Arnd Bergmann [Tue, 22 Aug 2023 01:23:53 +0000 (21:23 -0400)]
Merge tag 'stm32-dt-for-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.6, round 1
Highlights:
----------
- MCU:
- Add CAN support on stm32f746.
- Add touchscreen support (edt-ft5306) on stm32f746-disco.
- Add support to Rocktech RK043FN48H display on stm32f746-disco
board.
- Add gpio-ranges for stm32f7 to fix boot issue.
- MPU:
- STM32MP13:
- Remove shmem for scmi-optee to match with OP-TEE configuration.
- Enable OP-TEE asynchronous notification by using PPI#15.
- Expose and use SCMI regulators on stm32mp135f-dk.
- STMP32MP15:
- Remove shmem for scmi-optee to match with OPTEE configuration
- Deduplicate DSI node to fix #address-cells/#size-cells issue on
boards using it.
- ST:
- Fix dts check warnings on stm32mp15-scmi boards.
- DH:
- Add missing detach mailbox for DHCOM and DHCOR SoM.
- Odyssey:
- Add missing detach mailbox for Odyssey SoM.
- OCTAVO:
- Add Linux Automation Test Automation Controller (LXA TAC) based
on Octavo Systems OSD32MP15x SiP. It contains: eMMC,
DSA-capable ETH switch (2 ports), dual CAN...
It adds two boards support: lxa-tac-gen1 and lxa-tac-gen2 based
on STM32MP157.
- PROTONIC:
- Add Power over Data Line (PoDL) Power Source Equipment (PSE)
regulator nodes on PRTT1C board. It allows power delivery and
data transmission over a single twisted pair.
* tag 'stm32-dt-for-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (29 commits)
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
ARM: dts: st: Add gpio-ranges for stm32f769-pinctrl
ARM: dts: st: Add gpio-ranges for stm32f746-pinctrl
ARM: dts: st: stm32mp157c-emstamp: correct regulator-active-discharge
ARM: dts: st: stm32mp157c-emstamp: drop incorrect vref_ddr property
ARM: dts: stm32: fix dts check warnings on stm32mp15-scmi
ARM: dts: stm32: Add missing detach mailbox for DHCOR SoM
ARM: dts: stm32: Add missing detach mailbox for DHCOM SoM
ARM: dts: stm32: Add missing detach mailbox for Odyssey SoM
ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon
ARM: dts: stm32: prtt1c: Add PoDL PSE regulator nodes
ARM: dts: stm32: add touchscreen on stm32f746-disco board
ARM: dts: stm32: add pin map for i2c3 controller on stm32f7
ARM: dts: stm32: re-add CAN support on stm32f746
...
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
Since OP-TEE release tag 3.22.0, OP-TEE SCMI service for STM32MP13x
SoC family exposes PMIC voltage regulators. This change defines
them in the platform DTS file and removes the fixed regulators that
were previously defined to abstract them before OP-TEE firmware was
ready.
Updates STM32MP13x SoC DTSI file to define the SoC voltage regulators
exposed by OP-TEE SCMI service and remove the fixed regulator
abstraction previously used until OP-TEE OS firmware embeds the
service which it does since its release tag 3.22.0.
Dario Binacchi [Mon, 14 Aug 2023 13:28:43 +0000 (15:28 +0200)]
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
In the schematics of document UM1907, the power supply for the micro SD
card is the same 3v3 voltage that is used to power other devices on the
board. By generalizing the name of the voltage regulator, it can be
referenced by other nodes in the device tree without creating
misunderstandings.
This patch is preparatory for future developments.
Arnd Bergmann [Mon, 14 Aug 2023 21:43:16 +0000 (23:43 +0200)]
Merge tag 'ti-k3-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt
TI K3 device tree updates for v6.6
New Boards:
- TQ group's TQMaX4XxL AM64 SOM and MBaX4XxL carrier board
- TI's AM62P5 Starter Kit (SK)
New features:
AM625:
- Support for Display (parallel only) - hdmi+audio support for
AM625-SK/BeaglePlay, TC358778 DPI to MIPI-DSI bridge support
for verdin.
- MCU MCAN support and enable of Toradex Verdin
- Toradex Verdin Dahlia audio support
AM62A7:
- MCU MCAN support
- Enable USB Dual Role Device(DRD) support for AM62A7
Starter Kit(SK).
AM64:
- TQ group's tqma64xxl: Overlays for SD-card and wlan.
J721E:
- Main domain CPSW9G and correponding gateway/ethernet
switch expansion - GESI board.
J721S2/AM68:
- New CAN instances, ehrpwm, Display (DSS) and am68-sk HDMI support
- Main domain CPSW2G and correponding gateway/ethernet
switch expansion - GESI board.
