In “ubifs_check_node”, when the value of "node_len" is abnormal,
the code will goto label of "out_len" for execution. Then, in the
following "ubifs_dump_node", if inode type is "UBIFS_DATA_NODE",
in "print_hex_dump", an out-of-bounds access may occur due to the
wrong "ch->len".
Therefore, when the value of "node_len" is abnormal, data length
should to be adjusted to a reasonable safe range. At this time,
structured data is not credible, so dump the corrupted data directly
for analysis.
Signed-off-by: Liu Song <liu.song11@zte.com.cn> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some EFI systems, the video BIOS is provided by the EFI firmware. The
boot stub code stores the physical address of the ROM image in pdev->rom.
Currently we attempt to access this pointer using phys_to_virt(), which
doesn't work with CONFIG_HIGHMEM.
On these systems, attempting to load the radeon module on a x86_32 kernel
can result in the following:
Fix the issue by updating all drivers which can access a platform provided
ROM. Instead of calling the helper function pci_platform_rom() which uses
phys_to_virt(), call ioremap() directly on the pdev->rom.
radeon_read_platform_bios() previously directly accessed an __iomem
pointer. Avoid this by calling memcpy_fromio() instead of kmemdup().
pci_platform_rom() now has no remaining callers, so remove it.
Link: https://lore.kernel.org/r/20200319021623.5426-1-mikel@mikelr.com Signed-off-by: Mikel Rychliski <mikel@mikelr.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Introduce a call to xprt_rdma_free_addresses() similar to the way
that the TCP backchannel releases a transport's peer address
strings.
Fixes: 5d252f90a800 ("svcrdma: Add class for RDMA backwards direction transport") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'maxlen' is the total size of the destination buffer. There is only one
caller and this value is 256.
When we compute the size already used and what we would like to add in
the buffer, the trailling NULL character is not taken into account.
However, this trailling character will be added by the 'strcat' once we
have checked that we have enough place.
So, there is a off-by-one issue and 1 byte of the stack could be
erroneously overwridden.
Take into account the trailling NULL, when checking if there is enough
place in the destination buffer.
While at it, also replace a 'sprintf' by a safer 'snprintf', check for
output truncation and avoid a superfluous 'strlen'.
Fixes: dc9a16e49dbba ("svc: Add /proc/sys/sunrpc/transport files") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ cel: very minor fix to documenting comment Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Correct race condition where ioaccel is re-enabled before the raid_map is
updated. For RAID_1, RAID_1ADM, and RAID 5/6 there is a BUG_ON called which
is bad.
- Change event thread to disable ioaccel only. Send all requests down the
RAID path instead.
- Have rescan thread handle offload_enable.
- Since there is only one rescan allowed at a time, turning
offload_enabled on/off should not be racy. Each handler queues up a
rescan if one is already in progress.
- For timing diagram, offload_enabled is initially off due to a change
(transformation: splitmirror/remirror), ...
T0 - I/O completion with UA 0x3f 0x0e sets rescan flag.
T1 - rescan worker thread starts a rescan.
T2 - event comes in
T3 - event thread starts and issues "Acknowledge" message
...
T6 - rescan thread has bypassed code to reload new raid map.
...
T7 - event thread runs and sets offload_to_be_enabled
...
T9 - rescan thread turns on offload_enabled.
T10- request comes in and goes down ioaccel path.
T11- BUG_ON.
- After the patch is applied, ioaccel_enabled can only be re-enabled in
the re-scan thread.
Link: https://lore.kernel.org/r/158472877894.14200.7077843399036368335.stgit@brunhilda Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Matt Perricone <matt.perricone@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
libiscsi calls the check_protection transport handler only if SCSI-Respose
is received. So, the handler is never called if iSCSI task is completed
for some other reason like a timeout or error handling. And this behavior
looks correct. But the iSER does not handle this case properly because it
puts a non-checked signature MR to the free pool. Then the error occurs at
reusing the MR because it is not allowed to invalidate a signature MR
without checking.
This commit adds an extra check to iser_unreg_mem_fastreg(), which is a
part of the task cleanup flow. Now the signature MR is checked there if it
is needed.
The RXE driver doesn't set sys_image_guid and user space applications see
zeros. This causes to pyverbs tests to fail with the following traceback,
because the IBTA spec requires to have valid sys_image_guid.
Traceback (most recent call last):
File "./tests/test_device.py", line 51, in test_query_device
self.verify_device_attr(attr)
File "./tests/test_device.py", line 74, in verify_device_attr
assert attr.sys_image_guid != 0
In order to fix it, set sys_image_guid to be equal to node_guid.
I noticed that fsfreeze can take a very long time to freeze an XFS if
there happens to be a GETFSMAP caller running in the background. I also
happened to notice the following in dmesg:
These two things appear to be related. The assertion trips when another
thread initiates a fsmap request (which uses an empty transaction) after
the freezer waited for m_active_trans to hit zero but before the the
freezer executes the WARN_ON just prior to calling xfs_log_quiesce.
