The iTXQs stop/wake queue mechanism involves a whole bunch
of locks and this is probably why the call to
ieee80211_wake_txqs is deferred to a tasklet when called from
__ieee80211_wake_queue.
Another advantage of that is that ieee80211_wake_txqs might
call the wake_tx_queue() callback and then the driver may
call mac80211 which will call it back in the same context.
The bug I saw is that when we send a deauth frame as a
station we do:
flush(drop=1)
tx deauth
flush(drop=0)
While we flush we stop the queues and wake them up
immediately after we finished flushing. The problem here is
that the tasklet that de-facto enables the queue may not have
run until we send the deauth. Then the deauth frame is sent
to the driver (which is surprising by itself), but the driver
won't get anything useful from ieee80211_tx_dequeue because
the queue is stopped (or more precisely because
vif->txqs_stopped[0] is true).
Then the deauth is not sent. Later on, the tasklet will run,
but that'll be too late. We'll already have removed all the
vif etc...
Fix this by calling ieee80211_wake_txqs synchronously if we
are not waking up the queues from the driver (we check the
reason to determine that). This makes the code really
convoluted because we may call ieee80211_wake_txqs from
__ieee80211_wake_queue. The latter assumes that
queue_stop_reason_lock has been taken by the caller and
ieee80211_wake_txqs may release the lock to send the frames.
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
tk_core.seq is initialized open coded, but that misses to initialize the
lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq
consequently lack a name and are hard to read.
Use the proper initializer which takes care of the lockdep map
initialization.
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.
Fixes: 03ea6d6e9e1ff1 ("usb: dwc2: Enable power down") Acked-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Spreadtrum DMA link-list mode is always one cyclic transfer,
so we should clear the SPRD_DMA_LLIST_END flag for the link-list
configuration. Moreover add cyclic callback support for the cyclic
transfer.
Signed-off-by: Eric Long <eric.long@spreadtrum.com> Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Rename SPI controller node in the XTFPGA DTS to spi@...
This fixes the following build warnings:
arch/xtensa/boot/dts/kc705_nommu.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/kc705_nommu.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/lx200mx.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/lx200mx.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/kc705.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/kc705.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/ml605.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/ml605.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
arch/xtensa/boot/dts/lx60.dtb: Warning (spi_bus_bridge):
/soc/spi-master@0d0a0000: node name for SPI buses should be 'spi'
arch/xtensa/boot/dts/lx60.dtb: Warning (spi_bus_reg):
Failed prerequisite 'spi_bus_bridge'
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function smack_key_permission() only issues smack requests for the
following operations:
- KEY_NEED_READ (issues MAY_READ)
- KEY_NEED_WRITE (issues MAY_WRITE)
- KEY_NEED_LINK (issues MAY_WRITE)
- KEY_NEED_SETATTR (issues MAY_WRITE)
A blank smack request is issued in all other cases, resulting in
smack access being granted if there is any rule defined between
subject and object, or denied with -EACCES otherwise.
Request MAY_READ access for KEY_NEED_SEARCH and KEY_NEED_VIEW.
Fix the logic in the unlikely case when both MAY_READ and
MAY_WRITE are needed. Validate access permission field for valid
contents.
We lose even config space access when we power gate the ISP
via the PUNIT. That makes lspci & co. produce gibberish.
To fix that let's try to implement actual runtime pm hooks
and inform the pci core that the device always goes to
D3cold. That will cause the pci core to resume the device
before attempting config space access.
This introduces another annoyance though. We get the
following error every time we try to resume the device:
intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
The reason being that the pci core tries to put the device
back into D0 via the standard PCI PM mechanism before
calling the driver resume hook. To fix this properly
we'd need to infiltrate the platform pm hooks (could
turn ugly real fast), or use pm domains (which don't
seem to exist on x86), or some extra early resume
hook for the driver (which doesn't exist either).
So maybe we just choose to live with the error?
Cc: Hans de Goede <hdegoede@redhat.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Darren Hart <dvhart@infradead.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without CONFIG_HDMI, we get a link error for this driver:
drivers/media/i2c/tda1997x.o: In function `tda1997x_parse_infoframe':
tda1997x.c:(.text+0x2195): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text+0x21b6): undefined reference to `hdmi_infoframe_log'
drivers/media/i2c/tda1997x.o: In function `tda1997x_log_infoframe':
tda1997x.c:(.text.unlikely+0x13d3): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text.unlikely+0x1426): undefined reference to `hdmi_infoframe_log'
All other drivers in this directory that use HDMI select CONFIG_HDMI,
so do the same here:
Fix build errors when CONFIG_PINCTRL is not enabled.
The header file <linux/pinctrl/consumer.h> handles both CONFIG_PINCTRL
enabled and disabled cases.
