Chris Morgan [Thu, 12 Aug 2021 13:46:39 +0000 (21:46 +0800)]
arm64: dts: rockchip: Enable SFC for Odroid Go Advance
This enables the Rockchip Serial Flash Controller for the Odroid Go
Advance. Note that while the attached SPI NOR flash and the controller
both support quad read mode, only 2 of the required 4 pins are present.
The rx bus width is set to 2 for this reason, and tx bus width is set
to 1 for compatibility reasons.
The rk356x added a debounce clock to the gpio devices. This clock is
necessary for the new v2 gpio driver to bind.
Add the clocks to the rk356x device tree.
Jianqun Xu [Thu, 5 Aug 2021 12:01:02 +0000 (14:01 +0200)]
soc: rockchip: io-domain: add rk3568 support
The io-domain registers on RK3568 SoCs have three separated bits to
enable/disable the 1.8v/2.5v/3.3v power.
This patch make the write to be a operation, allow rk3568 uses a private
register set function.
Since the 2.5v mode hasn't been fully validated yet, the driver only sets
1.8v [enable] + 3.3v [disable] for 1.8v mode
1.8v [disable] + 3.3v [enable] for 3.3v mode
There is not register order requirement which has been cleared by our IC
team.
For future reference the full usage matrix including the 2.5V setting is:
case V33 V25 V18 result
0 0 0 0 IO safe, but cannot work
1 0 0 1 IO require 1.8V, should < 1.98V, otherwise IO may damage
2 0 1 0 IO require 2.5V, should < 2.75V, otherwise IO may damage
3 0 1 1 Invalid state, should avoid
4 1 0 0 IO require 3.3V, should < 3.63V, otherwise IO may damage
5 1 0 1 IO require 1.8V, should < 1.98V, otherwise IO may damage
6 1 1 0 IO require 2.5V, should < 2.75V, otherwise IO may damage
7 1 1 1 Invalid state, should avoid
Peter Geis [Fri, 30 Jul 2021 15:17:27 +0000 (11:17 -0400)]
arm64: dts: rockchip: add thermal fan control to rockpro64
The rockpro64 had a fan node since
commit 5882d65c1691 ("arm64: dts: rockchip: Add PWM fan for RockPro64")
however it was never tied into the thermal driver for automatic control.
Add the links to the thermal node to permit the kernel to handle this
automatically.
Borrowed from the (rk3399-khadas-edge.dtsi).
Dan Johansen [Thu, 5 Aug 2021 22:04:27 +0000 (00:04 +0200)]
arm64: dts: rockchip: Setup USB typec port as datarole on for Pinebook Pro
Some chargers try to put the charged device into device data
role. Before this commit this condition caused the tcpm state machine to
issue a hard reset due to a capability missmatch.
Chen-Yu Tsai [Thu, 12 Aug 2021 09:47:53 +0000 (17:47 +0800)]
arm64: dts: rockchip: Add gru-scarlet-dumo board
Dumo is another variant of Scarlet, also known as the ASUS Chromebook
Tablet CT100. This is almost the same as Scarlet-Innolux, but uses a
board-specific calibration variant for the WiFi module.
Dumo is another variant of Scarlet, also known as the ASUS Chromebook
Tablet CT100. This is almost the same as Scarlet-Innolux, but uses a
specific calibration variant for the WiFi module.
clk: rockchip: make rk3308 ddrphy4x clock critical
Currently, no driver support for DDR memory controller (DMC) is present,
as a result, no driver is explicitly consuming the ddrphy clock. This means
that VPLL1 (parent of ddr clock) will be shutdown if we enable
and then disable any child clock of VPLL1 (e.g. SCLK_I2S0_8CH_TX).
If VPLL1 is disabled, the whole system will freeze, because the DDR
controller will lose its clock. So, it's necessary to prevent VPLL1 from
shutting down, by marking the ddrphy4x CLK_IS_CRITICAL.
This bug was discovered when I was porting rockchip_i2s_tdm driver to
mainline kernel from Rockchip 4.4 kernel. I guess that other Rockchip
SoCs without DMC driver may need the same patch. If this applies to
other devices, please let us know.
