of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc192 ("mtd: physmap_of: add a hook for Versatile write protection") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220523143255.4376-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b0afd44bc192 ("mtd: physmap_of: add a hook for Versatile write protection") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220523140205.48625-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
In case push_rcu() and related functions are buggy, there's a
WARN_ON(len >= 128), which the selftest tries to hit by being tricky. In
case it is hit, we shouldn't corrupt the kernel's stack, though;
otherwise it may be hard to even receive the report that it's buggy. So
conditionalize the stack write based on that WARN_ON()'s return value.
Note that this never *actually* happens anyway. The WARN_ON() in the
first place is bounded by IS_ENABLED(DEBUG), and isn't expected to ever
actually hit. This is just a debugging sanity check.
Additionally, hoist the constant 128 into a named enum,
MAX_ALLOWEDIPS_BITS, so that it's clear why this value is chosen.
Using msleep() is problematic because it's compared against
ratelimiter.c's ktime_get_coarse_boottime_ns(), which means on systems
with slow jiffies (such as UML's forced HZ=100), the result is
inaccurate. So switch to using schedule_hrtimeout().
However, hrtimer gives us access only to the traditional posix timers,
and none of the _COARSE variants. So now, rather than being too
imprecise like jiffies, it's too precise.
One solution would be to give it a large "range" value, but this will
still fire early on a loaded system. A better solution is to align the
timeout to the actual coarse timer, and then round up to the nearest
tick, plus change.
So add the timeout to the current coarse time, and then
schedule_hrtimer() until the absolute computed time.
This should hopefully reduce flakes in CI as well. Note that we keep the
retry loop in case the entire function is running behind, because the
test could still be scheduled out, by either the kernel or by the
hypervisor's kernel, in which case restarting the test and hoping to not
be scheduled out still helps.
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the case of sk->dccps_qpolicy == DCCPQ_POLICY_PRIO, dccp_qpolicy_full
will drop a skb when qpolicy is full. And the lock in dccp_sendmsg is
released before sock_alloc_send_skb and then relocked after
sock_alloc_send_skb. The following conditions may lead dccp_qpolicy_push
to add skb to an already full sk_write_queue:
thread1--->lock
thread1--->dccp_qpolicy_full: queue is full. drop a skb
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_full: queue is not full. no need to drop.
thread2--->unlock
thread1--->lock
thread1--->dccp_qpolicy_push: add a skb. queue is full.
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_push: add a skb!
thread2--->unlock
Fix this by moving dccp_qpolicy_full.
Fixes: b1308dc015eb ("[DCCP]: Set TX Queue Length Bounds via Sysctl") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Link: https://lore.kernel.org/r/20220729110027.40569-1-hbh25y@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The prototype of input features of ionic_set_nic_features() is
netdev_features_t, but the vlan_flags is using the private
definition of ionic drivers. It should use the variable
ctx.cmd.lif_setattr.features, rather than features to check
the vlan flags. So fixes it.
Fixes: beead698b173 ("ionic: Add the basic NDO callbacks for netdev support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Acked-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bernard reported that trying to unload rose module would lead
to infamous messages:
unregistered_netdevice: waiting for rose0 to become free. Usage count = xx
This patch solves the issue, by making sure each socket referring to
a netdevice holds a reference count on it, and properly releases it
in rose_release().
rose_dev_first() is also fixed to take a device reference
before leaving the rcu_read_locked section.
Following patch will add ref_tracker annotations to ease
future bug hunting.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Bernard Pidoux <f6bvp@free.fr> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Bernard Pidoux <f6bvp@free.fr> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to suppress warnings from sily map sizes. Also switch
from GFP_USER to GFP_KERNEL_ACCOUNT, I'm pretty sure I misunderstood
the flags when writing this code.
Fix max_rate option in TC, check for proper quanta boundaries.
Check for minimum value provided and if it fits expected 50Mbps
quanta.
Without this patch, iavf could send settings for max_rate limiting
that would be accepted from by PF even the max_rate option is less
than expected 50Mbps quanta. It results in no rate limiting
on traffic as rate limiting will be floored to 0.