CC [M] drivers/spi/spi-at91-usart.o
../drivers/spi/spi-at91-usart.c: In function 'at91_usart_spi_runtime_suspend':
../drivers/spi/spi-at91-usart.c:409:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_sleep_state(dev);
../drivers/spi/spi-at91-usart.c: In function 'at91_usart_spi_runtime_resume':
../drivers/spi/spi-at91-usart.c:419:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_default_state(dev);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Radu Pirea <radu.pirea@microchip.com> Cc: Mark Brown <broonie@kernel.org> Cc: linux-spi@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The base aspeed-g5.dtsi already defines a '/memory@80000000' node, so
'/memory' in the board files create a duplicate node. We're probably
getting lucky that the bootloader fixes up the memory node that the
kernel ends up using. Add the unit-address so it's merged with the base
node.
Found with DT json-schema checks.
Cc: Joel Stanley <joel@jms.id.au> Cc: Andrew Jeffery <andrew@aj.id.au> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-aspeed@lists.ozlabs.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:
arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58
I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.
I'm also copying some properties from TWSI1 that were missing or
incorrect.
Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Tested-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
v3d_bo_get_pages() checks this to decide to map the imported buffer
instead of the backing shmem file. The caller was about to set this
value anyway, and there's no error path in between. Ideally we
wouldn't even allocate the shmem file for our imports, but that's a
more invasive fix.
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 57692c94dcbe ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+") Link: https://patchwork.freedesktop.org/patch/msgid/20181128230927.10951-3-eric@anholt.net Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Dave Emett <david.emett@broadcom.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The core ftrace code requires that when it is handed the PC of an
instrumented function, this PC is the address of the instrumented
instruction. This is necessary so that the core ftrace code can identify
the specific instrumentation site. Since the instrumented function will
be a BL, the address of the instrumented function is LR - 4 at entry to
the ftrace code.
This fixup is applied in the mcount_get_pc and mcount_get_pc0 helpers,
which acquire the PC of the instrumented function.
The mcount_get_lr helper is used to acquire the LR of the instrumented
function, whose value does not require this adjustment, and cannot be
adjusted to anything meaningful. No adjustment of this value is made on
other architectures, including arm. However, arm64 adjusts this value by
4.
This patch brings arm64 in line with other architectures and removes the
adjustment of the LR value.
Fix IBI_R11 configuration on non-radar channels for mt76x0e
driver. This patch improve system stability under heavy load.
Moreover use IBI_R11 name and remove magic numbers for
0x212c register
Fixes: 0c3b3abc9251 ("mt76x0: pci: add DFS support") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
There exist very few ap messages which need to have the 'special' flag
enabled. This flag tells the firmware layer to do some pre- and maybe
postprocessing. However, it may happen that this special flag is
enabled but the firmware is unable to deal with this kind of message
and thus returns with reply code 0x41. For example older firmware may
not know the newest messages triggered by the zcrypt device driver and
thus react with reject and the named reply code. Unfortunately this
reply code is not known to the zcrypt error routines and thus default
behavior is to switch the ap queue offline.
This patch now makes the ap error routine aware of the reply code and
so userspace is informed about the bad processing result but the queue
is not switched to offline state any more.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ce2e6db554fa ("brcmfmac: Add support for getting nvram contents from EFI variables")
we have a device driver accessing the efivars API. Several functions in
the efivars API assume __efivars is set, i.e., that they will be accessed
only after efivars_register() has been called. However, the following NULL
pointer access was reported calling efivar_entry_size() from the brcmfmac
device driver:
Disassembly showed that the local static variable __efivars is NULL,
which is not entirely unexpected given that it is a non-EFI platform.
So add a NULL pointer check to efivar_entry_size(), and to related
functions while at it. In efivars_register() a couple of sanity checks
are added as well.
Reported-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bhupesh Sharma <bhsharma@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Eric Snowberg <eric.snowberg@oracle.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Joe Perches <joe@perches.com> Cc: Julien Thierry <julien.thierry@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Cc: Sedat Dilek <sedat.dilek@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: YiFei Zhu <zhuyifei1999@gmail.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20181129171230.18699-9-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sysfs interface to update cooling device cur_state does not
currently holding cooling device lock sometimes leading to
stale values in cur_state if getting updated simultanelously
from user space and thermal framework. Adding the proper locking
code fixes this issue.
commit ff140fea847e ("Thermal: handle thermal zone device properly
during system sleep") added PM hook to call thermal zone reset during
sleep. However resetting thermal zone will also clear the passive state
and thus cancel the polling queue which leads the passive cooling device
state not being cleared properly after sleep.
thermal_pm_notify => thermal_zone_device_reset set passive to 0
thermal_zone_trip_update will skip update passive as `old_target ==
instance->target'.
monitor_thermal_zone => thermal_zone_device_set_polling will cancel
tz->poll_queue, so the cooling device state will not be changed
afterwards.