Peter Geis [Wed, 28 Jul 2021 18:00:32 +0000 (14:00 -0400)]
arm64: dts: rockchip: adjust rk3568 pll clocks
The rk3568 gpll should run at 1200mhz and the ppll should run at 200mhz.
These are set incorrectly by the bootloader, so fix them here.
gpll boots at 1188mhz, but to get most accurate dividers for all
gpll_dividers it needs to run at 1200mhz, otherwise everyone downstream
isn't quite right.
ppll feeds the combophys, which has a divide by 2 clock, so 200mhz is
required to reach a 100mhz clock input for them.
Peter Geis [Wed, 28 Jul 2021 18:00:28 +0000 (14:00 -0400)]
clk: rockchip: drop GRF dependency for rk3328/rk3036 pll types
The rk3036/rk3328 pll types were converted to checking the lock status
via the internal register in january 2020, so don't need the grf
reference since then.
But it was forgotten to remove grf check when deciding between the
pll rate ops (read-only vs. read-write), so a clock driver without
the needed grf reference might've been put into the read-only mode
just because the grf reference was missing.
This affected the rk356x that needs to reclock certain plls at boot.
Fix this by removing the check for the grf for selecting the utilized
operations.
Suggested-by: Heiko Stuebner <heiko@sntech.de> Fixes: 7f6ffbb885d1 ("clk: rockchip: convert rk3036 pll type to use internal lock status") Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[adjusted the commit message, adjusted the fixes tag] Link: https://lore.kernel.org/r/20210728180034.717953-3-pgwipeout@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Wed, 10 Feb 2021 11:10:18 +0000 (12:10 +0100)]
arm64: dts: rockchip: add #phy-cells to mipi-dsi1 on rk3399
The dsi controller includes access to the dphy which might be used
not only for dsi output but also for csi input on dsi1, so add the
necessary #phy-cells to allow it to be used as phy.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Tested-by: Sebastian Fricke <sebastian.fricke@posteo.net> Acked-by: Helen Koike <helen.koike@collabora.com> Link: https://lore.kernel.org/r/20210210111020.2476369-5-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Peter Geis [Sat, 10 Jul 2021 15:10:32 +0000 (11:10 -0400)]
arm64: dts: rockchip: split rk3568 device tree
In preparation for the rk3566 inclusion, split apart the rk3568 specific
nodes into a separate device tree.
This allows us to create the rk3566 device tree without deleting nodes.
Peter Geis [Sat, 10 Jul 2021 15:10:31 +0000 (11:10 -0400)]
arm64: dts: rockchip: move rk3568 dtsi to rk356x dtsi
In preparation for separating the rk3568 and rk3566 device trees, move
the base rk3568 dtsi to rk356x dtsi.
This will allow us to strip out the rk3568 specific nodes.
NÃcolas F. R. A. Prado [Thu, 10 Jun 2021 17:56:13 +0000 (14:56 -0300)]
dt-bindings: clk: Convert rockchip,rk3399-cru to DT schema
Convert the rockchip,rk3399-cru binding to DT schema format.
Tested with
ARCH=arm64 make dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml
ARCH=arm64 make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml
Merge tag 'perf-tools-fixes-for-v5.14-2021-07-18' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Skip invalid hybrid PMU on hybrid systems when the atom (little) CPUs
are offlined.
- Fix 'perf test' problems related to the recently added hybrid
(BIG/little) code.
- Split ARM's coresight (hw tracing) decode by aux records to avoid
fatal decoding errors.
- Fix add event failure in 'perf probe' when running 32-bit perf in a
64-bit kernel.
- Fix 'perf sched record' failure when CONFIG_SCHEDSTATS is not set.
- Fix memory and refcount leaks detected by ASAn when running 'perf
test', should be clean of warnings now.
- Remove broken definition of __LITTLE_ENDIAN from tools'
linux/kconfig.h, which was breaking the build in some systems.
- Cast PTHREAD_STACK_MIN to int as it may turn into 'long
sysconf(__SC_THREAD_STACK_MIN_VALUE), breaking the build in some
systems.
- Fix libperf build error with LIBPFM4=1.
- Sync UAPI files changed by the memfd_secret new syscall.