J784S4/AM69:
- Boot phase tag marking in device tree
- UFS support
Cleanups and non-urgent fixes:
- Cosmetic style fixups around "=" and "{" whitespace usage.
- Fixups across multiple SoCs/boards for pwm-tbclk to matchup with
bindings
- Serdes header file include/dt-bindings/mux/ti-serdes.h is now
deprecated, use k3-serdes.h in soc dtsi folder.
- All SoCs: Enable GPIO/SDHCI/OSPI/TSADC/C6/C7 DSP nodes at the
board level.
- Fixups for AM62: Crypto powerdomains are conditional to better
represent control of the crypto engines by security controller.
- Fixups for j721e: Duplicate wakeup_i2c node dropped for SoM board.
- Fixups for j721s2/am68: pimux offsets for OSPI.
- Fixups for j784s4/am69: Fixups for pinmux for ospi/adc interrupt
ranges for wkup/main gpios
* tag 'ti-k3-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (68 commits)
arm64: dts: ti: verdin-am62: Add DSI display support
arm64: dts: ti: Add support for the AM62P5 Starter Kit
arm64: dts: ti: Introduce AM62P5 family of SoCs
dt-bindings: arm: ti: Add bindings for AM62P5 SoCs
arm64: dts: ti: k3-am69-sk: Add phase tags marking
arm64: dts: ti: k3-j784s4-evm: Add phase tags marking
arm64: dts: ti: k3-j784s4: Add phase tags marking
arm64: dts: ti: k3-am625-beagleplay: Add HDMI support
arm64: dts: ti: am62x-sk: Add overlay for HDMI audio
arm64: dts: ti: k3-am62x-sk-common: Add HDMI support
arm64: dts: ti: k3-am62-main: Add node for DSS
arm64: dts: ti: k3-am62x-sk-common: Update main-i2c1 frequency
arm64: dts: ti: k3-j721e: Enable C6x DSP nodes at the board level
arm64: dts: ti: k3-j784s4: Enable C7x DSP nodes at the board level
arm64: dts: ti: k3-j721e: Enable C7x DSP nodes at the board level
arm64: dts: ti: k3-*: fix fss node dtbs check warnings
arm64: dts: ti: k3-am64: Enable TSCADC nodes at the board level
arm64: dts: ti: k3-am65: Enable TSCADC nodes at the board level
arm64: dts: ti: k3-j721e: Enable TSCADC nodes at the board level
arm64: dts: ti: k3-j7200: Enable GPIO nodes at the board level
...
Arnd Bergmann [Mon, 14 Aug 2023 21:40:17 +0000 (23:40 +0200)]
Merge tag 'imx-dt64-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX arm64 device tree chanage for 6.6:
- New board device trees: i.MX93 based MBa93xxLA SBC, DEBIX SOM A,
Gateworks i.MX8MM and i.MX8MP Venice boards.
- Add HDMI audio and video support for i.MX8MM/N Beacon board.
- Add coresight trace support for i.MX8MQ SoC.
- Replace deprecated extcon-usb-gpio id-gpio/vbus-gpio properties.
- Add sound card support for verdin-imx8mp devices.
- A couple of change from Frank Li to add CPU frequency table and
thermal support for i.MX8QM SoC.
- Add L1 and L2 cache info for LS1028A SoC.
- A series of i.MX93 changes from Peng Fan t oadd thermal and CM33 core
support.
- A few imx8mq-librem5 updates from Martin Kepplinger and
Sebastian Krzyszkowiak.
- A series of imx8mp-phycore-som changes from Teresa Remmet to update
regulators.
- A bunch of changes from Tim Harvey to update various Gateworks boards.
- A bunch of dtschema warning fixes from Fabio Estevam, Krzysztof
Kozlowski, etc.
- Other small and random changes.
* tag 'imx-dt64-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (88 commits)
arm64: dts: imx8mq-librem5-devkit: Drop power-supply
arm64: dts: imx8mq-librem5-devkit: Mark buck2 as always on
arm64: dts: imx8mm-beacon-baseboard: Remove usbotg2 pinctrl-names
arm64: dts: imx8mm-emcon: Remove iomuxc pinctrl-names
arm64: dts: imx8m-beacon-kit: Remove extra sound-sai entry
arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
arm64: dts: imx8mp-debix: remove unused fec pinctrl node
arm64: dts: imx8mp-debix-model-a: Remove invalid rtc property
arm64: dts: imx8mp-msc-sm2s-ep1: Remove invalid sgtl5000 property
arm64: dts: imx8m-venice: Pass "brcm,bcm4329-fmac"
arm64: dts: imx8mp-evk: Add HDMI support
arm64: dts: freescale: verdin-imx8mp: dev: add sound card
arm64: dts: freescale: verdin-imx8mp: dahlia: add sound card
arm64: dts: imx8mm-emcon: Fix the regulator names
arm64: dts: imx: Pass a single BD71847 clock entry
arm64: dts: ls1028a: add l1 and l2 cache info
arm64: dts: imx8mm-phyboard-polis-rdk: Remove 'fsl,spi-num-chipselects'
arm64: dts: imx8dxl-evk: Remove 'fsl,spi-num-chipselects'
arm64: dts: freescale: Replace deprecated extcon-usb-gpio id-gpio/vbus-gpio properties
arm64: dts: tqma8mqnl: Add vcc supply to i2c eeproms
...