Reported-by: Kame Wang <kamewang@google.com> Signed-off-by: Wei Wang <wvw@google.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As of commit 6460d3201471 ("arm64: io: Ensure calls to delay routines
are ordered against prior readX()"), MMIO reads smaller than 64 bits
fail to compile under clang because we end up mixing 32-bit and 64-bit
register operands for the same data processing instruction:
./include/asm-generic/io.h:695:9: warning: value size does not match register size specified by the constraint and modifier [-Wasm-operand-widths]
return readb(addr);
^
./arch/arm64/include/asm/io.h:147:58: note: expanded from macro 'readb'
^
./include/asm-generic/io.h:695:9: note: use constraint modifier "w"
./arch/arm64/include/asm/io.h:147:50: note: expanded from macro 'readb'
^
./arch/arm64/include/asm/io.h:118:24: note: expanded from macro '__iormb'
asm volatile("eor %0, %1, %1\n" \
^
Fix the build by casting the macro argument to 'unsigned long' when used
as an input to the inline asm.
Reported-by: Nick Desaulniers <nick.desaulniers@gmail.com> Reported-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kasprintf() may return NULL on failure of internal allocation
thus the assignment to 'name' is not safe if unchecked. If NULL
is passed in for name then perf_pmu_register() would not fail
but rather silently jump to skip_type which is not the intent
here. As perf_pmu_register() may also return -ENOMEM returning
-ENOMEM in the (unlikely) failure case of devm_kasprintf() should
be fine here as well.
Acked-by: Mark Rutland <mark.rutland@arm.com> Fixes: d5d9696b0380 ("drivers/perf: Add support for ARMv8.2 Statistical Profiling Extension") Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[will: reworded error message] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drm_atomic_helper_commit_duplicated_state() sets state->acquire_ctx to
the context given in the argument and leaves it in state after it
quits. The lifetime of state and context are not guaranteed to be the
same, so we shouldn't leave that pointer hanging around. This patch
resets the context to NULL to avoid any oopses.
1) Checkout fresh master Linux branch (tested with commit e195ca6cb)
2) Copy x84_64-config-4.14 to .config, then enable NFS server v4 and build
3) From `kvm-xfstests shell`:
results in NULL dereference in locks_end_grace.
Check that nfsd has been started before trying to end the grace period.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_brcmstb()
doesn't do that, so fix it.
[treding: slightly rewrite to avoid inline comparison]
Fixes: d52fad262041 ("soc: add stubs for brcmstb SoC's") Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:260:7:
warning: variable 'err' set but not used [-Wunused-but-set-variable]
'err' should be returned while set MPI_DEINIT state fails
in hw_atl_utils_soft_reset.
Fixes: cce96d1883da ("net: aquantia: Regression on reset with 1.x firmware") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A relatively standard idiom for ensuring that a pair of MMIO writes to a
device arrive at that device with a specified minimum delay between them
is as follows:
the intention being that the read-back from the device will push the
prior write to CTL1, and the udelay will hold up the write to CTL1 until
at least 10us have elapsed.
Unfortunately, on arm64 where the underlying delay loop is implemented
as a read of the architected counter, the CPU does not guarantee
ordering from the readl() to the delay loop and therefore the delay loop
could in theory be speculated and not provide the desired interval
between the two writes.
Fix this in a similar manner to PowerPC by introducing a dummy control
dependency on the output of readX() which, combined with the ISB in the
read of the architected counter, guarantees that a subsequent delay loop
can not be executed until the readX() has returned its result.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for the IIC code for the r8a77990 (R-Car E3).
It is not considered compatible with existing fallback bindings
due to the documented absence of automatic transmission registers.
These registers are currently not used by the driver and
thus the provides the same behaviour for "renesas,iic-r8a77990" and
"renesas,rcar-gen3-iic". The point of declaring incompatibility is
to allow for automatic transmission register support to be added to
"renesas,iic-r8a77990" and "renesas,rcar-gen3-iic" in future.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When call f2fs_acl_create_masq() failed, the caller f2fs_acl_create()
should return -EIO instead of -ENOMEM, this patch makes it consistent
with posix_acl_create() which has been fixed in commit beaf226b863a
("posix_acl: don't ignore return value of posix_acl_create_masq()").