* tag 'perf-tools-fixes-for-v5.14-2021-07-18' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (35 commits)
perf sched: Fix record failure when CONFIG_SCHEDSTATS is not set
perf probe: Fix add event failure when running 32-bit perf in a 64-bit kernel
perf data: Close all files in close_dir()
perf probe-file: Delete namelist in del_events() on the error path
perf test bpf: Free obj_buf
perf trace: Free strings in trace__parse_events_option()
perf trace: Free syscall tp fields in evsel->priv
perf trace: Free syscall->arg_fmt
perf trace: Free malloc'd trace fields on exit
perf lzma: Close lzma stream on exit
perf script: Fix memory 'threads' and 'cpus' leaks on exit
perf script: Release zstd data
perf session: Cleanup trace_event
perf inject: Close inject.output on exit
perf report: Free generated help strings for sort option
perf env: Fix memory leak of cpu_pmu_caps
perf test maps__merge_in: Fix memory leak of maps
perf dso: Fix memory leak in dso__new_map()
perf test event_update: Fix memory leak of unit
perf test event_update: Fix memory leak of evlist
...
Merge tag 'xfs-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"A few fixes for issues in the new online shrink code, additional
corrections for my recent bug-hunt w.r.t. extent size hints on
realtime, and improved input checking of the GROWFSRT ioctl.
IOW, the usual 'I somehow got bored during the merge window and
resumed auditing the farther reaches of xfs':
- Fix shrink eligibility checking when sparse inode clusters enabled
- Reset '..' directory entries when unlinking directories to prevent
verifier errors if fs is shrinked later
- Don't report unusable extent size hints to FSGETXATTR
- Don't warn when extent size hints are unusable because the sysadmin
configured them that way
- Fix insufficient parameter validation in GROWFSRT ioctl
- Fix integer overflow when adding rt volumes to filesystem"
* tag 'xfs-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: detect misaligned rtinherit directory extent size hints
xfs: fix an integer overflow error in xfs_growfs_rt
xfs: improve FSGROWFSRT precondition checking
xfs: don't expose misaligned extszinherit hints to userspace
xfs: correct the narrative around misaligned rtinherit/extszinherit dirs
xfs: reset child dir '..' entry when unlinking child
xfs: check for sparse inode clusters that cross new EOAG when shrinking
Merge tag 'iomap-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull iomap fixes from Darrick Wong:
"A handful of bugfixes for the iomap code.
There's nothing especially exciting here, just fixes for UBSAN (not
KASAN as I erroneously wrote in the tag message) warnings about
undefined behavior in the SEEK_DATA/SEEK_HOLE code, and some
reshuffling of per-page block state info to fix some problems with
gfs2.
- Fix KASAN warnings due to integer overflow in SEEK_DATA/SEEK_HOLE
- Fix assertion errors when using inlinedata files on gfs2"
* tag 'iomap-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: Don't create iomap_page objects in iomap_page_mkwrite_actor
iomap: Don't create iomap_page objects for inline files
iomap: Permit pages without an iop to enter writeback
iomap: remove the length variable in iomap_seek_hole
iomap: remove the length variable in iomap_seek_data
Merge tag 'kbuild-fixes-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Restore the original behavior of scripts/setlocalversion when
LOCALVERSION is set to empty.
- Show Kconfig prompts even for 'make -s'
- Fix the combination of COFNIG_LTO_CLANG=y and CONFIG_MODVERSIONS=y
for older GNU Make versions
* tag 'kbuild-fixes-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Documentation: Fix intiramfs script name
Kbuild: lto: fix module versionings mismatch in GNU make 3.X
kbuild: do not suppress Kconfig prompts for silent build
scripts/setlocalversion: fix a bug when LOCALVERSION is empty
Robert Richter [Thu, 15 Jul 2021 09:26:02 +0000 (11:26 +0200)]
Documentation: Fix intiramfs script name
Documentation was not changed when renaming the script in commit 80e715a06c2d ("initramfs: rename gen_initramfs_list.sh to
gen_initramfs.sh"). Fixing this.