Arnd Bergmann [Mon, 14 Aug 2023 21:38:26 +0000 (23:38 +0200)]
Merge tag 'imx-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree change for 6.6:
- New device tree for TQ-Systems MBLS102xA board.
- A bunch of dtschema warning fixes from Fabio Estevam and
Krzysztof Kozlowski.
- Add missing supply regulator for imx6qdl-mba6 and imx6qdl-tqma6x.
- Replace deprecated extcon-usb-gpio id-gpio/vbus-gpio properties.
- Disable the internal i.MX6 watchdog and rely on PMIC reboot handler
for phycore and pfla02 boards.
- Replace NO_PAD_CTL by explicit pad configuration for karo-tx25 board.
* tag 'imx-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (35 commits)
ARM: dts: imx6qdl: mba6: Fix gpio-keys button node names
ARM: dts: imx6ul: Fix nand-controller #size-cells
ARM: dts: imx6ul: mba6ulx: Fix stmpe811 node warnings
ARM: dts: imx6dl-b1x5pv2: Fix simple-audio routing property
ARM: dts: imx6q-prti6q: Fix the SDIO wifi node
ARM: dts: vfxxx: Pass 'mmc' as the esdhc node names
ARM: dts: imx53-smd: Remove invalid SPI flash entry
ARM: dts: imx50-evk: Use generic node name for SPI NOR flash
ARM: dts: imx6q-cm-fx6: Remove invalid SPI flash entry
ARM: dts: ls1021a: add TQMLS1021A flash partition layout
ARM: dts: ls1021a: add TQ-Systems MBLS102xA device tree
ARM: dts: imx: Remove 'compatible' from the pfuze nodes
ARM: dts: imx: Pass #sound-dai-cells to sgtl5000
ARM: dts: nxp: mxs: split interrupts per cells
ARM: dts: imx6ul-geam: Remove invalid sgtl5000 property
ARM: dts: imx28: drop incorrect reg in fixed regulators
ARM: dts: imx27: drop incorrect reg in fixed regulators
ARM: dts: imx25: drop incorrect reg in fixed regulators
ARM: dts: imx23: drop incorrect reg in fixed regulators
ARM: dts: imx50-kobo-aura: switch to enable-gpios
...
Arnd Bergmann [Mon, 14 Aug 2023 21:08:54 +0000 (23:08 +0200)]
Merge tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.6
StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (26 commits)
riscv: dts: starfive: jh7110: Fix GMAC configuration
riscv: dts: starfive - Add hwrng node for JH7110 SoC
riscv: dts: starfive - Add crypto and DMA node for JH7110
riscv: dts: starfive: Add mmc nodes on VisionFive 2 board
riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060
riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC
riscv: dts: starfive: jh7110: add the node and pins configuration for tdm
riscv: dts: starfive: jh7110: add dma controller node
riscv: dts: starfive: Add spi node and pins configuration
riscv: dts: starfive: Add USB dts node for JH7110
riscv: dts: starfive: Add USB and PCIe PHY nodes for JH7110
riscv: dts: starfive: jh7110: Add temperature sensor node and thermal-zones
riscv: dts: starfive: jh7100: Add temperature sensor node and thermal-zones
riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
riscv: dts: starfive: jh7110: Add ethernet device nodes
riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
riscv: dts: starfive: jh7110: Add syscon nodes
riscv: dts: starfive: jh7110: Add STGCRG/ISPCRG/VOUTCRG nodes
riscv: dts: starfive: jh7110: Add DVP and HDMI TX pixel external clocks
dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
...
Arnd Bergmann [Mon, 14 Aug 2023 17:08:04 +0000 (19:08 +0200)]
Merge tag 'mvebu-dt-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt for 6.6 (part 1)
Fix style issue and incorrect syntax
* tag 'mvebu-dt-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: marvell: dove: drop incorrect reg in fixed regulators
ARM: dts: marvell: armada: drop incorrect reg in fixed regulators
ARM: dts: marvell: add missing space before {
Arnd Bergmann [Mon, 14 Aug 2023 17:07:44 +0000 (19:07 +0200)]
Merge tag 'mvebu-dt64-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into soc/dt
mvebu dt64 for 6.6 (part 1)
Add the NAND Flash Controller on the AC5/AC5X SOC device tree
Fix style issue
* tag 'mvebu-dt64-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: Add NAND flash controller to AC5
arm64: dts: marvell: add missing space before {
Francesco Dolcini [Sat, 12 Aug 2023 19:11:23 +0000 (21:11 +0200)]
arm64: dts: ti: verdin-am62: Add DSI display support
Add MIPI-DSI support to Verdin AM62.