The lengthy delays in freezing happen because the freezer calls
xfs_wait_buftarg to clean out the buffer lru list. Meanwhile, the
GETFSMAP caller is continuing to grab and release buffers, which means
that it can take a very long time for the buffer lru list to empty out.
We fix both of these races by calling sb_start_write to obtain freeze
protection while using empty transactions for GETFSMAP and for metadata
scrubbing. The other two users occur during mount, during which time we
cannot fs freeze.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the brcmf_fws_process_skb() fails to get hanger slot for
queuing the skb, it tries to free the skb.
But the caller brcmf_netdev_start_xmit() of that funciton frees
the packet on error return value.
This causes the double freeing and which caused the kernel crash.
Calling nvme_sysfs_delete() when the controller is in the middle of
creation may cause several bugs. If the controller is in NEW state we
remove delete_controller file and don't delete the controller. The user
will not be able to use nvme disconnect command on that controller again,
although the controller may be active. Other bugs may happen if the
controller is in the middle of create_ctrl callback and
nvme_do_delete_ctrl() starts. For example, freeing I/O tagset at
nvme_do_delete_ctrl() before it was allocated at create_ctrl callback.
To fix all those races don't allow the user to delete the controller
before it was fully created.
Signed-off-by: Israel Rukshin <israelr@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case nvme_sysfs_delete() is called by the user before taking the ctrl
reference count, the ctrl may be freed during the creation and cause the
bug. Take the reference as soon as the controller is externally visible,
which is done by cdev_device_add() in nvme_init_ctrl(). Also take the
reference count at the core layer instead of taking it on each transport
separately.
Signed-off-by: Israel Rukshin <israelr@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nvme multipath error handling defaults to controller reset if the
error is unknown. There are, however, no existing nvme status codes that
indicate a reset should be used, and resetting causes unnecessary
disruption to the rest of IO.
Change nvme's error handling to first check if failover should happen.
If not, let the normal error handling take over rather than reset the
controller.
Based-on-a-patch-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: John Meneghini <johnm@netapp.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This changes kcmp_epoll_target to use the new exec_update_mutex
instead of cred_guard_mutex.
This should be safe, as the credentials are only used for reading,
and furthermore ->mm and ->sighand are updated on execve,
but only under the new exec_update_mutex.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Additionally fixes a compile problem in get_syscall_info.c,
observed with gcc-4.8.4:
get_syscall_info.c: In function 'get_syscall_info':
get_syscall_info.c:93:3: error: 'for' loop initial declarations are only
allowed in C99 mode
for (unsigned int i = 0; i < ARRAY_SIZE(args); ++i) {
^
get_syscall_info.c:93:3: note: use option -std=c99 or -std=gnu99 to compile
your code
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a deadlock in the tracer when tracing a multi-threaded
application that calls execve while more than one thread are running.
I observed that when running strace on the gcc test suite, it always
blocks after a while, when expect calls execve, because other threads
have to be terminated. They send ptrace events, but the strace is no
longer able to respond, since it is blocked in vm_access.
The deadlock is always happening when strace needs to access the
tracees process mmap, while another thread in the tracee starts to
execve a child process, but that cannot continue until the
PTRACE_EVENT_EXIT is handled and the WIFEXITED event is received:
This changes mm_access to use the new exec_update_mutex
instead of cred_guard_mutex.
This patch is based on the following patch by Eric W. Biederman:
"[PATCH 0/5] Infrastructure to allow fixing exec deadlocks" Link: https://lore.kernel.org/lkml/87v9ne5y4y.fsf_-_@x220.int.ebiederm.org/ Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cred_guard_mutex is problematic as it is held over possibly
indefinite waits for userspace. The possible indefinite waits for
userspace that I have identified are: The cred_guard_mutex is held in
PTRACE_EVENT_EXIT waiting for the tracer. The cred_guard_mutex is
held over "put_user(0, tsk->clear_child_tid)" in exit_mm(). The
cred_guard_mutex is held over "get_user(futex_offset, ...") in
exit_robust_list. The cred_guard_mutex held over copy_strings.
The functions get_user and put_user can trigger a page fault which can
potentially wait indefinitely in the case of userfaultfd or if
userspace implements part of the page fault path.
In any of those cases the userspace process that the kernel is waiting
for might make a different system call that winds up taking the
cred_guard_mutex and result in deadlock.
Holding a mutex over any of those possibly indefinite waits for
userspace does not appear necessary. Add exec_update_mutex that will
just cover updating the process during exec where the permissions and
the objects pointed to by the task struct may be out of sync.
The plan is to switch the users of cred_guard_mutex to
exec_update_mutex one by one. This lets us move forward while still
being careful and not introducing any regressions.