Basically does:
$ sed -i -e s/gen_initramfs_list.sh/gen_initramfs.sh/g $(git grep -l gen_initramfs_list.sh)
Fixes: 80e715a06c2d ("initramfs: rename gen_initramfs_list.sh to gen_initramfs.sh") Signed-off-by: Robert Richter <rrichter@amd.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Kbuild: lto: fix module versionings mismatch in GNU make 3.X
When building modules(CONFIG_...=m), I found some of module versions
are incorrect and set to 0.
This can be found in build log for first clean build which shows
WARNING: EXPORT symbol "XXXX" [drivers/XXX/XXX.ko] version generation failed,
symbol will not be versioned.
But in second build(incremental build), the WARNING disappeared and the
module version becomes valid CRC and make someone who want to change
modules without updating kernel image can't insert their modules.
The problematic code is
+ $(foreach n, $(filter-out FORCE,$^), \
+ $(if $(wildcard $(n).symversions), \
+ ; cat $(n).symversions >> $@.symversions))
`foreach n` shows nothing to `cat` into $(n).symversions because
`if $(wildcard $(n).symversions)` return nothing, but actually
they do exist during this line was executed.
-rw-r--r-- 1 root root 168580 Jun 13 19:10 fs/notify/fsnotify.o
-rw-r--r-- 1 root root 111 Jun 13 19:10 fs/notify/fsnotify.o.symversions
The reason is the $(n).symversions are generated at runtime, but
Makefile wildcard function expends and checks the file exist or not
during parsing the Makefile.
Thus fix this by use `test` shell command to check the file
existence in runtime.
Rebase from both:
1. [https://lore.kernel.org/lkml/20210616080252.32046-1-lecopzer.chen@mediatek.com/]
2. [https://lore.kernel.org/lkml/20210702032943.7865-1-lecopzer.chen@mediatek.com/]
kbuild: do not suppress Kconfig prompts for silent build
When a new CONFIG option is available, Kbuild shows a prompt to get
the user input.
$ make
[ snip ]
Core Scheduling for SMT (SCHED_CORE) [N/y/?] (NEW)
This is the only interactive place in the build process.
Commit 174a1dcc9642 ("kbuild: sink stdout from cmd for silent build")
suppressed Kconfig prompts as well because syncconfig is invoked by
the 'cmd' macro. You cannot notice the fact that Kconfig is waiting
for the user input.
Use 'kecho' to show the equivalent short log without suppressing stdout
from sub-make.
scripts/setlocalversion: fix a bug when LOCALVERSION is empty
The commit 042da426f8eb ("scripts/setlocalversion: simplify the short
version part") reduces indentation. Unfortunately, it also changes behavior
in a subtle way - if the user has empty "LOCALVERSION" variable, the plus
sign is appended to the kernel version. It wasn't appended before.
This patch reverts to the old behavior - we append the plus sign only if
the LOCALVERSION variable is not set.
Fixes: 042da426f8eb ("scripts/setlocalversion: simplify the short version part") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Yang Jihong [Tue, 13 Jul 2021 11:23:58 +0000 (19:23 +0800)]
perf sched: Fix record failure when CONFIG_SCHEDSTATS is not set
The tracepoints trace_sched_stat_{wait, sleep, iowait} are not exposed to user
if CONFIG_SCHEDSTATS is not set, "perf sched record" records the three events.
As a result, the command fails.
Error: File /sys/kernel/tracing/events/sched/sched_stat_wait not found.
Hint: Perhaps this kernel misses some CONFIG_ setting to enable this feature?.
Run 'perf list' for a list of valid events
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-e, --event <event> event selector. use 'perf list' to list available events
Solution:
Check whether schedstat tracepoints are exposed. If no, these events are not recorded.
After:
# perf sched record sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.163 MB perf.data (1091 samples) ]
# perf sched report
run measurement overhead: 4736 nsecs
sleep measurement overhead: 9059979 nsecs
the run test took 999854 nsecs
the sleep test took 8945271 nsecs
nr_run_events: 716
nr_sleep_events: 785
nr_wakeup_events: 0
...
------------------------------------------------------------
Fixes: 2a09b5de235a6 ("sched/fair: do not expose some tracepoints to user if CONFIG_SCHEDSTATS is not set") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Yafang Shao <laoar.shao@gmail.com> Link: http://lore.kernel.org/lkml/20210713112358.194693-1-yangjihong1@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Yang Jihong [Thu, 15 Jul 2021 06:37:23 +0000 (14:37 +0800)]
perf probe: Fix add event failure when running 32-bit perf in a 64-bit kernel
The "address" member of "struct probe_trace_point" uses long data type.