Verdin AM62 has a MIPI DSI interface on the edge connector, this is
provided with a Toshiba TC358778 DPI to MIPI-DSI bridge connected to the
DSS DPI port with a 18-bit width parallel bus.
arch/arm/boot/dts/nuvoton-npcm730-gbs.dtb: i2c-switch@71: $nodename:0: 'i2c-switch@71' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dtb: i2c-switch@70: $nodename:0: 'i2c-switch@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arm/boot/dts/aspeed-bmc-bytedance-g220a.dtb: i2c-switch@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Andrew Davis [Wed, 2 Aug 2023 15:33:31 +0000 (10:33 -0500)]
ARM: dts: nspire: Remove file name from the files themselves
File names inside the file does not add much and just makes it
difficult to move the files, often the file name is not updated
and becomes wrong. Remove them.
Signed-off-by: Andrew Davis <afd@ti.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Andrew Davis [Wed, 2 Aug 2023 15:33:29 +0000 (10:33 -0500)]
ARM: dts: nspire: Fix uart node to conform with DT binding
This node does not follow the DT binding schema, correct this.
The arm,pl011 binding requires the first clock to be named "uartclk".
Should result in no functional change.
Signed-off-by: Andrew Davis <afd@ti.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Andrew Davis [Wed, 2 Aug 2023 15:33:28 +0000 (10:33 -0500)]
ARM: dts: nspire: Fix vbus_reg node to conform with DT binding
This node does not follow the DT binding schema, correct this.
All "regulator-fixed" are voltage type, so drop "regulator-type".
Should result in no functional change.
Signed-off-by: Andrew Davis <afd@ti.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Sat, 12 Aug 2023 08:58:17 +0000 (10:58 +0200)]
Merge tag 'samsung-dt-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.6
1. Galaxy S II: correct LCD screen's physical size.
2. Add Samsung Galaxy Tab 3 8.0 boards (Exynos4212).
3. Galaxy S3 family: add USB connector and USB OTG. Full USB OTG still
seems not to work, but at least HDMI improved and dtbs_check is
happy.
4. Fix issues pointed out by dtbs_check and W=1: unit addresses, use
'gpios' suffix over 'gpio', update i2c-arb device node to newer
binding.
5. Few white-space cleanups.
* tag 'samsung-dt-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: samsung: exynos4412-midas: add USB connector and USB OTG
ARM: dts: samsung: exynos5250-snow: switch i2c-arb to new child variant
ARM: dts: samsung: exynos5250-snow: use 'gpios' suffix for i2c-arb
ARM: dts: samsung: fix Exynos4212 Tab3 makefile entries
ARM: dts: exynos: Add Samsung Galaxy Tab 3 8.0 boards
ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)
ARM: dts: samsung: s3c6410-mini6410: correct ethernet reg addresses (split)
ARM: dts: samsung: exynos4210-i9100: Fix LCD screen's physical size
ARM: dts: s5pv210: minor whitespace cleanup around '='
ARM: dts: exynos: minor whitespace cleanup around '='
Arnd Bergmann [Sat, 12 Aug 2023 08:57:42 +0000 (10:57 +0200)]
Merge tag 'samsung-dt64-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.6
1. Add dedicated compatibles for PWM block.
2. Add PWM to ExynosAutov9 SADK board.
3. Few white-space and other cleanups.
* tag 'samsung-dt64-6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: exynos5433-tm2: drop redundant status=okay
arm64: dts: exynos: add pwm node for exynosautov9-sadk
dt-bindings: pwm: samsung: add exynosautov9 compatible
arm64: dts: fsd: minor whitespace cleanup around '='
arm64: dts: exynos: minor whitespace cleanup around '='
arm64: dts: exynos: add missing space before {
Arnd Bergmann [Sat, 12 Aug 2023 08:56:09 +0000 (10:56 +0200)]
Merge tag 'omap-for-v6.6/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into soc/dt
Devicetree changes for omaps for v6.6
Updates for opp and pinctrl nodes to follow the devicetree bindings.
