding missing vmmc supply for SD interfaces.
- Fix address typo in i.MX8MM/Q IOMUXC_SD1_DATA0_GPIO2_IO2 definition.
* tag 'imx-fixes-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: pbab01: Set vmmc supply for both SD interfaces
arm64: dts: imx8mm/q: Fix pad control of SD1_DATA0
Merge tag 'omap-for-v5.12/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
More fixes for omaps for v5.12-rc cycle
Two fixes for hangs, mmc slot order fix, and a voltage typo fix:
- Remove unused duplicate sha2md5_fck clock node that can race with the
OMAP4_SHA2MD5_CLKCTRL clock node for disable for unused clocks
- Add aliases for omap4/5 mmc to put the slots back into the right
order again
- Fix typo for bionic voltage controllers that accidentally use mpu
for all instances instead of mpu, core and iva
- Fix random hangs for droid4 caused by missing fix from TI Android
kernel tree to do a dummy smc call on cpuidle wakeup path
* tag 'omap-for-v5.12/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: PM: update ROM return address for OSWR and OFF
ARM: OMAP4: Fix PMIC voltage domains for bionic
ARM: dts: Fix moving mmc devices with aliases for omap4 & 5
ARM: dts: Drop duplicate sha2md5_fck to fix clk_disable race
Merge tag 'arm-soc/for-5.12/devicetree-part2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoC changes for 5.12,
please pull the following:
- Florian reverts the adding of the second level interrupt controller
for HDMI BSC interrupts since they collide with the main I2C
controller (i2c-bcm2835).
* tag 'arm-soc/for-5.12/devicetree-part2' of https://github.com/Broadcom/stblinux:
Revert "ARM: dts: bcm2711: Add the BSC interrupt controller"
Fabien Parent [Wed, 17 Feb 2021 20:59:44 +0000 (21:59 +0100)]
arm64: dts: mt8183: add mt8183 pumpkin board
The MT8183 Pumpkin board is manufactured by OLogic and includes
a MediaTek MT8183 SoC with 2GB of RAM.
The board provides the following IOs:
* 2 USB Type-A ports
* Ethernet
* Serial UART over micro-USB port
* 1 USB Type-C dual role port
* 1 USB Type-C power only port
* 1 Jack for audio
* RPI compatible header
* MT7668 wiresless chip with Wi-Fi AC and BT 5
* Micro-HDMI port
* 2 connectors for CSI cameras
* 1 connector for DSI display
* 1 JTAG port
Marek Vasut [Mon, 29 Mar 2021 19:36:14 +0000 (21:36 +0200)]
ARM: dts: stm32: Update GPIO line names on PicoITX
Use more specific custom GPIO line names which denote exactly where
the GPIO came from, i.e. the base board. Also, update the new blank
GPIO line names set up by stm32mp15xx-dhcom-som.dtsi back to their
original values.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Mon, 29 Mar 2021 19:36:13 +0000 (21:36 +0200)]
ARM: dts: stm32: Update GPIO line names on DRC02
Use more specific custom GPIO line names which denote exactly where
the GPIO came from, i.e. the base board. Also, update the new blank
GPIO line names set up by stm32mp15xx-dhcom-som.dtsi back to their
original values.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Mon, 29 Mar 2021 19:36:11 +0000 (21:36 +0200)]
ARM: dts: stm32: Fill GPIO line names on DHCOM SoM
Fill in the custom GPIO line names used by DH on the DHCOM SoM.
The GPIO line names are in accordance to DHCOM Design Guide R04
available at [1], section 3.9 GPIO.
dillon min [Wed, 31 Mar 2021 08:28:45 +0000 (16:28 +0800)]
dt-bindings: serial: stm32: Use 'type: object' instead of false for 'additionalProperties'
To use additional properties 'bluetooth' on serial, need replace false with
'type: object' for 'additionalProperties' to make it as a node, else will
run into dtbs_check warnings.
'arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: serial@40004800:
'bluetooth' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: af1c2d81695b ("dt-bindings: serial: Convert STM32 UART to json-schema") Reported-by: kernel test robot <lkp@intel.com> Tested-by: Valentin Caron <valentin.caron@foss.st.com> Signed-off-by: dillon min <dillon.minfei@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/1616757302-7889-8-git-send-email-dillon.minfei@gmail.com Signed-off-by: dillon min <dillon.minfei@gmail.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
dillon min [Wed, 31 Mar 2021 08:28:43 +0000 (16:28 +0800)]
ARM: dts: stm32: add support for art-pi board based on stm32h750xbh6
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750-art-pi.dts to support art-pi board
dillon min [Wed, 31 Mar 2021 08:28:42 +0000 (16:28 +0800)]
ARM: dts: stm32: introduce stm32h7-pinctrl.dtsi to support stm32h750
This patch is intend to add support stm32h750 value line,
just add stm32h7-pinctrl.dtsi for extending, with following changes:
- rename stm32h743-pinctrl.dtsi to stm32h7-pinctrl.dtsi
- move 'pin-controller' from stm32h7-pinctrl.dtsi to stm32h743.dtsi, to
fix make dtbs_check warrnings
arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: soc: 'i2c@40005C00',
'i2c@58001C00' do not match any of the regexes:
'@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$', 'pinctrl-[0-9]+'
Signed-off-by: dillon min <dillon.minfei@gmail.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Enric Balletbo i Serra [Wed, 31 Mar 2021 09:06:58 +0000 (11:06 +0200)]
arm64: defconfig: Enable options to support panel display for Mediatek Chromebooks
There are some Mediatek based Chromebooks supported in the kernel. Enable the
required config options to have the panel display working on both devices.
This was tested on the ACER Chromebook R13 (MT8173) and the Lenovo
Ideapad Duet (MT8183), but should also enable display support for similar
devices.
Krzysztof Kozlowski [Mon, 8 Mar 2021 17:09:43 +0000 (18:09 +0100)]
arm64: dts: intel: socfpga_agilex: align node names with dtschema
Align the NAND, GIC and UART node names with dtschema to silence
dtbs_check warnings like:
arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dt.yaml:
intc@fffc1000: $nodename:0: 'intc@fffc1000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dt.yaml:
serial0@ffc02000: $nodename:0: 'serial0@ffc02000' does not match '^serial(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Krzysztof Kozlowski [Mon, 8 Mar 2021 17:09:37 +0000 (18:09 +0100)]
arm64: dts: intel: socfpga: override clocks by label
Using full paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Hsin-Hsiung Wang [Fri, 12 Mar 2021 15:34:43 +0000 (23:34 +0800)]
soc: mediatek: pwrap: add arbiter capability
Add arbiter capability for pwrap driver.
The arbiter capability uses new design to judge the priority and latency
for multi-channel.
The design with arbiter support cannot change the watchdog timer.
This patch is preparing for adding mt6873/8192 pwrap support.
Boris Lysov [Sat, 13 Mar 2021 23:37:35 +0000 (02:37 +0300)]
arm: mediatek: dts: activate SMP for mt6589
This simple patch activates SMP for mt6589 by adding the missing
"enable-method" property. After applying this patch kernel log
indicates all cores are brought up:
[ 0.070122] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.071652] Setting up static identity map for 0x80100000 - 0x80100054
[ 0.072711] rcu: Hierarchical SRCU implementation.
[ 0.073853] smp: Bringing up secondary CPUs ...
[ 0.133675] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.193675] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.253675] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.253818] smp: Brought up 1 node, 4 CPUs
[ 0.256930] SMP: Total of 4 processors activated (7982.28 BogoMIPS).
[ 0.257855] CPU: All CPU(s) started in SVC mode.
Before this change CPU cores 1-3 didn't start and the following lines
were in kernel log:
[ 0.070126] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.071640] Setting up static identity map for 0x80100000 - 0x80100054
[ 0.072706] rcu: Hierarchical SRCU implementation.
[ 0.073850] smp: Bringing up secondary CPUs ...
[ 0.076052] smp: Brought up 1 node, 1 CPU
[ 0.076678] SMP: Total of 1 processors activated (2000.48 BogoMIPS).
[ 0.077603] CPU: All CPU(s) started in SVC mode.
projects / users / jedix / linux-maple.git / log