If kernel is 64-bit and perf program is 32-bit, size of "address"
variable is 32 bits.
As a result, upper 32 bits of address read from kernel are truncated, an
error occurs during address comparison in kprobe_warn_out_range().
Before:
# perf probe -a schedule
schedule is out of .text, skip it.
Error: Failed to add events.
Solution:
Change data type of "address" variable to u64 and change corresponding
address printing and value assignment.
After:
# perf.new.new probe -a schedule
Added new event:
probe:schedule (on schedule)
Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Frank Ch. Eigler <fche@redhat.com> Cc: Ian Rogers <irogers@google.com> Cc: Jianlin Lv <jianlin.lv@arm.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Li Huafei <lihuafei1@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Link: http://lore.kernel.org/lkml/20210715063723.11926-1-yangjihong1@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Alex Bee [Fri, 18 Jun 2021 18:12:56 +0000 (20:12 +0200)]
arm64: dts: rockchip: add SPDIF node for ROCK Pi 4
Add a SPDIF audio-graph-card to ROCK Pi 4 device tree.
It's not enabled by default since all dma channels are used by
the (already) enabled i2s0/1/2 and the pin is muxed with GPIO4_C5
which might be in use already.
If enabled SPDIF_TX will be available at pin #15.
Alex Bee [Fri, 18 Jun 2021 18:12:54 +0000 (20:12 +0200)]
arm64: dts: rockchip: Add RK3399 ROCK Pi 4B+ board
ROCK Pi 4B+ board is the successor of ROCK Pi 4B board.
Differences to the original version are
- has RK3399 OP1 SoC revision
- has eMMC (16 or 32 GB) soldered on board (no changes required,
since it is enabled in rk3399-rock-pi-4.dtsi)
- dev boards have SPI flash soldered, but as per manufacturer response,
this won't be the case for mass production boards
Alex Bee [Fri, 18 Jun 2021 18:12:53 +0000 (20:12 +0200)]
arm64: dts: rockchip: Add RK3399 ROCK Pi 4A+ board
ROCK Pi 4A+ board is the successor of ROCK Pi 4A board.
Differences to the original version are
- has RK3399 OP1 SoC revision
- has eMMC (16 or 32 GB) soldered on board (no changes required,
since it is enabled in rk3399-rock-pi-4.dtsi)
- dev boards have SPI flash soldered, but as per manufacturer response,
this won't be the case for mass production boards
arm64: dts: rockchip: Disable CDN DP on Pinebook Pro
The CDN DP needs a PHY and a extcon to work correctly. But no extcon is
provided by the device-tree, which leads to an error:
cdn-dp fec00000.dp: [drm:cdn_dp_probe [rockchipdrm]] *ERROR* missing extcon or phy
cdn-dp: probe of fec00000.dp failed with error -22
Disable the CDN DP to make graphic work on the Pinebook Pro.
It's not clear why, but it causes unexplained problems in entirely
unrelated xfs code. The most likely explanation is some slab
corruption, possibly triggered due to CONFIG_SLUB_DEBUG_ON. See [1].
It ends up having a few other problems too, like build errors on
arch/arc, and Geert reporting it using much more memory on m68k [3] (it
probably does so elsewhere too, but it is probably just more noticeable
on m68k).
The architecture issues (both build and memory use) are likely just
because this change effectively force-enabled STACKDEPOT (along with a
very bad default value for the stackdepot hash size). But together with
the xfs issue, this all smells like "this commit was not ready" to me.
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One core fix for an oops which can occur if the error handling thread
fails to start for some reason and the driver is removed.
The other fixes are all minor ones in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Add missing host_lock in ufshcd_vops_setup_xfer_req()
scsi: mpi3mr: Fix W=1 compilation warnings
scsi: pm8001: Clean up kernel-doc and comments
scsi: zfcp: Report port fc_security as unknown early during remote cable pull
scsi: core: Fix bad pointer dereference when ehandler kthread is invalid
scsi: fas216: Fix a build error
scsi: core: Fix the documentation of the scsi_execute() time parameter
Merge tag '5.14-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Eight cifs/smb3 fixes, including three for stable.