* tag 'omap-for-v6.6/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dts: ti: omap: Fix OPP table node names
arm: dts: ti: omap: am5729-beagleboneai: Drop the OPP
arm: dts: ti: omap: omap36xx: Rename opp_supply nodename
ARM: dts: ti: add missing space before {
ARM: dts: ti: split interrupts per cells
ARM: dts: Unify pinctrl-single pin group nodes for davinci
Arnd Bergmann [Sat, 12 Aug 2023 08:53:27 +0000 (10:53 +0200)]
Merge tag 'omap-for-v6.6/dt-bindings-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into soc/dt
Devicetree binding changes for omaps for v6.6
Just one change to get started on SoC yaml binding changes for omaps.
* tag 'omap-for-v6.6/dt-bindings-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
dt-bindings: omap: Partially convert omap.txt to yaml
Arnd Bergmann [Sat, 12 Aug 2023 08:46:57 +0000 (10:46 +0200)]
Merge tag 'sunxi-dt-for-6.6-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
- Add D1 GPADC node
- Introduce support for OrangePi Zero 3 SBC
- Enable DT overlay support for Allwinner H3 boards
* tag 'sunxi-dt-for-6.6-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: Enable device-tree overlay support for sun8i-h3 pi devices
arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support
dt-bindings: arm: sunxi: document Orange Pi Zero 3 board name
arm64: dts: allwinner: h616: Split Orange Pi Zero 2 DT
riscv: dts: allwinner: d1: Add GPADC node
Arnd Bergmann [Sat, 12 Aug 2023 08:45:30 +0000 (10:45 +0200)]
Merge tag 'amlogic-arm64-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/dt
Amlogic ARM64 DT changes for v6.6:
- Add initial support for A311D2
- Add AN400 board
- Add gpio_intc, power domain for C3 SoC
- Again some DT bindings fixes & cleanups
* tag 'amlogic-arm64-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: amlogic: drop cooling-[min|max]-state from pwm-fan
arm64: dts: amlogic: meson-g12-common: change aobus-pinctrl node name
arm64: dts: amlogic: meson-g12b-odroid-n2: fix usb hub hog name
arm64: dts: amlogic: drop redundant status=okay in sound nodes
arm64: dts: amlogic: meson-g12b-bananapi: switch to enable-gpios
arm64: dts: add support for C3 power domain controller
arm64: dts: Add gpio_intc node and pinctrl node for Amlogic C3 SoCs
arm64: dts: add board AN400
dt-bindings: arm: amlogic: add board AN400
arm64: dts: amlogic: minor whitespace cleanup around '='
arm64: dts: amlogic-t7-a311d2-khadas-vim4: add initial device-tree
dt-bindings: arm: amlogic: add Amlogic A311D2 bindings
Arnd Bergmann [Sat, 12 Aug 2023 08:44:02 +0000 (10:44 +0200)]
Merge tag 'zynqmp-dt-for-6.6' of https://github.com/Xilinx/linux-xlnx into soc/dt
arm64: ZynqMP DT changes for v6.6
- Describe caches
- Fix i2c gpio recovery description
- Setting up default i2c frequency
- Describe GEM TSU clock and assigned rates for SOMs
- Reserved 1MB for internal firmware usage
- Fix dwc3 IRQ description
- Describe interrupts by using macros
* tag 'zynqmp-dt-for-6.6' of https://github.com/Xilinx/linux-xlnx:
arm64: zynqmp: Describe interrupts by using macros
arm64: zynqmp: Fix dwc3 usb interrupt description
arm64: zynqmp: Add memory reserved node for k26 Kria SOM board
arm64: zynqmp: Assign TSU clock frequency for GEMs
arm64: zynqmp: Setting default i2c clock frequency to 400kHz
arm64: zynqmp: Fix open drain warning on ZynqMP
arm64: zynqmp: Add L2 cache nodes
Arnd Bergmann [Sat, 12 Aug 2023 08:42:44 +0000 (10:42 +0200)]
Merge tag 'hisi-arm64-dt-for-6.6' of https://github.com/hisilicon/linux-hisi into soc/dt
ARM64: DT: HiSilicon ARM64 DT updates for v6.6
- Miscellaneous fixes according the DTS coding style
- Correct the clocks order of the sd0 for the hi3798cv200
* tag 'hisi-arm64-dt-for-6.6' of https://github.com/hisilicon/linux-hisi:
arm64: dts: hi3798cv200: Fix clocks order of sd0
arm64: dts: hisilicon: add missing space before {
arm64: dts: hisilicon: minor whitespace cleanup around '='
Arnd Bergmann [Sat, 12 Aug 2023 08:39:59 +0000 (10:39 +0200)]
Merge tag 'renesas-dts-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.6
- Add Clocked Serial Interface (CSI) support for the RZ/V2M SoC,
- Add PMIC, RTC, and PWM support for the RZ/G2L, RZ/G2LC, and RZ/V2L
SMARC EVK development boards,
- Add PWM (MTU3a) support for the RZ/G2UL and RZ/Five SoCs,
- Add External interrupt (INTC-EX) support for the R-Car S4-8 SoC,
- Add LED support for the Spider development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: spider-cpu: Add GP LEDs
arm64: dts: renesas: r8a779f0: Add INTC-EX node
arm64: dts: renesas: rzg2ul-smarc: Add support for enabling MTU3
arm64: dts: renesas: r9a07g043: Add MTU3a node
ARM dts: renesas: armadillo800eva: Switch to enable-gpios