The commit 3c82a21f4320 ("net: allow binding socket in a VRF when
there's an unbound socket") changed the inet socket lookup to avoid
packets in a VRF from matching an unbound socket. This is to ensure the
necessary isolation between the default and other VRFs for routing and
forwarding. VRF-unaware processes running in the default VRF cannot
access another VRF and have to be run with 'ip vrf exec <vrf>'. This is
to be expected with tcp_l3mdev_accept disabled, but could be reallowed
when this sysctl option is enabled. So instead of directly checking dif
and sdif in inet[6]_match, here call inet_sk_bound_dev_eq(). This
allows a match on unbound socket for non-zero sdif i.e. for packets in
a VRF, if tcp_l3mdev_accept is enabled.
Fixes: 3c82a21f4320 ("net: allow binding socket in a VRF when there's an unbound socket") Signed-off-by: Mike Manning <mvrmanning@gmail.com> Link: https://lore.kernel.org/netdev/a54c149aed38fded2d3b5fdb1a6c89e36a083b74.camel@lasnet.de/ Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 6dd9a14e92e5 ("net: Allow accepted sockets to be bound to l3mdev domain") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The authentication algorithm supports a maximum of 128-byte keys.
The allocated key memory is insufficient.
Fixes: 2f072d75d1ab ("crypto: hisilicon - Add aead support on SEC2") Signed-off-by: Kai Ye <yekai13@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without MODULE_DEVICE_TABLE, crypto_safexcel.ko module is not automatically
loaded on platforms where inside-secure crypto HW is specified in device
tree (e.g. Armada 3720). So add missing MODULE_DEVICE_TABLE for of.
MLX5E_MAX_RQ_NUM_MTTS should be the maximum value, so that
MLX5_MTT_OCTW(MLX5E_MAX_RQ_NUM_MTTS) fits into u16. The current value of
1 << 17 results in MLX5_MTT_OCTW(1 << 17) = 1 << 16, which doesn't fit
into u16. This commit replaces it with the maximum value that still
fits u16.
The driver reports whether TX/RX TLS device offloads are supported, but
not which ciphers/versions, these should be handled by returning
-EOPNOTSUPP when .tls_dev_add() is called.
Remove the WARN_ON kernel trace when the driver gets a request to
offload a cipher/version that is not supported as it is expected.
Not all DPB entries will be used most of the time. Unused entries will
thus have invalid timestamps. They will produce negative buffer index
which is not specifically handled. This works just by chance in current
code. It will even produce bogus pointer, but since it's not used, it
won't do any harm.
Let's fix that brittle design by skipping writing DPB entry altogether
if timestamp is invalid.
After successfull station association, if station queues are disabled for
some reason, the related lists are not emptied. So if some new element is
added to the list in iwl_mvm_mac_wake_tx_queue, it can match with the old
one and produce a BUG like this:
Commit 7a4836560a61 changes simple_write_to_buffer() with memdup_user()
but it forgets to change the value to be returned that came from
simple_write_to_buffer() call. It results in the following warning:
warning: variable 'rc' is uninitialized when used here [-Wuninitialized]
return rc;
^~
Remove rc variable and just return the passed in length if the
memdup_user() succeeds.
Cc: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: kernel test robot <lkp@intel.com> Fixes: 7a4836560a6198d245d5732e26f94898b12eb760 ("wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()") Fixes: ff974e4083341383d3dd4079e52ed30f57f376f0 ("wil6210: debugfs interface to send raw WMI command") Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220724202452.61846-1-ammar.faizi@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver") Signed-off-by: Liang He <windhl@126.com> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
After commit 3a5c7e4611dd, the variable errc is accessed before being
initialized, c.f. below W=2 warning:
| In function 'pch_can_error',
| inlined from 'pch_can_poll' at drivers/net/can/pch_can.c:739:4:
| drivers/net/can/pch_can.c:501:29: warning: 'errc' may be used uninitialized [-Wmaybe-uninitialized]
| 501 | cf->data[6] = errc & PCH_TEC;
| | ^
| drivers/net/can/pch_can.c: In function 'pch_can_poll':
| drivers/net/can/pch_can.c:484:13: note: 'errc' was declared here
| 484 | u32 errc, lec;
| | ^~~~
Moving errc initialization up solves this issue.