Fixes: 83dfe53c185e ("f2fs: fix reference leaks in f2fs_acl_create") Signed-off-by: Tiezhu Yang <kernelpatch@126.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The encrypted file may be corrupted by GC in following case:
Time 1: | segment 1 blkaddr = A | GC -> | segment 2 blkaddr = B |
Encrypted block 1 is moved from blkaddr A of segment 1 to blkaddr B of
segment 2,
Time 2: | segment 1 blkaddr = B | GC -> | segment 3 blkaddr = C |
Before page 1 is written back and if segment 2 become a victim, then
page 1 is moved from blkaddr B of segment 2 to blkaddr Cof segment 3,
during the GC process of Time 2, f2fs should wait for page 1 written back
before reading it, or move_data_block will read a garbage block from
blkaddr B since page is not written back to blkaddr B yet.
Commit 6aa58d8a ("f2fs: readahead encrypted block during GC") introduce
ra_data_block to read encrypted block, but it forgets to add
f2fs_wait_on_page_writeback to avoid racing between GC and flush.
Signed-off-by: Yunlong Song <yunlong.song@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008
accelerometers. The KIOX010A HID is for the one in the base and the
KIOX020A for the accelerometer in the keyboard.
Since userspace does not have a way yet to deal with (or ignore) the
accelerometer in the keyboard, this commit just adds the KIOX010A HID
for now so that display rotation will work.
Related: https://github.com/hadess/iio-sensor-proxy/issues/166 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch we are registering the internal clocks (for example on
Meson8b, where the SAR ADC IP block implements the divider and gate
clocks) with the following names:
- /soc/cbus@c1100000/adc@8680#adc_div
- /soc/cbus@c1100000/adc@8680#adc_en
This is bad because the common clock framework uses the clock to create
a directory in <debugfs>/clk. With such name, the directory creation
(silently) fails and the debugfs entry ends up being created at the
debugfs root.
With this change, the new clock names are:
- c1108680.adc#adc_div
- c1108680.adc#adc_en
This matches the clock naming scheme used in the PWM, Ethernet and MMC
drivers. It also fixes the problem with debugfs.
The idea is shamelessly taken from commit b96e9eb62841c5 ("pwm: meson:
Fix mux clock names").
Fixes: 3921db46a8c5bc ("iio: Convert to using %pOF instead of full_name") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_sar_adc_clk_init() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs") Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/dma/xilinx/zynqmp_dma.c:166:4: warning: attribute 'aligned' is
ignored, place it after "struct" to apply attribute to type declaration
[-Wignored-attributes]
}; __aligned(64)
^
./include/linux/compiler_types.h:200:38: note: expanded from macro
'__aligned'
^
1 warning generated.
As Nick pointed out in the previous version of this patch, the author
likely intended for this struct to be 8-byte (64-bit) aligned, not
64-byte, which is the default. Remove the hanging __aligned attribute.
drivers/ptp/ptp_clock.c:298 ptp_clock_register() warn:
passing zero to 'ERR_PTR'
'err' should be set while device_create_with_groups and
pps_register_source fails
Fixes: 85a66e550195 ("ptp: create "pins" together with the rest of attributes") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We don't want the common clock framework to disable the "cpu_clk" if
it's not used by any device. The cpufreq-dt driver does not enable the
CPU clocks. However, even if it would we would still want the CPU clock
to be enabled at all times because the CPU clock is also required even
if we disable CPU frequency scaling on a specific board.
The reason why we want the CPU clock to be enabled is a clock further up
in the tree:
Since commit 6f888e7bc7bd58 ("clk: meson: clk-pll: add enable bit") the
sys_pll can be disabled. However, since the CPU clock is derived from
sys_pll we don't want sys_pll to get disabled. The common clock
framework takes care of that for us by enabling all parent clocks of our
CPU clock when we mark the CPU clock with CLK_IS_CRITICAL.
Until now this is not a problem yet because all clocks in the CPU
clock's tree (including sys_pll) are read-only. However, once we allow
modifications to the clocks in that tree we will need this.
According to the public S805 datasheet HHI_SYS_CPU_CLK_CNTL1[29:20] is
the register for the CPU scale_div clock. This matches the code in
Amlogic's 3.10 GPL kernel sources:
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
This means that the divider register is 10 bit wide instead of 9 bits.
So far this is not a problem since all u-boot versions I have seen are
not using the cpu_scale_div clock at all (instead they are configuring
the CPU clock to run off cpu_in_sel directly).
The fixes tag points to the latest rework of the CPU clocks. However,
even before the rework it was wrong. Commit 7a29a869434e8b ("clk: meson:
Add support for Meson clock controller") defines MESON_N_WIDTH as 9 (in
drivers/clk/meson/clk-cpu.c). But since the old clk-cpu implementation
this only carries the fixes tag for the CPU clock rewordk.
The cpu_div3 clock (cpu_in divided by 3) generates a signal with a duty
cycle of 33%. The CPU clock however requires a clock signal with a duty
cycle of 50% to run stable.
cpu_div3 was observed to be problematic when cycling through all
available CPU frequencies (with additional patches on top of this one)
while running "stress --cpu 4" in the background. This caused sporadic
hangs where the whole system would fully lock up.