arm64: dts: renesas: rzg2lc-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: rzg2lc-smarc-som: Add PHY interrupt support for ETH0
riscv: dts: renesas: Clean up dtbs_check W=1 warning due to empty phy node
arm64: dts: renesas: rzg2lc-smarc: Add support for enabling MTU3
arm64: dts: renesas: rzg2l-smarc: Add support for enabling MTU3
arm64: dts: renesas: Add missing space before {
ARM: dts: renesas: Add missing space before {
arm64: dts: renesas: Minor whitespace cleanup around '='
arm64: dts: renesas: rzg2l-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: r9a09g011: Add CSI nodes
arm64: dts: renesas: rzg2l: Fix txdv-skew-psec typos
arm64: dts: renesas: rzg2l: Update overfow/underflow IRQ names for MTU3 channels
Arnd Bergmann [Sat, 12 Aug 2023 08:39:04 +0000 (10:39 +0200)]
Merge tag 'tegra-for-6.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
arm64: tegra: Device tree changes for v6.6-rc1
The majority of this is fixes all over the place for DT schema
validation warnings. However, there are also cleanups for some things in
DT and audio support is added on IGX Orin. Jetson Orin NX and Nano also
gain a new thermal trip point to help keep the device cool at moderate
loads.
* tag 'tegra-for-6.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (22 commits)
arm64: tegra: Add blank lines for better readability
arm64: tegra: Remove {clock,reset}-names from VIC powergate
arm64: tegra: Drop incorrect maxim,disable-etr on Smaug
arm64: tegra: Add SPI device tree nodes for Tegra234
arm64: tegra: Enable UARTA and UARTE for Orin Nano
arm64: tegra: Add UARTE device tree node on Tegra234
arm64: tegra: Adapt to LP855X bindings changes
arm64: tegra: Add PCIe and DP 3.3V supplies
arm64: tegra: Add missing reset-names for Tegra HS UART
arm64: tegra: Remove current-speed for SBSA UART
arm64: tegra: smaug: Remove reg-shift for high-speed UART
arm64: tegra: Remove dmas and dma-names for debug UART
arm64: tegra: Add 35°C trip point for Jetson Orin NX/Nano
arm64: tegra: Remove duplicate PCI nodes
arm64: tegra: Sort PCI nodes correctly on Orin
arm64: tegra: Add audio support for IGX Orin
arm64: tegra: Update CPU OPP tables
arm64: tegra: Fix HSUART for Smaug
arm64: tegra: Fix HSUART for Jetson AGX Orin
arm64: tegra: Add missing alias for NVIDIA IGX Orin
...
Arnd Bergmann [Sat, 12 Aug 2023 08:38:27 +0000 (10:38 +0200)]
Merge tag 'tegra-for-6.6-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
ARM: tegra: Device tree changes for v6.6-rc1
This contains various fixes for DT schema validation and the Pegatron
Chagall and Nexus 7 get specific compatible strings for the panels that
they use.
* tag 'tegra-for-6.6-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Provide specific compatible string for Nexus 7 panel
ARM: tegra: Use Hannstar HSD101PWW2 on Pegatron Chagall
ARM: tegra: Reuse I2C3 for NVEC
ARM: tegra: Add missing reset-names for Tegra HS UART
ARM: tegra: Remove reset-names for UART devices
ARM: tegra: Remove dmas and dma-names for debug UART
Guido Günther [Thu, 10 Aug 2023 17:59:51 +0000 (19:59 +0200)]
arm64: dts: imx8mq-librem5-devkit: Drop power-supply
It's not a valid binding. Instead move the sdio_rst line to the power
sequence and use w_disable1 as the vmmc-supply bringing it more in line
with other SDIO M2 cards.
Resolves following warning:
arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dtb: mmc@30b50000: Unevaluated properties are not allowed ('power-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/mmc/fsl-imx-esdhc.yaml#
Numbers are separated by dashes. Fixes the warnings:
arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dtb: gpio-buttons: 'button1',
'button2', 'button3' do not match any of the regexes:
'^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alexander Stein [Thu, 10 Aug 2023 09:55:41 +0000 (11:55 +0200)]
ARM: dts: imx6ul: Fix nand-controller #size-cells
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dtb:
nand-controller@1806000: #size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bryan Brattlof [Fri, 11 Aug 2023 18:44:31 +0000 (00:14 +0530)]
arm64: dts: ti: Introduce AM62P5 family of SoCs
The AM62Px is an extension of the existing Sitara AM62x low-cost family
of application processors built for Automotive and Linux Application
development. Scalable Arm Cortex-A53 performance and embedded features,
such as: multi high-definition display support, 3D-graphics
acceleration, 4K video acceleration, and extensive peripherals make the
AM62Px well-suited for a broad range of automation and industrial
application, including automotive digital instrumentation, automotive
displays, industrial HMI, and more.