Fixes: 3a5c7e4611dd ("can: pch_can: do not report txerr and rxerr during bus-off") Reported-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/all/20220721160032.9348-1-mailhol.vincent@wanadoo.fr Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, data[5..7] of struct can_frame, when used as a CAN error
frame, are defined as being "controller specific". Device specific
behaviours are problematic because it prevents someone from writing
code which is portable between devices.
As a matter of fact, data[5] is never used, data[6] is always used to
report TX error counter and data[7] is always used to report RX error
counter. can-utils also relies on this.
This patch updates the comment in the uapi header to specify that
data[5] is reserved (and thus should not be used) and that data[6..7]
are used for error counters.
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Link: https://lore.kernel.org/all/20220719143550.3681-8-mailhol.vincent@wanadoo.fr CC: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The assignment of the value to the variable total in the loop
condition must be enclosed in additional parentheses, since otherwise,
in accordance with the precedence of the operators, the conjunction
will be performed first, and only then the assignment.
Due to this error, a warning later in the function after the loop may
not occur in the situation when it should.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru> Fixes: 0d4171e2153b ("p54: implement flush callback") Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220714134831.106004-1-subkhankulov@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful call to p54spi_request_firmware(), it
must be undone by a corresponding release_firmware() as already done in
the error handling path of p54spi_request_firmware() and in the .remove()
function.
Add the missing call in the error handling path and remove it from
p54spi_request_firmware() now that it is the responsibility of the caller
to release the firmware
The simple_write_to_buffer() function will succeed if even a single
byte is initialized. However, we need to initialize the whole buffer
to prevent information leaks. Just use memdup_user().
Fixes: ff974e408334 ("wil6210: debugfs interface to send raw WMI command") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/Ysg14NdKAZF/hcNG@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
The original direct splicing mechanism from Jens required the input to
be a regular file because it was avoiding the special socket case. It
also recognized blkdevs as being close enough to a regular file. But it
forgot about chardevs, which behave the same way and work fine here.
This is an okayish heuristic, but it doesn't totally work. For example,
a few chardevs should be spliceable here. And a few regular files
shouldn't. This patch fixes this by instead checking whether FMODE_LSEEK
is set, which represents decently enough what we need rewinding for when
splicing to internal pipes.
Fixes: b92ce5589374 ("[PATCH] splice: add direct fd <-> fd splicing support") Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 7337224fc150 ("bpf: Improve the info.func_info and info.func_info_rec_size behavior")
accidently made bpf_prog_ksym_set_name() conservative for bpf subprograms.
Fixed it so instead of "bpf_prog_tag_F" the stack traces print "bpf_prog_tag_full_subprog_name".
Fixes: 7337224fc150 ("bpf: Improve the info.func_info and info.func_info_rec_size behavior") Reported-by: Tejun Heo <tj@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20220714211637.17150-1-alexei.starovoitov@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value from system() is a waitpid-style integer. Do not return
it directly because with the implicit masking in exit() it will always
return 0. Access it with appropriate macros to really pass on errors.
Fixes: 7290ce1423c3 ("selftests/timers: Add clocksource-switch test from timetest suite") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: John Stultz <jstultz@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
BPF map name is limited to BPF_OBJ_NAME_LEN.
A map name is defined as being longer than BPF_OBJ_NAME_LEN,
it will be truncated to BPF_OBJ_NAME_LEN when a userspace program
calls libbpf to create the map. A pinned map also generates a path
in the /sys. If the previous program wanted to reuse the map，
it can not get bpf_map by name, because the name of the map is only
partially the same as the name which get from pinned path.