Amlogic's 3.10 kernel code also does not use the cpu_div3 clock either
when changing the CPU clock.
The rcar-du driver supports probe deferral for external clocks, but
implements it badly by checking the wrong pointer due to a bad copy and
paste. Fix it.
While at it, reject invalid clocks outright for DU channels that have a
display PLL, as the external clock is mandatory in that case. This
avoids a WARN_ON() at runtime.
Even though device object is not freed, fill_res_entry() can get called on
device which doesn't have a driver anymore. Kernel core device reference
count is not sufficient, as this only keeps the structure valid, and
doesn't guarantee the driver is still loaded.
Similar race can occur with device renaming and device removal, where
device_rename() tries to rename a unregistered device. While this is fine
for devices of a class which are not net namespace aware, but it is
incorrect for net namespace aware class coming in subsequent series. If a
class is net namespace aware, then the below [1] call trace is observed in
above situation.
Therefore, to avoid the race, keep a reference count and let device
unregistration wait until all netlink users drop the reference.
It's better not to positively BUG_ON the kernel, however developers
need a way to locate issues as soon as possible.
DBG_BUGON is introduced and it could only crash when EROFS_FS_DEBUG
(EROFS developping feature) is on. It is helpful for developers
to find and solve bugs quickly by eng builds.
Previously, DBG_BUGON is defined as ((void)0) if EROFS_FS_DEBUG is off,
but some unused variable warnings as follows could occur:
drivers/staging/erofs/unzip_vle.c: In function `init_alway:':
drivers/staging/erofs/unzip_vle.c:61:33: warning: unused variable `work' [-Wunused-variable]
struct z_erofs_vle_work *const work =
^~~~
of_parse_phandle() returns the device node with refcount incremented.
There are two nodes that are used temporary in mtk_vcodec_init_enc_pm(),
but their refcounts are not decremented.
The patch adds one of_node_put() and fixes returning error codes.
Found by Linux Driver Verification project (linuxtesting.org).
The video device release() callback for video-i2c driver frees the whole
struct video_i2c_data. If there is no user left for the video device
when video_unregister_device() is called, the release callback is executed.
However, in video_i2c_remove() some fields (v4l2_dev, lock, and queue_lock)
in struct video_i2c_data are still accessed after video_unregister_device()
is called.
This fixes the use after free by moving the code from video_i2c_remove()
to the release() callback.
Fixes: 5cebaac60974 ("media: video-i2c: add video-i2c driver") Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If userspace has an open file descriptor on the rc input device or lirc
device when rc_unregister_device() is called, then the rc close() is
never called.
This ensures that the receiver is turned off on the nuvoton-cir driver
during shutdown.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_tegra()
doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding: slightly rewrite to avoid inline comparison] Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I fixed a bug by adding a dependency in the network driver, but that fix
caused a related bug in the SCSI driver:
WARNING: unmet direct dependencies detected for CHELSIO_T4
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_CHELSIO [=y] && PCI [=y] && (IPV6 [=y] || IPV6 [=y]=n) && (THERMAL [=m] || !THERMAL [=m])
Selected by [y]:
- SCSI_CXGB4_ISCSI [=y] && SCSI_LOWLEVEL [=y] && SCSI [=y] && PCI [=y] && INET [=y] && (IPV6 [=y] || IPV6 [=y]=n)
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x158): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1d8): undefined reference to `thermal_zone_device_unregister'
/git/arm-soc/Makefile:1042: recipe for target 'vmlinux' failed
The same dependency needs to be propagated here to make it work correctly
with CONFIG_THERMAL=m and SCSI_CXGB4_ISCSI=y. That change by itself causes
another problem with a circular dependency, as we use 'select NETDEVICES'.
This is something we really should not do anyway, as a driver symbol should
never select another major subsystem, so let's turn that into a 'depends
on'. I don't see any downsides of that, as NETDEVICES is only disabled in
rather obscure cases that are not relevant to the users of cxgb4i.
Fixes: e70a57fa59bb ("cxgb4: fix thermal configuration dependencies") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The tool perf is useful for the performance analysis on the Hygon Dhyana
platform. But right now there is no Hygon support for it to analyze the
KVM guest os data. So add Hygon Dhyana support to it by checking vendor
string to share the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn> Acked-by: Borislav Petkov <bp@suse.de> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1542008451-31735-1-git-send-email-puwen@hygon.cn Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an ARM mapping symbol shares an address with a valid symbol,
find_elf_symbol can currently return the mapping symbol instead, as the
symbol is not validated. This can result in confusing warnings:
WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference
from the function set_reset_devices() to the variable .init.text:$x.0
This change adds a call to is_valid_name to find_elf_symbol, similarly
to how it's already used in find_elf_symbol2.