If '-o' was used more than 64 times in a single invocation of gpio-hammer,
this could lead to an overflow of the 'lines' array. This commit fixes
this by avoiding the overflow and giving a proper diagnostic back to the
user
The patch avoids allocating cpufreq_policy on stack hence fixing frame
size overflow in 'powernv_cpufreq_work_fn'
Fixes: 227942809b52 ("cpufreq: powernv: Restore cpu frequency to policy->cur on unthrottling") Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com> Reviewed-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200316135743.57735-1-psampat@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[ 614.050361] net eth0: DMA Tx error 0x174019
[ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[ 614.135428] 3 locks held by kworker/u4:4/40:
[ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[ 614.177528] #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[ 614.209033] #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[ 614.260854] Hardware name: ARM Test FPGA (DT)
[ 614.274734] Workqueue: rpciod rpc_async_schedule
[ 614.289022] Call trace:
[ 614.296871] dump_backtrace+0x0/0x1a0
[ 614.308311] show_stack+0x14/0x20
[ 614.318751] dump_stack+0xbc/0x100
[ 614.329403] ___might_sleep+0xf0/0x140
[ 614.341018] __might_sleep+0x4c/0x80
[ 614.352201] __mutex_lock+0x5c/0x8a8
[ 614.363348] mutex_lock_nested+0x1c/0x28
[ 614.375654] axienet_dma_err_handler+0x38/0x388
[ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8
[ 614.405894] tasklet_action+0x24/0x30
[ 614.417297] efi_header_end+0xe0/0x494
[ 614.429020] irq_exit+0xd0/0xd8
[ 614.439047] __handle_domain_irq+0x60/0xb0
[ 614.451877] gic_handle_irq+0xdc/0x2d0
[ 614.463486] el1_irq+0xcc/0x180
[ 614.473451] __tcp_transmit_skb+0x41c/0xb58
[ 614.486513] tcp_write_xmit+0x224/0x10a0
[ 614.498792] __tcp_push_pending_frames+0x38/0xc8
[ 614.513126] tcp_rcv_established+0x41c/0x820
[ 614.526301] tcp_v4_do_rcv+0x8c/0x218
[ 614.537784] __release_sock+0x5c/0x108
[ 614.549466] release_sock+0x34/0xa0
[ 614.560318] tcp_sendmsg+0x40/0x58
[ 614.571053] inet_sendmsg+0x40/0x68
[ 614.582061] sock_sendmsg+0x18/0x30
[ 614.593074] xs_sendpages+0x218/0x328
[ 614.604506] xs_tcp_send_request+0xa0/0x1b8
[ 614.617461] xprt_transmit+0xc8/0x4f0
[ 614.628943] call_transmit+0x8c/0xa0
[ 614.640028] __rpc_execute+0xbc/0x6f8
[ 614.651380] rpc_async_schedule+0x28/0x48
[ 614.663846] process_one_work+0x298/0x6a8
[ 614.676299] worker_thread+0x40/0x490
[ 614.687687] kthread+0x134/0x138
[ 614.697804] ret_from_fork+0x10/0x18
[ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we have an error while processing the reloc roots we could leak roots
that were added to rc->reloc_roots before we hit the error. We could
have also not removed the reloc tree mapping from our rb_tree, so clean
up any remaining nodes in the reloc root rb_tree.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ use rbtree_postorder_for_each_entry_safe ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We previously were checking if the root had a dead root before accessing
root->reloc_root in order to avoid a use-after-free type bug. However
this scenario happens after we've unset the reloc control, so we would
have been saved if we'd simply checked for fs_info->reloc_control. At
this point during relocation we no longer need to be creating new reloc
roots, so simply move this check above the reloc_root checks to avoid
any future races and confusion.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
apic->lapic_timer.timer was initialized with HRTIMER_MODE_ABS_HARD but
started later with HRTIMER_MODE_ABS, which may cause the following warning
in PREEMPT_RT kernel.
If the common register memory resource is not available the driver needs
to fail gracefully to disable PM. Instead of returning the error
directly store it in ret and use the already existing error path.
../kernel/trace/trace.c:9335:33: warning: array comparison always
evaluates to true [-Wtautological-compare]
if (__stop___trace_bprintk_fmt != __start___trace_bprintk_fmt)
^
1 warning generated.
These are not true arrays, they are linker defined symbols, which are
just addresses. Using the address of operator silences the warning and
does not change the runtime result of the check (tested with some print
statements compiled in with clang + ld.lld and gcc + ld.bfd in QEMU).
If the opp table specifies opp-supported-hw as a property but the driver
has not set a supported hardware value the OPP subsystem will reject
all the table entries.