The syscall information below show that map name "process_pinned_map"
is truncated to "process_pinned_".
bpf(BPF_OBJ_GET, {pathname="/sys/fs/bpf/process_pinned_map",
bpf_fd=0, file_flags=0}, 144) = -1 ENOENT (No such file or directory)
This patch check that if the name of pinned map are the same as the
actual name for the first (BPF_OBJ_NAME_LEN - 1),
bpf map still uses the name which is included in bpf object.
current code of __tcp_retransmit_skb only check TCP_SKB_CB(skb)->seq
in send window, and TCP_SKB_CB(skb)->seq_end maybe out of send window.
If receiver has shrunk his window, and skb is out of new window, it
should retransmit a smaller portion of the payload.
The mdp_ipi_comm structure defines a command that is either
PROCESS (start processing) or DEINIT (destroy instance); we
are using this one to send PROCESS or DEINIT commands from Linux
to an MDP instance through a VPU write but, while the first wants
us to stay 4-bytes aligned, the VPU instead requires an 8-bytes
data alignment.
Keeping in mind that these commands are executed immediately
after sending them (hence not chained with others before the
VPU/MDP "actually" start executing), it is fine to simply add
a padding of 4 bytes to this structure: this keeps the same
performance as before, as we're still stack-allocating it,
while avoiding hackery inside of mtk-vpu to ensure alignment
bringing a definitely bigger performance impact.
Fixes: c8eb2d7e8202 ("[media] media: Add Mediatek MDP Driver") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Houlong Wei <houlong.wei@mediatek.com> Reviewed-by: Irui Wang <irui.wang@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kunpeng920 encryption driver is used to deencrypt and decrypt
packets during the softirq, it is not allowed to use mutex lock. The
kernel will report the following error:
And the calltrace of task that actually caused kernel hungs as follows:
__switch_to+124
__schedule+548
schedule+72
schedule_timeout+348
__down_common+188
__down+24
down+104
hinic_get_stats64+44 [hinic]
dev_get_stats+92
bond_get_stats+172 [bonding]
dev_get_stats+92
dev_seq_printf_stats+60
dev_seq_show+24
seq_read_iter+964
seq_read+220
proc_reg_read+164
vfs_read+172
ksys_read+108
__arm64_sys_read+28
el0_svc_common+132
do_el0_svc+40
el0_svc+24
el0_sync_handler+164
el0_sync+324
When getting device stats from bond, kernel will call bond_get_stats().
It first holds the spinlock bond->stats_lock, and then call
hinic_get_stats64() to collect hinic device's stats.
However, hinic_get_stats64() calls `down(&nic_dev->mgmt_lock)` to
protect its critical section, which may schedule current task out.
And if system is under high pressure, the task cannot be woken up
immediately, which eventually triggers kernel hung panic.
Since previous patch has replaced hinic_dev.tx_stats/rx_stats with local
variable in hinic_get_stats64(), there is nothing need to be protected
by lock, so just removing down()/up() is ok.
Fixes: edd384f682cc ("net-next/hinic: Add ethtool and stats") Signed-off-by: Qiao Ma <mqaio@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function hinic_get_stats64() will do two operations:
1. reads stats from every hinic_rxq/txq and accumulates them
2. calls hinic_rxq/txq_clean_stats() to clean every rxq/txq's stats
For hinic_get_stats64(), it could get right data, because it sums all
data to nic_dev->rx_stats/tx_stats.
But it is wrong for get_drv_queue_stats(), this function will read
hinic_rxq's stats, which have been cleared to zero by hinic_get_stats64().
I have observed hinic's cleanup operation by using such command:
> watch -n 1 "cat ethtool -S eth4 | tail -40"
Result after a few seconds:
...
rxq7_pkts: 0
rxq7_bytes: 0
rxq7_errors: 0
rxq7_csum_errors: 0
rxq7_other_errors: 0
...
rxq9_pkts: 2
rxq9_bytes: 132
rxq9_errors: 0
rxq9_csum_errors: 0
rxq9_other_errors: 0
...
rxq11_pkts: 1
rxq11_bytes: 170
rxq11_errors: 0
rxq11_csum_errors: 0
rxq11_other_errors: 0
To solve this problem, we just keep every queue's total stats in their own
queue (aka hinic_{rxq|txq}), and simply sum all per-queue stats every time
calling hinic_get_stats64().