Three are DFS related fixes, and two to fix problems pointed out by
static checkers"
* tag '5.14-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: do not share tcp sessions of dfs connections
SMB3.1.1: fix mount failure to some servers when compression enabled
cifs: added WARN_ON for all the count decrements
cifs: fix missing null session check in mount
cifs: handle reconnect of tcon when there is no cached dfs referral
cifs: fix the out of range assignment to bit fields in parse_server_interfaces
cifs: Do not use the original cruid when following DFS links for multiuser mounts
cifs: use the expiry output of dns_query to schedule next resolution
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan:
"Fixes to kunit tool and documentation:
- fix asserts on older python versions
- fixes to misleading error messages when TAP header format is
incorrect or when file is missing
- documentation fix: drop obsolete information about uml_abort
coverage
- remove unnecessary annotations"
* tag 'linux-kselftest-kunit-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: Assert the version requirement
kunit: tool: remove unnecessary "annotations" import
Documentation: kunit: drop obsolete note about uml_abort for coverage
kunit: tool: Fix error messages for cases of no tests and wrong TAP header
Merge tag 'linux-kselftest-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"A fix to memory-hotplug hot-remove test to stop spamming logs with
dump_page() entries and slowing the system down to a crawl"
* tag 'linux-kselftest-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: memory-hotplug: avoid spamming logs with dump_page(), ratio limit hot-remove error test
Merge tag 'trace-v5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix the histogram logic from possibly crashing the kernel
Working on the histogram code, I found that if you dereference a char
pointer in a trace event that happens to point to user space, it can
crash the kernel, as it does no checks of that pointer. I have code
coming that will do this better, so just remove this ability to treat
character pointers in trace events as stings in the histogram"
* tag 'trace-v5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not reference char * as a string in histograms
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The bulk of the diffstat consists of changes to our uaccess routines
so that they fall back to bytewise copying prior to reporting complete
failure when the initial (multi-byte) access faults.
However, the most disappointing change here is that we've had to bump
ARCH_DMA_MINALIGN back to 128 bytes thanks to Qualcomm's "Kryo" CPU,
which ended up in the MSM8996 mobile SoC. Still, at least we're now
aware of this design and one of the hardware designers confirmed the
L2 cacheline size for us.
Summary:
- Fix instrumentation annotations for entry code
- Ensure kernel MTE state is restored correctly on resume from suspend
- Fix MTE fault from new strlen() routine
- Fallback to byte-wise accesses on initial uaccess fault
- Bump Clang requirement for BTI
- Revert ARCH_DMA_MINALIGN back to 128 bytes (shakes fist at Qualcomm)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: entry: fix KCOV suppression
arm64: entry: add missing noinstr
arm64: mte: fix restoration of GCR_EL1 from suspend
arm64: Avoid premature usercopy failure
arm64: Restrict ARM64_BTI_KERNEL to clang 12.0.0 and newer
Revert "arm64: cache: Lower ARCH_DMA_MINALIGN to 64 (L1_CACHE_BYTES)"
arm64: Add missing header <asm/smp.h> in two files
arm64: fix strlen() with CONFIG_KASAN_HW_TAGS
Stefan Wahren [Sat, 10 Jul 2021 11:04:55 +0000 (13:04 +0200)]
ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in
The usage of usb-nop-xceiv PHY on Raspberry Pi boards with BCM283x has
been a "regression source" a lot of times. The last case is breakage of
USB mass storage boot has been commit e590474768f1 ("driver core: Set
fw_devlink=on by default") for multi_v7_defconfig. As long as
NOP_USB_XCEIV is configured as module, the dwc2 USB driver defer probing
endlessly and prevent booting from USB mass storage device. So make
the driver built-in as in bcm2835_defconfig and arm64/defconfig.
The platform lost the framebuffer due to a commit solving a
circular dependency in v5.14-rc1, so add it back in by explicitly
selecting the framebuffer.
The U8500 has also gained a few systems using touchscreens from
Cypress, Melfas and Zinitix so add these at the same time as
we're updating the defconfig anyway.