Set a "default" value that will match the default table entries but not
conflict with any possible real bin values. Also fix a small memory leak
and free the buffer allocated by nvmem_cell_read().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On P9 DD2.2 due to a CPU defect some TM instructions need to be emulated by
KVM. This is handled at first by the hardware raising a softpatch interrupt
when certain TM instructions that need KVM assistance are executed in the
guest. Althought some TM instructions per Power ISA are invalid forms they
can raise a softpatch interrupt too. For instance, 'tresume.' instruction
as defined in the ISA must have bit 31 set (1), but an instruction that
matches 'tresume.' PO and XO opcode fields but has bit 31 not set (0), like
0x7cfe9ddc, also raises a softpatch interrupt. Similarly for 'treclaim.'
and 'trechkpt.' instructions with bit 31 = 0, i.e. 0x7c00075c and
0x7c0007dc, respectively. Hence, if a code like the following is executed
in the guest it will raise a softpatch interrupt just like a 'tresume.'
when the TM facility is enabled ('tabort. 0' in the example is used only
to enable the TM facility):
int main() { asm("tabort. 0; .long 0x7cfe9ddc;"); }
Currently in such a case KVM throws a complete trace like:
and then treats the executed instruction as a 'nop'.
However the POWER9 User's Manual, in section "4.6.10 Book II Invalid
Forms", informs that for TM instructions bit 31 is in fact ignored, thus
for the TM-related invalid forms ignoring bit 31 and handling them like the
valid forms is an acceptable way to handle them. POWER8 behaves the same
way too.
This commit changes the handling of the cases here described by treating
the TM-related invalid forms that can generate a softpatch interrupt
just like their valid forms (w/ bit 31 = 1) instead of as a 'nop' and by
gently reporting any other unrecognized case to the host and treating it as
illegal instruction instead of throwing a trace and treating it as a 'nop'.
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com> Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org> Acked-By: Michael Neuling <mikey@neuling.org> Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some versions of Intel TH have an issue that prevents the multi mode of
MSU from working correctly, resulting in no trace data and potentially
stuck MSU pipeline.
Disable multi mode on such devices.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200317062215.15598-2-alexander.shishkin@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not free the timewait_info without also holding the
id_priv->lock. Simplify this entire flow by making the free unconditional
during cm_destroy_id() and removing the confusing special case error
unwind during creation of the timewait_info.
This also fixes a leak of the timewait if cm_destroy_id() is called in
IB_CM_ESTABLISHED with an XRC TGT QP. The state machine will be left in
ESTABLISHED while it needed to transition through IB_CM_TIMEWAIT to
release the timewait pointer.
Also fix a leak of the timewait_info if the caller mis-uses the API and
does ib_send_cm_reqs().
Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation") Link: https://lore.kernel.org/r/20200310092545.251365-4-leon@kernel.org Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In NFSv4, the lock stateids are tied to the lockowner, and the open stateid,
so that the action of closing the file also results in either an automatic
loss of the locks, or an error of the form NFS4ERR_LOCKS_HELD.
In practice this means we must not add new locks to the open stateid
after the close process has been invoked. In fact doing so, can result
in the following panic:
The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Both RTC IRQs are requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.
To fix this issue, allocating the rtc_device struct before requesting
the IRQs using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.
Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.
This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM") Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Acked-by: Nayna Jain <nayna@linux.ibm.com> Tested-by: Nayna Jain <nayna@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In xchk_dir_actor, we attempt to validate the directory hash structures
by performing a directory entry lookup by (hashed) name. If the lookup
returns ENOENT, that means that the hash information is corrupt. The
_process_error functions don't catch this, so we have to add that
explicitly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we decide that a directory free block is corrupt, we must take care
not to leak a buffer pointer to the caller. After xfs_trans_brelse
returns, the buffer can be freed or reused, which means that we have to
set *bpp back to NULL.
Callers are supposed to notice the nonzero return value and not use the
buffer pointer, but we should code more defensively, even if all current
callers handle this situation correctly.
Fixes: de14c5f541e7 ("xfs: verify free block header fields") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 267897a4708f ("[media] tda10071: implement DVBv5 statistics") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes the occasional adapter panic when sg_reset is issued with -d, -t, -b
and -H flags. Removal of command type HBA_IU_TYPE_SCSI_TM_REQ in
aac_hba_send since iu_type, request_id and fib_flags are not populated.
Device and target reset handlers are made to send TMF commands only when
reset_state is 0.
Link: https://lore.kernel.org/r/1581553771-25796-1-git-send-email-Sagar.Biradar@microchip.com Reviewed-by: Sagar Biradar <Sagar.Biradar@microchip.com> Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com> Signed-off-by: Balsundar P <balsundar.p@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For sdio chip, it need the memory which is kmalloc, if it is
vmalloc from ath10k_mem_value_read, then it have a memory error.
kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so
add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer
which is vmalloc from ath10k_mem_value_read.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 'etm->instructions_sample_period' is less than
'tidq->period_instructions', the function cs_etm__sample() cannot handle
this case properly with its logic.