With that solution, there is no need to clean per-queue stats now,
and there is no need to maintain global hinic_dev.{tx|rx}_stats, too.
Fixes: edd384f682cc ("net-next/hinic: Add ethtool and stats") Signed-off-by: Qiao Ma <mqaio@linux.alibaba.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'vlan_bitmap' is a bitmap and is used as such. So allocate it with
devm_bitmap_zalloc() and its explicit bit size (i.e. VLAN_N_VID).
This avoids the need of the VLAN_BITMAP_SIZE macro which:
- needlessly has a 'nic_dev' parameter
- should be "long" (and not byte) aligned, so that the bitmap semantic
is respected
This is in fact not an issue because VLAN_N_VID is 4096 at the time
being, but devm_bitmap_zalloc() is less verbose and easier to understand.
The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f81 ("drm/bridge/sii8620: add support for burst eMSC transmissions") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible for users to try to duplicate the CRTC state even when the
state doesn't exist. drm_atomic_helper_crtc_duplicate_state() (and other
users of __drm_atomic_helper_crtc_duplicate_state()) already guard this
with a WARN_ON() instead of crashing, so let's do that here too.
Currently, xsk_socket__delete frees BPF resources regardless of ctx
refcount. Xdpxceiver has a test to verify whether underlying BPF
resources would not be wiped out after closing XSK socket that was
bound to interface with other active sockets. From library's xsk part
perspective it also means that the internal xsk context is shared and
its refcount is bumped accordingly.
After a switch to loading XDP prog based on previously opened XSK
socket, mentioned xdpxceiver test fails with:
not ok 16 [xdpxceiver.c:swap_xsk_resources:1334]: ERROR: 9/"Bad file descriptor
which means that in swap_xsk_resources(), xsk_socket__delete() released
xskmap which in turn caused a failure of xsk_socket__update_xskmap().
To fix this, when deleting socket, decrement ctx refcount before
releasing BPF resources and do so only when refcount dropped to 0 which
means there are no more active sockets for this ctx so BPF resources can
be freed safely.
Fixes: 2f6324a3937f ("libbpf: Support shared umems between queues and devices") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20220629143458.934337-5-maciej.fijalkowski@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
ld: arch/arm64/crypto/ghash-ce-glue.o: in function 'ghash_ce_mod_exit':
ghash-ce-glue.c:(.exit.text+0x24): undefined reference to 'crypto_unregister_aead'
ld: arch/arm64/crypto/ghash-ce-glue.o: in function 'ghash_ce_mod_init':
ghash-ce-glue.c:(.init.text+0x34): undefined reference to 'crypto_register_aead'
Fixes: 537c1445ab0b ("crypto: arm64/gcm - implement native driver using v8 Crypto Extensions") Signed-off-by: Qian Cai <quic_qiancai@quicinc.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Fixes: 682e62c45406 ("drm/vc4: Fix support for interlaced modes on HDMI.") Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com> Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike the previous generations, the HSM clock limitation is way above
what we can reach without scrambling, so let's move the maximum
frequency we support to the maximum clock frequency without scrambling.
drm_atomic_helper_connector_reset uses kmalloc which, from an API
standpoint, can fail, and thus setting connector->state to NULL.
However, our reset hook then calls drm_atomic_helper_connector_tv_reset
that will access connector->state without checking if it's a valid
pointer or not.
Make sure we don't end up accessing a NULL pointer.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-5-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
vc4_dsi_encoder_disable is partially an open coded version of
drm_bridge_chain_disable, but it missed a termination condition
in the loop for ->disable which meant that no post_disable
calls were made.
DSI0 seemingly had very little or no testing as a load of
the register mappings were incorrect/missing, so host
transfers always timed out due to enabling/checking incorrect
bits in the interrupt enable and status registers.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-16-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
vc4_dsi was registering both dsi0 and dsi1 as VC4_ENCODER_TYPE_DSI1
which seemed to work OK for a single DSI display, but fails
if there are two DSI displays connected.