Currently the cpu affinity hint mask for completion EQs is stored and
read from the wrong place, since reading and storing is done from the
same index, there is no actual issue with that, but internal irq_info
for completion EQs stars at MLX5_EQ_VEC_COMP_BASE offset in irq_info
array, this patch changes the code to use the correct offset to store
and read the IRQ affinity hint.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 88cda1c9da02 ("bpf: libbpf: Provide basic API support
to specify BPF obj name"), libbpf unconditionally sets bpf_attr->name
for maps. Pre v4.14 kernels don't know about map names and return an
error about unexpected non-zero data. Retry sys_bpf without a map
name to cover older kernels.
v2 changes:
* check for errno == EINVAL as suggested by Daniel Borkmann
Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
phy_pix_clk is one of the variable used to check if one PLL can be shared
with displays having common mode set configuration. As of now
phy_pix_clock varialbe is calculated in function dc_validate_stream().
dc_validate_stream() function is called after clocks are assigned for the
new display. Due to this during hotplug, when PLL sharing conditions are
checked for new display phy_pix_clk variable will be 0 and for displays
that are already enabled phy_pix_clk will have some value. Hence PLL will
not be shared and if the display hardware doesn't have any more PLL to
assign, mode set will fail due to resource unavailability.
[how]
Instead of only calculating the phy_pix_clk variable after the PLL is
assigned for new display, this patch calculates phy_pix_clk also during
the before assigning the PLL for new display.
When building the kernel with Clang, the following section mismatch
warnings appears:
WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_iclk_autoidle()
The function _setup() references
the function __init _setup_iclk_autoidle().
This is often because _setup lacks a __init
annotation or the annotation of _setup_iclk_autoidle is wrong.
WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_reset()
The function _setup() references
the function __init _setup_reset().
This is often because _setup lacks a __init
annotation or the annotation of _setup_reset is wrong.
WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_postsetup()
The function _setup() references
the function __init _setup_postsetup().
This is often because _setup lacks a __init
annotation or the annotation of _setup_postsetup is wrong.
_setup is used in omap_hwmod_allocate_module, which isn't marked __init
and looks like it shouldn't be, meaning to fix these warnings, those
functions must be moved out of the init section, which this patch does.
Some of the functions (like cdn_dp_dpcd_read, cdn_dp_get_edid_block)
allow to read 64KiB, but the cdn_dp_mailbox_read_receive, that is
used by them, can read only up to 255 bytes at once. Normally, it's
not a big issue as DPCD or EDID reads won't (hopefully) exceed that
value.
The real issue here is the revocation list read during the HDCP
authentication process. (problematic use case:
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/rockchip/cdn-dp-reg.c#1152)
The list can reach 127*5+4 bytes (num devs * 5 bytes per ID/Bksv +
4 bytes of an additional info).
In other words - CTSes with HDCP Repeater won't pass without this
fix. Oh, and the driver will most likely stop working (best case
scenario).
The smsc95xx driver already takes into account the NET_IP_ALIGN
parameter when setting up the receive packet data, which means
we do not need to worry about aligning the packets in the usbnet
driver.
Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now
passed to the ip_rcv() routine with the start on an aligned address.
Tested on Raspberry Pi B3.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ad7780 driver previously did not read the correct device output, as
it read an outdated value set at initialization. It now updates its
voltage on read.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a TX hang occurs, we attempt to recover by incrementally resetting.
If we're starved for CPU time, it's possible the reset doesn't actually
complete (or even fire) before another tx_timeout fires causing us to
fly through the different resets without actually doing them.
This adds a bit to set and check if a timeout recovery is already
pending and, if so, bail out of tx_timeout. The bit will get cleared at
the end of i40e_rebuild when reset is complete.
Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The i40e driver complains about unprivileged VFs trying to configure
promiscuous mode each time a VF reset occurs. This isn't the fault of
the poor VF driver - the PF driver itself is making the request.
To fix this, skip the privilege check if the request is to disable all
promiscuous activity. This gets rid of the bogus message, but doesn't
affect privilege checks, since we really only care if the unprivileged
VF is trying to enable promiscuous mode.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
EC_MKBP_EVENT_SENSOR_FIFO events can be triggered for a variety of
reasons, and there are very few cases in which they should be treated as
wakeup interrupts (particularly, when a certain
MOTIONSENSE_MODULE_FLAG_* is set, but this is not even supported in the
mainline cros_ec_sensor driver yet). Most of the time, they are benign
sensor readings. In any case, the top-level cros_ec device doesn't know
enough to determine that they should wake the system, and so it should
not report the event. This would be the job of the cros_ec_sensors
driver to parse.