Let's see below flow as an example:
- If we set itrace option '--itrace=i4', then function cs_etm__sample()
has variables with initialized values:
So after handle these two packets, there have below issues:
The first issue is that cs_etm__instr_addr() returns the address within
the current trace sample of the instruction related to offset, so the
offset is supposed to be always unsigned value. But in fact, function
cs_etm__sample() might calculate a negative offset value (in handling
the second packet, the offset is -3) and pass to cs_etm__instr_addr()
with u64 type with a big positive integer.
The second issue is it only synthesizes 2 samples for sample period = 4.
In theory, every packet has 10 instructions so the two packets have
total 20 instructions, 20 instructions should generate 5 samples
(4 x 5 = 20). This is because cs_etm__sample() only calls once
cs_etm__synth_instruction_sample() to generate instruction sample per
range packet.
This patch fixes the logic in function cs_etm__sample(); the basic
idea for handling coming packet is:
- To synthesize the first instruction sample, it combines the left
instructions from the previous packet and the head of the new
packet; then generate continuous samples with sample period;
- At the tail of the new packet, if it has the rest instructions,
these instructions will be left for the sequential sample.
Suggested-by: Mike Leach <mike.leach@linaro.org> Signed-off-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Mike Leach <mike.leach@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Walker <robert.walker@arm.com> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: coresight ml <coresight@lists.linaro.org> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200219021811.20067-4-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If use option '--itrace=iNNN' with Arm CoreSight trace data, perf tool
fails inject instruction samples; the root cause is the packets are only
swapped for branch samples and last branches but not for instruction
samples, so the new coming packets cannot be properly handled for only
synthesizing instruction samples.
To fix this issue, this patch refactors the code with a new function
cs_etm__packet_swap() which is used to swap packets and adds the
condition for instruction samples.
Signed-off-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Mike Leach <mike.leach@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Walker <robert.walker@arm.com> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: coresight ml <coresight@lists.linaro.org> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200219021811.20067-2-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently there are only 10 bytes to store the cpu-topology 'name'
information. Only 10 bytes copied into cluster/thread/core names.
If the cluster ID exceeds 2-digit number, it will result in the data
corruption, and ending up in a dead loop in the parsing routines. The
same applies to the thread names with more that 3-digit number.
This issue was found using the boundary tests under virtualised
environment like QEMU.
Let us increase the buffer to fix such potential issues.
Raven provides retimer feature support that requires i2c interaction in
order to make it work well, all settings required for this configuration
are loaded from the Atom bios which include the i2c address. If the
retimer feature is not available, we should abort the attempt to set
this feature, otherwise, it makes the following line return
I2C_CHANNEL_OPERATION_NO_RESPONSE:
i2c_success = i2c_write(pipe_ctx, slave_address, buffer, sizeof(buffer));
...
if (!i2c_success)
ASSERT(i2c_success);
This ends up causing problems with hotplugging HDMI displays on Raven,
and causes retimer settings to warn like so:
This commit reworks the way that we handle i2c write for retimer in the
way that we abort this configuration if the feature is not available in
the device. For debug sake, we kept a simple log message in case the
retimer is not available.
We need to check for errors when calling cpu_pm_enter() and
cpu_cluster_pm_enter(). And we need to bail out on errors as
otherwise we can enter a deeper idle state when not desired.
I'm not aware of the lack of error handling causing issues yet,
but we need this at least for blocking deeper idle states when
a GPIO instance has pending interrupts.
Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20200304225433.37336-2-tony@atomide.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The memory for global pointer is never freed during normal program
execution, so let's do that in the main function exit as a good
programming practice.
A stray blank line is also removed.
Reported-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: John Garry <john.garry@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: James Clark <james.clark@arm.com> Cc: Joakim Zhang <qiangqing.zhang@nxp.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will@kernel.org> Cc: linuxarm@huawei.com Link: http://lore.kernel.org/lkml/1583406486-154841-2-git-send-email-john.garry@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KCSAN find inode->i_disksize could be accessed concurrently.
