Christian Lamparter [Fri, 24 Dec 2021 13:44:08 +0000 (14:44 +0100)]
apm821xx: fix WD MyBook Live DUO USB-Port
where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:
dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up
One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")
|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]
the same method proposed there worked with APM821xx's USB IP-Core.
Hauke Mehrtens [Sun, 5 Dec 2021 20:58:31 +0000 (21:58 +0100)]
mac80211: Update toversion 5.10.85
The following patches were backported from upstream before and are not
needed any more:
package/kernel/mac80211/patches/ath/980-ath10k-fix-max-antenna-gain-unit.patch
package/kernel/mac80211/patches/subsys/307-mac80211-do-not-access-the-IV-when-it-was-stripped.patch
Rafał Miłecki [Wed, 3 Nov 2021 17:12:05 +0000 (18:12 +0100)]
bcm4908: start work on images for devices using U-Boot
New BCM4908 family based routers will use U-Boot bootloader. That will
require using a totally different firmware format. Kernel has to be put
in a FIT image.
OpenWrt has some helpers for generating .its files but they don't fit
BCM4908 requirements and there is no simple way of extending any of
them. The best solution seems to be storing an .its template.
BCM4908 bootfs may:
1. contain extra binaries (other than kernel & DTB)
2. include multiple DTB files
3. store device specific U-Boot configurations with custom properties
Such setups are too complex to generate using shell script. Raw .its
file on the other hand seems quire clean & reasonable.
Rafał Miłecki [Sun, 28 Nov 2021 10:54:19 +0000 (11:54 +0100)]
bcm53xx: sysupgrade: refactor handling different firmware formats
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.
Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.
This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s
The following patch does not apply to upstream any more and needs some
more work to make it work fully again. I am not sure if we are still
able to set the UART to a none standard baud rate.
target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch
These patches needed manually changes:
target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch
target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch
target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch
target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
All others updated automatically.
Compile-tested on: malta/le, armvirt/64, lantiq/xrx200
Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200
MAC addresses map (like in OEM firmware)
art@0x0 88:C3:97:*:57 wan/label
art@0x1002 88:C3:97:*:2D lan/wlan2g
art@0x5006 88:C3:97:*:2C wlan5g
Obtain SSH Access
1. Download and flash the firmware version 1.3.8 (China).
2. Login to the router web interface and get the value of `stok=` from the
URL
3. Open a new tab and go to the following URL (replace <STOK> with the stok
value gained above; line breaks are only for easier handling, please put
together all four lines into a single URL without any spaces):
http://192.168.31.1/cgi-bin/luci/;stok=<STOK>/api/misystem/set_config_iotdev
?bssid=any&user_id=any&ssid=-h%0Anvram%20set%20ssh_en%3D1%0Anvram%20commit
%0Ased%20-i%20%27s%2Fchannel%3D.%2A%2Fchannel%3D%5C%5C%22debug%5C%5C%22%2F
g%27%20%2Fetc%2Finit.d%2Fdropbear%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A
4. Wait 30-60 seconds (this is the time required to generate keys for the
SSH server on the router).
Create Full Backup
1. Obtain SSH Access.
2. Create backup of all flash (on router):
dd if=/dev/mtd0 of=/tmp/ALL.backup
3. Copy backup to PC (on PC):
scp root@192.168.31.1:/tmp/ALL.backup ./
Tip: backup of the original firmware, taken three times, increases the
chances of recovery :)
Calculate The Password
* Locally using shell (replace "12345/E0QM98765" with your router's serial
number):
On Linux
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5sum - | head -c8 && echo
On macOS
printf "%s6d2df50a-250f-4a30-a5e6-d44fb0960aa0" "12345/E0QM98765" | \
md5 | head -c8
* Locally using python script (replace "12345/E0QM98765" with your
router's serial number):
wget https://raw.githubusercontent.com/eisaev/ax3600-files/master/scripts/calc_passwd.py
python3.7 -c 'from calc_passwd import calc_passwd; print(calc_passwd("12345/E0QM98765"))'
* Online
https://www.oxygen7.cn/miwifi/
Debricking (lite)
If you have a healthy bootloader, you can use recovery via TFTP using
programs like TinyPXE on Windows or dnsmasq on Linux. To switch the router
to TFTP recovery mode, hold down the reset button, connect the power
supply, and release the button after about 10 seconds. The router must be
connected directly to the PC via the LAN port.
Debricking
You will need a full dump of your flash, a CH341 programmer, and a clip
for in-circuit programming.