This patch adds checks to cros_ec_get_next_event() such that it doesn't
signal 'wakeup' for events of type EC_MKBP_EVENT_SENSOR_FIFO.
This patch is particularly relevant on devices like Scarlet (Rockchip
RK3399 tablet, known as Acer Chromebook Tab 10), where the EC firmware
reports sensor events much more frequently. This was causing
/sys/power/wakeup_count to increase very frequently, often needlessly
interrupting our ability to suspend the system.
With the new CONFIG_CC_OPTIMIZE_FOR_DEBUGGING option, we get a link
error in the vboxguest driver, when that fails to optimize out the
call to the compat handler:
drivers/virt/vboxguest/vboxguest_core.o: In function `vbg_ioctl_hgcm_call':
vboxguest_core.c:(.text+0x1f6e): undefined reference to `vbg_hgcm_call32'
Another compile-time check documents better what we want and avoids
the error.
Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If mapping the CvP BAR fails, we still can configure the FPGA via
PCI config space access. In this case the iomap pointer is NULL.
On x86_64, passing NULL address to pci_iounmap() generates
"Bad IO access at port 0x0" output with stack call trace. Fix it.
hv_kvp_daemon.c: In function 'kvp_set_ip_info':
hv_kvp_daemon.c:1305:2: note: 'snprintf' output between 41 and 4136 bytes
into a destination of size 4096
The "(unsigned int)str_len" is to avoid:
hv_kvp_daemon.c:1309:30: warning: comparison of integer expressions of
different signedness: 'int' and 'long unsigned int' [-Wsign-compare]
Signed-off-by: Dexuan Cui <decui@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:
- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.
Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.
If the association supports HE, HT/VHT rates will never be used for Tx
and therefore there's no need to set the sgi-per-channel-width-support
bits, so don't set them in this case.
Fixes: 110b32f065f3 ("iwlwifi: mvm: rs: add basic implementation of the new RS API handlers") Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fsl_mc_portal_allocate can fail when the requested MC portals are
not yet probed by the fsl_mc_allocator. In this situation, the driver
should defer the probe.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Intel EG20T Platform Controller Hub used on the MIPS Boston
development board supports prefetching memory to optimize DMA transfers.
Unfortunately for unknown reasons this doesn't work well with some MIPS
CPUs such as the P6600, particularly when using an I/O Coherence Unit
(IOCU) to provide cache-coherent DMA. In these systems it is common for
DMA data to be lost, resulting in broken access to EG20T devices such as
the MMC or SATA controllers.
Support for a DT property to configure the prefetching was added a while
back by commit 549ce8f134bd ("misc: pch_phub: Read prefetch value from
device tree if passed") but we never added the DT snippet to make use of
it. Add that now in order to disable the prefetching & fix DMA on the
affected systems.
If a gettime64 call fails, return the error and avoid copying data back
to user.
Cc: Richard Cochran <richardcochran@gmail.com> Cc: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current driver only enable parity enable bit and never clear it
when user set the termios. The fix clear the parity enable bit when
PARENB flag is not set in termios->c_cflag.
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
In the "aes-fixed-time" AES implementation, disable interrupts while
accessing the S-box, in order to make cache-timing attacks more
difficult. Previously it was possible for the CPU to be interrupted
while the S-box was loaded into L1 cache, potentially evicting the
cachelines and causing later table lookups to be time-variant.
In tests I did on x86 and ARM, this doesn't affect performance
significantly. Responsiveness is potentially a concern, but interrupts
are only disabled for a single AES block.
Note that even after this change, the implementation still isn't
necessarily guaranteed to be constant-time; see
https://cr.yp.to/antiforgery/cachetiming-20050414.pdf for a discussion
of the many difficulties involved in writing truly constant-time AES
software. But it's valuable to make such attacks more difficult.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
By default, READ MAC on a Layer2 OSD device returns the adapter's
burnt-in MAC address. Given the default scenario of many virtual devices
on the same adapter, qeth can't make any use of this address and
therefore skips the READ MAC call for this device type.
But in some configurations, the READ MAC command for a Layer2 OSD device
actually returns a pre-provisioned, virtual MAC address. So enable the
READ MAC code to detect this situation, and let the L2 subdriver
call READ MAC for OSD devices.