BUG: KCSAN: data-race in ext4_mark_iloc_dirty / ext4_write_end
write (marked) to 0xffff8b8932f40090 of 8 bytes by task 66792 on cpu 0:
ext4_write_end+0x53f/0x5b0
ext4_da_write_end+0x237/0x510
generic_perform_write+0x1c4/0x2a0
ext4_buffered_write_iter+0x13a/0x210
ext4_file_write_iter+0xe2/0x9b0
new_sync_write+0x29c/0x3a0
__vfs_write+0x92/0xa0
vfs_write+0xfc/0x2a0
ksys_write+0xe8/0x140
__x64_sys_write+0x4c/0x60
do_syscall_64+0x8a/0x2a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8b8932f40090 of 8 bytes by task 14414 on cpu 1:
ext4_mark_iloc_dirty+0x716/0x1190
ext4_mark_inode_dirty+0xc9/0x360
ext4_convert_unwritten_extents+0x1bc/0x2a0
ext4_convert_unwritten_io_end_vec+0xc5/0x150
ext4_put_io_end+0x82/0x130
ext4_writepages+0xae7/0x16f0
do_writepages+0x64/0x120
__writeback_single_inode+0x7d/0x650
writeback_sb_inodes+0x3a4/0x860
__writeback_inodes_wb+0xc4/0x150
wb_writeback+0x43f/0x510
wb_workfn+0x3b2/0x8a0
process_one_work+0x39b/0x7e0
worker_thread+0x88/0x650
kthread+0x1d4/0x1f0
ret_from_fork+0x35/0x40
The plain read is outside of inode->i_data_sem critical section
which results in a data race. Fix it by adding READ_ONCE().
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The last jump to free_exit in mm_iommu_do_alloc() happens after page
pointers in struct mm_iommu_table_group_mem_t were already converted to
physical addresses. Thus calling put_page() on these physical addresses
will likely crash.
This moves the loop which calculates the pageshift and converts page
struct pointers to physical addresses later after the point when
we cannot fail; thus eliminating the need to convert pointers back.
Fixes: eb9d7a62c386 ("powerpc/mm_iommu: Fix potential deadlock") Reported-by: Jan Kara <jack@suse.cz> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191223060351.26359-1-aik@ozlabs.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
While unlikely the divisor in scale64_check_overflow() could be >= 32bit in
scale64_check_overflow(). do_div() truncates the divisor to 32bit at least
on 32bit platforms.
Use div64_u64() instead to avoid the truncation to 32-bit.
Some controllers have been observed to send zero'd events under some
conditions. This change guards against this condition as well as adding
a trace to facilitate diagnosability of this condition.
Josef reported that his old-and-good Plextor ConvertX M402U video
converter spews lots of WARNINGs on the recent kernels, and it turned
out that the device uses a bulk endpoint for interrupt handling just
like 2250 board.
For fixing it, generalize the check with the proper verification of
the endpoint instead of hard-coded board type check.
In tx_wait_done the ipc payload is copied before the DSP transaction
error code is checked. This might lead to corrupted data in kernel side
even though the error would be handled later. It is also pointless to
copy the data in case of error. So change the order of error check and
copy.
Some released ACPI FW for Huawei boards describes incorrect the port IO
address range for child devices, in that it tells us the IO port max range
is 0x3fff for each child device, which is not correct. The address range
should be [e4:e8) or similar. With this incorrect upper range, the child
device IO port resources overlap.
As such, the kernel thinks that the LPC host serial device is a child of
the IPMI device:
They should both be siblings. Note that these are logical PIO addresses,
which have a direct mapping from the FW IO port ranges.
This shows up as a real issue when we enable CONFIG_KASAN and
CONFIG_DEBUG_TEST_DRIVER_REMOVE - we see use-after-free warnings in the
host removal path:
==================================================================
BUG: KASAN: use-after-free in release_resource+0x38/0xc8
Read of size 8 at addr ffff0026accdbc38 by task swapper/0/1
The issue here is that the kernel created an incorrect parent-child
resource dependency between two devices, and references the false parent
node when deleting the second child device, when it had been deleted
already.
Fix up the child device resources from FW to create proper IO port
resource relationships for broken FW.
Fields in "struct timer_rand_state" could be accessed concurrently.
Lockless plain reads and writes result in data races. Fix them by adding
pairs of READ|WRITE_ONCE(). The data races were reported by KCSAN,
BUG: KCSAN: data-race in add_timer_randomness / add_timer_randomness
write to 0xffff9f320a0a01d0 of 8 bytes by interrupt on cpu 22:
add_timer_randomness+0x100/0x190
add_timer_randomness at drivers/char/random.c:1152
add_disk_randomness+0x85/0x280
scsi_end_request+0x43a/0x4a0
scsi_io_completion+0xb7/0x7e0
scsi_finish_command+0x1ed/0x2a0
scsi_softirq_done+0x1c9/0x1d0
blk_done_softirq+0x181/0x1d0
__do_softirq+0xd9/0x57c
irq_exit+0xa2/0xc0
do_IRQ+0x8b/0x190
ret_from_intr+0x0/0x42
cpuidle_enter_state+0x15e/0x980
cpuidle_enter+0x69/0xc0
call_cpuidle+0x23/0x40
do_idle+0x248/0x280
cpu_startup_entry+0x1d/0x1f
start_secondary+0x1b2/0x230
secondary_startup_64+0xb6/0xc0
no locks held by swapper/22/0.