Some highlights of AM62P SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Dual/Single core variants are provided in the same package to allow HW
compatible designs.
* One Device manager Cortext-R5F for system power and resource
management, and one Cortex-R5F for Functional Safety or
general-purpose usage.
* One 3D GPU up to 50 GLFOPS
* H.264/H.265 Video Encode/Decode.
* Display support: 3x display support over OLDI/LVDS (1x OLDI-DL, 1x or
2x OLDI-SL), DSI, or DPI. Up to 3840x1080@60fps resolution
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1xCSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized Hardware Security Module with support for secure
boot, debug security and crypto acceleration and trusted execution
environment.
* One 32-bit DDR Subsystem that supports LPDDR4, DDR4 memory types.
* Multiple low power modes support, ex: Deep sleep, Standby, MCU-only,
enabling battery powered system design.
For those interested, more details about this SoC can be found in the
Technical Reference Manual here:
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
wkup_i2c0, mcu_uart0, main_uart8, main_sdhci0 and main_sdhci1 are required
for bootloader operation on TI K3 AM69-SK EVM. These IPs along with
pinmuxes need to be marked for all bootloader phases, hence add bootph-all
to these nodes in kernel dts.
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
wkup_i2c0, mcu_uart0, main_uart8, fss, ospi0, ospi1, main_sdhci0 and
main_sdhci1 are required for bootloader operation on TI K3 J784S4 EVM.
These IPs along with pinmuxes need to be marked for all bootloader phases,
hence add bootph-all to these nodes in kernel dts.
Apurva Nandan [Fri, 11 Aug 2023 19:20:28 +0000 (00:50 +0530)]
arm64: dts: ti: k3-j784s4: Add phase tags marking
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to cover U-Boot challenges with DT.
That's why add it also to Linux to be aligned with bootloader requirement.
On TI K3 J784S4 SoC, only secure_proxy_mcu and secure_proxy_sa3 nodes are
exclusively used by R5 bootloader, rest of the dts nodes with bootph-* are
used by later boot stages also.
And secure_proxy_mcu and secure_proxy_sa3 are disabled in kernel device
tree, and will be only enabled in R5 bootloader device tree.
So, bootph-pre-ram for secure_proxy_mcu and secure_proxy_sa3 will be
added in R5 bootloader device tree only.
Add bootph-all for all other nodes that are used in the bootloader on
K3 J784S4 SoC, and bootph-pre-ram is not needed specifically for any node
in kernel dts.
Nishanth Menon [Wed, 9 Aug 2023 08:45:58 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am625-beagleplay: Add HDMI support
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (ITE-IT66121) on the BeaglePlay platform. For audio output,
BeaglePlay uses mcasp1.
Add pinmux info for DSS DPI signals.
Further, add support for HDMI audio and video output.
Aradhya Bhatia [Wed, 9 Aug 2023 08:45:56 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am62x-sk-common: Add HDMI support
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux info for DSS DPI output.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM625 SK and AM62-LP SK platforms.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Aradhya Bhatia [Wed, 9 Aug 2023 08:45:55 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am62-main: Add node for DSS
Add Display SubSystem (DSS) DT node for the AM625 SoC.
The DSS supports one each of video pipeline (vid) and video-lite
pipeline (vidl1). It outputs OLDI signals on one video port (VP1) and
DPI signals on another (VP2). The video ports are connected to the
pipelines via 2 identical overlay managers (ovr1 and ovr2).
Also add the DT node for DSS clock divider. This is a fixed-factor-clock
and does not have any register. This comes into effect whenenver OLDI
display is used. The input to this divider is a serial clock used by
OLDI TXes. The divider divides the input clock by 7, and provides the
pixel clock to VP1.
Aradhya Bhatia [Wed, 9 Aug 2023 08:45:54 +0000 (14:15 +0530)]
arm64: dts: ti: k3-am62x-sk-common: Update main-i2c1 frequency
The Display Data Channel (DDC) transactions between an HDMI transmitter
(SIL9022A in this case) and an HDMI monitor, occur at a maximum of
100KHz. That's the maximum supported frequency within DDC standards.