This also removes the QETH_LAYER2_MAC_READ flag, which protects L2
devices against calling READ MAC multiple times. Instead protect the
whole call to qeth_l2_request_initial_mac().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
bpftool output is not user friendly when dumping a map with only a few
populated entries:
$ bpftool map
1: devmap name tx_devmap flags 0x0
key 4B value 4B max_entries 64 memlock 4096B
2: array name tx_idxmap flags 0x0
key 4B value 4B max_entries 64 memlock 4096B
$ bpftool map dump id 1
key:
00 00 00 00
value:
No such file or directory
key:
01 00 00 00
value:
No such file or directory
key:
02 00 00 00
value:
No such file or directory
key: 03 00 00 00 value: 03 00 00 00
Handle ENOENT by keeping the line format sane and dumping
"<no entry>" for the value
The previous commit, "of: overlay: add missing of_node_get() in
__of_attach_node_sysfs" added a missing of_node_get() to
__of_attach_node_sysfs(). This results in a refcount imbalance
for nodes attached with dlpar_attach_node(). The calling sequence
from dlpar_attach_node() to __of_attach_node_sysfs() is:
In the expression "word1 << 16", word1 starts as u16, but is promoted to a
signed int, then sign-extended to resource_size_t, which is probably not
what was intended. Cast to resource_size_t to avoid the sign extension.
This fixes an identical issue as fixed by commit 0b2d70764bb3 ("x86/PCI:
Fix Broadcom CNB20LE unintended sign extension") back in 2014.
Detected by CoverityScan, CID#138749, 138750 ("Unintended sign extension")
Fixes: 3f6ea84a3035 ("PCI: read memory ranges out of Broadcom CNB20LE host bridge") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this patch, recovery would cause all callbacks to be delayed,
put on a queue, and afterward they were all queued to the callback
work queue. This patch does the same thing, but occasionally takes
a break after 25 of them so it won't swamp the CPU at the expense
of other RT processes like corosync.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch report warnings:
drivers/clk/imgtec/clk-boston.c:76 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:83 clk_boston_setup() warn: possible memory leak of 'onecell'
drivers/clk/imgtec/clk-boston.c:90 clk_boston_setup() warn: possible memory leak of 'onecell'
'onecell' is malloced in clk_boston_setup(), but not be freed
before leaving from the error handling cases.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case panic() and panic() called at the same time on different CPUS.
For example:
CPU 0:
panic()
__crash_kexec
machine_crash_shutdown
crash_smp_send_stop
machine_kexec
BUG_ON(num_online_cpus() > 1);
CPU 1:
panic()
local_irq_disable
panic_smp_self_stop
If CPU 1 calls panic_smp_self_stop() before crash_smp_send_stop(), kdump
fails. CPU1 can't receive the ipi irq, CPU1 will be always online.
To fix this problem, this patch split out the panic_smp_self_stop()
and add set_cpu_online(smp_processor_id(), false).
Signed-off-by: Yufen Wang <wangyufen@huawei.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
After a LOGO in response to an ABTS timeout, a PLOGI wasn't issued to
re-establish the login. An nlp_type check in the LOGO completion
handler failed to restart discovery for NVME targets. Revised the
nlp_type check for NVME as well as SCSI.
While reviewing the LOGO handling a few other issues were seen and
were addressed:
- Better lock synchronization around ndlp data types
- When the ABTS times out, unregister the RPI before sending the LOGO
so that all local exchange contexts are cleared and nothing received
while awaiting LOGO/PLOGI handling will be accepted.
- LOGO handling optimized to:
Wait only R_A_TOV for a response.
It doesn't need to be retried on timeout. If there wasn't a
response, a PLOGI will be sent, thus an implicit logout
applies as well when the other port sees it.
If there is a response, any kind of response is considered "good"
and the XRI quarantined for a exchange qualifier window.
- PLOGI is issued as soon a LOGO state is resolved.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Call sas_remove_host() before removing the target devices in the driver's
.remove() callback function(i.e. during driver unload time). So that
driver can provide a way to allow SYNC CACHE, START STOP unit commands
etc. (which are issued from SML) to the target drives during driver unload
time.
Once sas_remove_host() is called before removing the target drives then
driver can just clean up the resources allocated for target devices and no
need to call sas_port_delete_phy(), sas_port_delete() API's as these API's
internally called from sas_remove_host().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2ea9f12cefe4 ("ath10k: add new cipher suite support") added a new
n_cipher_suites HW param with a fallback value and a warning log. Commit 03a72288c546 ("ath10k: wmi: add hw params entry for wcn3990") later
added WCN3990 HW entries, but it missed the n_cipher_suites.
A successful call to wil_tx_ring takes skb reference so
it will only be freed in wil_tx_complete. Consume the skb
in wil_find_tx_bcast_2 to prevent memory leak.
Signed-off-by: Lior David <liord@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With current reset flow, Talyn sometimes get stuck causing PCIe
enumeration to fail. Fix this by removing some reset flow operations
that are not relevant for Talyn.
Setting bit 15 in RGF_HP_CTRL is WBE specific and is not in use for
all wil6210 devices.
For Sparrow, BIT_HPAL_PERST_FROM_PAD and BIT_CAR_PERST_RST were set
as a WA an HW issue.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / users / dwmw2 / linux.git / log