irq event stamp: 32871382
_raw_spin_unlock_irqrestore+0x53/0x60
_raw_spin_lock_irqsave+0x21/0x60
_local_bh_enable+0x21/0x30
irq_exit+0xa2/0xc0
read to 0xffff9f320a0a01d0 of 8 bytes by interrupt on cpu 2:
add_timer_randomness+0xe8/0x190
add_disk_randomness+0x85/0x280
scsi_end_request+0x43a/0x4a0
scsi_io_completion+0xb7/0x7e0
scsi_finish_command+0x1ed/0x2a0
scsi_softirq_done+0x1c9/0x1d0
blk_done_softirq+0x181/0x1d0
__do_softirq+0xd9/0x57c
irq_exit+0xa2/0xc0
do_IRQ+0x8b/0x190
ret_from_intr+0x0/0x42
cpuidle_enter_state+0x15e/0x980
cpuidle_enter+0x69/0xc0
call_cpuidle+0x23/0x40
do_idle+0x248/0x280
cpu_startup_entry+0x1d/0x1f
start_secondary+0x1b2/0x230
secondary_startup_64+0xb6/0xc0
no locks held by swapper/2/0.
irq event stamp: 37846304
_raw_spin_unlock_irqrestore+0x53/0x60
_raw_spin_lock_irqsave+0x21/0x60
_local_bh_enable+0x21/0x30
irq_exit+0xa2/0xc0
Reported by Kernel Concurrency Sanitizer on:
Hardware name: HP ProLiant BL660c Gen9, BIOS I38 10/17/2018
SDEI has private events that need registering and enabling on each CPU.
CPUs can come and go while we are trying to do this. SDEI tries to avoid
these problems by setting the reregister flag before the register call,
so any CPUs that come online register the event too. Sticking plaster
like this doesn't work, as if the register call fails, a CPU that
subsequently comes online will register the event before reregister
is cleared.
Take cpus_read_lock() around the register and enable calls. We don't
want surprise CPUs to do the wrong thing if they race with these calls
failing.
Looks like the iavf code actually experienced a race condition, when a
developer took code before the check for chain 0 was put to helper.
So use tc_cls_can_offload_and_chain0() helper instead of direct check and
move the check to _cb() so this is similar to i40e code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the DSS initialises its output DPI and SDI ports, failures don't
clean up previous successfully initialised ports. This can lead to
resource leak or memory corruption. Fix it.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-22-laurent.pinchart@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Before removing the slave device, disable pm_runtime to prevent any
race condition with the resume being executed after the bus and slave
devices are removed.
Since this pm_runtime_disable() is handled in common routines,
implementations of Slave drivers do not need to call it in their
.remove() routine.
It's incorrect to check the channel's "busy" state without taking a lock.
That shouldn't cause any real troubles, nevertheless it's always better
not to have any race conditions in the code.
If an element is freed via RCU then recursion into BPF instrumentation
functions is not a concern. The element is already detached from the map
and the RCU callback does not hold any locks on which a kprobe, perf event
or tracepoint attached BPF program could deadlock.
Alex Shi reported the pkey macros above arch_set_user_pkey_access()
to be unused. They are unused, and even refer to a nonexistent
CONFIG option.
But, they might have served a good use, which was to ensure that
the code does not try to set values that would not fit in the
PKRU register. As it stands, a too-large 'pkey' value would
be likely to silently overflow the u32 new_pkru_bits.
Add a check to look for overflows. Also add a comment to remind
any future developer to closely examine the types used to store
pkey values if arch_max_pkey() ever changes.
For the duration of mapping eVMCS, it derefences ->memslots without holding
->srcu or ->slots_lock when accessing hv assist page. This patch fixes it by
moving nested_sync_vmcs12_to_shadow to prepare_guest_switch, where the SRCU
is already taken.
It can be reproduced by running kvm's evmcs_test selftest.
=============================
warning: suspicious rcu usage
5.6.0-rc1+ #53 tainted: g w ioe
-----------------------------
./include/linux/kvm_host.h:623 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by evmcs_test/8507:
#0: ffff9ddd156d00d0 (&vcpu->mutex){+.+.}, at:
kvm_vcpu_ioctl+0x85/0x680 [kvm]
This test places a kprobe to function getname_flags() in the kernel
which has the following prototype:
struct filename *getname_flags(const char __user *filename, int flags, int *empty)
The 'filename' argument points to a filename located in user space memory.
Looking at commit 88903c464321c ("tracing/probe: Add ustring type for
user-space string") the kprobe should indicate that user space memory is
accessed.
Output before:
[root@m35lp76 perf]# ./perf test 66 67
66: Use vfs_getname probe to get syscall args filenames : FAILED!
67: Check open filename arg using perf trace + vfs_getname: FAILED!