This updates the Versatile Express defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- CONFIG_CMA options were moved around.
- CONFIG_MODULES options were moved around.
- CONFIG_CRYPTO_HW was moved around.
This updates the Versatile defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- The CONFIG_FB_MODE_HELPERS are not needed when using DRM
framebuffer emulation as DRM does.
- The Acorn fonts are removed, the default framebuffer font
works fine. I don't know why this was selected in the first
place or how the Kconfig was altered so it was removed.
This updates the RealView defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- The CONFIG_FB_MODE_HELPERS are not needed when using DRM
framebuffer emulation as DRM does.
- Drop two unused penguin logos.
This updates the Integrator defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- Drop the unused Matrox FB drivers that are only used with
specific PCI cards.
Merge tag 'scmi-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARM SCMI fixes for v5.14
A small set of fixes:
- adding check for presence of probe while registering the driver to
prevent NULL pointer access
- dropping the duplicate check as the driver core already takes care of it
- fix for possible scmi_linux_errmap buffer overflow
- fix to avoid sensor message structure padding
- fix the range check for the maximum number of pending SCMI messages
- fix for various kernel-doc warnings
* tag 'scmi-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix range check for the maximum number of pending messages
firmware: arm_scmi: Avoid padding in sensor message structure
firmware: arm_scmi: Fix kernel doc warnings about return values
firmware: arm_scpi: Fix kernel doc warnings
firmware: arm_scmi: Fix kernel doc warnings
firmware: arm_scmi: Fix possible scmi_linux_errmap buffer overflow
firmware: arm_scmi: Ensure drivers provide a probe function
firmware: arm_scmi: Simplify device probe function on the bus
Merge tag 'arm-ffa-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm FF-A fixes for v5.14
A small set of fixes:
- adding check for presence of probe while registering the driver to
prevent NULL pointer access
- dropping the duplicate check as the driver core already takes care of it
- fixing possible ffa_linux_errmap buffer overflow and
- fixing kernel-doc warning for comment style
* tag 'arm-ffa-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Fix a possible ffa_linux_errmap buffer overflow
firmware: arm_ffa: Fix the comment style
firmware: arm_ffa: Simplify probe function
firmware: arm_ffa: Ensure drivers provide a probe function
Merge tag 'tegra-for-5.14-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.14-rc1
This contains two late fixes for Tegra194 device tree files to restore
USB and audio functionality after enabling system-wide IOMMU support.
* tag 'tegra-for-5.14-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support for USB on Tegra194
arm64: tegra: Enable audio IOMMU support on Tegra194
Merge tag 'renesas-fixes-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.14
- Fix a clock/reset handling design issue on the new RZ/G2L SoC,
requiring an atomic change to DT binding definitions, clock driver,
and DTS,
- Restore graphical consoles in the shmobile_defconfig.
* tag 'renesas-fixes-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: shmobile: defconfig: Restore graphical consoles
dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions
clk: renesas: r9a07g044: Add P2 Clock support
clk: renesas: r9a07g044: Fix P1 Clock
clk: renesas: r9a07g044: Rename divider table
clk: renesas: rzg2l: Add multi clock PM support
Merge tag 'memory-controller-drv-tegra-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/fixes
Memory controller drivers for v5.14 - Tegra SoC, late fixes
Two fixes for recent series of changes in Tegra SoC memory controller
drivers:
1. Add a stub for tegra_mc_probe_device() to fix compile testing of
arm-smmu without TEGRA_MC.
2. Fix arm-smmu dtschema syntax.
* tag 'memory-controller-drv-tegra-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: arm-smmu: Fix json-schema syntax
memory: tegra: Add compile-test stub for tegra_mc_probe_device()
Merge tag 'docs-5.14-2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of fixes in and around documentation.