While the SIL9022A can transact with the core at 400KHz, it needs to
drop the frequency to 100KHz when communicating with the monitor,
otherwise, the i2c controller times out and shows warning like this.
[ 985.773431] omap_i2c 20010000.i2c: controller timed out
That feature, however, has not been enabled in the SIL9022 driver.
Since, dropping the frequency doesn't affect any other devices on the
bus, drop the main-i2c1 frequency from 400KHz to 100KHz.
Fabio Estevam [Wed, 9 Aug 2023 11:36:58 +0000 (08:36 -0300)]
arm64: dts: imx8m-beacon-kit: Remove extra sound-sai entry
'sound-dai' should contain only 'sai5'. Remove the extra entry to
fix the following schema warning:
imx8mm-beacon-kit.dtb: sound-hdmi: simple-audio-card,cpu:sound-dai: [[110], [0]] is too long
from schema $id: http://devicetree.org/schemas/sound/simple-card.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de> Acked-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Wed, 9 Aug 2023 07:10:25 +0000 (09:10 +0200)]
dt-bindings: arm: Add Polyhex DEBIX SOM A based boards
Add devicetree bindings for i.MX8MP based DEBIX SOM A and SOM A I/O
baseboard:
- https://debix.io/hardware/debix-som-a.html
- https://debix.io/hardware/debix-som-a-io-board.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Wed, 9 Aug 2023 07:10:24 +0000 (09:10 +0200)]
dt-bindings: arm: fsl: fix DEBIX binding
The current imx8mp-debix-model-a.dts uses all three compatibles. Fix the
corresponding bindings by adding an own entry for it. Adapt the comment
for the "polyhex,imx8mp-debix" binding to make it clear that this should
only be used for DEBIX Model A/B i.MX8MP SBCs.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marco Felsch [Wed, 9 Aug 2023 07:10:26 +0000 (09:10 +0200)]
arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
Add support for the Debix SOM A + SOM A I/O board. The commit enables
only the basic features like:
- 2x UART
- 2x Network
- eMMC/µSD
- CAN
- QSPI
- USB Host / Device
The SoM A uses the EQOS ethernet interface and not the FEC, so drop the
interface pinctrl node from the device tree.
Fixes: c86d350aae68 ("arm64: dts: Add device tree for the Debix Model A Board") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass "brcm,bcm4329-fmac" to fix the following schema warnings:
imx8mp-venice-gw74xx.dtb: wifi@0: compatible: 'oneOf' conditional failed, one must be fixed:
['cypress,cyw4373-fmac'] is too short
'cypress,cyw4373-fmac' is not one of ['brcm,bcm4329-fmac', 'pci14e4,43dc', 'pci14e4,4464', 'pci14e4,4488', 'pci14e4,4425', 'pci14e4,4433']
from schema $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml#
imx8mn-venice-gw7902.dtb: wifi@0: compatible: 'oneOf' conditional failed, one must be fixed:
['brcm,bcm43455-fmac'] is too short
'brcm,bcm43455-fmac' is not one of ['brcm,bcm4329-fmac', 'pci14e4,43dc', 'pci14e4,4464', 'pci14e4,4488', 'pci14e4,4425', 'pci14e4,4433']
from schema $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml#
Andrew Davis [Wed, 9 Aug 2023 18:01:45 +0000 (13:01 -0500)]
arm64: dts: ti: k3-j721e: Enable C6x DSP nodes at the board level
C6x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C6x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Andrew Davis [Wed, 9 Aug 2023 18:01:44 +0000 (13:01 -0500)]
arm64: dts: ti: k3-j784s4: Enable C7x DSP nodes at the board level
C7x DSP nodes defined in the top-level J784s4 SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C7x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Andrew Davis [Wed, 9 Aug 2023 18:01:43 +0000 (13:01 -0500)]
arm64: dts: ti: k3-j721e: Enable C7x DSP nodes at the board level
C7x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C7x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Patrice Chotard [Tue, 8 Aug 2023 09:31:19 +0000 (11:31 +0200)]
ARM: dts: st: Add gpio-ranges for stm32f769-pinctrl
Since commit 913a956c4363 ("pinctrl: stm32: use dynamic allocation
of GPIO base"), it's impossible to retrieve gpios from phandle,
for example, mmc driver can't retrieve cd-gpios.
Add missing gpio-ranges properties to fix it.
Patrice Chotard [Tue, 8 Aug 2023 09:31:18 +0000 (11:31 +0200)]
ARM: dts: st: Add gpio-ranges for stm32f746-pinctrl
Since commit 913a956c4363 ("pinctrl: stm32: use dynamic allocation
of GPIO base"), it's impossible to retrieve gpios from phandle,
for example, mmc driver can't retrieve cd-gpios.
Add missing gpio-ranges properties to fix it.
projects / users / jedix / linux-maple.git / log