[root@m35lp76 perf]#
Output after:
[root@m35lp76 perf]# ./perf test 66 67
66: Use vfs_getname probe to get syscall args filenames : Ok
67: Check open filename arg using perf trace + vfs_getname: Ok
[root@m35lp76 perf]#
Comments from Masami Hiramatsu:
This bug doesn't happen on x86 or other archs on which user address
space and kernel address space is the same. On some arches (ppc64 in
this case?) user address space is partially or completely the same as
kernel address space.
(Yes, they switch the world when running into the kernel) In this case,
we need to use different data access functions for each space.
That is why I introduced the "ustring" type for kprobe events.
As far as I can see, Thomas's patch is sane. Thomas, could you show us
your result on your test environment?
Some USB-audio descriptors provide a bogus volume range (e.g. volume
min and max are identical), which confuses user-space.
This patch makes the driver skipping such a control element.
During the cleanup of the aggregation session, a rx handler (or release timer)
on another CPU might still hold a pointer to the reorder buffer and could
attempt to release some packets.
Clearing pointers during cleanup avoids a theoretical use-after-free bug here.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are currently three counters to track the IRQ context of a lock
chain - nr_hardirq_chains, nr_softirq_chains and nr_process_chains.
They are incremented when a new lock chain is added, but they are
not decremented when a lock chain is removed. That causes some of the
statistic counts reported by /proc/lockdep_stats to be incorrect.
IRQ
Fix that by decrementing the right counter when a lock chain is removed.
Since inc_chains() no longer accesses hardirq_context and softirq_context
directly, it is moved out from the CONFIG_TRACE_IRQFLAGS conditional
compilation block.
Fixes: a0b0fd53e1e6 ("locking/lockdep: Free lock classes that are no longer in use") Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lkml.kernel.org/r/20200206152408.24165-2-longman@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_find_matching_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:212:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:237:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sebastian Reichel <sebastian.reichel@collabora.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Cc: Markus Elfring <Markus.Elfring@web.de> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/1554692313-28882-2-git-send-email-wen.yang99@zte.com.cn Signed-off-by: Sasha Levin <sashal@kernel.org>
Coverity reported a memory corruption error for the fdmi attributes
routines:
CID 15768 [Memory Corruption] Out-of-bounds access on FDMI
Sloppy coding of the fmdi structures. In both the lpfc_fdmi_attr_def and
lpfc_fdmi_reg_port_list structures, a field was placed at the start of
payload that may have variable content. The field was given an arbitrary
type (uint32_t). The code then uses the field name to derive an address,
which it used in things such as memset and memcpy. The memset sizes or
memcpy lengths were larger than the arbitrary type, thus coverity reported
an error.
Fix by replacing the arbitrary fields with the real field structures
describing the payload.
Link: https://lore.kernel.org/r/20200128002312.16346-8-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When performing reset testing, the eq's list for related hwqs was getting
corrupted. In cases where there is not a 1:1 eq to hwq, the eq is
shared. The eq maintains a list of hwqs utilizing it in case of cpu
offlining and polling. During the reset, the hwqs are being torn down so
they can be recreated. The recreation was getting confused by seeing a
non-null eq assignment on the eq and the eq list became corrupt.
Correct by clearing the hdwq eq assignment when the hwq is cleaned up.
Link: https://lore.kernel.org/r/20200128002312.16346-6-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:
Port Status Event: ... error 1=0x52004a01, error 2=0x218
The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.
When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.
Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.
[mkp: typo]
Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
$# read after lseek to midle of last line
$ dd if=/sys/fs/selinux/avc/cache_stats bs=180 skip=1
dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset
056 9115 <<<< end of last line 15605711551548 9023 9023 9056 9115 <<< whole last line once again
0+1 records in
0+1 records out
45 bytes copied, 8,7221e-05 s, 516 kB/s
$# read after lseek beyond end of of file
$ dd if=/sys/fs/selinux/avc/cache_stats bs=1000 skip=1
dd: /sys/fs/selinux/avc/cache_stats: cannot skip to specified offset 15605711551548 9023 9023 9056 9115 <<<< generates whole last line
0+1 records in
0+1 records out
36 bytes copied, 9,0934e-05 s, 396 kB/s
Common Criteria calls out for any action that modifies the audit trail to
be recorded. That usually is interpreted to mean insertion or removal of
rules. It is not required to log modification of the inode information
since the watch is still in effect. Additionally, if the rule is a never
rule and the underlying file is one they do not want events for, they
get an event for this bookkeeping update against their wishes.
Since no device/inode info is logged at insertion and no device/inode
information is logged on update, there is nothing meaningful being
communicated to the admin by the CONFIG_CHANGE updated_rules event. One
can assume that the rule was not "modified" because it is still watching
the intended target. If the device or inode cannot be resolved, then
audit_panic is called which is sufficient.
The correct resolution is to drop logging config_update events since
the watch is still in effect but just on another unknown inode.
Signed-off-by: Steve Grubb <sgrubb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log