Some funky quotes in LICENSES/dual/CC-BY-4.0 were giving spdxcheck.py
grief; that has been fixed on both ends. Also a couple of features
updates and one docs build fix"
* tag 'docs-5.14-2' of git://git.lwn.net/linux:
docs/zh_CN: add a missing space character
Documentation/features: Add THREAD_INFO_IN_TASK feature matrix
Documentation/features: Update the ARCH_HAS_TICK_BROADCAST entry
LICENSES/dual/CC-BY-4.0: Git rid of "smart quotes"
scripts/spdxcheck.py: Strictly read license files in utf-8
Merge tag 'block-5.14-2021-07-16' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe fixes via Christoph:
- fix various races in nvme-pci when shutting down just after
probing (Casey Chen)
- fix a net_device leak in nvme-tcp (Prabhakar Kushwaha)
- Fix regression in xen-blkfront by cleaning up the removal state
machine (Christoph)
- Fix tag_set and queue cleanup ordering regression in nbd (Wang)
- Fix tag_set and queue cleanup ordering regression in pd (Guoqing)
* tag 'block-5.14-2021-07-16' of git://git.kernel.dk/linux-block:
xen-blkfront: sanitize the removal state machine
nbd: fix order of cleaning up the queue and freeing the tagset
pd: fix order of cleaning up the queue and freeing the tagset
nvme-pci: do not call nvme_dev_remove_admin from nvme_remove
nvme-pci: fix multiple races in nvme_setup_io_queues
nvme-tcp: use __dev_get_by_name instead dev_get_by_name for OPT_HOST_IFACE
Merge tag 'io_uring-5.14-2021-07-16' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Two small fixes: one fixing the process target of a check, and the
other a minor issue with the drain error handling"
* tag 'io_uring-5.14-2021-07-16' of git://git.kernel.dk/linux-block:
io_uring: fix io_drain_req()
io_uring: use right task for exiting checks
Merge tag 'drm-fixes-2021-07-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular rc2 fixes though a bit more than usual at rc2 stage, people
must have been testing early or else some fixes from last week got a
bit laggy.
There is one larger change in the amd fixes to amalgamate some power
management code on the newer chips with the code from the older chips,
it should only affects chips where support was introduced in rc1 and
it should make future fixes easier to maintain probably a good idea to
merge it now.
Otherwise it's mostly fixes across the board.
dma-buf:
- Fix fence leak in sync_file_merge() error code
drm/panel:
- nt35510: Don't fail on DSI reads
fbdev:
- Avoid use-after-free by not deleting current video mode
ttm:
- Avoid NULL-ptr deref in ttm_range_man_fini()
vmwgfx:
- Fix a merge commit
qxl:
- fix a TTM regression
amdgpu:
- SR-IOV fixes
- RAS fixes
- eDP fixes
- SMU13 code unification to facilitate fixes in the future
- Add new renoir DID
- Yellow Carp fixes
- Beige Goby fixes
- Revert a bunch of TLB fixes that caused regressions
- Revert an LTTPR display regression
amdkfd
- Fix VRAM access regression
- SVM fixes
i915:
- Fix -EDEADLK handling regression
- Drop the page table optimisation"
* tag 'drm-fixes-2021-07-16' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/amdgpu: add another Renoir DID
drm/ttm: add a check against null pointer dereference
drm/i915/gtt: drop the page table optimisation
drm/i915/gt: Fix -EDEADLK handling regression
drm/amd/pm: Add waiting for response of mode-reset message for yellow carp
Revert "drm/amdkfd: Add heavy-weight TLB flush after unmapping"
Revert "drm/amdgpu: Add table_freed parameter to amdgpu_vm_bo_update"
Revert "drm/amdkfd: Make TLB flush conditional on mapping"
Revert "drm/amdgpu: Fix warning of Function parameter or member not described"
Revert "drm/amdkfd: Add memory sync before TLB flush on unmap"
drm/amd/pm: Fix BACO state setting for Beige_Goby
drm/amdgpu: Restore msix after FLR
drm/amdkfd: Allow CPU access for all VRAM BOs
drm/amdgpu/display - only update eDP's backlight level when necessary
drm/amdkfd: handle fault counters on invalid address
drm/amdgpu: Correct the irq numbers for virtual crtc
drm/amd/display: update header file name
drm/amd/pm: drop smu_v13_0_1.c|h files for yellow carp
drm/amd/display: remove faulty assert
Revert "drm/amd/display: Always write repeater mode regardless of LTTPR"
...
projects / users / jedix / linux-maple.git / log