Update to register the correct type.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-15-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most of the differences between DSI0 and DSI1 are handled through the
ID. However, the BCM2711 DSI is going to introduce one more variable to
the mix and will break some expectations of the earlier, simpler, test.
Let's add a variant structure that will address most of the differences
between those three controllers.
The DSI clocks setup function has been using an array to store the clock
name of either the DSI0 or DSI1 blocks, using the port ID to choose the
proper one.
Let's switch to an snprintf call to do the same thing and simplify the
array a bit.
For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.
Amend the setup accordingly.
Fixes: a86773d120d7 ("drm/vc4: Add support for feeding DSI encoders from the pixel valve.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-14-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 86c1b9eff3f2 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current plane margin calculation code clips the right and bottom
edges of the range based using the left and top margins.
This is obviously wrong, so let's fix it.
Fixes: 666e73587f90 ("drm/vc4: Take margin setup into account when updating planes") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-6-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Fixes: 21af94cf1a4c ("drm/vc4: Add support for scaling of display planes.") Signed-off-by: Dom Cobley <popcornmix@gmail.com> Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
video_device_alloc() allocates memory for vdev,
when video_register_device() fails, it doesn't release the memory and
leads to memory leak, call video_device_release() to fix this.
Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.
Fixes: 9aba42efe85b ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device") Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Every iteration of for_each_available_child_of_node() decrements
the reference counter of the previous node. There is no decrement
when break out from the loop and results in refcount leak.
Add missing of_node_put() to fix this.
As mipi_dsi_driver_register could return error if fails,
it should be better to check the return value and return error
if fails.
Moreover, if i2c_add_driver fails, mipi_dsi_driver_register
should be reverted.
On shutdown, each CCP device instance performs shutdown processing.
However, __sev_platform_shutdown_locked() uses the controlling psp
structure to obtain the pointer to the sev_device structure. However,
during driver initialization, it is possible that an error can be received
from the firmware that results in the sev_data pointer being cleared from
the controlling psp structure. The __sev_platform_shutdown_locked()
function does not check for this situation and will segfault.
While not common, this scenario should be accounted for. Add a check for a
NULL sev_device structure before attempting to use it.
Fixes: 5441a07a127f ("crypto: ccp - shutdown SEV firmware on kexec") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The prototype of .features is netdev_features_t, it should use
NETIF_F_LLTX and NETIF_F_HW_VLAN_STAG_TX, not NETIF_F_LLTX_BIT
and NETIF_F_HW_VLAN_STAG_TX_BIT.
radeon is MIT. This were incorrectly changed in
commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
and
commit d198b34f3855 (".gitignore: add SPDX License Identifier")
and:
commit ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Fixes: d198b34f3855 (".gitignore: add SPDX License Identifier") Fixes: ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig") Fixes: b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2053 Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab67077 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to not add fancy protection for drv_priv we can move
htc_handle->drv_priv initialization at the end of the
ath9k_htc_probe_device() and add helper macro to make
all *_STAT_* macros NULL safe, since syzbot has reported related NULL
deref in that macros [1]
We got the following warning when booting the kernel:
[ 3.243674] INFO: trying to register non-static key.
[ 3.243922] The code is fine but needs lockdep annotation, or maybe
[ 3.244230] you didn't initialize this object before use?
[ 3.245642] Call Trace:
[ 3.247836] lock_acquire+0xff/0x2d0
[ 3.248727] tw686x_audio_irq+0x1a5/0xcc0 [tw686x]
[ 3.249211] tw686x_irq+0x1f9/0x480 [tw686x]
The lock 'vc->qlock' will be initialized in tw686x_video_init(), but the
driver registers the irq before calling the tw686x_video_init(), and we
got the warning.
Fix this by registering the irq at the end of probe
Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sk->sk_forward_alloc is 150000, and we need to schedule 150001 bytes,
we want to allocate 1 byte more (rounded up to one page),
instead of 150001 :/
projects / users / dwmw2 / linux.git / log