Install OpenWRT
1. Obtain SSH Access.
2. Create script (on router):
echo '#!/bin/sh' > /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo '. /bin/boardupgrade.sh' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
echo 'board_prepare_upgrade' >> /tmp/flash_fw.sh
echo 'mtd erase rootfs_data' >> /tmp/flash_fw.sh
echo 'mtd write /tmp/openwrt.bin firmware' >> /tmp/flash_fw.sh
echo 'sleep 3' >> /tmp/flash_fw.sh
echo 'reboot' >> /tmp/flash_fw.sh
echo >> /tmp/flash_fw.sh
chmod +x /tmp/flash_fw.sh
3. Copy `openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin`
to the router (on PC):
scp openwrt-ath79-generic-xiaomi_aiot-ac2350-squashfs-sysupgrade.bin \
root@192.168.31.1:/tmp/openwrt.bin
4. Flash OpenWRT (on router):
/bin/ash /tmp/flash_fw.sh &
5. SSH connection will be interrupted - this is normal.
6. Wait for the indicator to turn blue.
Signed-off-by: Evgeniy Isaev <isaev.evgeniy@gmail.com>
[improve commit message formatting slightly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6c148116f778bfd2db88476cee4753b32538eafe)
Sergey V. Lobanov [Fri, 26 Nov 2021 17:26:17 +0000 (20:26 +0300)]
ramips: fix tl-mr3020-v3 switch topology to configure vlans via luci
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e22c91e144d63ccbd7b76b370a53652c48db1d6f)
Felix Fietkau [Fri, 3 Dec 2021 09:56:17 +0000 (10:56 +0100)]
mt76: update to the latest version
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips 9a8fc6636d83 mt76: move sar_capa configuration in common code 7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr 678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Felix Fietkau [Thu, 2 Dec 2021 10:26:36 +0000 (11:26 +0100)]
mt76: update to the latest version
a6451fea5a3d mt76: mt7615: improve wmm index allocation 1911486414dc mt76: mt7915: improve wmm index allocation 7998a41d1321 mt76: clear sta powersave flag after notifying driver 664475574438 mt76: mt7603: introduce SAR support 5c0da39c940b mt76: mt7915: introduce SAR support 77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering 094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623 25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips 1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning 586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init 8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege 688e30c7d854 firmware: update mt7921 firmware to version 20211014 6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi 95acf972750c mt76: fix 802.3 RX fail by hdr_trans 3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count 929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Mathias Kresin [Sat, 27 Nov 2021 16:28:19 +0000 (17:28 +0100)]
lantiq: set maximum kernel size for P2812HNUF3
The board has a fixed size kernel partition but do not limit the kernel
size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Felix Fietkau [Wed, 24 Nov 2021 16:02:26 +0000 (17:02 +0100)]
hostapd: add a patch that allows processing auth requests for peers in blocked state
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Felix Fietkau [Wed, 24 Nov 2021 09:45:28 +0000 (10:45 +0100)]
mac80211: fix regression in SSN handling of addba tx
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
David Bauer [Tue, 23 Nov 2021 21:25:02 +0000 (22:25 +0100)]
hostapd: fix goto loop for ubus assoc handler
When a ubus event handler denies a association with a non-zero return
value, the code jumps to preceeding code, creating an endless loop until
the event handler accepts the assc request.
Move the ubus handler further up the code to avoid creating such a loop.
Felix Fietkau [Wed, 3 Nov 2021 21:40:53 +0000 (22:40 +0100)]
hostapd: add wmm qos map set by default
This implements the mapping recommendations from RFC8325, with an
update from RFC8622. This ensures that DSCP marked packets are properly
sorted into WMM classes.
The map can be disabled by setting iw_qos_map_set to something invalid
like 'none'
Felix Fietkau [Wed, 20 Oct 2021 19:13:10 +0000 (21:13 +0200)]
hostapd: fix a race condition on adding AP mode wds sta interfaces
Both hostapd and netifd attempt to add a VLAN device to a bridge.
Depending on which one wins the race, bridge vlan settings might be incomplete,
or hostapd might run into an error and refuse to service the client.
Fix this by preventing hostapd from adding interfaces to the bridge and
instead rely entirely on netifd handling this properly
When using htmode 'HE20' with a radio mode that uses wpa-supplicant
(like mesh or sta), it will default to 40 MHz bw if disable_ht40 is not
set. This commit fixes this behaviour.
Felix Fietkau [Fri, 4 Jun 2021 07:12:07 +0000 (09:12 +0200)]
hostapd: configure inter-AP communication interface for 802.11r
In setups using VLAN bridge filtering, hostapd may need to communicate using
a VLAN interface on top of the bridge, instead of using the bridge directly
Rui Salvaterra [Wed, 25 Nov 2020 23:03:48 +0000 (23:03 +0000)]
hostapd: enable airtime policy for the -basic variants
Airtime policy configuration is extremely useful in multiple BSS scenarios.
Since nowadays most people configure both private and guest networks (at
least), it makes sense to enable it by default, except for the most limited
of the variants.
Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2):
543944 bytes (airtime policy disabled)
548040 bytes (airtime policy enabled)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry-picked from commit d38f4565828264731f2a9cfe646491fba80315d3)
Felix Fietkau [Wed, 2 Jun 2021 05:45:31 +0000 (07:45 +0200)]
mac80211: do not enable VHT in the default config on 2.4 GHz
Some drivers advertise it, but it's not supported at the moment
Reported-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 42a99b18ff23fa768a6ae5f1076f15cbfa494f24)
Felix Fietkau [Wed, 2 Jun 2021 05:42:40 +0000 (07:42 +0200)]
mac80211: fix detecting VHT capabilities when generating the default config
The colon does not directly follow the "VHT Capabilities" string
Reported-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 3518b793a2f2293e7e9124b5beae7b09887c5e32)
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
Christian Lamparter [Sat, 23 Oct 2021 16:08:51 +0000 (18:08 +0200)]
wireless-regdb: update to version 2021.08.28
e983a25 Update regulatory rules for Ecuador (EC) a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz 86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US 6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US 9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately 42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB
Deomid Ryabkov [Sat, 23 Oct 2021 13:22:39 +0000 (16:22 +0300)]
base-files: chmod 1777 /var/lock
Per FHS 3.0, /var/lock is the location for lock files [1].
However its current permissions (755) are too restrictive
for use by unprivileged processes.
Debian and Ubuntu set them to 1777, and now so do we.
Signed-off-by: Deomid Ryabkov <rojer@rojer.me>
[fixed typo in commit message, had to remove "rojer" due to git hooks] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 430f69194388ad6a7826a51e0e2b2dd478e27f0f)
Stephan Schmidtmer [Tue, 10 Aug 2021 20:21:30 +0000 (20:21 +0000)]
libpcap: add rpcapd as package
This enables building of rpcapd and adds it as a package.
It is a daemon that allows remote packet capturing from another machine.
E.g. Wireshark can talk to it using the Remote Capture Protocol (RPCAP).
https://www.tcpdump.org/manpages/rpcapd.8.html
Compile and run tested:
OpenWrt 21.02.0-rc4 r16256-2d5ee43dc6 on x86/64 and mvebu/cortexa9
Christian Lamparter [Thu, 5 Aug 2021 13:29:25 +0000 (15:29 +0200)]
gpio-button-hotplug: convert to gpio descriptor (gpiod_) API
OpenWrt's special gpio-button-hotplug driver is still using
exclusively the legacy GPIO Subsystem gpio_ API.
While it still does work fine for most devices, upstream
linux is starting to convert platform support like that of
the APU2/3/4 to the new GPIOD LOOKUP tables that are not
supported by it.
Hence, this patch replaces the gpio_ calls present in
gpio-button-hotplug with gpiod_ equivalent wherever
it's possible. This allows the driver to use the
gpiod lookup tables and still have a fallback for
legacy platform data code that just sets button->gpio
set to the real button/switch GPIO.
As a bonus: the active_low logic is now being handled
by the linux's gpio subsystem too. Another issue that
was address is the of_handle leak in the dt parser
error path.
Bruno Randolf [Mon, 25 Oct 2021 10:38:15 +0000 (11:38 +0100)]
ramips: minew g1-c: Allow dynamic RAM sizes
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.
Roman Yeryomin [Fri, 3 Sep 2021 14:31:11 +0000 (17:31 +0300)]
iproute2: m_xt.so depends on dynsyms.list
When doing parallel build on a fast machine with bottleneck in i/o,
m_xt.so may start linking faster than dynsyms.list gets populated,
resulting in error:
ld:dynsyms.list:0: syntax error in dynamic list
Fix this by adding dynsyms.list as make dependency to m_xt.so
Described also here:
https://bugs.openwrt.org/index.php?do=details&task_id=3353
Change from v1:
- add dynsysms.list dependancy only when shared libs are enabled
projects / users / dwmw2 / openwrt.git / log